Search Documents

By John A. Gann

WITHIN a very few years magnesium has sprung from oblivion, from classification as a technically unknown, little appreciated, and expensive material to front-page importance in many fields of engineering. Bunsen may be considered the real founder of our present magnesium industry. In 1852; he prepared this metal by the electrolysis of fused magnesium chloride in a porcelain crucible. In the following years the electro¬lytic process became recognized as superior to chemical reduction methods and Germany became the world's chief producer, installing the first electrolytic magnesium plant in 1886. ' Thirty years later, national defense requirements, occasioned by the outbreak of the World War and the cutting off of imports, caused France, England, and the United States to begin production. Most of this magnesium was used for military purposes so the close of the war resulted in a large curtailment in production. A few companies, however, encouraged by the early success of the Germans and by the rapid developments taking place in aeronautics, and confident in the certain future and ultimate value of this metal, undertook extensive re¬searches in its production and utilization. A variety of production methods, both chemical and electrochemical, were investigated and some of them operated on a commercial scale. Reduction of the oxide with carbon at high temperatures and the electrolysis of the oxide in a fluoride

Jan 1, 1932

By C. Y. Wen, H. O. HOPMAN

l. INTRODUCTION. IN casting a thermal balance of the heat generated and absorbed in a blast-furnace treating lead-, copper- and similar non-ferrous ores, assumptions have always to be made for the values of the heat of formation of slag. ? Considering that the larger part of the charge introduced into the furnace comes out in the form of slag, the significance becomes apparent of a lack of heat-values for the singulo-silicate, which is the type of slags commonly made. The aim of the present investigation is to supply these heat-values as far as possible with the apparatus and the time available. The heats of formation of the ferrous and manganous bi-silicates have been determined by Le Chatelier; 1 those of some silicates other than iron and manganese by Tschernobaeff:2 finally Richards 3 gives a figure for a copper blast-furnace slag of known composition. The existing data and those resulting from the present investigation are assembled in Table VI. II. MATERIALS USED. The materials used in the experiments were silica, ferrous oxide, and calcium carbonate. Silica.-The silica sold in the market as chemically pure usually contains small amounts of magnesia, lime, and alumina, and is therefore not suited for the work. The pure material was obtained from clear quartz crystals from Arkansas, broken in a diamond mortar and ground in an agate mortar to pass 1 Comptes rendus, vol. cxx., p. 623 (1895); vol. cxxii., p. SO (1896). 2 Revue de Métallurgie, vol. ii., p. 729 (1905); Electrochemical and Metallurgical Industry, vol. iv., No. 2, p. 72 (Feb., 1906). 3 Electrochemical and Metallurgical Industry, vol. v., No. 7, p. 266 furls?, 1907;) ; Metallurgical Calculations, vol. iii.,.pp. 474, 475 (1908).

Jul 1, 1910

By M. B. Riordan

A surface indicating pressure, temperature and flow instrument that ernploys variable frequency sensing elements has proved useful in evaluating flow characteristics of wells. Relative productivity of individual oil and gas sands in a given well can be analyzed at several back pressures. The variable frequency sensing elements are an improvement in sensitivity and accuracy and make possible observation of temperature and pressure variations that have not been possible heretofore. The surface indicating featuere results in a more direct approach to solving problems and eliniinate; many assumptions. All three subsurface factors are evaluated, and correlation between them results in a direct means of analyzing reservoir. and well conditions. Surveys have been used to evaluate well performance. locate gas entry In high ratio wells and to investigate gas injection and water flooding conditions. INTRODUCTION In a flowing well that is open to a multiple number of producing sands with varying characteristics. it is valuable to know which sands are producing fluid at a given back pressure and in what relative quantity. Core studies could qualify an interval as productive, and reserves would be computed on this basis. Unless the well is produced so that the interval does contribute. irreparable damage to the interval can occur. It is generally accepted that the optimum condition of pro-

Jan 1, 1951

By M. B. Riordan

A surface indicating pressure, temperature and flow instrument that ernploys variable frequency sensing elements has proved useful in evaluating flow characteristics of wells. Relative productivity of individual oil and gas sands in a given well can be analyzed at several back pressures. The variable frequency sensing elements are an improvement in sensitivity and accuracy and make possible observation of temperature and pressure variations that have not been possible heretofore. The surface indicating featuere results in a more direct approach to solving problems and eliniinate; many assumptions. All three subsurface factors are evaluated, and correlation between them results in a direct means of analyzing reservoir. and well conditions. Surveys have been used to evaluate well performance. locate gas entry In high ratio wells and to investigate gas injection and water flooding conditions. INTRODUCTION In a flowing well that is open to a multiple number of producing sands with varying characteristics. it is valuable to know which sands are producing fluid at a given back pressure and in what relative quantity. Core studies could qualify an interval as productive, and reserves would be computed on this basis. Unless the well is produced so that the interval does contribute. irreparable damage to the interval can occur. It is generally accepted that the optimum condition of pro-

Jan 1, 1951

By Jonas Svensson

A new method is described for the production of cold-bonded pellets using a hydraulic binder, such as portland cement. Large-scale pilot-plant tests have proved that self-fluxing pellets of high reducibility and good handling strength can be made by the method. Blast-furnace trials have shown that the pellets are an acceptable burden material, comparable with self-fluxing sinter or heat-hardened pellets. Economic factors of commercial-scale production are discussed. The Grangcold Pellet Process—for which patents have been applied or already granted in a number of coun-tries—uses a hydraulic adhesive such as portland cement, slag cements, pozzolanic cements, etc., for the production of cold-bonded pellets. The idea of using a hydraulic binder for the agglomeration of iron-ore fines is not new. Portland cement was proposed as an adhesive for cold-bonded iron-ore briquettes in patents granted more than 50 years ago.' In a report on the briquetting of iron-ore fines, published in Stahl und Eisen in 1959; it is stated that briquettes bonded with portland cement are used on a small scale at an ironwork in Germany. According to the report, the briquettes showed excellent strength in the blast furnace although their general use was made impossible because they required a long hardening time, during which they are sticky, soft, and difficult to store and handle. The Grangcold Pellet Process has overcome this particular disadvantage by mixing the balls with a suitable amount of the balling concentrate before storing them. The pellets are embedded in the concentrated during storing in such a way that they are isolated from each other and thus prevented from sticking together to form clusters. Thanks to the embedding concentrate, the pellets are subjected to a more or less uniform pressure from all sides which does not deform them. Thus, the mixture can be stored in a stockpile or in a bin until the pellets have hardened sufficiently. The concentrate is separated from the pellets by means of screening. The concentrate is returned to the balling operation and the pellets are either shipped to the blast furnace or stored for final hardening. The binder preferred for the Grangcold Pellett Process is portland-cement clinker, ground without the admixture of gypsum in order to avoid sulfur in the pellets as far as possible. Usually a 10% binder content is used. Two-thirds of the portland-cement clinker consist of lime and the rest is silica, alumina, and ferric oxide. Thus, self-fluxing or overbasic pellets are produced with this binder if the amount of silica in the concentrate used does not exceed 4%. The Grangcold Pellet Process was developed by the mineral Processing Laboratory of the Granges Co. Work started in 1963 with batch-scale tests. In 1966, a small pilot plant was put into operation in which 1800 tons of pellets were produced using 10% of rapid-hardening portland cement as a binder. Favorable results from a blast-furnace test with this batch led to the decision to erect a larger pilot plant which went into production in the summer of 1967. Since then, approximately 100,000 tons of cold-bonded pellets have been produced, mostly with 10% gypsum-free portland cement as a binder. Several full-scale blast-furnace trials have been performed with the pellets. The results of the trials indicate that the Grangcold pellets constitute a satisfactory blast-furnace feed. An industrial plant for the production of Grangcold pellets with a rated capacity of 1.5 million tpy is now under construction at the Granges Co.'s mine at Grangesberg. The plant will come into operation in the summer of 1970. Results from Laboratory Work Pellets made from iron-ore concentrate bonded with portland cement harden slowly and their handling is very critical until they have hardened enough to loose their stickiness. It is therefore especially important to study the progress of the hardening action and the factors influencing it. This is best achieved by investigating the relationship between the compressive strength of the cement-bonded pellets and the curing time under varied conditions. The general course of this relation-

Jan 1, 1971

By J. L. Tokich, A. R. Troiano

Since 1921, when Hull1 discovered that cobalt can exist in the face-centered cubic and hexagonal close-packed modifications, the transitions that occur in cobalt have been extensively studied. It is generally agreed that on heating the hexagonal lattice changes to the cubic structure at ternperatures ranging from 400° to 500°C although considerable doubt exists as to the exact temperature. Data concerning the temperature of the transformation on cooling are much less concordant and their interpretation has not been satisfactory. The study is further complicated by the fact that many investigators have reported the existence of a high temperature allo-tropic change in the range 850 to 1020°C, at which the cubic lattice reverts to the hexagonal modification. The transition on cooling, which has been reported as Occurring at various temperatures from approximately 400 to 100°C, is of particular interest. Troiano and Greninger2 have recently suggested and considered the possibility Of allotropic transformations occurring in pure metals by a shear-type, diffusionless (martensite) transformation. The case of cobalt was specifically discussed and certain observations of previous investigators evaluated in terms Of this type of Of Table 1 briefly outlines the methods and results Of previous investigators Of the transformation temperatures of cobalt. Materials and Methods The major portion of this investigatioll was performed with cobalt sheet containing a total of 0.2 pet impurities with carbon present to the extent of o,I pct. After melting in an induction furnace under an atmosphere of hydrogen, the carbon con. tent analyzed 0.03 pct. Some observations were repeated with hydrogen reduced cobalt compresses analyzing 99.9 pet pure. No significant variations in results were observed employing the as-received sheet, the remelted stock, or the cobalt compresses. Filings for X ray diffraction analysis were sealed in evacuated glass ampoules. Pyrex glass tubing was used for temperatures below (600°C and for higher temperatures clear fused quartz was satisfactory. After appropriate heat treatment at various ternperatures, the specimen ampoules were furnace cooled, air cooled or quenched by crushing under distilled water. This allowed a range of cooling velocities from less than one degree C per set to greater than 1,0oo°C per sec. X ray diffraction patterns were taken with a Debye camera and filtered characteristic cobalt K-alpha radiation. The of of the existing phases was roughly approximated by visual examina-

Jan 1, 1949

By J. H. Mallery, J. H. Keeler

THE crystal structure of Zral, the compound richest in zirconium (91.03 pct Zr by weight) in the system Zr-Al, has been found to be ordered face-centered-cubic. This compound is of particular interest, since it is encountered as the precipitated phase in potentially useful zirconium-rich alloys. It forms peritectoidally from body-centered-cubic zirconium and Zr,Al at about 975°C. The Zr-A1 constitution diagram has been reported by McPherson and Hansen.' For the primary determination a 100 g ingot was prepared by arc-melting in a water-cooled copper crucible under purified argon. The raw materials were crystal-bar zirconium (a purity of better than 99.7 pct) and spectroscopically pure aluminum. The ingot was double melted, examined metallographi-cally, and found to be quite uniform as shown in Fig. 1. The hardness of the as-cast button was VHN 390 to 445. A 20 mil diam specimen was prepared from annealed (900°C) filings of Zr,Al. The specimen was mounted in a 5 cm radius powder camera and an 8 hr exposure was taken using copper radiation with a nickel filter. The structure of the compound Zral was found to be ordered face-centered-cubic of the Cuau type, with an a,, value of 4.37220.003A. Its calculated density is 5.976e0.013 g per cu cm. The relative intensities for the lines were calculated using the formula 1+cos2 20 I oc----------------- • p • /F7 sin2 0 cos 0 1 + COS' 20 where----------------is the Lorentz polarization fac- sin2 0 cos 0 tor, p is the multiplicity factor, and F is the structure factor. The X-ray data are given in Table I. The compound has exhibited plasticity when present as particles in a matrix of a zirconium. During hot working at about 900°C, the compound has been found to deform plastically to the extent that some of the particles exhibit a length-to-width ratio greater than 4:1 as shown in Fig. 2. In answer to the discussion of ref. 1, McPherson and Hansen pointed out that the compound may be cold rolled and reduced as much as 33 pct. Zr,Al has also been found2 under certain conditions to precipitate in lamellar form at grain boundaries of the a phase of hexagonal-close-packed zirconium. Acknowledgment This work was carried out under Contract W-31-109-Eng 52 for the United States Atomic Energy Commission.

Jan 1, 1956

By H. C. Brassfield, R. E. Fryxell, E. C. Duderstadt, E. A. Aitken, P. K. Conn

Permeation rates of hydrogen through are-cast tungsten were measured at temperatures from 1300" to 2600°C with hydrogen pressure differentials of 1 and 0.1 atm across isothermal membranes. Rates were nearly Proportional to square root of pressure, were inversely ProPortional to membrane thickness, and were temperature-dependent according to the equation: p = permeation coefficient in cu cm (stp)-mm per sq cm-min-atmlr2, R = gas constant in cal per mole-OK, T = absolute temperature in OK. Permeation rates of oxygen through tungsten were deternlined in the range 1965" to 2300°C and at calculated oxygen (02) pressures of 3.3 x 10-4 to 2.2 x at?n using sealed capsules containing Kmown quantities of tungsten oxide. Permeation coefficients obtained in this manner had a temperature dependency in the range of 40 to 45 kcal per mole of permeating species. Permeation coefficients for oxygen were higher than those for hydrogen in the temperature range studied. This is probably the result of oxygen solubility being much greater than hydrogen solubility at these temperatures at a gzven pressure. The purpose of this investigation was to determine experimentally the permeabilities of hydrogen and oxygen through polycrystalline tungsten at temperatures ranging from 1300° to 2600°C. Permeation rates of hydrogen through tungsten have been measured at temperatures up to 925°C,but no previous measurements have been reported for the temperature range covered in this investigation. Some diffusion measurements3&apos;&apos; and solubility measurements3 have been made for hydrogen at temperatures below 2200°C. No previous permeability studies of oxygen through tungsten are known to the authors; however, efforts have been made to determine diffusion rates5-&apos; and solubilities PERMEATION THEQRY Permeation has been defined by ortton" as the overall steady-state flow process from the gas phase on one side of a membrane or wall to the gas phase on the other side and includes the steps of adsorption, solution, diffusion, exsolution, and desorption; in a given temperature range, any of these processes may be rate-controlling. For diatomic gases, which dissociate prior to diffusion, the quantity of gas which permeates through a membrane or wall at a given temperature is directly proportional to the surface area of the membrane, the length of time of permeation, and the difference between the square roots of the pressures on each side of the membrane, and it is inversely proportional to the thickness of the membrane when diffusion-controlled, thus: q = total amount of gas permeating a membrane, p = temperature-de pendent permeation coefficient, A = area of membrane exposed, / = time, p i = gas pressure of high-pressure side, p2 = gas pressure of low-pressure side, d = thickness of membrane. When the surface reactions are not rate-controlling steps and the solution of the gas in the metal follows Henry&apos;s law, the permeation coefficient, P, is equal to the product of diffusivity and solubility. The permeation coefficient is also temperature-dependent according to the equation: Po = permeation constant, Q = activation energy, R = gas constant, T = absolute temperature. MATERIALS The tungsten materials used in this investigation were greater than 99.9 pct pure. The interstitial impurities ranged from < 1 to 50 pprn C, 7 to 35 ppm O, less than 15 pprn N, and undetectable quantities of hydrogen. Previous high-temperature studies of are-cast tungsten have shown that thermal treatment similar to that which the hydrogen permeation cells experienced reduces the carbon content from starting levels of 50 to 60 ppm to about 30 ppm. Metallic impurities were in the low (1 to 50) ppm range. The argon gas used in this investigation contained about 8 ppm N. None of the following gases were

Jan 1, 1968

By I. N. Zavarine

AUSTENITE is often defined as a solid solution of carbon or carbide in a nonmagnetic form of iron. Conversely, magnetic measurements are often used by investigators for the purpose of detecting the degree of austenite decomposition after an iron alloy has been subjected to certain thermal or mechanical treatments. Association of the magnetic state with the gamma-phase decomposition is often extended to the alloys of iron with elements other than carbon. Definition of austenite as a nonmagnetic solid solution cannot be accepted in the light of available information without certain reservations. The relation of magnetic transformations with the gamma-phase decomposition in the complex alloys of iron has never been rigorously proved. The present investigation deals primarily with the magnetic trans-formation that occurs in carbon steels during the quenching process. The work was further limited to a study of magnetic transformation in carbon steels quenched at such rates as are necessary to retain the product of austenite decomposition in a martensitic state.

Jan 1, 1934

By Eugene Leonardon

THE search for oil has required, and without a doubt supplies, a tremendous amount of information on the structure, composition, physical properties, and history of sedimentary rocks. The earliest and most complete source of knowledge is the sample or core of the rock itself, the uses of which are well known. The purpose of this paper is primarily to discuss a new method for obtaining these cores, and to illustrate its use in connection with electrical logs. Most cores have been obtained through a special adaptation of rotary drilling, and the results have been remarkably good, considering the mechanical problems involved. Unfortunately, because of the time and expense, this method cannot be used for the entire length of the drill hole. Even though ingenious contrivances have been evolved in order to reduce the time spent in round trips, such as wire-line coring equipment, mechanical coring still remains too expensive to be carried out con-tinuously. In practice, therefore, one is finally compelled to estimate the probable depths of the more interesting horizons and, allowing a wide margin of safety, to core through those sections only. It is true also that interesting results have been obtained by examining the cuttings brought to the surface by the mud circulated in the well during the process of drilling. Be that as it may, the inescapable fact remains that key horizons may be passed inadvertently, for one reason or another, while the drilling operations are being performed. The only continuous record of the formations encountered is that furnished by electrical surveys. Obviously, it would be desirable to make the electrical survey first and to take the samples from the wall of the hole according to the indications on the electrical log. In this way, it would be possible to core only the exact sections desired, eliminating the otherwise inevitable estimates as to the point at which to start coring, and thereby reducing to a minimum this expensive operation. At the same time this method would provide a maximum&apos; of useful samples.

Jan 1, 1939

By Eugene Leonardon

THE search for oil has required, and without a doubt supplies, a tremendous amount of information on the structure, composition, physical properties, and history of sedimentary rocks. The earliest and most complete source of knowledge is the sample or core of the rock itself, the uses of which are well known. The purpose of this paper is primarily to discuss a new method for obtaining these cores, and to illustrate its use in connection with electrical logs. Most cores have been obtained through a special adaptation of rotary drilling, and the results have been remarkably good, considering the mechanical problems involved. Unfortunately, because of the time and expense, this method cannot be used for the entire length of the drill hole. Even though ingenious contrivances have been evolved in order to reduce the time spent in round trips, such as wire-line coring equipment, mechanical coring still remains too expensive to be carried out con-tinuously. In practice, therefore, one is finally compelled to estimate the probable depths of the more interesting horizons and, allowing a wide margin of safety, to core through those sections only. It is true also that interesting results have been obtained by examining the cuttings brought to the surface by the mud circulated in the well during the process of drilling. Be that as it may, the inescapable fact remains that key horizons may be passed inadvertently, for one reason or another, while the drilling operations are being performed. The only continuous record of the formations encountered is that furnished by electrical surveys. Obviously, it would be desirable to make the electrical survey first and to take the samples from the wall of the hole according to the indications on the electrical log. In this way, it would be possible to core only the exact sections desired, eliminating the otherwise inevitable estimates as to the point at which to start coring, and thereby reducing to a minimum this expensive operation. At the same time this method would provide a maximum&apos; of useful samples.

Jan 1, 1939

By H. Rumfelt

The author demonstrates an approach for analyzing overcasting requirements for a stripping project. This approach to the problem employs indicated trends in the relationship of the weight of the machine (only electropowered draglines are considered) to its ability to do stripping work. Strip mining in the domestic coal industry is contributing a greater proportion of overall production than at any time in the past. U.S. Bureau of Mines statistics show that the percentage of total production mined in 1958 by stripping methods increased to more than 30 pct, up from 22 pct in 1951. The tendency to favor strip and open pit mining exists in other mining activities, but such trends are not as clearly outlined as in the coal industry. Significantly, the depth of overburden in coal properties considered suitable for stripping is also increasing. A depth of 50 to 60 ft of overburden was once considered to be about the maximum amount that could be handled economically. Today, a depth of 80 to 100 ft is frequently taken into consideration for simple overcasting operations (i.e., excavating overburden and dumping it in the spoil position where it remains indefinitely). Accompanying these changes, there have been continuing studies searching for procedures to appraise deeper stripping problems. Although the only known practicable way to accurately evaluate a proposed stripping venture is to make studies (including cost estimates) step by step, it is nevertheless desirable to have a quick method for making preliminary evaluations of potential strip mining operations. A recently devised digital computer method of providing a preliminary simple overcasting analysis for a stripping prospect relates the indicated trends in the relationship of the weight of the machine to its ability to do stripping work. In addition, this approach employs situations where the geometry of each cut-and-spoil section is assumed to take certain defined relationships for varying overburden depths. Slopes are necessarily considered to be stable, which means such practical factors as the mechanics of soils are neglected for the sake of convenience. Definition of Terms: Photographs A and B show a shovel-type and a dragline-type of simple overcast operation, plus terms used to denote certain parts of a pit. Pits that follow a straight line when projected on a horizontal plane are referred to as straightaway. It has been assumed that all section drawings accompanying this article pertain to straightaway cuts which, in turn, means that areas can be compared by relative volume. The volume of overburden is measured in virgin cubic yards. Material displaced from its virgin state to a spoil area normally occupies a larger volume than when in situ; the difference is termed swell, and it is expressed as a percentage of the original volume. For example, if the original cut volume is denoted V cu yd, and the spoil volume is 1.2 V cu yd, the swell is a positive 20 pct. MAXIMUM USEFULNESS FACTOR (MUF) CONCEPT Men experienced in overburden removal give emphasis to the weight of the machine in relation to its value as an excavator. From the writer&apos;s understanding, value has been only loosely defined and discussed generally and vaguely. The concept is considered important, however, since it is based upon the observations of many men. It provides a clue for the approach taken to solve deep stripping problems. In the procedure described below, value has been arbitrarily established as the product of the nominal dipper size of the shovel (or dragline) times a functional dumping reach. MUFs—Shovel: A shovel&apos;s capability to handle thick overburden is usually limited by its ability to dispose of the spoil. Thus the dumping reach, as well as its dumping height, is significant. The angle of repose of spoil material must also be considered. Although such slope angles vary among different mines, jobs, and materials, a slope of 1.25 to 1, frequently found in both planning and practice, is used by this author in the illustration of this analytical method. The relationship of the shovel&apos;s geometry to a stripping operation is shown in Fig. 1. To gain maximum advantage in constructing spoil piles, the shovel is placed so that its tracks adjacent to the spoil are as close as possible to the rib of the coal deposit. A vertical plane passing through the line

Jan 1, 1961

By T. P. Papazoglou, N. A. D. Parlee, W. C. Phelps

HE high vapor pressures of metals such as lead, calcium, lithium, bismuth, and magnesium at steel-making temperatures present experimental problems which have thus far rendered it almost impossible to obtain really reliable data for their solubilities in liquid iron. Many investigators have attempted to equilibrate liquid iron in the same crucible with the undissolved liquid phase of such volatile metals. The published results,l-6 although useful, are often questionable on the grounds of not being obtained under true equilibrium conditions. Such information is not always of practical value in any case since the equilibrium vapor pressure is often several atmospheres and steel is not currently made at these pressures. Solubility measurements at lower partial pressures (< 1 atm) appeared to be more practical and easier to make. These data could be used to calculate solubilities at other pressures where Henry&apos;s Law is obeyed, and to estimate solubilities under other conditions of temperature and pressure with useful accuracy. This note outlines the development of a general technique for the measurement of solubilities in systems of this kind. The method involves equilibration of the high-boiling metal at known temperatures with the vapors of a low-boiling metal at known partial pressures. Analyses of quenched samples provide vapor pressure-solubility data and make calculations of alloy thermodynamics possible. The principle involved is similar to the closed-system diffusion-transport method which is difficult to apply with most high-melting liquid metals like iron, due to closure problems. A two-zone horizontal (molybdenum wire element) tube furnace, Fig. 1, provides two constant-temperature zones in a reaction tuve (3/4 in. ID by 1 in. OD by 36 in.). A high-boiling metal sample, 9, introduced in the higher-temperature zone, is maintained at temperature T1, and a volatile metal sample, 7, in the lower-temperature zone, is held at T2. A stream of argon with 10 pct hydrogen is passed via flowmeters, 1, and mixing-drying towers, 2 and 3. through the reaction tube at a favorable flowrate and acts as a carrier gas which entrains vapor from the volatile liquid metal at a specific constant partial pressure. The gas mixture passes through a system of constrictions, 6 and 8, to the higher-temperature zone, establishes intimate contact with the high-boiling liquid sample, 9, and exits through a small condenser tube. The entire system is at (nearly) atmospheric pressure and the volume of carrier gas passed is measured with a wet gas meter. When the high-boiling sample attains equilibrium with the vapor phase, both samples are removed and quenched. Analysis of the high-boiling sample for solute content reveals its solubility for the low-boiling metal at a vapor pressure calculated from carrier-gas volume and either a) weight loss of volatile metal or 6) weight gain of high-boiling sample plus condenser (which collects the undissolved vapors). To test the capabilities of the method, liquid silver at 1403&apos;C was equilibrated with lead vapor at various partial pressures. The relatively simple Pb-Ag system was particularly suitable for uncovering experimental problems and providing the first step toward investigations with more volatile metals and more difficult combinations.

Jan 1, 1965

By Walter Miller

ALTHOUGH confident of its ability to meet any demands which may be made, the petroleum refining industry is not complacent about the situation and realizes that the quantities of petroleum products to be furnished are so enormous and so far beyond what was previously estimated that the full co-operative effort of the industry must be exerted. Establishment by the President in May of the Office of Petroleum Coordinator for Defense with Secretary of the Interior Ickes at its head, plus the formation of the Petroleum Industry Council for Defense, in November, provide the channels for united endeavor within the industry and the means for gearing that endeavor within the industry and the means for gearing that endeavor in full harmony with the nation?s needs. Great strides have been made and a rapid understanding of the situation and the magnitude of the task is being attained by all concerned.

Jan 1, 1942

By N. M. Langdon

In considering the magnificent success of Mr. Gayley&apos;s bold experiment of applying dry blast to the blast-furnace, whereby a saving of 20 per cent. of fuel per ton of iron is effected, the question arises whether still further economy in fuel is possible, and, if so, how it is to be attained. The manner in which the heat generated in the furnace is utilized in the production of pig-iron may be determined, by the method of Bell and Gruner, for any furnace for which the necessary data are obtainable ; and the study of the operation, under various conditions, of a number of furnaces, for which such information has been worked out, should enable us to form some conclusion on the subject. The tables and calculations here given cover the operations of several furnaces reported in our Transactions ; also the two furnaces using natural and dry blast ill Mr. Gayley&apos;s experiment, for which the heat-equation has been worked out by Prof. Joseph W. Richards in his admirable discussion &apos; of Mr. Gayley&apos;s paper, The Application of Dry Air Blast to the Manufacture of Iron, and, finally, various hypothetical furnaces. The full list is as follows : A. Isabella furnace, with natural blast. B. Isabella furnace, with dry blast. The data stated for A and B in Table 111. are those given by Professor Richards, except that the heat-units are given for one unit of iron instead of 100 units, and some items of heat supplied, as stated by Richards, have been subdivided, the total being the same as given by Richards. (Columns A and B are introduced in Table 111. for comparison with C and D.)

Jan 1, 1910

By L. B. Slichter

IT has been estimated that rock exposures in most mining districts aggregate less than 1 per cent. of the total surface area.1 Conclusions concerning the hidden 99 per cent. necessarily have been based on knowledge of only a small fraction of the surface, and from this limited information the geologist has been obliged to deduce the approximate and general nature of the underlying formations. In the search for ore it is necessary to supplement this general picture with greater detail. Fairly accurate knowledge of relatively small zones is required. This knowledge is carefully sought in many different ways-detailed interpretations of geological history, the tracing of float, the use of test pits, of trenching, of drilling, and of other methods. Practical ingenuity, scientific brilliance, great perseverance and patience, and the expenditure. of large sums of money have all been a part of this search. The problem of exploring beneath cover with economy, and of obtaining essential information which this cover hides, is obviously a difficult one. It is also a very important one, for geologists inform us that already the story of the 1 per cent. exposed outcrops has been largely read.2 There remains the nearly virgin field comprised in the hidden 99 per cent., and the importance of this zone is bound to increase continually. In recent years, the problems connected with the exploration of this "99 per cent. zone" have attracted a constantly enlarging group of investigators and at present greater efforts than ever before are being made to resolve then. This work, in its various special aspects, has enlisted, beside geologists, the cooperative efforts of chemists, physicists, and mathematicians. The progress made in this development should be kept before those directing explorations in order that due advantage may be taken of a changing situation.

Jan 1, 1928

By C. R. Fulton

The idea of making permanent magnets by sintering is not a new one, but until the introduction of the iron-nickel-aluminum permanent-magnet alloys there was little need for such a process. Permanent-magnet alloys in use up to the time of this development could be forged and machined to the exact size or shape required without too much difficulty. These new Fe-Ni-A1 alloys, which have become known as Alnico in this country, soon became very popular because of their superior magnetic properties, but when they were made by casting they did have some disadvantages when compared with the older type of permanent-magnet steels. Among these disadvantages were the following: 1. It was almost essential that they be cast to size, since they could not be readily forged or machined. The material could be ground but this was quite expensive, particularly for small magnets in large quantities. 2. The material had a large grain size and was mechanically weak. 3. Close tolerances could not be held and on small magnets this meant grinding almost the entire magnet. Because of the brittle nature of the material, there was considerable loss due to chipping and cracking during these grinding operations. 4. Because of its high aluminum content, the molten alloy had a high surface tension. It was difficult to prevent loss of aluminum by oxidation during the melting operation. In view of these difficulties it is not hard to understand why a process for sintering alnico was developed, or why sintered alnico has come into such widespread use in recent years. It might be well to qualify this by saying that it has come into widespread use for small magnets weighing 2 oz. and less, of the type shown on Fig. I. In this size range, sintered alnico has been able to compete in price with cast alnico. Magnets larger in size, of the type shown on Fig. 2, can be made but they do not compare favorably in price with the cast material. An idea of the range of sizes that have been produced is given by Fig. 3, which shows a small magnet weighing 0.006 oz. and a large magnet with a steel insert weighing 4 lb., both made from sintered alnico. Magnets weighing more than 2 oz., however, should not be made from sintered

Jan 1, 1945

By Harry C. Wiess

RECENT announcement of further restrictions on gasoline consumption in the Mid-West and Southwest has focused public attention on current discussions of an oil scarcity. Conflicting arguments are advanced on the one hand that we have plenty of oil and will not need to restrict consumption as soon as transportation facilities are adequate, and on the other hand that a great impending shortage will require most drastic reductions in civilian consumption in order to provide adequate supplies for military purposes. Data can be presented to support both views, the result being that the public is confused and uncertain of where the truth lies. For a nation with about half of the known crude-oil reserves of the world and two thirds of the total production it seems almost incredible to the layman that any shortage can exist. Those familiar with estimates of future demand. however. show increasing concern regarding our ability to meet military demands without further restrictions in civilian use or wasteful production from our remaining reserves. Only by considering such facts as are available and can be made public can a true appraisal be made of whether or not we are faced with a shortage that will amount to a crisis in crude oil.

Jan 1, 1943

By A. L. Holley

THERE are regularly manufactured in the eleven Bessemer steel rail mills of the United States, 119 patterns* of steel rails, of 27 different weights per yard. This list does not include patterns which, although still largely inn use, are regarded by experts as obsolete, and which would swell the number to nearly 300; nor does it include all, the patterns for which rolls are kept on hand to fill a possible demand; nor does it include extra pattern,- rolled in one finishing groove by opening or closing the rolls so as to get different weights with the same contours. The list embraces only those separate patterns which are subject to current orders. How thoroughly modern these patterns are, is shown by the fact that of the whole 119, there are but five patterns of conspicuously bad shape; all the rest more or less completely illustrate the standard features,-a heavy bead,. light web and flanges, and a good angle :to hold the fish-plate. Sixty-two per cent. of the patterns have the "Chanute" head, which was not designed until 1874.† Sixty-four per cent. of the 119 patterns are embraced under five weights per yard,; three only of these vary from standard type; there am thus 76 patterns, all of them modern and standard, to represent five different weights, for which five patterns would perfectly answer. Of the 60-lb. rails, there is only one of the pear-head type, while a dozen of the bevelled head templets cannot be distinguished from each other * From all the works 188 patterns were sent to me as standard. Of these I found 119 different shapes and 69 duplicates. † Since this paper was read I have seen at the Bethlehem Iron. Works the templet of a 68-pound Lehigh Valley rail, with the bevelled head, usually called the "Chanute" head, and marked "Templet of 1872." This is shown on Plate II. I learn that iron rails, with bevelled heads, were rolled at Bethlehem prior to 1870.

Jan 1, 1881

By Ernest F. Burchard

The Pao deposits of iron ore are in the State of Bolivar, Venezuela, near Upata, about 30 miles south of the Orinoco River and 90 miles east of Ciudad Bolivar. They were discovered 4 or 5 years ago and have not yet been developed to the stage of mining. In March-April, 1929, the writer devoted a week to the examination of these deposits. The maps, drill records and chemical analyses presented herewith were derived from original sources, and the field photographs were made by the writer. The petrographic and metallographic data are from notes by C. S. Ross and M. N. Short, of the U. S. Geological Survey, who have kindly collaborated in these special phases of the study. The Iron Obebodies Topography and Accessibility The deposits are in a region of low mountains representing northern outliers of the Guayanan Highlands. These mountains reach altitudes of 1800 to more than 2000 ft. above sea level, as determined by aneroid barometer. The iron ore is found on mountain crests that reach altitudes of 1915 to 1930 ft., and may be followed down precipitous slopes for 200 • to 300 ft. or more. The greatest vertical range in outcrop is nearly 400 ft., and drilling has indicated that the ore extends to this depth below the surface in one place, at least. The superior hardness of the iron ore accounts for the preservation of the local mountain crests with the intermediate valleys eroded in softer granitic rock. The deposits of iron ore are reached by a private road for automobiles branching northeast from the Ciudad Bolivar-Upata road, a distance of about 12 miles. This road was used in 1928-29 by trucks for transportation of food and camp supplies, gasoline, drilling equipment, etc., but was not suitable for the transportation of iron ore. Between Ciudad Bolivar and the iron-ore area the western two-thirds of the automobile road passes through nearly level, open country known as the savanna, largely used for grazing cattle. About 96 km. (60 miles) east of Ciudad Bolivar at

Jan 1, 1931