Search Documents

By R. B. Burt, J. A. Barr, I. S. Tillotson

THE pumping of solids in water suspension is an important part of many metallurgical and mining operations. In most cases, it is still in the rule of thumb category for which no universal formula has been developed, and much research is needed. Because of the limited and incomplete data available, this article may be classed as an experience paper, which is presented with the hope that some contribution will be made toward the development of the so-called universal formula. This formula, if and when developed, may be evolved from several factors, many of which are not now available for general application. The designing engineer is interested in obtaining accurate forecasts on: 1—the minimum velocities needed to prevent choke-ups in the pipeline, which in turn dictates pipe sizes, 2—power required for pumping, 3—pump selection. The basic factors for a given problem will include: 1—weight per unit of time of solids to be handled, 2—specific gravity of solids, for calculation of volume, friction and power, 3—screen analysis of solids with the colloidal acting, i.e., the slime fraction, a very important factor, 4— shape of particle or some means of determining a friction constant, 5—effects of percentage of solids, 6—development of a viscosity factor to be used in the overall calculations, 7—calculation of the lower limits of pipeline velocities permissible, 8—calculation of total head, pump horsepower, and 9—setting up of pump specifications. In certain limited cases horsepower and total heads and minimum velocities may be computed and a suitable pump selected from basic data, but in many cases, as in mining of Florida pebble phosphate, experience rather than a hydraulic formula still should be used as a basis of selection. Pumping Florida Pebble Matrix Pumping at the Noralyn mine of International Minerals and Chemical Corp. will be used as an example. Other areas will vary as to the characteristics of the matrix, especially the slime content. A typical screen analysis of this matrix is: +14 mesh, pebble size,* 2.1 pct; —14 +35 mesh, 11.4 pct; -35 +I50 mesh, 60.5 pct; -150 mesh, 25.0; total, 100 pct; moisture in bank, 20.0 pct; weight per cu ft in bank, 120 lb. The —150 mesh fraction may increase to as much as 35 pct in adjacent areas. When thoroughly elutriated, the matrix has a relatively slow settling rate, which is an important factor in permitting lower pipeline velocities without choke-ups. Exact data is not available to evaluate settling rates. For a factor of 100 a suspension of clean building sand in water is suggested. When pumping long distances, a quick settling matrix allows the coarser solids to settle out along the bottom of the pipeline, causing drag, turbulence, and increased friction. With a slow settling matrix as at Noralyn, turbulence acts to keep the solids in suspension at a lower friction head, regardless of the pumping distance. When the pebble content of the matrix, i.e., the + 14 mesh fraction, is in excess of 10 pct of the total solids, trouble may be expected from settling out even in normal pumping distances. To prevent choke-ups and maintain tonnage, an additional pump must be added in the long runs, where one pump would otherwise be satisfactory. A typical pulp handled is: total volume, 7800 gpm; water, 4500; solids pumped per hr, 4200 lb; sp gr pulp, 1.4; percent solids in pulp, 46.; pipe size, 16-in. ID; pulp velocity, 12.85 fps; probable critical velocity, 10 fps, as below this minimum velocity choke-ups would be numerous. In calculating friction heads the Armco handbook is used where a roughness factor based on 15-year-old pipe is set up. Because the pipe used in pumping matrix is smooth and polished because of the scouring action of the phosphate and its silica content, the head losses in the Armco table for water are practically the same as in pumping the Noralyn matrix through smooth pipe, plus the fact that conditions vary widely over short periods, making accurate determinations difficult to obtain. New pumps and pump changes are being tested continuously and a wealth of data built up. This has resulted in a substantial improvement and lower relative costs in pumping matrix. The Florida phosphate industry is constantly seeking to offset higher wage and material costs with improved technique. Until a few years ago a 12-in. discharge pump was commonly used, with heads as low as 80 ft. Sizes have gradually increased and heads more than doubled. For example, the following pump was placed under test at the Noralyn mine: make, Georgia Iron Works; size, suction 16 in., discharge 14 in.; impeller, 39-in. diam; motor, 600 hp, slip ring; full load speed, 514 rpm. The results were increased head, higher capacity than the older design, with fewer pumps in the line from mine to washer.

Jan 1, 1953

By Arthur Foote

AT THE end of the year 1914, the main North Star incline shaft had reached the 6300-ft. level, and encountered a vein dipping Southwest, or, exactly opposite to the North Star. Subsequent development failed to find the North Star vein continuing beyond this intersection, so the 6300-ft. level proved to be the bottom level of the North. Star vein, and very little ore was found below the 5300-ft. level. The new vein was called No. 1 vein. Development work carried on for the next 10 years discovered a third vein, called No. 2, branching off about 1200-ft. to the east, with a North-south strike and a west dip. No. 1 vein had about 900 ft. of backs above the 6300-ft. level before reaching the boundary line of the property, and No. 2 vein died out about 800 ft. above. During these 10 years, the money spent on development was increased from $54,000 in 1914 to $184,000 in 1924; the ore reserves steadily diminished until it was evident that the mine must close down unless by some means a large tonnage of ore could be developed quickly.

Jan 1, 1930

By M. B. Kasen

eralized strain equation appear quite different they are really identical. This identity can be shown in a simple mathematical rearrangement. Referring to Eq. [I], the substitution of ln(1 +?E) for ? (where ?E is the engineering strain) yields: a =s8- (s8?so)e?1/?c) ln(1 +s8??E) [4] or s =s8?(s8?so)(l +?E)-1 [5] Replacing (1 + cE) with its equivalent, (l/lo): s=s8?(s8?so)l/€c [6] Adding and subtracting the quantity (s8 - so) yields: s=s8?(s8?so)+ (s8-so) l-(^)l/£c [7] = s0+(s8?so)ri-(^0)1/^l [8] Letting n = 1/?c it follows that: This equation will be seen to be identical to the generalized strain expression in Eq. [3], the coefficients a and b being equal to so and (s8?so)/?c or n(s8?so), respectively. Confirmation of the relationship noted above was provided by fitting experimental stress-strain data5 for 304 stainless steel (total strain from 0.072 to 1.15) at room temperature at a true total strain rate of 4 x 10-3 sec-1 to Eqs. [I] and [3]. In this study nonlinear regression analyses were used to evaluate the equation constants. The results of this evaluation are presented in Table I. When these constants are used in Eqs. [I] and [3] the curves obtained are coincident. It will also be noted that the value of n is equal to YE,, the value of a is equal to so, and the value of b is equal to (s8 - so)/Ec. These equalities are illustrated in Table I where the Voce constants in parentheses were calculated from a, b, and n values. Excellent agreement is seen to exist. It is concluded, therefore, that the Voce equation is, indeed, identical to the linear expression involving generalized strain. In applying the generalized strain concept to stress-strain data, it has been noted3 that data within what was termed the transition region (first few points in the plastic flow region) must be excluded from the analysis in order to obtain the linearity in Eq. [3]. A similar exclusion applies in the use of the Voce equation since an expression which would describe the strain-hardening region would usually be found to be not too effective in the elastic-plastic fillet2 which connects the elastic line to the strain-hardening region. These considerations further substantiate that Eqs. [I] and [3] do indeed describe identical behavior. Note added in proof. Since this manuscript was submitted for publication, correspondence with Professor S. R. Davies, University of Edinburgh, (of Ref. 3) indicated that his associates have also confirmed the identity between the Voce equation and the generalized strain concept. It is sometimes desirable to obtain a small grain size in super-purity metals. Unfortunately, the absence of impurities, the low recrystallization temperatures, and the low activation energies for boundary motion result in rapid growth of relatively few grains when conventional recrystallization practices are used. For example, Arajs et al.1 were unable to obtain a mean grain diameter less than about 0.4 mm in iron containing 38 at. ppm of impurity. The <1 at. ppm purity range in many modern superpurity metals results in yet larger limiting grain sizes. It is the purpose of this communication to describe a technique by which mean grain diameters as small as 30 µ have been produced in aluminum having an impurity content < 0.5 at. ppm. The technique should be applicable to superpurity metals other than aluminum and has potential applications to grain refinement of commercial alloys. The necessary and sufficient requirements for production of a small grain size are as follows: a) a large number of potential nucleating sites must be created randomly within the cold worked material, b) sufficient thermal energy must be provided at a rate that will simultaneously activate a large fraction of the potential nuclei, and c) the grain growth must be stopped shortly after grain impingement.&apos; A high density of potential grain nuclei may be cre-

Jan 1, 1970

By Augustus Locke

The paper has two parts: the field argument and the microscopic argument. The field argument indicates that either the deep chalcocite has replacea sulfide of extraordinarily easy replaceability or it is hypogene. The microscopic argumentindicates that this sulfide, if it existed, must have been hypogene bornite; that this bornite must so excel known bornite in replaceability as to constitute a new variety; that the existence of this new variety is wholly unsupported by evidence; and that the deep Butte chalcocite is therefore hypogene. IN 1900, when the public first heard of "secondary enrichment" the Butte chalcocite seemed clearly supergene. Mining, through successive regions of leached capping, bonanza sulfide, and sulfide less rich, had paused at lean bottom levels which, though chalcocite-bearing, suggested the waning of copper. The deepest chalcocite, at 1500 ft., was yet too shallow to disturb the supergene hypothesis. But, with deeper mining, lean levels yielded to fat ones. Here and there they showed, within the same vein, an inverted distribution, chalcopyrite above and chalcocite below. To the miners&apos; astonishment, they carried chalcocite, unaffected by cross faults, on an independent course to the depth of 2500 ft. The pattern of ore distribution, hitherto revealed only in fragments, was now appearing in perspective, and, in the depth of the chalcocite, was beginning to make Butte differ from all districts where the chalcocite is indubitably supergene. The idea of hypogene origin at length came into favor; by 1913, when Sales1 advocated this origin, the argument had become a powerful one. This argument rested on field evidence; but, already, there was beginning to emerge microscopic evidence not included in this arugment. Especially pertinent was the proof that (1) The deep chalcocite lies in-mixed with bornite, often microscopic; (2) the deep chalcocite often replaces bornite; and (3) replacement of bornite by chalcocite is accom-

Jan 3, 1924

By Warren H. Westphal

For mining and exploration, and indeed the entire mineral industry, the first century of AIME has ended with far more problems than it began. Paradoxically, most of these problems have arisen not because, the industry has been unsuccessful, but rather because it has succeeded too well. Whatever the public demand for minerals over the past 100 years, it has somehow been met-and met at a price well within the public&apos;s ability to pay for the products. But as AIME moves into its second century, the past successes of mining and exploration are beginning to levy a tax on the future. Prospectors have already found most of the rich and ready ores, and miners have dug them out. New mineral assets grow progressively harder to come by, and as they do, the need for them grows inversely more pressing. How and where and at what cost can adequate supplies be found? How and at what cost can they be mined from heretofore inaccessible recesses deep underground and under the seas-or from vast surface tonnages containing only minor values? And once they are found or won, how can these assets be husbanded for generations to come? How also can they be extracted without injury to the land, air and water on which we and our successors must depend? And what constructive use can be made of the incidental materials now treated merely as wastes-sometimes at great expense?

Jan 1, 1971

By J. W. Cuthbertson, R. A. Cresswell

THE constitution of Cu-rich alloys with 1.5 to 13.5 pct Sn and 0.25 to 3.0 pct Be and the precipitation-hardening characteristics of alloys with 1.5 to 13.5 pct Sn and 0.25 to 1.0 pct Be have been examined. The hardness and tensile strength of the alloys examined increase markedly after solution treatment at 700°C followed by heat treatment at temperatures between 200" and 450°C. By a combination of cold work and heat treatment, hardness values similar to those exhibited by commercial Be-Cu alloys containing 2.25 pct Be can be obtained with ternary alloys containing 9 pct Sn and 0.75 pct Be and containing 10 pct Sn and 0.5 pct Be. Marked hardening effects occur with alloys containing even less beryllium. By heat treatment alone, a hardness value of 310 diamond pyramid hardness can be obtained from an alloy containing 10 pct Sn and 0.75 pct Be. Preliminary tensile tests have shown that an ultimate tensile strength of 110,000 psi with an elongation of 23 pct is obtainable by precipitation hardening an alloy with 8 pct Sn and 0.75 pct Be. The precipitation-hardening process has been followed microscopically for certain alloys and the inference is that, while the initial hardening effect is probably explained by the precipitation of the ß phase of the Cu-Be system, further hardening, proceeding at a much slower rate, also occurs, apparently as a result of precipitation of phases of the Cu-Sn system, particularly precipitation of the 6 phase at temperatures below 350". The presence of the e phase of the Cu-Sn system in certain alloys at temperatures below 350°C has been confirmed. Tin-bronzes are widely used in engineering applications where a combination of high strength and good resistance to corrosion is wanted. The maximum strength is induced in these alloys by cold working, and it would be an advantage for many purposes if high strength could be achieved alternatively by an age-hardening process. While Cu-Sn alloys have a good fatigue resistance they can be surpassed in this respect by Cu-Be, but the use of the latter alloy is limited by its high cost. If, by adding beryllium to tin-bronze, the properties of the respective binary alloys could to some extent be combined, a most attractive alloy should result. As pointed out by Raynor,¹ beryllium is on the borderline of the zone of favorable size factors for copper, and the solid solubility of beryllium in copper is consequently much more restricted than if the size factor were strongly favorable. The size factor is sufficiently favorable, however, to permit an increase in solid solubility with rise in temperature, and there is thus a composition range in which CU- Be alloys are susceptible to hardening by precipitation heat treatment. Although the a phase of the Cu-Sn system is similarly susceptible to precipitation treatment, the time necessary to establish equilibrium in commercial alloys of this type is usually so great that age hardening becomes impracticable. The addition of beryllium to Cu-Sn alloys would appear to offer a means of conferring on the latter useful age-hardening properties. Masing and Dahl² and others have, in fact, shown that the addition of beryllium to Cu-Sn a solid solutions renders these alloys susceptible to precipitation hardening and after such hardening confers on them an encouraging improvement in physical properties. If this improvement could be achieved by the addition of substantially smaller amounts of beryllium than are customarily found in binary Cu-Be alloys, the ternary alloys should possess economic advantages which might make them more attractive than the binary alloy for some applications. Binary Systems Copper-Tin: The constitution of these alloys is now reasonably well known and is summarized in the equilibrium diagram published by Raynor.³ The following observations, due to Raynor,¹ on the structure of those phases of the Cu-Sn system that are likely to be found in the ternary alloy system will facilitate the subsequent discussion on the examination of that system. The ß phase is an electron compound at the electron-atom ratio 3:2 and has a body-centered cubic crystal structure. This phase is stable only down to 586°C, at which temperature it decomposes eutectoidally into the a and y phases. The y phase has a structure that is also based on the cubic system. This phase is stable down to 520°C, at which temperature it decomposes eutectoidally into the a and d phases. The d phase is an electron compound (Cu³¹Sn8) which has a crystal structure analogous to that of 7 brass. This phase is stable from 590" to 350°C; on prolonged annealing at the latter temperature it breaks down into a mixture of the a and E phases. The e phase is an electron compound (Cu³Sn) having the electron-atom ratio 7:4. Its structure may be regarded as a superlattice based on the close-packed hexagonal system. This phase is stable from 676°C to room temperature. The primary solid solubility of tin in copper increases to a maximum of 15.8 pct as the temperature falls from that of the peritectic reaction to 586°C. The solid solubility remains constant from 586" to 520°C. At lower temperatures the solubility decreases progressively. Below 350°C the fall in solubility is pronounced and is associated with the precipitation of the e phase. This precipitation is very sluggish and does not normally occur under service conditions. Copper-Beryllium: The Cu-Be system has been investigated by Borchers&apos; and others. Raynor5 summarized the present state of information on it.

Jan 1, 1952

By Louis A. Panek

INTRODUCTION AND SUMMARY With respect to the geomechanics aspects, the primary technical objectives in mining by an undercut-cave method are to achieve a controlled, sustained caving of the mineral body and to remove the fragmented ore with a minimum of dilution from surrounding unmineralized rock, while maintaining stability or control of the rock structure around the access openings. The structurally ideal ore body probably does not exist. If the rock mass is so weak as to cave on a short span, it may tend to be too sticky for easy drawing and handling, or create special problems in regard to support of the access openings. If the ore is strong, caving may be difficult and the caved fragments may be of such a large size as to require special equipment for transferring the ore from the caved zone. Given enough time and money to generate data and conduct trials, engineering and ingenuity can devise an appropriate combination of mine layout, sequence of extraction, and mechanical equipment to achieve a technically successful caving extraction operation to meet the foregoing requirements in many types of deposits. The large capital investment involved, however, reduces the freedom to make major changes once the mine development is well under- way, and the penalties for failure to accurately anticipate operating conditions militate against selecting any but the most obvious candidates for mining by an undercut-cave method. The demonstrated capability to extract large, deep, economically marginal deposits by this low-cost, high-volume method of mining provides an incentive to develop a rationale for predicting the cavability and stability characteristics of a deposit prior to mining, so that the undercut-cave method may be extended to a much wider range of mineral deposit characteristics. The ultimate goal is to establish as explicitly as possible the quantitative interrelationships between the measured rock-mass characteristics, the caving span, the size distribution of caved ore fragments, and the sizes and locations of stable access openings. Lacking an understanding of these relation- ships, a designer may readily change some factor in the wrong direction (e.g., excessively reduce the distance between the extraction level and the undercut to increase the convenience of operations for the undercutting crew, increasing the frequency of repairs to the extraction-level support system) or create unnecessary problems elsewhere in the system by introducing a design change that can achieve only minimal improvement in the factor of direct interest (e.g., unnecessarily complicate the ore-transfer system by changing the orientations of the openings, with- out succeeding in the objective of improving the ground support conditions). Although successful predesign is the prime objective, subsequent modifications in mine lay- out and sequence of extraction operations are inevitable. In developing the modified solution, systematic experimentation based on an understanding of the underlying structural relationships, coupled with monitoring measurements of selected diagnostic structural-behavior parameters, can achieve an acceptable solution in a minimum number of steps, which is far superior to the typical operational trial-and-error approach, in view of the cost of implementing each successive change. Since a drill-core sample of ore rock from a successful undercut-cave operation may exhibit a uniaxial crushing strength in excess of 100 MPa, the caving of such a rock mass is now commonly believed to be ascribable to the presence of discontinuities such as joints or fractures throughout the ore body. An essential part of the present investigation was therefore to characterize the natural discontinuities at each of the test sites by measuring their attitudes and spacings. The term "fracture" is used herein in a general sense to include any planar discontinuity without implication as to its suggested mode of origin. Most, but not all, of the fractures are properly termed joints. As a point of departure we may consider the possibility that the rock mass is transected by three families of joints, each family possessing a distinct orientation, such that parallelepipeds of intact rock are delineated by the jointing. Even if cementation is absent between adjoining parallelepipeds, the undercutting of the rock mass will not necessarily initiate sustained caving--owing to the all-around confinement, an arch may tend to stabilize over the undercut unless prevented from doing so by the failures of key blocks of intact rock. Thus, although the jointing can be assumed to weaken the rock mass, creating preferred directions of

Jan 1, 1981

By Arthur T. Allen

THE Kingsport formation, a part of the Knox dolomite of Ordovician age, is composed of 538 ft of dolomitc and limestone. Numerous bands, layers and nodules of chert, arenaceous and shale zones are present. The characteristics displayed by these features have been useful in mapping, prospecting and mining. Perhaps a better understanding of the origin of these zones will increase their usefulness. Introduction The presence of numerous bands, nodules, and irregular bodies of chert within the Kingsport formation in the Mascot locality has long been recognized. Oder and Miller1 mention the general characteristics, but do not deal with the chert occurrences in detail. When the occurrence of chert is studied in fresh exposures underground, a variety of characteristics is noted which has been useful in correlation and in detailing the sub-surface stratigraphy. Although the writer has no desire to enter into a controversy over the origin of chert, many observations have been made of its local characterigtics. A detailed stratigraphic section is included which shows the position of the individual horizons discussed in the following paragraphs. The term "chertification" has been adopted from Fowler and Lyden2 for use here. It refers to the replacement of lime- stone by introduced silicic acid. The writer uses it to refer to the occurrencc of introduced or original chert in limestone and dolomite. In this writing "syngenetic chert" refers to chert which has been deposited contemporaneously with the enclosing limestone or dolomite. Also, it is considered to include interstitial silica shown by chemical analysis and insoluble residues. The term "epigenetic" is applied to all chert which has been introduced after consolidation of the rocks in which it occurs, regardless of the nature of the depositing solutions. Syngenetic Chert It is the belief of the author that a large percentage of the chert found in the Kingsport formation is syngenetic. The widespread occurrence of similar nodules and bands of chert in the same horizon far from one another and far from areas of deformation or alteration of the enclosing rocks is difficult to explain by infiltration of the silica after compaction of the enclosing rocks. When chert of this type does occur near zones of movement it is likely to be involved in faulting and brecciation which indicates that it was deposited prior to deformation. Older Epigenetic Chert There are several occurrences of nodules in the Kingsport which seem to be epigenetic as pointed out in the following examples: A cherty zone occurs 26 ft above the o bed (Fig =). This is not always present but is found in the greater part of mine work-

Jan 1, 1949

By Arthur T. Allen

THE Kingsport formation, a part of the Knox dolomite of Ordovician age, is composed of 538 ft of dolomitc and limestone. Numerous bands, layers and nodules of chert, arenaceous and shale zones are present. The characteristics displayed by these features have been useful in mapping, prospecting and mining. Perhaps a better understanding of the origin of these zones will increase their usefulness. Introduction The presence of numerous bands, nodules, and irregular bodies of chert within the Kingsport formation in the Mascot locality has long been recognized. Oder and Miller1 mention the general characteristics, but do not deal with the chert occurrences in detail. When the occurrence of chert is studied in fresh exposures underground, a variety of characteristics is noted which has been useful in correlation and in detailing the sub-surface stratigraphy. Although the writer has no desire to enter into a controversy over the origin of chert, many observations have been made of its local characterigtics. A detailed stratigraphic section is included which shows the position of the individual horizons discussed in the following paragraphs. The term "chertification" has been adopted from Fowler and Lyden2 for use here. It refers to the replacement of lime- stone by introduced silicic acid. The writer uses it to refer to the occurrencc of introduced or original chert in limestone and dolomite. In this writing "syngenetic chert" refers to chert which has been deposited contemporaneously with the enclosing limestone or dolomite. Also, it is considered to include interstitial silica shown by chemical analysis and insoluble residues. The term "epigenetic" is applied to all chert which has been introduced after consolidation of the rocks in which it occurs, regardless of the nature of the depositing solutions. Syngenetic Chert It is the belief of the author that a large percentage of the chert found in the Kingsport formation is syngenetic. The widespread occurrence of similar nodules and bands of chert in the same horizon far from one another and far from areas of deformation or alteration of the enclosing rocks is difficult to explain by infiltration of the silica after compaction of the enclosing rocks. When chert of this type does occur near zones of movement it is likely to be involved in faulting and brecciation which indicates that it was deposited prior to deformation. Older Epigenetic Chert There are several occurrences of nodules in the Kingsport which seem to be epigenetic as pointed out in the following examples: A cherty zone occurs 26 ft above the o bed (Fig =). This is not always present but is found in the greater part of mine work-

Jan 1, 1949

By Hans Lundberg

GEOPHYSICAL methods as described in technical articles generally fail to answer the questions of prospectors and geologists as to which method they should apply and what information they may expect from their application. This article is an attempt to discuss the use of electrical methods with special reference to the prospecting for orebodies and the map¬ping of geologic structure. Especially on virgin ground, geological reconnaissance should precede electrical prospecting, with the object of outlining carefully the orebearing rock and determining the possibilities of elec¬trical prospecting. No electrical survey will then be carried out on ground which, for geological reasons, may be considered barren or where the electrical meth¬ods are inapplicable. As the success of electrical prospecting depends on the difference in conductivity between the ore and the country rock within which the orebody is inclosed, the conductivity of the two should be considered and de¬termined, if possible. The conductivity of an orebody depends on the distribution of conductive ore minerals and, in addition, on its size (length, width and depth). Most minerals with metallic luster show good electrical conductivity; for instance, the sulfides. Zinc-blende is an exception, but as it is often associated with the ore minerals of good conductivity (for instance, pyrite or galena), there is likelihood also of finding zinc.

Jan 1, 1930

By P. B. Scotland

THE mines of the Arizona Copper Co. are situated in the Morenci-Metcalf copper district in southeastern Arizona. This copper-bearing district covers a triangular mountainous area of about 3 square miles, rising abruptly from the gravel plateau of the surrounding country. In this area, an immense intrusion of porphyry has displaced, shattered, and engulfed the shales, limestones, and quartzites formerly bedded on the basal granite. Outcrops of oxide ore were discovered in 1873, and these surface ores were found to connect in depth with large bodies of high-grade oxide ores in the limestones and shales. The smelting of these ores in blast furnaces continued until about 1893, when the rapid exhaustion of the high-grade ore led to the discovery and exploitation of the low-grade sulphide ores in the adjoining porphyry. Methods of concentration were then devised and the low-grade ores finally rendered profitable. The Arizona Copper Co. and the Detroit Copper Mining Co., operating in the same district, were the pioneers in the successful development of the low-grade "porphyry" properties of to-day. The largest mines of the Arizona Copper Co. are the Humboldt and Clay at Morenci, and the Coronado, Metcalf, and King at Metcalf. These mines produce about 4,000 tons daily of concentrating ore containing from 2.5 to 2.8 per cent. copper. The topography of the country is very rugged and mining operations are conducted principally through adit levels. A few of the mines are opened by shafts, the deepest being 1,100 ft., in the Coronado mine. ORE OCCURRENCE The low-grade sulphide ore occurs as: (1) disseminated deposits in the main stock of quartz porphyry; (2) lode deposits in fault fissures in granite. The high-grade oxide ores were found as tabular deposits in limestone and shale close to contacts with porphyry. Low-grade oxide ore formed the outcrop of some-&apos; the sulphide orebodies; the majority of the outcrops, however, were barren.

Jan 2, 1915

By Edward H. Robie

EIGHT years ago in this department we had a column on the daiquiri cocktail, which, as we pointed out at that time, was invented by mining engineers. Since then we have said little or nothing about alcoholic drinks, but having set the precedent perhaps we may now pass along a little information about martinis. We have observed that as an aperitif the martini has become increasingly popular with men, so much so that we always feel a bit peculiar if we order something else. And the call is not for just a martini either; it must be a dry martini, and some of our friends are extremely particular on this point. The matter has achieved such importance that The New York Times devoted half a page to it a few Sundays back. Several recipes are given which may be useful to some of our members when entertaining visitors from this part of the country: The standard martini is said to be half gin, half Italian vermouth, two dashes orange bitters, and a pickled onion and twist of lemon peel. This progresses to the very dry martini, which calls for five parts gin and one part vermouth with an onion, olive, or lemon peel. Several alternatives are offered for the manufacture of the very, very dry martini. One is to pour a little vermouth into the mixing glass and pour it out again before mixing gin and ice. A second way is to put the ice in a sieve, hold it over the sink, and pour a little vermouth over it; then put the ice in the mixing glass. A third is to let the draft from an electric fan blow across an open vermouth bottle toward the mixing glass. Then the ultimate is the awfully dry martini, obtained by setting the vermouth bottle next to the mixing glass and turning the bottle slowly so that the label is exposed to the gin for perhaps a second. The Times notes that Mr. Martini himself personally prefers vermouth and soda.

Jan 1, 1952

By Becket, Frederick M.

CHROMIUM is but one hundred and thirty years of age-a mere youngster as related to many metals that&apos; have speeded world progress. It was Vauquelin of France who proved conclusively that the so called red lead of. Siberia contained a new element. The variety and characteristic colors of the compounds suggested the name chromium. He also succeeded in reducing oxide of chromium to the metallic form and described the product as very brittle, infusible, needle- like crystals on which acids had very feeble action. His metal was not pure chromium, of course; it must have contained appreciable carbon in the combined form as a result of reducing the oxide by carbon at high temperatures. Vauquelin&apos;s description in 1798 of this work is a gem-indeed, literally, he went so far as to discover the presence of chromium oxide in the emerald. The metallic product did not seem to interest Vauquelin greatly, but a new chemical industry began shortly after his discoveries.

Jan 1, 1928

By Emanuel Trotz

As the long-felt need of a reliable and easily-managed pyrometer has now been fully supplied, by the latest form of Professor Wiborgh&apos;s pyrometer, an account of this instrument will, per-

Jan 1, 1893

By William P. Blake

As the storage of water for agricultural and mining purposes in the arid regions of the West is now receiving much attention by the people and their representatives, some facts coucerning the greatest pioneer enterprise for the purpose should appear on our records. I refer to the dam and reservoir at Walnut Grove, in Yavapai county, Arizona Territory, which was finished in the winter of 1887, and is known as the Walnut Grove Dam, It is not my intention at this time to give a full description of

Jan 1, 1889

By Halbert Powers Gillette

FROM the known laws of physical chemistry I believe it can be shown that progressive mass movement of water solutions in channels has seldom been the means of ore-concentration in veins. It is my purpose in this paper to show that the force known as “osmosis” has been the principal factor in ore-formation. Convection-currents have doubtless supplemented osmosis, and the two working together have been the agencies that have gathered the scattered particles of rare minerals into the larger masses which are called ore. Osmosis is commonly thought of as a vague, feeble force that causes slow diffusion of dissolving matter through the solvent. That it is a measurable force, often of great intensity, few know, except those who are familiar with the laws of modern physical chemistry. Therefore, I may be pardoned for going briefly into the elementary mathematics of osmotic pressure and of convection-currents. The velocity of water moving through any channel is given by the Chézy formula: (1) v = c [/rs], in which r is the hydraulic mean radius; s, the slope of the channel in which gravity is the sole propulsive force; and c, the coefficient of roughness of the sides of the channel. From this formula it is evident that the smaller the channel, the smaller the velocity of water under a constant head. In rock-crevices, therefore, where the head is constant, water moves much more slowly than in large fissures, and in moving through sand or porous rock it is to an even greater degree retarded. Hence, if a mass of water-saturated sand be heated, the finer the sand-grains, the more slowly will the temperature rise at parts remote from the source of heat. Conversely, cooling is retarded the smaller the interstices or channels through which the convection-currents move. The importance of this

Jan 1, 1913

By Ralph B. Stevens

INTRODUCTION Underground fires continue to be one of the most serious hazards to life and property in the mining industry. Although underground mines are analogous to high-rise buildings where persons are isolated from immediate escape or rescue, application of technology to locate and control fire hazards while still in their controllable state is slow to be implemented in underground mines. Even in large surface structures such as hotels, often only fire protection systems which meet minimal laws are implemented due to the high cost of adding extensive extinguishing systems, isolation barriers, alternate ventilation, escape routes and alarm systems. Incomplete and ineffective protection occasionally is evidenced where costs would not seem to be a factor, such as the $211 million MGM Grand Hotel fire November 21, 19801. Paramount in increasing fire safety and decreasing the threat of serious fire is early warning followed by proper decision analysis to perform the correct action. However, very complex fire situations can be produced in structures such as high-rise buildings and underground mines simply because of the distances between the numerous fire-potential locations and fire safe areas. Other complexities arise when normal activities occur that emit products of combustion signaling a fire condition to a sensitive fire/smoke sensor. For example, the operation of diesel equipment or the performance of regular blasting can produce combustion products that reach the sensitive alarm points of many sensors2. Smoke detectors for surface installations provide fire warning when occupants are at a distant location or when sleeping, thus greatly reducing injuries and property damage. However, when installed in the harsh environments of underground mines, fire and smoke detection equipment soon becomes inoperative, unreliable, or requires excessive maintenance. The U.S. Bureau of Mines has performed many studies and tests to improve fire and smoke protection for underground mine workers3. This paper describes several USBM safety programs which included in-mine testing with mine fire and smoke sensors, telemetry and instrumentation to develop recommendations for improving mine fire safety. It is hoped that the technology developed during these programs can be added to other programs to provide the mining industry with the necessary fire safety facts. By recognizing fire potentials and being provided with cost-effective, proven components that will perform reliably under the poor environmental conditions of mining, mine operators can provide protection for their working life and property equal to that which they provide for themselves and their families at home. The basis of this report is two USBM programs for fire protection in metal and nonmetal mines4,5 and one coal program6. The data was collected beginning in May 1974 and continuing through the present with underground tests of a South African fire system installed at Magma Mine in Superior, Arizona, and a computer-assisted, experimental system at Peabody Coal Mine in Pawnee, Illinois. The conduct of each program was as follows: • Define the problem and its magnitude in the industry • Develop concepts to solve or diminish the problem • Review available hardware or systems approaches to fit the concepts • Install and demonstrate the performance of a prototype system through fire tests in an operating mine. MINE FIRE FACTS Whether in coal or metal and nonmetal mines, the potential severity of fire hazard is directly related to location. As shown in Figure 1, fire in intake air at zones A, B, C or D can cause contamined air to route throughout the mine quickly if not detected, isolated or rerouted. Causes and location of former metal and nonmetal fires are represented in Table 1; the cause and location of fatalities and injuries is shown in Table 2. Coal-related fires and their impact on deaths and injuries are graphed in Figure 2; their locations are described in Table 37. Significantly the table shows that the hazard to personnel was three times greater for fires occurring in shaft or slope areas, and the percentage of deaths and injuries was four times that of other areas. Number of Persons Affected A 129-mine sample indicated that from 8 to 479 employees per shift work in underground metal and nonmetal mines, and that deeper mines have larger populations, as shown in Figure 3. Coal mining relates similar employment, and a 16-state sample of 670 mines employing at least 25 persons shows the distribution in Figure 4. Drift mines accounted for 58 percent of the sample but employ only 45 percent of the underground workers.

Jan 1, 1982

By M. J. Sinnott, W. R. Kiessel

The creep characteristics of commercially pure titanium sheet in the annealed state, cold-worked state, and cold-worked and recovered state in the temperature range from 75&apos; to 750°F have been determined. Titanium has been found to exhibit strain aging characteristics. The effect of strain aging on creep has been determined. A possible explanation for the poor creep properties of titanium is proposed. THE metal titanium exhibits many desirable properties but results on its creep properties have been somewhat disappointing. The creep strength is low even though the material has a very high melting point.&apos; The present work was undertaken to determine the creep strength of titanium in various conditions; annealed, cold-worked, and cold-worked and recovered and to determine why titanium shows such relatively poor creep properties. The general procedure followed in this research consisted in obtaining the usual mechanical prop- erties such as creep strength, short time tensile strengths, and hardness on materials treated to a controlled degree of internal strain, as determined by X-ray diffraction measurements, and their subsequent interpretation in terms of this internal strain. The material used in this work was sheet stock taken from one heat of commercially pure titanium. As-received, this sheet was 0.060 in. thick. The analysis was given as 0.037 pet C, 0.023 pet Si, 0.50 pct W, 0.063 pct Ni, 0.08 pct Fe, and the remainder titanium. The oxygen and nitrogen were unreported but generally are about 0.2 pct in commercial heats. In order to put the material in a state of minimum internal strain all the sheet was given an anneal in a static argon atmosphere for 1 hr at 1600°F prior to processing and testing. The microstructure of the material after this treatment was essentially a single-phase solid solution of uniform equiaxed grains. For the studies on the cold-worked sheet, the material was reduced by rolling in a two high, 5 in. mill. Rolling was done at room temperature in passes

Jan 1, 1954

By R. S. Rickard, M. C. Fuerstenau

Anodic polarization curves for iron dissolution and cathodic polarization curves for copper deposition and ferric and hydrogen ion reduction were studied. These results were used to predict the relative rates of the reactions: The rates of the first two reactions were found to be first order with respect to the reacting ion, and the rale-controlling step was diffusion of the ions to the callzode surface. The rate of hydrogen ion reduction in an oxygen-free solution is dependent on the reciprocal of the square root of the hydrogen ion activity. In solutions containing oxygen, the rate of hydrogen reduction becomes dependent on the square root of the partial pressure of oxygen. At equal concentrations copper precipitation occurs about twice as fast as ferric ion reduction. In an air-saturated solution containing 0.01 M cupric ion at pH 2, the rate of hydrogen ion reduction zs about 10 times slower than that of copper precipitation. At pH values below 3, the rate of hydrogen reduction in oxygen-free solutions is very slozu. COPPER cementation has been utilized industrially for many years as a means of recovering copper from aqueous solutions. There are many different types of cementation plants, but all simply provide a means of contacting iron with relatively dilute copper solutions. In the past little or no attention has been paid to rates or mechanisms of the reactions involved. As a result, this and other studies&apos;-3 have been undertaken recently to establish the important parameters in this system. The reactions involved in copper cementation by iron are: Since transfer of charge is involved in every case, these reactions should be considered from an electrochemical point of view. In any electrochemical system involving electrolytic conduction, passage of electrons necessitates ion transfer to the respective electrodes according to Faraday&apos;s law. The current in the system will be proportional to the rate of ion transfer, and, therefore, when the current in the galvanic cell is known, the rates of the reactions involved can be determined. Galvanostatic electrode measurements5" are applicable for these electrochemical studies, in that with this technique polarization curves (current density vs electrode potential) are established by impressing a constant current through an electrode and measuring the electrode potential. Once the current density, electrode potential, and reacting area are known for each reaction in this cementation system, the rates of the iron-consuming reactions can be determined. EXPERIMENTAL MATERIALS Several metal electrodes were used in this investigation; they are shown in Table I. Solutions were made with reagent-grade salts and conductivity water. Air, nitrogen, and oxygen were employed. All of these gases were saturated with water and degreased prior to use. EXPERIMENTAL PROCEDURE The experimental work was divided into two general areas. The first area involved galvanostatic measurements, which were used to determine the rates of reactions as a function of various parameters. The second area comprised actual cementation experiments to check the rates predicted from the electrode measurements. Galvanostatic Electrode Experiments. Polarization curves were obtained using a standard galvanostatic technique5&apos;= with the apparatus shown in Fig. 1. The various electrode polarization experiments were run the same way except for changes in solution composition, polarity, and type of measured electrode. The general procedure involved the following steps: 1) a solution was made 0.5 M in sulfate ion and to the desired cation concentrations; this solution was placed in a constant-temperature bath and saturated with the desired gas; 2) the electrodes were cleaned and placed in the electrode holder; 3) the previously cleaned apparatus was assembled and immersed in a constant-temperature water bath (temperature controlled to ± 0.05"C); 4) the electrode was then positioned; the solutions were introduced, and the polarization meas-

Jan 1, 1969

By C. R. Dale

IT IS the purpose of this paper to point out a number of the most common causes of crooked holes; to outline methods of drilling and straightening which to my personal knowledge have proved successful in numerous cases; to describe some of the characteristics of holes which, though not crooked in an exaggerated sense, may still cause serious mechanical trouble if not recognized and properly remedied; and to define clearly the part of oil-well surveying in the concerted effort operators generally are making to keep their wells straight from spudding to completion

Jan 1, 1931