Search Documents

By R. W. Gurry

Thermodynamic calculations indicate that boron is a better deoxidizer than silicon but probably is not quite as effective as aluminum. Boron should, therefore, be readily oxidized out of the open-hearth bath, which implies that it is not recovered in significant concentration from any scrap charged; also that, if added in the ladle, it tends to oxidize out during teeming unless protected by the presence of a better deoxidizing agent. These conclusions do not apply to liquid cast iron, in which the oxygen content is much lower than in liquid steel. The possibility of conserving certain strategic alloying elements widely used in steelmaking, notably manganese, chromium and molybdenum, by the use of boron, which in small concentration appears to be extraordinarily effective in promoting hardenability, raises a question as to what extent any boron present in the scrap charged into the open hearth is oxidized out during melting and subsequent refining. This question is significant because the optimum concentration of boron in the finished steel, which is fairly critical, would be very difficult to attain if the boron in the charge were largely retained in the metal. Moreover, unless boron is substantially eliminated in the open-hearth process its use on a large scale would eventually make it impossible to produce boron-free steel except by restricting the charge to virgin material. There is at present, unfortunately, virtually no satisfactory direct evidence to provide an answer to this question; but there are indications from practice that boron is oxidized out in the open hearth in the production of medium or low-carbon steel, although it may be retained if the carbon content remains fairly high; that is, if the oxygen is kept fairly low. In the absence of direct data, it is necessary to rely upon the indications of indirect evidence, the best approach now available being a thermodynamic calculation of the deoxidizing power of boron in liquid steel by the general method used so successfully by Chipman1 in his study of the reactions in the open-hearth process. The thermal data for boron, upon which such a calculation must be based, are reasonably satisfactory; the only quantities not directly determined are the entropy of melting of boron, the activity coefficient of boron in liquid steel, and the activity coefficient of B2O3in an open-hearth slag; but these values may be estimated with ample accuracy. The results of this calculation, which is presented later, are given in Table I, together with corresponding data for other deoxidizing elements. This table shows the calculated residual content of oxygen in equilibrium with different residual concentrations of the deoxidizer in the metal;

Jan 1, 1944

By C. G. McLachlan

THIS paper outlines a series of tests carried out during the first six months of 1927, in the laboratory and mill of the Moctezuma Copper Co. The object of the tests was to determine whether the soluble salts present in the mill circuit water were having a detrimental effect on the recovery made by flotation. To accomplish this object a series of water analyses were made, followed by flotation experiments in which definite quantities of the salts found were added as addition agents. Before proceeding to describe the results obtained in the course of the investigation, reference will be made to five articles that have appeared during the last two years in which the action of such salts is discussed. Two of these are by A. T. Tye1,2 and describe flotation practice at Cananea and the way in which water high in ferrous and ferric salts is conditioned for differential flotation. Two, one by A. C. Munro and H. A. Pearse3 and the other by H. A. Pearse,4 outline Britannia milling methods, and the advantages that have been derived from ore washing; while in the fifth, A. W. Hahn5 summarizes the results of laboratory experiments in which ferrous, ferric and aluminum sulfates have been added in varying amounts. The mill of the Moctezuma Copper Co. has a daily capacity of 3000 tons, and is situated about 75 miles south of Douglas, Arizona, on the Rio de Nacozari, in the Mexican state of Sonora. The ore treated is mined from the company's mine at Pilares, about 5 miles southeast of the Concentrator. This ore contains about 2.5 per. cent. copper -- present almost entirely as chalcopyrite-and 10 per cent. iron, of which

Jan 1, 1928

By Ian William Wark, Alwyn Birchmore Cox

Sodium sulfide is used extensively to increase the recovery of oxidized copper and lead minerals by flotation, particularly when using xanthates as collectors. It is generally assumed that the sodium sulfide converts a film of the oxidized mineral to the sulfide, and that the xanthate, while not a very effective collector for the oxidized minerals, is a good collector for the sulfide. On the other hand, Taggart and his collaborators1 claim that unless sulfide minerals are oxidized they cannot adsorb xanthates and do not float. Gaudin2 states that amyl xanthate, used in conjunction with sodium sulfide, gives better results than ethyl xanthate. Rabone3 and Mayer-Schranz4 agree that excess of sulfide functions as a depressant. Owing to the greater solubilities of the oxidized minerals than of the sulfides, the consumption of sodium sulfide is greater than that of most other flotation reagents, up to 10 lb. per ton of ore being used in some plants. Luyken and Bierbrauer5 recommend a water washing to remove soluble heavy metal salts; by this means sulfide consumption may be reduced. It was desirable to determine the limits of the sulfide concentrations between which contact is possible at surfaces of anglesite and cerussite in xanthate solutions. Similar determinations were desirable for the sulfide minerals with which the oxidized minerals are usually associated, since conditions should be chosen, if possible, so that the two types of mineral will float together. Because of the formation, especially in acid solutions, of hydrogen sulfide and of the hydrosulfide ion (HS-), the permissible limits of sulfide addition are obviously dependent upon the pH value. Sphalerite responds to ethyl xanthate only in the presence of an activator; for example, copper sulfate. It was necessary, therefore, to determine whether sodium sulfide interferes with the activation of sphalerite by copper sulfate. The combined effect of sulfide and copper sulfate was determined also for galena, chalcopyrite and pyrite.

Jan 1, 1939

By Douglas Bunting

THE first presentation of this paper was before the Pennsylvania Anthracite Section of the Institute in May, 1914, after which a committee was selected to verify and add to the data contained in the original paper. The author is indebted to G. W. Engel, H. W. Montz, R. V. Norris, and H. H. Otto, of this committee, for additional information. I also wish to acknowledge the courtesies extended me by a number of the mining companies for information relative to accidents, systems of proving, and mining practice. The paper should bring forth additional criticism and recommendations, which will be of value in establishing future practice relative to this subject. Throughout the northern anthracite field of Pennsylvania glacial and alluvial deposits of sand, gravel, and clay exist in varying quantities. The extent and character of these deposits are described by N. H. Darton in Bulletin 45 of the U. S. Bureau of Mines, entitled, Sand Available for Filling Mine Workings in the Northern Anthracite Basin. It is estimated that the northern field contains 10,000,000,000 tons of these deposits, or a sufficient quantity to cover the 176 square miles of coal area to a depth of about 25 ft. These deposits of sand, etc., overlying the coal measures attain a maximum depth of more than 300 ft., and are usually saturated to such an extent as to render them semi-fluid. It is .this condition of fluidity that limits the mining of coal seams cropping in or in close proximity to these deposits, and it is in the interest of safer and more efficient mining methods under these conditions that the study of this -subject is here presented. The dangers incident to mining under deep deposits of sand have long been realized by operators in the northern anthracite field, and much has been done to prove the contour of the rock and vein croppings underlying these water-bearing deposits of sand and gravel.

Jan 1, 1915

By Albert E. Ketler

Introduction – The introduction of computerized monitoring and control (M/c) equipment into the U.S. coal mining industry may prove to be of truly revolutionary proportions in the 801s.Many of you are aware that the British have developed and have been using such sophisticated M/C equipment for performing production and safety related tasks in their coal mines for nearly a decade. The benefits of M/C systems in the mining industry are usually separated into those which improve productivity, and hence make money for the company, and those which improve safety, and hence cost money. The economic benefits of M/C are startling for the production related functions such as for monitoring and controlling conveyor belts, de-watering pumps, electrical power distribution, and the like. It doesn't take much analysis to show that hundreds and even thousands of tons of coal don't get mined every time a belt shuts down or when power is out due to circuit breakers tripping for any number of reasons. A flood, caused by a malfunctioning pump which goes undetected for lack of feedback monitoring of pumping parameters, can destroy literally millions of dollars worth of mining equipment. The M/C system would be justified or not based on whether or not the productivity benefits balanced the cost within a timespan commensurate with the return on capital philosophy of the company. The safety related benefits are easily underestimated or ignored completely and the purpose of this paper is to under-score some of these benefits, as well as to review the application of M/C to the coal mining industry. The companies involved are Transmitton Ltd of England and Minetics Corp of Pittsburgh, Pennsylvania. Transmitton is probably the most experienced manufacturer of M/C equipment in the world having some 200 installations to its credit. Minetics is the marketing and manufacturing arm for Transmitton in the U.S.A. and is responsible for all aspects of distribution and service. Plans are underway for manufacturing of the Transmitton hardware for U.S. sales to be transplanted into U.S. subcontractors by 1981. Thus our coal mining industry will benefit from British technology, but without the delays and additional costs usually involved in international shipments.

Jan 1, 1981

By R. Schumann

THE expression "unit process " comes up with increasing frequency in discussions among metallurgists and mineral engineers, especially among those concerned with training the next generation. The unit process approach characterizes a significant advance along the road from metallurgy as an empirical art to metallurgy as a branch of engineering. The purposes of this paper are to define and list the unit processes in specific terms, to indicate the scientific and engineering principles basic to all the unit processes, and finally to show how these ideas have been applied to a reorganization of instruction in chemical metallurgy. UNIT OPERATIONS AND UNIT PROCESSES Metals are extracted from ores and other raw materials by stepwise procedures. In general, each metallic element is extracted by a different procedure. For many of the metals there is a choice of several flowsheets. However, the procedures all have steps in common. In fact, the many different flowsheets are all made up of a relatively small number of steps which are combined in different groups and sequences. For example, crushing, screening, roasting, sintering, melting, and gaseous reduction are steps which each appear in the flowsheets for extracting the majority of the metals. The individual steps or flowsheet units can be designated as unit operations or unit processes. These terms are well established in the field of chemical engineering, as the American Institute of Chemical Engineers' definition of chemical engineering shows: " Chemical engineering is that branch of engineering concerned with the development and application of manufacturing processes in which chemical or certain physical changes of materials are involved. These processes may usually be resolved into a coordinated series of unit physical operations and unit chemical processes. The work of the chemical engineer is concerned primarily with the design, construction, and operation of equipment and plants in which these unit operations and processes are applied. Chemistry, physics, and mathematics are the underlying sciences of chemical engineering, and economics its guide in practice."1a In this definition, the distinction between unit operations and unit processes is that the unit operations are physical while the unit processes are chemical. Table I gives a list of the principal unit operations and unit processes of chemical engineering, taken from Shreve. lb Table 2 lists the principal unit operations and unit processes used for metal extraction. The division between unit operations and unit processes is similar to the chemical engineers' distinction and also corresponds approximately to the division of labor between mineral dressing and chemical metallurgy which has been customary in the past. Furthermore, it will be noted that in the proposed classification the unit processes primarily involve chemical reactions and/or changes in state of aggregation; the unit operations, primarily do not involve either bulk

Jan 1, 1948

By H. R. Fife

AN extended study of dustproofing Freeport-seam coal has empha-sized several fundamental features in the successful treating of bituminous coals. The extent of the exposed surface area and its absorption proper-ties for the dust-retaining film were found to be the most critical factors affecting the efficiency of fly-dust prevention. From recently published screen data and specific surface-area measure-ments on United Kingdom coals, an approximation of the surface exposed by mine-run coal and by 1-in. slack was made. The total surface area exposed by an average ton of this mine-run coal was estimated at 3768 sq. yd., while a ton of 1-in. slack represents a total surface area of 8779 sq. yd. with no additions for porosity. It is important in coal treating to consider that in mine-run coal the fraction above 1/4 in. in size represents 79.5 per cent of the total weight, but only 4 per cent of the total surface, while the fraction below 150 mesh contains 47 per cent of the total surface and only 1.2 per cent of the total weight. Also, one should appreciate that, in a 1-in. slack, the domestic stoker fraction (1 in. to 8 mesh) contains 76.3 per cent of the weight and 8.2 per cent of the surface, while the fraction below 150 mesh represents 3.3 per cent by weight and 54.8 per cent by sur-face area. Wax extraction data on 1-in. to 0 slack from mine-run treated Free-port-seam coal showed that the coating was distributed uniformly as a function of exposed surface; hence, nonuniformly on a weight basis. This distribution of the coating on mine-run coal therefore limits the extent of treating that is desirable on bituminous coal at this point in the preparation. The treatment of Freeport mine-run coal before it reached the tipple gave a 70 to 80 per cent reduction of fly-dust in the tipple, a satisfactory treated commercial slack coal, and an indicated change in the trend of tipple degradation. The premium-treated domestic sizes required a supplemental treatment for complete dustproofness.

Jan 1, 1937

By James Gayley

The lining of the hearth and bosh of a blast-furnace has naturally come to be considered its weakest part, being subject not only to abrasion, but also to intense chemical action. In order to provide against rapidity of wear, it was formerly customary to build the lining from the mantle to the top first, and to put in afterwards the hearth and bosh, drawing the latter into a recess that had been reserved for it in the upper lining. At some works this practice still prevails ; but through the progressive development of cooling-devices, it has become possible to protect the bosh so well as to make it the most durable part of the furnace. The main question now is, by which one out of several methods the best economy results can be obtained. The plain bosh-jacket, made of wrought-iron or steel, and frequently called the air-cooled jacket, was a great improvement over the crinoline-construction formerly in vogue; but it was difficult in many cases to persuade furnace-managers, that in order to secure its best effects, they must discard the thick bosh-walls and put in comparatively thin ones. Mr John M. Hartman, who did more perhaps than any one to extend the use of these jackets, invariably contended for a 13-inch wall, the thin wall being an essential part of this construction. Later, a coil of pipe was placed just inside the jacket, through which water, circulating freely, contributed further to the proper maintenance of the walls. Undoubtedly much better results have been obtained in practice where the iron jacket has been supplemented by a coil in this way. It is safe to say that this combination of water-coil and jacket is much better than external sprays on the jacket; but it does not prevent the brick-work from cutting entirely away, which enlarges the bosh to that extent and interferes with the economy and output of the furnace. In case of leakage or stopping-up of the pipes, they cannot be replaced. A leading blast-furnace manager who is now using this construction

Jan 1, 1893

By C. F. Willis

Many of the failures in vocational education are due to the fact that the educational methods were not designed to the capabilities, habits, and environments of those to be trained; rather they were based on the policy that education is education and lessons are lessons, whether for youngsters of fifteen or for men of forty. Vocational education among miners involves, first, a study of the men themselves, their habits, and the use of their leisure time; second, a study of the differences between the methods of teaching required for men and for children. Certain fundamental requirements of training methods for miners are reasonably universal and may be applied with success to any ordinary mining community. The rate of labor turnover is another consideration; it would be useless to design a four-year course for men who remain in one place only a few months. Length of Course The first consideration should be the length of the course. Few mining communities have a sufficiently stable population to make it possible successfully to carry on a course for over a year. While some men might complete a four-year course, the number is comparatively small compared with the number to whom a shorter course would be of service, and it is better to raise the standards of education even a little for a large number than to raise them to a high level for a few. It is perfectly possible to attain both objectives by arranging the courses in small units; all the units, when grouped together, should comprise a fairly complete course, yet any one unit should be complete in itself and of benefit to the workman. It should not take many of these units to make a miner or a timberman out of a mucker; but to do this the course should be short, because muckers seldom stay in one place long. By grouping a number of these units together it Would be possible for a miner to become a shift boss or a shift boss a foreman, and so on. As far as possible the units of the course should not be dependent on those preceding or following. The workman understands the completed job but he is not accustomed to carrying on several jobs at the same time and

Jan 1, 1920

By John B. Mertie

More than 200 minerals are known that contain the rare-earths and thorium. Monazite and bastnaesite, however, are the principal commercial sources of the rare-earths, and monazite is the principal source of thorium. Monazite was in demand in earlier years mainly for its content of thorium, which was used in the manufacture of Welsbach gas mantles; but beginning in the latter part of the nineteenth century, the rare-earths became progressively more important than thorium. Recently, however, the tenor of thorium in monazite has again become a matter of commercial interest. Rare-Earths and Thorium The rare-earths proper are defined by spectroscopists as the oxides of 14 elements with atomic numbers ranging from 58 to 71; but more commonly lanthanum, with an atomic number of 57, is also included, in which case these 15 elements are often designated as the lanthanides. Chemists also include scandium and yttrium as elements of the rare-earths. A second group of elements, beginning with actinium and including thorium, protactinium, uranium, and all the transuranium elements so far produced, with atomic numbers ranging from 89 upward, are chemically and structurally related to the lanthanides, and are known as the higher rare-earths or actinides. Berzelius discovered that the lanthanides could be separated roughly into three groups, based upon the solubility of their double salts, R2(SO4)3-K2SO4-2H2O, in excess of K2SO4. This separation, with the substitution of sodium for potassium, is still used commercially. The double salts of the cerium earths were found to be almost insoluble; the terbium earths, partly soluble; and the yttrium earths, completely soluble. Based upon the degree of solubility, scandium belongs with the cerium earths; and yttrium belongs with, and gives its name to, the yttrium earths. These three groups with their atomic numbers are shown below. [ ] The prevailing state of oxidation for the rare-earths is R2O3, but cerium may readily be oxidized to the tetravalent state, in which condition it may be separated chemically from the other cerium earths. Praseodymium and terbium may also exist with the valence IV, and samarium, europium, and ytterbium may have the valence II. Most of the elements of the rare-earths, however, are very difficult to separate, and their initial isolation required the work of many chemists over a period of 150 years.20 Fractional crystallization, fractional precipitation, and ion exchange are the principal methods so far used, and fractional precipitation is now employed commercially on a large scale. Ion exchange columns are

Jan 1, 1960

Discussion of the paper of, RICHARD H. RICE, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 89, May, 1914, pp. 721 to 743. S. G. VALENTINE, Oxford, N. J.-In a paper read at the New York meeting of the Institute last February I presented some notes taken from our experience with the turbo blower operating on a blast furnace. In connection with Mr. Rice's very interesting paper there are a few items that might be of further practical interest. The question of the reliability of this type of blower will naturally be presented. In this connection we would say that our turbo blower has been in practically continuous use during the present blast, which was begun June 7, 1912, with only three interruptions for repairs of any consequence. Soon after blowing in there was developed a tendency of the blower to surge or pulsate. This occurred on operating at a point considerably below the normal capacity of the machine, and was checked with comparatively little trouble by throttling the intake slightly and taking up a small lost motion on the governor connections, a legacy of the previous blast that had not been attended to. All this required only a few hours' time. In. March, 1914, the furnace being banked on account of a blizzard that cut off our freight deliveries for five days, the opportunity was used to replace the carbon packing on the steam-turbine shaft and to repack the steam inlet valves. In June, 1914, the blower was off 8 hr. to replace an oil ring and scrape a bearing. With these exceptions we have made continuous use of the machine and find we can depend upon it with entire safety as a piece of machinery.

Jan 4, 1915

By W. F. Dietrich

This paper deals with the methods of mining the high-grade clays of California. The fact that the majority of the clay pits in the state are operated on a scale that is small by comparison with most metal mines causes a diversity of methods and gives rise to problems of selection of the method best suited to given conditions. Two or three operators in California produce approximately 500 tons per day of a single kind of clay from a single pit. About five varieties of clay are mined on a scale of 200 to 400 tons per day; not over 15 varieties are mined on a scale of 50 to 200 tons per day; and more than 50 varieties are mined at the rate of less than 50 tons per day. It is the aim of this paper to delimit, as far as the data at hand permit, the conditions and scale of operations that favor the selection of each dominant method of mining that is actually being applied at California properties. Details of the occurrence and utilization of the clays of California have been given in a recent bulletin1 and will not be considered here. Geographical and Geological Features of California Clay Deposits The greater part of the high-grade clays consumed by clay-working plants in California is mined from one of three producing areas in the state: (1) Lincoln, Placer County, on the eastern edge of the Sacramento valley, 30 miles northeast of Sacramento; (2) Ione, Amador County, in the foothills of the Sierra Nevada, 38 miles northeast of Stockton, and 12 miles west of Jackson, one of the important towns of the famous Mother Lode gold-mining district; and (3) Alberhill, Riverside County, 90 miles southeast of Los Angeles. Other districts of minor importance are near Cardiff and Carlsbad, San Diego County, and El Toro and San Juan Capistrano, Orange County. In addition, there are a number of isolated properties in various parts of the state.

Jan 1, 1928

By Donald Barton

Geophysical methods of prospecting taken as a whole do not seem to offer much promise to a young man planning to enter them in the future. They have come to stay, to be sure, and they will continue in at least moderate use for a long time. Domestic use of those methods presumably is at a maximum at the present time. Geophysical pros-pecting is expensive; the effects of the law of diminishing returns in efficiency in finding prospects can already, be recognized. Small oil companies, independent oil operators, and royalty buyers have been doing much geophysical work. But in face of the increasing costs of discovery of prospects and in face of the probably decreasing favorability of the prospects discovered, I expect to see a sharp drop in their use of geo-physics within the next 10 years. The major oil companies and the larger small oil companies will continue to use geophysics indefinitely, but it seems doubtful whether the very extensive domestic campaigns of a few companies will be maintained for many years, certainly not for 10 years. The use of the geophysical methods in foreign countries has not yet reached its peak, and probaby will continue to increase for several years. That peak level of activity will probably be held for 10 years, although the site of maximum activity will shift from country to country; by the end of 25 years from now, I should expect the foreign use of the methods to have leveled off to one-fourth to one-half the peak level. Foreign service in geophysics does not seem to offer an attractive career, except for men of exceptional disposition. Young men just out of college, who are willing and who can afford to spend three or four years having a fling at adventure before settling down, will find it attractive, but when their tour of foreign service is over, they probably will have harder work finding a job than when they were seniors, and their foreign experience will count for little, except for further foreign service. A few men, mainly the higher men, will have headquarters at civilized or semi-civilized cities and towns or at permanent oil-company towns, and can

Jan 1, 1938

By Martin A. Mayers

Five-sixths of all the coal that is mined in the United States is burned, without previous treatment other than screening, for the production of heat and power, so that its value is fixed by its suitability for this purpose. Nevertheless, the characteristics of individual coals that determine their fitness for use in particular pieces of combustion equipment are not yet well known. This condition is due not only to the small extent of our knowledge concerning coal itself, but also to our comparative ignorance of the nature of the combustion process. The following paper is an analysis of the combustion process as it occurs in industrial furnaces, based largely on the results of laboratory research on combustion rates. From this analysis it is possible to determine the characteristics of the fuel that limit the capacity of a given piece of combustion equipment. Limitations imposed by other factors than the attainable speed of combustion will not be considered, since they are subject to a different type of analysis involving the balancing of maintenance costs against fixed charges. In order to observe the relations among the various factors that affect the speed of combustion, representative particles of fuel will be followed through two types of furnaces. A pulverized-coal furnace will be considered first, because the independence of the individual particles facilitates the analysis of the effect of furnace conditions. The second example will be a grate-fired furnace in which ignition of the fuel takes place on the underfeed principle. This includes both underfeed and chain grate stokers, (8)† but does not include hand-fired furnaces and some overfeed stokers. The furnace will be considered to be large enough, the temperature high enough, and enough air provided, to burn the fuel completely, without, for the moment, specifying these quantities more completely. Furnaces Burning Pulverized Coal In a pulverized-coal furnace, the fuel particle is carried, in a stream of air, into the furnace, where it is subjected to radiation from the flame and from the hot walls of the furnace. The increase of particle tempera-

Jan 1, 1936

By R. W. Gurry

Thermodynamic calculations indicate that boron is a better deoxidizer than silicon but probably is not quite as effective as aluminum. Boron should, therefore, be readily oxidized out of the open-hearth bath, which implies that it is not recovered in significant concentration from any scrap charged; also that, if added in the ladle, it tends to oxidize out during teeming unless protected by the presence of a better deoxidizing agent. These conclusions do not apply to liquid cast iron, in which the oxygen content is much lower than in liquid steel. The possibility of conserving certain strategic alloying elements widely used in steelmaking, notably manganese, chromium and molybdenum, by the use of boron, which in small concentration appears to be extraordinarily effective in promoting hardenability, raises a question as to what extent any boron present in the scrap charged into the open hearth is oxidized out during melting and subsequent refining. This question is significant because the optimum concentration of boron in the finished steel, which is fairly critical, would be very difficult to attain if the boron in the charge were largely retained in the metal. Moreover, unless boron is substantially eliminated in the open-hearth process its use on a large scale would eventually make it impossible to produce boron-free steel except by restricting the charge to virgin material. There is at present, unfortunately, virtually no satisfactory direct evidence to provide an answer to this question; but there are indications from practice that boron is oxidized out in the open hearth in the production of medium or low-carbon steel, although it may be retained if the carbon content remains fairly high; that is, if the oxygen is kept fairly low. In the absence of direct data, it is necessary to rely upon the indications of indirect evidence, the best approach now available being a thermodynamic calculation of the deoxidizing power of boron in liquid steel by the general method used so successfully by Chipman1 in his study of the reactions in the open-hearth process. The thermal data for boron, upon which such a calculation must be based, are reasonably satisfactory; the only quantities not directly determined are the entropy of melting of boron, the activity coefficient of boron in liquid steel, and the activity coefficient of B2O3in an open-hearth slag; but these values may be estimated with ample accuracy. The results of this calculation, which is presented later, are given in Table I, together with corresponding data for other deoxidizing elements. This table shows the calculated residual content of oxygen in equilibrium with different residual concentrations of the deoxidizer in the metal;

Jan 1, 1944

By Robert Warner

WHEN a new mine is opened, and often when an operating mine must adapt itself to physical or economic changes, a mining system must be selected in complete detail. In the past the plan chosen was usually the product of the local staff alone, however limited the training and experi-ence of that staff might be, which often resulted in the introduction of methods that were familiar to the staff, but not so well suited to the con-ditions as others unknown to the local men. A new management, noting the difficulties with the existing layout, might make modifications or complete changes, so that many mines in their history have seen a whole series of mining systems, each somewhat laboriously grafted on to its predecessor. This should not be interpreted as a condemnation of the older staffs for sticking to the tried systems, such as open square-sets in the early days at the Homestake, because they knew it would work after a fashion, nor does the statement apply to the technically trained, and usually broadly experienced staffs of most present-day properties. The older miners did not have the variety of tools and methods, nor the present freedom of transfer of information as to what the other man is doing, and so did the best they could under the circumstances. Finally, the higher grade of the ores made the choice less vital. The ever-increasing need to mine low-grade orebodies, with a fixed or even lower price for the metal produced, has caused an increasing need for low-cost mining. In most new mines this has simplified the problem of selection by eliminating from consideration all of the high-cost systems, but it has also complicated the choice by the necessity for refinement in detail and a close adjustment of the plan selected to all the conditions at the property. In these low-cost problems any textbook division of mining systems as applied to "beds, veins or masses" avails little as a guide. It should be realized at the outset that to' be successful under modern competitive conditions a system of mining must be worked out with elaborate detail, with careful time scheduling and control of the various elemental operations, and that after it is introduced it must be run with a large amount of technical direction.

Jan 1, 1933

By E. Beril

This may be a most unnecessary paper—from what does crude oil come and how was it formed. Many people, inside and outside of the petroleum industry, believe that we have actually enough oil, and that we can easily produce very important products from this extremely valuable raw material. The writer believes, however, that the answer to this question concerning the parent material and the formation of oil is of broader interest, because it may be that from the answer to these problems it would be possible to get answers to other important industrial questions. Therefore, a study in this line seems to be justified, and the writer will submit some of the results which he has collected during more than ten years with many very capable collaborators, to whom his thanks may be expressed on this occasion. Older Theories There is no doubt that plants were the parent material of coals, but opinion is divided as to the parent material of crude oil and asphalts. One group of specialists believed that they were formed from dead fish. The hydrocarbons of crude oil were formed by the splitting off of CO² from fatty acids formed by the saponification of the fat (glycerides) of fish. Enormous quantities of crude oil are present in many places on the earth, very often in several nonconnected horizons at the same location. This could hardly be explained by the so-called "catastrophe theory," which states that fish died through the entrance of salt water into fresh water, and vice versa. Furthermore, this theory cannot explain the presence of aromatic hydrocarbons, which can be found in nearly all oils, especially in the oil of the Netherlands Indies, which has more than 50 per cent of aromatics. Geological and chemical observations both lead to the belief that the temperature of formation of asphalt, crude oils and coals, perhaps with a few exceptions, did not exceed 200° C. Chlorophyll and haemin derivatives, which decompose above 200° C., have been found in all these materials by Treibs and others. Thermodynamic considerations show that the temperature necessary for the conversion

Jan 1, 1938

By S. F. Shaw

The theory that maintaining a high back-pressure on the oil sand lowers the viscosity of the oil has been generally accepted. The theory has also been advanced that lower viscosity permits the oil to be moved through the sand to the well at an expenditure of less gas per barrel of oil than would otherwise be required. It seems reasonable to assume that production of oil at the minimum gas-oil ratio will result in a greater ultimate recovery of oil. During the past five years the writer has acquired data on thousands of tests made on wells to determine the best rate at which to produce them. In the majority of cases reduction in back-pressure did not definitely increase the gas-oil ratio. The information obtained from these tests has raised doubt in the mind of the writer as to the correctness of the theory that lowered viscosity results in lower gas-oil ratios and in higher ultimate recovery of oil. The reasons that explain the results obtained in these tests cannot yet be definitely stated, but the hypothesis is being tentatively assumed that there are other factors which outweigh the influence of viscosity. Energy in Gas Moves Oil to Well The general opinion is that in most cases it is the energy in the gas that moves the oil to the well. In wells flowing naturally it is also the energy in the gas that lifts the oil to the surface. In a flowing well, there are two very distinct operations: 1. Moving the oil through the sand to the well. 2. Lifting the oil to the surface. The more important function of the gas is that of moving the oil to the well. Means for lifting the oil can always be found once it has been delivered to the well. Principles Involved in Lifting Oil A well that flows naturally is the same as a gas-lift well except that all of the gas is supplied by the oil reservoir. This natural flow is subject

Jan 1, 1931

By Wallace F. Lovejoy

The conservation of mineral resources as a public policy question has received a great deal of attention in the area of petroleum and practically no attention in other mineral areas, except, of course, soil and water. Some insights into mineral conservation problems and how these problems can be approached in the social decision-making process are significant. THE MEANINGS OF CONSERVATION Conservation means many things to many people .2, 11 Too often it is a label attached to a proposed program or policy to add respectability and to gain public acceptance. It is a term applied to specific resources in some contexts and to resources generally in other contexts. The oft-quoted comment of President William Howard Taft that conservation is something everybody is for, no matter what it means, succinctly illustrates the confusion over both the meaning of the concept and the policies required to implement a conservation program. This confusion goes quite deep and is more than a matter of semantics or emphasis. For example, the efficient exploitation of a mineral deposit which might be applauded as good conservation in terms of that mineral, might well result in destruction of or harm to the environment which might be viewed as bad conservation. Economics provides some tools to help solve this sort of problem, but there may be fundamental differences in value systems among groups in this society, so that ultimately society must collectively make a subjective political choice as to what is good or bad conservation policy.a An Economic Definition of Conservation The economic concepts of conservation have more relevance and are more easily applied to minerals than to many other natural resources. This does not mean that economics goes all the way in understanding mineral conservation, but at least it provides a framework for analysis which later can be altered to include noneconomic variables. Perhaps the greatest confusion in discussing mineral conservation arises in attempting to relate purely physical concepts with economic concepts. An economist is interested in maximizing or conserving values; he is not interested in maximum physical recovery or utilization. He wants to know the costs and benefits of using, or not using, resources. The economic theory of mineral-resource conservation can be labeled variously as the theory of exhaustion, the theory of resource exploitation, the theory of resource utilization, or simply as a special case of the broad theory of capital.4,28 Consideration of these labels illuminates the concerns of the econo-

Jan 1, 1976

Joseph Esrey Johnson, Jr., had already achieved rare distinction as an able metallurgist, clear thinker, brilliant author, and wise consulting engineer to bankers and operators; he had achieved the essentials of a great career when dcath cut short his activities on Apr. 4, 1919, in the forty-ninth year of his age. He belonged to a family of iron blast-furnace men and mine managers. His father, Major J. E. Johnson, after serving with distinction in the Army of the North, identified himself with the iron mines and blast furnace at Longdale, Va., with which he was connected during almost his entire business life. It is significant, that, during those troublous times of reconstruction in the South, he enjoyed always the affection and respect of his neighbors and associates alike. From him his son obtained not only a thorough training in blast-furnace practice and iron mining, but great personal courage and force of character. His mother, who survives both her husband and sons, possesses rare intellectuality, humor and a tenderness and human sympathy which those who were privileged to know well J. E. Johnson, Jr., recognized beneath his exterior of aggressiveness and will power. In a recently published analysis of the qualities which characterize the world's great men, three traits stand out preeminently; viz., independence, courage, and intellectuality. Each of these characteristics J. E. Johnson, Jr., possessed in extraordinary degree. His early education was obtained under a private tutor at Longdale, and this circumstance probably enhanced a natural tendency to independence of character and individuality which, however, under the control of his unusual power of straight thinking and clear analysis never allowed him to go far astray. It has been said of him that if once he set his mind to a problem, however knotty, he scored a bull's-eye before the subject was dropped. His manner of attacking a subject involved first mastering the details of the available knowledge; then, putting this acquired information to one side, with an untrammeled mind blazing out a path of his own, so clear, so well-defined, and expressed in such simple terms that he illuminated the whole subject without distorting the original data or discussion. His two books, "Blast-furnace Construction in America" and "The Principles, Operation, and Products of the Blast Furnace, "on the iron blast furnace together form the most comprehensive, the most enlightening, and the most useful treatise on the subject ever produced in any language. But his ability did not end with the mastery and elucidation of principles enunciated by his predecessors; his own

Jan 1, 1920