Search Documents

By Howard R. Keil

PRIOR to World War II, approximately 500 tons per day, or one-third of the ore being shipped to the Golden Cycle Mill at Colorado Springs, Colo., from the Cripple Creek district, was being treated in the flotation plant. The remaining 1000 tons, along with the flotation concentrates, received the usual roasting and cyanide treatment. Since it was not possible to make a disposable tailing on the general run of Cripple Creek ores by flotation alone, it was necessary to treat the flotation tailings by cyanidation, along with the roasted ore. By this treatment, an overall economical tailing could be made. The gold ores from the Cripple Creek district are the highly siliceous sulphotellurides with approximately 3 pct total sulphides. In the lower grade ores most of the values are found in very finely disseminated pyrite. In some of the higher grade ores the tellurides, calaverite and sylvanite, can be recognized. After several years of floating Cripple Creek gold ores, having a very low mineral content, it was concluded that this type of ore required a Type of flotation machine that would give a rather violent aeration and agitation. This action produced a fairly deep froth column which contained not only the free mineral, principally pyrite, but also most of the middling product; this was most essential in producing a low grade tailing by flotation alone that could be discarded to waste. After investigating most of the current types of flotation machines, it was decided to convert to the Fagergren type. During World War II, the flotation plant was modified to handle lead and zinc ores. The treatment of these ores was carried on until April 1946. At this time the flotation plant was again reconverted to handle the Cripple Creek ores. SELECTING ORES FOR FLOTATION During the period of reconversion a considerable amount of experimental work was carried on in the laboratory to determine if a disposable tailing could be made by flotation alone, on certain selected ores from the Cripple Creek district. It was found that most of the dump ores and a few of the low grade mine ores could be treated by this method with very satisfactory results. After the preliminary test work in the laboratory, it was decided to carry on further work on a plant-size scale to see if similar results could be obtained. On April 15, 1946, a part of the plant was put into operation as a pilot plant. The various ores that had been found suitable for treatment by this method in the laboratory, were run through the pilot plant at the rate of 200 tons per day for a period of several months. Results were so encouraging that it was decided to put the plant in full-scale operation. Since that time plant capacity has been increased from 500 to 1000 tons per day. This has been done not by the installation of more machinery but by (I) crush-

Jan 1, 1947

By D. J. Freeh, W. E. Horst, R. C. Kellner

This paper is concerned with the description of grinding characteristics in a batch grinding system. A mathematical model was developed and used for simulating the system on an analog computer. A general equation describing the change of selected size fractions with respect to time is presented. The empirical verification of the model is discussed. In order to understand the performance of a grinding system, it would be desirable to have a mathematical description of the system's behavior. The development of a mathematical model to describe the performance of a batch dry-grinding operation was investigated. This is the first step toward reaching the objective of a practical mathematical description of a grinding system that could be employed for process control and optimization of a simple or complex grinding circuit. Although this article is concerned only with batch grinding performance, experimental work is being conducted to extend the model to continuous grinding systems. BASIC PROCESS CONSIDERATIONS In a paper dealing with the probability theory of wet ball milling, Roberts1 correlated the rate of change of oversize material, C, with energy input, E, as follows where the energy input is expressed in power/unit mass and k is a constant for each particle size. Experimental grinding studies were made by Bowdish2 to extend the previous work of Roberts. The work of Bowdish also showed that the rate of breaking of oversize particles in a ball mill is proportional to the concentration of oversize particles present. He further demonstrated that breaking of oversize particles is proportional to the surface area of the balls used for grinding. Rate equations were presented and it was concluded that grinding could be considered as a first order phenomenon according to the rate equation [2] di which is in accordance with Eq. 1. In Eq. 2, the effect of ball area is included in the constant k,. Other rate equations were reported to show the effect of a change in ball area and removal of fines during grinding. Correlation studies made by Arbiter and BhranY indicate a first-order rate equation for quartz; however, their data showed less than first-order rates existed for some of the other materials evaluated. More recently Kelsall4 has shown that the rate of breakage of any narrow size range of quartz could be described by a first-order rate equation. Several other investigators5-7 have described grinding behavior in terms of rate equations or kinetics. In general, the rate equations have been described for each particle size; however, the interactions between sizes and the overall relationships that exist have not been considered, at least not in the form of solving a group of simultaneous differential equations. Extensive work has been conducted by various investigators using a probabilistic approach which has expanded stein's' earlier work. Selection and breakage matrices are incorporated in the probabilistic model as contrasted with the deterministic method presented here. A batch grinding operation may be considered as an unsteady-state process from the standpoint that the conditions within the mill are a function of time. Therefore, a plot of mass fraction of the i-th size versus time would give a set of curves as shown in Fig. 1. In these curves X , represents the mass fraction of large size material, X2 intermediate size, and X3 small size material. An examination of these curves shows a strong similarity to the curves that would be obtained from a chemical reaction of the type9 A?B?C, [3] where A would be comparable to the largest size material being broken to an intermediate size, 3, and

Jan 1, 1968

By G. H. Tausch, T. A. Huber

Very encouraging progress has been made ill the develop-ment of the permanent-type well completion which decreases considerable the cost of completions and workovers and aid-in the acquisition of reliable reservoir information at low cost. Completion and remedial operations are performed with tool,; which pass through the well tubing. Perforating and plug-hack operations can be done with the tubing in place and do not require pipe-handling equipment. Because of the many advantages afforded by this method, development work is going forward in anticipation of ultimately being able 10 use it to perform all usual well completion and workover operations. Effort is also being directed to the development of a more permanent type of lift equipment suitable for use with the permanent-type well completion. INTRODUCTION The permanent-type well completion in one in which the tubing and well-head are set in place only once in the life of the well and the completion or remedial work is performed through the tubing with a tubing-type perforator. a retrievable tubing extension. and other wire-line tools. This new type completion has made possible the saving of one to two days' rig time in the completion of each of several hundred wells During the last two years, and use of equipment developed for this type of completion has resulted in a 75 per cent reduction in cost. of certain types of workovers. In addition. the more reliable indication of the commercial value of a reservoir and the more accurate general reservoir information made Possible promise to be of even greater value in oil recovery than the reduction of costs for completions and workovers Recently. several well.. were worked over by using the retrievable tubing extension suspended on a swab line to plug back with cement and then perforating a higher producing interval with the tubing-type perforator, thus opening the way for complete through-the-tubing workovers which may be performed without pipe-handling equipment or mud. Those items attendant to the use of pipe-handling equipment and mud. such as hoard matting rig substructure. and pits. were also eliminated. There are indications that the elimination of drilling mud during completion and workover operations will frequently give increased well productivity, as plugging of the perforation. will not occur. It ii now possible to perforate selectively small sections of the producing interval and to test a well through these sections prior to perforating more interval. The perforating of additional interval will not entail the costly operations of killing the well and pulling tubing, nor will the old or the new perforations be plugged. The productivity of .mall sections of a reservoir and the actual gas-oil or oil-water contacts may now be determined economically under flowing condition.. Selective completions can be made in this manner to delay gas and water problems and bring about maximum oil recovery. At the present time, gas lift appears to offer the greatest potentialities for artificial lift in the permanent-type well com"letion since it can provide full-open tubing to accommodate the through-the-tubing tools and it may be ultimately developed into a fairly permanent type of lift. With precent-day pas-lift equipment. valve or mandrel failure necessitates occacio11al removal of the tubing. thereby reducing to some extent the permanence of the completion. New gas-lift valves are now

Jan 1, 1953

By C. Allen Born

INTRODUCTION As the title of this paper suggests, the author does not believe that risk can be managed. Rather, the objective is to identify the risk which will be present in a given venture and assess the level of that risk which is acceptable. More often than not, the risk which is present is subject to little or no modification. After identifying and measuring the risk a corporation will decide to accept it and proceed in such a way that it will be less exposed, or it will decide not to proceed at all. The exercise for a corporation is different only in degree from everyday judgements made by average people in average situations. However, that word "degree" means that it is considerably more complex on the corporate level. There is good reason for the additional complexity of corporate risk evaluation. The variables influencing a company's decision can be more numerous and the penalties for miscalculation much greater than those normally encountered by an individual. It should be understood that no analysis of risk, certainly not one as brief as the following, can do more than touch on some of the high points. Before examining the sorts of risk which affect the development and operation of specific mines, let us consider the broader aspect of the term with which mining companies, and all other business corporations, must deal. Companies must determine their long-term objectives and strategies within the context of a constantly changing world. To plot their direction they must attempt to read the future by seeking answers to questions such as: How will society evolve? Which businesses will thrive? In which of these should we place our emphasis? If a company hopes to be around five or ten years from now it must make the attempt to answer such questions in order to judge the impact of changing patterns in the evolving business environment. Information is available to allow the lessons of the past to be projected on the future. We have data on birth rates, economic booms and busts, patterns of conflict within and between nations, drought and other forces of nature as well as individual events which cannot be predicted, but which over time, do seem to occur in regular cycles. Ultimately the question "where will we be and what will we be doing a decade from now?" must be answered by one or more senior people with responsibility for the company's future. The compilation and interpretation of hard data by competent support staff, can only be used up to a certain point in determining future corporate strategy since there will be alternative possible futures and a high degree of risk will always remain. At this point those elusive qualities of experience, instinct, and - "gut feeling" - become important factors in choosing a long-term corporate direction. The goals of a company have a significant bearing on its attitude towards risk. This in turn dictates the "hurdle rate of return on investment" which a project decision-maker will require. The hurdle rate is the minimum-discount-percentage-rate applied to forecast cash flows to give a present value of zero to the All-Equity-Funded Investor. The feasibility study for a project is a fundamental tool in the management of risk. An experienced team has an established and well-understood set of ground rules for the preparation and assembly of a feasibility study. The necessary degree of conservation is built in at all levels of study data and, if the project is technically feasible, the hurdle rate becomes a catch-all measure of risk in a base-case project cash flow.

Jan 1, 1985

By F. W. Bloecher

DETERMINATION of the surface area of finely divided minerals is of interest to mineral engineers engaged in flotation, comminution, and de-watering studies. In the industrial minerals field, many materials are classified as to fineness according to their specific surface (surface area per unit weight). A method of surface area determination has been tested and used in the Richards Mineral Engineering Laboratories at M.I.T. It involves low temperature krypton adsorption measurements using the technique described by Beebe.' During the past fifteen years a number of new surface measurement techniques have been developed. Those that are broadly applicable to materials dealt with by mineral engineers include the permeability method in which a gas or liquid is passed through the sample, and the low temperature gas adsorption methods first described by Brunauer, Emmett, and Teller."" Efforts to make surface determinations from size distribution curves have long been attempted"."." but because of the uncertainty of sub-sieve size distribution and inaccuracies in screen analyses, the method is at best only a rough approximation. The most widely used gas adsorption method utilizes nitrogen gas." Nitrogen adsorption, however, is not particularly suited as a tool for most mineral engineers because the method is not applicable for surface determinations on coarse materials, that is, materials coarser than approximately 150 to 200-mesh. Other gases have been used in mineral engineering studies, particularly ethane."' lo The use of ethane gas, however, involves .a technique that is too sensitive for most mineral engineering work. The permeability method of surface area determination has the disadvantage of not being sensitive enough to detect the surface represented by minute cracks, the so-called internal surface of a particle. The low temperature krypton adsorption method described by Beebe1 utilizes apparatus and techniques that are essentially the same as those used in the ethane adsorption method."1° The surface area is calculated by the B.E.T. method."-' The krypton adsorption technique is particularly suited to the needs of the mineral engineer because: (1) The method can be used for making surface area measurements of rather coarse materials (35 to 48-mesh), as well as extremely fine materials, such as clays or colloidal slimes with specific surface that might be as high as 20 to 30 mb er g. (2) The use of krypton gas offers the advantage of low saturation pressures (2-3 mm) at the conveniently obtained liquid nitrogen temperature. Therefore the krypton vacuum system need not be designed to measure or withstand internal gas, pressures above one atmosphere as is the case with the nitrogen gas method. (3) The krypton technique offers the safety feature of employing liquid nitrogen, as contrasted to the ethane technique in which liquid oxygen is required. Furthermore, ethane vapor pressure at liquid oxygen temperatures is low (about 10 microns), and a high sensitivity McLeod gage is required for pressure readings. (4) The measurement technique with krypton gas is much simpler and faster, and the apparatus is less elaborate than that required with either nitrogen or ethane gases. Apparatus A krypton surface measurement apparatus like that used at M.I.T. is shown in Fig. 1. It is constructed of pyrex glass. A vacuum is maintained by two mercury diffusion pumps in series backed by a mechanical vacuum pump."' The vacuum thermocouple gage is used for checking the vacuum within the system. This type of gage is quite sensitive down to a pressure of 1 micron of mercury," but may be used to indicate pressures much lower than that

Jan 1, 1952

By Peter A. Allen

INTRODUCTION Lac Minerals Ltd., a significant North American producer of gold and other metals for over three decades, recently completed the financing for its third discovery in an eight year period. From 1975 to 1982, three important gold deposits in Quebec and Ontario: namely Bousquet, Doyon and Hemlo, were located and tested by company geologists. When current development plans are complete, Lac will have injected $400 million into these deposits. A discussion of these projects and their financing reveals some extraordinary challenges faced by top mining management. Responses to these challenges developed by Lac management may interest executives planning to proceed with new North American gold or base metal mines. MINE DE BOUSQUET In 1976, we explored a property containing a large low grade surface gold deposit. The geologial setting was exciting and we tested recent rethinking about the volcanigenic genesis of gold and base metal occurrences. These ideas helped pus to persist in drilling a nearby conductor and 600,000 ton, 0.22 ounce/ton orebody was outlined. With gold at $Cdn.150 per ounce the feasibility was approved and work started February 1978. Availability of a company custom mill 35 miles away reduced our immediate capital needs to $8.5 million. First of all, understanding the geological significance of results at Bousquet was critical. Mine and surface exploration geologists at Lac are continually and closely working together to better understand the nature of gold deposits in the Shield. This management emphasis on both pure and mine geology meant that a much larger ore reserve could confidently be predicted. (A proposal to quickly develop and ship the ore to a nearby company mine was discarded.) Instead of designing just for the initial plan of 500 tons per day we therefore included headframe, shaft and hoisting capacity for 1,700 tons and provided a compartment for future shaft deepening. These prebuilt additions were welcomed within two years. The type of collaboration whereby surface and mine geologists make study and field projects of each other's problems sets the foundation for this predictive ability. At Lac, the traditional responsibility for and supervision of the mine geologist by the mine manager is modified by this collaboration. This adds interest and scope to the geologist's work and lets him think beyond production requirements. Besides such management considerations, dedicated, professional geologists with integrity and lots of practical experience are needed to plan successful developments like Bousquet. Second, projecting future bullion revenue was critical and our experience selling production for future delivery gave us a way to ensure that loan repayment at term would not be jeopardized by falling metal prices. Output from a single mine is often reduced or curtailed for numerous reasons, so "selling forward" is done best and with least risk by companies like Lac with more than one or two producing locations for that metal. At first, a forward marketing program was considered unwise, speculative and unorthodox by analysts and other producers. Declining markets in the early 1980s prolonged gold project capital recoveries however, and critics were better able to appreciate the usefulness of such a tool. The notion that gold miners shouldn't sell forward is rooted in the belief that long-run gold prices will rise as modern social theory implementation in democracies inevitably erodes currency values. Selling against this trend goes against this industry belief or "ethic" and is at odds with the company shareholder who expects the gold price to rise not fall. Nonetheless, an efficient tool is available to the gold producer (not to most other metal producers) to quickly disengage from adverse price trends or to lock in spot prices instantaneously for two years or more of profits. Gold had recently retreated from U.S.$200 to $104 and now had reversed to $150. Lac had been forced to close several of its producers during the late 1960s because central bank-controlled

Jan 1, 1985

By W. M. Reilly, Martin E. True, O&apos

A technique, equipment, and a compound have been developed and field tested for sealing tubing joint thread leaks without removing the tubing from the well. This eliminates the necessity of killing the well with possible damage to the producing formation, which could result if it were exposed to drilling mud. A thread sealing compound, developed and tested in the laboratory, is introduced into the tubing and squeezed into the joint to eliminate the leak. A high percentage of successful field applications have eflected an appreciable cost reduction in repairing leaking tubing strings in East Texas and in the Louisiana Gulf Coast area. INTRODUCTION In producing oil and gas wells the industry has been plagued with a never ending problem of tubing connection leakage. This situation is becoming increasingly more significant as more gas wells are placed on production and as higher pressures are encountered at greater depths of current drilling. Substantial progress has been made in minimizing thread leaks by careful handling and cleaning of joints and by the use of improved sealing compounds in combination with controlled makeup. But even with the use of the best known methods and sealing materials during initial makeup, occasional leaks through tubing joint threads appear inevitable. In some instances, tubing joints in high-pressure gas wells have been found to leak gas at relatively less pressure than that at which the tubing had been tested satisfactorily using liquid. Many expedients have been employed to prevent the physical replacement of tubing when leaks have developed. Perhaps the most commonly used is the sodium silicate treatment in which the solution is lubricated into the tubing to form a crystalline plug in the leak. Generally, any benefit realized is of a temporary nature. In addition to field studies on handling and makeup of tubing, extensive laboratory work has been undertaken on the development and testing of thread dopes.' Also, substantial effort has been devoted to testing tubing joints using high-pressure gas as a pressure medium.' The results of this work have emphasized that tubing joints are susceptible to occasional leaks, especially when subjected to relatively high differential pressures. To cope with the problem of leaking connections, an extensive investigation was undertaken to devise means of sealing leaks without removing the tubing from the well and without reducing the inside diameter of the tubing. The purpose of this paper is to present a technique, together with the associated equipment and compound, which have been developed for effecting a seal of leaking tubing in place. DISCUSSION Work was initiated simultaneously on two ventures: (1) to develop a satisfactory leak sealing compound and (2) to develop tools necessary to find the leak and place the compound. Leak Sealing Compound In the development of a sealing compound, tests were conducted on those compounds commercially available which include: (1) conventional thread lubricants, (2) thermo-setting resins and (3) other materials which held promise of effecting a seal. Although none proved completely satisfactory in their available form, two commercial compounds proved nearly equally effective in sealing leaks during laboratory tests after proportioned quantities of graded silica had been added. Field usage has indicated that the preferred compound is one prepared of an aluminum-stearate base thinned to the proper constituency and carrying a mixture of fine mesh graphite and graded silica. The compound developed by Humble Oil & Refining Co. is designated as Tubing Thread Leak Sealant 800. Placement Tools and Technique In developing tools to detect joint leaks and to place the sealing compound, work was done initially on wireline equipment. Preliminary designs were completed of a tool somewhat on the order of a pressure bomb to test individual joints with gas at high pressure to determine if the joint was leaking. An entirely different tool equipped with opposed packers was intended for placement of the sealing compound at high pressures in each leaking joint. The application of these tools

Jan 1, 1958

By Donald E. Garrett

The processing of brines from Searles Lake, California, yields one of the world's largest supplies of borax and boron chemicals, second probably only to the massive deposit at Boron, California. Two companies produce from this deposit, the American Potash & Chemical Corp. and the West End Chemical Co., a division of the Stauffer Chemical Co. Two processes are employed in recovering borax from the brines; one is used by both companies and consists of carbonating the brine to form sodium bicarbonate, removing this, and then cooling the liquor to crystallize a crop of borax. Only American Potash uses the second process, evaporating the brine to concentrate it and remove (crystallize) much of its NaCl, Na2CO3, Na2SO4, and NaLi2PO4 content, quick cooling the remaining liquor to remove KCI, and then seeding the filtrate to remove borax. Both methods will be briefly described. Searles Lake is a large evaporite body formed during the most recent two Sierra Nevada ice stages, the Tahoe and the Tioga. Runoff waters from the Sierra Nevada Mountains collected in the large Owens Valley drainage basin and from there overflowed into the Indian Wells basin and then into Searles Lake. In each Lake, evaporation took place. To a large extent the Owens and Indian Wells lakes acted as settling basins, for much of the mud, and insoluble calcium and magnesium precipitates were deposited there. Recent volcanic activity in the mountains to the north and east of Owens Lake had scattered considerable mineral-rich volcanic ash and debris throughout the drainage area, and several hot springs were formed that contained boron and other salts. The present flow rate and concentration of several springs, and the known age of at least the Tioga zone, can fairly well account for all of the boron present in Owens and Searles Lakes.1 The tungsten content can be accounted for in a similar manner.2 Most of the salts thus originally present in the fresh water runoff-from ice, snow, and rain-accompanying these two ice stages were ultimately deposited in Searles Lake. During the Tahoe period, from 25 to 40 ft of massive, mixed salts were deposited, along with six interspersed layers of mud (four inches to two feet thick) representing comparatively brief interglacial periods. Before the final desiccation of the lake, from 10 to 14 ft of new mud was deposited, representing the Tioga stage. The crystals subsequently deposited were from 70 to 90 ft thick, and form the present lake surface. The extent of the salt body is about 34 square miles, of which 12 square miles are exposed salt; the remaining area is covered by recent alluvial deposits (chiefly mud). The present lake is generally dry on the surface but floods to a shallow depth following heavy rains. The crystal body of both zones consists of continuous clusters of salts, and the voids between crystals (about 45 pct of the total volume) are occupied by brine. The level of this brine never recedes more than several inches below the salt surface. The brine pumped to the plants for processing is generally saturated with all of the solid phases present in that area, and thus is a complex mixture containing about 35 pct solids (see Table 3). The brine composition varies somewhat at different areas of the lake and from upper to lower structures, so wells are drilled in the areas and to the depths desired. A casing is cemented in the hole to within a short distance from the bottom, and pumps with about 14-ft suctions are mounted on the casing to pump the brine into the plants. The evaporation process of the American Potash & Chemical Corp. treats upper structure brine, evaporating all of the water from

Jan 1, 1960

By Denton R. Wieland, Harvey T. Kennedy

The frequency of bubble formation is measured for oils from the East Texas field and the Slaughter field in cores from these fields. East Texas oil was also tested in a Slaughter core. The data checked previous results in that a definite supersatrtration may exist without the formation of bubb1es in periods of observation totaling 158 hours. Measured frequencies varied from zero at supersaturations below 14 psi to 3.1 bubbles/sec/ cu ft of rock at 40 psi supersaturation INTRODUCTION The formation of bubbles is essential in a solution gas-drive reservoir in the displacement of oil. In formations where the basic pore structure consists of fine pores or fractures connected to larger pores or crevices, bubble formation in the fine pores may be the most effective means by which the oil may be displaced, even if secondary methods are applied. The most efficient oil displacement would occur where at least one bubble would form in every pore. As the pressure decreased, the bubbles would expand, due to the gas diffusing into the bubbles, and displace the oil toward the lower pressure area around the wellbore. Kennedy and Olson' have shown that the total number of bubbles formed in a reservoir is primarily dependent upon the rate of pressure drop, the rate of diffusion of gas through oil, and surface area of the rock. The surface tension of the liquid and other characteristics of the rock may also exert an important effect, which would give a different frequency to different rocks and oils and various combinations of different rocks and oils. The purpose of this paper is to present frequency measurements on two rocks and two oils. A hydrocarbon liquid is at equilibrium with gas when it contains the maximum volume of gas in solution that it can have at the prevailing temperature and pressure. If the temperature is maintained constant and the pressure is reduced below the equilibrium pressure, the liquid is supersaturated to the extent of the difference in the two pressures until the gas comes out of solution as a free phase. As shown by previous work, and confirmed in the present investigation, the number of bubbles formed per second increases with an increase in supersaturation. Kennedy and Olson showed that a tenfold increase in the rate of pressure decline resulted in a tenfold increase in the number of bubbles formed per cubic foot of reservoir rock, e.g., for decline rates of 0.1, 1, and 10 psi/day, the number of bubbles formed per cubic foot would be 40, 400, and 4,000, respectively. For another hypothetical system, Stewart, Hunt, and Berry' estimated that for pressure declines of 0.1, 1, and 10 psi/day, the number of bubbles formed would be approximately 10, 100, and 1,000 cu ft of reservoir rock. Their value of bubbles formed is lower than given by Kennedy and Olson; however, the order of magnitude agreed satisfactorily. The rate of diffusion will also affect the number of bubbles formed. If the diffusion coefficient is high, the gas in solution in the oil surrounding a single bubble will tend to diffuse into the bubble rather than forming other bubbles. On the other hand, the formation of more bubbles will tend to occur if the diffusion coefficient is very low. In his thesis dated Aug., 1953, Wood" reports on the frequency of bubble formation in a system consisting of oil and rock from the Rangely field. In the present work, the apparatus of Wood was redesigned to allow greater precision, especially at low supersaturations, where bubble growth is slower, and detection is more difficult.

Jan 1, 1958

By A. M. Gaudin, C. S. Chang

Adsorption was measured for barium ion and laurate radical, using radioactively marked agents, over wide range of concentrations. Laurate adsorbed in absence of barium fails to float. With barium, flotation-effective laurate coating needs not exceed 5 pct of monolayer. Barium adsorption then is several fold larger. No barium laurate coating is obtained. IN general, fatty acids or their alkali salts do not cause clean quartz to float. However, the presence of multivalent ions, such as the alkaline-earth metal ions and heavy-metal ions, can activate quartz and thus make it respond to soap flotation. The mechanism of activation and soap flotation of quartz has been studied.'-' The problem was attacked by making flotation tests rather than by careful adsorption measurements on suspensions of ground quartz in solutions containing the activator and the collector. Attempts have been made to determine the adsorption of barium ion and calcium ion on quartz. The results have only qualitative value as the analytical methods were not adequately precise. Artificial radioactivity and progress in radioactivity detection have introduced a new analytical tool, which can have a sensitivity several orders of magnitude greater than that of other methods."-" In the experimental work described in this paper the radioactive tracers, barium 140 and carbon 14, were employed. Lauric acid was synthesized, having a radioactive carbon atom and was used with Ba" to study the adsorption of barium and laurate ions from aqueous solution on ground quartz. Flotation tests, using the vacuum flotation technique,' were run in conjunction with the adsorption experiments. The object of this investigation was to understand better the reaction mechanism of barium activation and soap flotation of quartz. Methods and Materials Quartz Sample Preparation: Lumps of hand-picked quartz, washed free of stains, were reduced in size to —20 mesh in laboratory crushers. The product was boiled in concentrated hydrochloric acid to remove the abraded iron. The cleaned product then was ground dry in a laboratory porcelain mill, using siliceous pebbles, to pass through a 200 mesh screen. The ground product was deslimed by sedimentation at 37 microns. This —200 mesh +400 mesh material was subjected again to boiling with concentrated hydrochloric acid, followed by washing with distilled water and further desliming. The cycle was repeated until no trace of iron could be detected in the wash liquor. During the final washing, the pH of the wash water was checked to insure the complete removal of the acid from the mineral. The quartz then was rinsed with conductivity water. The resulting product was dried in a drying oven and stored in mason jars. The impurities (spectrographic) were as follows: Al, 0.01 to 0.001 pct; Li, Mg, Mn, Na, each less than 0.001 pct; Fe and Cu not detected. The specific surface of the quartz sample was determined by the krypton gas adsorption method.' The average of two measurements was 881 sq cm per g. The calculated specific surface for 37/74-micron quartz particles, using a surface factor of 1.96; is 900 sq cm per g. This is in good agreement with the measured value of 881 sq cm per g. Beta-Counting Method: The radioactive isotope of barium used in the experimental work was barium 140. It has a sufficiently long half-life, 12.8 days, emits high-energy beta particles (up to 1.0

Jan 1, 1953

HARD as it is at any time to provide more than three million tons of coal each year for power plants, the task really gets rugged in the wintertime when the fuel freezes solid in the cars. At the Marysville plant of the Detroit Edison Co. the problem of unloading cars of frozen coal was severe because there was an unloader over only one of the two tracks in the coal unloading house. Moving downward by their own weight, with no driving force to aid them, the spuds of this old unloader were unable to break through the crust on a frozen coal car. 20,000 Lb Force To meet this problem, a new mechanical car unloader was installed over No. 2 track and placed in service in December 1947. It is a Kenney type unloader built by Heyl & Patterson, Inc. of Pittsburgh, Pa., a modification of equipment originally designed to unload iron ore cars. The major advantage of this unloader is the force with which it can drive the sharp spade on the end of its ram down through the pockets of a frozen coal car. The unloader consists of the following major units: 1. A traveling bridge structure. 2. A traveling trolley. 3. A retractable and oscillating ram. 4. The operators cab and controls. The bridge is provided with safety hooks to prevent its being lifted from the rails by the upwards push of the ram. The bridge will travel 190 fpm and has sufficient traction on its four wheels to move three loaded 70 ton cars. The trolley runs on tracks supported by the bridge girders and also has upper tracks to control the push from the ram. Two of the single-flange trolley wheels are driven by a one and a quarter hp dc motors equipped with magnetic brakes. The ram is raised and lowered by a 20 hp dc motor equipped with a magnetic brake. A full stroke of a little over 14 ft is given the ram through its rack and pinion drive and the spade can be pushed down into a loaded car with a force of about 20,000 lb. A 15 hp dc motor with a magnetic brake is applied to this drive and is able to swing the ram 45º either side of the vertical. The usual procedure in emptying a coal car is first to drive the sharp spade down through the coal until the pocket is opened and the coal starts to run out the hopper. When all the hoppers are open, the sweeping action of the ram and spade is used to move the remainder of the coal in the car over to the open hoppers. The travel of the trolley permits cleaning the sides of a coal car with the edges of the spade, using the sweeping motion of the ram. It is still necessary to clean out the corners of the car by hand. Final Clean-Out This unloader was a new development and there were improvements to be made before it was completely satisfactory, such as reduction in speed and conversion to ac drive motors. However, it helped at Marysville and unloaded many frozen cars that would have taken a lot of heating to thaw out enough for the old unloader to handle. The mechanical coal unloader described above was a considerable improvement but still left a job to be done by hand-the final cleaning out of the coal cars. The ram had the ability to open a hole through the hopper cars, but did not meet required unloading speed. To eliminate hand cleaning a car shakeout, manufactured by Hewitt Robins, Inc. was added to the installation. This equipment is used to clean the coal car out after the unloader has provided an

Jan 1, 1952

By A. D. Mutch

IT has long been known that there are wide variations in the thermo-electric potential of pyrite. In the last few years a study of this variation and other properties of pyrite was carried out at the University of Toronto by F. G. Smith on specimens of pyrite from many loyalities. As a result of these studies the pyrite geothermometer was developed by Professor Smith. The calibration of the pyrite geothermometer is based on the assumption that "crystals of any one electronically conducting mineral species deposited at a high temperature have a more positive thermoelectric potential than crystals deposited at a low temperature, and the thermo-electric potential varies continuously between any given limits of the temperature of deposition." The cause of the variation was postulated to be crystal discontinuities, such as lineage boundaries. As yet this postulated relationship has not been established as fact. On theoretical grounds it is indicated that the thermo-electric potential of pyrite or any other partial conductor is dependent upon a number of factors as well as the temperature of formation. For this and other reasons there is ground for doubt as to the validity of the relationship postulated above. To date a large number of readings have been made with the pyrite geothermometer which have been recorded in terms of the calibration of the instrument in degrees centigrade. So far most of the pyrite tested by this technique has been in association with gold ore. The values for the temperature of formation obtained in these tests appear to be reasonable and, in relation to geological problems, to vary in the right sense. Determinations on some specimens not in association with gold ore have given readings that appear to be much too high, taking into account the probable maximum temperature of the host rock. To sum up, although many determinations made with the pyrite geothermometer appear to give reasonable values for the temperature of formation of the pyrite, there are at the same time other readings which seem anomalous. On the basis of an examination of available results of work with the pyrite geothermometer, two problems must be considered: 1—the validity of the calibration of the pyrite geothermometer; and 2— the nature of the distribution of the thermo-electric potentials of pyrite in relation to the specific problems that have been examined. In this paper the academic problem relating to the validity of the calibration of the pyrite geothermometer will not be discussed. Instead, the variations of thermo-electric potential of pyrite in association with gold veins will be discussed with regard to specific examinations. The first of these two examinations deals with the distribution of thermo-electric potentials of pyrite in association with a gold vein and was carried out in the McIntyre Porcupine Mine, Schumacher, Ont., in the summer of 1949 as part of a study with this technique. The second problem deals with variations of thermo-electric potential of pyrite in gold ore specimens from all over the world. The specimens used in this study were part of the private collection of Frank Ebbutt, geologist for Howe Sound Exploration Co. Results of Detailed and Reconnaissance Studies In discussion of the results of determinations made in these two studies the values of thermo-electric potential in millivolts will be used. It will be noted that in some of the diagrams the determinations are recorded in terms of pyrite geothermometer temperatures. Fig. 1 is a calibration chart relating pyrite geothermometer temperatures and thermoelectric potentials. A full discussion of the technique is given in the original paper by F. G. Smith.' Briefly, the determinations are made by placing two stainless steel probes, one hot and the other cold, against the surface of the pyrite crystal being tested. The thermoelectric potential that is developed is read with a null-point potentiometer that is calibrated in what

Jan 1, 1953

By M. Cohen, P. E. Beaubien, D. Caplan

Addition of 1 pct Mn to Fe-26 CY ca/(ses a12 increase in scaling rate at 870° and 1090°C. Whereas only the rhombohedral oxide, formrs on tire manganese-free alloy, with manganese present major amounts of the spinel .Mn0 . Pro-duced through which diffusion is more rapid. At 1090°C the scale formed OH Mn is highly, irregular due to blistering and sintering, This is a second cause of faster oxidation Since much of the blistered oxide does not participate as part of the protective layer. The oxide phases that form at different times depend on the degree to which the surface metal has become depleted, in manganese by preferential oxidation. PREVIOUS work has demonstrated that the oxide scales formed on chromium steels at high temperature consist of both spinel and rhombohedra1 phases and may contain considerably more manganese, especially in the spinel phase, than is present initially in the alloy.' It has further been observed that a binary Fe-26 Cr alloy scaled less rapidly than an equivalent commercial steel and formed no spinel.' However, it is not established if manganese in chromium alloys actually promotes formation of spinel nor if it affects oxidation resistance. It seemed expedient to try to evaluate the specific effect of manganese by oxidizing an Fe-26 Cr alloy containing a small manganese addition under the same experimental conditions as used for the manganese-free alloy.' EXPERIMENTAL Table I shows the composition in weight percent of the Fe-26 Cr-1 Mn alloy and of the Fe-26 Cr alloy used as reference. The alloy with manganese was prepared from the vacuum-melted Fe-26 Cr alloy by remelting in vacuum with the proper manganese addition. The ingot was rolled to strip and specimens 1.1 by 0.035 by 5 cm and 1.1 by 0.5 by 4 cm cut out or machined. As previously described2 the specimens were smoothed by abrading through 600-grit Sic paper, electropolished in acetic-perchloric acid (20 to 1) to remove 10 p of metal, annealed at 1100°C in 20 torr of purified argon, and electropolished to remove a further 10 p of metal. They were then either rinsed in water and methanol and blotted dry or immediately etched for 45 sec in deoxy-genated 4 N HC1 under cathodic polarization at 10 pa per sq cm. Oxidation runs were carried out in a vertical tube furnace in a flow of purified oxygen at 1 atm while the weight increase was recorded continuously on a* automatic balance.3 Alter 98 hr at 870.C or 20 hr at 1090"C the specimens were removed to flowing argon and observed microscopically for evidence of spalling as they cooled. Subsequently they were examined by X-ray diffraction, the oxides analyzed chemically, and metallographic cross settions prepared. RESULTS Figs. 1 and 2 show the oxidation curves of Fe-26 Cr-1 Mn at 870' and 1090C. The Fe-26 Cr reference runs are shown as dashed curves. Experimental details of the six runs are included in Table 11. The first 20 hr of run 1 is repeated in Fig. 2 to show the effect of temperature. At 8'70°C the weight gain for Fe-Cr-Mn is about twice that of Fe-Cr (curve 1 vs curve 2, Fig. 1). Both alloys show regular oxidation curves. On parabolic coordinates (right-hand scale of Fig. 1) the

Jan 1, 1965

By J. J. Gilman

RECENT experiments have shown that the mar-tensite reaction in a standard tool steel is influenced by the history of the reacting austenite. The martensite reaction proceeds to a given extent at a higher temperature in austenite formed from an annealed spheroidal structure than it does in austenite formed from tempered martensite: that is to say, a prequench lowers the temperature range of the martensite reaction in this steel. Furthermore, a prequench alters the appearance of the martensite as compared to martensite formed from "virgin" austenite. The steel used for this work was a manganese nondeforming tool steel of the following composition: C, 0.85 pct; Mn, 1.43; Si, 0.23; Ni, 0.12; Cr, 0.59; and W, 0.59. A piece from a rolled bar was forged to Vz in. sq and annealed to a spheroidal structure. Disks 1/8 in. thick were used in the experiments. Several sets of the specimens were prepared and austenitized in lead at 1475°F. Three sets were held at 1475°F for 15 min, quenched in water, and immediately reheated to 1475°F. After this quench the three sets were held for 5 min, 30 min, and 3 hr, respectively, at 1475°F and then the individual specimens in each set were quenched in molten baths to 325", 300°, and 275ºF, respectively, and held for 15 sec. Immediately after the quenching treatments? the specimens were tempered at 600°F for 30 sec to darken the martensite and then were quenched in water. The holding times were short enough to avoid isothermal transformation. Three other sets of specimens were given the same final quenching treatments as the first three, but they were austenitized at 1475°F for 20 min, 35 min, and 3 hr and 15 min, respectively, without an intermediate water quench. The two individual specimens from each set were quenched together in order to eliminate quenching errors. Several experiments were run in this way but only the six sets referred to are described in detail because they all yielded essentially the same results. By means of the stated heat treatments the martensite reaction was investigated for: 1—austenite formed from an annealed structure, and 2— austenite formed from tempered martensite. The martensite reactions of the two types of austenite differed significantly. This is shown by Figs. 1 and 2. Comparison of the photographs on the left in Figs. 1 and 2 with those on the right shows that less martensite was formed by a quench to a given temperature from prequenched austenite than from austenite formed from an annealed structure, that is, the prequench suppressed the martensite reaction. The effect was observed for specimens austenitized 20 min, 35 min, and 3 hr and 15 min. A comparison of Figs. 1 and 2 shows that the martensite reactions in both sets of specimens occurred at lower temperatures with increased austenitization time. This was caused by the increased dissolution of residual carbides with time at 1475°F. However, the difference in amount of martensite formed in prequenched austenite as compared to virgin austenite was approximately the same for all three austenitization times. One further observation should be noted. The needles of the martensite formed from virgin austenite are somewhat longer on the average and show less of a tendency to cluster than those of martensite formed from prequenched austenite. This causes the martensite on the right in Figs. 1 and 2 to have a more acicular appearance than the martensite on the left. Since the sets of specimens used in this work were austenitized for identical total lengths of time and the effect of a prequench on the martensite reaction existed for specimens held at the austenitizing tem-

Jan 1, 1953

By A. T. Corey, C. H. Rathjens

INTRODUCTION Although the oil industry has been aware of the directional variability of permeability in porous rock, the directional variability of relative permeability has been largely ignored. Yet it is apparent that such an effect must be present in a system in which the distribution of oil and gas within the porous matrix is controlled by capillary forces. It is easy to visualize a rock composed of layers of fine and coarse material such that gas flow across the bedding planes would take place only after the average oil saturation had been reduced to a very low value. The fine layers, because of their greater capillarity, would remain saturated and act as barriers to the flow of gas after the coarse layers had been desaturated. Flow of gas parallel to the bedding planes would obviously take place at a much greater liquid saturation. Without more complete information concerning the geology of a reservoir than is generally available, it is not possible to predict exactly how such phenomena would affect the over-all performance of an oil field. It is possible, however, to predict qualitatively the effect of stratification on relative permeability measurements made on laboratory cores. In this investigation the effect of stratification was studied analytically by assuming that two porous materials with different capillary pressure-desaturation curves (but identical relative permeability curves) were in contact and in capillary equilibrium. As a qualitative check on the analytical results, cores having various degrees of visible stratification were used for relative permeability measurements made with fluids flowing both parallel and perpendicular to the bedding planes. A quantitative check was considered impractical because of the difficulty of devising models in which two materials of predetermined properties could be joined without the plane of contact becoming a discontinuity. THEORETICAL CONSIDERATIONS AND ASSUMPTIONS The assumption of capillary equilibrium in an oil-gas system implies that the difference in pressure between oil and gas is everywhere the same. This means that the curvature of the interfaces must be everywhere the same in order to satisfy the equation where PC is the pressure difference between phases, y the interfacial tension and r, and r2 are the major and minor radii of curvature. Depending on the pore size distribution of coarse and fine layers, the volumetric percentages of oil and gas in these layers will differ when equilibrium exists. The exact relationship can only be determined by obtaining the complete capillary pressure-desaturation curves for each of the porous materials in contact. It has been pointed out elsewhere' that the capillary pressure-desaturation curves of sedimentary porous materials can often be approximated by the relation where C is a constant and Soe is the effective saturation to oil based on a percentage of the pore volume effective to flow. In the same paper it was indicated that, as a first approximation, the values of oil relative permeability are given by and the values of gas relative permeability by For this analysis Eqs. 2, 3, and 4 were assumed to apply to each of two components of a hypothetical porous rock in capillary equilibrium. It was also assumed that each of the components had a residual wetting phase saturation of 20 per cent so that 80 per cent of the total pore volume was effective to flow. The permeability of the coarse stratum was taken as 100, and its displacement pressure was such that C in Eq. 2 had the numerical value of 1. The corresponding values for the fine stratum were 10 for the permeability and 10 for C. Units are not specified because they do not enter into the final results. The choice of the permeabilities and displacement pressure ratios was made to expedite the calculations. Any reasonable rock properties could have been chosen without changing the results qualitatively. Several arrangements of the two components were studied. Table 1 summarizes the resultant permeabilities obtained for four types of arrangement. RELATIVE PERMEABILITY CALCULATIONS The first step in the computation of relative permeability for the composite cores was the plotting of the capillary pressure-desaturation curves and the relative permeability curves for the individual components according to Eqs. 2, 3, and 4. At arbitrary

Jan 1, 1957

By W. H. Yarroll

This paper presents a general discussion of the utility of the statistical technique known as multiple correlation, and gives three specific examples of its application. The first demonstrates the most simple form, or straight-line, multiple correlation. The other two demonstrate multiple correlation analysis in best-fitting third-degree parabolas. With the increasing availability of digital computers, the method becomes entirely feasible where heretofore its use was impractical. The advantages of the method are discussed, and curves are presented which were developed by computerizing the regression equations developed in the examples. The method described in this paper is for use with complex systems, and the examples given are complex metallurgical systems. This subject falls under the general classification of cybernetics, which is defined' as "the science of control and communication, in the animal and the machine." Machine, in this case, can include chemical and physical processes which take place within machines and processing equipment of all kinds. The classical approach to scientific investigation has been the construction of simple models and the changing of variables one at a time. This method is wholly inadequate for obtaining useful information from the complex systems of modern technology including many of our flotation and hydrometallurgical processes. Cybernetics offers the method by which complex systems which have been implemented as an art in the past can now be analyzed with all the discipline of a science. Mathematical techniques for achieving multiple correlation analysis have decided advantages over some of the other statistical methods.2-4 Multiple correlation does not require a series of experiments that have been rigidly planned as do many of the other statistical methods. For this reason, it can be used effectively for interpretation of information from op- erating plants, where planned experiments are impractical, as well as for laboratory experiments. First-degree multiple correlation has been used for many years, and was useful, but limited to linear or nearly linear relationships. The technique described in this paper provides a method for analyzing systems which may be non-linear. This particular technique is multiple correlation analysis in best-fitting third-degree parabolas. It is quite possible that lack of reference to the technique has been due to the overwhelming mass of computations it requires even for relatively simple problems. With the advent of computers, however, its use has become entirely feasible. For the benefit of those who may not be familiar with the subject, it might be well to pause at this point to discuss multiple correlation analysis — what it is and what it achieves. To go back to the old familiar fitting of a set of points with a best-fitting straight line by the least squares procedure, it is conceded that this a good method where there is only one independent variable influencing the dependent variable under consideration, and providing that the relationship is linear. In most fields of investigation, however, there are usually a number of factors exerting important influence, and they frequently bear relationships with the dependent variable other than straight line. Under these conditions, it is easy to see how misleading a simple correlation study might be. Multiple correlation can be used for any number of variables. Within the experience of the writer, this technique has been used to establish regression equations for determination of carbon rate, burden permeability, and production rate on iron blast furnaces, production rate on open hearth steel furnaces, life of molds for steel ingots, rolled steel tensile strength and various defects in rolled products, the performance of ore dressing equipment, and optimization of extractive metallurgical process variables. The discovery of mathematical correlation does not prove, per se, true cause-and-effect relationship, but simply establishes a hypothesis. If the regression equation can be used to make successful predictions of what will happen with future arrays of independent variables, then one can feel reasonably assured that true cause-and-effect relationships have been discovered.

Jan 1, 1968

By W. G. Pfann

Under certain conditions, a molten zone can be made to move through a solid by impressing a stationary temperature gradient across the solid. This phenomenon can be utilized in fabricating semiconductive devices, growing single crystals, joining, boring fine holes in solids, measuring diffusivities in liquids, small scale alloying, and purification. Fundamentals and exemplary applications are outlined. ANEW aspect of the travel of a molten zone through a solid is considered in this paper. Whereas, in previously described zone melting techniques,'-' zones were usually caused to move by changing the position or temperature of a heat source, in the present technique a zone is made to move by impressing a temperature gradient across it. For example, a thin layer of molten A1-Si alloy, sandwiched between two silicon slabs having a temperature gradient normal to the layer, will travel through the hotter slab. One feature of temperature gradient zone melting, as this technique will be called here, is that zones of unusually small dimensions can be maintained. This leads to such diverse uses as have been listed in the abstract. In this paper fundamentals of the movement of a molten zone in a temperature gradient, and some practical applications thereof, are outlined. Assumptions The movement of a molten zone through a solid body of solvent substance in which a temperature gradient exists will be discussed. The length of the zone will be its dimension in the direction of motion. The direction of the temperature gradient will be toward the region of higher temperature. To be considered is a binary or higher order solute-solvent system in which the concentration of solute in the molten zone is sufficient to produce a lowering of the freezing temperature of the solvent which is at least of the order of the temperature range impressed on the charge. While we discuss primarily molten zones in a solid matrix, the principles are applicable to solid or vaporous zones in a solid matrix, a requirement being that the diffusivity in the zone be substantially greater than in the matrix. Diffusion of solute into the surrounding solid will be assumed negligible. In general, its presence will not basically alter the conclusions to be drawn. For illustration, a system represented by the partial constitutional diagram of Fig. la will be discussed, in which k, the distribution coefficient defined in the figure, is constant and less than unity. However, the technique is applicable to any solute- solvent system in which one component lowers the melting point of another component. Movement of a Molten Zone in a Temperature Gradient Consider, in the system AB of Fig. 1, where B is designated the solute and A the solvent, the effect of sandwiching a thin layer of solid B between blocks of solid A and placing the whole in a temperature gradient such that the temperature of the layer is above the lowest melting temperature of the system. Surrounded by an excess of A, the layer will dissolve A, becoming molten, and expand in length." As so- lution of A continues, at both interfaces, the mean solute concentration in the zone will move to the right in Fig. la, until at temperature T, the liquid at the cooler interface reaches the liquidus concentration C,. Solution of A thereupon ceases because the liquid T1 is saturated with A. The liquid at the hotter end of the zone, being at temperature T2, is not saturated with A at concentration C1. Hence solution of A continues there and concentration C2 is approached. A concentration gradient therefore is set up in the zone, causing A to diffuse toward the cool end and B toward the hot end. As a result, the liquid at the cool interface becomes supersaturated and a layer of crystalline A containing concentration kc, of B in solid solution freezes. Since a source of A

Jan 1, 1956

By J. T. Norton, J. G. McMullin

The ternary system of gold-silver-copper is characterized by a solid solubility gap and a two phase region in which copper-poor and silver-poor phases coexist. At about 30 pct gold, the two phases become mutually soluble at temperatures below the melting temperature. As the gold content is increased, the solubility temperature of the alloys decreases until at about 80 pct gold, the two phases are soluble down to the lowest temperature at which the alloys will recrystallize. Although the general form of the two phase region is known, its boundaries do not seem to have been investigated extensively. In an X ray diffraction study, Masing and Kloiberl have outlined the boundaries of this two phase field at 400 and 750°C. Using only microscopic techniques, Pickus and Pickus2 determined a vertical section of the ternary diagram showing the 14 kt alloys (58.3 pct gold). These two reports are riot in complete agreement. It has been shown3 that some of the ternary alloys are susceptible to age hardening and that the hardening is caused by the separation of a homogeneous alloy into two phases at the aging temperature. While the gold-copper binary system is an outstanding example of super lattice formation, Hultgren4 has shown that a few per cent of silver added to gold-copper destroys the tendency for ordering. Because of the age hardening possibilities of these alloys, it seemed advisable to investigate the boundaries of the two phase field more in detail using an X ray diffraction method, so as to permit a better understanding of the aging phenomena and enable predictions as to the behavior of other alloys to be made. This is especially true for the 18 kt alloys (75.0 pct Au) at the lower temperatures since they are known to exhibit age hardening. Twelve ternary alloys were prepared having the compositions shown in Table 1 and graphically in Fig 1. The gold used was fine gold bars supplied by Handy and Harmon. The silver was a bar of high purity silver from the U. S. Bureau of Standards. The copper was a bar of vacuum-treated, high conductivity copper from the National Research Corporation. The pure metals in the form of powder were weighed out in proper proportions and melted in graphite in a high frequency induction vacuum furnace. They were heated to 1100°C and slowly cooled. The ingots were then removed from the crucible, inverted, returned to the crucible and remelted. This remelting procedure was intended to reduce segregation in the ingots. After remelting, the ingots were checked for weight loss. The weight loss in each ten gram ingot was held to less than 25 mg. The remelted ingots were cold rolled and then given a homogenizing heat treatment of 16 hr at 760°C to remove any remaining segregation. Powder specimens were prepared by cutting the ingots with a fine file, one half the required amount of powder being taken from each end of the ingots. When the X ray diffraction pattern showed any difference in lattice constant between the ends of the ingot, the ingot was remelted and given an additional homogenization treatment. All powder samples were sealed in evacuated pyrex tubes for heat treatment. Ordinary pyrex proved satisfactory for temperatures up to 650°C but above that temperature it was necessary to use a special high temperature pyrex glass. Annealing at temperatures below 500°C was done in a salt bath whereas for temperatures of 500°C and above an electric muffle furnace was used. In both furnaces the temperature control was ± 5°C. In all annealing treatments samples of cold worked powder were placed in a furnace which was already at temperature. In this manner the specimens recrystallized directly to the equilibrium structure for that temperature. Time at temperature was selected so as to allow complete recrystallization, but very little grain growth. Specimens were quenched from the annealing temperatures by breaking the pyrex tubes in cold water. X ray diffraction photograms were made of all the heat treated powders using copper radiation and a Phragmen

Jan 1, 1950

By L. D. Jaffe

From the limited experimental data in the literature, preliminary values were derived for the thermal diffusivity of titanium alloys and for the quenching severity of various mediums used in heat treating them. The thermal diffusivity, under quenching conditions, was found to be approximately 0.006 sq in. per sec. The quenching severity H for brine is approximately 8, for water 4, for oil 0.9, for air 0.08, and for argon 0.02 in. -' The quenching severity of the Jominy-Boegehold end quench water jet against titanium alloys appeared effectively infinite. Using these results, graphs were prepared showing ideal round sizes and Jominy positions having cooled conditions equivalent to those at the center and surface of titanium alloy rounds, plates, and sheets quenched in various media. THE importance of proper quenching of steel parts has long been recognized, and much quantitative work has been done on the subject. Recently, it has become evident that for titanium alloys, too, the rate of cooling from high temperature is important in obtaining high strength and hardness. Maximum hardness and strength may not be attained in the as-quenched condition but rather after a subsequent tempering or aging treatment. Nevertheless, if cooling from temperatures near the ß transus is too slow, for the hardenability of the alloy used, a soft a-ß structure will be produced which will not harden on subsequent aging.'-" The quenching of parts of practical interest can usually be approximated by simple shapes, such as cylinders (rounds) and plates (or sheets) of various thickness and combinations of these. A standard that has been used extensively for comparison purposes is the center of an ideal round: a cylinder quenched in a medium that instantly cools its surface to room temperature." For steel, considerable practical use has been made of the Jominy-Boegehold end quench hardenability specimen,".' and its value for titanium alloys is becoming evident. It therefore appeared worthwhile to attempt comparison of cooling conditions in titanium alloy rounds and plates of various sizes quenched in various media with cooling conditions in ideal round and Jominy quenches. These comparisons are based upon measurements reported in the literature. Quenching Severity of Jominy Water Jet and of Brine As one starting point, there were available the data of Phillips and Tobin8 for positions on a Jominy specimen having the same hardness as the centers of round bars of various size quenched in 5 pct NaOH brine, shown in Table I. The Jominy speci- men is a round bar, normally 1 in. diam and 4 in. long, quenched by a water jet at one end and air cooled on the other surfaces.' After quenching, hardness is measured vs distance from the quenched end on longitudinal flats ground 0.015 to 0.10 in. deep. The data of Table I were based on a subsized specimen of 3/4 in. diam. Since the positions tested are close to the jet quenched end, cooling there may be taken as due solely to the jet, and air cooling can be neglected. These positions are then equivalent to various locations near one surface of an 8 in. plate jet quenched on both sides. Assuming that the thermal diffusivity is constant and that Newton's law of cooling holds, temperature vs time curves at corresponding positions in Jominy specimen and round bar then may be calculated for various assumed quenching severities of the water jet and of the brine. Cooling curves are generally taken to be metallurgically equivalent when they show the same time to reach a temperature halfway between the initial (heat treating) temperature and the final (quenching medium) temperature.5 On this basis, using Russell's tables,9 upplemented by heat flow tables derived in similar fashion by the author for positions near the surface of severely quenched plates, it was found that the experimentally observed equivalence, Table I, was best matched if the quenching severity H of the Jominy water jet was taken as infinite (H = co). This means that the jet quenched surface should be considered as instantly cooled to the temperature of the water

Jan 1, 1956

By A. D. Mutch

IT has long been known that there are wide variations in the thermo-electric potential of pyrite. In the last few years a study of this variation and other properties of pyrite was carried out at the University of Toronto by F. G. Smith on specimens of pyrite from many loyalities. As a result of these studies the pyrite geothermometer was developed by Professor Smith. The calibration of the pyrite geothermometer is based on the assumption that "crystals of any one electronically conducting mineral species deposited at a high temperature have a more positive thermoelectric potential than crystals deposited at a low temperature, and the thermo-electric potential varies continuously between any given limits of the temperature of deposition." The cause of the variation was postulated to be crystal discontinuities, such as lineage boundaries. As yet this postulated relationship has not been established as fact. On theoretical grounds it is indicated that the thermo-electric potential of pyrite or any other partial conductor is dependent upon a number of factors as well as the temperature of formation. For this and other reasons there is ground for doubt as to the validity of the relationship postulated above. To date a large number of readings have been made with the pyrite geothermometer which have been recorded in terms of the calibration of the instrument in degrees centigrade. So far most of the pyrite tested by this technique has been in association with gold ore. The values for the temperature of formation obtained in these tests appear to be reasonable and, in relation to geological problems, to vary in the right sense. Determinations on some specimens not in association with gold ore have given readings that appear to be much too high, taking into account the probable maximum temperature of the host rock. To sum up, although many determinations made with the pyrite geothermometer appear to give reasonable values for the temperature of formation of the pyrite, there are at the same time other readings which seem anomalous. On the basis of an examination of available results of work with the pyrite geothermometer, two problems must be considered: 1—the validity of the calibration of the pyrite geothermometer; and 2— the nature of the distribution of the thermo-electric potentials of pyrite in relation to the specific problems that have been examined. In this paper the academic problem relating to the validity of the calibration of the pyrite geothermometer will not be discussed. Instead, the variations of thermo-electric potential of pyrite in association with gold veins will be discussed with regard to specific examinations. The first of these two examinations deals with the distribution of thermo-electric potentials of pyrite in association with a gold vein and was carried out in the McIntyre Porcupine Mine, Schumacher, Ont., in the summer of 1949 as part of a study with this technique. The second problem deals with variations of thermo-electric potential of pyrite in gold ore specimens from all over the world. The specimens used in this study were part of the private collection of Frank Ebbutt, geologist for Howe Sound Exploration Co. Results of Detailed and Reconnaissance Studies In discussion of the results of determinations made in these two studies the values of thermo-electric potential in millivolts will be used. It will be noted that in some of the diagrams the determinations are recorded in terms of pyrite geothermometer temperatures. Fig. 1 is a calibration chart relating pyrite geothermometer temperatures and thermoelectric potentials. A full discussion of the technique is given in the original paper by F. G. Smith.' Briefly, the determinations are made by placing two stainless steel probes, one hot and the other cold, against the surface of the pyrite crystal being tested. The thermoelectric potential that is developed is read with a null-point potentiometer that is calibrated in what

Jan 1, 1953