Search Documents

By R. U. Jackson

FACED with rising costs, the mining industry is looking to new methods and equipment to supply the relief necessary for profitable operation. Conveyor transportation is rapidly taking a superior position to motor tramming in underground mines because of lower installation, maintenance, and operating costs. Haulage is always a critical problem in underground mining. The ease of operation and flexibility of a haulage system can have an important effect on ultimate mining cost. With the average tenor of ores on the downgrade, larger tonnages are required for the same metal recovery. This selection of a tramming system can be the key to a successful, paying plant. Because this shift is being made at an ever advancing rate, it may become necessary to tailor mining operations to the transportation system, rather than to select a haulage system fitting set mining methods. In choosing a haulage system, the relative costs of the various methods are of the greatest importance. Adapting the mine to one or the other type of tramming is not considered in the cost analysis, and very likely would make little difference, outside of location of drifts and raises. In the cost sheet, the problem presents recommendations for a conveyor installation and a comparison of equipment, installation, operation, maintenance, and power costs are made. Under the track haulage estimate, no allowance was made for dumping equipment at the shaft pocket or bin. If this equipment was added to the balance sheet, the additional

Jan 1, 1952

By F. C. von der Weid

THE mining district of São Fidelis, in the northern part of the State of Rio de Janeiro, is situated on the Paraiba River, where it crosses the Serra do Mar (Mountain of the Sea), in the center of a mountainous country having numerous graphitic outcrops. For a long time, these outcrops were irregularly explored by local people, who had little means and no technical advice. A few years ago, the Cia. Brasileira de Mineração de Grafite took over the control of some of the more important outcrops and entrusted to me the task of studying the ores and establishing a flowsheet for a pilot plant to be situated in Sao Fidelis-the ore to be concentrated being mostly of a very high grade. MINERALIZATION AND ORES The rocks of the district are mostly gneiss and crystalline schists, with occasional interstratification of dolomitic limestone belonging to the Archean Brazilian Fundamental Complex. The general direction of the beds is roughly between 60° and 80°E., with variable dip, generally nearly vertical. Mostly, direction and dip of the graphitic outcrops is concordant with the embanking gneisses or schists. These outcrops seem to be aligned in two or three parallel zones (Pádua, São Fidelis, Macabú), the São Fidelis zone being the best known and the most important to date. Two outcrops of the São Fidelis zone, Saudade and São Benedito, are now being exploited. Mining has been carried out, so far, on a small scale. The mineralization consists of a vein of nearly massive graphite in a very compact, partially granitized gneiss, with vertical dip. The vein is most irregular, with nests and lenses irregularly distributed along the fracture plane. The ore consists chiefly (particularly in São Benedito) of massive graphite appearing and disappearing along the main direction of the vein, forming a succession of irregular lenses in a sort of rosary design. The average width is more or less one foot, with variations from zero to 6 feet. The lode minerals are quartz, a little feldspar and garnet (the latter having its origin perhaps in the embedding gneisses), with rare ferruginous clays on the outcrops. In Saudade a little pyrite, pyrrhotite and chalcopyrite is found occasionally, as well as a carbonaceous mineral, very light, black and shiny, with conchoidal fracture, looking like a sort of jet. The composition of this mineral has not yet been established, but it seems to be very complex. The mineralization seems to be hydrothermal at a rather low temperature, perhaps mesothermal. The paragenesis, according to samples from Saudade, seems to be as follows, the earlier minerals being listed first: pyrrhotite, pyrite, chalcopyrite, with quartz concomitant to the three and

Jan 1, 1946

By G. Sachs, Jr. Brown W. F., Ebert L. J.

It is a generally recognized fact that a steel quenched from the austenitic range and tempered to yield a structure composed of tempered martensite becomes increasingly more ductile with increasing tempering temperature. However, the conventional tensile test fails to yield any value that is sensitive to differences in behavior on tempering among the various low-alloy steels or among different heats of a particular steel. The notched impact bending test, on the other hand, has been recognized for a considerable length of time as capable of revealing differences in impact properties among various steels tempered to 'the same strength level (i.e., the same tensile strength in a conventional tensile test). However, this test is very complex and its significance has not been clarified up to the present time. Of its three characteristic features—the high speed, the notch, and the bending—the notch has been found by Davidenkov2 to be the most potent embrittling factor. Recent investigations on low-alloy steels have shown static notch-bar tensile tests to be more lucid and to evaluate the metal properties in much the same manner as impact tests. In an attempt to analyze the fundamental nature of this test, it was found possible to separate the effects of the two basic characteristics of the stress pattern introduced by the presence of a circumferential notch, the stress state and the high initial stress concentration at the notch bottom. The major conclusions drawn from these previous investigations were as follows: I. The magnitude of the triaxiality at fracture depends primarily on the initial notch depth. Its effect is a great reduction in the average ductility (contraction in area at fracture in the notched section) as compared with that observed in uniaxial tension. This triaxial stress state occurs at a point in the interior of the notch specimen. It determines the notch ductility if the notch is mild and/or the metal possesses a considerable ductility. On the contrary, brittle specimens probably fracture on the metal surface (at the notch bottom) at which point biaxial stress state is present. This biaxiality also considerably reduces the ductility of the metal. For small notch ductilities the notch strength and the notch ductility become very sensitive to embrittling factors. This is contrary to the behavior. of the ductility values derived from a conventional tensile test, which are comparatively insensitive.

Jan 1, 1947

By Ebert L. J., G. Sachs, Jr. Brown W. F.

It is a generally recognized fact that a steel quenched from the austenitic range and tempered to yield a structure composed of tempered martensite becomes increasingly more ductile with increasing tempering temperature. However, the conventional tensile test fails to yield any value that is sensitive to differences in behavior on tempering among the various low-alloy steels or among different heats of a particular steel. The notched impact bending test, on the other hand, has been recognized for a considerable length of time as capable of revealing differences in impact properties among various steels tempered to 'the same strength level (i.e., the same tensile strength in a conventional tensile test). However, this test is very complex and its significance has not been clarified up to the present time. Of its three characteristic features—the high speed, the notch, and the bending—the notch has been found by Davidenkov2 to be the most potent embrittling factor. Recent investigations on low-alloy steels have shown static notch-bar tensile tests to be more lucid and to evaluate the metal properties in much the same manner as impact tests. In an attempt to analyze the fundamental nature of this test, it was found possible to separate the effects of the two basic characteristics of the stress pattern introduced by the presence of a circumferential notch, the stress state and the high initial stress concentration at the notch bottom. The major conclusions drawn from these previous investigations were as follows: I. The magnitude of the triaxiality at fracture depends primarily on the initial notch depth. Its effect is a great reduction in the average ductility (contraction in area at fracture in the notched section) as compared with that observed in uniaxial tension. This triaxial stress state occurs at a point in the interior of the notch specimen. It determines the notch ductility if the notch is mild and/or the metal possesses a considerable ductility. On the contrary, brittle specimens probably fracture on the metal surface (at the notch bottom) at which point biaxial stress state is present. This biaxiality also considerably reduces the ductility of the metal. For small notch ductilities the notch strength and the notch ductility become very sensitive to embrittling factors. This is contrary to the behavior. of the ductility values derived from a conventional tensile test, which are comparatively insensitive.

Jan 1, 1947

By GUY C. RIDDELL

ZINC, manganese, and aluminum received attention at the two nonferrous metallurgy sessions at the Annual Meeting. L.P. Davidson, general superintendent of the rebuilt Monsanto zinc plant, described its operation, which reflects Polish practice and is really a combination of electrolytic, Waelz, and retort procedure. Briefly, it embraces leaching of roasted concentrate with sulphuric acid, electrolysis of sulphate solution using Tainton lead-silver anodes with ?goulac? added to the electrolyte, treatment of tailing in Waelz kilns, and retorting of the recovered zinc oxide, casting furnace dross and residues. Recovery is good, equipment and maintenance costs low. Ferrate zinc that might be lost in the electrolytic process appears to be recovered as oxide in the Waelz treatment.

Jan 1, 1942

By E. A. Beck

(New York Meeting. February, 1913.) For a number of years many attempts have been made to use thermit in order to do away with piping in ingots. Some of these attempts were successful, while others did not give the expected results. Nearly every plant had its own method of using the thermit, and no special care was taken to study, the results or to find the causes for lack of success. Formerly the principle of the process was to decrease the piping by introducing a can filled with thermit, attached to an iron rod, into the head of the ingot directly after it bad been poured. In this case the thermit reaction took place in the upper part of the ingot, and it was thought that through the heat produced the head would keep liquid longer and piping thus be reduced. In other words, the aim was to keep the head of the ingot open by making use of the heat of the thermit reaction, which would thereby give the gases in the steel sufficient time to escape. This result can be attained by the application of a large enough quantity of thermit, but it would not be economical in general practice, and could only be used for high-grade material. Many steel-makers abroad and in this country have had this experience. The Th. Goldschmidt A. G., Germany, has, therefore, made a special study of this question with the co-operation of a well-known steel company, and has worked out a new method for. the application of thermit for this purpose. The results obtained have been most satisfactory and reliable, and this- process is now used in Germany on a large scale in many prominent steel-works.

Jan 4, 1913

By G. S. Morison

I have bad considerable experience with the testing-machine at the Watertown Arsenal, having had broken there sixteen large steel eye-bars, besides quite a number of iron bars and two compression members. So far as accurate mid satisfactory results are concerned, the machine is all we could ask for, and the officers who have it in charge, together with their civil assistants, are thoroughly conversant with it 1 details, and entirely competent to make the tests required. The principal defect is that the force is very inadequate. As the machine is arranged, tile weighing apparatus is at one end and stationary, the measure of strain being carried from this to the scale-beam by the fluid in a tube m small that it looks like a wire. At the other end is placed the hydraulic press by which the power is applied; this press is mounted on a small carriage and held by two eight-inch screws about four feet above the floor, which arc of course strained in compression during tensile tests, and in tension during' compression tests. When the stretch of the material has exhausted the throw of the plunger it is necessary to relieve the strain, draw back the plunger, and move the carriage along, which is done by nuts turned by steam working on the large screws. Every specimen placed in the machine must be lifted above the large screws and lowered into position. To do this, crabs, running on travellers, which span the entire room, are placed over the machine, and by these the specimen can be lifted and put in place. The actual time required to make a test depends largely on the amount which the material stretches, bat it may generally be said, that for specimens which will stretch from two to three feet the

Jan 1, 1882

Technology has no recognized rank in what is called polite literature; the subject-matter of engineering is not supposed to lend itself to artistic treatment; we are the hewers of wood and drawers of water to the high-priests of learning that live on the cold summit above our humbler dwellings. Therefore the hierophants smile at the notion of 'style'- “that curiously personal thing”--in technical writing. The "great art" of Pater, the "inevitable phrase" of Raleigh, the "note of distinction" that Arnold demanded are said to be beyond the scope, as they are supposed to be beside the need, of a writer on geology or engineering. This is a narrow view. Science, no less than belles lettres, calls for the best exercise of the human intelligence; the art of writing should be employed as skilfully and as earnestly in a description of the structure of the Sierra Nevada, or of the construction of a tunnel through the range, as in a rhapsody welcoming the rosy fingers of the dawn. The idea still lingers that fine writing does not befit technology, even though the masters of the Victorian period- Huxley, Tyndall, Ruskin-proved that science is worthy to be arrayed in the best robes that the looms of thought can weave. At the beginning of these lectures I quoted Barrie's remark touching the inability of the scientific man to express himself. That imputation has been passed to the technologist, whose utilitarian pursuits are supposed to make him too clumsy for the refinements of human speech. We may not have acquired the self-consciousness of those writers on Art whose "power of expression is so cultivated that their sensual caterwauling may be almost mistaken for the music of the spheres"; nor can we imitate the politicians, who have the ability to speak far beyond anything that they may have to say; but we too have a litera-

Jan 1, 1931

By H. E. Rowen

As high grade iron ore deposits dwindle and costs rise, sintering becomes more and more important. The steel industry is now faced with beneficiation problems once peculiar to nonferrous work. Succeeding articles describe recent advances in this field. Here is presented the first chapter of a history still being written. SINTERING, for the purpose of this discussion, is defined as the art of burning a solid fuel with 90 to 95 pct ash content. Considering problems of combustion involved in keeping a home furnace burning properly with 12 to 20 pct ash in the fuel, it is evident that combustion represented by the definition has to be right or nothing is going to happen. Our forefathers discovered that many ores containing metals essential to the steadily rising standards of living were associated with elements such as sulfur and arsenic, which had to be removed before refining. This they did by utilizing the solid fuels they had available-the sulfur or other readily combustible components-to create roasting heat. One of the early methods is demonstrated in an old woodcut of the roast heap, Fig. 2. Ore was broken into chunks, piled on an ignition layer of solid fuel-logs in this case-and then. ignited. The sulfide ores roasted as the sulfur burned out. As shown in the background, the countryside was rapidly denuded of all vegetation by the great quantities of SO2 and other liberated gases.

Jan 1, 1961

By Ralph Hultgren

FEW phase diagrams of alloys composed of two transition metals have been adequately studied, probably because of the high melting points involved. Transition metals are the elements that have inner shells incompletely filled with electrons. They comprise groups IIIa to VIIIa of the periodic table, including more than half of all metals. We have chosen to study two systems whose comparatively low melting points allowed the alloys to be melted in a molybdenum resistance furnace. The nickel-palladium system proved to consist of a simple series of solid solutions, but iron-palladium manifested several remarkable features. The main characteristics of the latter diagram were decisively established, but lack of time prevented precise determination of phase boundaries. The gamma to alpha transformation in this system is unusual and warrants further study. Grigorjew1 determined the liquidus and solidus of the iron-palladium system by thermal methods. He found a minimum melting point, but no eutectic. He also found that palladium lowered the gamma to alpha and raised the gamma to delta transformation temperatures of iron, with a complete series of solid solutions existing between gamma iron and palladium. His measurements also indicated a compound or super-lattice near the composition FePd3. Jellinghaus2 found that annealing at 500° C. greatly increased the magnetic coercive force of an alloy of composition FePd. X-ray dif-fraction photographs showed that a tetragonal ordered phase had formed during the anneal.

Jan 1, 1939

By Edward Halse

The tin-deposits of Durango, Mexico, have been ably described by Mr. W. R. Ingalls in a paper published in our Transactions in 1895.* While the occurrellces of tin-ore in other parts of the Republic are similar in many resperts to those in Durango, there are noteworthy local differences which, it is hoped, ma? lend interest to the present paper. The deposits examined by me in May, 1895, are found in the Serrania de Chacuaco, Municipality of Sain Alto, District of Sombrerete. The workings are situated in a range of mountains having a general northwest to southeast trend between Sombrerete and Fresnillo; the most northerly claim (La Desparranlada) being about six leagues southeast of the former town. El Refugio lies about four leagues to the southwest, and El Calabrote eight leagues to the west, of Fresnillo. The claims are from about 8425 to 8775 feet above sea-level, and from 1500 to 1800 feet above Sain Alto, the position of which town is marked in the map printed in Mr. Ingalls's paper. In order to reach the claims, one uses the carriage-road from Sain Alto to the small tin-colony of Las Cuevas; from the latter place to the mines there is only a rough mule-track. The mountain range consists of a rugged, weathered, gray granite rock, remarkable for large grains of quartz, and is flanked by masses of rhyolite and rhyolite-tuff of upper Tertiary age. The whole formation is broken up by narrow and steep willding arroyos and deep barrancas, mainly the result of denudation, and it appears to be a southeasterlj extension of the tin-bearing belt of rocks north of Durango City. Here and

Jan 1, 1900

By K. Heindlhofer

ESTIMATES of the "plasticity" of a metal are commonly deduced from three types of test-tensile, torsion and impact. The several results have been more or less at variance, though this disparity has attracted little notice, largely perhaps because they have been expressed in different terms. The discrepancy between the results of the three tests becomes obvious when each is made at a series of low temperatures, for the temperature range within which the "plasticity" of iron largely disappears proves to be very different in the three types of test. The rather abrupt disappearance of "plasticity" of iron within a narrow temperature range cannot be due to any physicochemical change (such as a precipitation) taking place in the material at that time, because the original plasticity is immediately regained when the temperature of the material is brought above the sensitive range. Accordingly this differ-ence in behavior shows that the "plasticity" of a metal depends upon the mode of action of the stresses which produce the deformation, and there-fore upon the method of test. Analysis of the stresses leads to the conclusion that the observed plasticity of a metal is determined by the relation between its resistance to rupture by separation and its resistance to shear (slip), on the one hand, and between the effective normal and shearing stresses on the other; and that the relation between the two resistances does not in general remain constant with change of temperature, and may somehow be altered to some extent by the previous treatment of the specimen. This suggests the view that the results of none of the usual mechanical tests are directly comparable even for a single metal tested at a series of tem-peratures, or for a series of metals at one temperature, because the propor-tion of the total resistance of the metal to the test contributed by the

Jan 1, 1934

By Tribhawan N. Srivastava

The Henderson Mine started production in 1976 utilizing a unique, push-pull, mine ventilation plan. As the mine expands in size, the mine ventilation requirements will increase and a more comprehensive system for maintaining ventilation will be needed. A computer simulation study was completed and has resulted in a revised, systematic, mine ventilation plan which is being implemented as mine development proceeds. Based on the computer simulation study, the new ventilation plan takes into account mining of the orebody simultaneously from both the 8100 and 7700 production levels. Present experience and empirical data indicate that volumes of air needed to adequately ventilate both production levels cannot be obtained utilizing the existing mine layout. The total volume of air needed for the mine excluding haulage tunnel will increase from 708 m3/s (1 500 000 cfm) to 1652 m3/s (3 500 000 cfm), thus a new No. 5 exhaust shaft and connecting drifts are being developed to expand the mine ventilation system to service both production levels. The original ventilation plan for the 7500 haulage level was to bring air from the No. 2 and No. 3 intake shafts and exhaust it through the 94X raise to the 8035 exhaust level and then through the No. 1 exhaust shaft to surface. Control of air volumes in loading drifts was initially planned to be achieved by air doors and air curtains. Air doors on the 7500 level require large cutouts, expensive installations and constant maintenance. The computer simulation study indicates that air- flow in the 7500-level production drifts can be con- trolled exclusively by air curtains which are less expensive to install and more effective in regulating airflows than air doors. Air from the 7500 level can be exhausted through a new raise to the new 7635 exhaust level and then through the new No. 5 exhaust shaft.

Jan 1, 1982

By L. S. Reid

THE study of the flow of oil and gas mixtures through oil-bearing formations has received special attention from the petroleum industry within the past few years, and has resulted in a series of research projects based upon various phases of the flow of heterogeneous fluids through porous media. Obviously, the low cost of producing oil during the flowing life of a well makes it desirable to obtain production by natural flow as long as possible and to effect a maximum recovery of oil and gas by the utilization of reservoir energy through efficient methods based upon a thorough knowledge of reservoir characteristics. Despite the extensive research that has been carried out, there is little information available on the behavior of oil and gas mixtures flowing through reservoir formations. This makes it impossible to predetermine the optimum operating condi-tions for flowing wells. A differential pressure must exist in the reservoir in order to induce flow toward the well. It is a well established fact that with homogeneous fluids the relation of pressure drop to linear distance traveled is a straight-line function as long as the flow is viscous. However, in regard to gas-saturated oils, a number of investigators1,3,4 have reported that the flow characteristics are materially altered as some of the lighter hydrocarbons are liberated from the oil to form gas while the fluid passes through the reservoir. Most of the work done has been concerned primarily with steady-state flow of liquid-gas mixtures. Cloud1 has studied the effects of saturating crude petroleum oils with various gases, together with the resultant pressure gradients under steady flow conditions, noting that unsaturated oils flowed faster and yet maintained lower pressure gradients than saturated oils.

Jan 1, 1938

By Donald Barton

THE purpose of this torsion balance survey and the quantitative calculations was to delimit the extension of the cap rock at the Hoskins Mound salt dome. The sulfur ore in the Gulf Coast sulfur-bearing salt domes occurs in the lime rock, which is the outer layer of the cap-rock mass, and also in the underlying gypsum zone. The status of the exploration and exploitation of the Hoskins Mound dome at the date of this survey is shown by Fig. 1. The mound had been covered by the very early prospect wells of the Mound Oil Co., and the later and more numerous prospect wells of The Texas Company. The Freeport Sulphur Co. was producing from the flank wells in the southwest quadrant. The limits of the cap were surmised to lie inside the centers of quad-rangles 4F, 3F, the center of the NE. ¼ of 2E, and the north line of 2D. That surmise was based partly on the data of Fig. 1 and partly on the position of the edge of the topographic mound. The management of the Freeport Sulphur Co. wished to block out the extent of its ore reserves with a minimum of expenditure. The management was informed by the writer that no geophysical method could map the presence or quantity of sulfur directly, or determine the presence and quantity of the lime-rock cap independently of the rest of the cap, but that a reasonable probability existed that the approximate position of the edge, the depth and the thickness of the cap-rock mass as a whole could be determined through quantitative calculations based on the data of a very careful torsion balance survey. Considerable lime rock would probably be present, of course, wherever much cap rock was present. This paper presents the data of the survey, our calculated prediction of the configuration of the cap rock, and the degree of confirmation by the subsequent drilling. The survey was made by the Geophysical Research Corporation, under the direction of the writer. The work of the calculations was done by Andrew Gilmour, then assistant to the writer.

Jan 1, 1936

By Eugene S. Perry

The most outstanding event in oil and gas development in Montana during 1936 was the discovery of oil in the Baker-Glendive gas field, in the extreme eastern part of the state. Other notable achievements were small extensions in the Cut Bank oil field; continued favorable results of acidization in the Kevin-Sunburst oil field; and the discovery of oil and gas in commercial quantities about 20 miles southwest of Billings, on what is known as the Mosser dome. Several wildcat wells were drilled. For the coming year of 1937, it is anticipated that the main activities will be confined to drilling in or near known fields. During 1936 Montana had seven fields producing oil, but over 95 per cent of oil production came from four fields, which in order of importance are: Cut Bank, Kevin-Sunburst, Cat Creek and Pondera. Total production for the state was 5,850,893 bbl., which is 1,251,761 bbl. more than the total for 1935. Natural gas was produced and marketed from eight fields, most important being Cut Bank, Baker-Glendive, Kevin-Sunburst and Dry Creek. These four fields accounted for over 85 per cent of total state gas production, which is slightly greater than the 1935 production of nearly 18 billion cubic feet. Increase in gas consumption is due in part to increase in smelter operation. More detailed information pertaining to the various fields is given in Table 1. In the Baker-Glendive field a test 8186 ft. deep, 15 miles southeast of Baker, was completed by the Montana-Dakota Utilities Co. in 1936. The first gas-bearing sandstone (Judith Hiver horizon, Upper Cretaceous) was found at a depth of 528 ft., and a second sand at 1167 ft. Sandstones of the Dakota formation, in which occurred water, were found from 3724 to 3853 ft. White sandstone correlated with the Tensleep (Minnelusa) formation of Pennsylvanian age was found from 5631 to 5751 ft. deep. The lower 1900 ft. of the well (below 6278 ft.) was essentially in limestone and dolomite, and information on correlation of formations in this mass of sediments is not available at this time. The upper portion of this part of the well contained much anhydrite. Cherty and dolomitic limestone below 7000 ft. may be equivalent to limestones of the Madison formation. The thickness of strata beneath the Dakota formation was

Jan 1, 1937

By R. C. Edwards, Will Mitchell, T. G. Kirkland

THREE years ago, when the Process Research Laboratory at Allis-Chalmers Manufacturing Co. sought a remedy for the increasing cost of disposing of great quantities of spent sands from foundries, R. C. Edwards developed a continuous inclined paddle scrubber which removed a substantial amount of the charred coatings from the grains with a surprisingly small amount of degradation of the sand itself.1 The satisfactory results obtained on foundry sand, using this piece of equipment in conjunction with classification, suggested that a similar procedure could probably be applied to the cleaning of other sands, such as those required by the glass and chemical industries. This paper describes the flowsheet and the results of tests performed on impure natural sands. The four materials tested were silica sands obtained from widely separated geographical areas. Three of the sands tested contained various amounts of iron oxide and the fourth an excessive amount of calcareous bonding material. The iron oxide was present predominantly in the form of grain coatings, which were scuffed by the paddle scrubber, and in all cases a product was manufactured which would meet one of the sets of specifications imposed by the glass industry' The Edwards paddle scrubber used in these tests consists of a rubber-lined steel cylinder 18 in. in diam and 48 in. long, mounted on a frame so that its slope can be varied 5 ° to 35º from horizontal. This variable slope permits controlled flow of material through the machine. Rubber paddles rotate inside the cylinder and are secured to a center shaft 2 in. square, which extends through the entire length and is turned at both ends so that it can be supported by sleeve bearings centrally fixed in the end plates of the shell. At the upper or feed end it extends through the bearing on the end plate into a sheave, to which the motor drive is connected by means of Texrope transmission. The four sets of paddles mounted on the shaft, two in each set, are made of rubber belting, 1/4 in. thick, 9 in. wide, and 16 in. long. The two paddles in each set are secured on opposite sides of the square shaft, but in the same longitudinal position along the shaft axis. In other words, the two paddles in the set operate 180° apart. Each successive set is mounted 90º from the preceding one. One end of each paddle is bolted to the square shaft and the other weighted by a steel bar, 1x1 ½ x9 in. long, which is attached about 1/ 2 in. from the outer tip of the paddle. By centrifugal force at proper shaft speed, these weights force the paddle surface to rub smoothly against the rubber lining of the cylinder. During operation, the sand forces its way between the paddle face and the surface of the cylinder, providing the necessary abrading action as the pulp flows by gravity down the length of the cylinder. The capacity of the machine is limited by the amount and the hardness of the coating material and by the quality of product desired. The degree of scrubbing is governed by the retention time in the scrubber, which in turn may be changed by varying the feed rate, water content of the feed, and

Jan 1, 1952

In 1820, the Board of Public Works was considering some improvements to the canal, in order to reduce the cost of transportation, and in its annual report for that year gives a description of the method of loading the coal from the pit to the boat, and also from the boat to the dealer's yard, which is illuminating in showing how coal of this type should not be handled. It follows:- "It will be seen by the estimates, that the improving the present canal, forming a canal of large dimensions, from the head of the present lower canal to Sabbot Island; erecting locks of large capacity, and making a communication with the river, so as to completely accommodate the coal trade, (except it should hereafter be found necessary to make another communication with the river,) will not cost more than 126,000 dollars. But as there is some doubt whether the streams that may be received into the canal between Sabbot Island and the upper arch, will at all times be competent to supply the locks on that portion, we will extend our calculation to a point nearly half a mile above Pleasants' Island; where, by erecting a dam, any desired quantity may be thrown into the canal. This extension of the canal with one lock, and the dam across the river, is estimated at 34,000 dollars, making in the whole a little over 160,000 dollars. There will then remain a surplus of 40,000 dollars after completing the works to the point last mentioned. "In order to discover what effect the improvement of this first section will have on the tolls, it will be necessary to take a view of the present state of the coal trade, and endeavor to ascertain what change will result from the increased facility of transportation. "That part of the business which is carried on by water, is conducted nearly in this way. When the coal is drawn out of the mines, it is thrown in a heap near the mouth of the mine, or shaft; it is then loaded into carts, and carried to the river bank, where, in some instances, it is discharged from the cart at the brow of the bank, and runs down to the beach near the water's edge; then shovelled into wheel-barrows, and wheeled aboard of the boat, and discharged from the barrows by upsetting. In other instances, the carts are driven on to a kind of scaffold, furnished with a wide spout or director at the edge; by which the coal is conveyed immediately into the boats. These boats are the common James river poplar batteaux, and require three men to each. The up-stream navigation being laborious, the boats are built of light materials, and continue fit for service but a short time, (say) from two to three years; their cost, when new, from fifty to one hundred dollars. "When the river is tolerably flush of water, one of these boats will carry about two hundred bushels; but in low water their load is sometimes diminished to one hundred, and even as low as eighty bushels. They pay for passing the canals and locks to the Basin, one dollar per load; so that when full loads are taken, it will amount to half a

Jan 1, 1942

By Lynn Howell

IN a previous articles we have described a technique for measuring the relative intensities of gamma rays from the radioactive elements occurring naturally in geological formations along the walls of a borehole. The apparatus consisted of two Geiger-Müller tubes mounted inside a pressure-tight chamber. Each counter tube was coupled separately to an amplifier and a frequency meter at the surface by means of a multiconductor cable upon Which the chamber was suspended. The output currents of the two frequency meters were recorded on a photographic paper as the chamber was moved in 'the hole. These traces showed remarkable correlation with the geologic formations, as evidenced by comparison with commercial electrical logs.' Owing to the penetrating power of the gamma rays, logs may be taken in both open and cased boreholes. The apparatus has recently been changed somewhat. One of the counter tubes has been removed and a stage of amplification has been added. inside the chamber, This arrangement seems to give a more favorable signal-to-noise ratio and satisfactory logs can be now made in cased holes and also in open holes as previously, Briefly described, the chamber moving in the hole is made of 3,2-in. drill pipe and is about 10 ft. long. There is an additional extension about 2 ft, long at the top, inside which cable connections are made. The Geiger-Müller tube is mounted inside the bottom end of the chamber, Above this is the vacuum-tube amplifier with its batteries and transformer, In the top part of the chamber, small 45-volt batteries are mounted, which in part supply the high voltage for the counter tube, Additional voltage is supplied from the surface through the multiconductor cable upon which the chamber is suspended. Also, the output of the transformer in the single-stage amplifier is coupled to another single-stage amplifier at the surface through this cable. The surface amplifier is coupled to the Thyratron-controlled frequency meter, the tank circuit of which consists of a one megohm resistor across which is a bank of condensers varying in

Jan 1, 1939

By Leland Van Wert

IN 1888, Howard,1 working at the Watertown Arsenal on the tensile properties of ferrous materials at various temperatures, noted the curious fact that the stress-strain diagrams of low-carbon steels tested within a certain temperature range (200° to 350° C.) departed more or less from the normal regularity of such diagrams as secured by testing at either above or below these temperatures. This same jagged appearance of similar diagrams for steels has been observed by at least one other investigator, and de Forest2 has reported similar irregularities in the tensile testing of some nonferrous alloys. Recently again, this anomaly in diagram contour has been shown in a most striking fashion, apparently because of its accentuation by the method of testing employed, by Dr. Albert Sauveur.3 He described (for nonaustenitic steels) two quite distinct types of torsional stress-time diagrams: (1) those with a regular and smooth outline, derived normally by testing at temperatures above 300° C., or below 200° C. (as, for example, Figs. 4a or e); and (2) those presenting a decided "stepped" appearance, which are invariably produced when twisting is done within the 200° to 300° C. range (examples, Figs. 5a and b). The torsion test brings out so much more sharply (and convincingly) the irregularities occurring at 200° and 300° C. than does the tensile test that they can no longer be considered as resulting from simply idiosyncratic or accidental and inconsequential causes. Clearly, from the temperatures involved, the "stepped" type of diagram, or more accurately, the peculiar manner of response to torsional stress which manifests itself in the diagram, is an aspect of the "blue-heat" phenomenon. One's curiosity if, nothing else, prompts an inquiry as to the nature and significance of these "steps." What do they mean? What causes them? To these questions there are no completely satisfactory answers. The following experimental observations are offered as suggestions towards the solution of the problem.

Jan 1, 1931