Search Documents

ALTHOUGH the open-hearth charge contributes CO, C02, H2, and water vapor to the combustion gases and absorbs oxygen from them, in the main the thermal effects in the melting charge and molten bath can be considered independently of those in fuel combustion; the latter then is regarded simply as the source of the net heat required to finish a heat of steel. First of all, it should be remembered that a large percentage of the heat supplied to the bath is furnished by oxidation of the various elements in the charge itself. If this charge consisted of 80 to 100 per cent of hot metal and the oxidation were accomplished by blowing in air or oxygen, as in the bessemer converter, the net heat absorption would be negative; that is, the bath would contribute part of the heat required to keep the melting chamber hot, in addition to that contained in the finished steel and slag. - In actual open-hearth practices, probably the nearest approach to this is in the duplex furnace, charged with bessemer-blown metal and some hot metal, where very little heat is required to complete the refining and nearly all the heat energy from fuel combustion is used to keep the roof and walls of the melting chamber up to around 2900 to 3000 F (1600 to 1650 C), so that the bath will not cool off during the refining. The other extreme is with all-cold charges containing around 80 per cent steel scrap and 20 per cent cast iron or cold pig iron, in which case a very large proportion of the heat in the bath at tap is supplied from the fuel combustion. THERMAL EFFECTS IN MELTING In a typical heat, the fuel furnishes about four million British thermal units per ton of steel produced. The heat required for the metallurgical processes is not easily defined in useful manner but it ranges downward from about one million Btu, depending not only on the charge but on the manner of calculation. In any event, this requirement appears small in comparison with the

Jan 1, 1951

By B. Silliman

The regions of New Mexico referred to are in Socorro, Grant, and Dona Ana counties, and a portion of Lincoln County, embracing in the aggregate a very large area, of most of which our knowledge is as yet very fragmentary and superficial. It is only very recently that large portions of this region have been accessible. It has been full of danger from hostile bands of wandering Apaches, whose murderous raids have slain many adventurous miners and seriously prevented developments. But this evil has now been largely abated, and in many of the mining camp of this region there is no longer any danger from this cause. SOCORRO MINES. About three and a half miles back of the old Mexican town of Socorro, on the Rio Grande, chief town of the County of Socorro, are two or more large veins of heavy spar, cutting across the fat* of Socorro Mountain in a northeast and southwest direction, and dip ping at an angle of about forty degrees into the body of the mountain. These veins are in rhyolite, and, so far as could be seen in openings on the Torrence Mine, which I examined, are without any clay parting or selvage. The average thickness of the Torrence rein may be about five feet, the thickness varying from pne or two feet to thirteen feet. Upon the cleavage planes of the heavy spar occurs, in visible patches, of a waxy Iustre and gray color, silver chloride, which gives value to the vein, from a few ounces up to one hundred and twenty ounces to the ton, averaging about forty ounces, as I

Jan 1, 1882

By M. O. Holowaty, C. M. Squarcy

1750 to 1850: The scene shifts westward across the Alleghenys to the young town of Pittsburgh; charcoal gives way to mineral coal as furnaces grow larger and the blast is heated; above all, Pennsylvania iron is adding strength to the new Nation and building an empire in the West. TWO names are inseparably associated with the Pittsburgh iron industry-those of George Anschutz and John Hayden. The iron ore deposits of southeastern Pennsylvania were found and developed early in the 18th century, and several forges and furnaces were built and operated. It was only after the revolution that the iron men crossed the Susquehanna River, built furnaces in the neighborhood of ore deposits of Franklin County, then along the Juniata River and its valley. Juniata Iron found a ready market in the Pittsburgh area. However, difficulty in transporting it across the Allegheny Mountains induced iron mas¬ters to seek ore and plant locations in the Pittsburgh district. One of the first to reach this area was George Anschutz, who migrated to America in 1789 at the age of 36, reaching Pittsburgh in the fall of 1790. Anschutz immediately set out to organize an iron company in Pittsburgh, and was able to interest some residents in his project. After being informed of an iron ore deposit located only three miles out of town (on the site of the present 26th St. and the Allegheny River) he decided to build there his blast furnace and foundry plant. Total cost of the installation was $300. When the furnace was put in operation, Anschutz, now known as Red George, found that the ore deposit was only an insignificant one and would last no more than a few weeks. A new deposit was found on Roaring Run, in the southeastern corner of Armstrong County. Anschutz transported some of this ore to the mouth of Two Mile Run, where it was loaded on horse wagons and transported to the furnace. In this way, he operated off and on for several months, until the furnace was blown out in 1794. After working for a year as plant manager for John Probst at Langhorntown, he built the Hunting-

Jan 1, 1961

Jan 1, 1944

By T. W. Guy

IN approaching the problems of sampling coal, a brief statement of certain facts that are more or less taken for granted may he helpful: 1. The coal-mine operator needs reliable data as to the physical and chemical characteristics of his coal in order to plan and control intelligently its mining, preparation, and marketing. The consumer needs such data in order to select the equipment and the coal best suited to meet his requirements, to check the quality of fuel delivered, and the efficiency of its use. Various government control agencies require such data as a basis for classifications and establishment of limits, for use in carrying out the requirements of federal, state or municipal laws. 2. All such data must be obtained by analyses, measurements, or tests made on samples, which are taken to represent the coal tested. It is now becoming generally recognized that, in accordance with statistical laws, test results from samples are not expected to represent the exact qualities of the lot or lots from which they are taken, except within statistical, or "expected" limits. Such limits are definitely specified by some present standards of the American Society for Testing Materials and the British Standards Institution. 3. Samples that give ash within satisfactory limits are usually assumed to be sufficiently accurate for other analyses, except under special conditions such as meeting close specifications for coals showing wide variability in sulphur, fusibility of ash, or other quality. 4: In. modern coal sampling the increment is recognized as the basis for taking samples. For a given accuracy the number and weight of increments specified are increased with: (a) the expected ash, and (b) the top size designation of the lot to be sampled. 5. It is extremely important that every sampler recognize that: the specified number and weight of increments are minimums, and that. the precautions to be used in order to take them properly are also minimums; that in the reduction of the gross sample the sizes specified for the coal after each stage of the crushing are maximum; that the quantities specified to be taken after each crushing stage are minimum; that any short cuts or failures to meet the requirements specified will reduce the statistical accuracy of the results, although it is possible that one or two checks on a few results may seem to show otherwise.

Jan 1, 1943

By Raymond B. Ladoo

NONMETALLIC minerals (excluding fuels) arid their primary products produced annual in the United States have a value in excess of one billion dollars, or more than that of the metals, yet the lack of expert knowledge of some of the fundamental technical and economic aspects of this most important and complicated business is astonishing. This paper will deal with the economics of this non- metallic mineral field-the business of making money from producing these minerals. The incentive behind all business activity in a capitalistic economy is to make money-to plan so that each dollar invested in property, plant, equipment, services, and so on will return more than a dollar plus simple interest. Of course, business has social, civic, and national duties and responsibilities, but the fulfillment of these is largely dependent upon financial success.

Jan 1, 1939

By H. D. Dahl, P. C. Thakur

This paper presents an analysis of a new tool for improved productivity in coal mining: the horizontal drilling system developed by Conoco/Consol. The analysis includes a brief description of the system; discussion of the three categories of advance exploration application of horizontal boreholes; and a survey of other special mining methods planned around long horizontal boreholes.

Jan 1, 1983

By R. J. Blackwell

By John T. Eash

DURING the course of the war the supply of tin in this country has steadily decreased and a continued effort has been made since the beginning of the emergency to use alloys that are either tin free or contain appreciably lower quantities of it. Even with the use of emergency materials, the tin supply has become particularly acute, and it is estimated that after recovery of the far eastern mines probably one to two years will be required before our normal annual supply is attained. One of the major tin-consuming fields is the bronze industry. Recommendations were made several years ago by the War Production Board toward the use of bronzes of lower tin content and manganese bronze and yellow brass for the customarily used tin-bronze alloys. The substitution of 88-5-5-2 copper-nickel-tin-zinc for composition G received considerable attention before the war, and consequently this alloy and modifications of it have been adopted for some current structural and pressure castings requiring high mechanical properties. Another of the commonly used bronzes is the 10 per cent tin, 10 per cent lead copper alloy for heavy-duty bearings. It has been known for some time that about 2.5 per cent nickel could be substituted for an equal amount of tin with retention of equivalent casting and tensile properties; however, it was desirable that a still greater conservation of tin be made. Consequently the present paper deals with the development of an alloy of low tin content that could be used for bearings. SELECTION OF COMPOSITION While the final criterion of the suitability of an alloy for a bearing must 0f course be determined by practical applications where all the ramifications of service conditions are encountered, certain short cuts in the initial selection of compositions are necessary to avoid an extensive and time-consuming investigation. The present program has been to match certain metallurgical properties of the 80-10-10 bronze that have been shown by previous investigations to be related to good bearing qualities. Such properties as microstructure, hardness, compressive yield strength, ductility, and castability have been considered, and certain simple wear tests have been made. Of the readily assessed characteristics desired in a good bearing alloy, one can be certain that a uniform distribution of lead is required in a leaded bronze. It has generally been found that segregation of lead is one of the chief difficulties with this type of material. Tin has a powerful effect on lead distribution, and with 10 per cent present produces a random distribution of chunky particles, such as are shown in Fig. I. In addition, the tin bronze contains the hard alpha + delta eutectoid constituent distributed through-

Jan 1, 1945

By J. W. Hickman

INTRODUCTION MOST of the electron diffraction studies of oxide films which form on metals and alloys have been carried out by oxidizing the specimens in an auxiliary furnace, cooling down to room temperature and then inserting the sample in the camera and taking a diffraction photograph. Prior to the investigations at the Westinghouse Research Laboratories, no systematic study of the oxidation of any metal or alloy had been made over a wide temperature range with photographs taken at elevated temperatures except the investigation of iron by Jackson and Quarrell.1 In order to interpret the electron diffraction patterns of the oxides which may form on alloys, it seemed advisable to make a comprehensive study of the oxidation of the purest metals available in the bulk form. Thus far studies have been completed on iron,2 cobalt,2 nickel,2 chromium ,2 Copper2, tungsten,3 molybdenum,3 beryllium ,4 uranium,4 thorium4 titanium5 and zirconium5 while investigations are in progress on tantalum and columbium, The next step in the study is concerned with the investigation of the oxides which form on binary alloys. Some of the alloys consist of a single, phase while others contain more than one phase. The identification of the oxides on the surface of a binary alloy may be more difficult than on the metals since oxides containing both metals as well as those of each metal separately may form. Furthermore, it is possible that solid solutions of the various oxides may occur. In these cases the electron diffraction method may not be able to identify the oxidation products unequivocally, Examples of solid solutions which may present difficulties are MoO2 and W02, Fe3O4 and FeO-Cr2O3 since the diffraction patterns are so similar. Since electron diffraction can determine only the structure of the oxide, the chemical composition must be inferred from the diffraction data based upon X ray diffraction investigations of specimens of known composition. It is possible in some cases to decide whether a given solid phase reaction can occur on the surface of an alloy by a study of available thermodynamic data. Table I lists the equations for the formation of most of the oxides from the elements together with values of log10 KR for the several temperatures. [OF°R = -RT In KR 0 and-~75T = logi°KR] [?F°R] and KR are the free energy and equilibrium constant of the reaction. Calculations may be made using the values given in Table I to determine whether a given solid phase reaction is possible thermodynamically. For example, a solid phase reaction should occur between aluminum and chromium' oxide to form

Jan 1, 1948

By Jack A. Caldwell

Jan 1, 1985

By R. J. Wasilewski

OBSERVATIONS have been made that the substitution of antimony for bismuth in Bi2Te3 leads to anomalies in some of the electrical and magnetic properties of the Bi2Te3-5S2TeS alloy system at the composition ratios 2 Bi2Te3 : 1 Sb2Tes and 1 Bi2Te3 : 2 Sb2Te3. Airapetiants and Efimova1 have reported the peaking of the nondegenerate hole mobilities, at these compositions for sintered materials and ascribe the peaking to the formation of ordered alloys. From a study of these materials produced by the Bridgeman

Jan 1, 1962

By Kenneth N. Weaver

Portland cement can be made from relatively abundant industrial minerals and rocks, and this may explain why cement producers placed little emphasis on geology during the early days of the industry. After World War II, however, the industry began to recognize the need for geological exploration, and some of the larger companies began to build a permanent geological staff. This development had its roots in the following factors: Rapid expansion of the industry; closing of many cement plants due to inadequate raw materials; necessity for upgrading the quality of portland cement; and the increasingly large capital investment required to build new cement plants, which in turn, required a higher degree of accuracy in reserve calculations. Whereas the geologist's function during the active expansion of capacity was primarily in exploration, one of his major functions today is the development of existing reserves.

Jan 1, 1965

By Kenneth A. Grace

Jan 1, 1985

By Ernest G. Enck

Expanding markets and technological investigations now in progress for commercial production of titanium metal and alloys, as well as expanding uses for the oxide, have resulted in greater production, increased prices, and accelerated search for additional commercial occurrences of titanium minerals. For more than 50 years rutile has been used in moderate quantities in ceramics, in the production of ferrotitanium, as well as nonferrous titanium alloys. During the early 1930's, use of pure titanium dioxide was introduced as an ingredient of coatings for electric welding rods. For technical and economic reasons rutile was soon found to be as good or better for mild steel welding rods, and this use continues to account for a good share of the rutile sales in the U. S.

Aug 1, 1956

Jan 1, 1913

DR. E. E. SOUTHARD,* Boston, Mass.-As Director of a Psychopathic Hospital, I am a sort of "voice in the wilderness" speaking to mining engineers. I suppose that I am here because Major Gilbreth had prevailed upon me to speak on a kindred topic before the mechanical engineers at the annual meeting of their Institute. You might wonder why a psychopathic hospital, a state institution for the first care of mental cases and especially for incipient, acute and curable cases, should have any part or lot in the industrial problem. We have obvious contacts in our institution with the retarded and exceptional children of the schools, with the defective and non-defective

Jan 4, 1918

By Charles Meyer

The year 1955 was a busy one for mining geologists, for the expanding world-wide business activity kept the demand for mining products generally high, stimulating operators to develop local ore reserves and to expand their efforts to find new deposits. The uranium rush was still on, although probably past its maximum rate of climb. Prospecting was also stimulated by the increasing demand for rare metals, and this created new and fascinating targets for exploration. On the whole, it was a boom year when the prospector's chronic optimism found few repressions.

Feb 1, 1956

By Ralbern H. Murray

The decline in deliverability of conventional natural gas supplies and the general energy crisis have resulted in national programs directed toward the commercialization of energy conversion technologies. Foremost among these efforts is the gasification of coal. Coal reserves represent our most abundant fossil fuel resource. Its utilization is hampered both by its form value and its pollution qualities. Coal gasification is commercially feasible today and projects requiring hundreds of millions of dollars and years of construction time are underway. This paper provides a perspective for the scope, time, and cost of these venture projects. Resource requirements, plant products, and coal gasification processes are discussed. Emphasis is placed on the effects of coal feedstock and prices on plant economics.

Jan 1, 1976

By Walter Crafts

STRUCTURAL steels containing chromium have become widely used in the last 20 years. In the earlier part of this period the major applications were in chromium-molybdenum aircraft tubing and similar special high-strength steels. During the past 10 years there has been a notable expansion in the use of chromium-bearing steel for structural purposes when welding was utilized for fabrication. The chromium-bearing steels introduced by Saklatwalla1 (chromium-copper), Kinzel2 (chromium-manganese-silicon), and Schultz3 (chromium-copper) are being extensively used at the present time.

Jan 1, 1939