Search Documents

By B. Etkin, A. A. Haasz

The Infrasizer Mk III, developed at the University of Toronto, is capable of sizing particles of a few pm to hundreds of pm according to particle terminal velocity, which is a function of particle density, size and shape. The factors limiting the performance of the Infrasizer Mk III have been presented and analyzed. It has been established theoretically and experimentally that the device has excellent potential as a laboratory instrument. The principle is applicable to a continuous production classifier, a prototype of which is now under development.

Jan 1, 1980

By Alexander Bowie

Of the following problems, some have been suggested by recent articles in technical journals, which have led me to believe that the mathematical discussion here submitted may be of use to mining engineers. Problem I. To Find the Grade or Angle of Inclination upon which the Power Required to Move a Loaded Car Down-hill Will Haul an Empty One Up-hill. Let a be the desired angle of inclination; C, the coefficient of' friction; W and w, the weight in pounds of the loaded and of the empty car, respectively.

Jan 1, 1902

By G. H. Walrod, J. M. Mutmansky, Y. J. Wang

The selection of a shaft size for ventilation purposes is a classic problem of concern to mining engineers. This presentation is concerned with the sizing of conventionally-sunk circular shafts with concrete or shotcrete linings. Costs of sinking shafts of three different depths, from 150 m to 300 m (500 ft to 1000 ft), and six different diameters, from 4.27 m to 7.32 m (14 ft to 24 ft), were obtained through questionnaires to shaft contractors. The primary objective of the economic model presented is the balancing of detailed annual capital and operating costs to achieve the minimum overall cost of the shaft installation over its life. The economic model is similar to previous analyses but treats several of the individual cost categories in an updated fashion. Included in the paper is a detailed analysis of the effects of varying power costs on optimal shaft size. Also included are a statistical analysis of current shaft costs and comments on the choice between shotcrete and concrete linings.

Jan 1, 1979

By Wilson Blake

Rock deformation and failure taking place around underground openings is usually both accompanied and preceded by the phenomena of rock noise or microseismic activity. These small-scale releases of seismic and acoustic energy can be detected with special geophysical monitoring equipment. Use of this equipment allows one to look inside a rock mass to determine how an opening is behaving under the applied loading system. Microseismic equipment and monitoring techniques are briefly reviewed, and use of the microseismic method as an engineering tool in monitoring rock structure stability is illustrated by case histories. Examples cited range from evaluating roof stability using single-channel portable equipment, to rock burst monitoring using sophisticated computer controlled, multichannel monitoring systems.

Jan 1, 1983

By Sumner M. Anderson

Any discussion of outside support to Latin American mineral industries must concede at once the pre-eminent role of U. S. industry and business. American capital has developed the great copper resources of Chile and Peru, the lead-zinc of Peru and Mexico, the bauxite of Surinam and Jamaica, the petroleum and iron ore of Venezuela. American consumers have provided the market for their products. U. S. companies operating south of the border have trained Latin American geologists, engineers, chemists, and skilled labor-including metal, mineral, and fuel technicians-to new and greater competence. The industrial demands of World War II drastically altered world economics and concepts of U. S. foreign mineral requirements. In this country discovery of vital mineral resources fell far behind the alarming depletion rates, and there was new appreciation of the actual and potential importance of the world's less extensively explored areas. During the war and afterward, the task of supplying the nation's mineral requirements became greater than private industry could carry alone, and the Government assumed a position of continuing support.

Jan 11, 1958

By Frank C. Appleyard

Southwest of the town of Saltville in western Virginia is Plasterco, a small village that has been a source of gypsum production since 1815. Boasting the deepest underground gypsum mine in the world, Plasterco has been the site of mining operations by United States Gypsum Co. for more than half a century. And although its own ore supply is dwindling, Plasterco's position as a source of gypsum and gypsum products has been ensured by the recent opening of the nearby Locust Cove mine, one of U.S. Gypsum's newest projects. In the early days, production of gypsum at Plasterco was very small, the primary use of the mineral limited to that of "land plaster"-ground gypsum spread on the land to sweeten the soil. Initial mining was confined to surface outcrops containing gypsum, but the construction of a local plaster-producing calcining plant in the late 1800's coupled with al- most total depletion of the surface rock spurred the start-up of underground operations.

Jan 3, 1965

By Robert M. Lewis

Silica sand deposits are usually contaminated with various heavy minerals which must be removed to make the silica useful for flat-glass production. Research was undertaken to develop a better procedure for producing flat-glass-grade silica. Batch tests revealed that anionic detergent-type reagents had considerable promise. Pilot plant tests were run to compare the effectiveness of anionic detergent-type reagents with petroleum sulfonate in the removal of heavy minerals from a potential glass sand. Another slightly modified commercial procedure also was evaluated for comparison. In the pilot plant trials, utilization of the anionic detergent potation reagents did not produce quite as good results as petroleum sulfonate. It is likely that flat glass-grade sand could be produced with the anionic detergent reagents if more extensive pilot plant tests were conducted.

Jan 1, 1977

By T. L. Kesler

With only six small spodumene prospect pits, no detailed mapping, and no subsurface information in 1938, the Carolina lithium-pegmatite area now contains four mines among more than 25 properties on which exploratory work has been done. Even the open pit mine of Foote Mineral Co. described herein, from which ten million tons of ore and waste have been removed since 1952, was virgin ground when mapped in 1938-40 1. It has been a privilege to participate in the transition. In 1940, the spodumene pegmatites were known in a 25-mile belt (originally noted for tin prospecting) between Lincolnton, N. C. and Grover at the South Carolina line. Subsequently, Broadhurst 2 reported relatively small bodies northeast of Lincolnton near the Catawba County line. To the south, diamond drilling done in 1953 on the old Ross tin-mine property near Gaffney yielded pegmatite cores containing a few crystals of spodumene. This fact, not previously reported, suggests that some of the pyroxene in the Ross shaft as described by Sloan 3 may be spodumene.

Jan 9, 1961

By J. F. Abel, F. T. Lee

Subsidence is controlled by a complex com¬bination of mining and geologic factors. For example, a compilation of worldwide data shows that, as the percentage of shale in the overlying rock mass decreases and the amount of sandstone increases, the angle of draw (and the area affected by subsidence) decreases. Limestone in the over¬burden appears to cause a more than twofold decrease in the angle of draw compared to a like amount of sandstone. Increased amounts of sandstone were accompanied by a greater surface subsidence relative to the mining height. The total thickness of overburden did not appear to influence the subsidence magnitude above super-critical panels. The greater the thickness extracted, the smaller percentage of that thickness shows up at the surface as subsidence. The greater the percent of the seam extracted, the greater the subsidence reaching the surface. The maximum subsidence above room-and-pillar panels de¬pends on the pillar height and minimum width as well as the other factors listed.

Jan 1, 1984

By H. L. James

THIS paper presents the results and analysis of field trials of various magnetic instruments over anomalies ranging from 20 to 5000 gammas of vertical intensity. The following instruments were used: Askania vertical magnetometer, Wolfson vertical magnetometer (model M-I), Hotchkiss Superdips (used both parallel to and normal to the magnetic meridian, with several settings of the "sigma" angle), Lake Superior dip needle, and the dipping circle for measurements of inclination. The change in inclination over the measured anomalies ranged up to 4°; this caused pronounced changes in sensitivity of the Hotchkiss Superdip oriented parallel to the magnetic meridian. The variable sensitivity not only gives apparent displacement of crests of anomalies, particularly at high sensitivities, but also makes the data difficult or impossible to use in preparation of iso-anomaly maps. This weakness in field performance of the Superdip is shown to be eliminated by orienting the instrument normal to the magnetic meridian and measuring vertical intensity only, which in the latitude of upper Michigan is equal to 97 pct of the total intensity. The dip needle is seen to be relatively ineffectual for location of anomalies of less than 400 gammas.

Jan 1, 1947

By D. W. Brunton

The object of the investigations and experiments here recorded was to obtain such information and data as would make it possible to determine the fineness to which crushing must be carried, in sampling gold- and silver-ores, in order to obtain results within an allowable limit of error.

Jan 1, 1896

By Robert Maddin

crystal prior to, polishing in order to eliminate coring. This treatment may be accomplished by wrapping the single crystal tightly in very thin, dead soft, brass foil and annealing in the presence of air for 20 hr at 800°C. Since the wrapping encircles the sptcimen three to four times, only a very slight amount of oxidation occurs on the specimen surface. On unwrapping one of these cylindrical single crystals. in. in diam by ro in. long (72.75 pct cu, 27.23 pct Zn, 0.01 pct P11, 0.01 pct re), mall light-gray depnrrits in the form of circular arcs werenoted on the part nf the foil which had been in contact with the single crystal, Fig r. (By superim- approximatetl). These deposits, which, from their color, suggest the appearance of sublimated zinc, were found to coincide roughly with a set of octahedral planes nearly perpendicular to the rod axis. The pattern shorn in the figure held no relation to the profle of the sample since the markin~s on the crystal More annealing werc attributed to traces of cube planes. It seems very likely that the deposits were formed by sutllimation of zinc diffusing from octahrdral planes since diffusian would Eogically take place along planes of maximum atomic spacing. However, it is difficult to understand why a continuous sublimation of zinc should occur from a single crystat in contact with a wrapping roil OF the same composition, and why diffusion would take place along specific octahedral planes and in a regular pattern.

Jan 1, 1949

By G. S. Brooks

(New York Meeting, February, 1913.) THE tendency of the oxides of such metals as aluminum, zinc, chromium, and calcium to form compounds at high temperatures with iron oxide is well established by past investigation. Data of this reaction, as developed in laboratory research, have been contributed by Burleigh, Hofman, and Wells, in America, and by many others abroad. A partial bibliography of the subject is appended. From these authorities we learn that the ferric oxide here has the function of an acid, giving in the case of ZnO a zinc ferrite, with a normal composition of ZnOFe2O3. This formation of zinc ferrite particularly affects the success of such processes as leaching or magnetic separation, and thus becomes practically important to the metallurgist. But the meager existing data do not entirely agree; and quantitative results from muffle-practice are conspicuously absent. Furthermore, it being of some general importance to the zinc smelter in both roasting and reduction, the following few notes of operations on a commercial scale are contributed

Jan 5, 1913

By K. J. Edmiston, R. C. Kellner

Shortly after production was begun at the Duval Sierrita concentrator in February 1970, it became evident that difficulties would be experienced in reaching the designed operating level of 72,000 stpd. Since the major restrictions to production resided in the reduction crushing system, a comprehensive program was initiated to evaluate and optimize all crusher parameters affecting production. Positive relationships were established between production rate and crusher power draught, mantle support pressure, crusher setting, and crusher throw. Other parameters evaluated were the effects of feed distribution, crusher speed, mantle and concave configuration, choke feeding, and ore type. In order to obtain maximum production, it was also imperative that the mechanical integrity of the crushers be improved. Therefore, redesign of nearly the entire crusher assemblage, including such items as the top shell, bushings, and the mantle hydraulic support system, was required. In addition, automatic control stategies were evaluated and detailed operating guidelines were established. As a result of this extensive crusher examination, the limitation on plant throughput has been shifted to the grinding section, and a monthly average production level of 86,000 stpd is currently achieved. Programs under current evaluation are aimed at further increasing capacity to exceed 90,000 stpd.

Jan 1, 1976

By Francis T. Freeland

The deeper workings of the Leadville mines show refractory ores, consisting principally of sulphides of iron, lead, and zinc, carrying silver, in place of the easily reduced carbonate ores lying nearer the surface. The largest and most extensively developed deposit is that of South Iron Hill.* It lies on the north side of California Gulch,

Jan 1, 1886

By J. C. Konopka, S. A. G. Poppen, E. K. Roesner

Many shafts have experienced stability problems during shaft sinking because the designer failed to fully appreciate the conditions he would encounter. Some shafts have failed during construction because the ground supports provided to compensate for the expected conditions were inadequate despite the most careful investigations and analyses. To design a ground support which is ultimately safe to achieve stability during shaft sinking would be too costly and impractical and, therefore, many shafts would simply not be constructed. The design of a ground support for shaft sinking based on an intimate understanding of the expected ground behaviour and stress development during excavation combines the art of mining with the science of geotechnical engineering. Where no historical design data is available, the designer of the ground support must: 1. classify the rocks and soils and assess their behavioural characteristics; 2. calculate the primary and secondary stresses; 3. design and/or select a ground support system which will ensure stability of the excavation during shaft sinking.

Jan 1, 1983

By J. H. Smith, H. W. Paxton

X HE recent investigation of Butler, McCabe, and paxton' on the vapor pressure of manganese gas in equilibrium with Mn-Fe alloys has been extended to include the iron-rich solutions and alloys in the two phase equilibrium region. The study of the phase equilibrium by Kurnakov and Troneva2 and the extensive reviews of the Mn-Fe system by Hansen,3 and Hellawe114 are not in agreement with regard to the location and extent of the equilibrium between the solid phases of fcc y and complex P in the temperature range above the eutectoid temperature of approximately 975Kwhere 0 decomposes to y and bcc a. An evaluation of the existing equilibrium data is confronted with the conflicting results presented by various investigators who used techniques requiring a quenching treatment to retain the high-temperature equilibrium or encountered temperature hysteresis during thermal analyses. The difficulty of suppressing the transformation of the manganese-rich concentrations of the y-solid solution during quenching has been well etablished.' To avoid this uncertainty the phase equilibrium was investigated at temperature by measuring the partial pressure of manganese gas in equilibrium

Jan 1, 1962

By William Daly

THE application of artificial refrigeration, or air-conditioning, to the ventilation of deep, hot mines has long been a subject of interest to the operators of such properties. Artificial cooling of the air in theaters, railroad coaches, and various industrial plants has been so successful within recent years that it has been natural to assume that the adoption of similar methods would afford a ready solution to the difficult problem of mine ventilation. It should however, be obvious, that although there may be nothing technically impossible in the application of this process to mine ventilation there is a great economic distinction between the maintenance of a high standard of comfort for a large number of people in a relatively small space such as a theater and the cooling of air to improve working conditions for miners scattered throughout the extensive workings of a large mine. Many methods of air-conditioning have been considered by the management of the Anaconda Copper Mining Co. at various times, but until the development of the process to be described in this paper none has seemed economically practicable.

Jan 1, 1934

By Alan K. Burton

The number of trucks required to perform a certain task is a function of the productive capability of one independent truck and the total tonnage required. Hourly productive capability of one truck is the product of trips, or cycles, per operating hour and effective payload. One cycle is made up of load, dump, and travel time, the sum of which comprises theoretical cycle time. This time is then derated by a productivity factor, giving an average effective cycle time which is used to calculate the number of cycles per hour. Rated payload is the truck's designed tonnage, while effective payload is the average amount that is actually carried. Manufacturers, particularly of the larger trucks, produce various body sizes designed to carry materials of different densities. However, it is not always possible to carry the rated payload because the material might be lighter than expected, a body of the required size cannot be produced, or because of spillage on particularly steep grades.

Jan 12, 1975

By W. M. McKewan

A large amount of work has been reported in the literature on reduction of cubes, spheres, or regularly shaped particles of iron ore. Previously, it has been difficult to evaluate these data because no equation has been developed that would yield one or more constants for comparison of overall reduction rates. Iron ore in the process of gaseous reduction is a complex system. The reduction takes place through the series Fe2O3-Fe304-Fe0-Fe. Edstrom and Bit-sianesl have reported that the gas-solid type of reaction was found only at the FeO-Fe interface and that the internal reduction proceeded by elementary diffusion of iron. Therefore, during reduction oxygen is essentially removed from the system only at the FeO-Fe interface. Kinetically, it is reasonable to consider iron ore in the process of reduction as a

Jan 1, 1959