Search Documents

For the use of future students the following notes on the times of completion of various railroads and canals supplying transportation to coal fields are set down. These dates are widely scattered and sometimes difficult to find. A statement showing the mileage of railroad building from 1830 to 1879 by each railroad in the United States is given in the 10th U. S. Census, 1880, vol. 4, pp. 318-365. [Date of Opening Various Bituminous Districts by Railroad Transportation1 Blossburg, Pa. district in1840 Georges Creek, Md. district in1842 Broadtop, Pa. district in1856 Clearfield, Pa. district in1866 Meyersdale, Pa. district in1872 C. & 0., W. Va. district in1873 Elk Garden, W. Va. district in1881 Pocahontas, Va. & W. Va. district in1883 Beech Creek, Pa. district in1884 Hocking Valley, 0. district in 1869.-by Canal 1840] See also Paullin's Atlas of the Historical Geography of the U. S., published by the Carnegie Institution of Washington, 1932, for small-scale maps showing railroad development by decades. [OHIO CANALS Date Date CompletedName of CanalFromToAbandoned 1827, July 4Akron Cleveland 1827, Nov. 28Cincinnati Middleton 1828, Dec. 31 Cincinnati Sandusky 1830, July 10 Cleveland Newark 1832, Dec. 31 Akron Portsmouth 1838Penna. & Ohio Akron Pa. Canals 1853 north of Pgh. 1840, Sept. Hocking Valley Columbus Nelsonville 1844 Sandusky Dayton 1846 Sandy & Beaver Bolivar Smith's Ferry 1852 1846 Cincinnati Springfield]

Jan 1, 1942

By Norman Ketzlach

ANGANESE today overshadows all strategic materials in our planning for national se-curity," according to a report issued recently by the American Manganese Producers Association. By far the greater part of the manganese ore used in the United States is imported. "We have enough manganese ore in the United States to last from one hundred to three hundred years and longer, but most of the deposits are undeveloped. As in the case of copper, lead, and zinc, manganese ore, both foreign and domestic are low grade. Manganese ores have to be concentrated and processed. After being processed, domestic ores are higher grade than foreign." Most of the manganese ore found in this country, however, is not amenable to concentration by ore-dressing methods. Manganese Products, Inc. has developed a sulphurous-sulphuric acid leaching process for the recovery of manganese from low-grade, intermediate manganese ores. By the term "intermediate manganese ores" is meant those ores in which the manganese in the form of manganese oxides is found to have two different valences, usually two and four, as is probable in Mn,O, or the ore may be a mixture of manganous and manganic oxides. "Intermediate" manganese siliceous ores are ores in which the silica is a constituent of the ore and is loosely linked to the manganese by water of crystallization. This process has been carried out with the type of manganese ore found in the Olympic Peninsula of western Washington; Clough, N. C.; and Lava Hot Springs, Idaho, as well as just recently with manganese ore from Las Vegas, Nev. As far as the manganese leaching process is concerned, these ores differ primarily in the form in which the manganese oxides occur. The tetravalent manganese, the manganese existing in the dioxide form, is soluble in a sulphurous acid solution. To dissolve the divalent manganese, sulphuric acid is required. To dissolve the type of ore found in Washington and North Carolina, a mixture of both sulphurous and sulphuric acid is used. Whereas to dissolve the type of manganese ore found in Idaho and also in Montana, sulphurous acid alone is sufficient. The Nevada manganese ore is of the same type as that found in Idaho as far as the leaching process is concerned. It has long been known that manganese ores, with the exception of rhodonite, which is a true manganese silicate ore, can be dissolved readily in sulphurous and sulphuric acids.' The removal of the impurities such as silica, iron, and alumina from the resulting solution is the step that has been difficult. The process worked out by Manganese Products has been carried through pilot-plant equipment. This process has also been extended to the production of ammonium sulphate. Leaching of Ore: The manganese ore, ground to —-65 mesh is leached with sulphurous acid and sul-

Jan 1, 1951

By A. Kenneth Schellinger, O. Cutler Shepard

Overgrinding, Or the breaking of ore particles into sizes smaller than required for liberation, is a first-magnitude problem in grinding for concentration processes. The conventional ball mill-classifier circuit used in commercial grinding produces mineral particles that are all ground to pass an upper size limit, while the proportion of very fine sizes, or slimes, is uncon rolled. Calculations based on measurements made in commercial plants which were grinding ore for flotation concentration indicate that about go pct of the energy used in grinding is consumed in useless overgrinding.1 In addition to accounting for the consumption of a large amount of energy, over-grinding is detrimental to the flotation process. Overground slime coats larger partitles and inhibits selective action by the flotation reagents on particles which by themselves could be separated very well. A further difficulty is that extremely finely ground minerals do not respond satisfactorily to flotation-collecting reagents, and both selection and recovery decrease markedly with particles finer than 5 to 10 microns.2 conventional classifier-ball mill circuits inherently tend to overgrind the valuable minerals more than the gangue minerals because most valuable minerals are of higher density and are softer and more friable than the gangue minerals. The rem- edy to this situation would seem to be a separating mechanism which would separate free valuable mineral particles regardless of size and density considerations and a mechanism which would operate in the grinding mill so that valuable mineral grains would be removed from the grinding machine as soon as they are freed. A consideration of these ideas led the authors to the conception of a simultaneous grinding and flotation mechanism. So far as the authors are aware, such a machine has never been tried, even on a laboratory scale. Development oF Apparatus and Experimental Method Apparatus development went through several stages before a really workable machine was devised. Work was started with a large cast-iron mortar 7½ in. in diameter and 8 in- deep. A cast-iron disk Was mounted on the end of a vertical shaft SO that it fitted loosely into the bottom of the mortar. On top of the disk four radial cleats ¼ in. high were bolted to agitate the ball charge as the disk, or impeller, rotated. The vertical shaft was driven at 100 rpm by a mechanism improvised from an old coffee-mill type of grinder. A hole was drilled into the bottom of the mortar through which compressed air was introduced for frothing. In operation, more charges of Ore which had been crushed to pass an 8-mesh screen were placed in the bowl along with water and suitable reagents. The impeller was then started and the compressed air turned On so that the ore was ground while being exposed to air bubbles. Mineralized froth was

Jan 1, 1949

By David P. Hale

THE Cartersville barite district is near Cartersville, Ga., in the southeastern part of Bartow County, about 43 miles northeast of Atlanta. The area over which active mining is being done extends about six miles in a northeasterly direction and is about three miles wide. Barite production in Georgia began about 1907,1but the existence of the mineral was known much earlier. At present four companies are operating washing plants and three other plants are operating on leases from those companies. The chief impurities in the ores are silica and iron oxide. The silica is easily washed and jigged out and gives little trouble. Any gravity separation between the iron and the barite is generally poor, owing to the slight difference in specific gravity. Two operators have turned to magnetic separation as the solution to the problem and have made remarkable improvements in the finished product. By very close sizing prior to jigging, the separation between iron and barite has been greatly improved. In some localities manganese occasionally appears as an impurity, but is fairly easy to eliminate by gravity methods. A considerable percentage of iron and silica is eliminated by being broken free in crushing. Until methods for the recovery of fine ore were introduced a minimum of crushing was done, but modern methods allow more than formerly. The depression years brought about the need for increased recovery of ore handled on the part of the producers and a demand for a higher grade of product on the part of the buyers. Improvements in milling and mining practice have had a far greater effect, however, than merely the production of a better grade of ore with greater recovery. They have opened for mining large areas that a few years ago were considered noncommercial deposits because of their inaccessibility and their high iron content. It is no exaggeration to say that the new methods have more than doubled present known reserves of barite ore of economic value.

Jan 1, 1938

By Eugene McAuliffe

TWO years ago the American Institute of Mining and Metallurgical Engineers made a memorable contribution toward a better understanding of the problems that have for many years confronted the coal industry. Specific suggestions toward betterment were then advanced, certain of which were taken up, amplified and endorsed by men who were conscien-tiously interested in the work of lifting this great industry out of the morass it has lain in for years. Two certain suggestions then made-provision for seasonal variations in railroad freight rates that would tend to encourage the purchase and movement of coal during the low summer production period, and provi-sion for the collection by the United States Government of all the facts surrounding the industry-were intro-duced in the form of legislation in the United States Senate by a member of that body, a man whose personal character, antecedents and business training put him above and beyond all suspicion of demagoguery; however, as the result of the insistent, vindictive opposition of the industry itself, these two bills, con-structive in their nature, were buried under an ava-lanche of misrepresentation. Today, with all mines that employ union labor at a stand still, the work of stabilizing the industry is yet before us. As aptly stated by Herbert Hoover, in March, 1920, when he was president of the Institute; An engineering organization is particularly the body to under-take this work. It is an economic problem, an engineering pro-blem within the ken of our experience; it is a problem that requires not only constructive thought but quantitative thought and wise social thought. The engineers of the United States occupy a position midway between capital and labor. They enter upon problems of this kind without prejudice either way, and they have that faculty of mind for quantitative thought, as distinguished from qualitative thought, that takes such problems as this out of the region of politics into the region of matter-of-fact solution.

Jan 5, 1922

By William S. Hannan, H. Rush Spedden

FLOTATION may be defined as a process whereby mineral particles are concentrated by selective adhesion to air-liquid interfaces. The process involves attachment of desired mineral particles to air bubbles, and removal of the mineralized air bubbles from the surface of the pulp as a mineral concentrate. PROBLEM Although great strides have been made in understanding the principles of flotation, one part of the process which has not been adequately explained is the mechanism by which selected mineral particles become attached to air bubbles. A glance at the froth of an operating flotation cell demonstrates adequately that use of proper reagents and conditions will result in such attachments; but how such attachment takes place is not definitely known. A better knowledge of this factor might lead to improved flotation practice either through altered machine design or the application of scientific innovations. Direct observation of the behavior of mineral particles and bubbles in an operating cell does not appear promising because of the complexity of the system. For this reason, conclusions concerning the problem must be deduced from theoretical considerations or from observation of simplified systems designed to reproduce conditions thought to exist in an operating cell. PRESENT THEORIES Two mechanisms have been recognized as fundamental in particle-bubble attachment: gas precipitation and direct encounter. It is a simple matter to demonstrate in the laboratory that attachment can be brought about by either mechanism. As to the relative importance of the two in a particular flotation system, however, there is a divergence of views. Taggart1 states, Under exceptional circumstances sufficient force and time to effect attachment may conjoin in an ore pulp undergoing agitation, and a preformed bubble adhere to a collector-coated mineral particle, but the occurrence is rare. . . . Pulp-body froth flotation effects selection in the body of a conditioned pulp by causing gas bubbles to precipitate from solution in the liquid phase preferentially at the surfaces of collector-coated particles, and to cling to these particles. Gaudin2 states that, within the pulp body of an agitation machine, attachment of mineral particles to air bubbles occurs as a consequence of contact between the two. This theory has been supported by theoretical reasoning and much circumstantial evidence. Perhaps the most interesting bit of evidence in favor of this theory is the difficulty in the flotation of fines. If attach-

Jan 1, 1947

By Walter Miller

Hundred-octane aviation gasoiine, toluene for T.N.T. production, high-quality lubricating oils for the needs of aviation and the armed forces, and synthetic chemicals for rubber manufacture again commanded the top priorities of the petroleum refining industry in 1944, the third year of America's active participation in the war. The objective continued to be to produce more and more of these materials—to keep up with increasingly greater requirements. By the end of the year all of the new installations projected before 1944, with the exception of possibly two or three that will tail over into January or February of 1945, had been completed and put into operation. And with the completion and putting into operation of these various units and the consequent lessening of construction responsibilities and problems, the industry was put into position to concentrate on the new operations and devote much more of its time and effort looking toward maximum output, both as to quantity and quality from the new facilities. Aviation Gasoline Making high-octane aviation gasoline continued to be the prime requisite of refining activities during 1944 as it was in the two previous war years, with the sights at the end of the year set to still higher figures than those which had been previously projected. About July I the daily output had been raised to 400,000 bbl., with some few large plant installations still to be completed and put into operation. Indications were that by December production would be up to all requirements, with good inventories. However, although by the end of the year the industry was turning out something over 500,000 bbl. a day, the estimated requirements of the armed services had been raised by a considerable figure, owing to the greatly increased aerial activities both in the European and Far Eastern combat areas. By the end of the year, therefore, the picture had changed, with the prospect for a much longer continuation of the European war, so that even with the completion and putting into operation in the United States by January 1945 of the last two or three 100-octane units authorized prior to 1944, it was evident it would be necessary to make still greater efforts to increase output of existing facilities to keep safely ahead of the game. Efforts of the industry and the Petroleum Administration for War as well as the Technical Advisory Committee and other research and development groups are concentrated therefore on methods and means of further augmenting the produc. tion of all existing refinery facilities engaged in making 100-octane aviation gasoline and components entering into it. The goal will be reached.

Jan 1, 1945

By Edward C. J. Urban

THE nature of certain pernicious dusts commonly encountered in the removal of iron ore from the underground mines of the Lake Superior district is recognized, and appropriate measures for the protection of individuals subjected to these dusts have been applied in most mines for more than to years. Undoubtedly the principal concern has been demanded by dusts that contain as a constituent silicon dioxide in its free or uncombined state, the mineral we all know as quartz or chert. Investigators1 agree that among the factors that determine injurious exposure are: the composition of the dust, the concentration suspended at the breathing level and the duration of the exposure. We have on hand data that describe the experience of several underground iron-ore mines in the Upper Peninsula of Michigan and Wisconsin in regard to these factors, which in a large measure also reflect the general experience of the other mines of the area. We believe that a discussion of these data will indicate the effectiveness of the dust-control methods that have been considered good practice and that have been employed over a long period of time. A silicosis-prevention program was ini¬tiated by the iron mines of the Upper Peninsula in 1934 and records of mine dustiness are available from that date to the present time. For dust conditions previous to 1934 the results of observations conducted in other industries can be utilized together with local information pertaining to the development and initial application of rock-drilling equipment. DEVELOPMENT OF ROCK DRILLS The earliest percussion rock drill that later had any industrial use was patented in this country in 1851.2 This machine was later modified and improved in many respects but its piston-type design remained standard for drilling equipment in most mines for the next 63 years.3 The piston drill was operated either by air or by steam. It employed a solid drill steel, fastened directly to the reciprocating piston. The drilling was done dry except in holes directed at an angle below the horizontal. For these water was manually injected into the hole and the pumping action of the rod expelled the sludge. The dry cuttings from drillings inclined above the horizontal fell from the hole by their own weight. A development of major importance from the standpoint of dust generation and control occurred with the invention by J. G. Leyner of a hammer-type rock drill that embodied the essential feature of a drill steel with a hollow core. His patent was secured in 1897. The machine was a radical departure in drilling method. The steel was held loosely in a chuck while

Jan 1, 1947

By A. C. Veatch

Jan 1, 1921

By J. E. Lamar

THAT Illinois is an important mineral producing state is well known. A value of over $237,000,000 for the mineral products in 1926 indicates the magnitude of the industries. Coal mining is the largest mineral industry, and the value of its product was about 63 per cent of the total mineral production of the state. Oil and gas constituted about 8 per cent and the non-metallic minerals about 29 per cent. This 29 per cent represents the production of a varied group of mineral industries of wide geographic distribution through the state.

Jan 1, 1929

By Sam Tour

OF the new alloys achieving commercial prominence during the year, an aluminum-silicon magnesium casting alloy, which is similar in many respects to the 4 per cent copper alloy, developed about 1921, which has attained such a wide field of service, may be mentioned. The new alloy, like the old, is a heat-treatable type and develops about the same physical properties. The alloy casts easily and is relatively insensitive to high pouring temperatures. Its ability to produce substantially leak- proof castings is noteworthy. A second casting alloy development is the new Aluminum Co. of America No. 132, "Lo-Ex" piston alloy, a result of nearly eight years of research. The alloy contains about 14 per cent silicon and varying amounts of nickel, copper, and magnesium. It exhibits a low coefficient of expansion and thus permits small piston clearances. Its lower specific gravity is a further advantage.

Jan 1, 1932

By Roger L. Goin

Maintaining smooth haulage roads is a key to significant cost savings at Kennecott Copper Corp.'s Bing- ham Canyon copper mine, located near Salt Lake City, Utah. The truck operations section of the mine moves an estimated 300,000 tpd of waste plus some ore to maintain a balanced production cycle. A three-year truck replacement program has produced a dramatic new look in both size and capacity of the truck fleet. Currently there are 95 haulage trucks in the Bingham fleet with capacities up to 150 t. The trend towards the larger haulage units places greater importance on overall truck availability. The impact of a 150-t truck being out of service is far more critical than with the former 65 or 85-t units.

Jan 12, 1974

By Bryon W. Cheever

The greatest objection to be brought against the present methods for estimating phosphorus in iron and steel, is the time consumed in the operation. The following method, originated and perfected by Mr. E. D. Campbell, assistant in the chemical laboratory of the University of Michigan, will, 1 think, if carefully followed out, give results that are sufficiently accurate for technical purposes, and will give them in less time than they can be obtained by any other process. The process consists in comparing the color obtained by the action of stannous chloride upon a solution of the phospho-molybdate precipitate obtained from the solution of iron or steel, with that obtained from a standard solution of molybdie acid which represents a given amount of phosphorus. The operation is as follows : Take of ordinary steel 1 grm. and treat as in any of the wellknown processes until the phosphorus is precipitated as ammoniumphospho-molybdate. When precipitated, the phospho-molybdate precipitate is filtered out, thoroughly washed with an acid solution of ammonium nitrate, and, finally, twice with water, to remove most of the ammonium nitrate. The precipitate is then dissolved in about 1 c. c. of 10 per cent. potassium hydrate, which is let fall drop by drop on the filter till the precipitate is dissolved ; the filter is now washed with about 25 or 30 c. c. of water, and the potassium hydrate solution, which now consists of 25-32 c. c. of solution, is boiled until the peculiar frothy appearance, which first appears on boiling, is entirely gone. The solution is then cooled until perfectly cold, and about 10 or 15 c. c. of strong hydrochloric acid added ; if the solution is kept cold this will form no precipitate, but a light yellow or colorless solution. The solution is now ready for the addition of stannous chloride, and the subsequent comparison of color produced with that obtained from the standard molybdie acid. The comparison is made in tubes that are calibrated like carbon-tubes, but which are larger, about 5/8-inch bore, and graduated to 100 c. c.; this makes them about 18 inches long. To make the comparison of color, first transfer the now acid solu

Jan 1, 1886

By E. H. Kelton, R. D. Grissinger

In designing structural members of steel and some other materials the design engineer has available recognized values of elastic modulus and safe working stress that may be substituted in well-known engineering formulas to give him desired cross-sectional areas and deflections for a particular part. Zinc, on the other hand, has no generally recognized modulus. It flows under continuously applied loads. Therefore, the designer of structural members must use a range of working stresses depending on the continuous load and the amount of permissible distortion. The only method of obtaining these values is by creep testing. Creep testing of zinc has been carried on for some 20 years by this laboratory, covering a wide range of zinc and zinc alloys. Types of test included tension, compression, and simple and cantilever beams at temperatures ranging from o to I50°C. Specimen conditions ranged from as-cast or as-rolled to accelerated aged in steam or dry air. Effects of plating were investigated also. It is not the intention of this paper to expound all these factors but rather to present the final data on well-known zinc die-casting alloys and to suggest means of applying these data to engineering design. Early Work In the early work on creep testing of zinc, the direct-loading tension method was used. However, direct loading of die castings was unsatisfactory because of the high loads required. For instance, a standard die-cast tension bar having a cross-sectional area of about 0.049 sq. in. would require a direct load of about 1000 lb. for a unit stress of 20,000 lb. per sq. in. Also, tests were made at nominal room temperature, but normal variations caused fluctuations greater than those due to experimental error or other causes, so that control of this variable within ±1/2°C. seemed essential. These two factors led to the development of an apparatus described by J. Ruzicka,' in which the specimens were loaded by means of a lever and were held at constant temperature by means of an oil bath. While Ruzicka's apparatus yielded excellent check results, it seemed desirable to have some setup by which literally hundreds of die-cast specimens could be tested at the same time. This would permit the conducting of a number of low-load tests designed to run 10 years or longer and still leave capacity for current high-load work. Beam testing in a constant-temperature room was the answer. Test Method Preliminary work indicated that die-cast beams of various lengths and cross scctions yielded the same result within reasonable limits regardless of whether they were tested as simple beams, uniformly loaded beams, or cantilevers. Accordingly, the simplest type was adopted. This was a,

Jan 1, 1945

By William T. Schneider, Taylor Cole

Drilling in West Texas during 1941 was more active than in any year since 1937, a total of 2325 wells having been drilled. Pre-Permian exploration was the greatest in the history of the area; 106 wells tested pre-Permian formations during the year. Wildcatting reached the peak since 1937, with 135 wildcats, of which 20 per cent were producers. The wells were drilled to a greater average depth than in any previous year. Slim-hole drilling was the common practice, using drilling equipment that is largely portable. Because of deeper drilling, more attention was paid to mud fluids, especially the use of materials to reduce water filtration. There has been slight improvement in the protection of the pay horizons while drilling by the use of reverse circulation, and drilling-in with oil as well as low water-filtration muds. The practice of setting and cementing the oil strings through the producing formation and perforating opposite the pay zones has increased in the fields producing from sands. It is doubtful whether this practice is of unusual value in dolomitic limestone fields. There have been few if any technological improvements in obtaining necessary information on the pay sections penetrated, by coring, core analyses, better sampling, and more detailed drilling time. However, more operators are beginning to realize the necessity of good samples. For a proper study of the reservoirs in West Texas, it is essential that better samples be obtained, that more core analyses be run, and that better methods of obtaining drilling time be initiated. It should be noted that increased drilling speeds and slim-hole drilling have tended to reduce coring and core recovery and have not aided in obtaining good subsurface samples. In fact, fast drilling speeds and slim-hole drilling have reduced the cost of drilling operations, but with the sacrifice of much needed subsurface information. Larger quantities of slower-reacting acid are being used per well. There has been improvement in shooting, in that a greater number of quarts per foot have been used and an attempt has been made to concentrate the shots opposite the pay zone. The use of mud logging to determine the characteristics of the pay section increased considerably over the year 1940. There has been a slight increase in obtaining reservoir information in the new fields, such as bottom-hole sampling, bottom-hole pressures, and records of gas, oil, and water withdrawals. However, there is great need for more data on these subjects, particularly accurate information regarding gas and water volumes. There are three repressuring projects and a fourth is nearly ready for operation in the Kermit field. There is one repressur-ing project in the Payton field and one in the North Ward field. So far, the gas-injection projects have not shown very impressive results. As yet, there are no water-flooding projects or water-disposal projects in West Texas. Not including gathering lines within the fields, 222 miles of feeder pipe lines were

Jan 1, 1942

By Fred C. Bond

THEM is acute need for a method that will measure the size distribution of finely divided materials, particularly when the particle sizes are smaller than the openings of the finest screen cloth regularly available for testing. Several methods and types of apparatus are in common use, but none are entirely satisfactory for all purposes. The commonest methods are microscopic grain counts, elutriation by liquids or air, and sedimentation. Valuable results have been secured by air elutriating devices, typified by the Haultain Infra-Sizer and the Pearson Air Analyzer. These are especially useful in obtaining sized fractions that can be examined and analyzed separately. They are particularly advantageous because the sizes of the samples produced are adequate for a considerable amount of subsequent manipulation and testing. The sedimentation methods, such as the Wagner and Klein turbidimeters, and the sedimentation balance, do not deliver sized fractions, but they do provide a means for reasonably rapid comparative determinations of fineness and surface area, which are important in many industries. The sedimentation balance consists essentially of a balance pan suspended in a liquid that contains falling particles. These are weighed as they settle onto the pan, and the time rate of settling is determined. The size distribution is computed from the settling rate. The balance appears to be inherently more accurate than any of the other methods, and it has served a useful purpose in the study of numerous problems, but there have been limitations which have restricted its scope of application. Because of the essential simplicity of the method, it was felt that intensive investigation might lead to modifications that would make it a valuable tool for the operators in industries that require precise information regarding the results secured from grinding equipment. A large number of size-distribution determinations below 200 mesh were required in connection with a particular research problem in fine grinding. The sedimentation balance was used in this investigation, and a technique was gradually developed that ultimately gave good results. A serious difficulty appeared early in the work. It was discovered that less material always settled on the sedimentation pan and more on the bottom of the containing jar than could be accounted for by calculation, and also that the material that settled to the bottom of the jar outside the edges of the pan was considerably finer than that on the pan. This segregation was so great that the distribution obtained for the finer sizes was obviously very much in error; material ground to about the degree of comminution of cement might have only 60 per cent of the calculated weight actually settling on the pan, and the error increased with the fine-

Jan 1, 1939

By A. M. Gaudin

The flotation process has been applied extensively in the mineral and chemical fields. This paper reveals results obtained by an exploration of an application to the biological field. In many ways this study was indeed an exploration since so many factors are different. In the mineral field, the particles, both those floated and those not floated, cover a wide range of sizes and shapes; in the biological field, the particles of one population are primarily of one or two sizes and one or two shapes. This identity in size and in shape gives biological systems the advantage of homogeneity. In the mineral field the particles may be as coarse as a millimeter; in the biological field the size may be a micron, or less. In the mineral field the particles may have a gravity several times that of water so that their apparent gravity is quite substantial. Microorganisms, on the other hand, may have a gravity so near that of the liquor that their settling velocity in the liquor is vanishingly small. These two facts conspire to make bubble-particle encounter in the pulp-body less likely. Finally, microorganisms are living, reproducing, and dying-all of which does not help the experimenter get a balance of materials. The analytical problems, too, are extraordinarily difficult, for the organisms can contain only elements that occur in their environment, although at a different level of concentration. The chemical composition of the surface of microorganisms is readily altered. In spite of these areas of difficulty, microorganisms can be floated to leave practically water-clear tailing, they can be floated from each other and, in fact, the same organism can be fractionated into a float that differs from the sink. SIZES AND SHAPES OF ORGANISMS Most ore pulps are described with reference to the percentage of the pulp that is fine enough to pass a 200-mesh sieve. Thus a copper-ore pulp may be 80% -200 mesh. Since 200 mesh equals 74 µ, a 2000-mesh particle would be 7.4 µ in diameter, and a 20,000-mesh particle would be 0.74 µ. The microorganisms with which this work is concerned are of the order of magnitude of 20,000 mesh. We have worked with Escherichia coli, the colon bacillus, Bacillus cereus, Bacillus subtilis, Bacillus megaterium, and Serratia marcescens. In some pioneer work, Dognonl,2 reported the use

Jan 1, 1962

By Taylor Cole, William T. Schneider

Drilling in West Texas during 1941 was more active than in any year since 1937, a total of 2325 wells having been drilled. Pre-Permian exploration was the greatest in the history of the area; 106 wells tested pre-Permian formations during the year. Wildcatting reached the peak since 1937, with 135 wildcats, of which 20 per cent were producers. The wells were drilled to a greater average depth than in any previous year. Slim-hole drilling was the common practice, using drilling equipment that is largely portable. Because of deeper drilling, more attention was paid to mud fluids, especially the use of materials to reduce water filtration. There has been slight improvement in the protection of the pay horizons while drilling by the use of reverse circulation, and drilling-in with oil as well as low water-filtration muds. The practice of setting and cementing the oil strings through the producing formation and perforating opposite the pay zones has increased in the fields producing from sands. It is doubtful whether this practice is of unusual value in dolomitic limestone fields. There have been few if any technological improvements in obtaining necessary information on the pay sections penetrated, by coring, core analyses, better sampling, and more detailed drilling time. However, more operators are beginning to realize the necessity of good samples. For a proper study of the reservoirs in West Texas, it is essential that better samples be obtained, that more core analyses be run, and that better methods of obtaining drilling time be initiated. It should be noted that increased drilling speeds and slim-hole drilling have tended to reduce coring and core recovery and have not aided in obtaining good subsurface samples. In fact, fast drilling speeds and slim-hole drilling have reduced the cost of drilling operations, but with the sacrifice of much needed subsurface information. Larger quantities of slower-reacting acid are being used per well. There has been improvement in shooting, in that a greater number of quarts per foot have been used and an attempt has been made to concentrate the shots opposite the pay zone. The use of mud logging to determine the characteristics of the pay section increased considerably over the year 1940. There has been a slight increase in obtaining reservoir information in the new fields, such as bottom-hole sampling, bottom-hole pressures, and records of gas, oil, and water withdrawals. However, there is great need for more data on these subjects, particularly accurate information regarding gas and water volumes. There are three repressuring projects and a fourth is nearly ready for operation in the Kermit field. There is one repressur-ing project in the Payton field and one in the North Ward field. So far, the gas-injection projects have not shown very impressive results. As yet, there are no water-flooding projects or water-disposal projects in West Texas. Not including gathering lines within the fields, 222 miles of feeder pipe lines were

Jan 1, 1942

By John M. Kelly

New Mexico produced 39,475,388 bbl. of oil in 1944, the greatest amount in one year in the oil history of the state. This production was 593,046 bbl. or 1.25 per cent more than in 1943. New Mexico retained its position as the seventh largest oil-producing state. The maximum per well allowable on Jan. I, 1944 was 48 bbl. daily and at the end of the year it was 45 bbl. daily. Allocations as set by the New Mexico Oil Conservation Commission closely followed the recommendations made by the' Petroleum Administrator for War. The average daily pipe-line runs were within 4 per cent of the allocation. Production by counties was as fol1ows;Lea County, 33,509,548 bbl.; Eddy County, 5,504,498; Northwestern New Mexico 461, 342. Drilling activity for New Mexico in 1944 was well above that of 1943, with 362 completions. Of these, 283 were oil wells, 12 gas wells and 67 dry holes. The ratio of dry holes to producers, about I to 4, was an improvement over 1943. Wildcat drilling during 1944 was responsible for the discovery of six new fields and the extension of two present producing areas. Drilling records were established in New Mexico during 1944 with the deepest producer ever completed, the Humble Leonard Oil Company's No. I at 11,969 ft., in the Ellenburger section of Ordovician age near Jal, Lea County. The discoveries in Lea County during 1944 were as follows: West Lovington field, where Fred Turner, Jr. drilled his No. I State B .in C SE SW sec. 4-17-36 and completed it for 122 bbl. of oil in 8 1/2 hr., in the San Andreas section of Permian age. The Tonto field, where the T-exas Company completed its No. I Baskin at a total depth of 3586 ft. in Seven Rivers lime of Permian age, with an initial production of 254 bbl. of oil in 21 hours. The Drinkard area, where the Gulf Oil Corporation's Drinkard No. I flowed 782 bbl. of oil in 14 hr. from the Yeso section of lower Permian age, thus opening the first lower Permian production in the state. The total depth of this discovery was 6508 ft. and oil was 38.8" A.P.I. gravity. The Dublin area, where the Humble Oil and Refining Co. established a drilling depth record of 11,969 ft. drilling and completing its No. I Leonard Oil Co. well in the Ellenburger lime of Ordovician age. This well flowed 221 bbl. of oil per day, of 48.9º A.P.I. gravity oil. It is in sec. 12-26-37. The new pay horizon discovery of the Continental Oil Co. in the Skaggs area, where the company completed its Skaggs B-23 No. 2 in sec. 23-20-37 for 236 bbl. of oil in 21 hr. from the Wolfcamp section of lower Permian age, at a total depth of 7725 ft. This well was drilled to granite at 10,465 ft. and plugged back to the Wolf-camp for a new pay zone completion.

Jan 1, 1945

By W. O. Borcherdt

THE 650-ton underground mill of The Empire Zinc Company of Colorado (a subsidiary of The New Jersey Zinc Co.) serves the Eagle mine at Gilman in the Battle Mountain mining district of Colorado. The topography is rough, the mine and mill being under Battle Mountain and the adit entrance in the north wall of the canyon of the Eagle River, which is here a steel) gorge. The town of Gilman stands on a shoulder of the mountain at altitude 8975 ft., above sea level, along the Pike's Peak ocean to ocean highway and contains the company office and the usual facilities of a modern mining town. The railway contact is at Belden, altitude 8370 ft., at the bottom of the gorge directly below Gilman, where the westbound track of the Denver and Rio Grande Western Railroad is cut along the north bank and the eastbound track along the south bank of the river. A general description of the mine, mill and service facilities, with an account of the geology, character of the ore and methods of mining and milling having previously been published in a series of articles', this paper will discuss with as little repetition as practicable the reasons for building the mill underground rather than as a conventional structure, the methods of construction employed and the experiences gained in what is apparently the pioneer plant of this type and extent. There is a large historical background for underground plant construc-tion. From the dim past caves have been used for dwellings, stables, storage and shops. It was natural that where caves were available their many advantages led to their enlargement to suit convenience and where they were not available but the ground conditions, topography and, drainage were favorable, to the construction of artificial caves. In the vicinity of Epernay, France, extensive underground chambers protect the manufacture and storage of champagne-an intricate and ingenious application of chemical engineering-and in recent years these plants have been mechanized by the installation of conveyor systems. In the

Jan 1, 1937