Search Documents

By Galen H. Clevenger

Equipment for treating lead ores was added in 1905 to a copper plant which the United States Smelting Refining and Mining Co. had built in 1902 at Midvale, Utah, about 12 miles to the south of Salt Lake City. By 1906 the lead section of the plant had been rounded out and consisted of a 90-ton gravity concentrator, fifteen hand-rabbled reverbera-tory roasting furnaces, six blast furnaces, a briquetting plant for handling flue dust and fine ores, a regulus furnace for concentrating the low-grade matte made in the blast furnaces, and a baghouse. The copper section was later abandoned and the plant has been operated for many years exclusively as a lead smelter. Some 45 years had elapsed at the time this plant was built since the first attempts to smelt lead ores in the West, and lead smelting had become a large and profitable industry but fundamentally little that was really new had been developed, which could be embodied in a plant built in this period. Principles and tools to work with had remained much the same as those borrowed earlier from European practice. Capacities had been increased and there were mechanical improvements but hand charging was still in vogue and there was little attempt to recover suspended particles carried out with the furnace gases, beyond settling in flues, which usually was only partly effective for recovery of the coarser particles. Satisfactory roasting and preparation of the fine components of the charge were still partially solved problems. The Midvale plant of 1906 may be regarded as more or less typical of the smelting plant of this period for treating complex western lead ores as distinguished from the recovery of lead from the simple lead ores to the eastward. The operation of a concentrating mill directly in conjunction with a lead smelter was, however, not common practice. The ores treated in this plant have from the beginning come from mines owned and operated by the company or have been custom ores purchased in the territory tributary to the plant. The treatment of custom ores is an important service to the small producer who does not have sufficient tonnage to warrant a plant, and serves to increase the tonnage of the operator of large properties, thereby helping to reduce

Jan 1, 1937

By Alan F. Stewart, Douglas R. Piteau, Dennis C. Martin

Three examples of open pits where toppling failure controls the stability and design of the slopes are described. Two examples involve the design of overall slopes in base metal mines. The third example concerns the analysis and design of remedial measures to prevent toppling failure from occurring in a critical slope in a coal mine. The analytical techniques for assessing toppling failure on a rational basis are discussed for the three examples. This includes an assessment of the important parameters which govern the stability for the toppling failure mode. The geological setting and input data for each example are described, as are the important external or limiting factors pertinent to the sites in question. A statistical cumulative technique was used to assess one of the most important input parameters in the two examples involving overall slope design. Both deep-seated toppling failures, involving the entire slope, and shallow bench failures are considered. Results of the stability analyses and their related engineering significance with regard to slope stability and design are discussed. A sensitivity analysis of various parameters is effectively utilized. Design charts are developed and evaluated accordingly. In the example where toppling failure was unavoidable, the rationale for design of stabilization techniques to prevent toppling is discussed.

Jan 1, 1983

By Ralph E. Davis, Lyon F. Terry

The rapid expansion of the natural gas industry in this country during the past three or four years has necessitated the construction of a number of long and comparatively large diameter high-pressure pipe lines This period of expansion and construction is still at high tide, and the current year will doubtless surpass all prior years in mileage and capacity of gas line installation. The fundamental economics of the business of long-distsrier transportation of natural gas may be briefly and simply stated, although most careful consideration must be given the actual determination and integration of the several more important factors which determine the ultimate success or failure of such a project. Reduced to its simplest form, a sound natural gas transportation project requires: 1. A competent source of gas, where the combination of quantity of gas available, cost of production, and longevity meet the given requirements. 2. A market, reasonably certain to endure in the face of any probable competition, of satisfactory size and price, and having a sufficiently favorable load factor. 3. A cost of installation of pipe line systen and an operating cost such as will, with honest and reasonably efficient management, afford a net operating return sufficient to attract the necessary capital required. In a11 new projects of this kind it is necessary that thehe three cssentials to ultimate success be assured. Hence the necessity of competent surveys of gas supply, and of market, both industrial and domestic. The prudent engineer will allow for "factors of safety" in reaching his conclusions just as he would in the design of a bridge. This paper deals primarily with but one of the major considerations enumerated above, I. e, the economic design of the pipe line system. The "pipe line system" will be considered to include (1) the pipe Iine, and (2) a series of compressor plants along the pipe line for maintaining

Jan 1, 1929

By S. B. Patterson, A.R. Amos

Log washers have been used for many years in the washing of clay iron ores, phosphate rock and manganese ores, but not until the past 15 years have they been employed to any extent in the preparation of aggregate materials and fluxing stone. For a machine of such importance where tenacious clay or soft rock must be eliminated, there are few data generally available. The purpose of this paper is to set forth the results obtained from several operations, together with a few suggestions for planning a specific installation. Where the material to be washed out consists of loose surface soil, silt, or small amounts of quickly soluble clay, there is little competition with other forms of washers, because greater power and maintenance are required for the operation of log washers, but where the foreign matter is a stiff clay, such as occurs with high-calcium limestones and in marginal gravel deposits, the ability of other kinds of washers to eliminate completely the hard clay balls is at least uncertain. Then the log washer comes into its own field, for with the breaking and churning action of the logs it will clean out the toughest clay. Even with material from the hydraulic dredge, if it contains tough clay, the log washer is desirable unless the gravel is subjected to a costly soaking and rehandling process. Recently there has been a considerable development in other types of machines to accomplish these results but it is not within the scope of this paper to make comparisons between competitive types, but to present the best obtainable data on log washers only. From the primitive design that gave it its name, a long log hewn from a tree, with paddles forged to shape from strap iron and attached by lag screws, the log washer has gradually been developed to the present all-steel type. As now manufactured, the log washer consists essentially of two built-up logs on which are mounted a series of paddles, carried by shafts fitted at the ends of the logs on bearings fastened outside the enclosing steel box, or trough, which is set at an angle of about 5" to 10" and into which the material is fed. Stuffing boxes at the places where the shafts pass through the box at the lower end are equipped with water-

Jan 1, 1938

By A. P. Boller

In the victories of peace as well as of war, the science of engineering has played a prominent, if, indeed, not the leading part. While it might be interesting, and food for profitable thought, to trace the development of engineering from early times in its bearings upon the social betterment of mankind, it will be sufficient on the present occasion to suggest a few thoughts that it is hoped will aid the unprofessional listener to an appreciative consideration of the subject-matter laid down for to-day's discussion, and possibly lead the professional brother to a higher conception of the profession to which he belongs. Since the advent of the railway era, it is difficult to grasp the sequence of historic events that have led to the wondrous derelopment of mechanical science, making possible the civilization that is our daily boast, and opening up a vista of future intellectual and moral advancement among the nations of the earth, 'before which the imagination becomes hopelessly lost. Even now, looking back over a period of only half a century, we often fail to realize the vast change in the relations of individuals and nations to each other., brought about by the results of those mechanical discoveries which, having made the whole world kin, exercise a resistless levelling influence that bears fruit politically in the spread of republican ideas, and morally in the elevation of the individual through the facilities given to the dissemination of Christian ideas and general intelligence. In this view, it seems almost like a work of supererogation for a body of representative men of one department of that science to which the whole world owe. so much, to meet here at the centre of our national life to plead not only for a practical recognition of the national importance of the work to which their lives are devoted, but also for national aid, on a scale beyond that of private effort, to the end that mechanical science may be carried to a higher plane than ever yet attained, each step on the way being of material benefit to every man, woman, and child in the community. Possibly this is strong language, but none too strong when we consider that the work for which we plead is one affecting not only vast scientific and commercial interests, but also human life, to a degree little ap

Jan 1, 1882

By A. R. Amos, S. B. Patterson

Log washers have been used for many years in the washing of clay iron ores, phosphate rock and manganese ores, but not until the past 15 years have they been employed to any extent in the preparation of aggregate materials and fluxing stone. For a machine of such importance where tenacious clay or soft rock must be eliminated, there are few data generally available. The purpose of this paper is to set forth the results obtained from several operations, together with a few suggestions for planning a specific installation. Where the material to be washed out consists of loose surface soil, silt, or small amounts of quickly soluble clay, there is little competition with other forms of washers, because greater power and maintenance are required for the operation of log washers, but where the foreign matter is a stiff clay, such as occurs with high-calcium limestones and in marginal gravel deposits, the ability of other kinds of washers to eliminate completely the hard clay balls is at least uncertain. Then the log washer comes into its own field, for with the breaking and churning action of the logs it will clean out the toughest clay. Even with material from the hydraulic dredge, if it contains tough clay, the log washer is desirable unless the gravel is subjected to a costly soaking and rehandling process. Recently there has been a considerable development in other types of machines to accomplish these results but it is not within the scope of this paper to make comparisons between competitive types, but to present the best obtainable data on log washers only. From the primitive design that gave it its name, a long log hewn from a tree, with paddles forged to shape from strap iron and attached by lag screws, the log washer has gradually been developed to the present all-steel type. As now manufactured, the log washer consists essentially of two built-up logs on which are mounted a series of paddles, carried by shafts fitted at the ends of the logs on bearings fastened outside the enclosing steel box, or trough, which is set at an angle of about 5" to 10" and into which the material is fed. Stuffing boxes at the places where the shafts pass through the box at the lower end are equipped with water-

Jan 1, 1938

By Clarence E. Sims, Donald W. Williams, George A. Moore

INTRODUCTION DURING the past several years the steel casting industry has made studies of heavy castings in which the test bar has been taken from heavy sections rather than from attached or separately cast coupons. It has been noted that the ductility properties of these heavy sections are often lower than those normally expected. Such lowered ductility is usually accompanied by a spotty test bar fracture and the ductility values often can be greatly improved if a low-temperature aging treatment is given to the casting. A loss of ductility of this type is considered "abnormal," since it is not accompanied by an increase of tensile strength or hardness, and "temporary" when the ductility can be restored by aging. The cure of such an abnormal condition represents a real improvement in the quality of the steel. Some hundreds of previous investigations, largely qualitative in nature, have established beyond reasonable doubt that hydrogen is normally present in newly manufactured steel and that this gas, in small amounts, can cause a temporary abnormal loss of ductility. The commonly observed association of high gas content and low ductility has given strong evidence for the presumption that hydrogen, possibly assisted by other gases, is the primary cause of the low ductility observed. Accordingly, the Steel Founders' Society of America has, since Nov. 1, 1944, sponsored investigations at Battelle Memorial Institute whose primary objective is to obtain quantitative information on the relation of the amount of hydrogen and nitrogen in steel, together with associated methods of steelmaking and treatment, to low-ductility effects and porosity. In order that these investigations might proceed on a quantitative basis, hydrogen analyses of a precision considerably higher than any previously reported in the literature were necessary. The method chosen was selected entirely on the basis that it had the highest probability of freedom from uncontrollable errors and will be described in detail in another publication.1 Briefly, the method used consisted of the hot extraction of solid pieces of steel weighing from 45 to 50 g in a highly evacuated quartz tube maintained at 1050°C (1925°F) for a period 0f approximately 40 hr. The greatest precautions were taken to eliminate blanks and insure a sound gas-collection system. Vacuum and temperature conditions were maintained automatically. Mercury-filled risers were used for the introduction of samples in order that the system could be degassed thoroughly in

Jan 1, 1948

By O. W. Ellis

In view of the extensive use of the brasses and bronzes in engineering practice it is indeed surprising that so little scientific work has been done on the oxides in these alloys. Recognition of the ill effects of these compounds is universally accorded, both in foundry procedure and in such specifications as cover the melting of these useful mixtures. In the latter, limits, for example, are placed on the proportions of scrap metal In the charge, and clauses governing the use of fluxes are included, the addition of fluxes to the charge being made with the object of avoiding oxidation during the process of melting and of subducing and separating non-metal-lic matter from the melt.1 In the manufacture of brass it occasionally, though rarely, occurs that the virgin metals, copper and zinc, alone arc used. In the event of virgin metals being employed, that of the higher melting point is always melted first. If it is melted under suitable conditions, little or no oxidation will occur. Whether oxidation has occurred or not, however, can best be determined by microscopic examination of a sample taken from the melt. Avoidance of Oxidation in Furnace Practice When melting virgin copper in crucible practice, the avoidance of oxidation is not difficult, nor is it hard to forestall trouble in the electric furnace. In gas-fired furnaces of the barrel type, however, the avoidance of oxidation is almost impossible, no matter what the condition of the flame, the flux employed, or the amount of charcoal included in the charge. Copper melted in furnaces of this type is almost invariably so highly oxidized as to requirc very considerable additions of such deoxi-dizers as, for example, silicon copper to render it free from cuprous oxide. As a result,, the castings produced are decidedly inferior, on account of the. large amount of silica which is engendered in the metal as a result of the reaction, Cu2O + Si = SiO2 + 2Cu. The deoxidation of such oxidized copper could, of course, be effected by means of zinc with, however, even more disastrous results.

Jan 1, 1930

By W. O. Philbrook, A. H. Jolly, T. R. Henry

In the course of a study of slag-control methods, the authors devised a laboratory technique by which the basicity of basic open-hearth furnace slags could be estimated with sufficient accuracy to make the method of possible interest for slag-control purposes. The process consisted of measuring the slight basicity of an extract of the powdered slag in water. The procedure was presented, for the benefit of those who might care to experiment with it, in a paper submitted in the 1944 McKune Award Contest and presented at the 1944 Open-hearth Conference in Pittsburgh.' Interest expressed at that meeting and favorable operating experience with the method at a neighboring plant, as described in a related paper by Michael Tenenbaum and C. C. Brown,; have encouraged us to present further details of the development, technique, and pitfalls of the method and some additional data not included in our first report. At the outset it must be admitted that this method of estimation of slag basicity is not perfect; neither is any other that we know of. It is subject to somewhat greater errors than would be desirable, but compares favorably with other techniques in this respect. It has the disadvantage that it places the final determination of slag basicity in the hands of a laboratory technician rather than the furnace oper- ator, although it can be operated in a control laboratory adjacent to the furnaces. It requires close attention to certain details, as do most laboratory procedures. On the favorable side, it eliminates the "human factor" of personal judgment inherent in estimation from pancakes or powdered samples. The procedure can be placed in practice much more rapidly and presents much less of a training problem than visual methods of estimation. The principle and operation of the method are so simple that it would not be surprising if others have experimented with the same or similar procedures, but we are not aware of any prior publication of details. Our own shop has been operating fairly successfully for several years with the aid of slag pancakes. Since the past year or two have not been favorable for the expenditure of time and energy where the need was not urgent, we have not introduced the new practice for actual slag control and hence do not have extensive operating data. In presenting this method, therefore, we make no claims as to theoretical justification nor guarantees as to practical applicability, but offer it as an empirical observation. We believe it has sufficient merit to warrant its investigation by those just instituting a slag-control program or in search of supplementary methods for judging slag basicity Principle of the Method It is well known that when burnt lime or slaked lime is shaken up with water it

Jan 1, 1945

By James Herbert Bartlett

I desire, very briefly, to call the attention of the Institute to the iron trade of the Dominion of Canada. A wonderful development is now going on in Canada. The completion of the Canadian Pacific Railway, and the numerous extensions of the various railways all over the country, combined with the progress made in nearly every kind of manufacture, is drawing attention to the field offered in Canada for the profitable employment of capital, and specially to the opportunity there is for the manufacture of iron. In a paper presented to the Institute at the Halifax meeting,* the writer gave a review of the varions attempts to manufacture iron in Canada. The facts then presented were not such as to offer much encouragement to any one to embark in similar enterprises under the conditions then existing, but, happily, these conditions are now changed, and an early development may be anticipated. There are two reasons which make the present time an appropriate one to direct attention to the field offered for enterprise in this direction, the first being the very favorable reports of the experts who examined and reported on the exhibit of minerals at the Colonial and Indian exhibition, held in London, England, last year. The exhibits there of coal and iron attracted so much attention that at the request of the Iron and Steel Institute a paper on the " Ironmaking resources of our Colonies as illustrated by the Colonial and Indian Exhibition," was prepared and read at the last meeting of the Institute.? This report of 135 pages is very exhaustive, and the conclusion arrived at, so far as Canada is concerned, is, that she has in many parts of the country every natural facility for the manufacture of iron. The second and more important reason is the recent change in the Canadian customs tariff inaugurated in May last. The tariff is now generally two-thirds of the American tariff, in addition to which the Government, in order to encourage the manufacture of iron, grants a bounty upon pig-iron made in Canada out of Canadian ore.

Jan 1, 1888

By R. W. Gurry

IN the course of a series of measurements of the rate of diffusion of carbon in austenite at about 960°C. (1760°F.) and 1110°C. (2030°F.), it became necessary to determine carbon concentration when austenite is saturated with graphite, because of indications that the hitherto accepted value of the solubility of graphite in this temperature range is too low. Specimens of carbonyl iron were saturated at temperature in a hydrogen-toluene atmosphere which was in equilibrium with graphite. The carbon content of the steel was measured either by combustion or by the loss of weight after substantially complete decarburization in an atmosphere of hydrogen saturated at room temperature with water vapor. The absence of carbide or graphite as a phase at temperature was demonstrated by microscopic examination of saturated specimens that had been drastically quenched. The mean result of concordant measurements is that gamma iron saturated with respect to graphite contains 1.39 per cent carbon at 957°C. (1755°F.) and 1.89 per cent at 1110°C. (2030°°F.). These two values, plotted along with what appears from the literature to be the best value (0.69 per cent) at the iron-graphite eutectoid temperature (738°C. or 1360°F.), yield a curve that is almost linear, and which, continued upward through a short interval, leads to a limiting solubility of 1.98 per cent at the iron-graphite eutectic temperature1135°C. (2095°F.) instead of the commonly accepted value of about 1.7 per cent. EXPERIMENTAL PROCEDURE The samples of carbonyl iron, with the exception of those for microscopic examination, were cylinders 3.8 cm. long, 0.475 cm. in diameter. They were placed in a graphite holder and suspended in a vertical furnace, the temperature of which was controlled precisely by means of the resistance of the platinum winding.1 In the empty furnace the range of temperature over a distance of 4 cm, at the heat center was 9°C. (16°F.) but at a given location the temperature remained within ±0.5°C. (0.9°F.); it was measured by inserting a platinum-rhodium couple calibrated at the melting point of palladium, 1555°C. Since the presence of the sample probably improved the uniformity of temperature, it was decided to consider the average temperature of the sample to be 3°C. lower than the maximum measured in the empty furnace with the same setting of the controller. Data were obtained in the vicinity of two temperatures, 960°C. (1760°F.) and 1110°C. (2030°F.). The samples for microscopic examination, 2.2 cm. long, 0.475 cm. in diameter, were suspended individually on pure iron wire; for these no temperature correction was applied. The carburizing gas passed into the furnace was dry, oxygen-free hydrogen saturated at room temperature with

Jan 1, 1942

By Nelson Severinghaus

Crushed stone leads all industrial mineral, except cement in annual value of production in the United States. It is also interesting to note that crushed stone value is exceeded only by that of fuels, cement, and iron ore among all mineral products of this country. An industry which started with hand-sledging to produce smaller sizes of broken stone for hard surfaced improvement of roadways as designed by McAdam in England about 1815 has grown into a complex industrial giant. Most of this growth started with the invention of a mechanical rock crusher just under one hundred years age (1858) by Eli Whitney Blake. This invention made possible the production of greater tonnages of smaller sizes of broken stone and greatly accelerated its use for Macadam road pavements and for railroad ballast. Stones Used for Crushing All three of the major geologic classifications of stone, sedimentary, igneous, and metamorphic, are widely used in the production of crushed stone. Satisfactory physical and chemical properties can be found in each type so that economic availability becomes the prime determinant for development. Table 1 lists more common rocks of the three main groups with average values of specific gravity and toughness as measured by Deval test. This widely used classification was suggested by C. E. Lord, of U. S. Bureau of Public Roads. The physical properties were compiled by D. O. Woolf in "The Results of Physical Tests of Road Building Rock," U. S. Department of Agriculture, Bulletin 76. It should be noted that the figures given in Table 1 are averages. Very substantial variations in the physical properties of rocks within any one classification will occur. The solid surface of the earth was first made up of igneous rocks resulting from the solidification or crystallization of molten material upon cooling. These igneous rocks were disintegrated into sand, clay, and gravel by the weathering action of wind, water, chemicals, [ ] and temperature changes. The products of weathering were transported by wind and streams until they reached less turbulent areas such as oceans or lakes and were deposited. Chemical deposition between grains of sand or clay or the physical action of pressure and heat then solidified them into sedimentary rocks

Jan 1, 1960

By R. V. Wheeler, W. Francis

Of the methods that have been used for studying the chemical composition of coal, attack by reagents has not, in general, yielded much information. Most of the reagents used have been strong oxidants such as nitric acid or Schulze's solution. The use of a milder oxidizing agent, such as air at low temperatures, enables progressive changes in the character af the coal substance to be studied and thus helps toward an understanding of its constitution. British bituminous coals frequently have a banded structure. These bands (of four types) can be separated one from another and have been found to possess markedly different chemical characteristics, even when taken from contiguous portions of the same lump coal. It has been found convenient to give each of the ingredients of banded coal a distinctive name, more or less descriptive of its appearance, and the study of the chemistry of bituminous "coal" in England has resolved itself into a study of each ingredient separately. The coal chosen for this work was taken from the Top Hard seam at East Kirkby colliery, Nottinghamshire, a detailed chemical analysis of which has been recorded by Baranov and Francis.' The banded structure was well marked and the bands could readily be separated. The research was confined to the brilliant vitreous bands (vitrain), the dull hard bands (durain) and the "sooty partings" main); for previous work had shown that the fourth type, to which the name clarain has been given, is intermediate in character, chemically, between vitrain and durain. The method of experiment was, briefly, to draw a slow current of moist air through weighed samples (50 gm.) of the three ingredients, vitrain, durain, and fusain, in the form of powder (through a 60-mesh and on a 90-mesh sieve) contained in glass tubes which could be maintained at a constant temperature during prolonged periods. After passing through the coal, the air bubbled into a measured volume of

Jan 1, 1925

By William Romanoff

IN AN ARTICLE on "Recovering Smelter Dust and Oxide," published in the Engineering and Mining Journal (Vol. 131, No. 2), the authors briefly described some dust-recovery equipment and its operation at a secondary-metals brass-smelting and refining plant. A description of our experience in overcoming certain operating difficulties may prove of interest or value to those who are confronted with some of the same problems or who should equip their furnaces with dust-collecting equipment. The dust loss from reverberatory smelting and refining of brass con¬sists largely of zinc, with smaller percentages of lead, tin, and copper in the order named. At the Kramer plant, the fume discharge from the two stacks amounted to 3 to 4 tons of solids per day, making a dense smoke. With dust equipment in operation, the discharge from the stacks is invisible and approximately 2500 lb. of zinc and other metals is recovered daily thereby from each furnace operating.

Jan 1, 1933

By Clarence Zener

THE heat-treatment of steels will not pass from the stage of an art into that of a science until the mechanism of the phase transformations associated therewith is thoroughly understood. Such an under- standing will involve two distinct types of inquiry: (I) the direction of the trans- formation, (2) the speed of the transformation. The first type of inquiry, which involves only the equilibrium relations between the various phases in steel, is the subject of the present and of a succeeding article; the second type, which involves the kinetics of transformations, will be the subject of a later article. In order that a theory of equilibrium relations may give useful information, certain experimental data must be put into the theory. It is customary for these data to be of a thermal nature. In the system discussed here in steel such thermal data are very scarce. In medium-alloy steels another type of data might possibly be used. In these steels the concentration of solute is so low that it may be possible to use the approximation of dilute solutions, an approximation that leads to linear relationships. The unknown functions, or constants, may then be determined in some cases from the binary iron- alloy system and in other cases from the ternary iron-carbon-alloy system. From the functions, or constants, so determined may then be computed the equilibrium relations in more complex medium-alloy steels. In the present article this second approach is used, the necessary experimental data being obtained from the simple binary and ternary equilibrium diagrams. FUNDAMENTAL EQUATIONS In this article are derived the equilibrium relations between the gamma, alpha and cementite phases. In these three phases all important alloying elements except carbon form substitutional solutions, each alloying atom occupying a potential site for an iron atom. Carbon, on the other hand, forms an interstitial solution. In the face-centered cubic gamma phase, the interstitial positions are at the center of the unit cube and at the centers of the cube edges. There are therefore four interstitial positions per unit cell, or one per iron atom. In the body- centered cubic alpha phase, the interstitial positions are probably at the face centers, and also at the centers of the edges, which are crystallographically equivalent to the face centers. There are therefore six interstitial positions per unit cube, or three per iron atom. In cementite, (Fe, Alloy)3C, the carbon atoms may be regarded as filling all the lattice positions of a given type. The introduction of the fundamental equations of equilibrium has presented the author with a quandary. These equations are formally so similar to other equations that have been derived1,2 for related systems that they may appear to some readers

Jan 1, 1946

By G. R. Fitterer

By means of the C-Sic thermocouple1, liquid metal temperatures have been found to vary much more than was previously supposed, and fortunately these variations can be directly associated with some of our former knowledge which combined to form the "art" of liquid-metal manipulation. Commercial Development of This Device Several types of installations are operating in different plants. There are so many variables in steel plants in regard to operation, procedure, arrangement of pouring platforms, ladles, etc., that most of the installations now in service in this country are "tailor-made"; nevertheless, it is felt that satisfactory gains have been made, inasmuch as each installation has indicated some effect of temperature upon the metallurgical operation, and has pointed the way toward technical and financial benefits. In most cases, it has been necessary to accumulate the temperature data until sufficient metallurgical information is available for the drawing of conclusions. When mechanical difficulties have been eliminated, a distinct correlation of these factors has been obtained. The installations now in service are used for the determination of temperatures in the basic open-hearth furnace prior to tapping and in ladles from both acid and basic furnaces prior to pouring. Some of the installations are in shops making the higher priced steels; others are in "tonnage shops." The errors of human element, smoke screens and emissivity corrections connected with the use of the optical pyrometer do not affect the C-SiC thermocouple readings. The accuracy of the C-Sic thermocouple and the temperatures measured are discussed later in this paper. Temperature Variations or Liquid Pig Iron One well-known discussion between the blast-furnace and open-hearth (or Bessemer) departments has occurred intermittently for more

Jan 1, 1936

By Burton H. Boyum

Greater depth of exploration drill holes and increasing cost of drilling have been principal factors in reviving interest on the Mar-quette Iron Range in controlled directional drill-hole deflection. This deflection is obtained by the application of the Hall-Row wedging technique. Modifications were made in the technique and equipment in the effort to simplify and strengthen the procedure. The practice is similar in many respects to the oil well type of deflection with a whipstock. Introduction The deflection of diamond drill holes by wedging was a widespread practice in Canada, South Africa and the Lake Superior District as early as 1907 to 1920. Several basic schemes were used, with local variations.' The deflecting wedge assembly was the idea of Mr. Welldon and Mr. Payne-Gallwey operating under the supervision of Mr. William Gallagher of Johannesburg, South Africa. All schemes employed some means of plugging the old hole. A footpiece of various styles was placed in the hole on the plug. In some methods, the orientation of this piece was determined before placing the deflecting wedge. Some techniques permitted continuing the hole the same size after wedging, while others necessitated a size reduction. Interest in wedging diamond drill holes in the Lake Superior District waned after 1920. The Hall-Row patented system for deflecting holes was developed in Canada about 1918.2 Interest centers on the wedging process for the following applications: 1. Maintaining a given course and inclination of the drill hole. 2. By passing an obstruction in a drill hole. 3. Resampling an ore body. 4. Exploring an area overlain by surface conditions not favorable to drilling. During the period of 1913 to 1920, The Cleveland-Cliffs Iron Co. used the wedging technique under a variety of conditions. In general, the practice was not applicable again until 1946. Meanwhile the Hall-Row system of drill-hole deflection survived years of application as the best technique available. In the intervening years, our depth of exploration has increased as well as the overall cost of drilling. As exploration becomes deeper, there is the possible economy of cutting the ore body at a moderate distance from the parent hole without redrilling from surface. Thus a branch hole started near the mid-point of a deep hole can reach the ore horizon at a considerable offset from the parent hole. This permits a greater interval between surface drill holes as drilling becomes deeper. Our interest revived in the subject and a wedging program was initiated. General Description Results The maximum theoretical angular deflection possible, based on the deflecting

Jan 1, 1949

By Charles T. Baroch, Charles J. Baroch

In 20 years of commercial development, nuclear reactors have demonstrated that they are a safe, dependable, and economical source of power. Operating experience with commercial power reactors has firmly established nuclear power as a practicable source of energy. For both boiling-water (BWR) and pressurized-water (PWR) reactors, performances to date have generally met design predictions. Furthermore, it has become possible to analyze and understand the nuclear, chemical, and physical behavior of this class of reactors. The United Kingdom has had similar success with gas-cooled reactors. The Experimental Boiling Water Reactor (EBWR), the first United States experimental power reactor, began operation in 1956. It proved to be capable of supplying 4500 kw (kilowatts) of power. This reactor was followed in 1957 by the Pressurized Water Reactor at Shippingport, Pa. It was the nation's first full-scale central-station nuclear power plant and the first in the world designed exclusively for the production of civilian electric power. The Shippingport reactor was originally designed to produce 60 megawatts (MW) of electricity, and it was increased to 100 MW in 1964. In 12 years of operation, this reactor generated over 4.5-million MW-hr of electricity in spite of many shutdowns for experimental alterations. By 1969, a total of 15 central-station nuclear power reactors were operable in the United States with an aggregate electrical capacity of over 4200 MW. Early in 1964, Jersey Central Power & Light Co. announced plans for constructing a 515-MW nuclear plant at Oyster Creek, N.J., to be built without government financial assistance. The company stated that a nuclear plant had been selected competitively with fossil fuel. Their economic analysis stated that the plant would generate electricity at less than 4 mills per kw-hr, competitive with coal at 200 per million Btu (British thermal units). Coal cost in 1964 for that region averaged 26.00 per million Btu. The Jersey Central report created wide interest in public-utility circles; nevertheless, no other nuclear plants were announced in 1964. However, in 1965, six nuclear plants were announced by utilities, followed by 26 in 1966, 29 in 1967, and 10 in 1968. By Sept. 30, 1969, 97 reactors were operable, being built, or planned. The cost of these, all committed by electric utilities, was estimated at about $12 billion. When constructed, they will have an electrical capacity of 72,000 MW. The unprecedented surge in power reactors that started in 1965 tapered in 1968, and only seven reactors were announced in

Jan 1, 1976

By R. M. Leibrock, C. W. Ziemer, R. P. Vincent

The Stanolind flowmeter, which employs a hot-wire anemometer connected in a Wheat-stone bridge circuit, has proved useful for determining the relative productive ability of individual sand members of gas wells. The operation of this instrument in measuring gas velocities in the well bore above each producing member has provided both a direct and accurate means of analyzing reservoir performance. Results of tests conducted with the well flowmeter in the Hugoton gas field of western Kansas have indicated some rather unusual production characteristics. In two cases it was found that all or the greater part of the total gas produced was coming from one section in wells where four "pay" sections had been perforated individually. These actual measurements contradict in many instances the indications of data obtained from electric logs and from core analysis; the fact that these latter sources often give incorrect results, demonstrates the necessity of a method, such as is provided by the well flowmeter, for accurately determining the amount of gas coming from each producing member. Introduction In any gas well where a number of pay sections have been perforated individually and are producing to a common outlet, the question arises as to the relative amounts of gas being passed through each set of perforations. In the past it has been the policy to depend on core analysis to estimate relative productivities, or, where the sections were not cored, to obtain some idea of production characteristics from electric-log studies. The weaknesses in these methods are readily apparent and indicate the need for more reliable means of measuring gas flow from each zone. The Stano-lind flowmeter* was developed for this purpose. Preliminary tests were made with the instrument in the Katy gas field near Houston; however, the bulk of the routine work with the well flowmeter has been confined to the Hugoton gas field in western Kansas, where results obtained have been encouraging. A description of the instrument, the field technique employed in testing, and a few of the results obtained in the Hugoton area are discussed in this paper. Description or Instrument The well flowmeter is 1¾ in. od and 7 ft long; it is entirely self-contained, can be run through tubing as small as 2 in. id in wells with high pressure (4500 psi) and temperature (210°F) and is lowered on a wire line commonly used for other instruments of the bottom-hole type at falling rates up to 500 ft per minute. It will detect gas flow as low as 10 ft per minute linear velocity, and yet withstand and record velocities of 1000 ft per minute without damage to the detecting element. Killing the well is not required nor desirable for running a production profile when using the instrument, and it is necessary to stop flow for only a short time. The detecting element of the instrument is a hot-wire anemometer connected in a

Jan 1, 1948

By M. Bevis, A. G. Crocker

A. G. Crocker and M. Bevis (Battersea College of Technology)— Richman and Richman and conard17 have recently published the very interesting results of their studies on the plastic deformation of Fe-Ni-C martensites and of an Fe-5 wt pct Be alloy. Other work on the range of Fe-Be alloys containing between 16 and 27 at. pct Be has also been reported by Richman." One of the fascinating features of this work is that the materials investigated deform primarily by means of twinning and that several twinning modes are operative in addition to the well-established (112 ) mode of bcc materials The composition planes of these unusual twins were determined using a single-surface analysis and reported as (0131, "{045)" or "{089)", and It is now thought1' that the "{0,1,13)" habit reported for the Fe-Ni-C alloys'' is more likely to be near "{127)". Although the full twinning elements of these unusual twinning modes could not be determined directly from the experimental results, the authors attempt to deduce the elements by considering twin intersectionslQ and by using the projection technique of Jaswon and Dove. The basic assumption of their approach is that the (013) habits are truly rational planes but that the other habits are irrational and merely approximated to by the indices quoted above. They thus deduce that the twinning mode describing the (013) habit is either Type I or compound and that the modes describing the other habits are Type 11. This deduction must however be false as all twinning modes in cubic structures obeying the classical orientation relationships of deformation twinning must be compound. Type-I and Type-I1 modes can occur in all of the other crystal systems (indeed in the triclinic system compound modes are not allowed), but in the cubic system only compound modes can arise. This fact, which does not appear to be well-known, fol- lows immediately from the relations between the four twinning elements defining a twinning mode. Thus for a Type-I mode which is uniquely defined by the rational twinning elements K1 = hi and given by: where the summation convention of the tensor calculus has been adopted. For cubic materials the metrics and reduce to the unit tensors and j so that we have It is clear from these equations that both ki and ui must take on integral values; i.e., Kz, and ql must be rational, if hi and vi are integers, i.e., if K1 and are rational. Thus for cubic materials a Type-I mode must degenerate into a compound mode and the same result also arises for Type-II modes. The apparently irrational habits observed by the authors can thus not be explained in terms of Type-I1 twinning if the classical laws of deformation twinning are to be obeyed. An alternative explanation of the irrational habits is that they may arise from twinning modes with four irrational twinning elements. These modes, which do not obey the classical orientation relationships associated with deformation twinning, have been shown to arise as the result of double twinning processes in magnesium,22 but may also describe a simple shear on an irrational plane in an irrational direction. Indeed double twinning processes in bcc

Jan 1, 1963