Search Documents

By T. S. Liu, E. A. Peretti

A LITERATURE survey of the In-Sb system, which was made before a study of the binary diagram was undertaken, revealed that the intermediate phase InSb existed and that its crystal structure is face-centered cubic of the zinc blend type. In 1929 Goldschmidt' determined the lattice constant for InSb and obtained a value of 6.452A. A more recent value, 6.461A was reported by Iandelli2 in 1941. The purity of the indium used was not very high, however. The indium used by Iandelli contained 2 pct Ge. In view of this fact it was decided to remeasure the lattice parameter using high-purity indium (99.97+ pct In) and spectrographically standardized antimony of the highest purity available (99.91 pct Sb). Specimens corresponding to the InSb composition were made by carefully weighing the ingredients on an analytical balance and heating them in vacuo in a quartz tube at 700°C. As melting losses were negligible, the alloys were not analyzed chemically, but the intended analysis was taken as being accu- rate. Powder samples were prepared by either filing or crushing of the brittle alloy, followed by screening at 325 mesh. The powders were then annealed at 400°C in evacuated capsules for about an hour. X-ray photograms were taken with a Debye and a back-reflection focusing camera, using characteristic cobalt K. radiation. Lattice parameters were calculated by Cohen's³ method. The results of a Debye pattern and of a back-reflection pattern at 25°C are given in Tables I and 11. The lattice parameter at 25 °C is 6.47602A.

Jan 1, 1952

By R. A. Fitch, J. D. Griffith

A performance calculation method was used in conjunction with experimental studies to develop means of predicting and interpreting miscible floods and to explore possible methods. of improving their efficiency. The calculation method is based upon the division of reservoirs into multiple independent zones or strata. Comparison was made with some experimental floods and with a field project to obtain some measure of the applicability of the method. Two aspects of miscible flooding were considered: (I) the displacement of a miscible front through a reservoir, and (2) the distribution and utilization of the solvent volume injected to maintain miscibility. Calculations and experihental observations indicate that alternate gas-water injection behind a miscible front significantly improves miscible flood performance, both within a single stratum and in a multistrata reservoir. Calculations were made on the extent to which miscibiliry is maintained by a given solvent volume in a stratified reservoir. Two alternate criteria for determining the optimum volume of solvent for injection are discussed. The preinjection of a small volume of water ahead of the solvent is suggested as a method of obtaining more efficient utilization of solvent. Calculations and experiments were made to investigate the effects of water preinjection. INTRODUCTION Miscible fluid displacement as a possible means of recovering oil has been the subject of extensive research and numerous field tests over the past several years. This work has brought out both favorable and unfavorable features of the miscible recovery methods. Many tests have shown that a miscible fluid can displace all of the oil contacted, leaving no high residual oil saturation, as is characteristic of immiscible displacements. The miscible methods have proven dificult to control, however, as evidenced by early breakthrough of the displacing fluid and poor sweep efficiency in several field projects. It became apparent early in the investigation of miscible displacement that the development of improved techniques and better methods of control would be required to extend the range of applicability to any significant portion of our petroleum reservoirs. The purpose of this study was to consider the problem of designing miscible floods to obtain better performance. A performance calculation was used in conjunction with experimental studies to develop means of predicting and interpreting miscible floods and to explore possible methods of improving their efficiency. Two aspects of miscible floods were considered separately in this study and the results are presented in two parts. The first part concerns the manner in which the miscible front is displaced through the reservoir. In these calculations the condition of miscibility between the reservoir oil and the displacing fluid is assumed. In the second portion the distribution and utilization of the preinjected solvent in maintaining rniscibility is considered. This portion dealing with solvent utilization applies only to the enriched gas or LPG slug processes. CALCULATION METHOD AND EXPERIMENTAL STUDIES COMPUTATIONAL MODEL The calculations for expected reservoir performance are based upon the multi-strata concept of reservoir properties. The method assumes multiple, independent strata (no crossflow between strata) and explicitly includes variations in patterns, injectivity, areal sweep and displacement efficiency. Lateral variation in permeability within the strata (for example, directional permeability) may be considered in the calculations, provided the variations are similar in all strata. The calculations based on this model furnish the rates of injection and rates of production of both oil and the displacing fluid for the composite system of strata. To carry out calculations on the mathematical model described, information is required on the performance of the displacement process under consideration in a single stratum element of the pattern to be used. In particular, for a given pattern and displacement process, data are required relating injectivity and composition of the produced stream to the volume of fluid injected. Data on the variations in areal sweep must also be available if it is desired to track the areal sweeps in the multi-strata model. These data may be obtained from experimental work such as model studies or other suitable methods. This representation of reservoir properties is, of course, an approximation and may be inappropriate in some cases. But the representation is not an arbitrary one since most oil reservoirs are essentially successive layers of sediment with the net producing pay zone often comprising but a fraction of the gross formation thickness. The fact that permeabilities measured in the vertical direction are frequently but a fraction of the horizontal permeability adds some evidence to the validity of this model. This type cal-

Jan 1, 1965

By G. E. Archie

The usefulness of the electrical resistivity log in determining reservoir characteristics is governed largely by: (I) the accuracy with which the true resistivity of the formation can be determined; (2) the scope of detailed data concerning the relation of resistivity measurements to formation characteristics; (3) the available information concerning the conductivity of connate or formation waters; (4) the extent of geologic knowledge regarding probable changes in facies within given horizons, both vertically and laterally, particularly in relation to the resultant effect on the electrical properties of the reservoir. Simple examples are given in the following pages to illustrate the use of resistivity logs in the solution of some problems dealing with oil and gas reservoirs. From the available information, it is apparent that much care must be exercised in applying to more complicated cases the methods suggested. It should be remembered that the equations given are not precise and represent only approximate relationships. It is believed, however, that under favorable conditions their application falls within useful limits of accuracy. Introduction The electrical log has been used extensively in a qualitative way to correlate formations penetrated by the drill in the exploitation of oil and gas reservoirs and to provide some indication of reservoir content. However, its use in a quantitative way has been limited because of various factors that tend to obscure the significance of the electrical readings obtained. Some of these factors are the borehole size, . the resistivity of the mud in the borehole, the effect of invasion of the mud filtrate into the formation, the relation of the recorded thickness of beds to electrode spacing, the heterogeneity of geologic formations, the salinity or conductivity of connate water, and, perhaps of greatest importance, the lack of data indicating the relationship of the resistivity of a formation in situ to its character and fluid content. On the Gulf Coast it is found that the effects of the size of the borehole and the mud resistivity are generally of little importance, except when dealing with high formational resistivities or extremely low mud resistivities. Fortunately, little practical significance need be attached to the exact values of the higher resistivities recorded. Low mud resistivities are not common, but when this condition is encountered it may be corrected by replacing the mud column. With the present advanced knowledge of mud control, invasion of mud filtrate into sands can be minimized, thereby increasing the dependability of the electrical log. The effect of electrode spacing on the recorded thickness of a bed is often subject to compensation or can be sufficiently accounted for to provide an acceptable approximation of the true resistivity of the formation. As development of a field or area progressively enhances the knowledge of the lithologic section, the resistivity values of the electrical log take on greater significance, ultimately affording acceptable interpretations. The salinity, and

Jan 1, 1942

By G. E. Archie

The usefulness of the electrical resistivity log in determining reservoir characteristics is governed largely by: (I) the accuracy with which the true resistivity of the formation can be determined; (2) the scope of detailed data concerning the relation of resistivity measurements to formation characteristics; (3) the available information concerning the conductivity of connate or formation waters; (4) the extent of geologic knowledge regarding probable changes in facies within given horizons, both vertically and laterally, particularly in relation to the resultant effect on the electrical properties of the reservoir. Simple examples are given in the following pages to illustrate the use of resistivity logs in the solution of some problems dealing with oil and gas reservoirs. From the available information, it is apparent that much care must be exercised in applying to more complicated cases the methods suggested. It should be remembered that the equations given are not precise and represent only approximate relationships. It is believed, however, that under favorable conditions their application falls within useful limits of accuracy. Introduction The electrical log has been used extensively in a qualitative way to correlate formations penetrated by the drill in the exploitation of oil and gas reservoirs and to provide some indication of reservoir content. However, its use in a quantitative way has been limited because of various factors that tend to obscure the significance of the electrical readings obtained. Some of these factors are the borehole size, . the resistivity of the mud in the borehole, the effect of invasion of the mud filtrate into the formation, the relation of the recorded thickness of beds to electrode spacing, the heterogeneity of geologic formations, the salinity or conductivity of connate water, and, perhaps of greatest importance, the lack of data indicating the relationship of the resistivity of a formation in situ to its character and fluid content. On the Gulf Coast it is found that the effects of the size of the borehole and the mud resistivity are generally of little importance, except when dealing with high formational resistivities or extremely low mud resistivities. Fortunately, little practical significance need be attached to the exact values of the higher resistivities recorded. Low mud resistivities are not common, but when this condition is encountered it may be corrected by replacing the mud column. With the present advanced knowledge of mud control, invasion of mud filtrate into sands can be minimized, thereby increasing the dependability of the electrical log. The effect of electrode spacing on the recorded thickness of a bed is often subject to compensation or can be sufficiently accounted for to provide an acceptable approximation of the true resistivity of the formation. As development of a field or area progressively enhances the knowledge of the lithologic section, the resistivity values of the electrical log take on greater significance, ultimately affording acceptable interpretations. The salinity, and

Jan 1, 1942

By H. M. Warren, E. J. Powell, A. S. Biesecker

In the past, steam engines were used in practically all cases for driving the machinery in and about an anthracite breaker, and hence few or no accurate data were available as to the power requirements for starting and operating the individual machines, which make up the complete equipment. It was impossible to segregate the power necessary to drive each individual machine, first, because the equipment was driven in groups, and second, because it was impracticable to obtain graphic, integrated, or instantaneous records of the horsepower used. As a result of these conditions, it was found, when individual electric motors were applied to the various machines, that more accurate and complete data were needed in order to provide motors of the proper power and design for the particular services to be rendered. In order to obtain the desired information, the writers made and collected a number of tests, from time to time, on the individual motor drives in electrically operated breakers, and as these tests have been of great value, it occurred to them that a paper giving the results might be of service to other engineers interested in similar installations. Table I shows the results of these tests. All the motors tested were of the three-phase, 60-cycle, 440-volt, induction, squirrel-cage type, except a few, which, on account of size and starting conditions, were of the wound-rotor type. The instruments used in making these tests were: An integrating watt-hour meter, a graphic ammeter, and a graphic voltmeter. These instruments were connected in each motor circuit, and a record of a day's run of 9 hours was obtained from each machine. From these tests, the running light load, the average all-day load, and the instantaneous peak readings in amperes, volts, and kilowatt input, were obtained. By means of the characteristic curves obtained from these motors at the factory, the power factor, the efficiency, and the horsepower output were calculated for each particular test. Starting tests were made by the brake-arm method, in which the torque in pounds was measured directly on a spring balance.

Jan 1, 1916

By Charles D. Walcott

The following acts of the Directors are reported for the information of members At a meeting held June 20, 1907, Dr. Charles D. Walcott, Director of the U. S. Geological Survey, Washington, D. C., having been recommended by unanimous vote of the Council, was unanimously elected an Honorary Member of the American Institute of Mining Engineers, in recognition of his personal services to American geology, and of his generous co-operation with this Institute, to the Transactions of which he has not only himself made valuable contributions, but has also encouraged the preparation of such contributions by the members of the U. S. Geological Survey under his charge, his liberal policy in this respect having gone so far as to permit the preliminary publication by the Institute of important results reached by the geologists of that Survey, even before their final and full publication as public documents. This wise and generous course has not only brought the U. S. Geological Survey into intimate and sympathetic relations with the mining industry of the world, but has also enriched the Transactions of the Institute, especially in the department of the science of ore-deposits, with many valuable papers. At a meeting held Jan. 14, 1908, Mr. Charles Kirchhoff was unanimously re-elected a Trustee of the United Engineering Society, to serve for a second term of three years. At a meeting held Feb. 18, 1908, directly after the adjournment of the annual meeting of the Institute, the following officers were elected for the ensuing year: President, James Gayley: Vice-President, James Douglas; Secretary, R. W. Raymond; Treasurer, Frank Lyman.

Mar 1, 1908

By J. J. Bowman, E. H. Dix

A lack of experimental data illustrating the effect of composition, particularly in respect to impurities, on the mechanical properties and corrosion resistance of aluminum-alloy die castings induced the authors and their associates to undertake a limited study of these relations. A number of commercial alloys and several experimental variations of a commercial alloy were used for the investigation. Mechanical property, growth, steam, paraffin, salt spray and atmospheric exposure tests were employed. This paper deals with the more accelerated tests and the results they have produced. It is concluded that a high-silicon alloy with all impurities except iron strictly limited to small amounts will develop an excellent resistance to corrosion and retain satisfactory mechanical properties and casting characteristics. As a direct result of this investigation an alloy of this character with superior corrosion resistance is now available commercially. In general, copper increases the strength and decreases the elongation and corrosion resistance. Tin reduces the mechanical properties and the resistance to corrosion. Iron reduces the elongation and, if excessively high, may adversely affect the tensile strength. Even excessively high iron contents do not affect the corrosion resistance, which is fortunate for the die caster as it is this element that is the most difficult to control. Nickel and zinc in limited amounts do not seem to affect the properties or corrosion resistance of at least the high-silicon alloy. Growth tests have confirmed the previous common belief that dimensional changes under either dry or wet conditions at 100" C. are too small to be of practical importance. Introduction The technical literature contains numerous papers describing die castings, their production, compositions and uses, but nearly all of these

Jan 1, 1935

By F. Cadena

Hiwassee Darn, now under construction by the Tennessee Valley Authority on the Hiwassee River, a tributary of the Tennessee River, will require aggregate for approximately 800,000 cu. yd. of concrete. Near the damsite deposits of natural sand or gravel are not available and graywacke, a rock that is found in abundance, suggested itself as a likely source of manufactured aggregate. Graywacke is a metamorphosed sandstone composed principally of a mixture of quartz (65 per cent), mica (25 per cent), and feldspar (10 per cent). Other minerals are present in negligible amounts. The rock varies in different parts of the quarry from very fine to a coarse grain containing particles of about ¼ in. maximum size, although the bulk of the deposit is medium grain. Extensive tests showed that graywacke would be suitable as a source of both coarse and fine aggregates. The aggregate plant available for use at Hiwassee Dam consisted of the coarse-aggregate and sand plant used on the Norris project. The coarse-aggregate plant had also been used at Chickamauga Dam. Although most of this plant equipment is now in use at Hiwassee, the present flowsheet is not only different from that at Norris and Chickamauga but is also unique as compared to the flowsheet of the average crushed-stone aggregate plant. It is hoped that this paper will show the importance of proper arrangement of equipment if the optimum in flexibility and capacity is to be attained. Flowsheet Rock is ioaded by 3-yd. electric shovels into 12-yd. dump trucks, which carry the rock to the primary crusher, a 42-in. Superior McCully gyratory unit set at 4¾ in. (Fig. 1). The primary crusher discharges directly onto a 42-in. inclined belt conveyor, which carries the product to a surge storage pile with a maximum live storage capacity of approximately 3000 tons. A concrete tunnel under this storage pile houses the feed end of a 36-in. belt conveyor (conveyor B) fed by a 36 by 66-in.

Jan 1, 1942

By F. Cadena

Hiwassee Darn, now under construction by the Tennessee Valley Authority on the Hiwassee River, a tributary of the Tennessee River, will require aggregate for approximately 800,000 cu. yd. of concrete. Near the damsite deposits of natural sand or gravel are not available and graywacke, a rock that is found in abundance, suggested itself as a likely source of manufactured aggregate. Graywacke is a metamorphosed sandstone composed principally of a mixture of quartz (65 per cent), mica (25 per cent), and feldspar (10 per cent). Other minerals are present in negligible amounts. The rock varies in different parts of the quarry from very fine to a coarse grain containing particles of about ¼ in. maximum size, although the bulk of the deposit is medium grain. Extensive tests showed that graywacke would be suitable as a source of both coarse and fine aggregates. The aggregate plant available for use at Hiwassee Dam consisted of the coarse-aggregate and sand plant used on the Norris project. The coarse-aggregate plant had also been used at Chickamauga Dam. Although most of this plant equipment is now in use at Hiwassee, the present flowsheet is not only different from that at Norris and Chickamauga but is also unique as compared to the flowsheet of the average crushed-stone aggregate plant. It is hoped that this paper will show the importance of proper arrangement of equipment if the optimum in flexibility and capacity is to be attained. Flowsheet Rock is ioaded by 3-yd. electric shovels into 12-yd. dump trucks, which carry the rock to the primary crusher, a 42-in. Superior McCully gyratory unit set at 4¾ in. (Fig. 1). The primary crusher discharges directly onto a 42-in. inclined belt conveyor, which carries the product to a surge storage pile with a maximum live storage capacity of approximately 3000 tons. A concrete tunnel under this storage pile houses the feed end of a 36-in. belt conveyor (conveyor B) fed by a 36 by 66-in.

Jan 1, 1942

By J. J. Bowman, E. H. Dix

A lack of experimental data illustrating the effect of composition, particularly in respect to impurities, on the mechanical properties and corrosion resistance of aluminum-alloy die castings induced the authors and their associates to undertake a limited study of these relations. A number of commercial alloys and several experimental variations of a commercial alloy were used for the investigation. Mechanical property, growth, steam, paraffin, salt spray and atmospheric exposure tests were employed. This paper deals with the more accelerated tests and the results they have produced. It is concluded that a high-silicon alloy with all impurities except iron strictly limited to small amounts will develop an excellent resistance to corrosion and retain satisfactory mechanical properties and casting characteristics. As a direct result of this investigation an alloy of this character with superior corrosion resistance is now available commercially. In general, copper increases the strength and decreases the elongation and corrosion resistance. Tin reduces the mechanical properties and the resistance to corrosion. Iron reduces the elongation and, if excessively high, may adversely affect the tensile strength. Even excessively high iron contents do not affect the corrosion resistance, which is fortunate for the die caster as it is this element that is the most difficult to control. Nickel and zinc in limited amounts do not seem to affect the properties or corrosion resistance of at least the high-silicon alloy. Growth tests have confirmed the previous common belief that dimensional changes under either dry or wet conditions at 100" C. are too small to be of practical importance. Introduction The technical literature contains numerous papers describing die castings, their production, compositions and uses, but nearly all of these

Jan 1, 1935

By David H. Browne

The use of coal-dust fired reverberatory furnaces, or indeed of rever-beratory furnaces of any description, was for the Canadian Copper Co. a matter of necessity, and not of choice. For 20 years smelting had been done in blast furnaces alone, and with the Herreshoff furnaces used prior to 1904 there was no trouble in treating fine ores. But little flue dust was produced, and this, following the time-honored custom, was wetted down and put back with the charge. Whether the flue dust really smelted, or whether it was worn out by being chased around in a circle, was a problem that troubled no one. With the installation of modern blast furnaces and high-pressure blowing engines, in 1904, flue dust commenced to assert itself. Evidently more dust was made than could be smelted, but so many vital. problems engaged our attention at that time that this minor question was pushed to one side. In 1906, the details of blast-furnace smelting and the conversion of matte had been worked out to a satisfactory conclusion, and the ever-increasing piles of flue dust and fine ore on the stock yard demanded serious consideration. Numerous experiments in sintering, briquetting, mixing with converter slag, forming blocks of flue dust with green-ore fines and cement, and so on, were undertaken. None of these showed much promise. Our problem was still further complicated by the question of treating converter slag. The ore was basic, the slag was not needed as a furnace flux, and it was felt that under these conditions the old method of pouring slag in molds and resmelting in the blast furnace was an unnecessary expense. If the converter slag could be settled in basic-lined reverberatory furnaces, in which at the same time flue dust and green-ore fines could be smelted, two problems might thus be solved. Reverberatory practice with our ores was, however, an unknown factor. As carried on in the West, on siliceous ores and concentrates, at least 25 per cent. of fuel was required, and even this ratio depended greatly

Jan 1, 1915

By H. Biloni, H. R. Bertorello

GruZLESKI and winegard1 have recently reported on the origin and development of the cellular substructure in Sn-Cd eutectic unidirectionally grown with different amounts of constitutional supercooling (CS). This communication deals with the results obtained in a parallel study on the instability of a plane interface in Al-Cu eutectic unidirectionally grown. Similarities as well as differences with the results of these authors1 will be presented. A1-Cu eutectic alloy ingots of 99.999 pct purity were grown unidirectionally under different G/R ratios where G = thermal gradient in the liquid, R = solidification rate. The ingots were cut in slices perpendicular to the solidification axes and the substructure studied on parallel sections following the sense of growth. It was generally found that the last part of the ingot to solidify presented a well developed colony substructure as a result of impurity build up and constitutional supercooling. The results obtained were: 1) When the structure was observed with low niagnification (of the order of 150 to 300 times) the first instabilities were observed at the grain boundaries and node-like structures formed at the junctions of the growth-induced boundaries, as reported by Gruz-leski and Winegard.1 Inside the grains the first signs of instability appear later and correspond to the type shown in Fig. 1; this is a two dimensional cell substructure. ' 2) Figs. 2 and 3 correspond to the evolution from a two dimensional substructure to a cellular type. In the A1-Cu eutectic the boundaries of the two dimensional cell are always perpendicular to the laniellaes instead of parallel as in the Sn-Cd eutectic. 1

Jan 1, 1970

By R. D. Brown

This paper profiles Canada’s current economic, tax, and political environment with respect to its mining industry. Problems that must be overcome if the industry is to attain its full growth potential and are highlighted, some suggestions reflecting the opinion of many in the industry are given. Tables provide some detail on the current Canadian mining tax system, province by province, as well as for the Yukon and Northwest Territories, plus some relevant economic trends.

Jan 1, 1985

By C. V. Corless

We are living at a period of the world's history in which social phenomena are on so vast a scale, are of so profoundly soul-searching a nature, and are occurring in such rapid succession in the great world drama in which we are both actors and spectators, that, in our efforts to obtain a rational point of view in relation to them, our minds may fail to discern the simple in the complex and our understanding is liable to become confused or even overwhelmed. To the social student whose: scientific training has convinced him of the truth of the evolutionary law, Natura non facit salium, it is neither the vast scale of the events, their deeply soul-stirring nature, nor their rapid succession that matters so much, as the discovery of the underlying principle or law in accordance with which the disintegration and reintegration, which are the two aspects of social evolution, or indeed of evolution everywhere, are occurring. He is most deeply concerned in seeking an answer to the question: Have we in the present great and perplexing upheavals in human society, whether regarded in Central Europe, in Russia, in Great Britain, or in America, a really new cause at work, or, have we, though on a very large scale, merely new manifestations of the working out of an old principle? When we think of the appalling struggle in Europe, into which the world's greatest exemplar of democracy was finally drawn, no one has any hesitation in admitting that the great conflict was fundamentally a life-and-death struggle for self-preservation and self-propagation on the part of autocracy. The variations we meet with in the statement of the cause of the war arise mainly from differing distances of perspective; but in the last analysis all agree that the autocratic system of political gov ernment, which found its very soul and center in Prussian despotism, was consciously arrayed in a final "world-power-or-downf all" struggle against a love of freedom which was steadily widening and deepening throughout the world, and particularly throughout those parts of the world where this love of freedom and justice hasfound expressionin democratic institutions. It is not irrelevant to our discussion to recall in passing that this most imposing structure ever conceived by the human mind as an instrument of tyranny is lying today an irretrievable mass of ruins, completely over-

Jan 1, 1920

By H. A. Koch, R. L. Slobod

This paper discusses a new oil recovery process called the "miscible slug process." This process involves the injection of propane or LPG into the reservoir prior to gas injection. The operating conditions are maintained so that the slug is miscible with both the reservoir oil and the injected gas phase. Thus, a miscible phase displacement is achieved, and high recoveries are obtained from the area of the reservoir contacted. The most striking discovery of the laboratory study which included displacements from cores up to 123 ft in length was that relatively small slugs of LPG are effective over reservoir distances in the miscible displacement of oil. This makes possible the commercial application of the process. The important factors controlling the size of the slug are: (I) reservoir length, (2) reservoir fluid composition, and (3) reservoir pressure at the displacement front. Of lesser importance are the effects of injection rate and porous medium type. Questions which have not been completely answered deal with the effects of gravity and reservoir inhomogeneities on the process. INTRODUCTION One of the major problems facing the oil industry today is recovery of the large fraction of the discovered oil which will remain unrecovered unless some new processes are found. Water flooding has been one successful method used to increase recovery over natural depletion. But even successful water floods may leave 25 to 40 per cent of the pore space filled with residual oil. Recently a process which involves the use of thermal energy has been reported1,'*' which may prove useful in increasing recovery from shallow reservoirs containing highly viscous crudes. This paper deals with a new oil recovery process involving use of miscible phases to displace the oil from the reservoir. Miscible phase displacement oil has been an intriguing idea because the elimination of capillary effects in the reservoir leads to 100 per cent recovery in the areas contacted by the miscible displacing phase. The big deterrent in the past to the practice of miscible phase displacement has been the high cost involved in using large volumes of solvent in the process. The use of high pressure gas to achieve a miscible phase displacement of reservoir oil has been reported4,5 as one economically feasible method. However, this process calls for the maintenance of pressures above 3,000 psi at the dis-placement front. The process described in this paper is not restricted to high reservoir pressures; the only qualification being that the slug of material which is injected into the reservoir must be miscible with both the displaced oil 2nd the displacing phase. Two such cases are the use of an alcohol slug followed by water to achieve a mis-cable water flood, and the use of a low boiling hydrocarbon slug such as propane followed by gas to achieve a miscible gas drive. This paper will deal specifically with the propane dug process. This process will obtain a miscible phase displacement at pressures as low as about 1,200 psi at a reservoir temperature 01 150°F. The process is very simple. The propane displaces oil completely at one front because it is miscible with the oil, and gas displaces the propane completely at a second or trailing front because it is miscible with the propane. A small band of propane should thus remain wedged between the gas and oil phases. This idea has been called the "miscible slug process."6 Unfortunately, the propane slug will become diluted as it flows through the reservoir. This results from a mixing action since the fluids flow through a complex reservoir porous medium rather than simple capillaries. Fig. 1 diagrams a miscible slug displacement. The effects of some of

Jan 1, 1958

By J. W. Snavely

THE high tension belt conveyor is introducing a new and tremendously expanded era of low cost bulk material handling. High tension belt conveyors are generally those installations involving very long centers, high lifts, or drops, in which the belts are stressed up to their maximum tension values, and further, where the belt construction provides tension capacity far beyond what is possible with conventional belt constructions. With these high tension installations, the magnitude of the forces involved demands careful refinement of accepted design practice in order to achieve optimum balance of all factors. No attempt will be made to evaluate the relative merits of belt conveyor haulage with other means of transportation. For present purposes, it is assumed this has already been done in favor of belt conveyor. Neither will any attempt be made to evaluate the various conveyor belt constructions now available or to balance the advantages of various types of mechanical equipment. It is also assumed that the basic haulage information on which the conveyor design is based is accurate and complete. A sustained maximum, uniform load on the belt at all times must be achieved through proper feed control and the use of adequate surge storage to level the peaks and valleys of any varying demand for the material being handled. General Belt Capacity Considerations The belt conveyor capacity tables published by various belting and conveyor equipment manufacturers vary to a considerable degree, and the ratings given are quite conservative. Of necessity, these published ratings are based on the handling of average materials under average conditions. In applying a high tension belt, all possible capacity from the belt must be obtained in order to hold its width to a minimum and thereby limit the initial cost. Two factors are involved, loading to maximum cross section area and traveling at a maximum practical speed. Belt Loading: Proper treatment of the loading of the belt will result in maximum cross section to the load, and published capacity ratings can be exceeded, sometimes by appreciable margins. On the 10-mile conveyor haul used in the construction of Shasta Dam, California, although the rated capacity of the belt line was 1100 tons per hr, at times the system handled peak loads of 1400 tons per hr, almost 25 pct better than the rated capacity. One of the large coal companies has been able to exceed rated capacity by as much as 50 pct. Loading conditions which must be controlled are: 1. Large lumps must be scalped off and rejected or the load must be primary crushed before being placed on the belt. 2. The material weight per cubic foot must be accurate, must be known for all the materials being handled, and must be known for the complete range of conditions of the individual material being handled. Long centers and high lifts magnify small differences into serious proportions. 3. Uniform feeding to the belt is most important. Various types of feeders are available, which can be used to place a constant predetermined volume of material on the belt, or, where an appreciable range of material weight exists, through electrical control actuated by current demand, to place a predetermined uniform tonnage on the belt. One long slope belt in a coal mine in Pennsylvania is being fed at three separate stations with the controls so arranged that whenever the maximum load is going onto the belt from the first station, the other two stations automatically cut out. Whenever the load from the first station drops back, the other two stations again automatically cut in. 4. Careful design of the chutes and skirts is necessary to get the load centered on the belt with a minimum of free margin along each edge. Some free margin at the edge of the belt is necessary to prevent spillage, but if the load can be kept accurately centered, this free margin area can be reduced, and more material can be carried on the belt. What can be accomplished in this respect will vary widely, depending on the nature of the material being hauled. The chute and skirt design must also protect the belt. 5. The design of chutes and skirts should also get the load traveling in the same direction and close to belt speed, so that the load comes to rest on the belt as quickly as possible. The design of the chutes and skirts is worthy of careful study, and after a system is put into operation it should be experimented with to get the best results. Belt Speed: High belt speeds should be used in high tension work. Obviously, high belt speeds enable haulage on a narrower belt, reducing initial cost. The major portion of belt wear takes place at the loading point and around the terminal pulleys. The

Jan 1, 1952

By R. B. Hoy, Stanley J. LeFond, K. Reckling

World production of natural diamonds prob¬ably exceeds 50,000,000 carats a year. The Republic of Zaire is the leading producer, with an output which is primarily industrial rather than gem grade. The USSR ranks second, and the Republic of South Africa third. Diamonds are also mined in South-West Africa, Angola, Ghana, Sierra Leone, and other African coun¬tries. In the western hemisphere, Brazil and Venezuela are the principal producers (Fig. 1). A very small output of diamonds is mined today in India, which was the first source of commercial production. In the U.S., efforts at commercial diamond mining have been con¬fined to a small area near Murfreesboro, Ark. The first diamond was found in a kimberlite pipe there in 1906. Small-scale trial mining has not, however, proved economical. Since diamonds were first discovered over 2000 years ago, only about 130 tons have been mined. In order to obtain 1 g (5 carats) of diamonds, it is necessary to remove and process approximately 25 tons of rock. Recovering this small percentage involves a combination of highly developed techniques in mining, quarrying, and earth-moving, and extremely sophisticated recovery processes. End Uses Diamonds are used for two unrelated end uses; gem diamonds are jewels of great beauty while industrial diamonds are essential ma¬terials of modern industry. Although imitation stones are substituted for the gem diamond, none of these matches its properties sufficiently well to offer real competition. Synthetic indus¬trial diamonds are now of a quality that per¬mits wide substitution in the fine-grained sizes. Gem Diamonds A diamond is a natural prism. It has the ability to bounce light rays (reflection), to bend them (refraction), and to break them into all colors of the rainbow (dispersion). This ability to "modify" light gives the diamond three characteristics for providing beauty. First is brilliance, the reflection of light back to the eye. Second is fire, dispersion of light into the colors of the spectrum. Third is scintillation, the "twinkling" that occurs when the diamond is moved (Bauer, 1969). The skill of the diamond cutter is required to unlock the brilliant, fiery beauty of a gem dia¬mond (Fisher, 1966). Diamond-cutting skills have gradually developed over the centuries. The first cutters, in India, learned how to grind one rough diamond against another to remove their "skins" and to give them various shapes. This revealed some fire and beauty, but little compared to that of the diamonds that are cut today. About 1475, a Flemish cutter named Van Gerquem discovered that diamond dust on an iron wheel would polish facets on a diamond to provide more brilliance and fire. Cutters continued to experiment with facets, and shortly before 1700 a Venetian cutter named Peruzzi developed the 58-facet brilliant cut. With the development of the science of optics, cutters have learned more about the behavior of light within the diamond. Early in the 20th century, they learned how to angle Peruzzi's

Jan 1, 1975

By B. D. Cullity

AS methods for measuring fiber textures become more exact, it becomes justifiable to scrutinize an observed pole-density curve for evidence of minor texture components. These are disclosed by minor maxima or abnormally broad major maxima. One possible source of these minor components is twinning of the main component. In cubic metals and alloys, there are two kinds of twins: 1) Annealing twins in face-centered cubic metals. These are reflection twins on {Ill), and they can be expected to be present in recrystallization textures. 2) Deformation twins in body-centered cubic metals. These are shear twins on (112). Although usually formed only by impact, they might conceivably be present in the deformation texture of severely cold-drawn wire. Fortunately, both kinds of twinning lead to the same orientation relationships. It thus becomes possible to prepare a single list of angles between various planes in parent crystal and twin, which is helpful in examining pole-density curves for evidence of twinning in any cubic metal or alloy. Such a list of interplanar angles is given in Table I. This table consists of three parts, corresponding to the three major texture components—<100>, <110>, and <111>-most commonly found in the fiber textures of cubic metals. The table lists the angle between the pole of {hkl}, in either the parent crystal P or the twin T, and the fiber axis <uvu>. The crystals with <uvw> parallel to the wire axis are here

Jan 1, 1959

By S. K. Nowak

The lithium solubility limit in solid aluminum was determined by the use of micro-graphic techniques. The solubility limit thus established was shown to be a true equilibrium by checking the reversibility of AlLi phase precipitation and dissolution around the equilibrium temperature. The experimental results fit a straight line by plotting log N(LI) against 1/T. The metallurgical reasons explaining the lack of agreement among previous investigations are discussed. THE solubility limit of lithium in solid aluminum was determined by Shamray and Saldau1 by micrography and by Grube et al.&apos; and also Voss-Kiihler- by measurement of electrical resistivity. Since the addition of lithium induces extremely small changes in the aluminum lattice, X-ray techniques could not be employed for this purpose; in fact, the addition of lithium does not cause an expansion of the lattice as might be expected from a consideration of atomic radii, but causes a small contraction from 4.040 to 4.037A3, 4 when the solvent aluminum is saturated with this element. An analysis of the results from previous investiga-tions&apos;" shows that with improvement of investigation techniques the solubility limit tends toward a lower lithium content. Again, some of the author&apos;s own experimental results on the action of atomic hydrogen on A1-Li alloys seemed to indicate that the solubility of lithium should be much lower, i.e., about 0.3 pet at 300°C: instead of 1.15 pet, the lowest published value.4 For the foregoing reasons it was decided to investigate this problem. The aluminum and the lithium used for this purpose were of the highest purity. The lithium solubility limit was determined by metallographic techniques, in particular by the use of a reagent especially developed for the purpose of revealing the AlLi phase. The solubility limit thus determined was shown to be a true equilibrium by checking the reversibility of AlLi phase dissolution and precipitation around the equilibrium temperature. All of the experimental work was carried out in 1951 at the Centre d&apos;Etudes de Chimie Metallur-gique at Vitry, France, under the direction of Georges Chaudron.

Jan 1, 1957

By Henry Louis

The work performed by the Royal Commission on Mining Subsidence is likely to prove of permancnt value, less perhaps for the conclusions it has reached and for the recommendations it has based upon these than for the admirable exposition which it affords of the law concerning mining subsidence and of the legal status of the person who has suffered damage by reason of such subsidence, as also of him whose working has caused the damage. The Commission was appointed by Royal Warrant in the middle of 1925 and delivered its final report in the middle of 1927. The terms of reference to the Commission were as follows: "To consider the operation of the law relating to the support of the surface of the land, and of buildings or works on or under the surface, by underlying or adjacent minerals; to enquire into the extent and gravity of the damage caused by subsidence owing to the extraction of minerals and the incidence of the resulting liability; and to report what steps should be taken, by legislation or otherwise, to remedy, equitably to all persons concerned, any defects or hardships that may be found to arise in existing conditions." Report on the Doncaster Area The Commission submitted an interim report at the end of 1925, which referred solely to one area, usually spoken of as the Doncaster area, and recommended that a Commission of a more technical character be appointed to investigate this particular case. This recommendation was acted upon, and the Commission thus appointed reported early in 1928. Here it is necessary only to indicate the nature of the special problem that had to be solved, the proposed solution being mainly of local interest. The Doncaster area consists of about 330 sq. miles of low-lying land in the southeasterly portion of Yorkshire and adjoining parts of Lincolnshire and Nottinghamshire. No less than 78 per cent, of this land lies below the 25-ft. contour line, and a good deal is even below high-water level. It includes a large tract of land known as Hatfield Chase, swampy ground which has always been a source of trouble on that account, so much so that in 1626 a Dutchman, Cornelius Vermuyden, was called in by King Charles I to devise and execute schemes of drainage for its reclamation. The entire Doncaster area is

Jan 1, 1930