Search Documents

E. H. Dix, JR., Chairman L. W. M. PEIRCE, Past-chairman R. F. MEHL, Vice-chairman ALBERT J. PHILLIPS, Vice-chairman E. M. WISE, Secretary International Nickel Co., Bayonne, N. J. W. M. CORSE, Treasurer LOUIS JORDAN, Executive Secretary 29 West 39th St., New York, N. Y. Executive Committee W. H. BASSETT, JR. R. H. LEACH' W. H. FINKELDEY W. E. REMMERS2 J. A. GANN H. J. ROAST G. O. HIERS C. S. SMITHS L ZICKRICK

Jan 1, 1936

By W. J. Putnam, H. F. Moore

THIS paper gives a preliminary summary of results of tests on the resistance to fatigue under reversed stresses of steel subjected to cold-working and of tests to determine the effect of rest on the endurance of steel under reversed stresses. The tests of cold-worked steel were undertaken as part of an investigation by the National Research Council Committee on Fatigue Phenomena of Metals and were made by Mr. Moore; the tests to determine the effect of rest are part of an investigation now being made by Mr. Putnam. Both series of tests were made in the Materials Testing Laboratory of the University of Illinois. The preliminary results of these tests are reported now because it is believed that test data on fatigue strength should be available at the earliest possible moment; however, it should be clearly kept in mind that this paper gives preliminary results and is intended to encourage discussion rather than to give final conclusions. Before giving the data of the tests, the writers will explain the term "fatigue strength" as used in this paper and will discuss briefly the method used in interpreting the test data of repeated-stress tests. " The term fatigue strength, as applied to a material, may be defined as that maximum fiber stress that will cause fracture of the material after the repetition of any given number of cycles of stress, each cycle involving the variation of stress from a minimum to the above maximum. The fatigue strength, then, varies with the number, of repetitions occurr,ing in the lifetime of a structural or machine member and with the range of stress for each cycle of stress. The fatigue strength will be lower for a member in which the stress is completely reversed than for one in which the stress varies from zero to a maximum. In interpreting test data from fatigue tests under reversed stress, the stresses and corresponding numbers of repetitions required for failure are plotted on logarithmic cross-section paper. In 1910, Professor

Jan 1, 1920

By J. P. Heller, H. B. Bradley, A. S. Odeh

A potentiometric model technique is presented for determining the areal sweep efficiency of a five-spot well pattern, at and beyond breakthrough. A sharp interface between displaced and displacing fluids is assumed. Although the prototype svstem is referred to as a waterflood operation, obvious changes in the notation and computations will adapt the results to other displacement processes. The results of the study include the following. 1. Areal sweep efficiencies for a five-spot well pattern, at and beyond breakthrough, for mobility ratios (displacing to displaced fluid) of 4:1, 2:1, 1:1 and 1:4. 2. Extension of potentiometric analysis to the investigation of the areal sweep efficiency beyond breakthrough in a five-spot pattern by the application of conformal mapping and conductive-solid models. 3. The use of layers of conductive fabric in representing mobility ratio changes in potentiometric models. 4. The development of a probe mechanism for probing conductive solids. The results obtained by conductive-cloth models agree with earlier areal sweep efficiencies at breakthrough obtained by Aronofsky and Ramey 1 on the potentiometric analyzer using electrolytic-tank models. Results beyond breakthrough differ from those obtained by the X-Ray Shadowgraph technique. Data from this study show that, for mobility ratios greater than one, water cut rises rapidly as fluid is produced after breakthrough. However, for mobility ratios smaller than one, a large increase in area swept resulted with only a small increase in water cut. INTRODUCTION In calculating reservoir performance of waterflood-ing operations and other fluid-injection programs, it is necesssary to estimate the areal sweep efficiency * before and after injected-fluid breakthrough into production wells. Influence of mobility ratio on oil-production history, before and after breakthrough for a five-spot well pattern, has been studied by X-Ray Shadowgraph techniques 2-5 and by gelatin models.6 In none of these investigations was the transition zone controlled experimentally. Steady-state anaiog techniques assume that a vertical and discrete interface exists between the displacing and displaced phase. Thus, when using a potentiometric analysis, it is assumed that no transition zone exists. To determine the areal sweep efficiency beyond breakthrough for a five-spot well pattern using the potentiometric analyzer, four principal problems had to be resolved. These were the following. 1. The laborious method of representing changes in mobility ratio in electrolytic tanks by means of contoured wooden blocks. 2. Vapcrization of the electrolyte solution during the study causing concentration changes and, thereby, variable conductivity. 3. The scale-limitation problem 7 that is accentuated by abrupt eiectrolyte depth changes. 4. A wellbore geometry problem. EXPERIhlENTAL EQUIPMENT AND PROCEDURES CONDUCTIVE-SOLID MODEL The theory, equipment and procedural techniques of the electrolytic-tank potentiometric model have been treaced excellently by Lee8 and by Muskat.9 By the use of a conductive solid to represent the fluid conductivity of the porous media, the need for contouring wooden blocks to represent mobility ratio was eliminated. It was found that a carbon-black coated fabric, Uskon D-16,** could be employed as a fairly uniform conductive media. This material, when stacked in appropriate layers and pressed together, can be used to represent changes in mo-

By Mazany, M. S.

THE Caletones copper smelter of the Braden Copper Co. is in the " Teniente" mining district about SO km. (49.7 mi.) southeast of Santiago, Chile. From the seaports of San Antonio and Tralparaiso, the property is reached via the Chilean State Railway (66-in. gage) to Rancagua, whence the Braden railroad (30-in. gage) leads to the smelting plant at Caletones, 60 km. away at 5100 ft. elevation, and continues on to the mine and concentrator at Sewell, at 7000 ft. elevation, 12 km. farther into the Andes. The smelting plant was completed and put into commission in February, 1922. At the start, it smelted daily 750 tons of concentrates produced at Sewell from 10,000 tons of ore; later, its capacity was increased to 900 tons of concentrates from 12,000 tons of ore per day; and it is now being increased to 1100 tons of concentrates from 15,000 tons of ore per day. The smelting plant production is governed chiefly by the

Jan 1, 1925

By W. M. Weigel

Economic deposits of barite occur in Missouri in two main districts. The most important, the Southeastern or Washington County district, is in the southeastern part of the state, mostly in Washington County with a small extension into the northeastern part of St. Francois County. Roughly, it embraces nine townships or about 200,000 acres and accounts for from 80 to 90 per cent. of the state production. The Central district, is in the central part of the state, includes most of Morgan and Miller counties, and parts of Camden; Benton, Moniteau and Cole counties. The area embraced is much larger than the Washington County district, but the deposits are more infrequent. The location and general area covered by the two districts is shown in Fig. 1. There is another small area in southern Franklin County but so far its production has been of small consequence. It might be considered as a northward extension of the Washington County field. An, area in the central part of Hickory County has also produced a small amount. The outline of the districts as shown indicates the general area in which deposits have been found. The total area covered by deposits of barite is only a small part of this, as, in the Central district especially, there may be miles of supposedly barren areas between ore-bearing areas of an acre or two in extent. The date when barite was first mined in Missouri cannot be definit stated, but the industry probably dates back to about 1860. The occurrence of barite was known long before this, as it was encountered in the lead mines in Washington County and mentioned by several earlier writers." Missouri is reported as producing 8000 tons in 1882 so it is evident the industry was well under way in the seventies in order to have arrived at this substantial production. By 1893 Missouri production had increased so that it ranked with that of Virginia, then the largest producer it increased until in 1914 Missouri accounted for about 65 per cent. of the total United States output.

Jan 1, 1929

By Gerard Matthes

Only in recent years has any practical headway been made in the application of aerial photography to geological problems, and up to the present time its principal value to the geologist and mining engineer has been in "areal geology;" i. e., the study of formations as revealed at the surface. The object of this paper is to set forth briefly the principal advantages that may be derived from aerial photographic data in geological work and to serve in a measure as a guide to those who may be contemplating its use. Geophysical prospecting has for object the locating of mineral under the surface. Inasmuch as the geologist's chief complaint in life is a dual one—inability to see under the surface and inability to visualize comprehensively what he does see on top of the ground—geophysical prospecting coupled with aerial photography should do much to lessen his burdens. To what extent aerial photography can be made a useful adjunct to geophysical prospecting remains to be proved, but the inference drawn here is that it holds many alluring possibilities. To avoid disappointments, it should be stated at the outset that to the geologist or mining engineer an aerial photograph or mosaic is only a tool, the efficient use of which he must set out to master. Upon his skill and ingenuity in applying it to particular problems will depend largely the value of the results that he will obtain. Under the most favorable conditions an aerial mosaic, or even a few loose photographs, because of the exceptionally comprehensive oversight which they afford of field data, such as dips and strike observations at isolated outcrops, local indications of faulting, mineral and fossil finds, greatly facilitate study and correlation, save much tedious foot work, and may repay their cost many times. Even so, types of country may be found where the most skillful use of the best of pictures will produce results so meager as to render the cost of aerial photography entirely unwarranted. Between these two extremes will be found endless variations and possibilities. Hence no set rules can be promulgated. The safest procedure is to treat each case as a separate problem and to carefully weigh the relative advantages and shortcomings of aerial photography before embarking on its use.

Jan 1, 1928

By Paul Beck

WHILE the recrystallization properties of most of the practically important metals are known in considerable detail, those of lead are still relatively little known in spite of some valuable contributions in recent years. This condition probably is due to the difficulties involved in applying the usual methods of investigation. The microscopic method of discriminating between the elongated deformed grains of the familiar lenticular shape and the equiaxed recrys-tallized grains is not successful with fully refined lead: lenticular grains cannot be seen under the microscope with any amount of deformation whatever. The probable cause of this phenomenon was recognized long ago. With large deformation the time of recrystallization at room tem-perature is shorter than the period of preparation of the specimen for microscopic examination; with small deformation the deformed grains are not noticeably elongated in the first place. However, with small deformation the migration of the grain boundaries can be observed. The only systematic investigations yet published on the recrystallization of lead, those by R. S. Russell,1-3 make use of the conditions just described. Russell considered recrystallization completed when no further migration of boundaries could be observed. A serious objection to this method arises from the fact that there is no evidence to support the view that grain-boundary migration results only from recrystallization. If such migration does result from other sources after recrystallization is com-pleted-after the deformed grains have been replaced by new unde-formed grains-the "time of recrystallization" as determined by Russell may be too long. Furthermore, the method is subject to the above-mentioned limitation because of the unavoidable period of preparation of the sample. According to Russell, even with the fastest technique 5 min. elapsed before the deformed samples were ready for examination, and consequently no recrystallization time shorter than 5 min. could be measured.

Jan 1, 1939

APPROXIMATELY 90 per cent of the steel that is melted and refined in the United States and poured into ingots is made in basic open-hearth furnaces, as shown in Table 1-1. The annual ingot capacity of the steel industry reported January 1, 1950, by the American Iron and Steel Institute3* was 99,040,160 tons, of which the basic open-hearth process accounted for 85,896,580 tons, 86.7 per cent of the .total. The capacity of the individual furnaces varies over a wide range, a large majority falling within limits of 50 to 200 tons (Fig 1-1). Most of the units constructed [ ] since 1942 are in the larger size groups, between 175 and 225 tons capacity.

Jan 1, 1964

By C. E. Lawall, C. T. Holland

When this study was started very little information was available regarding the physical characteristics of West Virginia coals. This was particularly true of friability and of crushing strengths of the coals. Some work had been done on specific gravity studies but the available information applied to only a few coals. In practically all coal-classification systems thus far proposed, the predominating factors of classifications are largely based on the chemical characteristics of the coal. Recently some investigators have pointed out that a classification based on chemical and physical properties of coal might serve to place coals in their proper group better than classification systems based on chemical properties alone. One of the aims of this study was to obtain some data on the physical properties of coal which might help to classify West Virginia coals. The Samples Fig. I shows where the coal samples were obtained and the approximate division line of the high and low-volatile coal fields of the state. The relative geological horizons of the coal beds tested are shown in Fig. 2. In securing samples of coal for friability and specific gravity tests, it was the aim always to obtain a representative sample of lump coal produced at a particular mine. The samples were obtained from the loading boom, the railroad car, or the mine cars. Wherever it was possible to secure samples from a loading boom they were taken from it by taking shovelfuls of coal from the loading boom every minute until about 200 lb. of coal was obtained. If there were no loading booms used at the mines sampled, the coal sample was taken from a loaded railroad car by systematically taking shovelfuls of coal at definite intervals over the whole top of the car until about 200 Ib. of coal was obtained.

Jan 1, 1932

By R. M. Hardgrove

Pulverized coal was first used for firing cement kilns about 45 years ago, with such success that it has continued in general use. Based on cost, pulverized coal is usually the most economical fuel. In some localities natural gas or oil is cheaper, but 85.5 per cent of all cement kilns at present are fired with pulverized coal. The pulverized-coal flame is well suited to kiln conditions. Its soft, luminous nature gives it a high radiating property and the length of the flame can be readily varied to suit conditions in a kiln of any length. Ash and slag cause most of the dificulties incident to the burning of coal. In a. cement kiln, however, the ash, being similar in composition to the raw mix and being deposited uniformly in the mix and clinker, occasions no difficulty as long as it remains constant in quality and quantity. Until 6 years ago almost all cement kilns using pulverized coal employed the bin system. The coal was dried and pulverizeti in a separate plant and delivered into a bin at the kiln. Thus the bin system requires driers, storage-type pulverizers, conveying systems, individual kiln bins, pulverized-coal feeders and primary air fans. The direct-fired system requires only a pulverizer and a blower. Fig. I shows typical plants. The first installations of direct-fired pulverizers were of the impact type but fineness of pulverization was both inadequate and variable. About 1927 a few direct-fired installations employing tube-type pulverizers were made, which were much more satisfactory. As more efficient pulverizers were developed from 1934 on, equipment for direct firing was installed at a large number of plants, until now 196 of about 900 kilns in use in the United States are direct-fired. Most of these replaced antiquated bin systems. Process of Burning Cement Clinkers The process of burning cement clinkers is fundamentally one of heat transfer. In boilers and other heat-exchange apparatus the area of the surface receiving heat from the gases is the best unit for comparing output, This seems to be equally true for kilns. The inside kiln surface is the heat-receiving surface and its area is used as the unit of kiln size in the following comparisons. Heat input is based on British thermal units in the fuel. E. G. Bailey,' in his work on boiler-furnace heat absorption, has used the unit "B.t.u. available." This is the practical calorific power of the fuel, plus the heat in the air used for combustion. In other words, it is the heat available for useful work in the furnace or kiln. The unit of kiln output is barrels per hour. The composition of the raw mix, the percentage of water in the slurry of wet plants and hardness of burning all affect the output. These conditions, however, are hard to evaluate and probably have less effect on the output than irregularities of raw feed and clinker discharge and inexpert control of combustion. Wet vs. Dry Plants The study presented here covers 88 plantsl of which 41 are wet and 47 dry. Of

Jan 1, 1942

By R. M. Hardgrove

Pulverized coal was first used for firing cement kilns about 45 years ago, with such success that it has continued in general use. Based on cost, pulverized coal is usually the most economical fuel. In some localities natural gas or oil is cheaper, but 85.5 per cent of all cement kilns at present are fired with pulverized coal. The pulverized-coal flame is well suited to kiln conditions. Its soft, luminous nature gives it a high radiating property and the length of the flame can be readily varied to suit conditions in a kiln of any length. Ash and slag cause most of the dificulties incident to the burning of coal. In a. cement kiln, however, the ash, being similar in composition to the raw mix and being deposited uniformly in the mix and clinker, occasions no difficulty as long as it remains constant in quality and quantity. Until 6 years ago almost all cement kilns using pulverized coal employed the bin system. The coal was dried and pulverizeti in a separate plant and delivered into a bin at the kiln. Thus the bin system requires driers, storage-type pulverizers, conveying systems, individual kiln bins, pulverized-coal feeders and primary air fans. The direct-fired system requires only a pulverizer and a blower. Fig. I shows typical plants. The first installations of direct-fired pulverizers were of the impact type but fineness of pulverization was both inadequate and variable. About 1927 a few direct-fired installations employing tube-type pulverizers were made, which were much more satisfactory. As more efficient pulverizers were developed from 1934 on, equipment for direct firing was installed at a large number of plants, until now 196 of about 900 kilns in use in the United States are direct-fired. Most of these replaced antiquated bin systems. Process of Burning Cement Clinkers The process of burning cement clinkers is fundamentally one of heat transfer. In boilers and other heat-exchange apparatus the area of the surface receiving heat from the gases is the best unit for comparing output, This seems to be equally true for kilns. The inside kiln surface is the heat-receiving surface and its area is used as the unit of kiln size in the following comparisons. Heat input is based on British thermal units in the fuel. E. G. Bailey,' in his work on boiler-furnace heat absorption, has used the unit "B.t.u. available." This is the practical calorific power of the fuel, plus the heat in the air used for combustion. In other words, it is the heat available for useful work in the furnace or kiln. The unit of kiln output is barrels per hour. The composition of the raw mix, the percentage of water in the slurry of wet plants and hardness of burning all affect the output. These conditions, however, are hard to evaluate and probably have less effect on the output than irregularities of raw feed and clinker discharge and inexpert control of combustion. Wet vs. Dry Plants The study presented here covers 88 plantsl of which 41 are wet and 47 dry. Of

Jan 1, 1942

By Wm. Reuben Webster

BRASS is an alloy of copper and zinc. The brasses (using this term to denote all useful proportions of the two constituents) are the most valuable and widely employed of all [ ] nonferrous alloys, because of their high resistance to ordinary corrosive agencies and the very wide range of properties that may be imparted to them by variations in the proportions of the constituents and by variations in mechanical treatment and heat-treatment. Fig. I shows the normal physical properties, as determined by standard tensile tests, of the series when in the annealed condition. Fig. 2 shows the effect of varying amounts of cold-working on an almost pure brass containing 70 per cent copper and 30 per cent zinc. Fig. 3 shows the effect of annealing at various temperatures on the same alloy. This effect is somewhat modi- [ ] fied by the degree of cold-working to which a brass has been subjected, as shown by Fig. 4. A fourth test, which is empirical, has been found useful because of its simplicity the hot hammer test. Samples 1/2 in. in diameter and 3/4 in. long are placed in a suitable furnace. These are withdrawn one at a time at successively higher temperatures and are subjected to the blow of a drop hammer weighing 50 lb. with a drop of 4 ft. The percentages of reduction in length of the cylinders are plotted against temperatures and give a comparative measure of plasticity at different temperatures. The results of this test on several

Jan 1, 1942

By R. M. Hardgrove

PULVERIZED coal was first used for firing cement kilns about 45 years ago, with such success that it has continued in general use. Based on cost, pulverized coal is usually the most economical fuel. In some localities natural gas or oil is cheaper, but 85.5 per cent of all cement kilns at present are fired with pulverized coal. The pulverized-coal flame is well suited to kiln conditions. Its soft, luminous nature gives it a high radiating property and the length of the flame can be readily varied to suit conditions in a kiln of any length. Ash and slag cause most of the difficulties incident to the burning of coal. In a cement kiln, however, the ash, being similar in composition to the raw mix and being deposited uniformly in the mix and clinker, occasions no difficulty as long as it remains constant in quality and quantity. Until 6 years ago almost all cement kilns using pulverized coal employed the bin system. The coal was dried and pulverized in a separate plant and delivered into a bin at the kiln. Thus the bin system requires driers, storage-type pulverizers, conveying systems, individual kiln bins, pulverized-coal feeders and primary air fans. The direct-fired system requires only a pulverizer and a blower. Fig. I shows typical plants. The first installations of direct-fired pulverizers were of the impact type but fineness of pulverization was both inadequate and variable. About 1927 a few direct-fired installations employing tube-type pulverizers were made, which were much more satisfactory. As more efficient pulverizers were developed from 1934 on, equipment for direct firing was installed at a large number of plants, until now 196 of about 900 kilns in use in the United States are direct-fired. Most of these replaced antiquated bin systems. PROCESS OF BURNING CEMENT CLINKERS The process of burning cement clinkers is fundamentally one of heat transfer. In boilers and other heat-exchange apparatus the area of the surface receiving heat from the gases is the best unit for comparing output. This seems to be equally true for kilns. The inside kiln surface is the heat-receiving surface and its area is used as the unit of kiln size in the following comparisons. Heat input is based on British thermal units in the fuel. E. G. Bailey,1 in his work on boiler-furnace heat absorption, has used the unit "B.t.u. available." This is the practical calorific power of the fuel, plus the heat in the air used for combustion. In other words, it is the heat available for useful work in the furnace or kiln. The unit of kiln output is barrels per hour. The composition of the raw mix, the percentage of water in the slurry of wet plants and hardness of burning all affect the output. These conditions, however, are hard to evaluate and probably have less effect on the output than irregularities of raw feed and clinker discharge and inexpert control of combustion. WET VS. DRY PLANTS The study presented here covers 88 plants, of which 41 are wet and 47 dry. Of

Jan 1, 1941

By R. M. Hardgrove

PULVERIZED coal was first used for firing cement kilns about 45 years ago, with such success that it has continued in general use. Based on cost, pulverized coal is usually the most economical fuel. In some localities natural gas or oil is cheaper, but 85.5 per cent of all cement kilns at present are fired with pulverized coal. The pulverized-coal flame is well suited to kiln conditions. Its soft, luminous nature gives it a high radiating property and the length of the flame can be readily varied to suit conditions in a kiln of any length. Ash and slag cause most of the difficulties incident to the burning of coal. In a cement kiln, however, the ash, being similar in composition to the raw mix and being deposited uniformly in the mix and clinker, occasions no difficulty as long as it remains constant in quality and quantity. Until 6 years ago almost all cement kilns using pulverized coal employed the bin system. The coal was dried and pulverized in a separate plant and delivered into a bin at the kiln. Thus the bin system requires driers, storage-type pulverizers, conveying systems, individual kiln bins, pulverized-coal feeders and primary air fans. The direct-fired system requires only a pulverizer and a blower. Fig. I shows typical plants. The first installations of direct-fired pulverizers were of the impact type but fineness of pulverization was both inadequate and variable. About 1927 a few direct-fired installations employing tube-type pulverizers were made, which were much more satisfactory. As more efficient pulverizers were developed from 1934 on, equipment for direct firing was installed at a large number of plants, until now 196 of about 900 kilns in use in the United States are direct-fired. Most of these replaced antiquated bin systems. PROCESS OF BURNING CEMENT CLINKERS The process of burning cement clinkers is fundamentally one of heat transfer. In boilers and other heat-exchange apparatus the area of the surface receiving heat from the gases is the best unit for comparing output. This seems to be equally true for kilns. The inside kiln surface is the heat-receiving surface and its area is used as the unit of kiln size in the following comparisons. Heat input is based on British thermal units in the fuel. E. G. Bailey,1 in his work on boiler-furnace heat absorption, has used the unit "B.t.u. available." This is the practical calorific power of the fuel, plus the heat in the air used for combustion. In other words, it is the heat available for useful work in the furnace or kiln. The unit of kiln output is barrels per hour. The composition of the raw mix, the percentage of water in the slurry of wet plants and hardness of burning all affect the output. These conditions, however, are hard to evaluate and probably have less effect on the output than irregularities of raw feed and clinker discharge and inexpert control of combustion. WET VS. DRY PLANTS The study presented here covers 88 plants, of which 41 are wet and 47 dry. Of

Jan 1, 1941

By W. M. Weigel

SALT production in Louisiana and Texas at the present time is entirely from salt domes of the interior and coastal groups. Before and during the Civil War salt was recovered from numerous salines and salt springs by evaporation in open 'kettles. The location of these in nearly every instance was near what is now known to be a salt dome, and the source of the salt in the salines and spring waters was that in the salt core. The tops of many of the shallower domes have been subjected to erosion1. The discovery that the salt occurred as large masses of rock salt in the form of domes was made in May, 1802, at Avery Island, La., by John Marsh Avery, grandson of the original owner, John C. Marsh, who built the old salt works in 18122. The first shaft for mining was sunk on the Avery dome in 1867 by Chouteau and Price. It was 90 ft. deep, about 58 ft. being in solid salt. It was abandoned in 1870. There are three general groups or fields of salt domes; interior Louisiana in northern Louisiana, interior Texas in northeastern Texas, and the coastal domes nearer the Gulf Coast and extending from the Mississippi River to the Rio Grande. This last group contains by far the greatest number of domes. As many of the coastal domes especially are prolific producers of petroleum and a few of sulfur, their geology has been intensively studied and fully covered in the literature. The depth to the top of the salt varies from near the surface, where shallow ground waters have dissolved the salt to just below recent deposits, to several thousand feet, where the depth has been estimated only by geophysical methods. The diameter of the salt core varies from less than ½ mile to over 2 miles. Only domes where the salt is compara-tively near the surface have been developed for commercial salt. Three deeper domes, which will be described later, have recently been developed or are in process of development, as a source of brine for chemical use.

Jan 1, 1935

By Robert H. Leach, C. H. Chatfield

This paper gives a brief summary of the process of manufacture of sterling silver, and some of its more important physical properties, as observed in conlmercial production of rolled sheet and wire. Although papers have been published by Turner and Smith,1 Rose,2 Sperry3 and Jordaq4 there are few technical data available, and unfortunately the time allowed for the preparation of this paper has not been sufficient to make it as comprehensive as the title might indicate. Analysis of Steeling Silver Fine or pure silver is too soft for coinage and the manufacture of articles in which strength and resistance to wear are desired. From the earliest times of which we have record, copper has been the metal generally used to harden silver. Analyses of coins and silver articles from ancient tombs show varying amounts of copper, and old Roman silver objects in the British Museum have approximately the same ana,lysis as our sterling. The first authentic record of the establishment of a standard alloy is during the reign of Henry I1 in England. During the twelfth and thirteenth centuries, the people in the Eastern Provinces of Germany had a reputation for the standard and purity of their silver coinage, and it is said that Henry II employed some of these Easterlings, as they were called, to improve and standardize the English coinage, which had become debased. The peculiar standard adopted is probably accounted for by the system of weights used. A troy pound contains

By John T. Cumberlidge, Frederic M. Chace

Nickel-bearing saprolite developed during the early Tertiary over a northeast trending ultramafic body of Jurassic age near Riddle in southwestern Oregon. The principal nickel mineral is garnierite, but other complex nickel minerals may be present. There are two main ore bodies, an upper (older) one associated with the Klamath peneplain, and a lower (younger) one on the Sherwood peneplain. Saprolite constitutes the bulk of the ore and was probably derived from peridotite and dunite through chemical decomposition by downward percolating meteoric groundwater. Decomposition took place by net loss of MgO, SiO2, and Fe without a change in volume. Faults and joints provided permeable zones which localized saprolite development, and faulting may have helped preserve some ore from loss by erosion. Garnierite-chalcedony boxwork ore was deposited by meteoric groundwater along faults, joints, and at the level of former water tables. Boxwork ore is entirely supergene, the chemical constituents having been derived from higher in the soil profile. The saprolites show evidence of both supergene and residual enrichment in nickel. Red and yellow soil occurs as a capping over saprolite and boxwork, and was derived from them by chemical and mechanical decomposition. The present deposits are probably truncated remnants of a formerly thicker and much more extensive deposit which probably included laterite at the surface. The deposits started to form in the early Tertiary due to deep chemical weathering under sub-tropical to warmtemperature conditions. Early Tertiary ero~ion surfaces of low relief probably contributed to the predominance of chemical weathering over mechanical erosion. Alteration under present climatic conditions favors the formation of soil from saprolite rather than the formation of new saprolite from peridotite.

Jan 1, 1968

By H. Rosenthal, A. L. Jamieson

THE action of mercury on stressed brass to produce cracks was known before Moore, Beckinsale and Mallinson1 showed that actual season cracking did not occur spontaneously but could be induced by ammonia. These investigators studied other substances, including diphenylamine, without finding that anything other than ammonia could cause season cracking. Grimston2 reported season cracking in cartridge cases stored in wooden boxes wetted with dilute sulphuric acid pickling solution. Season cracking associated with sulphur dioxide, water vapor and air has been reported by Johnston,3 although he reported that trimethylamine and pyridine did not cause cracking. Jevons4 has ascribed season cracking of brass in certain instances to trimethylamine, "aldehyde amine," "ketone amine" and pyridine, but no experimental work was done evidently to prove this definitely. Pyridine was investigated by Morris,' who found it to have considerable cracking power. In the present investigation, the object was a qualitative evaluation of a number of representative amines with respect to their ability to cause season cracking. Thus it was desired only that an appreciable vapor pressure of each amine be obtained in order to make the test as severe as possible, without attempting to test equivalent concentrations for comparative purposes. METHODS Specimens Two types of specimen were used: I. Unannealed 70-30 brass cups formed from 0.040-in. thick sheet. Height of cup was 1 3/8 in. and diameter was 1 7/8 inches. 2. First draw pieces of caliber .50 cartridge cases in the unannealed condition (70-30 brass). The cups were representative of a thin wall and thin base specimen, whereas the draw pieces have a thick base (1/4 in.) and a thick wall (approximately 3/32 in.). Both types of specimens contained high residual stress and cracked in less than one minute in a solution of I per cent mercurous nitrate and I per cent nitric acid provided that this was preceded by a 30-sec. pickle in 40 per cent nitric acid. Specimens were prepared as follows: (I) degreased in trichlorethylene, (2) rinsed in H20, (3) pickled 5 min. in 10 per cent by volume H2SO4 (1.84 sp. gr.), (4) rinsed in H2O, and (5) dried. Amines Tested In selecting the amines, representatives of the three series of amines and one series of substituted amines were chosen. The aliphatic series was represented by the methyl and ethyl primary, secondary and tertiary amines. These are the simplest aliphatic amines. For the aromatic series, the phenyl primary, secondary and tertiary amines were selected as being the simplest. The heterocyclic series was represented by pyridine, which is a simple heterocyclic base (tertiary amine).

Jan 1, 1944

By M. Cohen, C. Wagner, J. E. Reynolds

If the total volume of a diffusion couple changes during the diffusion, the measurement of distance becomes ambiguous. Use of distance parameters as suggested by Hartley and Crank is discussed. For small concentration differences, the standard form of Fick's second law is retained with conventional length units and the in- terdiffusion coefficient D. It is shown how D can be calculated from experiments involving large concentration differences and analyzed in terms of distance parameters. 'The merits of incremental diffusion couples involving small concentration differences are emphasized. THE conventional form of Fick's second law for one-dimensional diffusion of component B in a binary solution of A and B is where c, is the concentration of component B; x, the distance; t, the time; and D, the interdiffusion coefficient which may depend on ca. Hartley and Crank' have pointed out that Eq. 1 applies only if the total volume of the diffusion couple does not change during the diffusion process; otherwise, the definition of x becomes ambiguous. No change in total volume takes place if the specific volume of the solution is a linear function of the weight fraction Wb, or if the molar volume is a linear function of the mol fraction N. In some alloys, however, these relationships do not hold, and then it is necessary to introduce a modified measure of distance, 4 in order to retain the general form of Eq. 1. The application of Hartley and Crank's suggestions to diffusion in alloys has been discussed by Wagner.' Relation Between Measure of Distance and Units of Concentration The definition of [ depends on the choice of units for the concentration c,, as follows: 1—If the concentration ca is measured as the weight fraction W, (or weight percent), [ = 5, has to be defined so that equal increments of contain equal increments of mass m of the solution, e.g., dm = pSdx = Sdw [2] where p is the local density of the solution, and S is the cross-sectional area in sq cm which is taken to be constant in this problem of one-dimensional diffusion." * da Silva and Mehla have demonstrated the constancy of the cross-sectional area in the usual type of diffusion couple. However, experiments involving diffusion into thin wires4, 5 may exhibit changes in cross-sectional area, and therefore are excluded from the present treatment. Thus and the unit of is gram per sq cm instead of cm. 2—If the concentration c, is the mol fraction N, must be defined so that equal increments of contain equal numbers of mols of solution, e.g., dn= (S/V)dx= Sd [41 where V is the local molar volume of the solution. Thus dt, = dx/V [51 and the unit of is mols per sq cm. 3—If, as may be advisable in the case of interstitial solutions, the concentration C is measured in terms of the molar ratio of components B and A (c,, = Y, = nH/nA, where n and nl are numbers of mols of B and A), = Y has to be defined so that equal increments of contain equal numbers of mols of A, e.g., dnA= (NAS/V)dx = Sdf [6]

Jan 1, 1954

By E. F. Kingsbury

One of the well-known and important uses of the noble or precious metals has been for electrical contacts. In fact, the elements of this group, comprising gold, silver and the six platinum metals, have been called "noble" because of their ability to resist heat and corrosion, properties which were early found to be of importance in good contacts. Of these, platinum and its iridium alloys, palladium, and silver, have been extensively used. In recent years the electrical industry has been responsible for about one-eighth of the total consiimption of the platinum metals in the United States. Information is not available as to what part of this one-eighth has been used for contacts but it is certainly an important one. Substitutes for Platinum During the past 20 years a considerable number of contact alloys have been proposed in the patent literature largely with the aim of more or less replacing platinum by gold or silver, and some of these alloys are finding increasingly widespread application as the reliability of their performance becomes established. From even the partial data at hand it appears that this substitution by the less precious metals has replaced at least one-half of the amount of platinum that the entire electrical industry would otherwise be consuming at the present time. While the subject is of considerable interest to the metallurgist it is even more so to the electrical engineer and it is surprising that the literature records no systematic and comprehensive investigation along these lines. Practically all the scattered work on noble metal contacts has centered around platinum as a standard and has had two more or less distinct aims. One of these has been the replacement of platinum by cheaper matcrials, and the other, the dcveloprnent of materials of superior electrical performance. The merit of a contact metal has been assumed to be dependent on its infusibility, and since thc more precious metals have the higher melting points there has naturally been an association of the two qualities in the sense that the more precious were