Search Documents

By G. W. Tuffnell, S. Floreen

Three Fe-18 pet Ni-base ternary alloys cortaining carbon, molybdenum, or cobalt were aged to pgroduce hardening by carbides, Ni3Mo, or ordering, respectively. Each alloy was tested in rotating-beam fatigue tests after hardening to 195 ksi ultim.ate tensile strength. The fatigue properties of three alloys soere essentially identical. The results suggest that tlze fatigae strength of an igron-base alloy should depend primarily upon the tensile strength, and not iipon the hardening mecaanisrn. THE fatigue strengths of many steels have been found to be directly related to their ultimate tensile strengths. For ultimate strengths below 200 ksi, the fatigue endurance limit at 107 to 10' cycles is approximately half the ultimate strength. Essen- tially all of the steels that have been tested, however, have been hardened by carbon. Thus it is not certain whether the relationship between fatigue and ultimate strengths is a general one that applies for other types of hardening in steels, or whether it applies only for the particular method of hardening by carbon. The recent developments of the martensitic precipitation-hardened stainless steels and the marag-ing steels have shown that it is possible to achieve high strengths in iron-base alloys by other hardening mechanisms than that due to carbon. Therefore, it is now possible to compare the fatigue properties of several iron alloys having the same ultimate strengths but hardened by different mechanisms. For the present study a binary Fe-18 pct Ni martensite was selected as a base material. This particular matrix composition has been found to have deformation characteristics very similar to pure iron.' Three ternary alloys were prepared by adding either 0.23 wt pct C, 5 wt pct Mo, or 20 wt pct Co to this base composition. After suitable heat

Jan 1, 1965

By Charles H. White

Methods in colorimetry are based on the assumption that the intensity of the' color of a definite volume .of solution is directly proportional to the quantity of the color-producing substance present. In the preparation and examination of colored solutions there are three ways in which the depth of color may be varied. These variables are : (1) the quantity of' the coloring matter; (2) the quantity of the solvent, or the dilution ; and (3) the thickness or depth of that portion of the solution examined. With these three variables as a basis, three general methods in colorimetry have been devised, all of which have been used in the determination of carbon in steel. In the first method, the quantity of the solution is kept the same for both the unknown steel and the standard, and the sections compared are of equal thickness, while the quantity of the standard is varied until the color obtained is of the same intensity as that produced by a definite quantity of the unknown steel. In laboratories where this method is used there is prepared and kept for permanent use a series of solutions with varying amounts of the standard, representing the percentages of carbon from the lowest to the highest demanded in that laboratory. These standard solutions are kept in bottles or test-tubes of equal diameter, and are arranged in series from the faintest to the most intense color, so that it is a simple matter to find the place of the unknown steel in the series, when the solution is of a definite volume and is contained in a tube of the same diameter as the standard tubes. In the second method, equal quantities of the standard and of the unknown steel are dissolved, the standard is diluted to a definite volume, and the solution of the unknown steel is di-

Jan 1, 1907

By R. Raring, W. J. Harris, J. A. Rinebolt

G. W. Geil (National Bureau of Standards, Washington, D. C.)—The authors state that the degree of accuracy realized in the experimental determination of a, is likely rather low. This inaccuracy is attributed to the difficulty in reading the load of the tension machine at the instant of fracture of the test bars. I believe there is another factor which may have added considerably to the inaccuracy in the determination of a,, namely, the determination of 8,. Fracture of a cylindrical tensile specimen of a ductile metal tested in tension at room temperature is generally initiated at the axis and rapidly propagates radially to the periphery of the necked section. During the propagation of the fracture, the metal at the rim of the minimum cross-section extends longitudinally and contracts radially. Thus values of 81, based on diameter measurements made after complete fracture of the specimens do not necessarily represent the strain at the initial fracture." Data obtained at the National Bureau of Standards with a 0.3 pct C steel in the condition as-quenched from 1575°F and tempered at 1000°F for 1 hr and tested in tension at room temperature indicated a considerable "rim effect" and as shown in Fig. 13, resulted in an apparent increase in Sf from 0.90 to 0.98. As the fracture strain of this steel is approximately equal to those of the steels reported by the authors, it seems probable that a similar "rim effect" may have added to the inaccuracies in the reported values of Si and accompanying values of El. R. Raring (authors' reply)—The authors are grateful to Mr. Geil for having called attention to a possible source of uncertainty in the determination of fracture stress, and they are in agreement with the principles upon which his discussion is based.

Jan 1, 1952

By D. L. Wood

INTERNAL oxidation of alloys has been investigated by Rhinesl,2 and by Meijering and Druy-vesteyn. Rhines showed that dilute Cu-A1 alloys can be internally oxidized without forming an external scale by annealing in an oxygen partial pressure equal to the decomposition pressure of Cu2O. The oxygen is supplied at the outside surface at a rate sufficient to maintain saturation of the surface with respect to oxygen. Oxygen diffuses inward and, at the interface between the subscale and the alloy, oxygen meets the solute and reacts to precipitate its

Jan 1, 1957

By G. T. Lineberry, L. Adler

Due to safety-imposed constraints on clearances for mobile bulk handling equipment, it is necessary to optimally select a unit based on speed and size. The unit cannot be both large and fast. Since output is proportional to both size (or capacity) and speed, the combination must be carefully examined to maximize output. A simple graphical procedure and a calculus-based solution are presented to accomplish this. While the procedure applies to all mobile bulk handlers, as an example of the solution technique, attention is focused on shuttle cars. Background Major variables To fully define a bulk handling problem, the conditions, equipment, and activities must be characterized. The conditions and activities, when lumped together, are termed "encumbered space," since they "act to impede motion, as with a burden" (Lineberry, 1979). The insertion of mobile bulk handling equipment into what is already a difficult set of conditions and activities compounds the state of encumbrance, as limited space is competed for by many normal and life support systems. Long (1972) recognized the effects of design criteria, including road width, on haulage vehicle speed and, therefore, on production. Velocity-clearance curves Velocity-clearance curves are either available or can be constructed in the field. A preliminary set of curves for average conditions and activities is shown in Fig. 1, where clearances are only for the side of the vehicle (Lineberry and Adler, 1984). These curves set the safe speed limits for a vehicle operating at given clearances, under given conditions and activities. When feasible, velocity-clearance curves should be constructed through field measurement and observation. Curve construction should also consider haulway roughness, distances, and operator skill, as well as loading and dumping characteristics. It should be noted that haulage capacity determination is a total systems problem, not one just dependent on velocity and clearances. Production requirements and company capabilities also influence capacity determination.

Jan 1, 1986

By H. F. Yancey

THE jig may be termed the standard coal-washing machine. Although exact figures on the relative tonnages of coal treated by the various coal-cleaning processes are not available, it is known that a large part of all the coal given special cleaning treatment is handled by jigs. This wide use of the jig warrants a special study of its performance. In this paper are presented the results of an analysis of work done by a three-compartment jig in treating bituminous coal from the Thick Freeport bed in Allegheny County, Pa. Certain systems of washing coal require sizing before washing, while others treat unsized coal. The prevailing practice, however, for the preparation of coking coal from the more easily washed coal is to treat an unsized or natural feed at about -1 in. size and smaller. Under such conditions, the minimum size of particle that is beneficiated has long been and is still a matter of discussion and conjecture. In a careful laboratory investigation Jüngst1 concluded that the practical limit of settling of fine coal is reached at from 0.02 to 0.008 in. On the other hand, Hancock2 has found that single-compartment jigs, used in preparing coal for the domestic market, usually allow most of the heavy (refuse) particles smaller than 1/4 in. to go into the washed coal. He also states that it is impossible with the ordinary coal jig to make any noticeable improvement in the quality of the coal finer than 20 mesh (about 1/30 in.). Because of its importance in coal cleaning, the work described in this paper was undertaken for the purpose of obtaining information on this subject, as a part of the general coal beneficiation program being carried out by the Bureau of Mines.

Jan 4, 1925

By Frank Firmstone

IN the summer of 1881 we were forced to break up and remove the large mass of iron which had accumulated under No. 2 furnace at Glendon, in order to prepare the foundations of the new furnace which has taken its place. We used "Atlas" powder, drilling the holes with a pair of Rand drills. These worked very well when the iron was at all uniform in hardness; but this was not often the case; and it frequently happened that the holes were hopelessly blocked when but little over a foot deep. Good tamping became, therefore very important. The common method of tamping is certainly very dangerous when there is a percussion cap in the hole, and has, no doubt, caused many of the accidents attributed directly to high explosives. We found an excellent and safe method by using plaster of Paris, mixed to the proper consistency and ponred into the holes as soon as they were loaded. Clean dry sand was mixed with the plaster to reduce the quantity needed. With proper attention the tamping would set in a few minutes, and little or no more time was required than for tamping in the ordinary way. We used a "magneto" machine (Laflin and Rand) to fire the holes; and an additiollal advantage in the plan was that any risk of cutting the exploder-wires in tamping was avoided. We found it worth while to load holes not over 13 inches deep in a block 3 or 4 feet thick since the bottom of the hole was enlarged by each shot so that the next time it could be loaded more heavily, and three or four shots in this way often did as much good as a new hole twice the depth, to drill which might have taken ten or twelve hours. The rise in temperature when boiled plaster solidifies is not sufficient to ignite the exploders, as we found by repeated trials before using it in a loaded hole.

Jan 1, 1884

By Charles Hawes

WHEN sulfur is encountered in objectionable amounts, it is regarded as the most trouble-some element for the mine operator to control. It exists in two conditions in iron ores, as sulfide in iron pyrites and as sulfate in gypsum and barite. The sulfate radical (SO,) may also be linked to one or more of the several other elements found in the iron ore compound. The only dependable method for the de-termination of sulfur, particularly when found in the insoluble residue, has been the so-called fusion method. This is a long and tedious process involving several hours for its completion. In looking for a more rapid method which would be .applicable to all iron ores, the writer investigated the work of M. Groger1 who in 1881 showed that by heating pyrite with iron out of contact with air, the pyrite is reduced to iron sulfide and from the latter all of the sulfur will be given off as hydrogen sulfide gas on treat-ment with hydrochloric acid. FeS2 + Fe = 2 FeS FeS + 2 HCl = FeC12 + H2S In 1891 F. P. Treadwell2 not only confirmed the results of M. Groger but also found that iron powder would reduce to sulfide the sulfate radical of any substance, including barite, if not found in excessive quantities. The writer found this to be true and developed a method, in cooperation with F. J. Baker, chief chemist, mining department, of the Cleveland-Cliffs Iron Co., Ishpeming, Mich., for the determination of sulfur in iron ores which is not only very rapid but also accurate. Pure iron ore powder, reduced by hydrogen, gave good results but was found to be very slow in reacting. A high silicon iron with a low sulfur content of 0.012 per cent was found to be. much more active than the pure iron and gave excellent results.

Jan 11, 1927

By R. R. Kimpel, L. G. Austin

An equation is derived describing fragment size for single fracture of brittle solids. It contains the equations of earlier workers as special or approximate cases and, in addition, is capable of describing coarse distributions in which a few large particles are produced on fracture. The equation can be fitted well to single fracture experiments where over-breakage is avoided. In 1956 Broadbent and callcottl described a method of analyzing the unit operation of grinding, applicable to homogeneous breakage of brittle materials. In essence, the grinding process was split into two parts: 1) the fractional amount of a given size which is selected for grinding per unit time, 2) the size-weight distribution of the fragments produced by breakage of this certain size (primary breakage distribution function). The theory was formulated using matrix algebra. They attempted an experimental verification of the theory using an assumed primary breakage distribution but the results were not very satisfactory. Austin and Gardner2 showed that this assumed distribution was widely different from experimental values and that it led to the poor agreement of predicted size-weight distributions with experiment found by Broadbent and Callcott. In addition, Austin and Gardner2,3,4 reformulated the original approach in terms of differential equations of grinding and demonstrated that the approach led to a very satisfactory description of the grinding process, providing that the descriptive parameters were measured experimentally. Recent work5 has substantiated these findings and the distribution functions of several materials ground under different conditions in different mills have been determined experimentally. The fraction underweight versus size used by

Jan 1, 1965

By G. C. Waterman, W. E. Hawes

Mr. Grieves' paper on "Shaft Sinking Today --A Boring Business Tomorrow" in the Dec. 1981 issue of MINING ENGINEERING is an excellent description of recent improvements in speed and costs of shaft sinking. However, shaft boring techniques are not a recent development. In 1935-36, the Idaho Maryland Co. (gold), Grass Valley, CA, bored the vertical 1.5-m-diam Idaho No. 2 ventilation and supply shaft to a depth of 346 m. The equipment was designed and perfected by Branner Newsome and was, I believe, described in "Transactions." Pickands Mather later bored a 1.8-m-diam shaft to a depth of about 305 m using Newsome's design. The Idaho No. 2 shaft cut through hard gabbro, diabase dikes, soft serpentine, very incompetent ankeritized serpentine and a strong fault zone. The completed shaft did not require timber support; the fault zone was cemented. Equipment consisted of a rotating 1.5-m or 3-m core barrel with a slotted bottom which cut a 76-mm kerf. The cutting agent was chilled steel shot introduced into the slot as needed. The driving mechanism and core barrel were lowered into the shaft, the former secured to the wall and the inshaft "engineer" operated the motors which controlled core barrel rpm and advance. After an advance of 1.5-3 m the equipment was lifted out of the shaft, a half(?) stick of powder cut off the drilled core, and it was hoisted to the surface with a cable attached to an eye bolt at the tope of the core. A "shift" consisted of three men: hoistman, equipment operator (down the shaft), and a surface laborer. Advance was variable as equipment and techniques were perfected. Near the end of the job advance was, as I remember, 1.5-3 m per shift. Costs were, as I recall, about $115/m. Up to 4 m cores were lifted out in one piece and swung to the dump by a stiff leg derrick. The Newsome equipment was relatively inexpensive to build and operate and his method should be (more than?) competetive with the methods described by Grieves.

Jan 1, 1983

By B. T. Brady

Rock mechanics, like all engineering disciplines, must have a theoretical foundation. The subject of this chapter is the formulation of analytical methods that may aid in the rational design and determination of the stability of engineering structures in competent brittle rock materials. By an engineering structure in rock, we mean any (1) excavated sub- surface opening, (2) open surface structure, or (3) system of openings in rock that is virtually self-supporting-that is, not requiring artificial systems to carry structural stresses. One factor necessary for designing or evaluating a structure's stability is knowledge of the material's mechanical properties, such as stress-strain behavior and fracturing characteristics. The composition of most structural materials such as metals and concrete is uniform and reproducible to the degree that their mechanical properties in service are nearly the same as those measured in the laboratory. Consequently, a rational design can be made on the basis of published mechanical property values. The same equivalence does not exist for rock materials for two reasons: (1) the composition of even the most common rock types is highly variable, and (2) the problem of the size effect is present. Mechanical property tests not conducted at a scale that includes these effects in normal proportion will not be representive of the in-situ rock mass. Of course, the alternative is to perform the test in-situ. Comparatively few mechanical property tests have been performed in-situ because of the physical limitations of test equipment and the prohibitive cost. The current procedure is to design a structure based on small-scale laboratory measurements, with a safety factor usually determined by the experience of the design engineer. While this procedure is somewhat unsatisfactory, laboratory measurements can and do provide a useful basis for the initial design.

Jan 1, 1970

By L. S. Panyity

THE State of Ohio is among the pioneers in the production of oil and gas. Numerous anticlinals, such as the Macksburg, Cow Run and Newport, have been thoroughly developed, and the pools found in connection with them are quite in accord with the structural theory. Numerous oil and gas pools found in the Berea sand, however, demand a different explanation. The study of these pools belongs to the sub-surface geologist, as it is possible to understand the factors controlling "off-structure" accumulations only after a careful study of well records. By carefully analyzing the various 'conditions over a large territory, it is possible to understand the otherwise meaningless mass of data that one may have at hand, and put it into tangible shape, from which various conclusions may be drawn. The territory here discussed includes Belmont, Guernsey, Muskingum, Noble, Monroe, Morgan, Washington, Athens and Meigs counties, containing the majority of the prolific oil and gas pools of the Carboniferous system in southeastern Ohio. The general dip of the strata is to the southeast, the entire territory lying on the northwestern flank of the Appalachian geosyncline. The best known oil- and gas-producing horizon in the territory is the Berea sand, which lies near the lower part of the Mississippian, with the Sunburry shales (the coffee-shales of the driller) above, and the Bedford shales below it. The Bedford is underlain by the thick Ohio shales. The Ohio and Bedford contact is considered to be the dividing line between the Carboniferous and Devonian systems. The Berea is one of the most persistent of recognizable oil and gas horizons; its outcrop has always been found in its expected place, and it has always been penetrated whenever the drill went deep enough. It is not expected, however, even of the most uniform formations, that no lithological variations should occur, and the Berea is no exception. Nevertheless, there appears to be a certain regularity in its variation, the main features of which directly affect the accumulation of petroleum.

Jan 8, 1918

By J. D. Doherty

A. R. POWELL*—Mr. Doherty has outlined in a most thorough manner valid arguments for the development of an industry in this country making syn. thetic liquid fuels from coal. No thoughtful person will dispute the statement that it is essential to carry on fundamental and applied research and acquire engineering "know-how" by the erection and operation of two or three large plants in the near future. Considerations of national security indicate that this should be done, irrespective of any temporary present surplus of natural petroleum. It is the belief of the discusser and of many others interested in coal technology that our energy picture of the future will include an increasing utilization of coal directly, without any conversion to liquid fuel, as a source of energy. A fact that is sometimes forgotten is that petroleum fuels have often been cheaper than coal in many locations and over long periods of time, and this price factor has been of great importance in expanding the use of petroleum fuels at the expense of coal. Synthetic liquid fuel made from coal must necessarily be several times as costly as the coal from which it is made, and this fact alone will have a profound effect on the future energy pattern of our country. This complete change in the economic relationship between solid and liquid fuels will lead to the substitution of coal itself for many uses now supplied by the relatively cheap petroleum fuels. From the standpoint of conservation of our natural resources, the substitution of coal itself for liquid fuels wherever possible when the age of synthetic liquid fuel arrives is also logical. At least 50 pct of the energy of coal is lost during conversion to liquid fuel. Nor is this com-pensated for by a higher utilization effi-ciency of the liquid fuel in most cases. For example, modern steam-boiler plants can operate at equal fuel efficiencies with either coal or fuel oil.

Jan 1, 1950

By O. L. Kowalke

THE measurement and control of temperatures have assumed positions of great importance in many industries. The manufacturers of byproduct coke and carbureted water gas find that proper temperature control helps to produce a better product and economizes in the use of raw materials. In the manufacture of glass, enameled ware, brass, and high-temperature refractories, temperature control is now regarded as being coordinate in importance with the control of materials used. To control such processes as malleablizing cast iron, and hardening, tempering, and annealing of steel in a manner to meet exacting market requirements has, within recent years, involved the installation of large and expensive pyrometer equipments. In many of these installations, it was necessary not merely to measure but also to record the temperatures over a period of time and thus obtain a record of the entire heat treatment and an effective check on the workmen in charge. In view of the importance of temperature measurement and control in such a wide variety of industries and the necessity for proper supervision of the installation and operation of the outfits, the following questions may be pertinent: What instruction is offered by the engineering colleges and what departments in the colleges are responsible therefor? The latest available catalogs of ten prominent engineering colleges east of the Mississippi River showed courses in high-temperature measurements given by the departments of physics. These courses, in general, were described as comprising classroom and laboratory instruction in the theory of high-temperature measurements, together with exercises in the calibration of the various devices used. In some cases it was stated that consideration would be given, in the courses, to the practical applications in the industries. In only one. college was the course required of all engineering students; in most colleges it was optional; in a few colleges, it was required only of certain groups. In colleges offering a course in metallurgical engineering, instruction in pyrometry was always given in connection with metallurgical laboratory work. The students in ceramic,

Jan 8, 1919

By Andrew A. Blair

It is now well known that certain pig-irons give a considerably smaller percentage of sulphur when determined by evolution-methods than when determined by oxidation-methods. The most striking examplcs of such irons are those made either wholly or in large part from New Jersey magnetites containing more or less titanium. It is never safe to use an evolution-method on such iron; for it is quite common that the sulphur result by evolution is only one-half or even one-third as great as that obtained by oxidation. For this reason, evolution-methods should be discarded, except in the analysis of pig-irons known to contain the sulphur in a state of combination from which it is evolved as sulphuretted hydrogen on treatment with hydrochloric acid. A good example of an iron containing, in the residue, sulphur insoluble in hydrochloric acid having come to our attention, it was determined to try to isolate a suspected insoluble sulphide. A large piece of high-silicon gray-forge iron was accordingly selected as the most promising material to work on. This piece was dissolved slowly, through several months, in dilute hydrochloric acid, aided by the electric current, yielding a soft graphitic residue. The object of dissolving a mass of iron, instead of drillings, was to prevent the crushing, by the drill, of any insoluble crystalline compound that might be present. The first step in the preparation was to break up the graphitic material and put it through bolting-cloth of 157 meshes to the linear inch. This was done by crushing the mass under the fingers on the bolting-cloth fastened over the top of a beaker, while a stream of water from a wash-bottle washed the finer portions through the cloth. The suspended matter was allowed to settle. It was then transferred to a platinum

Jan 1, 1902

By John W. Tieman

Coal is a term applied to vegetable matter which, through geological processes of heat and pressure, has had both its physical and chemical properties changed. Because its chemical composition is variable, geologists classify coal as a rock rather than a mineral. Peat represents the initial stages in the development of coal, although not classified as coal itself. PHYSICAL PROPERTIES OF COAL The physical properties are concerned with the characteristics of coal in its natural state, or prior to its end use as a fuel. For example, the hardness of coal determines the maintenance cost on coal handling equipment; the specific gravity of coal determines the coal preparation techniques used in a cleaning plant as well as the capacity of coal bins, boats and size of cargo, and other coal storage facilities. The physical properties are, of course, dependent upon the chemical constituents that make up coal, and thus all properties are interrelated. Specific Gravity The specific gravity of a body is the ratio of the weight of the body in air and the weight of an equal volume of water. The specific gravity of pure coal ranges between 1.25 and 1.70, generally increasing with rank. The most important use of this physical characteristic is the part that it plays in the cleaning of coal by wet wash methods. The basic principle on which these operate is that the specific gravity of coals differs from their associated impurities and that there is a relationship between the velocity of the fall of particles in water and their density. Since the specific gravity of slate is around 2.5 and pyrite is about 5.0, pyrite and slate will fall to the bottom of a container filled with water more rapidly than coal. If the water is given a pulsating motion by

Jan 1, 1973

By Bruce A. Kennedy

In recent months, public hearings held by the Senate Subcommittee on Minerals, Materials and Fuels on the Stillwater copper-nickel complex in Montana have been reviewed at great length in the press. Although the meetings were well managed by the Subcommittee and questioning was kept in line with the aim of the hearings-namely, how can re- sources be developed in a manner compatible with the preservation of the environment-it was alarming to read the apparently uninformed and questionable arguments presented by some witnesses who were attempting to prohibit mining in the area altogether. One spokesman even went so far as to urge that mining of the area be rejected be- cause, even if the mining operation did not pollute the areas, the effluent and waste produced by the people themselves could constitute a hazard to the environment and to themselves. This, of course, would be true to a point. However, if this or similar types of reasoning were used to reject mining of a large number of orebodies in the future, how is the United States going to meet its future mineral demands and what effect could this have on the economic strength of the country? Fall of the Roman Empire An interesting article in a recent issue of Time magazine came up with a new theory to explain the fall of the Roman Empire. Claire Patterson of CalTec, during a recent study of air pollution, investigated the historical worldwide distribution of lead. As lead was a by-product obtained from silver mining during historical times, he turned his attention to studying the production of silver during those eras. He discovered a very interesting fact-that, I unless the stock of metal is continually being replenished from the mines, accidental loss diminishes a country's stockpile of silver at a rapid rate, as much as 2 per cent per year. Patterson, a geochemist, theorized that with an accidental loss rate of 2 per cent per year, if the country's silver supply dried up, the entire existing stockpile could disappear in about a century.

Jan 1, 1971

By W. P. Haynes

No wildcat operations are recorded from France during the past year, and no new discoveries have been made. In northern Africa, in Morocco, some prospecting continued in the Gharb and Tselfat regions. Only very small production or shows were found. At the close of the year one cable-tool well (depth 400 meters) was drilling in the Tselfat district, and one rotary well in the Gharb. In Tunisia one well was drilling at Sloughia. Refinery building has been active under the new petroleum law, no less than six plants now being under construction. At Pechelbronn, it is estimated 130 wells were drilled, of which 73 wells, or 56 per cent, were productive. Total drilling was 45,000 m. One new Jurassic horizon was discovered. In the mining area approximately 17,500 m. of new gallery were driven. Production at Pechelbronn for the first nine months was as follows: From wells, 233,013 bbl.; from mines, 164,815 bb1.—a total estimated production for the year of 532,000 bbl. Production at Gabian was 3780 bbl. for the year. In Algeria production from Tliouanet was small, being estimated at 6510 bbl. This production is from Helvetian sands (Miocene) around a salt plug. Italy Production for the year was 211,500 bbl., an increase of 62 per cent over that of last year. Drilling to the extent of 97,000 ft. was done mainly by the A. G. I. P., the government company in the Province of Emilia. More locations are being tested in this area, where geophysical results have shown indications of buried uplifts. Oil has been encountered on two of these structures, at Fontevivo and Podenzano, but the wells have given trouble with salt water. The chief producer is the Societa Petrolifera Italiana at Salsomaggiore and Valezza. The production is from sand lenses at relatively shallow depths. New concessions of 2000 hectares were granted at several points in the Po Valley, and geophysical work is being carried on. The A. G. I. P. is working on a five-year program of exploration to test new areas.

Jan 1, 1933

By A. J. Weinig

The method described is a modification of Schutzenberger's whereby the solution in titrations and the standards are protected from the atmosphere by a layer of kerosene. Indigo-disulfonate is the indicator and sodium hydrosulfite the standard. The method is rapid and delicate. It has been tried on a variety of mill solutions and mill men have found the method of value. THE important part that dissolved oxygen plays in the cyanide treat-ment of gold and silver ores is commonly recognized by most metallurgists and mill men.. But heretofore there has been no simple method on which the mill man could rely for determining the amount of oxygen in the various mill solutions. A few methods are adaptable to the, laboratory, such as the gasometric1 determination by actually measuring the oxygen. Winkler's2 iodometric method, and Schutzenberger's3 method, which depends on the reducing action of sodium hyposulfite on a blue solution of indigo carmine; but these are not readily adaptable to the needs of the mill man and cannot be applied to cyanide solutions without modification. The gasometric method is the most accurate but it takes too long to complete a determination. White's' method (a colorimetric method that depends on the degree of coloration imparted to a solution of pyrogallic acid in the presence of caustic soda) although much more rapid than any of the methods named, often gives misleading results on account of grading of colors of different solutions, which nearly always contain various kinds of salts. The method herein described was devised for the use of the mill man, the aim being to develop a simple, practical, accurate method. It is a modification of the Schutzenberger method and depends on the reducing

Jan 8, 1924

By Daniel M. MacNeil, Raymond L. Presbrey, Carle R. Hayward

At the February, 1916, meeting of the Institute, a paper presented by Hayward and Raymond gave the results of a study on the effect of time in tempering medium-carbon steel, when the following conclusions were reached: It is not fair to consider the question settled when only three specimens were used for each treatment, but the results obtained indicate that for reheating quenched medium-carbon steel to temperatures below 500" it is only necessary to heat it through. Longer heating has little or no effect on the tensile strength, ductility, or hardness. At temperatures above 500°, increasing the time of treatment causes a slight falling off in hardness and tensile strength with a corresponding increase in ductility. In the discussion of the paper these conclusions were attacked and evidence was presented that seemed to throw doubt on their accuracy. The authors, however, showed that this evidence was based on high-carbon or alloy steels and no facts regarding medium-carbon steel were presented. During this study the heat treatment was carried out in a small electric resistance furnace. It held nine specimens, but when these were placed in the furnace the temperature was lowered to such an extent that 30 to 40 min. were required to reach the desired heat. The authors pointed to this as a weak point in the investigation and it seemed wise to supplement the research by work on similar steel but using a different method of heating. This has been done and the results are given in the present paper. The Rhode Island Tool Co. coöperated by furnishing the steel and turning the tensile specimens. The steel used in this investigation came in three bars 3/4 in. in diameter; analyses are as follows: Carbon. MaNGanese, Phosphorus, Sulfur Bar NUmber PeR Cent. Per Cent. Per Cent. Per Cent. 1 0.46 0.56 0.010 0.055 2 0.44 0.58 0.007 0.042 3 0.48 0.58 0.007 0.048

Jan 1, 1922