Search Documents

By Frederick C. Langenberg

IT has been shown1 that copper can be removed from iron-base alloys by solvent extraction with molten lead and sodium sulfide slags. In these processes copper removal is favored by a positive deviation of copper in iron from ideal behavior. Chou' determined the distribution of copper between liquid silver and iron and obtained a value for the activity coefficient of copper in iron at 1600°C, y°, of 9.12. Chipman" calculated the activity coefficient from the Fe-Cu phase diagram to be 12 at 1600°C. More recent work by Koros and Chipman" yields a value at 1600°C for y V equal to 8.0. In this latter work, the distribution of copper between silver and iron was measured at 1600°C, while the activity of copper in the silver phase was determined from calculations based on the Ag-Cu phase diagram. The present work presents another value of based on calculations from the Cu-Pb phase diagram, on the heat of mixing data for the Cu-Pb system, and on an experimental study of the distribution of copper between iron and lead at 1600°C. These experiments were part of a larger research on the removal of copper from iron-base alloys conducted at The Pennsylvania State University. Experimental Procedure—The distribution of copper between pure iron and lead at 1600°C was made in the furnace assembly shown in Fig. 1. The melts were made in high purity alumina crucibles under an atmosphere of prepurified argon. Temperatures were read with an optical pyrometer sighted into a %-in. hole drilled in the inductor. Extensive calibration of the optical readings with immersion readings had been carried out previously. The initial charges consisted of 100 g of electrolytic iron and varying weights of copper. The melts were brought rapidly to 1600°C and 75 g of lead added. The temperature was quickly readjusted to 1600°C, and the melts were held for 10 min at this temperature. A sample was then drawn from the iron layer in a fused silica tube. This sample was analyzed to determine the copper content of the iron layer at equilibrium, while the copper content of the lead layer was determined from a material balance. The validity of the material balance was confirmed by a chemical analysis of the entire lead layer for one heat in which the crucible was removed and quenched after the iron sample was taken. The calculated copper content of the lead-rich phase was 1.18 pct; while the entire lead layer analyzed 1.20 pct Cu. The distribution results are shown in Fig. 2. The distribution constant, N,.'r'"/N, is equal to 3.95. Discussion—From the Cu-Pb phase diagram' it can be seen that lead-rich liquid Pb-Cu solutions

Jan 1, 1957

By John Brown

As a part of a symposium on the relations of structure to ore deposi-tion, in February 1938, the writer presented some tentative opinions derived from his experience with a number of important lead-zinc replace-ment deposits. These ideas were set forth, as a basis for discussion and a stimulus to further inquiry, in a mimeographed leaflet that read as follows: Intimate acquaintance with a number of lead and zinc deposits in metamorphosed limestones seems to indicate the existence of certain common features from which can be established some general principles governing the localization of ore in this type of formation. It is suspected that these principles can be applied, with modifica-tions, to mineralization in unmetamorphosed limestone. In metamorphosed forma-tions, some observed rules are as follows: 1. Bands or masses of pure limestone are very resistant to replacement by ore solutions, and are likely either to contain no ore or to resist replacement until near the end of mineralization. The reason for this apparently is physical, not chemical, since microscopic data indicate that when ore is deposited by far the greater part of it substitutes for carbonate. The chief factor is believed to be a lack of porosity in massive limestone that has undergone flowage and recrystallization. 2. Masses of intensely siliceous or silicated rock are likewise unfavorable ore receptacles. This seems to be accounted for by two factors: (a) chemical unsuit-ability or resistance to replacement, and (b) physical resistance to small-scale brecci-ation, which might facilitate the opening of effective channelways for solutions. Some low-grade ore may occur, however, and also sporadic fracture fillings. 3. The optimum condition for ore reception appears to be found in bands or areas containing carbonate and silicates (or quartz) intimately mingled in something like equal proportions. In this situation movement is likely to result in mixed flowage and fracture, producing a fine-textured porosity that admits solutions freely and provides access to an abundance of replaceable carbonate. Cleavage cracks in some minerals such as diopside are believed to facilitate the penetration of solutions. 4. Certain minerals or assemblages are regarded as favorable impurities in a lime-stone and others as unfavorable. Original quartz, and subsequently developed diopside, and perhaps garnet, are typical favorable pre-ore gangue; in general rather equidimensional, brittle minerals. Tremolite, biotite, and probably wollastonite, are typical unfavorable pre-ore gangue; in general highly elongated and somewhat flexible minerals likely to develop under strong shearing stresses. 5. Tentative opinion is that the ratio of lime and magnesia in a limestone-is of little or no importance.

Jan 1, 1940

By J. S. Marsh

The student of steelmaking is all too well acquainted with the fact that in many instances he must deal with data that in graphical representation exhibit the property most desirable in bird shot. This is scarcely mystifying, since the effort to establish one variable as a function of another is usually hampered by the simultaneous operativeness of two or three other factors that may be important. A large part of arriving at relationships that have the pleasing self-consistency of, say, precise measurements of thermal expansion, consists of determining what factors must be held constant-—an even larger part usually consists of collecting data for which those factors have been so maintained. It is not intended to imply that functional relationships in the physical chemistry of steelmaking are hopelessly obscure; on the contrary, it is merely necessary to be undisturbed by marked deviation of some points from a curve that otherwise makes sense. A reaction mechanism suggested by such a curve may call attention to hitherto unsuspected factors operative in the origin of the deviating points, and thus permit another step to be taken in the direction of fuller understanding. It is proposed, therefore, to suggest several empirical relationships. Even though the approach is not always rigorous, deviations caused by simplifying assumptions appear to be too small to obscure a provisional It has been appreciated for some time that the carbon-oxygen reaction in liquid steel is highly important. For example, Körber et al.,' in introducing a summary of their extensive work on steelmaking reactions, said: "... the far-reaching and truly dominating action of carbon upon the metallurgical reactions will be especially stressed ..." In "Basic Open Hearth Steelmaking"2 (hereafter BOHS, for simplicity), it is accepted repeatedly that the various slag-metal interactions are nearly always controlled by the carbon-oxygen reaction. Before further discussion of this reaction, however, it will be worth while to consider briefly the carbon-oxygen equilibrium. In BOHS (p. 483) it is stated that: When liquid iron is brought into contact with gases containing carbon monoxide it absorhs carbon and oxygen. Conversely the carbon and oxygen in the metal unite to form carbon monoxide which is evolved from the bath during the open-hearth boil or while rimming ingots are solidifying. . . . When the equilibrium pressure is one atmosphere the equilibrium-constant equation simplifies, on the assumption that the activity of each element is equal to its percentage, to a constant which has been so much used that it has acquired a special symbol m. where m = %C X %O

Jan 1, 1945

By F. J. Radd, R. L. McGlasson

The mechanisms of corrosion and corrosion fatigue damages to sucker rods are examined from a fundamental electrochemical viewpoint, and the relationships of sucker rod microstructures to these damaging effects are defined. The common corrosive agents in crude oil production and storage are discussed as to types of attacks that they cause. The variations of fatigue strength with alloy content, surface preparation, and stress ranges are analyzed. Finally, conclusions are drawn as to how microstructures largely influence and control sucker rod performance. INTRODUCTION Greater than 90 per cent of the crude oil produced by artificial lift methods is produced through sucker rod pumping systems. In the USA each year more than $14 million is spent for sucker rods in new and old pumping installations. It is important to make this investment a wise one. Essentially, the sucker rod system is a long series of steel rods, operating under alternating stress loadings and under mechanical vibrations, which connect the surface power source with the subsurface pump. These rods often operate in a variety of corrosive media, including water, brines, carbon dioxide, hydrogen sul-fide, and air. Basically, this paper is concerned with the problem of the behavior of certain steels in various corrosive media under high and dynamic stress patterns. The main objective of this paper is to show how, once the stress effects and the corrosive environments are defined, one can still realize structural control and beneficial influence upon corrosion and corrosion fatigue. FUNDAMENTAL DEFINITIONS AND ANALYSIS In the corrosion and stress behavior of this solid state mixture of iron and iron carbide called steel, one must analyze upon what major factors does its service life depend and of what, exactly, is steel composed. The former question can be referred to two external factors and two internal factors. The two major external factors are: 1. the nature of the stress patterns — size and range of stresses present 2. the nature of the corrosion — erosion environment — the corrodent and/or wear involved The two fundamental internal factors that govern the strength and useful life of a steel both in normal duty and in heavy-duty corrosion service are: 1. the nature of the steel volume properties 2. the nature of the steel surface properties For the latter question normal steel is defined as a solid mixture of iron and iron carbide particles, generally with certain accidental and intentional elements present. (The amount of iron carbide present is determined by the carbon content of the steel.) These additional elements generally dissolve into either the iron (ferrite) or the iron carbide (cementite) components.

Jan 1, 1955

By Robert B. Bossler, Parke A. Dickey

The presence of connate water in oil sands is of far greater practical significance in secondary oil-recovery operations than it is in primary operations. The percentage saturations of oil, water, and gas in a depleted field determine whether it will be economically possible to recover oil by secondary methods, and whether water-flooding or gas-driving, or either, will be successful. It is suggested that economic recovery of oil by secondary water-flooding can occur only when a rich bank of oil is formed by the encroachingm water. If the sand has a greater effective permeability to water than it has to oil before flooding, a bank will not be formed, and water-flooding will not be successful, although gas-driving may be. Published results of laboratory work indicate that the effective permeability of a sand to oil and water depends primarily on the saturation of the sand by these phases. They also indicate that a small difference in relative saturation produces a large difference in effective permeability to the phase in question. There thus exists a critical range of saturations, wherein a small change in oil and water content of the sands will make water-flooding possible or impossible. In gas-drive operations the water saturation is less critical but no less important. The presence of connate water in a sand increases the proportion of the residual oil that may be recovered by gas drive. Sands containing oil saturations too low and water saturations too high to make water-flooding possible can often be subjected to gas drive with economic recovery of oil. The results of laboratory work on test samples that do not contain water cannot be applied to normal field operations. More tests on cores containing water as well as oil are desirable, and the improvement of coring technique is necessary. However, sufficient data are already available to enable an operator to use core data intelligently in estimating the chances of a secondary oil-recovery program. Introduction In recent years laboratory work has led to a much better understanding of the principles of oil-reservoir performance. The general principles of the expulsion of oil from sandstone by gas or water were developed by geologists of the Second Geological Survey of Pennsylvania in the 1870lsl but only recently has the mechanism of gas or water drive been intensively investigated. Most published articles have large the facts established in the labora tory to the primary production of oil from flush fields- This Paper is not based on any new observations, but is an attempt to apply some of the conclusions obtained in the laboratory and described in the literature to the recovery of oil from depleted pools by secondary methods. One of the most important factors that determine whether or not a secondary-recovery operation is economically successful is the ratio of injected fluid to oil recovered. This ratio may be expressed as the over-all or cumulative gas-oil ratio if gas is the driving medium, or water-oil ratio if water is the driving medium. Recent theoretical and experimental work has shown that the relative amounts of

Jan 1, 1944

By Parke A. Dickey, Robert B. Bossler

The presence of connate water in oil sands is of far greater practical significance in secondary oil-recovery operations than it is in primary operations. The percentage saturations of oil, water, and gas in a depleted field determine whether it will be economically possible to recover oil by secondary methods, and whether water-flooding or gas-driving, or either, will be successful. It is suggested that economic recovery of oil by secondary water-flooding can occur only when a rich bank of oil is formed by the encroachingm water. If the sand has a greater effective permeability to water than it has to oil before flooding, a bank will not be formed, and water-flooding will not be successful, although gas-driving may be. Published results of laboratory work indicate that the effective permeability of a sand to oil and water depends primarily on the saturation of the sand by these phases. They also indicate that a small difference in relative saturation produces a large difference in effective permeability to the phase in question. There thus exists a critical range of saturations, wherein a small change in oil and water content of the sands will make water-flooding possible or impossible. In gas-drive operations the water saturation is less critical but no less important. The presence of connate water in a sand increases the proportion of the residual oil that may be recovered by gas drive. Sands containing oil saturations too low and water saturations too high to make water-flooding possible can often be subjected to gas drive with economic recovery of oil. The results of laboratory work on test samples that do not contain water cannot be applied to normal field operations. More tests on cores containing water as well as oil are desirable, and the improvement of coring technique is necessary. However, sufficient data are already available to enable an operator to use core data intelligently in estimating the chances of a secondary oil-recovery program. Introduction In recent years laboratory work has led to a much better understanding of the principles of oil-reservoir performance. The general principles of the expulsion of oil from sandstone by gas or water were developed by geologists of the Second Geological Survey of Pennsylvania in the 1870lsl but only recently has the mechanism of gas or water drive been intensively investigated. Most published articles have large the facts established in the labora tory to the primary production of oil from flush fields- This Paper is not based on any new observations, but is an attempt to apply some of the conclusions obtained in the laboratory and described in the literature to the recovery of oil from depleted pools by secondary methods. One of the most important factors that determine whether or not a secondary-recovery operation is economically successful is the ratio of injected fluid to oil recovered. This ratio may be expressed as the over-all or cumulative gas-oil ratio if gas is the driving medium, or water-oil ratio if water is the driving medium. Recent theoretical and experimental work has shown that the relative amounts of

Jan 1, 1944

By Kenneth C. Vincent, A. M. Gaudin

IN a study1of the action of amyl xanthate on chalcocite in water suspension, it was found that if the xanthate is added in relatively large quantity the xanthate group can be accounted for in three forms: (1) as xanthate ion remaining in water, (2) as benzene-soluble cuprous xanthate on the chalcocite, (3) as a benzene-insoluble coating on the chalcocite. Reduction in the amount of xanthate added leads to disappearance of form 1 then of form 2. With minute quantities of added xanthate, substantially all the reagent is of the "unleachable" kind. Yet this unleachable xanthate can be dissolved by pyridine to form a soluble cuprous xanthate complex, and it is sufficient in effectiveness to make chalcocite flotable even if insufficient in quantity to form a complete monomolecular film on the mineral. In that study it was also found that chalcocite abstracts cuprous xanthate from benzene solution, in what may (or may not) be a case of molecular adsorption. It seemed desirable, therefore, to study further the "unleachable" xanthate on the chalcocite, and particularly to ascertain whether it is formed as a result of the benzene leach or is actually formed during the conditioning of chalcocite in aqueous xanthate solution. A splendid tool to make such studies has recently been perfected; that is, the use of radioactive spies or tracer atoms. With this tool, it was thought possible to answer the problem stated above, but, unfortunately, this did not prove to be true. Answer to the flotation question was clouded by the existence of rapid and selective diffusion of copper atoms in the solid mineral-a phenomenon that was totally unexpected yet remains interesting and perhaps important. METHOD OF RADIOACTIVE SPIES The method of radioactive spies is discussed in many places. Two convenient references are the article by Evans2 and the book by Pollard and Davidson.3 The method was first developed by Von Hevesy and Paneth in 1913, when only natural radioactive isotopes were available. These isotopes are few in number, and so the method remained limited in scope. Recently the synthesis of over 350 active isotopes of all the known stable chemical elements4 has opened widely expanded possibilities for the method. A fundamental tenet of the method is that a radioactive atom and a nonradioactive atom are exactly alike until disintegration of the radioactive atom. Then, by its sudden death, the spy reveals its location. The relative abundance of spies at various locations makes it possible to ascertain the relative abundance of the corresponding nonradioactive atoms at the same times and locations. A second fundamental tenet of the method of radioactive tracers is that the radioactivity lies in the nucleus of the atom: transfer of radioactivity from one

Jan 1, 1944

By Jasper L. Stuckey

HISTORY IT is not known when kaolin mining was first begun in North Carolina. Evidence, in the form of excavations and primitive tools, indicates that some of the deposits were worked in prehistoric times. It has been suggested that the prehistoric mining was for mica, but the workings were all in altered or partly altered pegmatite material and the dumps do not represent the amount of material removed. Some of the early openings may have been made in search of kaolin or semi-kaolinized feldspar which was sold to English1 traders along the coast and used in some of the early English porcelains. In 1944,2 an application was made for an English patent to produce porcelain from an earthy mixture obtained from the Cherokee Nation in North America. It is well established, however, that the occurrence of kaolin in western North Carolina was known in England by 1767. In that year, Josiah Wedgewood sent T. Griffiths3,4 to what is now Macon County, North Carolina, to secure a supply of kaolin for use in England. Griffiths diary, now in Etruria Museum, Stokes-on-Trent, contains a most interesting account of his experience. Kaolin was discovered at St. Austell, England, shortly after the voyage of Griffiths, which probably accounts for the lack of further interest in American kaolin. Between 1767 and 1888, there are no records of kaolin mining in North Carolina. In the latter year, however, mining was begun near Webster, Jackson County, and, in the intervening period, has become an important industry. For some 20 years, kaolin mining was carried on chiefly in Jackson, Macon, and Swain Counties. About 1904, it was begun in the Spruce Pine district and for the past 20 years most of the kaolin mined in the State has come from Avery, Mitchell, and Yancey Counties. DISTRIBUTION The kaolins of North Carolina are limited in occurrence to the Piedmont Plateau and Appalachian Mountain area of the State. While kaolins are widespread in the Piedmont Plateau, having been prospected for in Rutherford, Cleveland, Gaston, Granville, Lincoln, Catawba, Iredell, Richmond, Moore, Randolph, and Montgomery Counties, the production from that area has never been important. The known deposits of commercial importance are limited entirely to the mountain area of the State. While kaolins occur widely distributed throughout the mountain area and have been prospected for in many counties of that area, commercial production has come chiefly from two districts. One of these includes Jackson, Macon, Swain, and Haywood Counties. The other includes Avery, Mitchell, and Yancey Counties. GEOLOGY With few exceptions, all the known kaolin deposits in North Carolina contain

Jan 1, 1947

By A. J. Phillips, A. A. Smith, J. S. Smart

THE preparation of a sufficient quantity of high-purity copper for extensive laboratory use in the study of impurity effects has been an integral part of a research program in progress at the Central Research Laboratory of the American Smelting and Refining Co. for the past several years. Initially the degree of purity desired was that necessary to meet two essential requirements for experimental accuracy: (I) no impurity was to be present in the copper in an amount capable of producing a detectable effect on the properties to be studied, (2) even the minor changes in properties caused by the addition of extremely small amounts of individual elements were to be measured without significant interference from contaminants. In the course of the investigation, evidence has accumulated to justify the conclusion that this copper is of exceptional purity; in fact, no impurity can be detected by any chemical method or spectrographic technique known to the authors. The present paper describes the method of production of the copper and presents some of its properties. PREPARATION OF HIGH-PURITY COPPER The elimination of impurities from commercial electrolytic copper is accomplished by a three-step purification process. The first operation consists of an electrolysis through a purified CuS04-H2SO4 electrolyte using bagged anodes, low current .density (5 amp. per sq. ft.) and low temperature (25°C. max.). The electrolyte is prepared from commercial Cu2SO4 and is purified by heating the solution and adding I gram Fe as Fe 2(S04)3 to each 100 grams dissolved copper; sufficient hydrated oxide of copper, prepared from Cu2SO4 and NaOH, is supplied to precipitate Fe(OH)3, which carries down arsenic, antimony, tin, selenium, tellurium and other minor constituents. Silver and remaining traces of lead are removed by addition of Na2S to the acidified filtrate, which is then refiltered after standing hot overnight. The cold solution is made up to 30 grams per liter Cu and 150 grams per liter H2S04 and introduced without addition agents into the electrolytic system, which consists of a double row of hard-rubber battery boxes with the inside webbing and partitions removed, arranged in seven steps of ascending height. Electrolyte is uniformly supplied to the two highest cells by glass siphons operating from a constant-level reservoir, and flows by gravity through the bank of seven cells, entering each at the bottom and leaving at the top. Glass air lifts continuously supply the returning liquid to the constant-level reservoir for recirculation. Each cell contains three 434 by 43a by I-in anodes cast from high-quality electrolytic wire bar copper, various lots of which have been used with equal success. The anodes are pinned to sheet copper hangars shaped to prevent crawl of the electrolyte to the multiple-wired bus bars-which would result in fouling of the contacts and hang inside wool flannel bags stretched over open wood frames. The deposit

Jan 1, 1941

By Michael Chender

INTRODUCTION The project financing described elsewhere in this book is available to major mining companies on the basis of a strong balance sheet, a significant equity position in a project of proven feasibility, and a demonstrated ability to bring ore deposits into production. "Junior" mining companies, which are most active in Canada, Australia, the US, and South Africa, by definition do not meet these criteria. In many cases, junior companies will need to raise money simply to cover the costs of acquiring and exploring potential deposits. In what follows we will look primarily at junior financing practices in the US and Canada, although the same general principles will apply in Australia and South Africa. The principal vehicles for junior mine company financing are limited partnerships, the private placement of securities and debentures, and public offering of securities, and property deals with stronger companies, in the form of leases, earn-ins and co-ventures. The cost (in terms of dollars or equity) and, to some extent, the applicability of using these difficult approaches varies with the stage of development of the property and with the corresponding degree of risk to the investor. Much junior company fund raising is, in fact, "interim" financing in that it allows the company to improve its properties and develop its assets to the stage where more favorable financing arrangements may become available. Companies will therefore often use several of the approaches described above during the development life of a specific property. LIMITED PARTNERSHIPS Limited partnerships and syndications are a popular way of structuring the initial private financing of mine developments because of their attractive tax consequences for the well-to-do investor. Costs of exploration and development can in many countries be passed through as deductions to the limited partners, who are thus able to gamble on a possible windfall at little real cost. In addition to private Canadian funds, much German money flowed into Canadian exploration ventures on this basis, but stopped in 1982 due to economic conditions in West Germany. In the US, recent regulations have, in the great majority of cases, taken away the ability to "shelter" income in mining limited partnerships. Deductions taken by the individual investor cannot exceed the amount of money he actually has at risk. Nevertheless, the allowable deductions are still attractive and some of the major mining companies are now beginning to look at limited partnerships as a vehicle for attracting additional exploration funding. Ranchers Exploration and Development has successfully put together several drilling funds on this basis. THE PRIVATE PLACEMENT Initial funding for the acquisition and preliminary exploration of prospects is often accomplished through a private placement of unregistered securities or, where it is not a problem to carry debt on the statement, by a private placement sale of debentures. A fledgling company wishing to do a public offering may well be advised by an underwriter to accomplish a small private placement as a precondition of the larger offering. In this way, the sale of the registered securities is not inhibited by the company starting out with a debt-ridden balance sheet and no demonstrated ability to secure the additional financing generally necessary beyond the proceeds of that offering. In the US, the securities offered in a private placement are not registered with the Securities and Exchange Commission (S.E.C.) but are restricted as to their resale, and could be further restricted by a underwriting agreement

Jan 1, 1985

By T. S. Spice, H. L. Lovell, R. W. Utley

With the increased demand for lightweight aggregate, such materials have been manufactured from slags, clays, slates and, to a minor extent, the refuse of coal preparation processes. The latter source is attractive due to current interest in eliminating air pollution and improving the unsightly appearance of refuse piles as well as potential economic advantages, if a satisfactory product can be manufactured. A study has been made relating the composition of coal refuse, expressed as washability data, and the properties of a resulting aggregate. Three different refuse samples (bituminous and anthracite) were separated at gravities ranging from 1.4 to 2.96. Their chemical composition was determined. Aggregates were prepared in the laboratory from these fractions before and after ashing, at temperatures between 1250' and 1350°C. The specific gravity, expansion and compressive strength of the products were measured. The response of the refuse to bloat is related to the chemical composition of the ash to yield a glass of desirable viscosity and to the presence of a material which will form a gas in the appropriate temperature range. Carbonaceous material within the particle is a negative factor since after the glassy phase forms, oxygen cannot enter the mass thus inhibiting bloating. Precombustion of the refuse is also detrimental since it removes substances of gas-forming capability. The fraction sinking at 2.60 yielded an aggregate which had the lowest specific gravity, greatest expansion and greatest compressive strength. The purpose of this study was to seek and evaluate possible relationships between the composition of coal refuse, as expressed by washability data and factors affecting the production of a lightweight aggregate from refuse by bloating. The study was related to an intense program in the Department of Mineral Preparation at the Pennsyl- vania State University to study the possible elimination of air pollution from coal refuse fires by producing a low-carbon secondary refuse. Another phase of this program is considering possible uses of such a secondary refuse. Thus one study was to determine if a lightweight aggregate could be produced from this new refuse material and what effect the nature of refuse beneficiation would have upon the characteristics of a commercial aggregate product. It was hoped that these studies would assist in the design of a process and in establishing the optimum specific gravities at which refuse separation could be made in respect to the production of a low grade fuel from the float product and a raw material for lightweight aggregate from the sink product. The combination of producing a saleable low grade fuel and a lightweight aggregate, while at the same time minimizing disposal costs and air pollution contributions would be attractive to the coal mining industry. MECHANISM OF BLOATING Austin, Nunes and Sullivan,1 Ehlers,3 Everhart, 4 Riley7 and others, have stated that bloating is an expansion process in which two essential conditions exist simultaneously. These are: the development of a glassy phase over a relatively wide temperature range (the viscosity of this glassy phase plays a major role in the retention of the evolved gases) and the evolution of gases (SO2, SO3, CO2 and O2) from mineral decomposition in sufficient quantities at appropriate temperatures to form a cellular structure in the mass. Unless these two "type" reactions take place at the same time or in overlapping ranges of time and temperature, cellulation will not occur. In this event, the gas will escape or the melt will be too fluid to retain it; or if retained, the cells may be too large or the walls too thin for good strength in the product. The stages that occur when clays and shales are heated in an oxidizing atmosphere may be summarized as follows: 1) Drying and removal of free water to 200°C. 2) Absorbed water dehydration period (200 to 480°C). 3) Chemically-combined water dehydration period (480 to 700°C).

Jan 1, 1965

By Edwin F. Brush, John Chipman

Published data on the activity of carbon in binary and ternary austenite at 1000°C are reviewed. The composition variables are . The coefficient, Vj, has the value for substitutional elements but may be assigned a ualue -1 for silicon to effect a simplification on the mathematical treatment. The activity coefficient PC = is obtained from gas equilibrium data. For the ternary systems studied the Henrian activity coefficient is given by the expression: The principle advantage in cornparison with the analogous expression in terms of atom fractions is found in the fact that for most systems the final term and in many the last two terms are zero. Values of the interaction parameters are tabulated and the graphical comparison of the equation with experirt~ental data is sho,wn in several figures. The thermodynamic properties of the solid solution, austenite, are of considerable importance in the heat-treatment of alloy steels and in other aspects of ferrous metallurgy. Early studies embodied in the Fe-C diagram have been extended to include other binary and some ternary diagrams. Our best hope of obtaining a useful thermodynamic treatment of reactions in complex alloy steels will not be found in quaternary and quinternary phase diagrams but in determinations of activities and interaction relations among the several solute elements. The foundation for such a development was laid by smith' in his early studies of the activity of carbon in Fe-C alloys and his subsequent work on Fe-C-Si, Fe-C-Mn, Fe-C-Ni, and Fe-C-Co solid solutions.2"4 Other observers have also made noteworthy contributions and these will be discussed and correlated here in the light of a somewhat simplified mathematical treatment of solute interactions. Fe-C AT 1000°C In a recent review of the thermodynamic properties of binary Fe-C austenite it was shown that the simple mathematical treatment employed by smith' was capable of describing all the published results on this solution. The treatment utilizes the atom ratio, yc = nC/nF,, rather than the atom fraction. The activity of carbon is proportional to the equilibrium gas ratio, either measured on a scalk in which the activity of graphite is taken as unity or, alternatively, aC may be set equal to yc at infinite dilution. In either case the ratio aC/y = (PC, the activity coefficient. It was found that the experimental data of smith1 and those of Diin-wald and wagner; Bungardt, Preisendanz, and Lehn-ert,' and Scheil, Schmidt, and Wiinnings at temperatures of 800" to 1200° C as well as reliable data on the solubilities of graphite and cementite could be represented by the equation for which graphite is the standard state: The data on alloyed austenite have been obtained at 1000°C. For this temperature, the "Henrian" activity coefficient (which is unity at infinite dilution) is: FOr an interstitial solute such as carbon in austenite it has been shown by statistical mechanicsg that the activity in the infinitely dilute solution is proportional to the ratio of the number of lattice sites occupied by carbon to the number of yet unfilled lattice sites. A variable zz proportional to this ratio serves as a useful measure of concentration:" in which b is the number of lattice sites provided by each atom of solvent; in austenite b = 1. The Henrian activity approaches zz at infinite dilution and the ratio a is the activity coefficient. The effect of a change in concentration is then given by: It has been shown further that in some systems the derivative in Eq. [4] remains constant over a wide range of concentrations. In such a case second-order terms become negligible and the Henrian activity coefficients is:

Jan 1, 1969

By R. E. Zimmerman

THE separation of fine sizes of coal from its impurities by means of various flotation methods has become of increasing importance in the coal industry. This, no doubt, will be even more so in the future as the quantity of high grade coal is depleted, particularly that used for metallurgical purposes. The purpose of this paper is to describe and report the results of research work done under the auspices of the Pittsburgh Coal Co. to determine the amenability of their bituminous fine sizes of coal to flotation, to investigate the value of various reagents and factors affecting their use, and compare the results between froth flotation and bulk oil flotation. Compared with the preferential flotation of complex minerals, or ores, the flotation of coal is comparatively easy. However, this statement should not lull one into the feeling that there are no special problems involved. For instance, the separation of coal from pyrite in high sulphur coals is still far from being 100 pct successful. Size consist has considerable effect on reagent consumption and recovery. Other factors will be described and finally it must be remembered that in the flotation of coal a low priced material is being treated and thus economic considerations govern more closely its application than is generally the case in treating other minerals. As a result of the research work done by the Pittsburgh Coal Co. on the flotation of coal, it was concluded that it was practical to clean the -48-mesh coal commercially by froth flotation and after several different types of flotation units and circuits were investigated by means of pilot plants, large scale units were installed at their Champion Nos. 1, 4 and 5 Preparation Plants for the cleaning of -48-mesh slurries. These large scale operations have been recently described by D. H. Davis. 1 C. P. Proctor and C. B. Carlson2 in their chapter on Froth Flotation of Coal in the AIME Seeley W. Mudd series book on Coal Preparation describe some of the practical applications of our Pittsburgh Coal Co. laboratory work in actual plant practice as well as summarizing part of the investigational work. The author presents this paper, however, as a supplement to their reports, and records the basic research accomplished in the laboratory investigational work as well as the results of experi¬ments using bulk oil flotation. In presenting this work the author wishes to state much more work must be done in applying the principles of flotation to cleaning coal, especially in view of recent studies and practices in other mineral beneficiation fields. METHODS OF CONDUCTING LABORATORY TESTS The bulk of the research work was conducted in the laboratory of the Champion No. r Preparation Plant. This plant has elaborate facilities for sampling and analyzing coal and proved to be an admirable location

Jan 1, 1948

By G. W. Healy, L. F. Sander

was investigated by reacting thin discs of calcium oxide with gas mixtures of CO2, CO, and Son. Its value was 19,300 * 300 cal independent of temperature in this range. No solid solubility of sulfur in calcium oxide was detected within the limits of the experimental method and it is estimated to be below 0.025 pct by weight. The importance of lime in desulfurization is well-established but complete information on the pure phase equilibrium: CaO + 1/2 s2 = CaS + +02 [11 is not yet available. The goal of this work was to evaluate solid solubility of CaS in CaO and to determine the free-energy change associated with Reaction [I] at temperatures of 1400" to 1650°C. The equilibrium constant for Reaction [1] can be written: It is convenient to rewrite Eq. [2] in the form: where A = {Ps /PqJ1'2 has been referred to' as the "sulfurizing power' of a gas mixture. In this work, thin discs of CaO were suspended in a vertical tube furnace and exposed to CO + CO2 + SOz gas mixtures having known values of A. The samples were then analyzed for sulfur. As expected, X-ray diffraction confirmed that CaS was the only sulfur-bearing phase formed at the relatively low oxygen pressures used. EXPERIMENTAL PROCEDURE Reagent-grade CaCO3 was pressed in a 3/8-in.-diam pill die and prefired in air to produce CaO discs weighing between 0.004 and 0.01 g. Several discs were used to provide a suitable weight for chemical analysis while maintaining a large surface area to react with gas mixtures. These were placed in a platinum mesh basket and suspended in the gas stream in the hot zone of a vertical tube furnace. Desired gas mixtures were prepared from cp grade CO and CO2 and anhydrous grade SO2. The method of soap bubble displacement was used to calibrate capillary flow meters. While this gave excellent results with CO and Con, some problems with bubble insta- bility and soap film "drag" arose with the use of SO2 at low flow rates. Hence, frequent sampling and analysis of gas mixtures was carried out to insure proper control of the ingoing SOZ. The furnace used for gas:solid equilibration was a vertical mullite tube externally wound with 60 pct Pt-40 pct Rh wire having a diameter of 0.028 in. An inner tube of $ in. ID served as the reaction chamber having Pyrex ground joints sealed to the mullite to provide gas-tight connections at top and bottom. A Pt-Pt 10 pct Rh thermocouple was inserted into a protection tube adjacent to the sample basket to measure sample temperature during a run. Constant-temperature control to 2C was observed at any desired set point within the range of this investigation. This was accomplished by a control thermocouple imbedded in the furnace windings which served to actuate an electronic controller wired for high-low operation. The sulfur analyses of the solid samples were carried out using a stoichiometric combustion technique based on the method of Fincham and Richardson. Some analyses were done using a modified evolution method3 but these were used primarily to check the results of the combustion method. The results were in good agreement but the combustion technique of-ferred an advantage in economy of time and material. CALCULATION OF GAS EQUILIBRIA Heating a given mixture of CO + CO + SO2 to high temperatures gives rise to a large number of product species. The details of calculating the partial pressures of these products of interaction and dissociation can be found in several references4,5 and need not be repeated here. The thermodynamic data selected for the major species in the gas mixtures are shown in Table I. Equilibrium constants from these reactions were combined with oxygen, carbon, and sulfur balances and a computer program written to facilitate the calculations. Some early difficulties in reproducing experimental results were finally traced to the effect of atmospheric pressure changes. No reference to consideration of this question had been found in the

Jan 1, 1969

By I. R. Taylor

Union Carbide has recently developed two open- pit vanadium mines in the Wilson Srpings area of central Arkansas about five miles southeast of Hot Springs. The ores from these mines, together with those from a larger vanadium deposit at nearby Magnet Cove, are processed at a new 1600- tpd plant built by the company in the immediate vicinity (Fig. 1). The Wilson Springs vanadium deposits are associated with the Potash Sulfur Springs intrusive, a circular igneous complex which is exposed over an area that is somewhat less than a mile in diameter.1 The complex has a crude ring structure similar to that of the larger Magnet Cove instrusive six miles to the east.2

Jan 4, 1969

By F. T. Selleck, H. H. Reamer, B. H. Sage

An experimental investigation was made of the effect of temperature upon the three-phase pressure associated with the propane-water and propene-water systems when hydrates were present. In addition, the characteristics of the propane-propene-water system were established over a limited range of ternperatureo under conditions such that hydrate was formed. The hydrate phase for this system may he a solid solution and the distribution of propane and propene in it is similar to that found in the coexisting hvdrocarhon liquid phase. INTRODUCTION A knowledge of the characteristics of hydrates of the hydrocarborrs encountered in industrial practice is of importance in connection with the design of process equipment. Villardl.1,2 carried out early studies of hydrates, and de Forcrand1 con-sidered the more probable compositions of the hydrates of hydrocarbons. Hammerschnid1 presented information about the propane-water and the isobutane-water systems. Scheffer5 studied the hydrate of hydrogen sulfide in detail, and de For-crand reported on the hydrates of krypton, argon, and xenon.1 Roberts and co-workers1,2 determined the nature of the hydrates formed in the methane-water and ethane-water systems. Carson and Katz10 studied the methane-propane-water, methane-pentane-water, and the methane-hexane-water systems in the four-phase region. The results of this rather extensive investigation indicated that the paraffinic hydrates formed solid solutions. The experimental evidence now available does not Support the existence of hydrates of the pentanes-antl-heavier hydrocarhons but it cannot be stated with certainty that such hydrates are not formed. Stackelherg. 11,12,13 made extensive studies of the crystal structure of paraffinic hydrate; by means of x-ray techniques and found that hydrates poses; a definite structure and composition. The existence of such a Structure does not preclude the firmation of Solid solutions of hydrates in aqueous systems containing two or more hydro-carbon~. Wilcox, Carson and Katz" reviewrd the information on the hydrates of importance in the processing of natural gas and presented data concerning their formation from natural gas. Kobayashi and Katz1' made studies at high pressure of the Hydrate of methane. and Unruh and Katz"' investigated hy-drates in mixtures of carbon rlioxide and methane. Frost and Deaton contributed to the knowledge of the composition of the paraffinic hydrates The irregularities in the experimental results were several times the expected uncertainties. This experience confirms the behavior encountered by other investigators indicating that hydrates tend to occlude water during their formation, thus rendering difficult the direct measoremeut of their composition. Miller and Strong2 investigated a number. of paraffinic hydrates from the standpoint of their possible application to (, the industrial storage of gas. Powel1 studied the effect of solutes upon the decomposition temperature of paraffin hydrates. Marked lowering of the decomposition temperature at a given pressure may he obtained by the use of such additive agents as ethylene glycol, urea. and sodium chloride. APPARATUS AND METHODS Two method* were here employed to study the behavior of hydrates. The first involved a glass capillary within which the hydrocarbons and water were confined over mercury. The second made use of a double-ended weighing bomb technique." The glass capillary equipment has been described elsewhere.'" A schematic drawing of it is presented in Fig. 1, where the arrangement of the agitator and mercury reservoir is shown in some detail. The lower part of the glass capillary, D, was enlarged to afford space within which the fluids used in the investigation could he stored at low pressures after their introduction through the valve. G. The temperature of the capillary was controlled by the circulation of a hydrocarbon oil of low viscosity from the agitated bath, B, through the vacuum jacketed column. C. The pump, A, was employed for the circulation of this oil. A relatively clear view of the capillary tube, D, was obtained through the vacuum jacket. Mercury was introduced into the lower part of the vessel, E, from

Jan 1, 1952

By B. Ramaswami, Y. Nakada, U. F. Kocks

Compression tests were performed on single crystals of aluminum, silver, gold, and a Ag-10 pet Au alloy, with height-to-width ratios from 8:1 to 1:1. As this ratio decreased, so did the amount of easy glide until, for cubic specimens of all the pure materials, it was entirely absent. Heterogeneity of deformation is proposed to he a major contribution to the explanation of easy glide in slender specimens. For comparison, one single-crystal cube of zinc was tested and showed a behavior very similar to that in tension. Beyond easy glide, tension and compression curves are very similar. It is concluded that, in this range, neither grip effects nor orientation change influence the work-hardening characteristics to any significant extent. (121) and (100) crystals of all materials had similar stress-strain curves in tension and compression, except that the stress level of the flat portion of aluminum (109 crystals at high strains mas somewhat higher in compression. These results are at variance with previously proposed mechanisms of orientation dependence by both Hosford and Kocks. The compression tests themselves are described in detail and it is shown that they are essentially frictionless and produce single slip when the crystal is suitably oriented. DEFORMATION in uniaxial compression does not necessarily give the same result as deformation in uniaxial tension, essentially because the boundary conditions chosen are practically always different. 1) The shape and size of the specimens are usually different, and any genuine effect of size on work hardening should thus influence the result. 2) The grip constraints are usually different and can vary substantially for different kinds of tests. If the compression specimen is a thin plate and the friction on the platen is large, the grip contraints are more serious than in tension and lead, in the extreme, to uniaxial strain rather than uniaxial stress. If the specimen is roughly cubical and the friction is low, the specimen is less constrained than in tension inasmuch as displacements in the contact face are allowed. 3) The orientation change of single crystals is of opposite sign in tension and in compression; it is furthermore different in detail, because the relevant orientation in a squat specimen is the normal to the contact face, whereas that in a slender specimen is the generator of the side faces.' The considerable dependence of work hardening on the initial orientation in tension would suggest that the orientation change should also be very important. 4) Finally, localized deformation instabilities found in tension tests, such as necking and Lüders band propagation, are not possible in squat specimens. This is, for some investigations, a favorable consequence of the large grip influence. Even if one is not interested in any of the effects mentioned above, compression tests are often desirable just because the specimens needed are so much smaller and sturdier. For example, they have been very helpful in the investigation of latent hardening by means of alternate longitudinal and lateral compression of cubes,* and for testing

Jan 1, 1964

By John Johnston

WHEN I was honored by being invited to give the Howe Memorial Lecture, I decided to read Howe's book, "The Metallography of Steel and Cast Iron," published in 1916-that is, about 25 years ago-in search of a text. I found the book written in fine, clear, attractive, yet precise style, as I expected, knowing that his father ¬Dr. Samuel Gridley Howe, his mother-Julia Ward Howe, and all of his four brothers and sisters had lived in a New England literary atmosphere and had written books. This leads me to suggest that many authors of metallurgical papers and books could well study Howe's writings with a view to the improvement of their own. I failed to find a specific text, but did find a subject, for in reading his book I was struck by the few instances in which time is considered explicitly as a factor in the phenomena examined, and by the fact that many of the hottest arguments would have been settled had time been taken properly into account. Indeed, Howe hardly mentions time except in a rather incidental way, as in a few references to lag; for instance: The lowering of temperature at which the transformation occurs by rapid cooling . . . is a phenomenon of undercooling or lag. It is in part explained by the fact that the transformation itself is a time-consuming reaction which, setting in during a rapid fall of temperature. is naturally protracted till the temperature has sunk far below that at which it is due. He does discuss, quite fully, the iron-carbon equilibrium diagram, as known at that time, introducing it by stating: As he is a reasonable man who is not deterred from using a hand truck for moving his trunk by the consideration that he has thus to move a trunk plus a truck, so am I reasonable in putting into your hands this useful, indeed indispensable, tool for mastering the ABC of iron metallurgy. Somewhat later, in introducing a discussion of the phase rule, which "it would be hardly proper to pass . . . by without an attempt to outline its meaning," for "a clear exposition of its applicability or jurisdiction is needed to restrain the half-initiated from misusing it and the uninitiated from being misled by these misuses," he writes-and I quote his statement because we cannot properly discuss the influence of time on a process until we know the state of equilibrium which would ultimately be reached by the system under consideration It is a most remarkable and valuable generalization, its conceptions help greatly toward getting a broad outlook on metallography, but its misconception has brought out a flood of obscuring writings. It tells us about the constitution towards which alloys tend, that which they reach when equilibrium is complete, when all tendencies have corrected themselves and have been complied with completely. Its application, in absence of true equilibrium, is like determining density with a telescope or even with a tuning fork; it is like the mad tea party at which the butter put into the works "f the watch was the best butter. If the reader learns no more than to beware of attempts to decipher the conditions of inequilibrium by a law which touches only the conditions of exact

Jan 1, 1942

By J. C. Cook

In solution-mining of underground salt and similar minerals, using drilled wells for access, it is desirable to monitor the lateral growth pattern of the resulting fluid-filled cavern. Therefore, a process of seismic surveying from the surface of the ground has been conceived in which the amplitudes of waves reflected from and transmitted through the soluble formation are measured. The large acoustic impedance contrast between solid and fluid should produce striking amplitude anomalies, especially if shear waves are employed, since thick fluid bodies are opaque to shear waves. Horizontally-polarized (SH) shear waves are best for preventing conversion to P waves at the numerous horizontal interfaces in the ground. Field tests to date have shown that a truck-mounted, half-ton hammer striking horizontally against the end of a trench produces usable SH-wave energy at lateral distances up to about 850 ft. Horizontally-directed explosive wave sources were effective to about 2000 ft. Conventional magnetic-tape recording and processing were used, but with the detecting geophones oriented to favor SH waves. An irregular solution cavity in bedded salt at 500-ft depth has apparently been located by SH-wave and SV-wave reflections. Further field work is planned to corroborate and extend this result. The Brine Cavity Research Group, an association of 11 chemical and salt producing companies, is supporting this work. Major deposits of salt in tabular beds lie beneath some 300,000 sq miles of land in the central and northeastern U.S. This salt is a basic source of soda ash and chlorine, and has been extracted as brine from drilled wells for about a century. During the past two decades, the U.S. solution-mining industry, following the lead of European operators, has greatly improved the extraction process through the application of engineering and science.' In 1957, the Brine Cavity Research Group, an association of 11 chemical and salt producing companies, was formed. This group proceeded to attack certain common problems through the support of research. An outstanding problem has been that of determining the shape and location of the growing solution cavities in the underground salt, so that measures can be taken to maintain operating efficiency. The problem has been partially solved by the Dowel1 sonar mapping service, which employs a pulse-echo device lowered into the cavity through the well.2 However, the working range of this equipment is at present insufficient for large cavities, and echoes are not returned from highly sloping walls nor from behind such obstructions as rock debris. Therefore, an independent means of mapping the cavity, for example, from the surface without interfering with operation of the well, would be desirable. THEORY OF THE METHOD Seismic waves are the only physical agent known to be capable of sufficient resolution and penetration to define typical solution cavities from the surface of the ground. The geometry is unfavorable: cavity widths are generally less than half their depths below the surface; resolution and lateral location of boundaries and channels to within 50 ft at depths of 500 to 3000 ft is desirable. Conventional seismic surveying, as used for petroleum prospecting, is probably not the answer: isopach mapping, for example, is not thought accurate enough to define the cavity by the slight additional delay time it would introduce (of the order of 0.005 sec for a 50 ft-thick cavity in hard Paleozoic rocks). Refraction surveying has also been considered, but seismic specialists see little promise in it for this problem. In 1957, in correspondence with industry personnel, the writer suggested a seismic method based upon careful measurement of reflection amplitudes. As Table I illustrates, seismic reflection coefficients r for typical brine-rock interfaces are considerably higher than those for typical interfaces between different kinds of solid rock. This fact can be utilized in two ways, illustrated in Fig. 1: 1) If the cavity roof is reasonably flat (which it may sometimes be since the unsaturated top brine will be in contact with an insoluble rock stratum), extra-strong seismic reflections will be received from the salt stratum where the solid has been replaced by liquid.

Jan 1, 1964

By Nathaniel Arbiter

THE separation of minerals by flotation can be regarded as a rate process, with the extraction of any one mineral determined by its flotation rate, and the grade of concentrate by the relative rates for all the minerals. So regarded, the significant variables for the process are those that control the rates. These variables are of two types, the first describing the ore and its physical and chemical treatment prior to flotation and the second characterizing the separation process in the cells. This paper will examine the variation in rates for a group of separations, will show that a simple rate law appears to govern, and will consider the relation of the control variables to the rates. The use of rate constants for evaluation of performance and efficiency will be discussed. Flotation involves the selective levitation of mineral and its transfer from cell to launder. The flotation rate is the rate of this transfer. It may be defined by the slope of a recovery-time curve for any cell in a bank, or at any time in batch operation. The objective in flotation rate study is an equation expressing the rate in terms of some measurable property of the pulp. This can be either the concentration of floatable mineral in weight per unit volume1,2 or a relative concentration, which will be a function of the recovery." A rate equation for an actual flotation pulp will contain at least two constants, both to be determined from the data. One of these, the initial concentration or proportion of floatable mineral, is not necessarily equal to the feed assay because of nonfloatable oversize or locked particles." The other, a rate constant, is a measure of proportionality between the rate and the pulp property on which the rate depends. The value of the rate constant will be determined by the values of all variables which control the process and will be changed by significant changes in any of them. It is, therefore, a direct measure of performance. Where recovery or grade change continuously with flotation time, the rate constant will be independent of time and will characterize the entire course of the separation. Development of Rate Equations Rate equations can be developed either by analysis of the mechanism of the process or by direct fitting of equations to recovery-time data. Sutherland's attempt by the first method' suggests that the effect of particle size variation on the rate complicates the derivation of a simple equation applicable to an ore pulp. A further problem with an ore is the concentrate grade requirement, which usually involves a variable rate of froth removal. Thus the final rate for any cell may depend on the froth character and froth height, as well as on the pulp composition. This does not imply that each cell cannot reach a steady state2 in which the rate will depend ultimately on pulp composition. The second method is the fitting of rate equations consistent with the necessary boundary conditions* to experimental recovery-time curves. On the assumption that under constant operating conditions the flotation rate is proportional to the actual or relative concentration of floatable mineral in the pulp, a generalized rate equation may be expressed as follows: Rate = Kcn [I] where K is the rate constant, c is some measure of the quantity of floatable mineral in the pulp at time t, and n is a positive number. In previous rate studies, the value of n has been taken as 1, either by direct assumption," or as a result of the hypothesis that bubble-particle collision is rate determining.' A first order equation results, which after integration in terms of cumulative recovery R, leads to Loge A/A-R = Kt [2] The quantity A is the maximum possible recovery with prolonged time under the conditions used. No conclusive proof for the validity of this equation in flotation has been advanced. The evidence cited in its support consists entirely in the demonstration that it appears to apply to a limited number of recovery-time curves."' It will be shown subsequently that this procedure is not sufficient to establish the order of a flotation rate equation. The possibility that the equation may be of higher order therefore requires examination. If, in particular, the exponent in eq 1 is assumed to be 2, then after integration there results R = A2Kt/1 + AKt [3] with K again a rate constant and A the maximum proportion of recoverable mineral. Eq 3 may be

Jan 1, 1952