Search Documents

By P. K. Guerrero, Nathaniel Arbiter

The correlation of power consumed by a tumbling mill with the dimensions, speed, and load has been attempted by three principal methods. One of these, the torque formula, has been reviewed critically elsewhere. This approach, while analytical, disregards the individual motion and speed of the tumbling bodies and assumes that the gross geometry of the entire load is sufficient to establish the power requirement. A more general approach, using dimensional analysis, has been applied in this laboratory by the present authors, and more recently by Rose. This disregards the internal conditions within the mill entirely and in effect is an empirical procedure for correlating data. Finally, the complete analysis of tumbling mill dynamics as first made by Davis attempts to develop the power requirement from individual ball and rod paths and velocities. Although Davis' result is applicable only at a single speed for a given size and load it could be useful, since his optimum speed is at the upper limits of conventional tumbling mill practice. Where power values predicted by the Davis equation were compared with actual mill requirements, they were found too low for small mills and much too high for the largest mills. This suggested that the agreement with actual intermediate range requirements might be fortuitous, and the development of the equation was examined critically.

Jan 5, 1960

The following rules, upon approval by the Board of Directors, shall serve as guides in the practical applications of the Bylaws for the operation of the Institute and have the full power and effect of Bylaws, however, these rules may be changed, modified, re¬pealed or amended when deemed necessary by the Board of Directors Any change or alteration of these Rules shall be published in the Journals of the Institute within three months after such alteration is adopted ARTICLE I-ORGANIZATIONS OF THE INSTITUTE Section 1-Societies Rule 1-Governing Body Each Society shall form its own governing body composed of an Executive Committee, or similarly designated executive body, duly elected officers, and a Nominating Committee for the nomination of Institute officers as provided by the Bylaws of AIME and of each Society approved by the Board In all correspondence and printed matter the Society Boards of Directors shall be specifically identified For ex¬ample, the Mining Board of Directors or the Board of Directors of the Society of Mining Engineers Using simply the "Board of Directors" could cause confusion

Jan 1, 1960

By W. M. Tuddenham, R. J. P. Lyon

In many areas surrounding the orebodies in mining districts rocks have been bleached and altered by the ore-forming solutions and have been oxidized during later weathering processes. A number of the rock-forming silic-ates have been broken down to clay, sericitic micas and chlorites have been developed, and pyrite may be found hundreds of feet outside the economic limits of the orebody. These halos of altered ground are prime targets used by geologists in many districts to delineate promising sites for drilling. Both in the field and in the laboratory it is often difficult to map these mineralogical changes in the halos in detail without numerous petrologic examinations. The secondary minerals are generally fine-grained, and since conversion of one mineral to another is often progressive, many alteration processes have not proceeded to completion (feldspars to clay to sericite mica). Qualitative detection of these minerals is difficult; quantitative determination is frequently impossible.

Jan 1, 1960

By J. L. Rodda

A large amount of time has been devoted to the microscopical study of the copper-zinc alloys, emphasis naturally being placed upon the commercially important alloys of the system. Suitable methods are available for microscopically recognizing the two phases richest in copper, but none appear to have been developed for the positive identification of the other phases. This is, however, accomplished, for the phases normally encountered, by an electrolytic method described in the following pages. Five phases of the copper-zinc diagram (Fig. I) are considered for the purpose of this paper: the solid solution of zinc in copper, alpha (a); the intermediate phases, beta (ß), gamma (?), and epsilon (e); and the solid solution of copper in zinc, eta (11). Beta prime is not considered a separate

Jan 1, 1937

By Richard M. Foose

WOULD you like to find a large new ore deposit next year? The answer is as obvious as the question is foolish. But perhaps the question does have some merit if we alter it slightly and ask: What are you doing about finding new ore? This one is more difficult to answer. Possibly you are doing nothing about finding new ore because you have proved reserves for many future years of production. Others may be investing some small percentage of time, effort, and money in mineral exploration, and reserves may be currently adequate, or inadequate, in terms of many future productive years. Still others may be engaged in large-scale mineral exploration programs involving large expenditures of time, personnel effort, and money. In whatever category you may be, a final question might well be asked. Is your current mineral exploration program, or lack of program, consistent with the long-range needs and objectives of your organization and of the mining industry as a whole, and is it designed to stimulate the growth of the industry in future years, or is it only a short-range program in response to some current situation?

Jan 3, 1958

By A. P. Miller, T. S. Washburn

Improved procedure in the manufacture of rail steel has come as the rail user demanded better wearing qualities combined with greater unit weight. With each weight increase per lineal yard has come greater difficulty in making a product that would successfully withstand all tests that modern rails must meet. With these facts in mind, and with a sincere desire to produce a rail whose service in track would be satisfactory in all respects, the steelmaker was quick to realize that all of the factors entering into his process would have to be more closely controlled. Control of rail-steel slags was recognized as one of the most important of many interdepending factors. The object of slag control is to hold the slag compositions within a range that gives the best results with respect to economy of production, uniformity of analysis, and quality of the finished rails. The most important component of the slag from the standpoint of these production and quality factors is the ferrous oxide content. This component is a good indicator of the basicity and oxidizing power of the slag, and these largely govern the effect of the slag on the steel. Consequently, the

Jan 1, 1935

By A. M. Gaudin, D. W. Fuerstenau

IN concentration of certain ores by soap flotation, prevention of quartz flotation is desired; the contrary is true in treatment of some oxide iron ores. Experimental study of the flotation of quartz goes back at least a quarter of a century.' Clean quartz does not float with fatty acids or soaps but does float when activated by one of many metallic salts. Control of pH is important. Broadly speaking the problem of quartz flotation has been approached from the empirical side, as was the related topic of flocculation or dispersion of quartz suspensions.' Empirical studies indicated the existence of critical relationships between the additions of collector and activator. These additions were not stoichiometric for the formation of soaps of the activator cation.

Jan 1, 1955

By R. D. Caudle, Yoginder P. Chugh, V. K. Agarwala

Longwall coal mining is a growing mining technique in the United States. However, very little premining exploration data are collected presently by coal companies to 1) select coal winning equipment, 2) select and design face supports and supports in gate and tail entries, or 3) optimize operational parameters such as length, width, and orientation of face. The authors are of the opinion that much of the data needed for mine planning and design for longwall mining can be obtained during exploration. In this paper, the authors identify the data requirements, discuss how these data can be obtained during exploration, propose an exploration program and estimate the cost to obtain the necessary data.

Jan 1, 1982

By A. N. Khayyat, R. G. Temple, R. Skelton

The fluid energy mill has been in use since the 1930's when an early patent was granted to N.H. Andrews in the USA. The microniser design has been basically unaltered since that date and current designs such as the Airfilco "Micronizer" have been progressively developed from results based on wide experience. The authors have been engaged in a research programme to establish optimum design and operational parameters for the Micronizer so as to provide a more quantitative basis for scale-up prediction of results. An introductory section will first trace the development of fluid energy milling including reference to other designs which have developed alongside the micronizer (especially the “Jet-o-miser"). With regard to design features the number of fluid injection nozzles and their size was investigated to establish the optimum range. Injection angle and, the consequent diameter of the internal "tangential circle" was carefully studied to determine the effect of this parameter on product size. The research was carried out using fine limestone as the test material with air as the grinding medium. Feed size fractions of 0-120µm, 0-250µm, 0-500µm, and 300-600µm were milled and product size analyses were carried out using the Coulter Counter technique.

Jan 1, 1980

By K. P. Wang, Virgil L. Barr

The U.S. Minerals Attaché Program, similar to the scientific and technical attache programs of other industrialized nations, is designed specifically to keep surveillance on significant worldwide developments in minerals, metals, and fuels. Knowledge of international minerals developments is essential for both domestic planning and conduct of foreign affairs. CONTROLLED BY DEPT. OF STATE Ten minerals specialists-eight minerals attaches and two petroleum attachés-man this far-flung, worldwide program for the U.S. Government as best they can. Minerals attach& also handle oil, in posts lacking petroleum attaché. The legislative authority for the Minerals Attaché Program is the Foreign Service Act of 1946 and succeeding amendments and Presidential Executive Orders. Therefore, this program is controlled by the Department of State. Interior (representing the Bureau of Mines) and State collaborate in policy formation and direction by means of a "memorandum of agreement" which covers establishment of posts, selection of officers, contents of reports, and supplemental training. State also has about half a dozen nonspecialist officers to complement the work of the minerals and petroleum attaché. It is not the intention here to evaluate the administrative arrangements of this program but rather to describe it and to provide examples of the important job it is doing.

Jan 11, 1965

By H. R. Thresh, A. F. Crawley, D. W. G. White

The densities of liquid tin, lead, and Sn-Pb alloys have been measured over a range of temperature above the liquidus. In all cases, data can be adequately represented by an equation of the type p = a + bT. For pure tin, the values of a and b are, respectively, 7.139 and 7.125 x 10-4, and for pure lead, 11.060 and 12.220 x 10-4. At constant temperature, molar volumes in the Sn-Pb system vary linearly with composition. DURING the course of a long-term program at the Department of Energy, Mines and Resources, Ottawa, Canada, the densities of liquid tin, lead, and Pb-Sn alloys were studied. The work reported herein draws on two sets of results independently achieved by Thresh, on the one hand, and by Crawley and White, on the other. EXPERIMENT The method and apparatus were originated by Thresh and have been described in detail in Mines Branch reports.172 In operation, the 14 cu cm graphite pycnometer is put in the furnace as shown in Fig. 1 after a machined charge has been placed inside the pycnometer and the lid screwed down. The dimensions of the charge are such that, upon melting, a small excess of liquid metal is discharged through the capillary hole to displace the weighted float above. When the pycnometer has been equilibrated at the experimental temperature, the

Jan 1, 1969

By L. D. Hall, S. J. Rothman

DIFFUSION coefficients of RaD (PD) and RaE (Bi) in a Bi-0.255 atomic pct Pb alloy have been measured by the methods outlined in a previous paper.' The following changes were made in the experimental procedures: the bath was made up of about 400 to 500 g Bi; and no correction was made for the volume change of bismuth on melting. The data are presented in Table I and Fig. 1. A least-squares analysis of the data yielded D = (0.120 t 0.09) exp ( -9680 + 1070/RT) D- (0.0465 0.001) exp (-8100 + 466/RT). Statistical analysis of the data indicated that the activation energies are significantly different at the 50 pct level, but not at the 75 pct level, while the D values are significantly different at the 97.5 pct level, but not at the 99 pct level. The differences are thus not as clear-cut as they were for lead. However, bismuth diffuses faster than lead in high bismuth alloys as well as in lead. The high activation energies, more than twice the value calculated from viscosities, are in good agreement with the results of Grace and Derge.' No data were obtained at higher temperatures because of gas bubble formation in the capillary. Acknowledgments This work was supported by the Office of Ordinance Research under contract DA-04-200-ORD-178. The authors thank 0. P. Vieria and M. Volpe for help in the experimental work.

Jan 1, 1957

By Henry D. Hibbard

Henry D. HibbaRd, Pittsburgh, Pa,: This is a most interesting and instructive paper, some of whose lessons should find immediate application. It points out how fuel-consumption is to be decreased in open-hearth practice, by changes in the plan of the furnace. To look first at the greatest item of loss, radiation, it is seen that thicker brick-work is advisable to lessen this. Especially is this true of the roof, made at present, almost universally, only 9 inches thick to prevent cutting. Now that high roofs, well above the course of the flame, are becoming general, and the average melter is better able to judge the temperature of his furnace, that reason has less force; and we may build roofs 18 inches thick, or perhaps better cover the usual 9 inches with an equivalent layer of sand, which has the advantage of following the arch as it rises and falls with the different degrees of heat. The side-walls of the hearth, usually 131/2 inches thick, may also he thickened up to 18 inches, and the door-linings to 7 inches; and the heat thereby saved will be valuable, while its absence from the working-platform will be much appreciated by the workmen.

Jan 1, 1892

Editors of engineering periodicals usually read the advertising pages. It may be hard' for some men, let alone engineers, to understand what value there is in reading "dry advertisements." Yet it is a fact that valuable suggestions have been obtained from these so-called "dry advertisements" which have been the means of securing greater efficiency in the performance of some undertaking and consequent saving of time and money. It seems to be an editorial practice to look to the advertisements for suggestions for the reading pages. It is a fact that some of the most appreciated descriptive articles were suggested by advertisements. Every undertaking is limited to that point where tools and machinery for its successful performance and completion may be purchased or manufactured. No work can he planned without having in mind such limitation, and the technical journals may be relied upon to furnish descriptions, both editorially and through the advertising pages, of methods and plant used in successfully performing various tasks. This being so, why should not the reader or subscriber to a magazine or periodical avail himself of such a fountain of knowledge? Such perusal proves of value to the up-to-date engineer or man occupying a -position. of responsibility where initiative is essential. Authorities agree that advertisements are on a par with technical articles for their educational value, and this Is as it should be. Also, most subscribers to a publication realize that a, successful advertising medium means a continuance of advertising patronage, which in turn enables the publisher to turn out a better and larger volume of reading matter.

Jan 6, 1915

By H. P. Willard, Conrad Martin

SINCE the deposits were found in 1927 in the Paradise Range of western Nevada, more than 1 mil- lion tons of magnesite and half a million tons of brucite have been mined and processed into a variety of granular refractory materials used as furnace linings by the steel industry. An additional million tons of magnesite were used during World War II to produce magnesium metal, and some magnesium oxide from the area is going into magnesia cements. Located near Gabbs, Nev., on the west flank of the Paradise Range, the principal bodies occupy an area a mile long by half a mile wide, and lesser occurrences have been found in a belt more than four miles long and in places almost two miles wide. Magnesite reserves containing less than 5 pct lime are estimated at more than 25 million tons. Reserves of better grade material are considerably less.

Jan 4, 1957

By H. N. Wolcott

Among the many cases of replacement of one mineral by another, that of quartz or silicates by pyrite, or even other sulphides, is not uncommon, but the reverse of this process does not appear to have been recorded, even if it has been observed. It seemed to the writer, therefore, that the case described below was worthy of record. Fig.1. GROUndALass of chalcopyrite (C) containing Rounded GRAINs of TYRITE (P) SHOWING DEFFERENT DEGREES OF REPLACEMENT BY QUARTZ (($), AND ALSO QUARTZ VEINLETS CUTTING THROUGH THE PYRITE. (PHOTOGRAPHED BY REFLECTED LIGHT.) The specimens described in this paper were obtained by R. B. Morton of Idaho Springs, Colo., from the Old Town mine, in Russell, Gulch, and ;re in the collection of Cornell University, where the writer studied them. In the rough, the specimens appeared to consist largely of chalcopy-rite. with some grains of tetrahediite. The polished surface of some of

Jan 1, 1918

By Axel Sahlin

The day is long past when linen and cotton rags were the exclusive raw material of the paper-trade. Wood-fiber, chemically or mechanically prepared, straw, hemp and Esparto grass have largely supplied the demand, which the old materials did not suffice to fill. But even these newer fibers have been of late supplanted, to some extent, by mineral pulp. Weighting and filling materials have also been resorted to, partly to give body to the fabric, partly to increase its weight and reduce the cost per pound. China clay, sulphate of lime and soapstone have generally been employed as loading materials. Even though these materials lack fiber, their addition must by no means be viewed, as it too generally is, entirely as an adulteration. No doubt, to a certain extent, they weaken the paper ; but for ordinary grades the addition of these non-fibrous substances is a positive advantage, as they close the pores between the fibers and lend to the paper a great degree of opaqueness and a superior finish. Fibrous talc, as a form of pulp, has the same effect, without appreciably weakening the paper. When, therefore, some fifteen years ago, fibrous talc in large quantities, and of marvellous purity and whiteness, was discovered in the neighborhood of the town of Gouverneur, it was not long before the

Jan 1, 1893

By David Burgess, Hershiel H. Hayden

Experiments at the Somerset mine, Colo., under an agreement between US. Steel Corp. and the US. Bureau of Mines are described. A test was made of the tube bundle method of mine air sampling which was developed for European longwall mines; some 300,000 running feet of tubing provided continuous monitoring at 38 locations. Carbon monoxide concentrations were obtained with standard deviations of less than 1 ppm and oxygen concentrations with standard deviations of less than 0.2%. A base level of CO index (ppm CO evolved per percent 0, removed) was determined to be zero to 20 through most of the passageways of the mine. However, in one working section where the coal was initially hot (about 180°F within a pillar) the CO index was demonstrably higher, 120 trending upward to about 60 when smoke appeared and the section was sealed. The data are discussed in terms of laboratory experiments on CO evolution from coals.

Jan 1, 1977

By Max Barber

PRESENT equipment and practices in open-pit mines of the Lake Superior iron ranges have been described recently in some detail by A. H. Hubbell.1 It is anticipated that any further improvements will be the result of gradual evolution of present methods and equipment, just as those now used have been gradually evolved from earlier methods. An exception to the process of gradual evolution during the last decade has been the adoption of electric power for operating shovels and trains in open-pit mines, but it is not expected that any such revolutionary changes will be made in the future. The use of Diesel, engine equipment will gain considerable headway, no doubt, and will find favor in certain lines of operation as improvements and adaptations are evolved to meet particular requirements. The question of installing belt conveyors for handling material from deep mines of restricted area, where haulage grades become a serious consideration, or even for transferring earth, rock, or ore material for distances of several miles, is now being studied and some very interesting data are being obtained.

Jan 1, 1932

By J. C. Osler

The design of a tailings dam is a geotechnical engineering project of considerable scope. For the design, it is necessary to establish the engineering properties of the soil or rock strata which will support the dam and the tailings or other fill which will be used to construct the dam. The various field and laboratory investigations which are necessary to obtain the required design parameters are discussed in the paper and the use of these parameters to compute stability, settlement, and seepage are considered. The designer of a tailings dam can never assume an absolute knowledge of the properties of the foundation strata. Further, initial design assumptions are often approximate, particularly with regard to the distribution of pore pressures through and beneath the dam. Thus, the installation of performance monitoring instruments is recommended, since data obtained from such instrumentation can be used to check the stability of the structure both during construction and after its completion.

Jan 1, 1972