Search Documents

By Reginald S. Dean

Manganous oxide is readily soluble in concentrated ammonia solutions containing ammonium salts. Lixiviants of ammonia and ammonium carbamate permit ready extraction of manganese from reduced ores and the manganese in such solutions may be precipitated by heating to transform the carbamate to carbonate. THE widespread occurrence of manganese in low grade oxide and carbonate ores not amenable to mechanical concentration has led to extensive investigations of hydrometallurgical methods for producing a pure manganese compound suitable for further treatment. Manganese carbonate is the preferable compound. This product when fully crystalline and of not too fine crystal size is easily filtrable and stable in air. It can be converted to other compounds such as the oxides by heating in air or can be reacted with acids for producing salts. A useful hydrometallurgical process must produce relatively concentrated solutions that can be purified easily, reagents must be cyclically used, and heat requirements must be small. Neither the ammonium sulphate nor sulphur dioxide leaching processes that have been tested extensively fulfill these requirements. Other heretofore proposed processes have obvious limitations and have not been tried on a large scale. The present process is based on the discovery by the writer of a new group of aqueous manganese-ammonia complex solutions highly concentrated in ammonia, which permit rapid solution of manganous oxide to concentrations of 80 to 100 g Mn per liter and from which a fully crystalline, easily filtrable manganese carbonate is precipitated by the addition of carbon dioxide and partial ammonia removal. Although the process may be carried out with many ammonium salts, commercial advantages dictate the use of ammonium carbamate, which is obtained when CO2 is passed into concentrated aqueous solutions of ammonia. If the carbamate is used, the only reagents, ammonia and CO2, are volatile and may therefore be recovered from solutions and residues by heating, thus eliminating washing and extensive evaporation. Impurities are controlled easily as most metal oxides are either insoluble in the lixiviant or fail to precipitate with the manganese carbonate. Others are controlled by sulphide addition. The process has been tested extensively on a small scale on a wide variety of ores, including Three Kids, Artillery Peak, Cuyuna, and Chamberlain, as repre-

Jan 1, 1953

By John Sullivan

Resources for Freedom, a report by the President's Materials Policy Commission, commonly termed either the Paley report, after its chairman, or the PMPC report, was issued in June 1952. The data collecting and assembly work for its preparation were done in 1951. The statistical base in most cases was 1950. It reviewed our economy and predicted what it will be in 1975.* The bases for the predictions were given. Consideration was given not only to statistical data and trends but also to technological changes taking place and likely to take place in the ensuing 25 years that will affect our economy. The supply of raw materials was studied and predictions made as to the availability of supply and the sources in 1975. One of the industries covered was iron and steel. For the most part the report did not attempt to provide a curve showing annual growth for any industry or commodity. It contrasted 1950 with the probable status in 1975. Interpolation between these dates is difficult and the Commission did not intend that it be used for short interim intervals. It is possible in 1958 to show the actual changes from 1950. The magnitude of the changes illustrates the agreement with some interpolation of the Paley report. Statistical comparisons can be general only because the Commission did not postulate a linear change. A study of the iron and steel industry will show if the general predictions have been realized or if gross errors were made. This paper is concerned with such an analysis. It is concerned with the production and consumption of crude, not fabricated products. It attempts to bring various facets of technical and statistical information on the industry up to date.

Jan 8, 1959

By H. M. Chance

The present value of most coal properties resides largely in the cod remaining to be mined, which thus constitutes the most important asset. The object of this paper is to discuss methods commonly used in computing the value of minable coal. To distinguish clearly between such coal values and the values of other property, the several kinds of property values should be divided into classes; so as to avoid the unintentional omission of items of importance. Value op Coal Reserves Judicial decisions prescribe, and appraisers commonly accept, current sales value as the preferred means for determining the value of transferable property. With few exceptions a property is worth the sum that can be realized from its sale by a willing seller to a willing buyer, a sale in which compulsion urges neither party, and between whom there is no community of interest to fix a value; or it is worth at least as much as a responsible buyer will offer for it. Actual sales of like property or bids from responsible buyers for the property, or for substantially like property, are the best established methods for determining values. Only in the absence of such sales or bids can valuations by other methods be entertained, and only for reasons of weight can sales values be set aside. Valuation Based on Royalties Sales of coal in the ground, as customarily carried out through lease under royalty agreements, are therefore the most trustworthy means available for determining the value of coal reserves. The constantly rising value of high-grade coal in the United States can most readily be shown by the increasing royalties per ton that can be obtained for such coals under leasehold. The rising value of land containing such coal can also, of course, be proven by the price at which such properties are actually sold as compared with prices obtainable for lands containing coal of the same grade in the past. It is exceedingly difficult, however, to establish values by the prices paid for coal

Jan 1, 1927

By T. B. Brooks

THE iron ores of the Marquette region are mostly extracted in open excavations ; hence the process is more properly quarrying. Several attempts at underground work have been made, which have not, on the whole, been successful. The Edwards mine has been almost entirely wrought by candle-light. The slate ore pit, No. 1, of the New England mine, is now worked in the same way, as is also the Pioneer furnace pit of the Jackson mine. The Champion mine was opened systematically for underground work, with two levels, 60 feet apart, and three shafts at distances apart along the bed. of 200 feet; but this idea has been practically abandoned, the greater part of the ore in that mine being now taken out in open pits. Several other mines have occasionally worked underground stopes, but only temporarily; if such stopes could not be opened out to day-light, they have usually been abandoned. In brief, it may be said that no considerable amount of ore has as yet (1870).been extracted underground in the region, and of that so mined very little has been taken out at a profit; and I may add that it seems to be the belief of the most experienced mining men that this state of things will hold for some time to come for reasons which will appear. Nearly the same remarks may be applied to the mines of the Iron Mountain region, Missouri, the ores of which are very similar in character to those of Marquette. Some of the New York and New Jersey magnetic deposits are wrought open, but this is the exception, underground mining there being the rule. The following brief sketch of the geological structure of the Marquette deposits will indicate some advantages of the method of mining employed. The iron-bearing (Huronian) series of rocks, are stratified beds, the principal ore formation being overlaid by a quartzite, and underlaid by a diorite, or greenstone. This ore formation is made up, first, of pure ore ; second, of a mixed ore" (i. e., banded * A second part of this paper was read before the American Society of Civil Engineers. Both papers are embraced in Chapter IX, Part I, Vol. II, Geological Survey of Michigan.

Jan 1, 1873

By Reginald S. Dean

Manganous oxide is readily soluble in concentrated ammonia solutions containing ammonium salts. Lixiviants of ammonia and ammonium carbamate permit ready extraction of manganese from reduced ores and the manganese in such solutions may be precipitated by heating to transform the carbamate to carbonate. THE widespread occurrence of manganese in low grade oxide and carbonate ores not amenable to mechanical concentration has led to extensive investigations of hydrometallurgical methods for producing a pure manganese compound suitable for further treatment. Manganese carbonate is the preferable compound. This product when fully crystalline and of not too fine crystal size is easily filtrable and stable in air. It can be converted to other compounds such as the oxides by heating in air or can be reacted with acids for producing salts. A useful hydrometallurgical process must produce relatively concentrated solutions that can be purified easily, reagents must be cyclically used, and heat requirements must be small. Neither the ammonium sulphate nor sulphur dioxide leaching processes that have been tested extensively fulfill these requirements. Other heretofore proposed processes have obvious limitations and have not been tried on a large scale. The present process is based on the discovery by the writer of a new group of aqueous manganese-ammonia complex solutions highly concentrated in ammonia, which permit rapid solution of manganous oxide to concentrations of 80 to 100 g Mn per liter and from which a fully crystalline, easily filtrable manganese carbonate is precipitated by the addition of carbon dioxide and partial ammonia removal. Although the process may be carried out with many ammonium salts, commercial advantages dictate the use of ammonium carbamate, which is obtained when CO2 is passed into concentrated aqueous solutions of ammonia. If the carbamate is used, the only reagents, ammonia and CO2, are volatile and may therefore be recovered from solutions and residues by heating, thus eliminating washing and extensive evaporation. Impurities are controlled easily as most metal oxides are either insoluble in the lixiviant or fail to precipitate with the manganese carbonate. Others are controlled by sulphide addition. The process has been tested extensively on a small scale on a wide variety of ores, including Three Kids, Artillery Peak, Cuyuna, and Chamberlain, as repre-

Jan 1, 1953

By Ralph Hultgren, David W. Mitchell

MAGNESIUM alloys usually are superheated before casting in order to ensure fineness of grain. Superheat temperatures in common use range from 1600° to 1700°F while the casting temperature, which depends upon the mold shape, is usually 200° to 300°F lower. The process of superheating requires considerable time and seriously shortens the life of the iron pots used. Recently it has been reported' that if acetylene, carbon dioxide or natural gas is bubbled through molten electrolytic A.S.T.M. No. 4 alloy at 1400°F. for 5 min., grain refinement equivalent to that of superheating will take place. Addition of certain solids such as graphite or aluminum carbide accomplishes the same results.2 As will be shown in this paper, it is possible to achieve grain refinement in magnesium casting alloys at low temperatures by mechanical stirring of the molten metal for a short time. This process was developed in the course of research work, supervised by the War Metallurgy Committee under the "Restricted" Project NRC-550, for the Office of Production Research and Development of the War Production Board. This paper, based on that work, has been released for publication by the O.P.R.D. MATERIALS AND METHODS The alloys studied were the most common American sand-casting alloys designated as No. 4 and No. 17 by the American Society for Testing Materials. The magnesium used in these alloys was of both carbothermic3 and electrolytic4 origin. Chemical analyses supplied by the producers are shown in Table I. Each heat consisted of approximately 5 lb. of alloy melted in a Tercod crucible. It was refined by fluxing with Permanente No. 7* refining flux at 1300° to 1350°F. After cooling to 1200' to 1250°F., portions of approximately one pound each were ladled into iron crucibles contained in an electric furnace at about 1250°F. The molten metal was covered with Permanente No. 21† covering flux and then heated to the temperature to be investigated. Normally each of the four portions was given a different treatment. In a typical case one portion was stirred vigorously for 5 min., acetylene gas was passed through a second portion for 5 min., a third portion was superheated to 1600°F for 15 min., then cooled to casting temperature, and the fourth was held for 5 min. at the temperature of stirring or gassing without other treatment. Each portion was then cast into one-inch diameter cylinders in three "nonturbulent" molds of identical shape. One mold was made of cast iron and the other two of baked sand. The cast-iron mold and one of the baked sand molds were heated to 360°F., the other baked sand mold was at room temperature. The freezing times in these molds were

Jan 1, 1945

By Anthony Anable

THE definite trend to stricter specifications with respect to hydraulic concrete has become increasingly manifest in the last six years or so; but it remained for the vast reclamation projects of the Bureau of Recla-mation of the Department of the Interior of the last few years to focus attention on this trend, and to demonstrate how thousands of tons of concrete-making aggregates can be produced continuously and auto-matically with a control of fineness comparable with that obtained with small samples in well equipped private and governmental laboratories. Pioneer work in this direction was done, to be sure, by private com-panies, notably the Kaiser Paving Co. of San Francisco, prior to the present vast public works program. Then in 1931 came the first great aggregates-preparation plant of the Six Companies, Inc. to supply. construction materials for Boulder Dam' in Nevada, and now, in 1936, the aggregates plant of the Mason-Walsh-Atkinson-Kier Co., general con¬tractors on the Grand Coulee dam in Washington. At Boulder dam and to an even greater degree at Grand Coulee dam, sand production is recognized as probably the most important single element affecting the physical characteristics of the concrete. For in the construction of dams accurate grading of the fine aggregate has consider-able bearing on the attainment of a uniform and homogeneous concrete of a high degree of workability and placeability and, at the same time, combining high density and low cement content. Low cement content is of value not only from the standpoint of economy but also because the use of an unnecessarily rich concrete causes certain undesirable characteristics to develop. This paper will relate how at Grand Coulee dam methods that are more advanced than ever before are producing four sizes of gravel and a sand having a fineness modulus of 2.5-3.0. The design capacity is 1000 tons an hour. Significantly, the methods and equipment employed are broadly those that have been used for a generation in metallurgical mills for accurately sizing and grading both precious

Jan 1, 1936

By H. J. Rahilly

Mine fires, in the Butte district, have been a source of trouble and expense for the past thirty years, for while the actual fire area in most of the mines has been comparatively small, the handling of the gas has generally been a much larger problem than the actual putting out of the fire. The chief causes of these fires have been: Defective electrical equipment, incendiarism or carelessness, and spontaneous combustion. While fires from the first two causes have been numerous, they have generally been discovered and extinguished before they became very serious. Spontaneous combustion has been the cause of most of the large fires. Sufficient heat has been generated by ground movement, high rock temperatures, and decomposition to set fire to inflammable materials (tarred ropes, canvas, dry timber, manure, and hay) left in the gobs some years ago. Also, the heat resulting from the oxidation of the fine broken sulfide ore is sometimes sufficient to set fire to the timbers. In 1906, a fire was discovered on the 1100-ft. level of the Minnie Healy mine about 400 ft. (122 m.) west of the Minnie Healy shaft, which presumably originated, in one of the upper levels, from spontaneous combustion. The fire was walled off by concrete bulkheads and a pillar of ground 100 ft. (30 m.) thick was left below and mining resumed underneath. During subsequent operations, this pillar became cracked and broken and the fire passed into the new workings. It travelled downward and spread rapidly until, in 1917, it had become necessary to wall off portions of the Tramway, Leonard, and West Colusa mines on the 1300, 1400, 1500, 1600, 1800, 1900, and 2000-ft. levels, and the tops of the 2200-ft. raises were sealed. The fire area now consists roughly of a block 1000 by 1200 ft. and from the 600-ft. to the 2200-ft. level. This block is composed largely of a series of parallel northwest-southeast nearly vertical veins and stringers that form a large orebody, with no well-defined walls but badly fractured and faulted, and known locally as "horsetail ore." These veins, or orebodies, are mined by the square-set or the rill method.

Jan 1, 1923

By John Tyssowski

In 1925, Harry Howard Stout, then metallurgist for Phelps Dodge Corporation, while investigating the cleaning of cathode copper by various gases at elevated temperatures below the melting point of the metal, observed in the laboratory that particles of pure copper heated in a closed tube filled with hydrogen seemingly "stuck together." By further investigation he found that there was actual crystal growth across the boundaries of the particles of pure metal; in other words, there was a complete new crystal realignment and growth throughout the newly formed copper mass. It was coalescence, not adhesion; the several particles had become one unit. From this discovery has been developed the coalescence process, whereby copper of cathode purity is squirted out in semifabricated form from an extrusion press, by the application of about 3000 tons pressure on a 10-in. piston. Stout decided that cathode copper produced by electrolytic deposition was the logical source of the pure copper required for the coalescence process, but as there was no way of reducing the ordinary tough commercial cathodes to the small particles required he was confronted by a serious problem at the outset. Under his direction, this problem was solved by William H. Osborn and Harry Howard Stout, Jr. They developed the process and technique for producing cathode copper in brittle, friable form, and to them must be given the greater part of the credit for this phase of the development program as well as for that relating to the gas cleaning of the cathode particles. Concurrently, the three metallurgists worked on the problem of effecting a complete union of the cathode particles. Adequate washing was all that was needed to free the particles from electrolyte solution and slimes. A press was designed to produce briquettes of the proper porosity and density, and a method was devised of removing surface oxidation from the particles of cathode, by treatment in an atmosphere of deoxidizing gas at an elevated temperature. The temperature was determined at which the surface cleansing and preheating could be done in one operation, and for this a charging and preheating furnace in which there is maintained a positive pressure of deoxidizing gas atmosphere was designed. And finally, a method of feeding the heated briquettes of deoxidized cathode copper into an extrusion press without contamination from the air was evolved. For the final stage, a press was required because not only heat but pressure was required to obtain complete growth of the new crystals between the cathode particles as well as the elimination of all voids or non-coalesced areas. All essential stages of the process are protected by patents or patent applications in the United States and principal foreign countries, and the copper is produced on a commercial scale.

Jan 1, 1941

By E. A. Nichols

The purpose of this paper is to present a contour map that shows the geographical variation in geothermal gradients in the Mid-Continent and Gulf Coast oil fields. Introduction Frequently there arises the need for an estimation of the temperature to be expected at a predetermined depth in working with a wildcat or in deepening old production into 'Ones that are relatively unknown. The study of geothermal gradients in oil fields has been made previously by many investigators. One of the pioneers in this work was C. E. Van Orstrand,' who, as well as most of the other investigators, was primarily interested in the relation between temperature and depth in a given locality. Between 192r and 1929, American Petroleum Institute Research Project NO. 25 fostered a thorough study of earth temperatures.2 K. IV. French did some work in California, the results of which were published in 1939.3 In most of these studies, an attempt was made to correlate temperatures in a rather localized area. This paper will show the results of an attempt to correlate temperature gradients over rather large Portions of the Mid-Continent and Gulf Coast area. Method of Obtaining Data It has been found that for complete thermal equilibrium to be established in a well, the well must stand undisturbed for a period of several hours to several weeks, depending upon the way the well was produced prior to the shut-in period. The data in this paper were obtained in conjunction with running pressures in wells or in taking samples of reservoir fluid. Glass maximum recording thermometers were used in all but a few instances. The wells had been shut in from one hour up to I. or 12 days. Since the wells were normal producing wells, some of the shut-in times undoubtedly were insufficient for complete thermal equilibrium to have been established and the temperatures measured do not necessarily represent the true earth temperatures. They do represent the temperature conditions that will be encountered in a well that is producing oil. The data, therefore, can be useful in working with or in estimating the temperatures to be expected in producing reservoirs. In obtaining a thermal gradient by dividing the difference in temperature of the formation and the mean annual surface temperature by the depth of the formation, one is assuming the depth-temperature line to be straight. Depth-temperature curves are almost straight lines (Fig. I). However, on close examination of accurate data, a slight curvature usually is observed. Most wells yield curves with slopes increasing with increasing depth. These curves are believed to be from wells that are in and are underlain by sedimentary material. Some few curves have slopes that decrease with increasing depth. These curves are believed to be from wells that are underlain rather closely by granite or some other igneous rock. Most investigators

Jan 1, 1947

By E. A. Nichols

The purpose of this paper is to present a contour map that shows the geographical variation in geothermal gradients in the Mid-Continent and Gulf Coast oil fields. Introduction Frequently there arises the need for an estimation of the temperature to be expected at a predetermined depth in working with a wildcat or in deepening old production into 'Ones that are relatively unknown. The study of geothermal gradients in oil fields has been made previously by many investigators. One of the pioneers in this work was C. E. Van Orstrand,' who, as well as most of the other investigators, was primarily interested in the relation between temperature and depth in a given locality. Between 192r and 1929, American Petroleum Institute Research Project NO. 25 fostered a thorough study of earth temperatures.2 K. IV. French did some work in California, the results of which were published in 1939.3 In most of these studies, an attempt was made to correlate temperatures in a rather localized area. This paper will show the results of an attempt to correlate temperature gradients over rather large Portions of the Mid-Continent and Gulf Coast area. Method of Obtaining Data It has been found that for complete thermal equilibrium to be established in a well, the well must stand undisturbed for a period of several hours to several weeks, depending upon the way the well was produced prior to the shut-in period. The data in this paper were obtained in conjunction with running pressures in wells or in taking samples of reservoir fluid. Glass maximum recording thermometers were used in all but a few instances. The wells had been shut in from one hour up to I. or 12 days. Since the wells were normal producing wells, some of the shut-in times undoubtedly were insufficient for complete thermal equilibrium to have been established and the temperatures measured do not necessarily represent the true earth temperatures. They do represent the temperature conditions that will be encountered in a well that is producing oil. The data, therefore, can be useful in working with or in estimating the temperatures to be expected in producing reservoirs. In obtaining a thermal gradient by dividing the difference in temperature of the formation and the mean annual surface temperature by the depth of the formation, one is assuming the depth-temperature line to be straight. Depth-temperature curves are almost straight lines (Fig. I). However, on close examination of accurate data, a slight curvature usually is observed. Most wells yield curves with slopes increasing with increasing depth. These curves are believed to be from wells that are in and are underlain by sedimentary material. Some few curves have slopes that decrease with increasing depth. These curves are believed to be from wells that are underlain rather closely by granite or some other igneous rock. Most investigators

Jan 1, 1947

By M. D. Hassialis, A. F. Taggart

ark' observed some years ago that collector-coating reactions with xanthates and with fatty acids clearly follow paths parallel to those prescribed by the familiar mass-action law for reactions in dilute solutions. He proposed, therefore, the logical hypothesis that they are governed by the solubility-product principle. However, he went astray in the application of his proposal to collector coating by overlooking the fact that coating involves a heterogeneous reaction. A mistaken concept of the meaning of the word adsorption also entered. Wark thought that the concentration of metallic ion that must be used in setting up the solubility-product equation for the coating reaction was that which could be obtained by solution of the mineral. Since this is very low for sulphide ores, and since the amount of the collector ion necessary for coating produces an extremely low concentration, the resulting ion-concentration product, under conditions when coating occurs, is much lower than that which would indicate a saturated solution of the collector-coating compound. Hence he was forced to the position that the solubility product governing the coating is much smaller than the standard solubility product. To justify this position it was necessary to postulate a coating mechanism that did not obey the ordinary laws of chemical reaction. This Wark did by adopting the concept that adsorption is a property of matter, rather than merely a more or less ephemeral local concentration thereof. Thus he says (p. 142 of ref. I): "Adsorption is not a purely physical property of the solid surface, for the specific nature of the adsorbed molecule or ion is important." The result was that he destroyed the great potential utility of his postulate by tying it to this erroneous concept in the words (pp. 142, 143): "It will be obvious that the adsorption solubility product is less than the normal solubility product." The writers have found quantitatively in the case of galena and potassium ethyl xanthate, and semiquantitatively in the case of covellite and the same collector, that the coating reaction does follow the mass-action law to the extent that coating occurs when the ordinary solubility product of the coating compound is exceeded, and that coating does not take place under the reverse conditions. In the course of the investigation leading to the establishment of this fact it was necessary to work with xanthate concentrations so low (down to 0.0004 mg. per liter), that very long conditioning times, and bubble-contact times of as much as 16 hr. were necessary sometimes to follow the reactions. The results have led to some illuminating conclusions as to necessary collector concentrations in normal flotation operations, and the action of the frothing agent in connection therewith' The experimental work comprised accurate determination of the standard solubility product of lead ethyl xanthate, development of a much less laborious

Jan 1, 1947

By T. W. Guy

DURING the past three years the Surface Preparation Committee of the American Mining Congress Coal Operators' Committees has been collecting data on dewatering and drying washed coal, and on screening coal in representative plants in the Eastern and Central bituminous fields. Because of wide variations in bed moisture, such data can be compared only after deducting the bed moisture. It was found that practically every company used a different routine for moisture sampling and determinations. Some reported the moistures as total moistures, others as surface moistures, cur-dried moistures, or oven-dried moistures. For most of the reports it was necessary to esti-mate, from a consideration of the bed moisture and other data available in a given case, corrections to be made in order to obtain surface-moisture figures as a common basis for comparison. At any plant, and regardless of bed moisture, the percentage of surface moisture remaining in a product when the dewatering, or a given stage of the dewatering, has been completed, is the real measure of what has been accomplished. The descriptions and data given with Fig. 1 show that surface-moisture figures show relationships that would not be shown by total moistures. Therefore bed moisture should be deducted, or, if more practicable, the surface moisture of the. products should be meas-ured direct. A preparation engineer finds one per cent, or even a part of one per cent, of surface moisture a very important consideration in the results of his efforts to find the most effective and economical methods of reducing and controlling the surface moisture in his products within the required limits. Therefore it is important for him to have accurate measurements of surface moisture with minimum uncertainty as to whether they some-times include less than the surface moisture and at others all of the surface moisture plus an unknown part of the bed moisture.

Jan 1, 1938

By W. H. Herrnstein, F. H. Beck, M. G. Fontana

Sulfur solubility in a iron was measured in the 750 to 890°C temperature range and was found to be insensitive to ferrite purity within a limited composition range. The permeability of sulfur in ferrite was determined from the internal sulfidation of Fe-Mn alloys. From the solubility and permeability results, the diffusivity of sulfur in ferrite could be calculated. These results are summarized as follows: Dissolved sulfur decreased the lattice parameter of ferrite. The effect of dissolved sulfur on the tensile properties of ferrite at low temperatures was also determined. SINCE sulfur is an important residual impurity in commercial irons and steels, effects associated with the presence of sulfur as a solute in iron are of considerable practical interest. Unfortunately, certain basic information relative to the Fe-S system appears to be lacking in the literature, e.g., the effect of dissolved sulfur on the lattice parameter and mechanical properties of ferrite. In addition, discrepancies exist in previously reported results for the solubility of sulfur in ferrite. These discrepancies raise questions regarding the sensitivity of sulfur solubility to the purity and microstructure of iron. This study was undertaken primarily in an effort to obtain reliable data on the solubility of sulfur in ferrite. Additional objectives included determination of the permeability and diffusivity of sulfur in ferrite by the internal sulfidation method and determination of the effect of dissolved sulfur on the lattice parameter and tensile properties of ferrite. EXPERIMENTAL METHOD Three grades of iron, encompassing a range of impurity levels, were employed in the study. The grades were designated VME (vacuum-melted electrolytic), SPZR (single-pass zone-refined), and MPZR (multipass zone-refined). The composition of each grade is given in Table I. Poly crystalline and single-crystal strip specimens were employed in the solubility experiments. Uniform grain size strip (ASTM 3 to 5) of 0.005 to 0.020 in. thickness was obtained by alternate cold reductions of 60 thickness 60 to 80 pct and recrystallization at 650°C for i hr in pure, dry argon. Single-crystal specimens were produced in 0.010-in.-thick SPZR iron strip by the strain-gradient anneal technique. Recrystallized strip 0.25 in. wide was strained until a Luders band or bands had propagated over the length of the strip; the strip was then annealed by drawing it through a 150°C per in. gradient (890°C peak temperature) at 1 in. per hr in an atmosphere of pure, dry argon. Laue photographs of the crystals produced exhibited no discernible asterism. Specimens were equilibrated with H-H, atmospheres at temperatures between 750" and 890" by one of two methods, each of which makes use of the reaction: The encapsulation sulfurization method was employed in the majority of the solubility experiments. A strip

Jan 1, 1969

By I. L. Dillamore

A purely geomentrical analysis based on oriented-growth relationships is presented to derive annealing-texture orientations in bcc metals from their- known deformation textures. The analysis takes as its starting point a description of- the bcc deformation texture and follows previous work on fcc metals in considering pvobable nurleation sites for recrystallization and the textural limitations on grains growing into a deformed matrix. The analy-sis accounts for the prominent and the minor coinponents of the annealing textures formed from two the deformation textures and can account for the ob-sem:ed temperature dependence of the annealing texture of bcc metals. THERE have been a number of investigations of annealing textures in bcc metals but few attempts to relate these textures to the deformation textures. This has been largely due to the lack of definition of both annealing and deformation textures, neither of which shows sharply defined orientations. It is, however, necessary to get a better understanding of primary recrystallization textures in bcc metals in view of increasingly exacting demands upon the quality of steel sheet for drawing purposes and as a necessary step towards the control of textures through processing. An analysis is presented here which relates annealing textures to deformation texture, by a purely geometrical method. This takes as its basis the oriented-growth theory of recrystallization and makes some reasonable assumptions regarding the make-up of bcc deformation textures and the limitations on growth relationships in bcc metals. Detailed information on this latter point is not available at the present time, and the present analysis may need to be streamlined or extended when such information is at hand. It is felt, however, that despite these limitations the analysis provides useful results and a valuable aid towards understanding the effect of processing variables. 1) BCC ROLLING TEXTURES Different workers have used a variety of descriptions for the texture developed in bcc metals by rolling. For the present purpose it will be assumed that two different deformation textures can be obtained: 1) a texture containing a major (112)[li0] component and a minor (001)[1i0] component for which increasing deformation causes the (001)[li0] component to increase at the expense of the (112)[li0] component, as suggested by Dillamore and ~oberts' (this is the texture predicted to arise starting from randomly oriented material); 2) a t~xture containing the above components and (111)[110] and (ii1)[112] components. This texture could arise from a material with an initial (110)[001] or (iil)[112] texture. It is well-known that the (ll0)[001] orientation rotates to (ii1)[112]that on roll-

Jan 1, 1965

By W. C. Lacy

Urban development in semi-arid portions of the Southwest has upset a natural balance of geological conditions resulting in broad-scale and local subsidence or heaving ground conditions, Subsidence can be traced to two general causes: irrigation of reclaimed desert lands that have dry, low-density soils; and depression of the water table by ground water withdrawal. Accumulation of weathered volcanic tuff produces areas with swelling characteristics. Soil and subsidence studies made in the Tucson area in Arizona illustrate foundation problems typical of the Southwest that must be considered in the design of building codes. Anticipation of problems and the adoption of corrective measures in the design of engineering structures, establishment of pertinent building codes, and urban planning and zoning to obtain optimum land usage and conservation of natural resources demands a thorough understanding of geological conditions of a developing urban area. In the arid to semi-arid southwestern United States erosional and depositional processes result in special situations that require special precautions in building practices. A series of studies currently underway in the Tucson area, prompted by foundation failures and breaking of buried service lines, serves to illustrate some of these relationships between the geological environment and history and engineering problems. ENVIRONMENT The desert region of the Southwest is characterized by isolated mountain ranges rising abruptly from low valleys or plains — the ranges generally occupy less area than do the intervening valleys. In southern Arizona the valley floors step up from near sea level to 2000 ft or more in elevation, and the ranges may rise to over 7000 ft. Desert and steppe-type climates predominate — climate is controlled more by elevation than it is by latitude. Both climate types are characterized by a lack of precipitation, the former more so than the latter. Practically all the rain that falls in the region evaporates; runoff or recharge generally occurs only during the wettest period. Water table levels are generally being depressed. Vegetation is restricted and consists mainly of creosote bush, cacti and sage brush on the deserts, and mesquite, pinon juniper and various types of grass on the steppes. Precipitation varies from about 3 in. on the warm deserts to about 12 in. on the steppes. Most of this falls in the summer or winter, with only rare storms in other seasons. Summer thunderstorms, often accompanied by hail, bring cloudbursts which send torrents of water streaming down the mountains onto

Jan 1, 1964

By M. D. Hassialis, A. F. Taggart

ark' observed some years ago that collector-coating reactions with xanthates and with fatty acids clearly follow paths parallel to those prescribed by the familiar mass-action law for reactions in dilute solutions. He proposed, therefore, the logical hypothesis that they are governed by the solubility-product principle. However, he went astray in the application of his proposal to collector coating by overlooking the fact that coating involves a heterogeneous reaction. A mistaken concept of the meaning of the word adsorption also entered. Wark thought that the concentration of metallic ion that must be used in setting up the solubility-product equation for the coating reaction was that which could be obtained by solution of the mineral. Since this is very low for sulphide ores, and since the amount of the collector ion necessary for coating produces an extremely low concentration, the resulting ion-concentration product, under conditions when coating occurs, is much lower than that which would indicate a saturated solution of the collector-coating compound. Hence he was forced to the position that the solubility product governing the coating is much smaller than the standard solubility product. To justify this position it was necessary to postulate a coating mechanism that did not obey the ordinary laws of chemical reaction. This Wark did by adopting the concept that adsorption is a property of matter, rather than merely a more or less ephemeral local concentration thereof. Thus he says (p. 142 of ref. I): "Adsorption is not a purely physical property of the solid surface, for the specific nature of the adsorbed molecule or ion is important." The result was that he destroyed the great potential utility of his postulate by tying it to this erroneous concept in the words (pp. 142, 143): "It will be obvious that the adsorption solubility product is less than the normal solubility product." The writers have found quantitatively in the case of galena and potassium ethyl xanthate, and semiquantitatively in the case of covellite and the same collector, that the coating reaction does follow the mass-action law to the extent that coating occurs when the ordinary solubility product of the coating compound is exceeded, and that coating does not take place under the reverse conditions. In the course of the investigation leading to the establishment of this fact it was necessary to work with xanthate concentrations so low (down to 0.0004 mg. per liter), that very long conditioning times, and bubble-contact times of as much as 16 hr. were necessary sometimes to follow the reactions. The results have led to some illuminating conclusions as to necessary collector concentrations in normal flotation operations, and the action of the frothing agent in connection therewith' The experimental work comprised accurate determination of the standard solubility product of lead ethyl xanthate, development of a much less laborious

Jan 1, 1947

By G. D. Van Arsdale

THE paper of Mr. Posnjak presents a laboratory confirmation of the well known facts that air ox-idation of pure solutions of ferrous sulfate is slow and difficult and that, like many other similar reactions, the speed, may be greatly accelerated by the presence of other substances, often in very small amounts, the effect of the presence of copper being determined ex-perimentally in this case. However, it should not be. overlooked that copper is always present in heap leach-ing solutions in amounts equal to or greater than those in the experiments described; therefore the paper may be considered as an explanation of present results rather than a possible improve-ment to be added to present practice. It is not practicable and it does not pay to precipitate copper by ce-mentation below a point about 5 lb. per 1000 gal., equivalent to about 0.0005 mol. Cu. per liter, compar-ing with the approxi-mately 0.0009 mol. per liter of curve 2 in the diagrams given of course, also, in the heaps local concentrations are usually very much higher than this, which is also true of the effluent li-quors, so that I feel that it is safe to say that copper is already present in amount sufficient to realize, as large an accelerating effect as is practicable. Too much im-provement or refinement cannot be expected in a method of this kind, due to commercial limitations. It should be remembered that chemically and physically there is no sharp dividing line between leaching in place, heap leaching, and the usual tank leaching practice, practi-cally the same reagents being used in all three. From the viewpoint of extractions, etc., it is not common sense to apply leaching in place to an orebody carrying enough copper to pay for mining; and the same is true of heap leaching, for an ore carrying enough to pay for the crushing, handling, etc., of ordinary leaching. That is to say, leaching in place should properly be consid-ered only for an ore too low-grade to pay for mining, and heap leaching for the next higher grade, still how-ever too low-grade to pay for crushing and other re-finements. There is no advantage in leaching without mining or in heap leaching except lower cost of in-stallation and handling; on the other hand there are very distinct disadvantages which are inherent and which should prohibit their use except where necessity requires. The object of metallurgy is to make money out of the handling of ore, and it is purely a question of money as to how far we can go in "improving" or

Jan 7, 1927

By John Tyssowski

In 1925, Harry Howard Stout, then metallurgist for Phelps Dodge Corporation, while investigating the cleaning of cathode copper by various gases at elevated temperatures below the melting point of the metal, observed in the laboratory that particles of pure copper heated in a closed tube filled with hydrogen seemingly "stuck together." By further investigation he found that there was actual crystal growth across the boundaries of the particles of pure metal; in other words, there was a complete new crystal realignment and growth throughout the newly formed copper mass. It was coalescence, not adhesion; the several particles had become one unit. From this discovery has been developed the coalescence process, whereby copper of cathode purity is squirted out in semifabricated form from an extrusion press, by the application of about 3000 tons pressure on a 10-in. piston. Stout decided that cathode copper produced by electrolytic deposition was the logical source of the pure copper required for the coalescence process, but as there was no way of reducing the ordinary tough commercial cathodes to the small particles required he was confronted by a serious problem at the outset. Under his direction, this problem was solved by William H. Osborn and Harry Howard Stout, Jr. They developed the process and technique for producing cathode copper in brittle, friable form, and to them must be given the greater part of the credit for this phase of the development program as well as for that relating to the gas cleaning of the cathode particles. Concurrently, the three metallurgists worked on the problem of effecting a complete union of the cathode particles. Adequate washing was all that was needed to free the particles from electrolyte solution and slimes. A press was designed to produce briquettes of the proper porosity and density, and a method was devised of removing surface oxidation from the particles of cathode, by treatment in an atmosphere of deoxidizing gas at an elevated temperature. The temperature was determined at which the surface cleansing and preheating could be done in one operation, and for this a charging and preheating furnace in which there is maintained a positive pressure of deoxidizing gas atmosphere was designed. And finally, a method of feeding the heated briquettes of deoxidized cathode copper into an extrusion press without contamination from the air was evolved. For the final stage, a press was required because not only heat but pressure was required to obtain complete growth of the new crystals between the cathode particles as well as the elimination of all voids or non-coalesced areas. All essential stages of the process are protected by patents or patent applications in the United States and principal foreign countries, and the copper is produced on a commercial scale.

Jan 1, 1941

By R. D. Leitch, W. P. Yant, R. R. Sayers

In 1924, the United States Public Health Service was requested to undertake a special study of stream pollution. The Public Health Service asked the United States Bureau of Mines to take up the study because the training and experience of the personnel of the former was considered not to be as well suited to this type of investigation as that of the Bureau of Mines. Under H. Foster Bain, then Director of the Bureau, field investigations were begun in the spring of 1925. Along with mine-drainage wastes, the problem of gas-house and coke-oven waste was investigated in the laboratory and a method of treatment by sodium hydrate and benzol was found to be promising. The idea was obtained by A. C. Fieldner, chief engineer of the Bureau Experiment Stations, on a trip to Germany in 1924. He saw a practical application of the process, but obtained no information as to definite chemical or mechanical processes. Because of the then pending American patent applications by the German firm, we made no attempt to develop our findings further. Shortly afterward, a similar method of treatment was developed in the United States,' and since that time we have devoted our attention entirely to mine drainage. This paper is a presentation of some general facts and information gathered during the past five years on coal-mine drainage. Scope of Work There was such a diversity of opinion at the time this work was begun, on the whole subject and apparently so little accurately known, that it was decided to undertake a basic study from which first, certain definite information might be evident, and second, what might be considered

Jan 1, 1931