Search Documents

By R. G. Vardiman, M. R. Achter

Observations of dislocation structure in niobium are presented using two techniques. Triangular pits developed by electroetching are confined to orientations in the stereographic triangle between the (111) pole and planes of the (1ll) zone and require the presence of carbon. Some unusual electroetching phenomena at other orientations are noted. A chemical etch of dislocations decorated by the addition of carbon to 50 ppm reveals the complete dislocation line structure in a surface layer up to 30 p deep, with a resolution of less than 1 p. This effect is independent of surface orientation. The structure of subboundary nets may be resolved for misorientations up to about 1'. Dislocation structures found in strain anneal grown crystals, such as helices, prismatic loops, and high-density areas, are observed. The measurement of dislocation density is discussed and values obtained in different ways are compared. IN the course of some work on the response of refractory metals to thermal-mechanical treatments, it was desired to examine the defect structure of relatively low dislocation density crystals of niobium in bulk form. Surface and bulk methods for the observation of dislocations have been reviewed by ~melinckx,' and include etch pitting, decoration, and various X-ray techniques. The dislocation line structure has been developed by decoration in a few metals, although observations were limited to certain orientations, or by the coarseness and nonselectivity of the precipitate. The most commonly used technique is etch pitting. In niobium, etch pits have been developed chemically'0," in material of high impurity content and electrolyti-cally'' in relatively pure material. In this paper, etch pits developed electrolytically, and the dislocation line structure of a surface layer developed by decoration and chemical etching, are examined, and observations are presented from both techniques. EXPERIMENTAL METHODS Our starting material was electron-beam-melted niobium, swaged to 4 or -in.-diam rod. Chemical analysis is given in Table I. Single crystals were grown by a strain anneal technique using 1 to 2.5 pct of strain and growth temperatures of 1700" to 2300"~.'~ Some crystals grown by zone melting were also examined. The desired surface orientation was exposed either by spark machining or by sectioning with a cut-off wheel and prepared for etching by electro-polishing.

Jan 1, 1969

By L. J. Health

Synthetic rock with predictable porosity and permeability has been Prepared from mixtures of sand, cement and water. Three series of mixes were investigated primarily for the relation between porosity and permeability for certain grain sizes and proportions. Synthetic rock prepared of 65 per cent large grains, 27 per cent small grains and 8 per cent Portland cement, gave measurable results ranging in porosity from 22.5 to 40 per cent and in permeability from 0.1 darcies to 6 darcies. This variation in porosity and permeability was caused by varying the amount of blending water. Drainage-cycle relative permeability characteristics of the synthetic rock were similar to those of natural reservoir rock. INTRODUCTION The fundamental behavior characteristics of fluids flowing through porous media have been described in the literature. Practical application of these flow characteristics to field conditions is too complicated except where assumptions are overly simplified. The use of dimensionally scaled models to simulate oil reservoirs has been described in the literature. 1-3 These and other papers have presented the theoretical and experimental justification for model design. Others have presented elements of model construction and their operation. In most investigations the porous media have consisted of either u ncon soli da ted sand, glass beads, broken glass or plastic-impregnated granular substances—materials in which the flow behavior is not identical to that in natural reservoir rock. The relative permeability curves for unconsoli-dated sands differ from those for consolidated sandstone. The effect of saturation history on relative permeability measurements is discussed by Geffen, et a1.4 Wyga15 has shown quite conclusively that a process of artificial cementation can be used to render un consolidated packs into synthetic sandstones having properties similar to those of natural rock. Many theoretical and experimental studies have been made in attempts to determine the structure and properties of unconsolidated sand, the most notable being by Naar and Wygal.6 Others have theorized and experimented with the fundamental characteristics of reservoir rocks. This study was conducted to determine if some general relationship could be established between the size of sand grains and the porosity and permeability in consolidated binary packs. This paper presents the results obtained by changing some of the factors which affect the porosity and permeability of synthetically prepared sandstone. In addition, drainage relative permeability curves are presented. EXPERIMENTAL PROCEDURE Mixtures of Portland cement with water and aggregate generally are designed to have certain characteristics, but essentially all are planned to be impervious to water or other liquids. Synthetic sandstone simulating oil reservoir rock, however, must be designed to have a given permeability (sometimes several darcies), a porosity which is primarily the effective porosity but quantitatively similar to natural rock, and other characteristics comparable to reservoir rock, such as wettability, pore geometry, tortuosity, etc. Unconsolidated ternary mixtures of spheres gave both a theoretically computed and an experimentally observed minimum porosity of about 25 per cent.7 By using a particle-distribution system, one-size particle packs had reproducible porosities in the reproducible range of 35 to 37 per cent.6 For model reservoir studies of the prototype system, a synthetic rock having a porosity of 25 per cent or less and a permeability of 2 darcies was required. The rock had to be uniform and competent enough to handle. Synthetic sandstone cores were prepared utilizing the technique developed by Wygal.5 Some slight variations in the procedure were incorporated. The sand was sieved through U. S. Standard sieves. A 18-20 sand denotes that the sand passed the Number

Jan 1, 1966

By A. W. Schlechten, R. P. Abendroth

Jan 1, 1960

By C. C. Harris, A. Jowett, S. K. Ghosh

An equation derived from first-order kinetics and accounting for return from froth to pulp has correlated continuous flotation data. The concentration of floatable material in the pulp can be altered either by changing the feed concentration or the feed rate. The latter does not affect the flotation rate constant, the froth to pulp return constant, and the concentration of non-floatable material in both the pulp and concentrate. Both the return constant and the concentration of non-floatable material in the pulp are directly proportional to the feed concentration, while the concentration of non-floatable material in the concentrate is related to the feed concentration. The investigation of the froth flotation process by continuous test methods, previously used by Brown and smith,1 Jowett and Safvi2 and Jowett and West,3 is being continued. Recent tests, primarily concerned with flotation cell design, have yielded kinetic data suitable for testing an equation proposed by Arbiter and Harris4 which postulates that a flotation process is defined by two rate constants: 1) the rate constant for mass transfer from pulp to froth. Previous workers have regarded this as the flotation rate constant. 2) the rate constant for mass transfer from froth to pulp, which has previously been ignored. THEORY Under continuous flow conditions at the steady state in Fig. 1 the equation developed4 is Symbols are defined in Table I. The air-liquid ratio terms4 have been omitted, since they are substantially constant for a given set of conditions. Also, for a system operating at the steady state Vf and V, remain constant and Eq. 1 can be written: Cp/Cc=b'/a,+Qc/a' [2]

Jan 1, 1963

By D. A. Elgillani, M. C. Fuerstenau, J. D. Miller

Adsorption of lead and ferric iron on quartz and alumina is presented as a function of pH. Only the hydrolyzed species of these metal ions, FeOH++ and PbOH+, adsorb significantly on each of these minerals. Zeta potentials of quartz were measured as a function of pH in the presence of various additions of aluminum, lead, and magnesium salts. Sign reversal occurs at the pH values where significant concentrations of hydroxy complexes are formed. Models of adsorption are presented in the absence and presence of collector. The mechanism of adsorption of metal and collector species in the activation of nonmetallic minerals is still the center of considerable discussion in spite of the extensive study given this system. Until recently, the view was widely held that hydrated metal ions were responsible for this phenomenon. This fact is surprising, since it had been shown that the pH range in which flotation is effected corresponds to that in which metal ion hydrolysis occurs.' Additional support of this concept was pro vided by the work of Wolstenholme and Schulman in another system.' Later work has shown that hydroxy complexes of metal ions are the active species. These studies have also indicated that basic aqueous complexes of metal-collector may be necessary for flotation.3-7 Depending on the molecular weight of the collector, formation of these complexes may occur before or after precipitation of the metal-collector salt has occurred. Ion pair formation can occur when low molecular weight collectors are involved because relatively high concentrations of metal hydroxy complex and collector can be present in solution before precipitation occurs. This is not the case when high molecular weight collectors are used. A model of aqueous complex adsorption has been presented6,7 in which it has been assumed that adsorption occurs by the formation of water from adsorbed hydroxyl and hydrogen of the hydroxyl contained in the complex. Other authors8 have suggested that hy-droxy complexes are involved in these systems but that collector adsorption occurs by replacement of the hydroxyl of the adsorbed metal hydroxy complex with a fatty acid anion. All of these investigations have involved mineral surfaces that were negatively charged so that it is not possible to state with certainty whether hydrated metal ions or hydroxy complexes are the active species in this system. Use of a positively charged mineral should be helpful, however, since the hydrated metal ion will be repelled from this surface. On the other hand, if the hydroxy complex adsorbs by splitting out water, surface charge should have no effect because of the free energy decrease that the system will experience when water is formed. In this regard, sapphire is well-suited for study, since its surface is positively charged until approximately pH 9. Electrokinetic studies of quartz in the presence of various metal ions should also be useful in establishing the mechanisms of adsorption in these systems. That is, if the hydroxy complexes adsorb by water formation, drastic changes in the zeta potential should occur in the pH range in which hydrolysis occurs. In this view, adsorption of ions of widely different hydrolysis characteristics on both sapphire and quartz was measured. In addition, zeta potentials of quartz were measured as a function of pH in the presence of various metal ions and compared with flotation responses obtained under similar conditions. Experimental Materials and Techniques Reagent-grade aluminum, ferric and magnesium chlorides, and lead nitrate were used in this investigation. Adjustments in pH were made with reagent-grade HCl or KOH. Conductivity water, made by passing distilled water through an ion exchange column, was used in all of the experiments.

Jan 1, 1971

By H. B. Pulsifer

ONE of the most common basic open-hearth furnace products is a simple carbon steel with a carbon range from 0.05 to 0.15 per cent. The material is widely used for sheets, tubes, bars, wire and the innumerable special objects of secondary fabrication. The properties of the material vary over wide ranges, depending on the more exact composition and details of manufacture or treatment that affect its structure. The present paper is a review of those properties and structures that have been found by studying this steel as used in the cap screw industry. At first glance this might be thought a narrow application of the steel, but, since the industry uses the material in the cold-worked, annealed and heat-treated conditions, the title of the paper may be excused for its comprehensiveness. Yet, in studying the wide ranges of properties and structures that preclude a more specific title, there can be no suggestion of completeness or finality. Even a summary of a few years' work is no more than a preliminary survey of a field that will be fertile in scientific data and industrial products for many years to come. An outline of the structures will be given first, then a list of the previous contributions that are at hand and finally some details of the work and related problems, especially concerning this low-carbon steel in the surface-hardened condition.

Jan 1, 1931

By C. O. Lee, Z. W. Bartlett, R. H. Feierabend

The Grand Isle sulfur mine is located in the Gulf of Mexico, approximately seven miles off the coast of Grand Isle, Jefferson Parish, La. The deposit is on acreage covered by oil, gas, and mineral leases originally issued in favor of Humble Oil & Refining Co. by the State of Louisiana which were continued, maintained, and redesignated by the U.S. Department of the Interior after passage of the Outer Continental Shelf Lands Act. The sulfur deposit was discovered in 1949 when Humble Oil & Refining Co. penetrated more than 200 ft of sulfur-bearing limestone in a zone between 1813 and 2075 ft below sea level. In 1954, Humble drilled ten more sulfur prospect holes, eight of which encountered sulfur ore. On September 19, 1956, Freeport Sulphur Co. acquired from Humble Oil & Refining Co, the sulfur rights underlying the tracts, and the actual design of the installation began the same month. The first structural contract was awarded in December 1957 and offshore erection began in June 1958. The initial phase of construction has been completed and production by the Frasch process commenced in April 1960. The estimated total cost of the project is $30 million, of which $8 million is the extra cost incurred by the necessity of offshore operations. More than $22 million was expended before production was started. GEOLOGY OF DEPOSIT Grand Isle is the third largest sulfur deposit in the U.S. The orebody embraces several hundred acres, but its outer limits are yet to be defined to the northeast, east, and south. Most Gulf Coast sulfur deposits occur in a caprock mantle of calcite (referred to as limestone), anhydrite, and occasionally gypsum, which covers the apex of an intrusive mass of salt. Commercial quantities of sulfur are usually confined to the calcite or limestone member. Most often such limestone is completely enclosed by dense anhydrite below and impervious sediments above, which effectively form a closed reservoir. The depth of the Grand Isle orebody ranges from 1800 ft to 2500 ft below sea level. Within the present boundary, the sulfur-bearing limestone varies in thickness from 220 ft to 425 ft, while the sulfur content varies an average of about 15 pct in the leanest hole to an average of about 30 pct in the richest. Rock containing less than 5 pct sulfur is not classed as ore, and holes assaying less than 20,-000 long tons per acre of sulfur in place are not considered commercial offshore. The sulfur enrich-

Jan 1, 1961

By K. E. Gray, M. S. Seth

In Part I of this work,1 equations of elasticity were formulated for transversely isotropic, axisymmetric, homogeneous, porous media exhibiting pore fluid pressure. Equations of elasticity and the thermal analogy method were used to determine transient horizontal, tangential, and vertical stresses and radial displacement in a semi-infinite cylindrical region when either a constant rate of pressure or a constant rate of flow is maintained at the wellbore. In this paper, the approach presented earlier is extended to finite reservoirs for the cases of (1) steady-state flow, (2) constant pressures at the well bore and outer boundary and (3) constant pressure at the wellbore and no flow at the outer boundary. Results of this work show that radial and tangential stress gradients are high near the wellbore but diminish rapidt; away from the well; the vertical stress gradient behaves in the same way but is less severe. Radial stresses are compressive or neutral, whereas tangential and vertical stresses may be tensile, neutral or com-pressive, depending upon the boundary conditions, the physical Properties of the system and the radial distance involved (vertical stresses are always compressive in an unbounded system1. For constant boundary pressures, both radial and tangential stresses increase with time whereas they both decrease for a closed outer boundary and constant pressure at the wellbore. The vertical stress decreases with time for both systems. For steady-state systems, radial displacement may be positive or negative, depending upon the dimensions of the system, the pressure differential and the porosity. Radial displacement may be positive or negative for a closed outer boundary but is positive for constant pressures at both boundaries. INTRODUCTION The importance, utility and complexity of a realistic appraisal of the stress state at and local to a wellbore were indicated in Part I. In this paper the analytical approach presented earlier is extended to finite, cylindrical reservoir geometry for the cases of (1) steady-state flow, (2) constant pressures at wellbore and outer boundary and (3) constant pressure at the wellbore and no flow at the outer boundary. Other than the outer boundary of the reservoir being finite, the physical system and assumptions pertinent thereto are the same as before. The reader may wish to review the mathematical development through Eq. 49 of Part I before proceeding here. SOLUTION FOR GENERAL BOUNDARY CONDITIONS THERMAL STRESSES AND DISPLACEMENTS Since normal stresses do not exist at the free boundaries of a system subjected to thermal stresses, the boundary conditions are

Jan 1, 1969

By A. W. Ruff

The seismic wave produced by an explosive is very important in blasting. A true understanding of the wave is only important when considering possible structural damage to buildings located near the blast, but it is also of primary importance when considering rock fragmentation. Because of the importance of the seismic wave to fragmentation, a finda-mental study of the seismic wave and its effect was made at the Cananea Consolidated Copper Co.'s mine at Cananea, Sonora, Mexico. Strain gages were used to measure the strain in the rock when nearby explosive charges were detonated. The variance in the circuit voltage caused by changes in the resistance of the strain gage was measured with an oscilloscope and recorded with a Polaroid camera. CONFINED DRILLHOLE CHARGES To record the seismic wave from a confined drillhole explosive charge, a gage was cemented to the bottom of a 4-in diam drillhole. The horizontal gage hole and nine horizontal charge holes were drilled perpendicular to the center line of the 2-39 drift and 4 ft above the floor. The gage hole was 29 in. deep, and the charge holes were drilled so that each bottomed 1 in. deeper than the gage hole. The gage was installed with its axis horizontal and parallel to the 2-39 drift. The charge holes had the following horizontal distances from the gage: hole 3, 3 ft; hole 4, 4 ft; hole 5, 5 ft; hole 9, 9 ft; hole 10, 10 ft; hole 14, 14 ft; and hole 15, 15 ft. Figs. 1 and 2 show the relationships of the gage and the charge holes. Charges of 80 pct special gelatin, which weighed 50, 100, and 150 g were exploded in the charge holes and the seismic waves were recorded. All charges were stemmed with 200 g of mud and detonated with an electric blasting cap. Fig. 3 shows the recorded seismic waves. The reflected components of the waves were too weak to be objectional on these records. Table I shows the data taken from the wave forms. The approximate average velocity of a wave with a 9-ft travel distance was 12,900 fps. Since different charge weights were used, it was necessary to scale the data. The scaled maximum compress ion-strain data and the scaled maximum tens ion-strain data are shown in Figs. 4 and 5, respectively. Figs. 6 and 7 show the strain-distance data from Figs. 4 and 5 converted to a 1-lb charge. The results showed that the wave consisted of an initial compression pulse followed by a tension pulse. The amplitude of the tension pulse approached the amplitude of the compression pulse as the distance between the gage and the shot increased. The decay rate of the seismic wave is very important in the evaluation of the blasting characteristics of a rock. When high-amplitude stresses are produced, as in rock fragmentation, the rate of decay is much more rapid than when small amplitude stresses are produced. In underground mine blasting, the burdens are usually not greater than 6 ft and the decay is very rapid. The rapid seismic-wave decay rate in the fragmentation range means that in practice, if the minimum weight of powder is used to break a specified burden, only a very

Jan 1, 1961

The pellet plant, built by Dravo Corp, in Groveland, Mich., for the Hanna Mining Co., is now in full operation. Although using jasper, a type of iron ore with low iron content (approximately 28% Fe), the plant has a rated capacity of 1,250,000 tans of pellets per year. In its four years of existence, the nearby concentrating plant has seen its capacity increase from 700,000 tons to 1,500,000 tons a year as part of a major expansion program at Groveland. Utilizing the Dravo-Lurgi continuous grate process, the pellet plant produces %a-in. pellets of more than 60% iron content. The fully-hooded pelletizing grate, largest in the U.S., is 9 ft. 10% in. wide and 223 ft. 1% in. tong over 34 windboxes, with an effective hearth area of 2195 sq. ft. Drying, firing, and cooling functions are all carried out on this single piece of equipment.

Jan 4, 1964

By H. S. Martin

The Phosphate Recovery Corporation operates three flotation plants, Nos. 1 and 2 concentrators about three miles northeast of Mulberry, Florida, and No. 3 plant at Wales, Tennessee. These plants represent the first commercial phosphate flotation operation and are also believed to be the largest nonmetallic flotation operation in the world at the present time. The details of this paper will be confined to plant No. 2, this being the newest and largest concentrator in Florida, and the flow sheet being practically the same as at plant No. 1. The No. 3 plant has been operated but a short time and has been shut down since December, 1932, on account of the decrease in phosphate rock production. The phosphate washers usually are located centrally on a known deposit so that about two hundred acres of ground can be mined economically to each washer location. The washers are moved to new areas when the distance becomes too great for economical pumping. The flotation plants are built either adjacent to a washer, so that current debris may be utilized, or on the site of a former washer where there is sufficient accumulated debris available for mining, and the flotation plants must also be moved from time to time. Most of the water used in the Florida flotation plants is recovered after passing through a circulating system where most of the fine suspended matter is settled out, but some make-up water is obtained from deep wells near the plant. Power is obtained from the Tampa Electric Co. through the distribution facilities of the International Agricultural Corporation. Flotation concentrate is hauled from the plant by trolley over the International Agricultural Corporation's trolley system, to the drying plant at Prairie, one mile northwest of Mulberry. Ore Treated In the pebble phosphate district of Florida, the phosphate mineral, or collophane, is usually found in horizontal beds of varying thickness

Jan 1, 1935

By H. Conrad

The strain hardening associated with the creep of magnesium single crystals at room temperatu.Je was investigated by shear tests in which the direction of stressing was reversed a number of times after creep in a <100> direction. The strain hardening was strongly anisotropic; the largest amount occurring in the direction of flow and the least 180 deg to this. The time law for creep changed from a parabolic type to logarithmic for the first and subsequent reversals of stress. For a given stress the creep strain decreased significantly for the first and second reversals and then only slightly for subsequent reversals. The logarithmic creep constant a changed in a similar manner. A linear relationship was observed between the creep strain for a given reversal and the stress. The slope for the third reversal yielded a strain hardening coefficient 12 to 16 times greater than that observed for unidirectional flow. Al-though no recovery was observed upon resting at room temperature, the hardening resulting from stress reversals could be completely removed by heating to 450" C. PREVIOUS work1.&apos; indicated that the creep rate of magnesium single crystals tested in the temperature range of 78" to 364°K decreased with time. This was attributed to an increase in internal stress resulting from an accumulation of dislocations at internal obstacles. The object of the present investigation was to further evaluate the nature of this hardening by conducting tests in which the direction of stressing is changed after previous creep in shear in a given slip direction. Previous to 1950 three investigations indicated that a Bauschinger effect3 occurred for single crystals as well as polycrystals brass in tension compression,

Jan 1, 1960

By E. J. Dulis, A. Kasak, R. C. Westgren

The potential of uirought tungsten- and tantaluw-rich alloys of the W-Ta-Mo-Cb system was investigated for high-strength structural applications above 2500° F. Appreciable strengthening of tung-sten and tantalum—essentially attributable to solid-solzction effects—was obtained with binary, ternary, and quaternary alloys. Tensile strengths as high as 67,000 psi were achieved at 3000 OF. ThE quest for wrought structural materials which possess good strength properties at temperatures above 2000°F has led to a considerable research effort during the past decade. In addition to exploring the potential of various high-melting-point refractory metals (such as molybdenum, columbium, tantalum, and tungsten) for very high-temperature structural applications, alloy-development programs have been undertaken to achieve greater strengths than could be achieved with unalloyed refractory metals. The methods of strengthening refractory metal alloys have included both solid-solution and dispersion strengthening. General relationships among the relevant properties (melting point, recrystallization temperature, and high-temperature strength) of refractory metals indicate that the highest strengths at temperatures of 2500°F or higher would be obtained with tungsten-or tantalum-base alloys. Therefore, the present investigation was undertaken to determine the high-temperature strength potential of solid-solution strengthened alloys based on the binary system W-Ta; to effect further strengthening, minor additions of molybdenum and columbium (at the 6 and 12 pct levels) were made. The portion of the W-Ta-Mo-Cb quaternary alloy system of interest is shown schematically in Fig. 1. The component metals—W, Ta, Mo, and Cb—have a bcc structure at all temperatures, and their binary systems are mutually completely soluble.&apos; Complete solid solubility in the W-Ta-Mo and W-Ta-Cb alloy systems has been demonstrated,&apos; and, therefore, it was expected that the quarternary alloys of the system would also exhibit complete solid solubility at all temperatures. In the virtual absence of contamination by interstitial elements, all the alloys would be truly solid-solution strengthened. Twenty specific compositions of this investigation included binary, ternary, and quaternary alloys of the W-Ta-Mo-Cb system as well as unalloyed tungsten and tantalum. The compositions are shown in Table I. EXPERIMENTAL PROCEDURE Consumable-electrode vacuum-arc melting with ac power was used to produce small laboratory-sized, cylindrically shaped ingots (1-1/4 in. in diameter and 2 to 3-1/2 in. long) of the twenty compositions. A furnace was specially constructed to melt as many as four electrode rods simultaneously into molds lined with tungsten or tantalum sheet. High-purity rods of tungsten, tantalum, molybdenum, and columbium were used for consumable electrodes; the diameter of each rod was determined by the desired weight percentage of the component metal in a given alloy. The details of the construction and operation of the melting furnace will be discussed in another p~blication.

Jan 1, 1964

By L. H. DeWald

During the examination of various commercial brands of copper wire bars, which had exhibited different degrees of adaptability for being drawn into fine gages of wire by the present-day high speed machine, it was found that each brand had a more or less characteristic crystal macrostructure. The extremes of these macrostructures are similar FIG. 1.-EFFECT OF METAL TEMPERATURE IN CASTING ON CRYSTAL MACROSTRUCTURE OF BAR. Reading from left to right, metal temperatures were 1166" C., 1149" C., 1132" C.. 1121" C., 1093" C. to the maximum variation shown in the photomacrographs reproduced in Fig. 1. As the various brands did not differ materially in chemical composition, it was concluded that the differences in structure were the result of variations in casting technique.

Jan 1, 1931

By E. H. T. Whitten

Fundamental principles of trend surface analysis are briefly reviewed. Recent analyses of several granite masses illustrate the method of estimating the quantitative regional composition and also variation trends. Mineralogi-cal, bulk chemical, and other quantitative variates can be employed. Such results should improve gravimetric surveys (etc.) relying on correction terms based upon estimated rock composition. For the first time realistic estimates of the mean composition of rock bodies can be made with the aid of trend components. Deviation maps hold promise for delimitation of disseminated mineralized areas. Deviations comprise residual "anomalies" after removal of trend components. In petrogenetic work such deviations have been shown to reflect local influences (e.g., contamination of magma by assimilation of xenoliths or country rocks of the envelope). Similarly, mineralization should be reflected as deviations standing out from background trends. Actual examples are given. Present results largely involved projection of data onto a horizontal plane, but if sufficient data are available use of three spatial coordinates increases accuracy for prediction in "unexposed" areas. Regression analysis shows that statistical correlations between variates for regionally distributed specimens are often strong (particularly with percentage data). Hence, in preliminary surveys more easily determined variates may sometimes be employed to gain first estimates of the distribution of components more economically significant. The sampling plan is of paramount importance. Unless a suitable sampling plan is devised and adhered to rigorously during collection of the samples, all subsequent analysis is liable to strong bias and to yield spurious estimates of the truth. For a wide variety of purposes it is becoming necessary to assess the quantitative composition and variability of rock masses and mineralized zones of various types. In petrology and petrography this is something of a break with tradition, because virtually all descriptions heretofore have been qualitative. Although vast amounts of qualitative data have been compiled, little is known about the quantitative behavior of rock components. However, if variability of rocks could be understood and expressed with sufficient accuracy, there would be considerable advantage to both economic and petrogenetic problems. For example, if, on the basis of a limited series of observations, the three-dimensional geometry of a disseminated orebody (or ore-bearing formation) could be predicted accurately, it would be possible to extrapolate with confidence the structure into unexposed areas. The following example based upon the geometry of an igneous cone sheet illustrates the point. The significant rock-unit gives outcrops at a number of points on the exposed surface ABCD (Fig. 1A). Study of n exposures may enable a geologist to predict that the rock-unit is circular in form and thus indicate where the unit can be expected in unexposed terrain. Such observations are made at sites with u, v coordinates, but, if subsurface information is available at sites with uvw coordinates, it will eventually become possible to predict accurately the three-dimensional form of the rock mass. Geologic rock masses or mineral deposits are not generally as regular and symmetrical in geometric form as the body illustrated in Fig. 1A. However, even where the broad limits of a major rock mass are known, a more acute problem arises in attempting to obtain detailed quantitative estimates of its internal variability; it is difficult to predict the variability of a mass from a limited number of observa-

Jan 1, 1961

By J. P. Neumann, L. Raymond

At temperatures near 1000°C, only the (112) (111) slip systems are operatire in tungsten. Therefore, the substructure introduced into the billet upon rleforming a single crystal by rolling at 1000 "C can be controlled by proper selection 01. processing ral&apos;iubles. Using a reduction of 10 pct pel- pass, the (001)[110] and the (110)[001] crystals will deform by duplex slip rip to a 50 pet reduction in thickuess. These rolled single-crystal sheels are characlerized by anisotropic hardening, retention of ductility with warm working, lattice bending which is related to the conlacl (angle, and macroscopic dimensional changecs in the length bid not the width of the billet. When several slip systems become operative, a greater degree of work hardening is itztvoducetl into the crystal. This rolling- condition is characlerized by isotropic hardening, loss of ductilily with warm working, complex lattice distortions, and macro-scopic dimensional changes in both the length rind Width of the billel. IN tungsten, the {1 10}(111) slip systems are operative below room temperature,&apos; while above 700°C only the {112{ (111) slip systems are observed.2,3 In the transition region, i.e., room temperature. both systems appear. It is the purpose of this investigation to show that tungsten single crystals deformed by rolling at a temperature where only one slip system is operative generate dislocation substructure which depends on the crystal orientation. For a specific crystal orientation. the resulting dislocation substructure can be further influenced by modifying the rolling procedure. Crystals oriented for multiple slip display less substructural sensi- tivity to modifications in processing techniques than do single crystals oriented for duplex slip. Under simple slip modes of deformation, very little work hardening is introduced into a rolled single-crystal sheet. Mechanical properties such as room-temperature strength. ductility, and hardness are used to confirm the existence of the different work-hardened conditions generated within the crystal by modified warm-rolling techniques. EXPERIMENTAL PROCEDURE Material. Single-crystal billets of four different crystal orientations. grown by the Arc-Verneuil technique. were ground to a size of 0.25 by 0.375 by 3 in. In terms of their rolling plane and rolling direction, the billets had the following orientations: (1101 [001 ] (110) [110] (001) [110] (001) [100] The actual orientation of all crystals was within 5 deg of the ideal orientations. The typical impurity content of the crystals is given in Table I. Polishing and Etching. Polishing was done elec-trolytically in a 20 g per liter aqueous solution of NaOH at approximately 10 v. It was established by the Laue back-reflection X-ray technique that the surface damage due to grinding and cutting operations with a diamond wheel did not exceed 0.001 in. Therefore after each cutting or grinding operation at least 0.002 in. was removed electrolytically from the surface in order to eliminate surface effects. By lowering the voltage to 3 v, subgrain boundaries and individual dislocations are identified in agreement with Berlec 4 where the etch-pit traces on a cubic plane form a square. The etching time was about 5 sec at room temperature. Rolling. Rolling was carried out on a Loma 2-high mill (Model 600). The peripheral velocity of the 6-in.-diameter rolls was 500 in. per min, with the surface temperature of the rolls about 400° to 450° C The billets were heated before each pass for 30 min in argon to 1000 C. Oxidation of the crystals during rolling in air resulted in a thin layer of greenish-yellow WO 3 This oxide was removed after each pass by immersing the crystals for a few minutes in a boiling NaOH solution. Prior to the initial rolling pass, a surface layer of 0.001 in. was removed by polishing. The crystals were then annealed in vacuum (10-4 torr) at 2400 C for 30 min. All crystals were rolled in the same direction; i.e., the same end was always introduced into the rolls. The rolling program was conducted in

Jan 1, 1965

By C. G. Cheriton

The Bathurst mining district is located near the town of Bathurst on the north shore of the province of New Brunswick in eastern Canada. This region is the northeasterly extension of the Appalachian mountain system. The area is heavily forested and covered with a fairly uniform layer of glacial gravels and boulder clay. The relief is low, increasing to a few hundred feet in the north west and several hundred feet in the extreme southwest. Thus, rock outcrops are scarce and occur mostly along streams and ridges. These factors made conventional prospecting difficult and resulted in the district becoming an excellent place for the application of regional geological studies, air photo techniques, airborne and gound geophysical methods and soil sampling. Late in 1952, The Brunswick Mining and Smelting Company discovered a very large base metal sulphide body presently known as their No. 6 orebody. Early in 1953, another and even larger sulphide body was discovered and is known as the No. 12 ore body. Mining exploration was very active thoughout 1953 and in 1954, The American Metal Company discovered the orebodies which have been developed into The Heath Steele &apos;Mines. The location of these deposits is shown on figure one. In the latter part of 1954, The Anaconda Company became interested in the district and decided to make a geological study of this new and promising base rrietal area. The following paper presents the story of the application of modern geological and geophysical techniques, leading to the discovery of a large sul-nhidp liodv. The Bathurst district is generally underlain by the Tetagouche group of Middle Ordovician rocks.

Jan 1, 1961

By Waldemar Lindgren

THE following pages present data accepted by many geochemists and geologists regarding the succession of minerals and the temperatures of formation in ore deposits affiliated with igneous rocks. They also present the individual views of the author on the composition of the solutions that were active and on the mode of deposition. He does not regard these views as speculations or hypotheses but as forming a well motivated and consistent theory. It is not certain, however, that all investigators will subscribe to them.

Jan 1, 1936

By Gorr W. W., Wyche E. H, R. Smith

The combination of high strength and corrosion resistance of cold-worked 18 Cr, 8 Ni steel has been advantageously utilized for some time, particularly in aircraft and rail car structures. There are, however, certain limitations on the use of such materials because the high strengths can be obtained only by cold-working, limiting the available products to sheets, strip, wire and tubes. The authors sought to overcome these limitations by resorting to precipitation-hardening, which has been used so successfully in nonferrous metallurgy but only to a limited extent in iron-base alloys. Accomplishment of this objective not only overcame the limitations, but also effected certain improvements in mechanical and other properties. This paper is an account of the development by Carnegie-Illinois Steel Corporation of a precipitation-hardening 18-8 stainless steel (called Stainless W‡ and tentatively identified as type 322). A description is given of its composition and metallurgical characteristics, heat-treatment, physical and mechanical properties and corrosion resistance. Development of the New Steel For a considerable length of time the authors were unable to determine the mechanism of the precipitation-hardening process that had been noted by Ffield18,19 in 18-8 Ti or 18-8 Cb after cold-working and reheating to moderately elevated temperatures. All known variables were exhaustively studied, but with little success. However, results began to indicate that chemical composition was the most important variable, particularly the ratio of austenite-forming to ferrite-forming elements. The investigators then focused their attention upon the composition, and, in particular, upon the element titanium and its mode of alloying in the presence of other elements. A heat was obtained that could not be brought to the softness level of annealed 18-8. The response to cold-straining and aging* was very marked by previous standards, and, more important, cold-straining was found to be entirely unnecessary to produce the precipitation-hardening effect. The chemical composition of this heat was: C, 0.06 per cent; Mn, 0.54; P, 0.016; S, 0.016; Si, 0.58; Ni, 7.28; Cr, 17.60; Ti, 0.90; Al, 0.17. For some time the development work, particularly on composition, was carried

Jan 1, 1947

By Gorr W. W., R. Smith, Wyche E. H

The combination of high strength and corrosion resistance of cold-worked 18 Cr, 8 Ni steel has been advantageously utilized for some time, particularly in aircraft and rail car structures. There are, however, certain limitations on the use of such materials because the high strengths can be obtained only by cold-working, limiting the available products to sheets, strip, wire and tubes. The authors sought to overcome these limitations by resorting to precipitation-hardening, which has been used so successfully in nonferrous metallurgy but only to a limited extent in iron-base alloys. Accomplishment of this objective not only overcame the limitations, but also effected certain improvements in mechanical and other properties. This paper is an account of the development by Carnegie-Illinois Steel Corporation of a precipitation-hardening 18-8 stainless steel (called Stainless W‡ and tentatively identified as type 322). A description is given of its composition and metallurgical characteristics, heat-treatment, physical and mechanical properties and corrosion resistance. Development of the New Steel For a considerable length of time the authors were unable to determine the mechanism of the precipitation-hardening process that had been noted by Ffield18,19 in 18-8 Ti or 18-8 Cb after cold-working and reheating to moderately elevated temperatures. All known variables were exhaustively studied, but with little success. However, results began to indicate that chemical composition was the most important variable, particularly the ratio of austenite-forming to ferrite-forming elements. The investigators then focused their attention upon the composition, and, in particular, upon the element titanium and its mode of alloying in the presence of other elements. A heat was obtained that could not be brought to the softness level of annealed 18-8. The response to cold-straining and aging* was very marked by previous standards, and, more important, cold-straining was found to be entirely unnecessary to produce the precipitation-hardening effect. The chemical composition of this heat was: C, 0.06 per cent; Mn, 0.54; P, 0.016; S, 0.016; Si, 0.58; Ni, 7.28; Cr, 17.60; Ti, 0.90; Al, 0.17. For some time the development work, particularly on composition, was carried

Jan 1, 1947