Search Documents

By Edward A. Sayre

In shaft sinking for cod mines, the cost item greatly influences the method adopted. This holds true especially when soft material must be traversed. The average life of a coal mine is short. This is due either to the limited area of the coal basin or to the great expense of maintenance and haulage underground when the entries are extended a considerable distance from the hoisting shaft. Therefore, the engineer in opening a coal mine is confronted with the fact that the cost must be kept within certain bounds else the venture will prove unprofitable. For this reason he may be prohibited from adopting certain safe, but expensive, methods that are used in sinking caissons for foundations, driving transportation tunnels, or other work of permanent construction. A common method of sinking through difficult ground employs the aid of a steel shoe pushed ahead of the shaft timbers. Another is the drop-shaft method. These two methods were used in sinking the main shaft and the air shaft of the Eagle No. 3 mine, at Des Moines, Ia., and the following data show the relative success and cost of the two methods of sinking under the same conditions. A drill log of the material to be penetrated was as follows (see Plate 1, Fig. 1): Thickness, Total Depth, Ft. In. Ft. In. Drift................................... 38 38 Sand..................................... 2 40 Drift.................................... 2 6 42 6 Jointed clay.............................. 5 6 48 Drift, firm............................... 10 6 58 6 Clay, with sand streaks.................... 3 61 6 Sand.................................... 12 73 6 Shale, with two thin beds of coal and thin strata of rock......................... 86 6 160 Rock.................................... 5 165 Coal..................................... 3 9 168 9 Main Shaft Sunk by Steel-Shoe Method This record shows the first 73 ft. to bc of drift material, the lower 12 or 15 ft. of which was sand. The remaining 92 ft. to the coal was shale and rock, and offered no trouble in sinking.

Jan 1, 1917

Jan 1, 1902

By T. J. Smolik, Harman, D. W. Fuerstenau

By means of electrokinetic measurements, the surface properties of the aluminosilicate polymorphs (sillimanite, andalusite, and kyanite) and also mullite have been found to depend on the ratio of A10 bonds to SiO bonds in the surface. The Al-toSi ratio in the surface is dependent upon the crystal lographic properties of the mineral, which in turn determine coordination numbers of A1 and of Si, cleavage characteristics, and density of the various solids. Mullite with a greater bulk Al-toSi ratio has the highest zpc of the aluminosilicates. By treatment in dilute acids or by cycling between acidic and basic solutions, alumina is selectively dissolved from the surface of these orthosilicates. This shifts the apparent zpc to lower pH values as the fraction of SiO groups in the surface increases. Thus, surface properties can be altered by procedures that alter the A l-to-Si ratio in the surface. Flotation of these aluminosilicates results from electrostatic interaction of the collector ions with the mineral surfaces. As a result, flotation response shifts in accord with any shift in apparent zpc by pretreatment. Separation of minerals by flotation is based on differences in the physicochemical properties of their surfaces.'-3 For many minerals, adsorption of flotation collectors results from their functioning as counter ions in the electrical double layer at solid-water interface. In such systems, separation depends on differences in the zero point of charge (zpc) of the various minerals. The zpc is defined as the concentration of potential determining ions in solution at which the surface is uncharged. The potential determining ions for inorganic oxide-water interfaces are hydrogen and hydroxyl.4,5 This work is concerned with the effects of crystal structure, composition, and surface preparation on the surface properties and flotation behavior of aluminosilicates. Differences resulting from crystal structure were studied by measuring electrokinetic potentials and determining the flotation behavior of three different aluminosilicate materials having the same chemical composition (Al2O3 SiO2), namely andalusite, kyanite, and sillimanite. Furthermore, the effect of the Al2O3-to-SiO2 ratio on flotation behavior and surface properties was investigated by including synthetic mullite, 3A12O3 .2SiO2. Gaudin and co-workers 6,7 have clearly shown how crystal structure determines the native floatability of certain minerals. Those solids in which the surface is comprised mainly of broken residual bonds possess naturally hydrophobic surfaces. It was found by Bakakin8 that for a number of oxidized lead minerals, differences in floatability were due to the distance of Pb atom from the surface. Only limited work has been done on relating electrical properties of surfaces to crystal structure and composition. Healy et. a1.9 found that the zero points of charge of various manganese dioxides ranged from about pH 1.5 to pH 7.5, and these differences in the zpc's were interpreted in terms of the atomic packing in the various crystals. The research presented here clearly shows that crystal structure and chemical composition do affect the surface properties of aluminosilicates and, in addition, that these effects can be altered by changing conditions under which the surfaces are prepared. CRYSTAL STRUCTURE OF THE ALUMINOSILICATES Sillimanite, andalusite, and kyanite are composed of regionally metamorphosed rocks differing mainly in degree of metamorphism. All three minerals have the same chemical composition, Al2O3 - SiO2, of which sillimanite is the high temperature polymorph and kyanite and andalusite the lower temperature polymorphs. Andalusite and sillimanite crystallize in the orthorhombic system while kyanite crystallizes in the triclinic system. The structure of these three minerals is essentially chains of aluminum-oxygen octahedra linked laterally by silicon and aluminum. The arrangement of these chains in the three minerals is shown in Fig. 1.l4

Jan 1, 1967

By L. V. Pirela, S. M. Farouq Ali

Some interest has been expressed recently in the application of solvents in conjunction with a thermal drive, such as a steamflood. At least one field project of this type has been reported. This paper makes the first attempt to provide some of the basic information necessary for choosing a solvent for such an application. Results of displacements conducted at elevated temperatures are also discussed. This paper shows that, in the case of alcohol-hydrocarbon-water or brine ternary systems, the system miscibility may increase, decrease, or both increase and decrease within the same system when the temperature increases. The distribution coefficient was consistently found to increase in favor of the oleic phase with an increase in temperature, which is advantageous from the standpoint of oil recovery. Results of solvent displacements in a sandstone core showed that even a relatively small temperature effect in the favorable direction (increase in miscibility and distribution coefficient) can lead to a 50 percent increase in oil recovery. On the other hand, if the system miscibility decreases with the temperature, even though the distribution coefficient increases, the oil recovery at the higher temperature may not increase. INTRODUCTION Miscible displacement has been the subject of many investigations. Miscible-phase solvent flooding, employing solvents such as alcohols that are miscible with both oil and water, has received considerable attention. Investigations conducted by Gatlin and Slobod,l Taber, Kamath and Reed,2 Holm and Csaszar,3 and Farouq Ali and Stah14 have helped in understanding the mechanism of solvent flooding. While the use of alcohols and similar solvents as oil recovery agents is economically unattractive, these solvents nevertheless provide a means of understanding the mechanistic aspects of important miscible-phase oil recovery processes such as the Maraflood process (discussed by Gogarty5). As shown by Taber et a1.,2 the phase behavior of a solvent-oil-water system is of .utmost importance in determining the efficiency of the oil displacement. This paper makes the first attempt to obtain the ternary phase behavior data for nine alcohol-hydrocarbon-water/brine systems at elevated temperatures. Results of core tests at elevated temperatures are also presented which corroborate the effect of temperature on oil recovery, as judged on the basis of phase-behavior data. The use of solvents at elevated temperatures has been suggested earlier by Farouq Ali.6 At least one field test of this type has been reportedO7 With the widespread use of thermal recovery techniques, it is possible in some situations (especially in steamflooding) that the use of a suitable solvent in conjunction with the heat carrier may be economically feasible. This paper attempts to provide some of the basic information needed for judging such feasibility. LOCATION OF THE PLAIT POINT The phase behavior of a typical ternary system consisting of a solvent, hydrocarbon and brine (or water) can be represented by a triangular diagram such as the one shown in Fig. 1 (for temperature TI). Point Pon the binodal curve represents the plait point, being the limit of tie lines such as Y1 Y2 The compositions of the coexisting oleic and aqueous phases are given by points Y2 and Y1, respectively, for any mixture composition along Y1Y2. The characteristics of ternary diagrams have been discussed by Findlay8 and others. Taber et aL3 have shown that the position of the plait point in a particular ternary system plays the decisive role in determining whether or not theoleic phase would be displaced in a continuous manner during an alcohol displacement. The area above the binodal curve also is important, since it represents

Jan 1, 1969

By D. E. Light, J. Y. Somnay

The use of alkyl acid phosphates and their alkali salts as collectors for the uranium minerals brannerite and uranothorite was investigated. In particular a detailed flotation study was carried out using isooctyl acid phosphate as a promoter. Tests were conducted on an Elliot Lake ore analyzing 0.11% U 3 O 8, chiefly as brannerite, and approximately 9% pyrite. Pyrite was floated with conventional reagents; the flotation of brannerite from the sulfide tails was studied to determine the optimum pH and pulp density to employ with isooctyl phosphate. 4 uranium recovery of over 90% was possible with a selectivity index of 8.95 when these tails were floated at 17% solids and a pH of 1.7. The effect of various modifying agents was also investigated. Aluminum sulfate, lactic acid and sodium silicate improved the selectivity of collection yielding selectivity indices of 9.5 to 11.5. Ferric chloride was found to be a depressant for brannerite. A Bancroft ore which analyzed 0.13% U308, and contained uranothorite was also amenable to flotation using isooctyl acid phosphate. The composite uranium concentrate obtained assayed 0.41% U308 at a recovery of 95.3% and a ratio of concentration of 3.24. Previous investigations1,2 on the flotation of brannerite, pitchblende, uraninite and/or uranothorite from various Canadian ores showed that fatty acids, including oleic acid and tall oils, petroleum sulfo-nates and alkyl acid phosphates, were suitable collectors for these uranium minerals. Additional work carried out by the Mines Branch in Ottawa on brannerite ores from the Elliot Lake area3 used the tall oil Acintol FA-1, or FA-2, as a collector. A recovery of 92% of the uranium in a concentrate which contained about 55% of the weight and assayed 0.2% U3O8 was obtained from a feed of 0.1% U308 in this latter instance. Eigeles et a1.4 carried out flotation on pitchblende ores and found that the most promising results were obtained with alkyl acid phosphates and their alkali salts as collectors. Within the homologous series of alkyl phosphates, the best flotation characteristics were displayed by isooctyl phosphates. Further, isooctyl phosphate derivatives were much less sensitive to hardness forming salts than oleic acid, enabling all flotation tests to be made with tap water. This paper describes tests employing alkyl acid phosphates for the flotation of ores containing brannerite and uranothorite. The flotation work described herein was conducted in conjunction with the development of a leaching process for Elliot Lake, Ontario, brannerite ores. In this process pyrite in the ore was concentrated by flotation and roasted, providing sulfur dioxide which was used to produce sulfuric acid in situ in a liquid-solid extraction process. A 40% conversion to sulfuric acid was indicated at a leaching temperature of 80°C; this resulted in the extraction of 93% of the total uranium after a contact period of 6 hr. A rotary kiln was used as a leaching vessel. Preconcentration by flotation was studied in conjunction with the above process to reduce the bulk of solids for leaching and, consequently, capital expenditure. The materials and methods used in this study will be described initially. Then the results will be presented in two sections, the first dealing with the brannerite ore, and the second with the uranothorite. Finally an economic analysis of the results on the brannerite material will be made. MATERIALS AND METHODS The two ore samples examined were from uranium-producing mines. One was a brannerite ore, a uraniferous quartz pebble conglomerate from the Elliot Lake area, which contained 0.11% U3O8, 4.3% S and 4.5% total Fe. Mineralogical studies of similar samples indicated the presence of quartz, microcline, sericite, pyrite and minor quantities of rutile, pyrrho-tite and zircon. The other ore was from a biotite-rich pegmatite in the Bancroft area; feldspar, quartz and biotite formed the major gangue components. Uranothorite was the principal uranium mineral; the head assay was 0.13% U 3 O 8. Preparation of Feed: The ores were crushed to —10

Jan 1, 1963

By AIME AIME

THE 129th meeting of the American Institute of Mining and Metallurgical Engineers convened at New York City, in the Engineering Societies Building, Feb. 18-20, 1924. On February 21 an excursion was made to the Bethlehem Steel Co., at Bethlehem, where about 200 members and guests were splendidly entertained. An illustrated description of the Bethlehem Plant will be published next month. The meeting and excursion were largely attended; the registration at New York totalled 1276 versus 1201 in 1923. William Kelly, long identified with the iron-mining industry of the Lake Superior district, was elected President of the A. I. M. E. for the coming year, at ,the annual business meeting, Feb. 19, succeeding E. P. Mathewson. The following Directors were also elected (the date signifies year of termination of office; the final figure indicates the "District" the Director represents).

Jan 1, 1924

By R. W. Heckel, R. A. Tanzilli

Treatment of the finite, diffusion-controlled, two-phase, moving-interface homogenization problem has been carried out by numerical methods for a wide range of input parameters. Solutions have been obtained for planar, cylindrical, and spherical diffusion geometries. The effects of parameters such as the interdiffusion coefficients (concentration-independent) of- both phases, the concentrations (time-independent) of each phase at the interlace, mean composition, initial size of the dissolving- phase, and initial composition of- the two phases are considered. The results are displayed to show both the position of the interjace and the degree of homogenization (expressed in terms of concentration at the matrix phase symmetry boundary) as a function of diffusion time. Typical exaw~ples to which the results may be applied are discussed. A limited number of exact, closed-form solutions to the multiphase, diffusion-controlled, moving-interface problem exists in the literature, e.g., Refs. 1 to 7. The exact, closed-form solutions generally consider the outermost phases to be infinite in extent and also assume an interfacial velocity function. It is through use of such boundary conditions that closed-form solutions are readily obtained. An extensive literature also exists on numerical solutions to the mathematically analogous solidification problem, e.g., Refs. 8 to 12. In addition, a numerical solution involving mass transfer with spherical interfaces and infinite boundaries has recently been carried out.13 A practically important class of diffusion problems exists, however, in which the boundaries of each phase away from the interface are finite. For example the finite boundary condition arises when one sets up a model for analyzing the homogenization behavior of two-component powder compacts in two-phase systems or for studying the solution behavior of precipitates. Although exact, closed-form solutions have as yet not been found to this class of problems, solutions are possible using numerical methods. The purpose of this paper is twofold: 1) to describe a numerical method for treating the two-phase, diffusion-controlled, moving-interface problem involving finite boundaries with planar, cylindrical, and spherical interfaces; 2) to present the results of a parametric study which identifies the role played by each variable appearing in the analytical model. R. A. TANZlLLI,Student MemberAIME,onleaveofabsence from the General Electric Co., Re-entry Systems Department and A. W. HECKEL, Member AIME, are Graduate Student in Materials Engineering, and Professor, Department of Metallurgical Engineering, respectively, Drexel Institute of Technology, Philadelphia, Pa. Manuscript submitted May 6. 1968. IMD MATHEMATICAL MODEL The three geometries analyzed are shown in Fig. 1. For each configuration a symmetry element is shown, across whose boundaries the mass transfer is zero. Mean composition, C, and the characteristic solute-rich phase half-thickness (or radius), 1/2, are the independent variables while the characteristic symmetry element half-thickness, L/2 (measured from solute-rich phase center to the matrix phase plane of zero mass transfer), is a dependent variable. The symmetry element for a planar interface accurately represents a real diffusion situation involving the stacking of symmetry elements of constant size. Because cylindrical and spherical symmetry elements of constant size cannot be stacked to fill space, the meaning of the dimension, L/2, for these situations may be considered in terms of the following approximations: and where NA is the number of parallel cylindrical elements per unit area on a surface normal to the cylinder axes and Nv is the number of spherical elements per unit volume. The model consists of a solute-rich phase matrix phase composite of limited mutual solubility. The concentrations at the interface are assumed constant with time; no assumption of local equilibrium at the interface is necessary except for the case where the

Jan 1, 1969

By J. Spreadborough, D. LaW. King, E. Anderson

Tmzsile tests were performed on Armco iron samples, at various ternpe.ralures and strain rates, ocer a wide range of grain sizes. Analysis of the data suggests that the plot of the lower yield stress, against d-1/2,where 2d is the acerage grain diameter, is not linear (as is often assumed) but is concave toward the d. axis over the range of d-from 7 to 53 . The different values of the parameters obtained by other workers can be explained, in part at least, by the observed curvature. This curvalure is shown to be consistent with a model of yielding based on dislocation pile-ups; however, the values of obtained by fitting our data to this model differ appreciably from the values generally reported. The equation proposed by Cottrell, viz.: is a plausible empirical fit to the experimental results. The purpose of this paper is to comment on the validity of the widely used linear relationship first proposed by all' and Petch and coworkers2"4 between ay, the lower yield stress, and 2d, the average grain diameter, for bcc metals, viz.: Many workers, see Refs. 2 to 7 and Table 11, have fitted this equation to their experimental results and have obtained acceptable fits over the relatively narrow range of grain sizes used by most of them. Indeed, in some cases, so few data points were available that any more sophisticated fit would have been irrational. In most of the interpretations,'-' oi is thought to be a measure of the friction stress accompanying dislocation movement, and ky was originally inter- preted as a measure of the dislocation locking but is now believed by Cottrell" to be a function of the dislocation creation rate. In the "unpinning" theories, k, is equated to where od is the unpinning stress and 1 is the average distance from the boundary of the grain where yielding is taking place to the nearest dislocation source in an unyielded grain. Other considerations (see, for example, Refs. 11 and 12) lead to equations with a similar form to [I] where different meanings may be attributed to the parameters. While there are doubts as to the physical significance of the parameters i and k, they continue to be used by many workers; interpretations of the variations in the behavior of ferrite materials following certain treatments, e.g., aging,'3 neutron irradiation,14 have been given frequently in terms of these parameters. Some theories of the mechanical behavior of bcc metals are based on this relationship. We have investigated experimentally the oy - d-'lZ relationship for Armco iron over a wider range of grain sizes and with more data points than those given in published results. The analysis of our data suggests that the oy—d-'" relationship is not linear but is in fact concave towards the d-'I2 axis. RESULTS AND DISCUSSION The experimental work was carried out on 3-mm-diam Armco iron rods which were prepared by wire drawing from 5-mm-diam rods. By annealing in vacuum at temperatures between 7000 and 1200°C for various times, grain sizes from 7 to 20,000 grains per sq mm were obtained, the grains in all cases being regularly shaped. Grain sizes were measured by lineal interceptand by area methods; only specimens with Amax/A values of 3 to 6 were used in the Petch-Hall plots (where A is the average area of a grain and Amax is the area of the largest grain observed). For all the specimens used, the number of grains in a cross section exceeded 50, which should be adequate to avoid grain size effects.'= Tensile tests were performed at 296", 219, and 17l°K, using

Jan 1, 1969

By H. F. Webster, C. G. Dunn

Rolling md annealing procedures are described for developing the (110) preferred orientation in tantalum for use as a thermionic-emission materinl where electrodes of a uniform high work function are needed. The development of a (110) [001] annealing texture is also reported. A preferential growth process due to low (110) gas-metal surface energy is considered in explanation of the observed growth of (110) grains. ThE growth of (110)-oriented grains in thin strips of rolled zone-refined tantalum, previously discussed briefly,' is reported together with more recent information on the formation of a (110)[001.] annealing texture, i.e., one where the [001] direction of each grain lies close to the rolling direction. The development of tantalum sheet with a (110) preferred orientation (position of [001 ] directions unspecified) is of importance as a thermionic-emission material in thermionic-energy converters. Since therm ionic-emission properties of cesium-coated crystals vary over a wide range depending on (hkl) a2-7 a single (hkl) preferred orientation is more useful than either several preferred orientations or none. Furthermore, the (110) preferred orientation yields the highest thermionic-emission density for a cesium coverage of less than a monolayer.5-7 A consideration of the stability of the grain structure needed at high operating temperatures suggests that the preferred orientation itself should be produced by annealing processes. Information on annealing textures in tantalum, however, is rather limited. Pugh and Hibbard 8 obtained (111)[112] and (lll)[112] components in a 1400°C recrystallization texture in 95 pct cold-rolled foil; these components were enhanced on annealing at 2500°C. Muller9 rolled 99.97 Ta to 90 pct reduction in thickness in the final stage and noted only a slight sharpening of the rolling texture, with some intensification of the (111)[112] component upon annealing at 1200°C. The experimental procedure followed in the present work stemmed from the idea of using possible differences in (hkl) surface energies to provide a small driving force for growth of grains having the lowest (hkl) surface energy.l0* This would mean using high-purity tantalum processed into thin sheet form and annealed at high temperatures either in a noncontaminating atmosphere or in one producing additional sample purification. EXPERIMENTAL Zone-Refined Tantalum. National Research Corp. tantalum in the form of 1/8-in.-diam rod and of 99.98 purity (53 ppm 0, 15 ppm N, and 8 ppm C) was zone-melted four times. The traversing speed was 4 mm per min. Such treatment increased the resistance ratio, R293k/R20K , where R293K is the resistance of the specimen at 20°C and R20K the re-resistance at liquid-hydrogen temperature, from a value of 25 for the initial rod to 175 for the zone-refined rod (the increase in the resistance ratio provides a measure of purification11,12). Part of a zone-refined rod was rolled unidirec-tionally to a strip 0.003 in. thick and 0.28 in. wide. Samples were given anneals in the range 1300" to 2100°C using ac conduction heating in an oil-free vacuum system. Recrystallization to small grains appeared to be complete at 1300°C. Large grains were formed at higher temperatures, but these were not entirely strain-free, some grains showing asterism in Laue X-ray patterns and some displaying a range in orientation. Part of the difficulty was caused by thermal expansion of the tantalum strip as it was held between fixed supports. However, in a different arrangement with the tantalum freely suspended in a tantalum can, high-frequency induction heating in vacuo at about l0-6 Torr produced

Jan 1, 1964

By H. D. Outmans

Present first-order theory for frontal stability and viscous fingering of immiscible liquids is improved by including the nonlinear terms in the equations describing conditions at the interface of the liquids. This leads to the revision of several conclusions which were based on first-order theory. They concern the growth rate and changing shape of a sinusoidal disturbance, particularly in relation to the wave number of this disturbance. Nonlinear aspects of effective interfacial tension are discussed and it is shown that this tension is not simply a positive proportionality constant in a linear relation between pressure difference and curvature at the interface. Scaling requirements are determined from the dimensionless groups which govern fingering. Gravity and interfacial tension invalidate a previously formulated conclusion that the shape of a finger after a given displacement is independent of the displacement velocity. Also, similarity of fingering (and, hence, of sweep efficiency in case of an unstable front) requires geometrical similarity of the initial disturbance in the model and the reservoir with a scale factor which is the same as the one for scaling down the dimensions of the reservoir. INTRODUCTION The critical velocity at which the transition zone in the vertical displacement of immiscible liquids becomes unstable was calculated by ill. More recently, the same was done for nonvertical displacements and it was also shown that the stability is affected by an effective interfacial tension between the liquids. 2-4 Although in the oil reservoir a stable front is always desirable from a recovery point of view, the necessary velocity may have to be so low that the corresponding production rate is not economical. In that case, a knowledge of the fingering unstable front is necessary for predicting recovery at break- through. Studies in this direction have not gone beyond the very moment at which fingering first occurs.5,6 Conclusions about stability and fingering in these references are all based on linear theory. In this theory the nonlinear terms in the equations describing conditions at the front are neglected. The usual justification for this lack of mathematical rigor is that the nonlinear terms can be made small relative to the linear terms and, supposedly, small causes produce only small effects. It has been recognized, however, that this is not necessarily true in the nonlinear problems of hydrodynamics.7 The hydro-dynamic stability and fingering of the front between two liquids, accelerated in a direction normal to the front, for instance, is strongly influenced by the nonlinearity of the boundary conditions.8-10 Since these boundary conditions are not unlike those arising in the problem of stability and fingering of the front during a slow immiscible displacement in porous media, it was thought that there, too, the nonlinear terms should be taken into consideration. A summary of the results obtained in linear theory and a comparison with experimental data precede the nonlinear theory developed in this paper. This summary serves to introduce some quantities which will be used in the further develop ment. It should also be pointed out that the method of higher-order approximation by which the nonlinear stability problem is solved has application in other reservoir studies.11 SUMMARY OF LINEAR THEORY 1. A plane interface remains stable if its velocity is smaller than a critical velocity. vc = (p2-p1)gn/(l/A2- l/A1 .........(1.1) This equation is derived for uniform flow in a thin layer inclined to the horizontal plane. The displacement takes place in a direction normal to the intersection of this layer and the horizontal plane. The undisturbed (line) interface is normal to the velocity. Fluid 1, the upper fluid (gas), is displacing Fluid 2 (oil). (VcQS would be the injection rate in cc/

By M. J. Hordon

Measurements of the 103 yield stress of ordered and disordered poly crystalline Cu ,Au were related to the ordered antiphase domain size determined by resistivity measurements. For undeformed material, a yield stress maximum wa obtained at a critical domain diameter of about 40A. Plastic deformation resulted in a marked increase in the yield stress and electrical resistivity of the ordered alloy compared to the disordered, the strain hardening rate increasing regularly with initial antiphase domain size. Order hardening was accompanied by a sharp reduction in size of the initially large domains. It has been observed that the yield stress of ordered and partially ordered Cu3Au alloy varies sensitively with antiphase domain size aid degree of order.ly2 In addition, ordering of the lattice leads to a marked increase in the strain hardening rate (order hardening) as compared to the rate for the disordered alloy. In the present investigation, changes in the electrical resistivity and yield stress of ordered polycrystalline Cudu with varying initial domain diameters were measured after tensile plastic deformation in order to examine the effect of cold work on the antiphase domain size. EXPERIMENTAL PROCEDURE Au-Cu alloy of 99.99 pct purity analyzing 50.85 wt pct Au-balance copper was obtained from the Handy-Harmon Co., N. Y., in the form of 0.061 in. diam drawn wire. Wire specimens 3 in. in length were given the following annealing treatment in nitrogen: 500" for 72 hr, 820" for 15 hr, and 450" for 5 hr, followed by a water quench. The annealing sequence resulted in a completely disordered structure with a grain size of about 0.2 mm. The disordered specimens were then reannealed at 360' in nitrogen for periods varying from 10 min to 150 hr followed by quenching to produce ordered structures with varying domain sizes. The degree of ordering and variation of domain size was followed by electrical resistivity measurements made at room temperature using a low resistance precision Kelvin double bridge apparatus. The specimen resistance was determined over a length of 4.0 cm between two brass knife-edge contacts while the specimen was immersed in an oil bath to minimize temperature variations. In addition, the current flow in the circuit was minimized by a current pulse technique in balancing the bridge in order to avoid heating the specimen. Using a sensitive galvanometer to detect the bridge null, the accuracy of the resistance measurement Wire specimens were plastically strained in tension with an Instron tensile unit at strain rates in the range 5 x 10"5 sec-' to 2 x 10"4 sec-'. Stress and extension data were fed into the Instron chart drive amplifier to obtain the actual stress-elongation curve from which the yield stress at 10"3 strain was determined. The maximum resolution of the apparatus was approximately 50 psi stress and 3 x 104 strain. At various plastic strain levels, deformation was interrupted and the electrical resistivity determined after removing the stress. RESULTS AND DISCUSSION 1) Yield Strength of Ordered Cudu. In order to determine the effect of the ordered antiphase domains on the initial yield stress, specimens were prepared with varying domain sizes ranging from zero for 5 completely disordered structure to about lo5A for a completely ordered structure by suitable annealing treatment. Domain sizes were estimated by comparing room temperature electrical resistivity data with the original data of Jones and sykes3 as modified by rdle.' In agreement with previous work, the resistivity varied sensitively with domain diameter and degree of order, decreasing from approximately 11.6 x l0- ohm-cm for the disordered structure to about 5.9 x l0- ohm-cm for ordered domains above 10"3 cm in diameter. Fig. 1 shows the change of the 103 yield stress with ordered domain size. It is evident that the maximum

Jan 1, 1963

THE John Fritz Medal Board of Award, at its regu¬lar annual meeting Oct. 19, awarded its gold medal to Herbert Clark Hoover. Thus ended a process of selection begun a few years ago. The award was tentatively made a year ago by the Board, which is composed of sixteen recent past-presidents of the four national societies of Civil, Mining and Metallurgical, Mechanical, and Electrical Engineers, having together a membership of nearly 60,000. The sixteen members of the Board are: American Society of Civil Engineers : C. E. Grunsky, Robert Ridgway, George S. Davison and John F. Stevens ; American Institute of Mining and Metallurgical Engineers: William Kelly, J. V. W. Reynders, Samuel A. Taylor and E. DeGolyer; American Society of Mechanical Engineers: Fred R. Low, D. S. Jacobus, Dexter S. Kimball and Charles M. Schwab; American Institute of Electrical Engineers: Farley Osgood, M. I. Pupin, C. C. Chesney and Bancroft Gherardi.

Jan 1, 1928

By R. J. Stoehr, F. Howell

Since the ore mined in the Grants-Ambrosia Lake uranium area is taken from a water-saturated sandstone formation, part of the milling operation includes a drying process. The authors discuss the merits and disadvantages of two methods: natural drying and mechanical gas-fired drying; operating and cost data are included. In the Grants-Ambrosia Lake uranium area, approximately 7000 tons of ore are mined each day from a water-saturated sandstone formation. This ore is sampled and treated at four separate milling operations. Prior to the design and initial construction of the milling facilities, very little was known as to the physical properties of the ore which would be handled in the sampling and crushing facilities at the mills. All four mills initially were constructed without ore-drying facilities. As mining proceeded, it was determined that, even after drying the ore in place by use of drainage development underground, the moisture content of the ore as hoisted averaged approximately 18 pct. Actually, some of the mines produced ores which resembled cream-of-wheat in character and had a moisture content in excess of 24 pct. Each of the four mills had a differently designed sampling and crushing plant; therefore, the moisture content of the ores had varying adverse effects upon the operation of the plants. It was determined after some experience that most of the sampling and crushing facilities could not economically handle ore if the moisture content was greater than 10 pct—one operator considers 12 pct moisture as a maximum. In all of the plants, moisture content over 8 pct increases costs to some extent. In addition to the added sampling and crushing costs, some of the mills were located 15 to 20 miles from the mines and the high moisture content of the ores increased the haulage costs from the mine to the mill. It was generally conceded that it was necessary to employ some method to reduce the moisture content of the ore prior to sampling. Several methods were considered: 1) natural drying at the mine site, 2) mechanical gas-fired drying at the mill site, 3) mechanical gas-fired drying at the mine site, 4) radiant heating on concrete clabs, and 5) infrared shed drying. After preliminary investigation all possibilities but natural drying and mechanical gas-fired drying at the mill site were eliminated. NATURAL DRYING A cooperative feasibility study was conducted on the natural drying method. This study indicated the following: 1) During summer months May through September, ore piled 4-ft deep would dry from +20 to +10 pct HzO in 30 days with no mechanical turning. 2) In the first four days after piling a reduction of 5 to 7 pct total moisture content was accomplished by drainage and absorption of the water into the underlying ground on which the ore was piled, providing the ground surface absorption rates approached 10 gal per sq ft per day. After the first four days the decrease of moisture caused by drainage was practically nonexistent. 3) In the summer months drying by evaporation amounted to approximately 0.1 pct decrease in total moisture per day and mechanical turning of the ore could increase this as much as three times. 4) Climatic conditions of the area indicated that: a) Air temperatures averaged 64' May, June, July, August, September; 41" October, November, December, March, April; 31" January, February. b) Average rain fall was 10 in. with 40 pct of this occurring during July and August. c) Only on very rare occasions were there over five consecutive days with below freezing temperatures. d) The annual evaporation rate was approximately 75 in. On the basis of this study, two of the mill operations decided to attempt to meet the moisture specifications by natural drying supplemented by mechanical turning. The other two operations decided upon rotary gas-fired drying at the mill site. The natural drying method has been quite successful in practice. The ore running approximately 18 pct moisture is trucked from the head frame and piled in rows about 6 ft wide, 3 1/2 ft deep, 5 feet apart during the months of May through September. In approximately 30 days this ore will

Jan 1, 1961

ALABAMA Altoona -Cain, J Anniston -Cowie, L K Heimrod, A A White, H E Bessemer-Abbott, C C Ball, E M Mitchell, F R Thompson, N E Birmingham -Adler, T E Aldrich T H Aldrich, T H, Jr Blackburn, A R Bush, 117 W Clark, G H Cowin, P G Crane, W R Crawford, G G Crockard, F H Darnelspn, G E Davis, C B

Jan 1, 1923

By Lynn C. Jacobsen

Among the unforeseen consequences of the 1973 Arab oil embargo has been a considerable array of new or increased taxes on the so-called energy minerals. These taxes will be the subject of this report. Both Federal and State taxes have been enacted, but I will be concerned mostly with state severance taxes and particularly those on uranium. Severance taxes are considered to include all taxes having the distinctive feature of being applied on a natural resource at the stage of extraction. The tax may be based on units of production or on value, and if on values it may be on gross value or on gross value less either arbitrary or cost-related deductions. The tax has a number of aliases - resource excise tax, conservation tax, privilege tax, mining excise tax, ad valorem production tax, and more - and this makes comparison of tax burdens among states difficult. The windfall profit tax on oil is an example of a severance tax at the Federal level. Severance taxes are an established feature of state tax systems, but they continue to be a controversial issue, and proposals to raise or modify existing severance taxes are regularly submitted to the legislatures of the Western energy producing states. No concensus exists as to what is a reason- able and proper level of severance taxation or to the form it should take. The taxes which have been adopted by the various states reflect the interaction of a variety of interests and the specific circum- stances in each state. What follows is a summary of theoretical, practical, and emotional viewpoints and arguments that surface in any statehouse in which a severance tax bill has been introduced. The New Mexico experience will be heavily relied upon. THE ECONOMISTS Marginal effects. A severance tax which is based on a gross percentage of revenue or on units of production is a constant addition to variable costs, and to the mine operator has the same effect as any other increase in operating costs. The direction of these effects is straightforward: the tax will cause the property to have a lowered present value, to be mined at a lower rate than without the tax, raise the minimum grade that will be mined, lead to lower total recovery, make marginal properties sub-marginal and discriminate in favor of richer, more profitable operations (Lockner, 1965; Steele, 1967). In the short run, production facilities are fixed and imposition of a severance tax will have little effect on production levels. In the longer term, capital is mobile and investment and exploration expenditures will shift from minerals and jurisdictions with high taxes to those with low taxes. Over a considerable range of taxation the effect will be to change the relative position of the taxing state, but an overly optimistic evaluation of the capacity of mineral producers to absorb a tax can bring an industry to a halt. It is generally acknowledged that imposition of high severance taxes on taconite in Minnesota stopped development completely, and that only the adoption of a constitutional amendment limiting the amount of taxes that could be imposed in the future brought the firms back and encouraged them to make the huge investments required (Weaton, 1969). A tax which is a percentage of the net operating income (gross revenue less cash operating costs) does not influence the cut-off grade for recovery nor change the time preference for extraction, and hence, is free of the negative features of the tax applied to gross revenues or units of production. In theory it is a more efficient tax but relative administrative complexity and inherent difficulty in predicting revenue have discouraged its use. The Wyoming severance tax on uranium, which uses grade of ore as well as price in establishing taxable value, is the most cost related, and hence, the most neutral and efficient of the various state severance taxes on uranium. Economic rent. Despite the discrimination and the anti-conservation aspect inherent in most severance taxes, economists generally endorse their use because they are seen as a vehicle to appropriate rents - that is, returns greater than the long-run competitive supply price. Conspicuous examples of supposed economic rents are the returns to oil producers because of the OPEC cartel, the returns of the uranium producers under AEC buying contracts in the 19501s, and the high prices obtained by the uranium producers for contracts entered into in the 1976-1979 period. Mining of coal in the Western states is believed by some to generate huge economic rents because of the OPEC caused increase in price of a competitive fuel (McLure, 1978, p. 261), and possibly because of clean air regulations favoring the burning of low-sulfur coal. In theory, such surplus returns could be taxed completely away without affecting supply. In practice, the situation is more complex (Steele, 1967, pp. 234-236); economic rent of mineral production is an elusive quantity involving as it does replacement costs, and technical and market risk, and it, like beauty or pornography, probably exists mostly in the eye of the beholder. Rent may also be perceived to be present in the upper portion of a cyclic market which also has a downside. Where rent exists, it is almost certain to be short-lived - cartels self- destruct, government subsidies end, competitive adjustments occur - but the taxes imposed to capture it tend to be immortal. There is little doubt that the perception of un- usual and undeserved (obscene) profits in the mid- and late 1970's was a major factor in the adoption of energy mineral taxes strikingly higher than had been previously considered. At the New Mexico legislature of 1977 supporters of a moderate tax were repeatedly confronted with some variant of the statement, "You can't expect me to believe that a

Jan 1, 1982

By Robert Laurich

Chuquicamata pit was opened in 1915 with steam shovels and steam locomotives brought down from the Panama Canal excavation project. With expansions in the early years, more steam locomo¬tives were brought into the mine. IMPROVED LOCOMOTIVES During the period 1927 to 1937, electric locomo¬tives were purchased and main line and bench tracks were electrified. Third rail was installed up to the working areas. At first, the locomotives were equipped with batteries for service at the shovels, but charge life was too short and they were con¬verted to use the third rail and a reel with 3000 ft of trailing cable for service in the loading area.

Jan 11, 1959

Discussion of the paper of CLARENCE A. WRIGHT, presented at the St. Louis meeting, October, 1917, and printed in Bulletin No. 130, October, 1917, pp. 1565 to 1591. H. A. WHEELER, St. Louis, Mo.-This paper by Mr. Wright is one of the most thorough and exhaustive studies that has been made of the milling practice in the Joplin district. Mr. Wright spent about two years there, in behalf of the U. S. Bureau of Mines and the Missouri Geological Survey, and this paper, which is the result of his work, will, repay careful reading by any student of ore dressing and is invaluable to an operator in that district.

Jan 1, 1918

DISCUSSION, M. Cohen presiding A. H. Geisler and D. L. Martin (GeneTal Electric Research Laboratory, Schenectady, N. Y.)—We were rather interested to note the author's conclusion that the cubic to tetragonal transformation may be of the second order, for we have been able to show that the order-disorder transformation in an analogous alloy system is a first-order transformation with a discon-

Jan 1, 1952

By H. D. Kynor

By the term mechanical mining is meant that operation, or series of operations, that replace the hand methods of mining. The first undercutting machine to operate in anthracite was placed in the Butler mine of the Hillside Coal and Iron Co., Dec. 23, 1910, by the Sullivan Machinery Co. The first Jackhamer used in the anthracite field was installed at the Wadesville colliery of the Philadelphia & Reading Coal and Iron Co. in Oct., 1912, by the Ingersoll-Rand Co. The first longwall conveyor was installed at the Dodge mines of the Delaware, Lackawanna, & Western Coal Co. in March, 1912. The first mechanical scraper equipment was installed in the Seneca mines of the Lehigh Valley Coal Co. in January, 1914. The amount of anthracite mechanically mined since the first mining machine was installed in 1910" is as follows: Penna. Coal Co. D. L. & W.. ScRanton Temple Hudson YeaR and Hill- Tons Coal Co., Coal Co., Coal Co., Total, side Coal Tons Tons Tons Tons and Iron. Tons 1920................ 372,737b 367,000d 322,892 74,127 371,878 1,508,634 1919................ 950,786 no record 306,616 81,575 319,356 1,658,333 1918................ 917,778 744,966 24,880 44,756 288,781 2,021,161 1917................ 757,940 838,800 5,050 57,279 164,180 1,823,249 1916................ 286,780 860,663 13,960 114,173 101,475 1,377,051 1915................ 428,819 592,169 8,253 1,029,241 1914................ 219,188 153,896 373,084 1913................ 171,505 1912................ 124,267 124,267 1911................ 40,319 40,319 1910................ 1,184 1,184 a A slightly greater production was obtained than here indicated, as the tonnage from individual operations is not shown. b Decrease due to strike conditions in 1920. c Does not include tonnage of D., L., & W. d D., L., & W. decrease in 1920 due to having fewer mining machines in operation. There are about 150 undercutters in use in the anthracite region, 80 mechanical loaders, and 10 longwall conveyors.

Jan 1, 1922

MONTANA SECTION W. C. SIDERFIN, Chairman, OSCAR ROHN, Vice-Chairman, E. B. YOUNG, Secretary-Treasurer, 526, Hennesey Building, Butte, Mont. F. W. BACORN, C. D. DEMOND. The semi-annual meeting of the Montana Section was held at the Silver Bow Club, Butte, Montana, on Friday, Nov. 16, at 8 p. m.; this was a postponement of the regular October meeting because of conflict in date with the St. Louis meeting of the Institute. An informal dinner was served to 68 members and guests. After dinner, Chairman W. C. Siderfin called the meeting to order. The minutes of the annual meeting, of Feb. 2, 1917, and the special meeting of May 21, 1917, were read and approved. C. W. Goodale led the discussion with "Notes on the St. Louis Meeting." He was followed by J. H. Warner who spoke on " The Joplin and Miami Districts," and by J. L: Bruce, Alexander Leggatt, N. B. Braly, and E. B. Young, the latter speaking on the work of the War Minerals Committee; and on the Cosden Oil Refinery at West Tuba, Okla. R. H. Sales reviewed briefly the manganese situation. E. N. Norris presented a paper on "Fire Proofing of Mine Shafts by the Anaconda Copper Mining Co." This resulted in interesting discussion by C. L. Berrien, C. E. Nighman, N. B. Braly, W. B. Daly, B. H. Dunshee, and J. J. Carrigan. C. L. Berrien and C. E. Nighman presented their papers on "Fire Extinction by Hydraulic Filling." In view of the late hour, discussion was waived. The executive committee, by unanimous consent, decided to request written discussion of the above papers to be presented at the next meeting, in February. B. B. Thayer spoke interestingly on the work of the Naval Consulting Board, and referred to the arsenic situation. Spencer Miller, also a, member of the Naval Consulting Board, entertained the-meeting with a vivid description of the method of "Coaling Battleships at Sea." Robert Sticht of Tasmania, in a short talk, spoke feelingly of his relations with the United States. At a late hour adjournment ended a most successful and interesting meeting. E. B. YOUNG, Secretary.

Jan 1, 1918