Search Documents

By J. D. McBeth, G. M. Potter, Ramon Pizarro

Heap leaching is used by the Carlin Gold Mining Co., Carlin, Nev., to supplement conventional processing of gold ore by agitation-leaching and countercurrent decantation. Selected open-pit ore containing about 0.072 oz Au per ton is crushed to 3/4 inch, dumped by truck on an asphalt pad, and leached by sprinkling with dilute cyanide solution for 7 days. The heap is then drained and removed by front-end loader to tailings disposal. About 70 percent of the gold is dissolved. Leach solution from the heap joins the pregnant solution from countercurrent decantation for gold recovery by zinc precipitation. Four leach pads, each with a capacity of 1,400 tons of ore, are in use. About 10,000 tons of ore are heap leached monthly from about April through October. Heap leaching is recessed during freezing weather. Labor, equipment, and reagent requirements for heap leaching are presented.

Jan 1, 1974

By Irwin Roman

IN a previous paper,1 a method was suggested for determining the depth to a bed in the simple case of a uniform overlying layer of constant thickness. The main purpose of the present paper is to show how a slight modification of that method has been used to interpret specific data obtained in the upper peninsula of Michigan by the staff of the Depart- FIG. 1.-THE TECTONIC CONFIGURATION. ment of Mathematics and Physics of the Michigan College of Mining and Technology. The method of Tagg2 has also been used on the same data, thus furnishing a comparison of the e two methods, as well as a method of using the two methods jointly. The method of measuring the apparent resistivity is that suggested by Wenner,3 and illustrated in Fig. 1. A current I enters the earth at the positive pole C and leaves it at the negative pole D. The potential V of the high electrode A, with respect to the low electrode B is measured by suitable means. The separation of the collinear points in the order shown, DBAC, is 1, the same. for each interval.

Jan 1, 1934

By R. T. Murrill

BLOCK-SIGNAL and dispatching systems have been in use on surface railways for years, but only recently have they been applied to underground mining conditions. Formerly, all ore was moved underground by hand tramming; the surface openings were numerous and fairly close to the ore being mined. As the tramming distances increased, animals were brought into service. Then came the locomotive, and since its introduction, haulage lines have gradually been reduced to fewer levels and to fewer surface openings until more than 20,000 tons are being handled daily on one level in some of the larger mines. Under the, se conditions many trains must use the same-tracks, and signal systems have become necessary. In some cases it has been found more advantageous to use train dispatchers than to install signal devices. The dispatcher may be simply a flagman at a busy point or he may have mechanical signals to operate at more distant points. At the inspiration mine, Inspira-tion, Ariz., the station is equipped with a switch-con-trol board, whereby the dispatcher throws electrically all track switches in a certain block, which gives him complete control over all trains passing through that block. In a few cases, dispatcher stations are established in connection with a signal system.

Jan 2, 1922

By C. W. Crispell

The four nomograms presented in this article were designed to simplify and make more rapid the calculations connected with the compression and transmission of air. The formulae involved are rather complicated, but the graphic solutions are simple; their use requires an ability to follow explicit directions and to interpolate values on a logarithmic sca1e. † For the sake of convenience, the nomograms will be divided into two classes, and the purpose and accuracy of each will be discussed. Power foR CompREssion It is frequently desirable to determine the horsepower necessary to compress a given amount of free air from atmospheric pressure to a certain final pressure. The nomograms in Fig. 1 and 2 present a rapid method of calculating the horsepower required to compress 1 cu. ft. of free air per minute by single or two-stage compression. The general formula for the horsepower required to compress air adiabatically is: S X 144 PVn [(P')n-1/sn -1 (1) where: P = absolute atmospheric pressure at compressor, in pounds per square inch. P' = final absolute pressure of compressed air, -in pounds per square inch. V = volume of free air compressed per minute, in cubic feet. S = number of stages. n = exponent of the compression curve.

Jan 1, 1918

By O. Bilharz

The rules laid down by Peter von Rittinger in his classic Lehrbuch der Aufbereitungskunde (Berlin, 1867, p. 513) concerning the designing of dressing-works still possess authority for such works and their operation. Nevertheless, some modifications and additions suggested by practice may be of value at the present time. Rittinger says: "I. Choose the apparatus and machines which can be, under the existing con-' ditions, easily constructed and kept in running order!' This rule contemplates the construction of apparatus (mostly of wood) on the spot, with the command of good sbops and especially of good workmen in wood. But in many cases, particularly for the sake of a prompt supply, the construction of apparatus is now left to special manufactories, which pay more attention in the choice of materials to durability and strength than to easy manipulation and erection. Nevertheless, here,as in many other instances, simplicity of construction and solidity of execution are to be recommended. Especially important is the convenient and cheap replaceability of

Jan 1, 1894

By Gilbert Thiessen

THE purposes of this paper are (1) to show that the mineral matter content of coal is satisfactorily represented by the Parr formula; that is, Mineral matter = 1.08 Ash + 0.55 Total sulfur (2) to compare ash-to-mineral-matter ratios with factors by which ash values must be multiplied in order that dry, factor-times-ash-free values shall equal Parr unit coal values; (3) to examine such ash-correction factors and to compare them with similar factors corresponding to certain simplifications or modifications of the Parr formulas and (4) to show that ash-correction factors used for simplification in calculating approximate unit coal calorific values cannot be. correctly used for the conversion of other determined values in an analysis to the unit coal basis, but that each type of calculation requires separate treatment in simplification.

Jan 1, 1934

By Francis Laur

BAUXITE, at first considered as a mineralogical curiosity without importance, now attracts daily increased attention from mineralogists, geologists, and manufacturers. The metallurgy of aluminum, which has entered with the advent of electrolysis upon a new phase within the last few years, requires every day larger quantities of pure alumina, and this can only be obtained from bauxite, which is, of known substances, the richest in free alumina. Bauxite has been mined since 1872 in France, whereabout 200,000 tons have been produced, and where, as a natural consequence, its deposits, qualities, and applications have become known. Within a few years past, discoveries of important deposits of bauxite have been made in the United States and Canada, and this almost entirely new subject has thus acquired an additional interest for the mining engineers and metallurgists of the American continent. A brief summary of the available data concerning it appears likely, therefore, to be appropriate and valuable.* I.—HISTORICAL. It was in 1821 that the famous chemist Berthier discovered at Baux (Bouches du Rhône) a hydrate of alumina (varying from 66 to 79 per cent. in its contents of the oxide) mixed with silica and

Jan 1, 1895

By F. P. Agterberg

It can be useful to model the mean grade values for a metal in mineral deposits containing that metal as representing the extreme value tail of a lognormal frequency distribution for the concentration values of the metal in common rocks of all types. Results for copper and zinc in the Abitibi area of the Canadian Shield are compared to results previously obtained for the Canadian Appalachian region. The lognormal model is also applied to a set of 162 large gold deposits in the Abitibi area. In the second part of the paper, 1311 large and small gold deposits in the Abitibi area are modeled as discrete events. By means of a newly developed spatial clustering model it is possible to predict the variances of random variables for frequencies of deposits in cells of different sizes.

Jan 1, 1981

By William E. Bruce

This paper is intended to provide an improved understanding of natural draft (natural ventilating pressure) and the effect of natural draft on underground mine ventilation circuits. Attention is focused on measurement of natural draft pressures during ventilation surveys in mechanically ventilated mines and on different methods for modeling natural draft using the measured data. A number of examples are presented which utilize data collected during absolute air pressure surveys made by personnel of the Ventilation Division of the Mine Safety and Health Administration's Safety and Health Technology Center, Denver, Colorado. Examples are used to illustrate how the data from absolute air pressure surveys may be interpreted to determine whether natural draft pressure is present and what its magnitude is. In addition, two different methods are described for mathematically estimating the magnitude of the natural draft pressure. Comparisons are made of results obtained using the different methods. Different procedures are described for modeling natural draft using the MSHA-modified Penn State computer program. Use of the routines is described and illustrated relative to drafts that aid or oppose the mechanical ventilation system. Tabulations of results facilitate comparison of outcomes obtained using the different modeling procedures.

Jan 1, 1982

By J. H. Brophy, A. I. Prill

The authors have previously investigated the solid-state activated sintering of tungsten powder with various Ni-Cu additions.' Log shrinkage vs log time plots showed changes in slope from 4 to x at intermediate times during the sintering process. This was attributed to a change in the rate-controlling mass-transport process from solution of tungsten into the tungsten-alloy interface to diffusion of tungsten in this interface. It was postulated that the melting of the activating layer should not affect this transport process. However, the superposition of rearrangement due to the presence of a liquid phase complicates the data analysis. It is the purpose of this note to apply the analysis of Prill, Hayden, and rohy' to account for "rearrangement shrinkage'? in liquid-phase sintering of the W-Ni-Cu system. This results in "solution-precipitation stage" shrinkage plots which were comparable to those obtained in solid-phase activated sintering of the same system. If one assumes total shrinkage to be the sum of rearrangement and solution precipitation, the effects can be isolated easily.2 This results in the general equation:

Jan 1, 1967

By Henry E. Colton

Very little information has been published concerning the Tennessee coal-field. The State never appropriated over $600 per annum for a geological survey, and that was discontinued about 1870. Yet even with that small sum Dr. J. M. Safford made a

Jan 1, 1886

By Harry V. Warren

There are two topics which may be considered as opening gambits in any conversation in any part of the world, weather and health. Nothing much can be done about the former, and it would appear that no great changes can be anticipated in the immediate future. With respect to health, a great deal has been achieved in the past 150 years, curiously enough not all of it by medical men. It would appear that the time is now appropriate for geologists to come to the assistance of medical men. During the past few decades, medical science has mastered many of the diseases commonly associated with childhood. As a man tends to live longer, those diseases usually associated with middle and old age become more prominent. Thus we must realize when we say that today more people are dying of cancer and coronary disease, absolutely and relatively to other diseases, this should not suggest that these diseases did not exist a hundred years ago; it does suggest that more people are living to an age where death from these diseases is apt to become more common.

Jan 7, 1962

By Orr Hamilton

VALUATION of a mine is an approximation of its true cash value which requires the application of fundamental principles of economics. Mines are valued from necessity, for the following reasons: (a) Transfers of titles. (b) Dissolutions of partnerships or corporations. (c) Mergers of mining companies. (d) Appraisals for the purpose of State and Federal taxation. (e) Establishment of the fact of worth as a basis of loans. (f) Determination of values as frequently required in litigation. (g) Listing of stock for sale by a reputable stock exchange. For the majority of purposes a valuation is required as at the present time, but for some purposes valuations as of bygone times may more nearly reflect the intrinsic worth of a mine because its subsequent history can never be, entirely ignored, but valuations made as at the present time are better indicators of cash values. Many mines with great intrinsic worth have been sold for small cash prices. The object of legitimate mine valuations is to deter-mine salable value, or that price in cash at which a transfer of the property from a willing seller to a willing buyer might be consummated, assuming that both vendor and vendee have knowledge of all pertinent data and that the owner, is not forced to sell at a sacri-fice-the definitions of fair market value precluding a forced sale.

Jan 11, 1923

By Ronald A. Murdock

INTRODUCTION Exxon's Highland Uranium Operations in eastern Wyoming consists of an open pit, an underground mine and a mill complex. The geology of the deposit is reviewed in this paper, and an overview of the mining operations at both the surface and underground mines is presented. Topics discussed include geology, stripping of overburden and mining of ore in the open pit, and underground development and stoping methods. GEOLOGY The Highland uranium deposit was discovered in 1968 by Exxon Minerals Company, U.S.A., in Converse County, Wyoming, 35 miles north of Douglas. The mine is located at an elevation of about 5,200 ft in a high-plains, sagebrush-covered prairie typical of eastern Wyoming. The deposit is near the southern edge of the Powder River Basin in the Paleocene Fort Union Formation. The Fort Union Formation consists of 1,900 to 3,200 ft of sandstone, siltstone, mudstone, claystone and coal beds. Siltstone, mudstone and claystone are collectively referred to as "shale" at Highland. There are many alternating layers of shale and sandstone in the Fort Union Formation; but in the Highland area, there are only three principal sandstones, known as the Highland Sand Group, which host the uranium. The combined sand thickness is about 150 ft.

Jan 1, 1983

By D. J. Dunn, J. L. Huiatt, T. E. Norman

Corrosion studies in laboratory ball mills and grinding environment simulations produce corrision rates and total metal removal rates much lower than those recorded in operating production ball mills. The corrosion component of ball metal loss in many mills probably represents less than 10% of the total loss, judging from AMAX experience and recent US Bureau of Mines (USBM) tests. Such small absolute losses are consistent with ball metal loss measured in production ball mill marked ball wear tests to determine effects of corrosion and abrasion resisting properties of alloys in operating mills. These indicate that metal hardness and microstructure determine relative metal loss rates of a given situation. The combination of ore characteristics and grinding process dynamics determine metal loss severity. Alloying for corrosion resistance and modification of the milling corrosion environment yield relatively small metal loss reductions. Alloying and heat treatment to produce high hardness and microstructures of high carbon martensite and, for cast irons M7C3 carbides, produces the lowest metal losses in typical wet grinding applications.

Jan 1, 1986

By Sharon Brady, Catherine O’Donoghue, John V. Beall, Paul C. Merritt

Between 1950 and 1965, more than 80% of all phosphate rock produced in the world each year was used as fertilizer, either directly applied to the soil or processed into mixed chemical fertilizers. Of the potassium salts produced, 95% followed suit. A variety of uses in industrial chemicals and consumer products absorbed the remaining percentage of each. Future trends in these two commodities will be dominated by what happens to the fertilizer market. Farming is much the same as mining the soil. Plants remove the minerals little by little. Phosphate and potash comprise two of the three primary nutrients removed in this way, the third being nitrogen. Phosphate stimulates early root formation and growth, whereas potash is a salt necessary to root strength.

Jan 10, 1966

By H. E. Wilborg

This chapter deals with those sands employed by the foundries for the manufacture of cores and molds used in the casting of such common metals as steel, gray iron, ductile iron, aluminum-based alloys, and copper-based alloys. Most metal is cast in "green sand" molds in which the sand mixture, consisting primarily of silica, clay, and water, forms a plastic material. This plastic material is rammed around a pattern in a split box called a flask, then the box is separated, the pattern is withdrawn, and the metal poured. These green sand molds are broken apart when the metal has solidified. The sand is then remixed and a new mold made for the next casting. To a lesser extent silica sand is mixed with resins or oils and, after forming, the mixture is hardened either by heat or chemical reaction. In any case, the foundry mold or core is used just once before being broken up and remixed for manufacturing another core or mold. By far the greatest consumption in the foundry is of those types of sand high in silica, low in clay (under 0.5%) and occurring in numerous locations thoughout the United States.

Jan 1, 1975

By H. R. Hanley

ONE of the most important contributions to the art of electrolytic zinc production-has been the aluminum cathode. This has been used in all major production: since its commercial development in 1916. The literature is replete with important contributions, some of which may have been replaced by better ones, but thus far there appears no other metal to take the place of aluminum as cathode material. Credit for this innovation goes to Sherard Cowper Coles, of England. When experi-menting on the extraction of-zinc from Broken Hill ore at Hayle, Cornwall, in 1893, he introduced the aluminum cathode, and in 1895 obtained British Patent-No. 20073. The reason for this dominant position of aluminum as cathode mate-rial in zinc sulphate electrolytes is its unique surface, to which electro-deposited metals usually do not tightly adhere. The metal must be of high purity for best results. It is possible to develop a starting-sheet method by which thin electro-deposited sheets of cathode zinc are made and stripped from a smooth aluminum plate. Such thin sheets of cathode zinc may be used as arc tine copper sheets in standard electrolytic copper-refinery practice. However, complications arise because of extreme warping of the zinc starting sheet after a .few hours of deposition, and thus special arrangements must be made to compensate for this abnormality.

Jan 1, 1938

By L. L. Wyman

PREVIOUS studies1 by the writer dealing with the embrittlement of copper have been concerned with the behavior of various pure and deoxidized coppers when exposed to an oxidation-reduction cycle, and the consequent evaluation of these materials on the basis of their resist-ance to this action. No attention was devoted to the variations in pene-tration of embrittlement with time, when these copper materials are exposed to a strong reducing gas, such as hydrogen, nor to the variations in oxygen penetration, with time and temperature, into the "pure" coppers. The cause of the embrittlement is the reduction of the oxygen in the copper by the hot reducing gas, so that a consideration of time, tempera-ture, the occurrence of hydrogen and oxygen must be given. For the purpose of differentiating some of "the involved factors, the present work may be divided into two separate series of experiments. The first of these deals with the oxidation of purified coppers under various conditions and then the subjection of these to a standard hydrogen treatment. The second series concerns the reduction, under different conditions, of tough-pitch coppers of several oxygen contents. The resulting data will give the rates of oxidation, and of reduction, for the materials involved. The first series of experiments will reveal how rapidly copper may become oxidized, while the second series will indicate how rapidly embrittlement will penetrate into an oxygen-containing copper when it is exposed to hydrogen at different temperatures.

Jan 1, 1933

By E. B. Spice

Although much may be learned about the economics of cold weather operations by studying successful mining ventures in southern and central Canada, it is the purpose of this article to extend the study by considering only permafrost areas. Geographically this means most of the country north of the 60th parallel. In this area, at the present time, only five Canadian companies are carrying on routine and successful mining operations on a year-round basis. However, there have been some score of unsuccessful ventures, and a number of properties in the development stage show promise of being producers. Problems of cold weather are worthy of study. It may be pointed out that successful mines in this area face problems of isolation and costly transportation as well as cold weather. To reach valid conclusions, consider the development of a mythical mineral deposit located on the 65th parallel in the heart of the barren lands; problems of isolation and transportation will be ignored.

Jul 1, 1956