Search Documents

By H. E. Strauss

The time-to-fracture test has been applied to pure platinum and to two alloys of platinum under the special conditions of small cross-sectional area of the specimens and of a test temperature above the annealing temperature. While the results are similar in character to those secured with large specimens of steel at temperatures below the annealing temperatures, two differences are noted: (I) an upward inflection in the curves for log stress vs. log time for the alloys, and (2) a sharp break in the curve for log stress vs. log time for pure platinum when single crystals filled the wire. The experiments showed that: (I) platinum and 10 per cent rhodium-platinum maintained their strengths at IIOO°C. better than did to per cent iridium-platinum, and (2) the rhodium-platinum after a time exceeded the iridium-platinum in strength at IIOO°C. Platinum alloys in their service at high temperatures encounter conditions somewhat similar to those that exist in the usual form of the "time-to-fracture"l test with steel. This paper is intended primarily to present results obtained by a "time-to-fracture" test under conditions approximating actual service for platinum (at the temperature IIOO°C. under oxidizing conditions) with three materials, pure platinum (99.99 per cent), a platinum alloy with 10 per cent iridium, and a platinum alloy with 10 per cent rhodium. The experimental procedure differed from that previously used in this type of measurement in that the samples were of small diameter (0.010 in.), were fully annealed, and were tested at a temperature definitely above their annealing points (600°C., IOOO°C. and 1050°C., respectively, for 60 per cent cold reduction and 15 min. heating time2,3). The experimental arrangement was similar to that previously described,' using as heating unit a small, horizontal, platinum-wound furnace, ½ by 12 in., maintained at constant temperature by an automatic controller. The samples were 0.010-in. wires, which had been annealed at 1200°C. by drawing them slowly through the furnace. The time-to-fracture was measured electrically. Elongation was not determined because of the difficulties inherent in the experimental arrangement. Life—that is, the time-to-fracture—was considered the important property in these first tests. No attempt was made to measure the reduction in area, but the types of fracture were noted qualitatively; in the text they are referred to as (I) the normal, plastic, or necked fracture, (2) the knife-edge fracture, and (3) the brittle or intercrystalline fratture with small reduction of area. Results for different constant applied stresses are plotted in Fig. I. In all cases at least two trials were made for each stress, although they cannot always be indicated separately on the curves. The breaking Stresses drop very rapidly to a small frat-286

Jan 1, 1943

By H. E. Strauss

The time-to-fracture test has been applied to pure platinum and to two alloys of platinum under the special conditions of small cross-sectional area of the specimens and of a test temperature above the annealing temperature. While the results are similar in character to those secured with large specimens of steel at temperatures below the annealing temperatures, two differences are noted: (I) an upward inflection in the curves for log stress vs. log time for the alloys, and (2) a sharp break in the curve for log stress vs. log time for pure platinum when single crystals filled the wire. The experiments showed that: (I) platinum and 10 per cent rhodium-platinum maintained their strengths at IIOO°C. better than did to per cent iridium-platinum, and (2) the rhodium-platinum after a time exceeded the iridium-platinum in strength at IIOO°C. Platinum alloys in their service at high temperatures encounter conditions somewhat similar to those that exist in the usual form of the "time-to-fracture"l test with steel. This paper is intended primarily to present results obtained by a "time-to-fracture" test under conditions approximating actual service for platinum (at the temperature IIOO°C. under oxidizing conditions) with three materials, pure platinum (99.99 per cent), a platinum alloy with 10 per cent iridium, and a platinum alloy with 10 per cent rhodium. The experimental procedure differed from that previously used in this type of measurement in that the samples were of small diameter (0.010 in.), were fully annealed, and were tested at a temperature definitely above their annealing points (600°C., IOOO°C. and 1050°C., respectively, for 60 per cent cold reduction and 15 min. heating time2,3). The experimental arrangement was similar to that previously described,' using as heating unit a small, horizontal, platinum-wound furnace, ½ by 12 in., maintained at constant temperature by an automatic controller. The samples were 0.010-in. wires, which had been annealed at 1200°C. by drawing them slowly through the furnace. The time-to-fracture was measured electrically. Elongation was not determined because of the difficulties inherent in the experimental arrangement. Life—that is, the time-to-fracture—was considered the important property in these first tests. No attempt was made to measure the reduction in area, but the types of fracture were noted qualitatively; in the text they are referred to as (I) the normal, plastic, or necked fracture, (2) the knife-edge fracture, and (3) the brittle or intercrystalline fratture with small reduction of area. Results for different constant applied stresses are plotted in Fig. I. In all cases at least two trials were made for each stress, although they cannot always be indicated separately on the curves. The breaking Stresses drop very rapidly to a small frat-286

Jan 1, 1943

By D. W. Brunton

Discussion of the paper of D. W. Brunton, presented at the Spokane meeting, September, 1909, and published in Bulletin No. 33, September, 1909, pp. 837 to 855. WILLIAM' KENT, New York, N. Y.:-The Institute may congratulate itself on the opportunity of reading the splendid address of President Brunton. It is au admirable summary of the progress that has been made in the mining and metallurgical arts in recent years. The paper rightly give's the chief credit for this progress to the aid which has been rendered to these arts by the advances in mechanics, chemistry, and electricity. It is notable that most of the headings in Mr. Brunton's address refer to the work of the mechanical engineer, the electrical engineer, and the chemist, rather than to that of the specialist in mining-operations. It seems that. the most successful mining engineer of the present day is the one who makes the most intelligent application of the inventions and designs of engineers and others who are not directly engaged in mining. A tabulation' of the headings of the address, grouped as below, shows this most clearly. Work of the Mechanical Engineer-Rock-drills, hoisting-machinery, tramming, pumping, ventilation, dredging, sampling, concentration, briquetting, fume-recovery. Work of the Electrical Engineer-Electric machinery for hoisting, pumping, tramming, lighting and signaling, electric . transmission, electric smelting. Work of the Chemist and Metallurgist-Explosives, chlorination, cyanidation, roasting, lead-smelting, and copper-smelting. Work of the Geologist-Economic geology. Work of the Mining Engineer-Mine-mapping, surface-mining, timbering, tunneling; and planning and supervision of the work in general. The mining engineer of the present day, who is in responsible charge of a large plant, finds his chief work not in doing

Jan 1, 1910

By L. F. Stutzman, George Thodos

A new graphical method, which is a modification of that proposed by Buckley and Leverett', is presented for the determination of the displacing fluid saturation at breakthrough for frontal drive mechanisms. This method is applicable to all types of fluids, which may be either soluble or insoluble in the oil at reservoir and injection conditions. This adaptation has unique advantages in handling problems in which either liquids or gases are the displacing fluids. INTRODUCTION In the displacement of oil from a reservoir with water or gas injected into the formation or by the expansion of a gas cap, the determination of breakthrough or flood advance is important to define the initial and subordinate phases of the operation. Thus, the determination of the displacing fluid saturation at breakthrough is fundamental to the establishment of over-all reservoir production. Methods for analyzing this saturation and for calculating production rates have been previously reported1,'*".". All of these methods utilize the rate equation for linear flow developed by Buckley and Leverett1. xs = QT - Qn/A? (?fu/?Su) .....(1) Sp where f, represents the volumetric fraction of displacing fluid in the total flowing fluid within the reservoir as is defined by: fo = 1/1+ ku/kd µn/µn .......(2) Since the time, ?, necessary for the flood front to travel distance ?X is unknown, Eq. 1 cannot be solved directly for the determination of the breakthrough point. Therefore, it becomes necessary to solve Eq. 1 simultaneously with an equation representing a fluid bal-ance on the reservoir behind the flood front. To develop such a fluid balance equation, it has been assumed that the fluid composition is uniform in the reservoir behind the flood front. Based upon this assumption, the follow-ing equation can be derived from a material balance on the displacing fluid: x = (?X) s Dx ? x=0 [ Snx - Sn1 ] dx = QT - Qn/A? It is readily observed that the displacing fluid satura-tion behind the flood front, Snx, may be determined through the simultaneous application of Eqs. 1 and 3. Although the approach may vary, this objective re-mains the same for all of the previously mentioned graphical or analytical methods. After Sox is determined, it is then possible to calculate the gas-oil and/or water-oil ratios and the rates during the initial and subordinate phases of production, and thereby define the production history of the reservoir. In this presentation only the de-termination of Snx is considered, and the reader is re-ferred to the several texts in reservoir engineering2,4,5 for a complete discussion on the methods for establish-ing the production history of a reservoir. PROPOSED METHOD FOR DETERMINING Snx Since at any time the quantity, QT - Qn/A? is a constant, Eq. 1 may be expressed in differential form as follows: dxsn = QT - Qn/A? d (? fn/? Sn) sn .....(4) Eq. 4 may be substituted directly into Eq. 3 to obtain: ? fn/? Sn ? [ Snz - Sn] QT - Qn/A? d ( ? fn/? Sn) = QT - Qn/A? ...............(5) Eq. 5 simplifies to the expression: ? fn/? Sn ? [ Snz - Sn] QT - Qn/A? d ( ? fn/? Sn) = 1 ....(6)

Jan 1, 1958

By Walter O. Snelling

Discussion of the paper of WALTER 0. SNELLING, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 100, April, 1915, pp. 695 to 704. A. C. McLAUGHLIN, San Francisco, Cal.-It seems to me that Mr. Snelling's work, if it is what it appears to be, is one of the most important contributions to petroleum technology that has been brought out iii the last 25 years. If his end products are what they seem to be, he has made a discovery, which, in my judgment, will revolutionize the petroleum industry. As to industrially carrying out these processes I do not think there is the slightest difficulty, for I have had some work recently where crude oils were handled successfully at a temperature of 750°F. and pressure of 750 lb. per square inch. WILLIAM A. WILLIAMS, San Francisco, Cal.-What metal did you use, Mr. McLaughlin? - A. C. McLAUGHLIN.-Ordinary seamless tubing, extra strong. WILLIAM A. WILLIAMS.-Tests were made in Dr. Rittman's experimental plant at Pittsburgh, upon samples of residuum furnished by Mr. Bell, the residuum being the remainder of the crude oil after the lighter fractions had been removed. After the material had been run through Dr. Rittman's plant, yields of from 43 to 58 per cent. of material, boiling under 150°C. were obtained. The distillate had a peculiar odor, due to the presence of benzene, toluene, and other unsaturated hydrocarbons. W. N. BEST, New York, N. Y.-What is the difference between the Rittman and the Snelling process or system? WILLIAM A. WILLIAMs.-The fundamental difference is that reactions take place under relatively higher temperatures and pressures and with none of the oil present in its original or liquid state, while the reactions secured by Mr. Snelling and other investigators have been from the liquids in the presence of some vapors. Under such conditions as Mr. Snelling operates, the temperatures and pressures used are limited and the flexibility in the control of these variables is extremely limited when compared with the Rittman process.

Jan 1, 1916

Executive SCOTT TURNER, Chairman FREDERICK M. BECKET JOHN A. MATHEWS H. A. GUESS WILLIAM WRAITH Finance HENRY KRUMB, Chairman PAUL D. MERICA ROBERT E. TALLY Admissions JOHN M. LovEJOY, Chairman GEORGE D. BARRON ERLE V. DAVELER WILLIAM H. BASSETT W. D. B. MOTTER, JR. Alternates HENRY B. FERNALD F. JULIUS Polls AMOR F. KEENE

Jan 1, 1932

Jan 1, 1968

Jan 1, 1970

By J. R. Stone, J. T. Roy

ASARC09s continuous tapper for lead blast furnace is described. Its use throughout the company's plants has resulted in higher production rates, lower labor costs, and better working conditions. It has also permitted wide latitude in blast pressures, as well as in charge and slag compositions. The practice of tapping a lead blast furnace has remained essentially unchanged for many years. In principle, it is a batch operation discharging the products from the continuous smelting of lead-bearing materials. As such, it imposes certain restrictions on the proper functioning of the smelting operation. First, it calls for a highly developed sense of timing, and a considerable amount of physical effort on the part of the operator. Dirty and hot working conditions, as well as the hazards of flying metal and slag, usually prevail. These conditions have resulted in higher labor costs, both in rate and in amount. Labor turnover has also been high. Secondly, rigid control of mechanical and metallurgical factors must be maintained. Frequent oxygen lancing of the tap hole is needed to permit tapping, thereby increasing operating costs. Rapid increases in smelting rate, plugged tap holes, or forgetfulness on the part of the operator may permit the molten material to rise above the tuyeies and freeze the furnace. Also, the operator will often blow out the tap hole after draining, filling the area with fume. Composition of charge also vitally affects the tapping. The type of lead-bearing material being smelted will naturally affect the smelting rate, and thus the frequency of tapping. The amounts and types of fluxing materials, which determine the ultimate fluidity of the slag, must be regidly controlled. Finally, the batch tapping of a continuous smelting operation of this type appears to be wrong in principle. The molten material drains into the crucible at the bottom of the furnace where it starts cooling immediately and continues to cool until tapped out. While keeping the lead molten is no particular problem, maintaining a fluid slag at all times is often difficult, and sometimes impossible. These factors all point to the desirability of a method for the continuous tapping of a lead blast furnace. The expected advantages would be more desirable working conditions, lower labor costs, increased production, and a much wider latitude in both blast pressure and charge composition. CONTINUOUS TAPPING Historical. A number of devices, e.g., mechanical tappers, siphons, and lead wells, have been tried in the past in attempting to effect continuous tapping. None proved to be entirely satisfactory for tapping lead and slag simultaneously. It was not until 1955, however, that ASARCO designed and put into operation a successful tapping unit at its East Helena, Mont. lead smelter. This unit is described in detail in U.S. Patent NO. 2,890,951. Continuous Tapping Unit—See Figs. 1 and 2. Fig. 1 is a schematic drawing of the unit in place, showing front and side views. The component parts are identified in the caption. Fig. 2 is an actual photograph, front view, of the tapping unit attached to the base of the blast furnace. Operation. The operation of the tapping unit is quite simple. Essentially it consists of a narrow tapping bay surrounding the furnace tap hole, with a deep notch in the front wall. When the blast furnace is started this notch is open down to the level of the tap hole. Starting the furnace may be accomplished in several ways but the most satisfactory method is to plug the tap hole with clay, permitting metal and slag to build up inside the furnace. Before the liquid reaches the tuyeres, the plug is removed and the furnace is drained to the settler. The blast is then stopped momentarily while the notch in the front wall of the tapping bay is dammed with chrome brick and plastic chrome ore. The blast is again started, and the height of the dam is adjusted so that the liquid in the bay will counterbalance the internal pressure of the furnace. When the desired level is reached the slag and metal will overflow to the settler. It should be noted that the molten material ,is not siphoned from the furnace and that the metal 'acts as a liquid valve controlling the flow of slag through the tap hole. During normal operations the tapping bay is filled primarily with lead, covered with a thin layer of slag. Thus, the heavier lead plays the major role in compensating for variations in furnace pressures. Due to the high specific gravity of lead, changes in the liquid level in the tapping bay will never exceed a few inches. For this reason it is seldom necessary to change the height of the dam due to minor variations in operating conditions. Some turbulence of the liquid in the bay is essential at all times. This indicates that the level of the

Jan 1, 1963

By T. Price, H. A. Holl, A. P. Greenough, A

UdIN, Shaler, and ulff' first used wires for the determination of the surface energy of a solid metal. A gage length was marked by tying knots in the wires, which were then suspended in a cylinder of the same metal, heated in an inert atmosphere for the appropriate time, cooled to room temperature, and finally removed from the furnace so that the lengths of the wires could be measured. With iron wires, difficulties associated with deformation during the phase changeszp3 made it necessary to measure the gage lengths at the tem-

Jan 1, 1964

By E. R. Darby

When bronze is melted in open-flame furnaces a considerable amount of slag is formed during the melting operation. This slag may be incidental to the melting practice or it may be formed intentionally by slag-forming constituents added to the furnace charge to provide a covering for the melted metal When this slag is removed from the furnace, it contains, in addition to the free metal carried with it by the skimming operation, a considerable amount of metal as oxide either combined or mechanically mixed with it. By the usual crushing and washing methods this metallic oxide generally goes to the tailings pile, so diluted by other foundry waste that its recovery is economically impossible. If this furnace slag is not inixed with other foundry waste, practically all of the metal oxide as well as the free metal may be recovered by some form of smelting operation. The first side of the problem to be considered is the amount of slag produced. It may not be true that the majority of foundries have no record of the amount of slag made, but it is certainly true that a very great many either have no record or pay little attention to it. Usually the collection of furnace slag for one normal week's run will be sufficient to determine the advisability of its being handled in a different manner from the crushing and concentrating generally employed. If a large representative sample of the accumulation is crushed and concentrated and the recovery compared with the results of a careful assay, it will be found that a large percentage of the total metal content was lost in the washing process. The percentage of loss will be greater than the metallic oxide content, as some free metal in extremely fine particles always is carried away in grains of slag. From such a comparison, it may be determined whether or not the slag should be melted, sold or treated as before. An example of an actual test of this kind is given below. In a foundry melting 50,000 to 80,000 Ib. of bronze per day, a week's accumulation of furnace slag and ladle skimmings amounted to 16,500 1b.—over three times as much as the foundry superintendent estimated before the accumulation was made. Two tons of this material was taken as representative of the lot. This was ground through a thoroughly cleaned ball-mill and concentrated over a Wilfley table. The

Jan 1, 1970

Jan 1, 1967

By Arthur Nomann

Recording instruments may be conveniently described under the headings of: (1) geophones, (2) amplifiers, (3) recording cameras, (4) miscellaneous parts. Geophones Geophones or seismometers are actuated by slight earth movements, and generate electrical currents, which are amplified and recorded. In all geophone desigm there is provision for differential movement between parts of the mechanism and the signal voltage is generated as a function of this differential movement. The part that conforms to the movement of the ground is called the support, and the part that remains more nearly stationary with respect to more distant unactuated parts of the earth is called the steady mass. The mechanical period of the geophone is the time required for an oscillation of the steady mass after an initial impulse is given it, and is determined by the effective stiffness of the spring joining the two parts together in relation to the weight of the suspended part. Geophones have been used with frequencies varying all the way from less than 10 cycles per sec. to several hundred cycles per second. Those with a natural frequency of less than, say, 100 cycles

Jan 1, 1940

By Arthur Nomann

Recording instruments may be conveniently described under the headings of: (1) geophones, (2) amplifiers, (3) recording cameras, (4) miscellaneous parts. Geophones Geophones or seismometers are actuated by slight earth movements, and generate electrical currents, which are amplified and recorded. In all geophone desigm there is provision for differential movement between parts of the mechanism and the signal voltage is generated as a function of this differential movement. The part that conforms to the movement of the ground is called the support, and the part that remains more nearly stationary with respect to more distant unactuated parts of the earth is called the steady mass. The mechanical period of the geophone is the time required for an oscillation of the steady mass after an initial impulse is given it, and is determined by the effective stiffness of the spring joining the two parts together in relation to the weight of the suspended part. Geophones have been used with frequencies varying all the way from less than 10 cycles per sec. to several hundred cycles per second. Those with a natural frequency of less than, say, 100 cycles

Jan 1, 1940

Jan 1, 1967

Jan 1, 1968