Search Documents

By M. A. Orehoski, J. M. Hodge

It is now generally conceded that if a steel is to develop optimum physical properties in the conventionally quenched and tempered condition, the microstruc- ture after quenching should consist wholly of martensite; and that transformation of austenite to intermediate-temperature products during quenching will have a deleterious effect upon the physical properties, particularly the toughness, of the tempered material. This implies that, in order to obtain the optimum physical properties from a given steel, its "harden-ability " should be high enough to suppress all transformation except that to martensite under the heating and quenching conditions to which it will be subjected, and this premise is probably the most important reason for hardenability control. However, the criterion of hardenability that at present is most widely accepted and used is based on a microstructure of 50 per cent martensite. This criterion, which was suggested by Grossmann,' does have considerable justification. It may be readily measured by a fracture or etch test and, since it represents the point at which the hardness is changing most rapidly with variations in cooling rate, it may be determined empirically from a hardness-depth curve by determining the point of steepest slope (the inflection point). Furthermore, in plain carbon steels or in steels of low hardenability, the difference in hardenability expressed in

Jan 1, 1947

By Oliver Bowles

While vast quantities of limestone and dolomite are used in metallurgy, the estimated production in 1926 being 23,860,000 tons, there are many problems connected with their use which have not received adequate study. The literature of metallurgy is notably lacking in comprehensive discussions of fluxing or furnace stone. Approximately 900 lb. of limestone is used for every long ton of pig iron produced in the blast furnace, but this important constituent of the charge receives little atten. tion compared with the intensive study that has been applied to ores and fuels, the other important constituents of the charge. In an effort to elucidate some of the doubtful points, the writer has made a wide review of metallurgical literature, and has had the disappointing experience of finding not more than a paragraph or two on metallurgical stone for each two or three thousand pages of literature reviewed. Furthermore, the limited information supplied is in some instances contradictory and even absurd. For example, a correspondent in a reputable metallurgical magazine classifies magnesia and silica together as impurities in flux " that must be melted and run off as slag." From the furnace operator's viewpoint it is desirable that as complete knowledge as possible be obtained concerning the effects of chemical composition and physical character of the stone on its action in the furnace and on the quality of the metal produced. A better knowledge of these features is advantageous also to the quarry operator in that it enables him to work more intelligently in producing stone that will best satisfy the metallurgists' requirements. The following pages comprise a brief compilation of data now available. Much of the information is well established and probably acceptable to most metallurgists. On some points there is room for debate, and the chief purpose in presenting a paper at this time is to arouse discussion which will throw more light on controversial points and thus assist the author in preparing a more comprehensive and accurate discussion of metallurgical limestone problems.

By A. F. Taggart, F. E. Beach

The flotation process for the concentration of ores is a method by means of which one or more of the minerals in the ore (usually the valuable ones) are picked up by means of a liquid film and floated at the surface of a mass of fluid pulp. Here they are separated from the other minerals, which remain immersed in the body of the pulp. In general, the minerals which are floated are sulphides of metallic luster, but some other minerals of metallic luster such as graphite and some sulphides with adamantine luster, such as sphalerite and cinnabar, are amenable to treatment by the process. The importance of flotation lies in the fact that it is primarily a "slimes process" by means of which the particles of valuable mineral, too fine for efficient gravity concentration, are saved with a high percentage of recovery. Recoveries in the mills treating low-grade copper sulphide ores have been advanced 10 to 20 per cent. by the installation of the process and similar increased savings have been accomplished by the same means in mills treating sulphide ores of zinc and lead. When finely ground ore containing sulphides mixed with a siliceous or earthy gangue is brought gently onto the surface of a body of water, in a direction forming an acute angle with the surface of the water, a considerable portion of the sulphide constituent of the ore floats on the surface of the liquid, while the gangue sinks. This is the so-called film flotation, exemplified by the Wood and Macquisten processes. When gas bubbles are introduced into a fluid pulp composed of finely ground ore and water, to which has been added (1) a small amount of certain oils, or (2) a small amount of certain acida or acid salts, or (3) a small amount of certain alkalis or alkaline salts, or (4) a small amount of a mixture of oil with acid or alkali, the sulphide particles in the ore are brought to the surface on the gas bubbles. These collect in a froth

Jan 1, 1917

By Charles M. Behre

Under the caption "fault," geologists intend to include all mass movements of solid rocks over adjacent rock masses. When these are studied long after their origin, however, circumstances make it possible to recognize as "fault" only formations showing clear evidence of actual movement of one side with respect to the other. Necessarily the chief evidence consists of the offset of a vein, bed, or other key structure. Planes of movement parallel to the bedding, or nearly so, are recognized with difficulty or are overlooked and hence many important faults are wholly unrecorded. Indeed, among standard American references on structural geology, one alone emphasizes the importance of bedding-plane movements and that one only briefly1. For some time the writer, cognizant of this difficulty, has paid special attention to such movements, both as observed in the field and as recorded in the literature. It is believed that enough data are now at hand to justify a short discussion. Its purposes are fivefold. It is desired first to briefly classify and describe at least the more common kinds of bedding-plane faults, and second, to examine the causes and manner of their formation, at least in instances where the subject has not yet been well covered by other investigators. Third, certain by-products of bedding-plane movements are of such conspicuous importance to the economic geologist and mining engineer as to merit mention. Fourth, concrete illustrations should be placed before the reader in order to lend reality and to furnish a basis of comparison with his experience; such illustrations will necessarily be scattered through the text of this paper. They are only in part from the writer's own field observations. The fifth and prime objective of this paper is to direct attention to the great importance of movements on the bedding planes, in the hope that the recognition of such movements and their significance may simplify mining problems.

Jan 1, 1937

By Edmund B. Kirby

This meeting marks the point at which the long-standing dissatisfaction with the mineral-land laws, the innumerable protests against them, and the many isolated efforts to obtain relief, have developed into a general movement for their revision. That part of the mining industry which is affected by these laws has three general organizations which are able to speak for it: the American Institute of Mining Engineers, the Mining and Metallurgical Society of . America, and the American Mining Congress; all of which are represented in this meeting. In the series of able and thoughtful papers presented here, prominent men have discussed the evils of the present laws and some of the reforms which should be made in them. We all appreciate fully the ultimate value of these studies; but we are also painfully aware of the fact that discussion of this kind has been going on for a quarter of a century without any other effect than a steady increase in the mass of printed records stored on library shelves. In order to get any practical result we Gust induce an indifferent government at Washington to act, and to do this we must unite in pushing some practical plan whereby it may act in a simple and effective way and with the least possible amount of criticism or opposition. The actual question before us is not whether the mining laws are bad; for their evils and absurdities are not only beyond discussion but also beyond the resources of a temperate and dignified vocabulary. It is not what particular changes ought to be made; for it is premature to make . specific recommendations until there is some one to listen to them. Moreover, we all know that there are wisdom and experience enough available, and awaiting that time, for the creation of a code which would be a model to the mining world. The practical question now is, how to obtain the revision; and since the American Mining Congress has of late restricted its attention to this phase of the problem I wish as one of its representatives here to present its views upon the matter.

Jan 1, 1915

By M. L. Fuller

MOST commercial alloys undergo changes in phase composition after casting. This is a natural result of the fact that the alloys are not in a state of phase equilibrium as cast and phase changes will therefore take place, with more or less rapidity, in an attempt to attain equilibrium. The practical aspect of aging in zinc-alloy die castings concerns the changes in physical properties and in dimensions that may accompany aging phase changes. Harmful alterations have been reduced to a minimum and zinc-alloy die castings are being produced today that are so stable with respect to dimensions and physical properties that they are entirely suitable for most practical purposes1. In the first paper2 of this series, and in this paper, aging phase changes of zinc alloy die castings have been investigated and the possible influence of these changes on dimensional changes of the castings has been evalu-ated and compared with the dimensional changes actually experienced. The change of dimensions has been selected for practical comparison in these papers because the effect of phase changes on the dimensions of a casting is directly calculable; from X-ray crystal-analysis data of the phase structure. The die-casting alloys considered contain, in addition to zinc, 4 per cent of aluminum, about 0:03 per cent magnesium, and from 0 to 3 per cent of copper. It was shown in the former paper that the eutectoidal decomposition of the beta aluminum-zinc phase, while intrinsically capable of causing a considerable shrinkage, can have very little effect on the observed shrinkage of die castings because it takes place within a few days of aging, whereas the observed shrinkage continues for five weeks. It was therefore concluded that the other existing phase change,

Jan 1, 1935

By J. F. Wilson

Steady-state flow theory, previously applied to displacements with two mobile phases, is extended to cover down-structure flow involving three mobile phases: oil, gas and water. When used with normal reservoir fluid properties, the theory predicts the existence of four distinct flow regimes and the conditions under which each regime exists. The predicted behavior is verified by a parallel-plate model study. INTRODUCTION Special problems exist when a water flood is contemplated in a dipping reservoir having a substantial gas cap. Normally, the gas-cap region is one of very low oil saturation. If oil is moved into the gas cap during the flood, a loss in recovery results. Efficient recovery of the oil underlying the gas is therefore difficult. In two reported field water floods, injection into the gas cap has been used to solve these problems. At the West Norfolk Garr Sand Unit, injection into the upstructure region of the reservoir was made for the stated purpose of filling up the gas cap with water.' The purpose in the Sholem Alechem Fault Block "A" Sims Sand Unit was to form a continuous water barrier between the gas cap and oil band.' A laboratory model study preceded this flood and was described in the same publication. Both of these gas-cap water injections gave satisfactory results, but the published data are insufficient to allow generalizing to other field conditions. The present investigation was also undertaken to obtain results for a specific field problem. However, these results will be shown to be in agreement with an extension of the Dietz3-5 mathematical model to three-phase flowing systems. The agreement between the theory and the model studies indicates that the mathematical model can be used to describe completely the flowing system under some conditions, and to indicate the general type of flow to be expected under all conditions. FLOW THEORY The Dietz equations for two-phase flow are derived "' for the case of constant-velocity linear flow in a homog- eneous porous medium. The transition zone between the fluids is assumed to be of negligible extent so that the displaced and displacing fluids are separated by a sharply defined interface, as illustrated in Fig. 1. The density and mobility of the displacing fluid are constant over the region behind the interface, and the same properties of the displaced fluid are constant over the region ahead of the interface. To extend the Dietz equations to three-phase systems, we postulate the flowing system shown in Fig. 2 and determine the conditions under which it can exist. The

By Keith Leonard Sutherland

THIS paper is a study of the differential flotation of the sulphide minerals in the presence of salts of silver, lead and zinc. In practice, accidental activation due to these salts is more important than their use as reagents to replace copper sulphate. The general method of investigation has been based upon contact tests, the temperature of 35°C. being chosen in conformity with earlier work. Potassium ethyl xanthate and potassium amyl xanthate were selected as collectors and pure sulphide minerals were used. The experimental procedure has been outlined in earlier papers and all solutions were kept carbonate-free.'' Contact, or spreading of an air bubble, at a mineral surface indicates the presence of an adsorbed collector film. PURITY OF REAGENTS The xanthates were purified in the usual manner.1 Neither the cyanide nor the sodium hydroxide solutions contained sufficient carbonate to give a precipitate with barium chloride solution. The silver sulphate was prepared from pure silver nitrate by evaporation with concentrated sulphuric acid until there was no evidence of brown fumes. This solution was diluted and the difficultly soluble sulphate washed with water so that unchanged nitrate was dissolved. The resultant crystal-line powder was pure white. The lead and zinc salts were prepared by dissolving especially pure lead and zinc in C.P. nitric and sulphuric acid solution and the crystals drained. The standard solutions were checked by titration. It was felt desirable to use the sulphate radical wherever possible, but since lead sulphate was insufficiently soluble for the purpose of the experiments, it was necessary to use some other lead salt. A.R. copper sulphate was used without further purification. RESULTS The results are presented in the accompanying figures; the areas of noncontact (nonflotation) are shaded in Figs. 8, 9, 10 and 11; in the remainder they lie to the right of the curve. Zinc Sulphate The curves in Fig. I are to be compared with those for Fig. 2, for which zinc sulphate is absent. This comparison shows that the influence of the zinc ion is usually small. Its influence is more marked, however, for chalcopyrite in the absence of cyanide. The influence of zinc sulphate is also marked for copper-activated sphalerite, for which tests were made only in the absence of cyanide. The results are of importance in the separation of pyrite from copper-activated sphalerite when zinc sulphate is added in the lead flotation section (p. 204 of ref. I). Sphalerite does not adsorb the collector (i.e., become floatable) under the conditions chosen.

Jan 1, 1942

By Max C. Eastman, V. H. Wilhelm

California had a record year in production and drilling activity, but the results have not been sufficient to keep up with the enormous increase in demand due to war activity. During the year, 164 dry wildcats were drilled, 80 dry wells in proved areas, 31 gas wells, and 1158 successful oil-well completions for a total of 1433 wells, compared with a total of 765 in 1942. With new discoveries of only 20,000,000 and production of 283,000,000 bbl. for the year, total reserves of California oil have decreased more than 250,000,000 bbl. However, revised estimates of the reserves of old fields indicate an increase in the state's reserves of I00,000,000 barrels. The completion of 1158 wells has served only to maintain the maximum efficient daily rate of production at 800,000 barrels. There is evidence in many fields that oil is being withdrawn too rapidly to obtain the maximum recovery, and more rapidly than is conducive to good production practice. Statistics for 1943 as compared with I942 are shown in the table in the next column, Supply and Demand Steadily mounting needs of the military forces and increased industrial consumption raised total demand for all petroleum products on the Pacific Coast to 914,000 bbl. daily in 1943. That all-time record demand was 149,ooo bbl. daily higher than in 1942 and 214,000 bbl. daily above 1941 demand. Despite restrictions due to shortages of critical material, crude-oil production was boosted from 680,000 bbl. daily in 1942 to 779,000 bbl. daily in 1943, the highest level in 15 years. However, the new crude supply plus natural gasoline production and imports from other states totaled only 840,000 bbl. daily, leaving a deficiency between supply and demand of 74,000 bbl. daily. That shortage had to be made up by withdrawals from inventories, which had been steadily depleted during the previous four years. Aboveground reserves, which totaled 159,574,000 bbl. on Jan. I, 1939, were down to ~8.000,000, bbl. at the end of 1943. Significantly enough, the greater part of that decrease occurred during the last six months of I9437 when more than 23,000,000 bbl. was taken from inventories of both crude and products. Although the size of total inventories on Dec. 31, 1943 might appear substantial, about 65 per

Jan 1, 1944

By J. M. Hodge, M. A. Orehoski

It is now generally conceded that if a steel is to develop optimum physical properties in the conventionally quenched and tempered condition, the microstruc- ture after quenching should consist wholly of martensite; and that transformation of austenite to intermediate-temperature products during quenching will have a deleterious effect upon the physical properties, particularly the toughness, of the tempered material. This implies that, in order to obtain the optimum physical properties from a given steel, its "harden-ability " should be high enough to suppress all transformation except that to martensite under the heating and quenching conditions to which it will be subjected, and this premise is probably the most important reason for hardenability control. However, the criterion of hardenability that at present is most widely accepted and used is based on a microstructure of 50 per cent martensite. This criterion, which was suggested by Grossmann,' does have considerable justification. It may be readily measured by a fracture or etch test and, since it represents the point at which the hardness is changing most rapidly with variations in cooling rate, it may be determined empirically from a hardness-depth curve by determining the point of steepest slope (the inflection point). Furthermore, in plain carbon steels or in steels of low hardenability, the difference in hardenability expressed in

Jan 1, 1947

By Research Staff ? Verde Copper Mines

FLOTATION is now commonly practiced in alkaline ore pulps, yet little is known regarding the action of the alkaline solutions on the ore particles beyond the fact that films of oxidized material form. We wish to chronicle our discovery of the presence of soluble reducing agents in alkaline ore pulps of the United Verde, and present some data on lime consumption. During the grinding and flotation of a pyritic ore containing small amounts of ferrous sulfate and other soluble salts, an excess of lime was added to precipitate the salts, and filtered samples of the solution were titrated with standard permanganate solution. Even in pulps of high causticity an appreciable permanganate titration was always obtained, in spite of the fact that the solutions were shown to contain little iron. Investigation of the cause brought about the discovery of several previously unsuspected compounds in flotation pulps made from pyritic ore. Not only the reducing agents present had to be identified, but also the amount of dissolved oxygen, and a survey was finally made of the free oxygen content and reducing agents of the mill pulp in the concentrating mill at Clarkdale. A great many. compounds might form, caused by oxidation of pyrite or other metal sulfides or by reaction between a lime solution and pyrite. The most probable compounds considered were calcium sulfides, polysulfides, thiosulfates, and polythionates. Later it was discovered in the literature that in alkaline pulp polythionates do not exist and if introduced are decomposed into sulfites and thiosulfates.1 Any precipitated sulfur is changed by alkali into thiosulfate and polysulfide. Sulfites and sulfides react to form thiosulfate, so that in the end it is possible to have in an alkaline solution only thiosulfate and an excess either of sulfide or sulfite. Confirmatory tests were made and it was finally established that the alkaline mill pulps made from the United Verde ore contained

Jan 1, 1929

By C. W. Hamilton

In the production of crude petroleum for the year 1930 Venezuela again maintained its world rank of second only to the United States. During the latter months of the year Russia forged ahead of Venezuela in daily rate of production, and from the present outlook will probably rank second among the oil-producing countries of the world in 1931. It is now believed Venezuelan production has passed its peak. The producing fields of the Bolivar coastal district, along the east side of Lake Maracaibo, continue to be the principal source of supply. Such fields as Lagunillas, Mene Grande and La Pas were not produced to capacity throughout 1930. During the year, three new fields entered into commercial development: The Rio Tarra field in the District of Colon, State of Zulia; the El Mene de Salto field in the District of Acosta, State of Falcon and the Quiriquire field, District of Piar, State of Monagas. For 1930 the total crude production of Venezuela was approximately 137,424,000 bbl. as compared to 137,739,000 bbl. during 1929, or a decrease of 315,000 bbl. During the past year exports of crude from Venezuela amounted to 137,8.50,000 bbl. as against 130,044,000 bbl. exported during 1929. Crude oil in field storage decreased from 14,138,-000 bbl. at the beginning of 1930 to 9,600,000 bbl. as of Jan. 1, 1931— present crude stocks fill about one half the field tankage available. Drilling operations in the producing fields declined sharply but throughout the year there was maintained a satisfactory potential reserve in the shape of proven territory and closed-in producers. Of the 2555 wells which have been completed in Venezuela, 1571 wells were in production on Jan. 1, 1931. The status of these present producing wells may be classified as follows: flowing 652, pumping 170, gas-air lift 193 and closed-in 556. The ratio of closed-in wells to producing wells declined in 1930, while the number of wells produced by artificial means increased materially. In the Bolivar coastal fields there is now observed a marked decline in gas volume and well-head pressure. Lago Petroleum Corpn. and Venezuela Gulf Oil Co. each have under construction electric plants designed to generate power for pumping wells by electricity. The first units of these plants will be placed in conlmission in the early spring of 1931. Venezuela Oil Concessions, Ltd. has installed a number of stenrn-

Jan 1, 1931

By Charles F. Ramseyer

The manufacture of iron and steel is one of the largest of our industries; and in point of size of single plant and equipment certainly the biggest of all industries. By the general public it is generally considered a prime example both of the marvelous technical advances achieved by modern science and engineering in the design and operation of equipment and of the efficiency of big business in the coordination of men and materials. Actually the operation of its basic processes has not changed significantly in either theory or fundamental design of equipment in the past 75 years. Though many other process industries have been born and developed, and not seldom completely revolutionized, during this period, the primary processes of making iron and steel are still carried out along the lines laid down, and in the equipment originated so long ago, by Bessemer, Siemens and Martin, and subsequently expanded to practically the modern scale by Carnegie, Schwab and Captain Bill Jones in the eighteen eighties and nineties. The application of the principles underlying the continuous counter-current physical and chemical interaction of solids, liquids and gases, which have been so successfully used in the rapid evolution of our chemical process industries, has been very largely lacking in the steel industry. In the days of the last-named giants, especially Carnegie, the steel industry made great and rapid technical progress. Carnegie's ever driving idea (as later with Ford in the production of automobiles) was the finding of new and better ways of making cheaper steel. Carnegie himself was a steelman, and so long as he dominated the industry its technical progress was rapid; and he, like Ford, was vastly successful financially as well, since his costs were continually being driven lower than those of his competitors by his advances in steelmaking technique.

Jan 1, 1935

By T. L. Joseph

Charcoal was the predominant blast-furnace fuel until 1838, when it was found, by the operation of a 2-ton experimental furnace, that anthracite could also be used. This information was a stimulus to the iron industry, particularly in eastern Pennsylvania where anthracite was available at low cost. The production of anthracite pig iron increased steadily and, in 1855, its tonnage exceeded that of charcoal iron. Of the 680 furnaces in operation in 1874, the 226 using anthracite produced nearly one-half the total tonnage. In 1869, the production of coke furnaces exceeded that of charcoal furnaces and, in 1875, coke surpassed anthracite as a metallurgical fuel. In 1907, the output of anthracite pig dropped well below a million tons and its present significance is largely historical. In recent years, the production of coke has gone hand in hand with the production of pig iron and it has gradually attained the position it now occupies as a universal blast-furnace fuel. Charcoal, however, has great merit as a blast-furnace fuel chief1y because of its freedom from ash and sulfur. The harmful effect of the latter and the necessity of keeping the percentage of this element in pig iron at a minimum are well recognized. Other contaminating elements can be reduced to specified limits in the steel-making process, but the control of sulfur belongs essentially to the blast furnace. The purpose of this paper is to point out the distribution of this impurity in blast-furnace materials and to indicate how its presence alters the composition, quantity, and free-running or critical temperature of the slag, and the relation between these factors, fuel economy, and the cost of iron. Sulfur Distribution in MateRials Table 1 shows the distribution of sulfur in charcoal practice. Similar figures taken from coke practice are given in Table 2. These data were

Jan 1, 1925

By William S. Hannan, H. Rush Spedden

Flotation may be defined as a process whereby mineral particles are concentrated by selective adhesion to air-liquid interfaces. The process involves attachment of desired mineral particles to air bubbles, and removal of the mineralized air bubbles from the surface of the pulp as a mineral concentrate. Problem Although great strides have been made in understanding the principles of flotation, one part of the process which has not been adequately explained is the mechanism by which selected mineral particles become attached to air bubbles. A glance at the froth of an operating flotation cell demonstrates adequately that use of proper reagents and conditions mill result in such attachments; but how such attachment takes place is not definitely known. A better knowledge of this factor might lead to improved flotation practice either through altered machine design or the application of scientific innovations. Direct observation of the behavior of mineral particles and bubbles in an operating cell does not appear promising because of the complexity of the system. For this reason, conclusions concerning the problem must be deduced from theoretical considerations or from observation of simplified systems designed to reproduce conditions thought to exist in an operating cell. Present Theories Two mechanisms have been recognized as fundamental in particle-bubble attachment: gas precipitation and direct encounter. It is a simple matter to demonstrate in the laboratory that attachment can be brought about by either mechanism. As to the relative importance of the two in a particular flotation system, however, there is a divergence of views. Taggart1 states, Under exceptional circumstances sufficient force and time to effect attachment may conjoin in an ore pulp undergoing agitation, and a preformed bubble adhere to a collector-coated mineral particle, but the occurrence is rare. . . . Pulp-body froth flotation effects selection in the body of a conditioned pulp by causing gas bubbles to precipitate from solution in the liquid phase preferentially at the surfaces of collector-coated particles, and to cling to these particles, Gaudin2 states that, within the pulp body of an agitation machine, attachment of mineral particles to air bubbles occurs as a consequence of contact between the two. This theory has been supported by theoretical reasoning and much circumstantial evidence. Perhaps the most interesting bit of evidence in favor Of this theory js the difficulty in the flotation of fines. If attach-

Jan 1, 1949

By W. B. Humes

The use of high vacuum on a large industrial scale in the ferrosilicon process for the production of magnesium marks the coming of age of an important new metallurgical technique. The economical production of reactive metals, such as magnesium, which combine with all the well-known furnace atmospheres, has until recently been successfully carried out only by electrolytic methods. It is now apparent that, through the use of high vacuum, the distillation or sublimation of many metals can be done industrially at much lower temperatures, and hence in much simpler equipment, than heretofore has been thought possible. At the beginning of the present emergency, when the ferrosilicon process of producing magnesium was brought to the fore, little was generally known about vacuum engineering, practices, and techniques. In a comparatively short time, the available equipment has been adapted, new equipment designed and built, and a fund of know-how evolved to make possible the production of thousands of pounds of magnesium per day at pressures less than 1/ r0,000 of an atmosphere. Pilot-plant operations have been consistently maintained at pressures even as low 2s one micron (0.001 mm.). These low pressures, which previously were regarded as prohibitively costly or impossible to attain, have been demonstrated as economically feasible on an industrial scale. Necessity for Vacuum The main function of vacuum in the ferrosilicon process, and hence in most vacuum smelting processes, is to lower the temperature at which the metal may be distilled or sublimed from the reduction mixture. A secondary function is to protect the distilled metal from attack by the furnace atmosphere and to permit the formation of a dense condensate. In the ferrosilicon process, magnesium is formed by the reaction between dolomite and ferrosilicon: 2(Mg0-Ca0) -\- HFeSU / t=> aMg + MFe + (CaO)2-SiO2 The metal is distilled from the pelleted charge at a free air pressure of about 0.100 mm. of mercury (100 microns). This low pressure is not needed for the reaction, but rather serves to protect the metal vapor from the oxygen or nitrogen of the atmosphere and permits the formation of a condensate free of pyrophoric material. The reaction proceeds at air pressures as high as several millimeters of mercury, and evidence has been offered to show that the actual equilibrium pressure of magnesium at operating temperatures of 2I50°F. is somewhat higher. Experimentation indicates that the yield begins to decrease at pressures above 500 microns. While no real operating data are yet available on the relationship between

Jan 1, 1944

By R. I. Jaffee, H. R. Ogden, D. J. Maykuth, W. L. Finlay

Titanium with up to 7.5 pct Al forms single-phase a alloys that are work hardening, not heat treatable, and ductile as welded. The high aluminum Y phase alloys are not usefully ductile, despite their low hardness, but they have excellent oxidation resistance and hot hardness. LITTLE has been published on the effect of aluminum on the mechanical properties of titanium, despite the fact that two of the first four commercial alloys released by titanium alloy producers contained aluminum as an important alloying ingredient. These were both a-ß type alloys, one containing 4 pct A1 and 4 pct Mn and the other containing 3 pct A1 and 5 pct Cr. However, neither of these alloys reflects the true alloying nature of aluminum, since each contains important amounts of the ß-stabilizing addition, manganese or chromium. In a previous publication on the constitution of Ti-A1 alloys,' the authors showed that aluminum had a high solubility in a titanium and was strongly a stabilizing in nature. About 25 wt pct A1 is soluble in a titanium at room temperature. With as little as 5 pct added aluminum, the a transus temperature is increased from 882" to 970°C, and the correspond- ing ß transus to 995°C. The first intermediate phase in the Ti-A1 system is the ordered face-centered tetragonal TiAl phase, which extends from 34 to 46 wt pct Al. The present paper presents hardness data over the entire titanium-rich region of the system, through the TiAl phase, and mechanical property data on the alloy range capable of being fabricated. Methods of Investigation The materials used and general preparation of alloys, as well as experimental techniques used in the investigation of Ti-A1 alloys, have been adequately described.' Briefly, the preparation consisted of arc-melting the desired amount of high purity aluminum (99.99 pct purity) and iodide titanium (maximum hardness 100 Vickers, as deposited) together on a water-cooled copper hearth under a partial pressure of argon. The resulting button ingot was of such form that it could be fabricated without further treatment. All work was done using ingots weighing 10 to 15 g, which were hot-rolled to strip form whenever possible. Tensile samples were 3.25 in. long, 0.5 in. wide, and 0.040 in. thick, with a reduced section 1.25 in. long by 0.250 in. wide. The gage length used was 1 in. Electrical strain gages mounted on the

Jan 1, 1954

By Clinton M. Young

The experiments herein described were carried on in 1908-9 by- the State Geological Survey of Kansas. Some months before taking up work on black powder the Survey had resumed work on an interrupted investigation of explosions in coalmines, a subject which is engaging the attention of numerous investigators. An unusual number of serious disasters has directed to the subject a study which discloses the disquieting fact that, in the United States, the ratio of lives lost per ton of coal mined has been 011 the increase. Methods of coal-mining have changed to some extent with the great increase of output, attained in comparatively recent years. These changes involve the working of very extensive mines, with increased difficulty of ventilation, increased accumulation of coal-dust, and a very great increase in the amount of explosive used. This last point assumes truly startling proportions when it is carefully observed. In the fields of the Middle West it is not now uncommon for a miner to use six kegs (150 lb.) of black powder in a " pay" of two weeks, while within the memory of men still active, one keg (25 Ib.) would last two men for a " pay." So great has the use of explosives become in some fields that the skilled coal-miner is hard to find, and the coal is not mined, but blasted. A preliminary study of the subject of explosions in coalmines has led to the belief that the use of large quantities of explosives, in some cases by slightly-trained men, had riot been

Jan 1, 1911

By Jay A. Carpenter

This paper deals with only one step in the treatment of ore at the West End mill; not because the other steps are repetitions of practice in other mills, but because in this particular step there is in use the Trent agitator: This device, although it has apparently failed in many mills, is here giving excellent service and has proved to be well adapted for making a thorough replacement of pregnant solution with a minimum amount of barren solution. The strong and weak points of this agitator, its present simple construction, and its use as a thickener for agitator or battery pulp are features of interest; but perhaps the point of greatest interest to the metallurgist in this day of continuous decantation is its use in a series of tanks for slime treatment by the replacement method. The agitating department of the West End mill consists of six redwood tanks, 24 ft. in diameter, 18 ft. high, each equipped with a Trent agitator, a centrifugal pump, and a motor. The pulp is transferred by a pump from the top of a flat-bottomed tank to a set of arms and nozzles in the bottom of the tank, at just sufficient pressure to cause the arms to revolve. The streams from the many nozzles keep the bottom of the tank clean, and these streams, coupled with the effect of the revolving mechanism and the ascending current, keep the pulp in constant motion and of constant gravity. These agitating tanks hold 90 tons of dry slime and 202 tons of solution with a 1.24 pulp, our ore having a specific gravity of 2.7. This capacity is about 10 per cent. in excess of the standard 15 by 45 ft. Pachuca tank. The tanks are connected in one series for continuous agitation, the pulp for each agitator being drawn by its pump through a branch suction from near the top of the preceding tank and delivered to the bottom of the tank by the agitator arms along with the regular pulp of that agitator. This method works automatically, since the flow through the branch suction varies directly with the difference in head of the two tanks. The chance for new pulp to pass out quickly is, therefore, much less than in many other systems of continuous agitation, since the new

Jan 1, 1916

By G. R. Lehman

The Inspiration Consolidated Copper Co. had an orebody at Miami, Ariz., of close to 100,000,000 tons of low-grade copper ore, and the method of mining this ore most profitably was of great importance. The selection of a method was practically limited to a "top-slicing," a "shrinkage-stope" or a "caving" method. The "top-slicing" method would give a high extraction of the developed ore, at a high mining cost, and the "shrinkage-stope" or "caving" methods a lower extraction of the developed ore, at a lower mining cost. Ore-Drawing Tests To decide on the method to be used it was necessary to know about what extraction of the ore could be obtained by the "shrinkage-stope" or " caving " methods. As no definite information regarding the,question was available at the time, C. E. Mills, the general manager, thought that some information could be obtained by experimenting in drawing ore, covered with capping, from an experimental box. Some work had already been done along these lines by W. C. Browning for the Inspiration Copper Co. and by myself for the Live Oak Development Co. The idea was to represent as nearly as possible, in the experimental box, the conditions within an area of caved stopes of caved ore all ready for drawing. That is, the area was supposed to represent a semibroken mass with the capping above it in the same condition and ready to follow the ore downward as it was drawn out of the chutes under the ore. To represent the above condition, in the experimental box, crushed ore from the mine was placed in it to a given height, and red barren capping from the mine was placed on top of the ore. The Experimental Box The experimental box shown in Fig. 1 was made of wood and glass. The glass was used for the sides so that the drawing action of the outside row of chutes could be seen and noted, the latter being cut in the center by the glass sides. The length of the box was 30 in., width 20 in. and the

Jan 1, 1917