Search Documents

By L. B. Ticknor, M. B. Bever

An isothermal calorimeter suitable for measurements of heats of solution in liquid tin as solvent is described. Measurements of the heats of solution of gold, silver, copper, and a gold-silver alloy are reported. The heat of formation of this gold-silver alloy is also reported. HEATS of solution in liquids can be determined directly, but few such data have been published for metals as solvents. Knowledge of heats of solution is desirable because it contributes to the general understanding of energy relations in metallic solutions. Thermochemical measurements of this type also furnish answers to specific problems: For example, from the heats of solution of an alloy and of a mixture of its constituent elements in a given solvent, the heat of formation of the alloy may be found. Similarly, differences in the energy content of samples of the same metal in two different states, such as the annealed and cold worked states, may be determined. In the work reported here, gold, silver, and an alloy of gold and silver were dissolved in liquid tin at 240°C and gold, silver, and copper were dissolved in tin at 300 °C. The experiments yielded the heats of solution of these metals in tin. The heat of formation of the gold-silver alloy was also determined. The same calorimetric method is being used to measure the energy stored in metals during cold working and preliminary results have been published.' Equipment and Experimental Procedure The isothermal calorimeter used in this work, Fig. 1, consisted of a Dewar flask completely immersed in a constant-temperature salt bath. A long neck provided space for thermocouple leads and a stirrer shaft and permitted the injection of solute samples. The metal bath in the calorimeter flask was stirred at about 100 rpm by a small glass impeller driven by a constant-speed motor. The shaft of the stirrer passed through a Wilson vacuum seal.2 All measurements were made under vacuum in order to eliminate temperature disturbances resulting from gas convection and to prevent the oxidation of tin. The calorimeter flask was joined by an all-glass connecting line to a gas-control system which made possible the use of a protective atmosphere of deoxidized and dried hydrogen. At the operating temperature of the calorimeter tin oxide was not reduced by hydrogen, presumably because the reaction rate was too slow. Part of the closed system was a removable side tube through which the solute sample could be introduced and in which it was held at a temperature of 0°C prior to injection into the metal bath. The salt bath containing a mixture of sodium, lithium, and potassium nitrates was similar to that described by Beattie3 and was equipped with a stir-

Jan 1, 1953

By R. S. Christie

Reservoir pressure is the pressure at which a fluid is held in a state of equilibrium in a porous stratum. This pressure may be a result of the genesis of oil or gas and its subsequent migration into and through an adjacent porous stratum, or of hydraulic head. Reservoir pressure is an indication of the potential energy contained in the reservoir, and when it is known the engineer is in a position to use it to advantage in recovering and lifting the oil. It is important to know the pressures in any type of reservoir, but this knowledge is probably of greater value in a limestone reservoir, as at Hobbs, where producing rates or conditions may be more sensitive to changes in pressures. The Hobbs field is in east central Lea County, New Mexico. The discovery well was completed by the Midwest Refining C I. in 1928, but intensive development did not begin until after the completion by the Humble Oil and Refining Co. of No. 1-A Bowers in February, 1930. There are 143 producing wells on approximately 5500 acres. The field has not been defined to the northwest, but a projection of structural contours indicates that the productive area ultimately may cover 7500 acres. The producing horizon is the White or Crystalline lime of Permian age. The top of the lime is found at an average depth of 4000 ft. and the wells penetrate it an average distance of 200 ft. The main pay zone is an oolitic stratum about 25 ft. below the top, and varies from 2 to 15 ft. in thickness. Other porous or cavernous strata are found lower in the lime but have little saturation. The initial production varied from 100 to 25,000 bbl. per day, depending perhaps to some extent on the structural location but chiefly on the porosity of the pay. The initial gas-oil ratio varied from 325 to 16,000 cu. ft. per barrel. In wells where the top of the White lime was found below 350 ft. below sea level (Fig. 1)) the gas-oil ratio was usually less than 1500 cu. ft. per barrel, while in wells higher than 350 ft. below sea level, the ratio was usually above 2000 cu. ft. per barrel. The water table has been determined at about 620 ft. below sea level, by three wells on the west side of the field. With few exceptions, the wells have been completed with 7-in. casing cemented

Jan 1, 1932

TO THE BOARD OF DIRECTORS AND THE MEMBERS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS Gentlemen -It is pleasant to be able to report that the year just closed has been a prosperous and successful one for the Institute As is shown by the reports of the Treasurer and the Finance Committee, the business affairs of this organization are in excellent condition With property valued at more than three-quarters of a million dollars, and with con¬siderable sums in various funds and endowments, it is possible to spend on each member of whatever class $22 65 each year, more than the maxi¬mum amount of dues received from any one, and substantially twice the average amount, $10.94, received from all To do this has required close management and a strict regard for our limitations In 1926, when the Budget was made up, the estimated expenditures for the work which it was felt the Institute must do exceeded the estimated receipts by some $14,000. At the close of the year, despite a` number of unexpected decreases in receipts, it had proved possible to accomplish substantially all the work laid out and close the books with the usual transfer of initia¬tion fees to the General Reserve, and still only reduce the cash balance $2,074 54. This was made possible by the hearty and loyal cooperation of the whole staff of employees and the extremely large amount of gratui¬tous service rendered by the officers, the members of the Divisions and technical Committees, and the membership generally Even so it was impossible, because of limitations of funds, to undertake many things it is highly desirable for the Institute to do, and it was necessary to refuse the publication of important papers and committee studies, because of the lack of funds.

Jan 1, 1923

By A. E. Harnsberger

I is obvious that details such as the physical and chemical properties and methods of heat-treating of the materials mentioned must be omitted in a paper on the subject of materials used in oil-refinery pumps1. Only sufficient identification is given to enable the reader to find additional information from already published data. Also, the subject covers many operating conditions, but only the most important services can be discussed here. To the oil refiner, the pumping equipment is of vital interest. Practically every refinery operation, from the charging of crude oil to a distillation unit to the shipping of refined products, involves some form of pumping machinery. Intermediate refining stages involve a great variety of pumping machinery to carry out successfully the aims of the refinery technologist. Temperatures at which oils are handled vary from — 50" F. to 900" F. Pressure may vary from subatmospheric to 2000 1b. per sq. inch. The selection of the proper materials involves a careful consideration of the conditions under which the particular pump must operate. The four most important considerations are temperature, pressure, corrosion, and abrasion or wear. Consideration of temperature may be divided into three parts: (1) extremely low temperatures of the order of —50" F.; (2) temperatures at atmospheric or slightly above; (3) temperatures from 200" to 900" F. Pressures fall into two groups: (1) pressures reached by ordinary trade pumps of the order of 200 lb. per sq. in., (2) extreme pressure conditions involving pressures as high as 2000 lb. Noncorrosive and corrosive oils can be treated differently. Under the latter falls corrosion in the presence of water, which will occur up to 250" F. The second type of corrosion occurs in high-temperature pumping equipment, with temperatures from 450" to 900" F., largely caused by sulfur compounds. There are also other corrosive conditions met with in refinery operations, particularly in the handling of acids, acid sludges and other specialized processes. These problems, although difficult to

Jan 1, 1935

By F. Cadena

HIWASSEE Dam, now under construction by the Tennessee Valley Authority on the Hiwassee River, a tributary of the Tennessee River, will require aggregate for approximately 800,000 cu. yd. of concrete. Near the damsite deposits of natural sand or gravel are not available and graywacke, a rock that is found in abundance, suggested itself as a likely source of manufactured aggregate. Graywacke is a metamorphosed sandstone composed principally of a mixture of quartz (65 per cent), mica (25 per cent), and feldspar (10 per cent). Other minerals are present in negligible amounts. The rock varies in different parts of the quarry from very fine to a coarse grain containing particles of about 1/4 in. maximum size, although the bulk of the deposit is medium grain. Extensive tests showed that graywacke would be suitable as a source of both coarse and fine aggregates. The aggregate plant available for use at Hiwassee Dam consisted of the coarse-aggregate and sand plant used on the Norris project. The coarse-aggregate plant had also been used at Chickamauga Dam. Although most of this plant equipment is now in use at Hiwassee, the present flowsheet is not only different from that at Norris and Chickamauga but is also unique as compared to the flowsheet of the average crushed-stone aggregate plant. It is hoped that this paper will show the importance of proper arrangement of equipment if the optimum in flexibility and capacity is to be attained. FLOWSHEET Rock is loaded by 3-yd. electric shovels into 12-yd. dump trucks, which carry the rock to the primary crusher, a 42-in. Superior McCully gyratory unit set at 4 ¾ in. (Fig. 1). The primary crusher discharges directly onto a 42-in. inclined belt conveyor, which carries the product to a surge storage pile with a maximum live storage capacity of approximately 3000 tons. A concrete tunnel under this storage pile houses the feed end of a 36-in. belt conveyor (conveyor B) fed by a 36 by 66-in.

Jan 1, 1939

By Stephen E. Merritt, John W. Straton, T. Carl Shelton

Surveying and mapping are used to locate and visually portray objects, lines, or areas in relation to a reference point or line. The actual making of the measurements to locate the objects and points falls under surveying while mapping is concerned with putting the survey information into a graphical form. Generally, the type or class of proposed survey depends on the precision required. Some surveys may need only approximate measurements which can be obtained by simply pacing or by using an ordinary measuring tape; others may require much accuracy, thus calling for the use of an engineer's transit or theodolite along with a graduated steel tape for horizontal measurements, or a level and a graduated rod for measuring vertical distances. Mapping is likewise dependent on accuracy requirements. For example, a general layout showing the relative position of surface facilities may not call for a large scale of dimension or great precision whereas for detailed work, a large scale plus care in plotting points and drawing lines and curves are important factors. SURVEYING METHODS There are many kinds or types of surveying methods. Some examples include : land surveying for determining boundaries of land areas; route surveying for locating roads, highways, right-of-way, and haulways; city surveying for laying out lots, streets, and alleys; and mining surveying for projecting mine openings and locating mining operations. See Fig. 1. There are other types of surveying than those named, but in general, the type of method to be used will depend on the purpose for which the survey is to be made.

Jan 1, 1981

By Alexander Squire

ONE of the principal factors that have contributed to the hesitancy of design engineers to use metal-powder parts is the difficulty experienced in the determination of the mechanical properties of compacted components. Because standard test: methods cannot usually be applied in the inspection of such parts, and because adequate special test methods have not been developed, it has been considered desirable to investigate the methods that are applicable. These may then be included in specifications for metal-powder materials' and components in order that the design engineer may be assured that the subject parts possess the desired mechanical properties for satisfactory performance. It is known that direct relationships exist between usually nonmeasurable properties as tensile strength and elongation and shear strength and the angle through which compacts may be plastically deformed before fracturing. These correlations are valuable in the inspection of specific parts, but it is necessary to set up standards before they may be satisfactorily employed. Apart from the use of correlations, the number and character of the inspection methods that are applicable to almost all powder parts is limited to three-chemical analysis, density, and hardness. The last of these may or may' not be a pertinent characteristic, since the indentation hardness of many powdered-metal materials is so low as to have little significance. It is, however, occasionally desirable to use hardness measurements as an indication of the uniformity of the structure of pieces of a given type. Chemical analysis reveals very little about the physical properties of metal-powder compacts, since the unpressed powder is usually of a composition almost identical with that of the finished pieces. Density determinations are simple, to perform and have the advantage of being nondestructive in character. If the dimensions of a machine part are known (and usually they are), the average density may be determined by weighing a given number of pieces and dividing by the calculated volume of the parts. More accurate measurements may be made by the water-displacement method. , It. is recognized that mechanical properties of metal-powder materials are related to their density, but usually these relations are determined for only one type of powder, processed under a given set of conditions. Comparisons of the properties of compacts formed from different types of powders are made on the basis of compacting... pressures instead of density, and for. this reason the results obtained by using powders of different types appear widely variant.

Jan 1, 1947

By George W. Maynard

In the death of Sir William Siemens, the Institute loses its most distinguished honorary member, one who, without exaggeration, may be ranked among the greatest Men of the century. In justification of this claim, I quote in part the words of two other men eminent in the walks of science. Professor Huxley, addressing the Royal Society, spoke of Siemens as "a marked example of vast energy, large scientific acquirements, and intellectual power of a high order," and as one " who had no superior in fertility and ingenuity of invention, while hardly any living man so thoroughly combined an extensive knowledge of scientific principles with the power of applying then] in a commercially successful manner. The value of his numerous inventions must be measured, not merely by the extent to which they have increased the wealth and convenience of mankind, but by the favorable reaction on the progress of pure science which they, like all such inventions, have exerted, and will continually exert." Dr. Wedding, in his address before the Verein zur Befarderung des Gewerbefleisses in Preussm, speaks of Siemens as being "so fortunate as to combine German erudition with British activity in such a manner that both nations, Gertnan as well as English, were equally proud of him; and, now that his rich life is ended, regret is expressed on both shores of the North Sea, first by the Germans that his entire life had not been spent in Germany, and his powers dedicated to Germany, and by the English that he was not born a Briton." Germany may well be proud of being the birth-place, not only of such a man, but of such a family; for where in history shall we find in a single family such a wide range of knowledge so successfully applied to the arts? The least distinguished name in the following list has added to the world's knowledge enough to satisfy the desire for fame of any ordinary man. This constellation is made up of:

Jan 1, 1884

By A. B. Kinzel, Walter Crafts

A PRevioUs study1 of the relations of impact strength to inclusions showed that the dynamic strength of steel is lowered by the presence of visible counted inclusions, but that other factors comprised in the term "body" have a marked influence. The previous work was carried out on selected steels from a single source, so that the body factor was purposely minimized, but even under these conditions it was found that inclusion counting or the use of the commercial inclusion rating is not satisfactory. The tensile-impact test, however, was indicated as a satisfactory measure of dynamic strength. It was further suggested that the tensile-impact test should be so standardized as to be suitable for use in specifications, and that the hardness factor should be worked out over a sufficient range to admit ready commercial use of the tensile-impact test. In accordance with these suggestions, and in view of the fact that the steels reported in the previous paper were selected and treated so as to have a minimum variation in body, hardness and structure, further work has been performed on a variety of steels which are not limited by these conditions. The word "body" is used here for want of a better term. It is simply a convenient expression which comprises the effect, of the various unknown factors that modify the dynamic strength of the steel. Thus at our present state of knowledge, the writers have chosen to consider hardness, structure and counted inclusion content as factors not comprised in the term "body," and such factors as raw materials, process of melting, fabricating, etc., as comprised in the term "body." Numerous grades of steels made in several ways have been taken from different sources and have been heat-treated to varying hardness by normalizing and by quenching and drawing. The results, therefore, may be considered to be generally applicable to current engineering steels. A certain limitation with respect to the hardness at which steel should be tested still seems necessary. The upper limit of this hardness range has

Jan 1, 1931

The first mention of the occurrence of native copper near Lake Superior is found in a book by Lagarde, published in 1636. The letters of the Jesuit missionaries in the seventeenth century refer to the use of this copper by the Indians. Francesco Bressani, an Italian friar, says, in 1653: "There is a copper ore, which is very pure, and which has no need of passing through the fire; but it is in places far distant and hard to reach. We have seen it in the hands of the barbarians".* Father Jerome Lalemant, writing in 1659, says that the coast of Lake Superior is "enriched with copper of such excellence that pieces as large as one's fist are found, all refined.† These pieces of copper were hoarded by the Indians as mascots. The mention of the metal as having been already refined by nature recalls the fact that the old Greek historians spoke of gold-dust as being apuron, or not needing the fire. Father Claude Allouez,‡ writing in 1666, says: "One often finds at the bottom of the water [of Lake Superior] pieces of pure copper, of ten and twenty livres [pounds] weight. I have several times seen such pieces in the savages' hands; and since they are superstitious [as if the padres themselves were not!], they- keep them as so many divinities, or as presents which the gods dwelling beneath the water have given them, and on which their welfare is to depend. For this reason they preserve these pieces of copper, wrapped up, among their most precious possessions".

Jan 1, 1932

By Charles H. Behre

SLATE (Thonschiefer, German; ardoise, French) is a rock, an aggregation of mineral grains, occurring in nature, which is used for roofing and other special purposes. It is finely granular and crystalline and generally derived from an originally clayey bed or series of beds. As a result of its having been put under essentially horizontal compression by geologic forces, this material now has its particles elongated and flattened so as to yield a very good rock cleavage along the flat surfaces of the minerals, a feature entirely independent of the original bedding in the rock. This is the gist of the definition adopted by the Committee on Slate of the American Society for Testing Materials. Slate differs in varying degrees from most other common rocks (such as limestone, sandstone, granite, and "trap") in chemical and mineral composition. Its most characteristic feature, however, is its tendency to fracture along a series of very nearly parallel and very closely spaced smooth planes, called cleavage planes. This property of cleaving, above all else, gives slate its industrial value. ORIGIN AND MODE OF OCCURRENCE Most of the features of slate might be anticipated from its origin. Being a rock rather than a mineral, its composition may vary consider- ably without impairment of value. In most slates, the material of which the rock is now composed was once deposited as clay on the bottom of a lake or sea. Subsequently these clayey strata were compressed by the kind of lateral pressure that folds rock strata, the minerals of the clay being changed or metamorphosed. In the chemical reaction involved, new and essentially plane-shaped minerals belonging to the mica groups were developed. Other minerals were formed but micas generally pre- dominated. These were oriented so that their two longer dimensions are approximately at right angles to the last effective direction of pressure. Since the crystals are thus subparallel, fractures can be developed easily along their surfaces, much as cards can be separated by inserting a knife blade between them. For the foregoing reasons, slate is found in noteworthy amounts

Jan 1, 1949

By C. D. Gilpin, Franklin Moeller

The application of electric power for driving mine hoists handling heavy loads at high speeds has recently been extended by the installation of what is probably the largest electrically driven hoist in this country at the Granite Mountain shaft of the North Butte Mining Co., Butte, Mont. While the weight of rock which is hoisted by this machine is not the largest now being handled by electric mine hoists, the speed of hoisting is so, and the combination of the high speed with the heavy load has resulted in a machine of considerable interest to all those actively engaged in mining. Aside from mere considcration of size, this installation deserves attention because of the careful attention given, not only to the question of economy of operation, but to the details of construction and installation of the entire equipment. The conditions to be met in this installation were as follows: Weight of rock to be raised per trip, 7 gross tons........... 15,680 1b. Weight of skip.......................................... 8,000 1b. Weight of cage.......................................... 1,800 1b. Maximum depth of hoisting.............................. 4,000 ft. Diameter of rope.......................................... 15/8 Total weight suspended on one rope from drum............. 42,000 1b. Normal hoisting speed.................................... 2,700 ft. per minute. Maximum hoisting speed.................................. 3,000 ft. per minute. Desired capacity-200 tons per hour from 4,000 ft. depth. The ore is mined in several levels and hoisting is carried on from the 800-ft. level down to the 2,700-ft., which is at present the maximum depth from which the ore is raised regularly. Development is proceeding and a depth of 2,900 ft. has already been reached. The rock is handled underground in cars holding % ton, and about 10 cars are the usual load for a skip. All of the ore is dumped into underground bins, which are of diffcrent capacities varying up to 250 tons. From the bins the ore is fed into the skips without passing into measuring pockets. At the surface the

Jan 1, 1916

By Cyril Smith

ALTHOUGH not of the same importance as electrical conductivity, the capacity for conducting heat is nevertheless a very important property of metals and alloys. A knowledge of thermal conductivity is of value in selecting alloys for many purposes and in the calculation of the efficiency of apparatus which is being designed. Unfortunately, the determination of thermal conductivity is extremely slow and tedious, consequently few data have been obtained. A further reason for the lack of information is that there has long been an impression that the thermal conductivity of an alloy is directly proportional to the electrical conductivity and that it can therefore be calculated from the latter. The Wiedemann-Franz-Lorenz law of constant ratio of the two conductivities holds with a considerable degree of precision for all the pure metals, but appreciable deviations occur in certain alloys-particularly those containing nickel-and it seems difficult to predict exactly what the ratio will be. Therefore direct determinations of thermal conductivity should be made whenever the results are, needed with any accuracy. This research is intended eventually to cover all the alloys of copper that are of commercial importance, including the binary alloys of copper with zinc, tin, aluminum, nickel, silicon, manganese, cadmium and phosphorus, and the ternary alloys copper-nickel-zinc, copper-nickel-silicon, copper-manganese-silicon, copper-zinc-tin, etc. Most of these alloys are customarily used in the wrought condition and therefore were tested in the form of annealed rods. A limited number of sand castings were also obtained and examined. This paper contains a complete review of all the previous work that has been done on copper alloys, and includes a detailed description of the apparatus and method of procedure used in the present research, together with the new results obtained on the copper-zinc series, which is the only one completed at the present time. Subsequent papers describing the other alloys will contain the experimental results and discussion only.

Jan 1, 1930

By J. T. Crawford

COAL-CLEANING plants using the launder process generally wash the fine coal (minus 3/8 or minus 5/16-in.) separately in a plant consisting of washing launders or troughs placed one below another and sometimes supplemented by additional washing equipment such as tables and jigs. The coal and its associated impurities enters the feed end of the top launder, with a current of push water. As the material moves along the impurities, being heavier than coal, settle toward the bottom of the launder and are drawn off, with some coal, through "free discharge" boxes to the launder below. These boxes were given their name because their discharge falls freely; that is, it does not discharge into a water seal. Thus the impurities are progressively concentrated in the lower launders until box products are sufficiently free of coal to be discharged to refuse. The overflows of the upper launders go to clean coal while the overflow of the lowest launder, and perhaps that of the one immedi-ately above, is usually recirculated to the plant feed. Thus the bulk of the clean coal is removed rapidly and the impurities are concentrated more slowly. The chief purpose of this paper is to present the cleaning data of such a plant under different operating conditions.

Jan 1, 1940

By AIME AIME

MANY of the important papers to be presented at the World Congress of Engineering at Tokyo, in November, 1929, are being furnished by members of A.I.M.E. and a list of them is given below: "Fifty Years of Physical Metallurgy,,-by H. M. Boylston, Case School of Applied Science, Cleveland, Ohio.

Jan 1, 1929

By F. B. Speaker

MUCH of White Pine's success is due to the mechanization of mining operations and the development of an efficient beneficiation process to extract usable copper from the low-grade ore (averaging slightly more than 1 pct copper content). When the mine was first opened, all ore was trucked to a conveyor system installed in the slope leading out of the mine. But as new mining areas have been opened up at increasing distances from the slope, conveyors have replaced the trucks for much of the haulage. This conveyor program is expected to continue as mining progresses. Here is how the present underground system functions: Run-of-mine ore is dumped into two truck hoppers and withdrawn from the bottom of each hopper by a 60-in. apron feeder 22 ft long (see diagram). Collecting conveyors 54 in. wide and 44 ft long receive the material from the apron feeders and discharge to two main-line 54-in. conveyors, one 2000 ft and the other 2600 ft long. Operating at 312 fpm and handling 1200 tph, the main-line conveyors converge near the bottom of the tunnel leading out of the mine and discharge into two 72x168-in. Vibrex screens. Ore under 8 in. goes directly to the bin beneath. The oversize is fed to two 32x40-in. jaw crushers and after crushing joins the 8-in. material in the bin.

Jan 12, 1957

By Louis A. Mattson, Winthrop A. Rowe, John T. Cumberlidge, Victor M. Mejia

The parent ultramafic of Nickel Mountain is an alpine-peri-dotite. Compositional layering and late stage dunites suggest the intrusive crystallized in the upper mantle or lower crust. The ultramafic mass was fault emplaced in the upper crust, probably during upper Jurassic time. Soil, saprolite and silica boxwork nickeliferous ores were formed over the Nickel Mountain peridotite during the development and later destruction of the Klamath peneplane. A complex fault pattern was produced by irregular gravity displacements along fault surfaces during the relative uplift of Nickel Mountain. The majority of the ores occur in the fractured hanging wall of these gravity faults. Consequently, structure mapping is important for mining purposes. Ore types at Riddle are classified on the basis of MgO, Fe, and Si02 contents as well as textures. The chemical, mineralogical and textural differences of the various ore types reflect differences in weathering histories. Satellitic ore bodies occur peripherally to Nickel Mountain. These are erosional remnants of landslides and large gravity fault blocks from Nickel Mountain.

Jan 1, 1976

By E. P. Pfleider

IT is generally believed that the amount of diamond drilling will increase appreciably in the next decade, as the search for minerals throughout the world becomes more difficult and intense. An attendant problem may be one of short diamond supply, resulting in higher bit and drilling cost. With this background, the U. S. Bureau of Mines1 and the School of Mines at the University of Minnesota2 have established comprehensive research programs in diamond drilling. One of the several aims is the design of a more efficient bit, which would lower diamond consumption and increase rate of advance, both essential in reducing drilling costs.

Jan 2, 1953

By T. F. Adams, D. P. Morse

Tunneling is primarily an excavating cycle consisting of a sequence of operations: drilling, shooting, ventilating, mucking, and erecting supports, if necessary. However, the type and condition of the ground that is being worked, as well as the size and shape of the tunnel, determine the rate of advance. In addition developments in drilling, ventilation, mucking, and haulage equipment have contributed to faster tunneling. Geology: This discussion will be limited primarily to rock tunnels or those which require the use of explosives, and the cost and hazards depend primarily on the condition of the rock which may be broken, decomposed, and contain water with gas. Advance geological study is an important part of any tunnel work and helps to minimize serious miscalculations. The geology itself, at best, is a matter of experience and prediction and it is not so much a matter of the types of rock the tunnel may go through, but a knowledge of the class and intensity of the rock defects that may be encountered.

Jan 4, 1958

By Donald H. McLaughlin

THE primary function of the mining engineer is to find mineral deposits and fuels in the accessible rocks of the earth and to recover them for the vast needs of our complicated civilization. On him has been placed the responsibility for the exploitation of the nation's and world's mineral resources. The degree to which the minerals of the earth have been utilized serves to an extent as a measure of man's material advancement, as well as an index of the relative strength of nations. The natural endowment of lands, varies greatly, but the intellectual energy of a people is revealed by the way in which they take advantage of their heritage of minerals or reach out to less developed regions by exporting their engineering skill as well as capital to secure the raw materials they need.

Jan 2, 1953