Search Documents

By R. Hogg, F. F. Aplan, P. B. Bradley, M. F. Placha

Particle size distributions of the solids fraction in typical coal preparation plant black water have been evaluated. The carbonaceous and mineral fractions were found to have distinctly different size distributions: the mineral matter being significantly finer than the carbonaceous material in all cases. Based on analyses of 13 samples obtained from the Appalachian, mid-continent and western regions of the US, it was found that, on the average, 83% of the mineral particles but only 41 % of the coal particles were finer than 44 pm (325 mesh). Typically, the size distributions of the mineral matter fraction tend to be bimodal, probably due to the presence of relatively coarse quartz, calcite, pyrite, etc., together with much finer clay particles.

Jan 1, 1981

By Bernard MacDonald

Introduction. OF the treatment of the slime-pulp of gold- and silver-ores by cyanidation, agitation is an essential part. When prepared for treatment, this pulp, consisting of ore reduced to such fineness that approximately 80 per cent. of it will pass through a 200-mesh screen, is mixed with a certain proportion of water, carrying in solution the quantity of cyanide (KCN) and other chemicals required. The water-constituent of the pulp thus prepared usually ranges from 1 to 2 parts by weight to 1 of the dry ore. Thus constituted', the pulp is charged into treatment-tanks, the shape and capacity of which vary, according to the quantity of pulp to be treated daily and the method of agitation to be employed. Tanks have no other function in a cyanide-plant than that of being economical and convenient containers or receptacles for holding the pulp, solution, or water used in the operations. It is by agitation that the solids in the pulp charged into the tanks are kept in suspension in, and mixed with, the solution in the proper proportions required for the treatment. If the proper mixture of solution to solids be determined to be 2 to 1 by weight (which is, approximately, 5 to 1 by volume), this proportion should be maintained in every part of the charge ; -that is, each solid particle of the pulp, whether it be of 180- or 400-mesh size, should, be surrounded by five times its own volume of solution throughout the whole period of treatment. The reason is, that the amount of chemicals ascertained to be necessary for dissolving the gold and silver contained in the solids, is held in uniform solution in the water-constituent of the pulp, and, therefore, the determined proportions of solution and solids must be maintained at all times during treat-

Apr 1, 1912

By AIME AIME

ALTHOUGH the present economic depression is felt in the petroleum industry, probably as much as in any other branch of American industry, the Petroleum Section of the Institute was well represented at the general sessions on Monday and at all of the seven division sessions on Tuesday, Wednesday and Thursday. The seven sessions of the Division were so arranged as not to conflict and thus permitted members to hear the programs of all sessions.* The first meeting of the Petroleum Division was held on Tuesday afternoon; a joint session on engineering research and production engineering. The following papers were presented:

Jan 1, 1931

By H. P. Greenwald

THE Committee on Rock-Dusting was formed after the fall meeting of the Coal Division in Chicago in 1938. Its primary task was to study the recommended American practice for rock- dusting coal mines to prevent coal-dust explosions as approved by the American Engineering Standards Committee. After approximately two years' work he committee concluded that although certain portions of the recommended practice could well be revised, information needed for a logical revision was not at hand, and it was inadvisable, therefore, to make revisions

Jan 1, 1943

By Bjorge, Guy N.

MINING method improve through the gradual process of evolution and in 1340 there were no marked outstanding innovations. On the other hand refinements of detail and betterment: in equipment design continued to progress. Among the most important changes have been the increased application of trucks and highway equipment, including tractors and bull- dozers, to open-pit mining as exemplified by Phelps Dodge's Morenci operations; the Mesabi iron range; and the Tri-State district. Mass or bulk handling contributed its part underground with slurhers and conveyors at Consolidated Coppermines and slushers at Climax; and in open-pit mining. conveyors found increased use on the Mesabi range.

Jan 1, 1941

By John J. Collins

The plight of the Japanese mining business is pitiful. Coal mines were given the highest priority for all materials they needed, yet between the end of the war and June 1948, the government was obliged to subsidize them to the extent of 22 billion yen, this being the difference between the consumer's price and the producer's price. Most of the metal mining companies have been operating at only one fifth to one third of war-time production rates, and financial losses have been terrific. The chief difficulties have been a plethora of office workers and a dearth of equipment, supplies, and miners. The principal material needs at metal mines are steel rails. cars, plates, nails, rubber hoses, and belting, to say nothing of modern core drills which are totally lacking. Until recently the great shortage was in coal; for lack of fuel the smelters and factories failed to produce the very metals and equipment now needed to operate the mines. Nation-wide shortages have created a monstrous inflation of prices throughout all the economy, currently amounting to 200 times the prewar figures. For example, the price of copper ranged from 500 to 900 yen per metric ton for many years until 1937, but in mid-1948 producers were

Jan 1, 1949

By H. J. C. MAC DONALD

THE mining engineer must have a chest of books snug enough for a camelback or to be stowed away in a canoe; at the lowest possible cost, as he needs it the most in those early years when he earns the least; but at the same time one having an unusually wide range, for he may have to cut down a forest, put up a sawmill, build mine towns, construct dams, power houses, power lines, and railroads. In fact he may be called upon for many unexpected accomplishments and all in extension of the characteristically broad demands of his profession. Suppose that an average mining engineer with a thorough theoretical training and a specialized mining education has accumulated, during a cosmopolitan experience, a complete and up-to-date library, but, unfortunately, in accepting a long term assignment to a far country he is forced to discard the greater part of

Jan 1, 1925

By D. Cox, M. J. Duggin, L. Zwell

The carbides of approximate composition and Mn have been studied using X-ray diffraction techniques. Those carbides of the type (Fe,Aln)zC ave isostructural with cementite. The cell pararmeters a and c have minimum values at approximately 10 at. pd substitution of manganese for iron; no satisfactory explanation has yet been found for this phenomenon. The carbide fFeMn4)C has a monoclinic unit cell whose dimensions are close to those of ,11,15Cz A neu-troip-dij~ractiot~ study of (F'eAlrz4)C~ reveals that, like MnsCZ, it is isostructural with Pd5Bz. The iron and manganese atoms occupy the palladium atom sites, while the carbon atoms were found to have the same atomic coordinates as the hovon atoms. A neutrorr-diffraction study of indicates that the carbon-atom positions are very close to those occupied in (Fez.,ll/lr~,.3)C. In both carbides studied, tlre iron and manganese atomzs were found to be essentially randomly distributed, although, in the case of (Fe,.811fn1.2)C, it is possible that there may be a slight preference of manganese atoms for- the general (d) positions and a corresponding slight preference of iron atoms for the special (c) positions. It has been found that a complete range of solid solution exists between Fe3C and Mn3C at 1050°C,I although Mn3C becomes unstable when the temperature is reduced to 95O0C,' and can only be retained by rapid quenching. It is also known that a complete range of solid solution exists from Fe5Cz to M~SC~,~ although the stability range of carbides of the type (Fe,Mn)sCz as a function of the relative proportions of iron and manganese is not known. X-ray examinations of Oh-man's carbide3 and Spiegeleisenkristall,~ which have the approximate compositions (Fe3.67Mnl.33)C2 and (Fe3-,Mn,)C, where x lies between 0.4 and 1, respectively, have been made. The following carbides have also been studied: ] The lattice parameters determined during these investigations are listed in Table I. It is seen that carbides of the type (Fe,Mn)sCz have a monoclinic unit cell while carbides of the type (Fe,Mn)3C have an orthorhombic unit cell. It is evident that the variation of lattice parameters with manganese content is not linear for carbides of the type (Fe,Mn)3C. The coordinates of the atoms in (Fe2.7Mno.3)C have recently been determined by single-crystal analysis., The fractional atomic coordinates have been shown by Fasiska and jeffrey to be in good agreement withj those deduced from an earlier analysis of Fe3C by Lipson and etch.' However, it was impossible to determine whether iron and manganese atoms occupied ordered positions because of the small difference between the atomic scattering factors of iron and manganese. The atomic positions in Mn5Cz (Refs. 8 and 9) and Fe5C2 (Refs. 7 and 8) have been obtained only by comparisons made with the isostructural compounds P~SB~.' Since X-ray diffraction techniques were used in these investigations, accurate positioning of the carbon atoms, which have a low atomic scattering factor, was difficult. No attempt has been made to determine the atomic positions in the other carbides previously studied. It was felt that an investigation of the lattice parameters of a number of intermediate carbides of the types (Fe,Mn)sCZ and (Fe,Mn)& would be of interest. It seemed likely that a neutron-diffract ion study of such carbides would indicate whether ordering occurred between the iron and manganese atoms because of the large difference between the neutron-scattering cross sections of iron and manganese. It also seemed probable that such an investigation would provide a determination of the atomic coordinates of the carbon atoms. I) EXPERIMENTAL DETAILS Specimens, each weighing approximately 20 g, were carefully prepared according to the following proportions: The components were 500-mesh powders of 99.995 pct purity iron and spectroscopically pure carbon and a 200-mesh powder of 99.995 pct purity manganese. The component powders were intimately mixed by prolonged shaking, then each specimen was inserted into a spot-welded cylindrical container of tantalum foil, whose end was closed but not sealed. Each specimen in its envelope was then sintered at 1050° C for 24 hr in a thin-walled evacuated quartz capsule, such a time having been previously found sufficient for equilibrium to be attained.' Each specimen was then quenched in order to attempt to retain the high-temperature phase, as the literature indicates that transformations may occur on cooling. Debye-Scherrer X-ray photographs were taken of each specimen using a 114.6-mm-diam camera, Fig. 1, patterns 2 to 6. The exposure time was 6 hr using filtered iron radiation at a tube voltage of 40 kv and a tube current of 12 ma.

Jan 1, 1967

By J. E. Tobey

THERE are a lot of good things about this great industry of ours. Let us stop commiserating and consider some of the things that are right in this business. Coal is number one in the basic material industries. Our civilization owes more to it than to any other basic commodity. We are literally immersed in the benefactions of coal. In cur man-made world it is indispensable and we are constantly surrounded by objects, materials, and services which owe their existence to coal. Practically all the important materials, such as iron, steel, brick, cement, lime, rubber, glass, cotton, and wood have felt its magic touch.

Jan 1, 1939

By Frank C. Greene

Drilling in Missouri in 1944 was nearly treble the rate of 1943 because of continued development of the Tarkio pool in Atchison County and the preparation of a pool in Jackson County for a water-injection project. The pipe line from the Prairie Point gas pool in Platte County was in operation throughout the year of 1944, but several of the shallow oil pools in Cass and Jackson Counties were off production during much of 1944 because of a shortage of help. Table I gives a summary of activities by counties. The total footage drilled was 41,475 .ft., of which 21,187 ft. was by rotary tools and 20,268 ft. by cable tools.

Jan 1, 1945

By B. E. Eakin, A. L. Lee

Atmospheric pressure viscosity values For light hydrocarbons were calculated by a simple mixing rule based on the Sutherland constants for pure components. This method was further extended so that the atmospheric pressure viscosity of a mixture may be calculated based on the molecular weight information only. INTRODUCTION A proven method for estimating the gas-phase viscosity of a mixture is the one by Herning and zipperer.l This mixing rule has the following form: One method for calculating the pure component viscosity i is the Sutherland equation,2 which has the following form: The Sutherland constants B and S are determined from experimental data. A set of Sutherland constants for light hydrocarbons based on the data of several investigators3-5 is presented in Table 1. APPLICATION The Herning-Zipperer equation and the Sutherland equation were used to obtain an equation for calculating the gas-phase viscosity of light hydrocarbons. This equation has the form, Eq. 3 was used successfully in the study of methane-n-butane mixtures.6 Further analysis indicated that the Sutherland constants are a function of molecular weight.7 The gas-phase viscosity may be calculated based on molecular weight information only. The following equation was developed: The atmospheric pressure viscosity of ethane, propane, n-butaneand four methane-propane mixtures calculated on the basis of Eq. 6 are compared with the data of other investigators in Tables 2, 3, 4 and 5, respectively. A plot of atmospheric pressure viscosity vs molecular weight based on Eq. 6 is presented in Fig. 1.

Jan 1, 1965

By G. Sachs, G. Espey

It is well known that high residual stresses are created in tubing by the sinking process, in which no internal tool or mandrel is used.l-4 In this process, the wall thickness is usually slightly increased.4,5 In tube drawing with a plug, the residual stresses are gradually reduced with increasing reduction of wall, and, by the conventional approximation methods of stress measurement, no stress is detected in tubing in which the wall reduction is over 50 per cent of the total reduction in cross-sectional area.l,6 It has also been observed that higher stresses are set up by the use of wide-angle dies than by acute dies.? 'he actual stress distribution in drawn tubing has been investigated by a few workers,7"9 but has not been related to the conditions of the drawing process. Some attempts have been made to correlate accelerated cracking tests for stresses in brass products with the magnitude of the circumferential stresses and the condition of the metal. l-10 Materials and Preparation The material used in this experiment was commercial cartridge-brass (70 per cent Cu, 30 per cent Zn) tubing in the straightened and annealed condition.† This tubing was of various outside diameters and had a wall thickness of 0.032 in. It was sunk to 1/2-in. outside diameter by means of an experimental 10,000-lb. hydraulic draw-bench, with a maximum drawing speed of 8 ft. per minute. All dies were of 1/2-in. diameter. Various die materials and contours were used in order to study the effect of die design on residual stresses in the tubing; the specifications for the dies are given in Fig. I. Castor oil was used throughout as lubricant. Chattering occurred in sinking some of the tubing, particularly when dies having the more acute angles were used, but the tubes showing chatter marks did not differ markedly from those with a smooth surface regarding the magnitude of residual stress. The source of the chattering has not yet been revealed. The wall of the tubing becomes thicker during s nking, as previously observed.4,5 The increases in wall thickness were 3, 7 and 9.5 per cent on the average for 6, 20 and 33 per cent reductions in diameter, no effect of the contour being noticeable. The reductions mentioned throughout this investigation do not consider this fact, but are reductions of the outside diameter. For the evaluation of the residual stress two fundamentally different methods were used. The approximation methodl,ll of splitting a certain length of tubing was employed to obtain a bird's-eye view of the effect of various drawing conditions on the circumferential stress measured by the diameter change occurring On splitting. For

Jan 1, 1942

By G. Sachs, G. Espey

It is well known that high residual stresses are created in tubing by the sinking process, in which no internal tool or mandrel is used.l-4 In this process, the wall thickness is usually slightly increased.4,5 In tube drawing with a plug, the residual stresses are gradually reduced with increasing reduction of wall, and, by the conventional approximation methods of stress measurement, no stress is detected in tubing in which the wall reduction is over 50 per cent of the total reduction in cross-sectional area.l,6 It has also been observed that higher stresses are set up by the use of wide-angle dies than by acute dies.? 'he actual stress distribution in drawn tubing has been investigated by a few workers,7"9 but has not been related to the conditions of the drawing process. Some attempts have been made to correlate accelerated cracking tests for stresses in brass products with the magnitude of the circumferential stresses and the condition of the metal. l-10 Materials and Preparation The material used in this experiment was commercial cartridge-brass (70 per cent Cu, 30 per cent Zn) tubing in the straightened and annealed condition.† This tubing was of various outside diameters and had a wall thickness of 0.032 in. It was sunk to 1/2-in. outside diameter by means of an experimental 10,000-lb. hydraulic draw-bench, with a maximum drawing speed of 8 ft. per minute. All dies were of 1/2-in. diameter. Various die materials and contours were used in order to study the effect of die design on residual stresses in the tubing; the specifications for the dies are given in Fig. I. Castor oil was used throughout as lubricant. Chattering occurred in sinking some of the tubing, particularly when dies having the more acute angles were used, but the tubes showing chatter marks did not differ markedly from those with a smooth surface regarding the magnitude of residual stress. The source of the chattering has not yet been revealed. The wall of the tubing becomes thicker during s nking, as previously observed.4,5 The increases in wall thickness were 3, 7 and 9.5 per cent on the average for 6, 20 and 33 per cent reductions in diameter, no effect of the contour being noticeable. The reductions mentioned throughout this investigation do not consider this fact, but are reductions of the outside diameter. For the evaluation of the residual stress two fundamentally different methods were used. The approximation methodl,ll of splitting a certain length of tubing was employed to obtain a bird's-eye view of the effect of various drawing conditions on the circumferential stress measured by the diameter change occurring On splitting. For

Jan 1, 1942

Albin, B. R Billings, Mont. '28 Amster, Nathan L 25 Broad St., New York, N. Y. '28 Bache, Jules S 42 Broadway, New York, N. Y. '28 Barrett, C. P 5338 Harper Ave., Chicago, 111. '28 Bayless, William S Russ Bldg., San Francisco, Cal. '28 Bean, Louis, H 60 E. 42nd St., New York, N. Y. '28 Beatty, Ross J Room 604, 6 N. Clark St., Chicago, III. '28 Benwell, Oswald F Hold Mags. '28 Beymer, Albert S., V.P., Keystone National Bank Pittsburgh, Pa. '28 Blumenthal, Hugo 44 Pine St., New York, N. Y. '28 Boettcher. Charles Ideal Cement Bldg., Denver, Colo. '28 Bowlus, Thomas H., Banker, Pres., Allen County State Bank Iola, Ran. '28 Brown, Colvin B Chamber of Commerce, Washington, D. C. '28 Burt, Maxwell Struthers Southern Pines, N. C. '28

Jan 1, 1934

Albin, B. R Billings, Mont. '28 Amster, Nathan L 25 Broad St., New York, N. Y. '28 Bache, Jules S 42 Broadway, New York, N. Y. '28 Barrett, C. P 5338 Harper Ave., Chicago, 111. '28 Bayless, William S Russ Bldg., San Francisco, Cal. '28 Bean, Louis, H 60 E. 42nd St., New York, N. Y. '28 Beatty, Ross J Room 604, 6 N. Clark St., Chicago, III. '28 Benwell, Oswald F Hold Mags. '28 Beymer, Albert S., V.P., Keystone National Bank Pittsburgh, Pa. '28 Blumenthal, Hugo 44 Pine St., New York, N. Y. '28 Boettcher. Charles Ideal Cement Bldg., Denver, Colo. '28 Bowlus, Thomas H., Banker, Pres., Allen County State Bank Iola, Ran. '28 Brown, Colvin B Chamber of Commerce, Washington, D. C. '28 Burt, Maxwell Struthers Southern Pines, N. C. '28

Jan 1, 1936

By J. W. Harshbarger, E. L. Montgomery

The region of metallic ore deposits in northern Chile, southern Peru, western Bolivia, and northwestern Argentina occurs in arid zones at altitudes as high as 6 km (19,700 ft). Because surface water supplies are meager, new mines require unexploited sources of water. Prolific ground water aquifers occur in salar basins in this region of the Andean Highlands. Exploration water wells have been constructed and aquifer characteristics have been tested in eight salar basins. Results indicate ground water quality is good. Aquifer transmissivity and storage computed from results of pumping tests indicate maximum capacities of more than 170 L/sec (2700 gpm) for individual production water wells. Results of investigations conducted by the authors demonstrate that ground water reservoirs in the Andean Highlands comprise a source of large quantities of water for the mineral industry.

Jan 1, 1986

Albin, B. R Billings, Mont. '28 Amster, Nathan L 25 Broad St., New York, N. Y. '28 Bache, Jules S 42 Broadway, New York, N. Y. '28 Barrett, C. P 5338 Harper Ave., Chicago, 111. '28 Bayless, William S Russ Bldg., San Francisco, Cal. '28 Bean, Louis, H 60 E. 42nd St., New York, N. Y. '28 Beatty, Ross J Room 604, 6 N. Clark St., Chicago, III. '28 Benwell, Oswald F Hold Mags. '28 Beymer, Albert S., V.P., Keystone National Bank Pittsburgh, Pa. '28 Blumenthal, Hugo 44 Pine St., New York, N. Y. '28 Boettcher. Charles Ideal Cement Bldg., Denver, Colo. '28 Bowlus, Thomas H., Banker, Pres., Allen County State Bank Iola, Ran. '28 Brown, Colvin B Chamber of Commerce, Washington, D. C. '28 Burt, Maxwell Struthers Southern Pines, N. C. '28

Jan 1, 1934

By AIME AIME

THE many kinds of iron and steel may be grouped into two general classes. First, there are the common steels and cast irons, made in enormous tonnages each year and used for the construction of buildings, ships and bridges, for pipe, for reinforced concrete highways, for the so-called tin cans, and by the railroads and other industries for which a low cost material is suitable. Second, there are the alloy steels and alloy cast irons, which are alloys of the chemical element iron and one or more of a large number of special elements such as manganese, silicon, nickel, chromium, vanadium, tungsten, and molybdenum. Alloy steels and irons are more costly than the common grades but their higher cost is, for many applications, justified by their superior properties, leading to ultimate economies or other advantages. They may be harder, stronger, tougher, or more resistant to rusting than the common varieties, and so are extensively used for tools, for ornamental work on buildings and in the automotive, aircraft, and other industries for, which the higher cost is compensated for by the higher quality.

Jan 1, 1933

By Archer E., Wheeler

COPPER operations in the Congo mean the operations of the Union Miniere du Haut Katanga, because there are no other copper industries there. There is a mine at Bwana M'Kubwa, a little way to the South, in Rhodesia, which has been operated on a small scale, and-another farther south, the Falcon mine, but in quite a different section of the country. This Bwana M'Kubwa mine has recently been reorganized financially and the Minerals Separation interests have taken an extensive share in it, so that it may come into operation. The Union Miniere's operations are in Katanga, the most southeastern province of the Belgian Congo, and the company's concession is in the southeastern part of that province. The usual route for going into the country is by way of Cape Town, thence over the South African Railways through Kimberly and Mafe- king to Bulawayo, then by the Beira, Mashonland and Rhodesia Railways to the Rhodesia-Congo border, passing Victoria Falls on the way, and finally by the Belgian road, the Chemin de Fer du Katanga, to Elisa- bethville, the African headquarters of the company. From Cape Town to the border it is about 2150 mi. and from the border to Elisabethville about 158 mi., making a little over 2300 mi. from Cape Town, by rail.

Jan 1, 1924

By SIDNEY ROLLE

ACURSORY glance through the literature on the subject reveals that the ablest minds in the land are devoting themselves to the great question of labor, of which employment is one of the fundamentals. Volumes have been written and the end is not in sight. Employment management is today about in the position that efficiency was 15 years ago. During the early days of the war, and perhaps for a year or so before, labor was plentiful. As the war progressed and Europe drew on us for munitions, employers began to compete with one another for', all, classes of labor. Labor was difficult to obtain, wages rose, the labor turnover increased, and employers began to install employment departments, welfare plans, and all sorts of schemes, but the labor efficiency dropped. As the war progressed, greater and greater production was demanded. New factors were introduced each day. The government, labor unions, industrial councils, all tended, it seemed, to make the situation almost intolerable. Wages rose to fantastic heights, the cost of living rose higher and higher, and the efficiency dropped still further.

Jan 1, 1921