Search Documents

By Benjamin Moore

AT present the demands of the United States for strontium are met by imports from Germany, England and Canada, which vary considerably in proportions of ore and finished salts, in tonnage and in value. Statistics for the period 1926-1932 are given in Table 1. Domestic deposits are TABLE 1.-Strontium Imported into the United States, 1926-1932° Ore Chemicals Year Short Tons Value Pounds Value 1926 2,200 $58,159 5,433,044 $115,436 1927 1,356 58,711 4,233,816 149,383 1928 759 31,157 3,380,464 136,561 1929 973 45,505 4,578,327 196,233 1930 220 10,459 2,153,788 104,807 1931 (260 lbs.) 123 1,742,714 83,564 1932 5 276 469,481 20,910 a Mineral Industry (1934) 42, 61. known in many states, but the larger and purer ones are in the West, particularly in the desert region of southeastern California and western Arizona. These deposits are large enough to command interest, par-ticularly in consideration of future cheap power at the Boulder Dam. The deposits described in this paper were examined during an investi¬gation of the, mineral resources of the Boulder Dam region by the United States Geological Survey for the United States Bureau of Reclamation' in the spring of 1934. Mr. D. F. Hewett, who had general charge of the investigation, Mr. W. T. Schaller and Mr. M. I. Goldman contributed many helpful suggestions. Mr. N. H. Harshman assisted efficiently during the field work.

Jan 1, 1935

OPEN-HEARTH refractories are not merely an accessory to the furnace. They are the furnace, to all intents and purposes. The steel work of the main structure is merely an open frame which helps to support the refractories ; and the regenerators, a necessary part of the furnace system, consist almost entirely of refractories. Not only do refractories constitute the essential part of the furnace, but they also carry the liquid steel all the way to the point where it begins to solidify. On leaving the furnace the liquid passes through a refractory runner into a refractory-lined ladle, then through a refractory nozzle closed by a refractory stopper on the end of a rod protected by refractory sleeve bricks. The liquid is sometimes sent through an additional refractory- lined tundish, a supplementary ladle, or a refractory runner for bottom pouring, until it finally enters the iron mold in which it solidifies. Even in the mold, refractory materials are sometimes used to provide a nonconducting "hot top." This series, from runner and ladle to hot top, inclusive, is often referred to collectively as the "pouring-pit refractories." REFRACTORY RAW MATERIALS The raw materials available are best classified into basic and acid types. The principal basic raw materials are magnesite, dolomite, and chrome ore. The principal acid materials are silica in various natural forms, and fireclay. Magnesite. Austria was the principal source of magnesite (MgCO3) until recent years, when the Province of Quebec, in Canada, and the states of Nevada and Washington became important sources for the American steel industry. More recently these natural sources have been supplemented by the so-called "sea-water magnesite"-which is the name somewhat incorrectly given to magnesium hydroxide obtained as one of the products

Jan 1, 1964

By Auguste J. Rosh

The use of titaniferous ores in the blast-furnace has been the subject of much controversy for many years. Divers objections have been raised against them, and, for one cause or another, the verdict

Jan 1, 1893

By J. W. R. Rayner

THE conventional method of making water gas involves individual plants for the separate carbonization of coal to coke and the subsequent gasification of coke with steam. The process demands lump coke, preferably made from the best quality of coking coals. The ash in the coke should have a high melting point and the gasification process suffers a loss of efficiency when cokes with law ash-melting points are used. In Britain, these coals are generally the most expensive and they are readily available only in certain localities. The coals not suitable for making lump coke, or yielding only poor quality coke, are much more widely available and are generally cheaper. DEVELOPMENT OF ALTERNATIVE PROCESSES In Germany, processes have been developed and operated commercially for the production of water gas from very low-rank coals such as brown coal and lignites, but much less effort has been spent on processes to use coals of intermediate rank, which are widely available in Britain. The brown-coal processes use coal in the form of either dust or briquettes. The most successful of the dust-gasification methods is the Winkler process, which made a substantial contribution to German oil production during the war. It uses coal in the site range 0 to 8 mm and the fuel bed is blown with a mixture of oxygen and steam at a rate high enough to give it a characteristic boiling motion or, in present-day phraseology, at a rate more than sufficient to fluidize it (Fig. 1). Air cannot be used to provide the heat required for gasification, for various reasons. In the first place, to make the process continuous by mixing air and steam would involve the production of a lean gas-containing much nitrogen. If a separate blow were used, a large amount of potential heat would be lost because the blow gas in such a process would contain a very high percentage of carbon monoxide. Oxygen is necessary therefore and oxygen remains relatively expensive for use in gasification. In the Winkler generator, formation of clinker caused by local overheating does not occur, because of the mobility and high heat transfer of a fluidized bed. These properties of fluidized dusts have been used most successfully

Jan 1, 1953

By E. DeGolyer

The only known direct method of discovering oil deposits is by the drilling of test wells. Such exploration is always hazardous and generally very costly. The problem of the prospector, therefore, is to select test sites that are favorably located and so to reduce the odds against his venture. Early in the history of the oil industry, it was realized that oil and gas deposits, other conditions being favorable, were usually found in anticlinal types of structure. This very undestandable and rational habit of occurrence furnished the first substantial clue to the prospector. Oil occurs in sedimentary rocks, and beds of such rocks are deposited originally in approximately parallel layers. An anticline at the surface, therefore, could be accepted as an indication of an anticline in lower beds. Structural geology became the tool of the prospector, and by its use in the past two decades the majority of the known important oil deposits of the world have been discovered. This is but a partial, and the simplest, statement of the problem, Nine-tenths and more of the important oil pools of the world belong to the great class of accumulations controlled by structural traps—anti-clines, faulted structures, salt domes, etc.—but by no means all of these structures are clearly or adequately expressed at the surface. As the more obvious anticlines were explored and the search for new deposits led to the testing of progressively deeper beds, it became more and more apparent that marked favorable structures involving petroliferous rocks can, and do, exist without any marked surface expression. There are great areas where the surface, covered by some masking material such as water, alluvium, glacial deposits, or sand dunes, affords no clue to structural conditions in the subsurface, and there are also regions where the surface formations are unconformable with the oil-bearing formations. The structure in which the prospector is fundamentally interested is that of the oil-bearing formation itself, together with roof and floor beds. No other geologic information is of interest or importance to him except as it affords clues to the stratigraphy and structure of the supposed oil-bearing formations.

Jan 1, 1932

By Charles H. Behre

UNDER the caption "fault," geologists intend to include all mass movements of solid rocks over adjacent rock masses. When these are studied long after their origin, however, circumstances make it possible to recognize as "fault" only formations showing clear evidence of actual movement of one side with respect to the other. Necessarily the chief evidence consists of the offset of a vein, bed, or other key structure. Planes of movement parallel to the bedding, or nearly so, are recognized with difficulty or are overlooked and hence many important faults are wholly unrecorded. Indeed, among standard American references on structural geology, one alone emphasizes the importance of bedding-plane movements and that one only briefly1. For some time the writer, cognizant of this difficulty, has paid special attention to such movements, both as observed in the field and as recorded in the literature. It is believed that enough data are now at hand to justify a short discussion. Its purposes are fivefold. It is desired first to briefly classify and describe at least the more common kinds of bedding-plane faults, and second, to examine the causes and manner of their formation, at least in instances where the subject has not yet been well covered by other investigators. Third, certain by-products of bedding- lane movements are of such conspicuous importance to the economic geologist and mining engineer as to merit mention. Fourth, concrete illustrations should be placed before the reader in order to lend reality and to furnish a basis of comparison with his experience; such illustrations will necessarily be scattered through the text of this paper. They are only in part from the writer's own field observations. The fifth and prime objective of this paper is to direct attention to the great importance of movements on the bedding planes, in the hope that the recognition of such movements and their significance may simplify mining problems.

Jan 1, 1937

By C. S. Blair

The development of a geological department as an integral part of the Tennessee Coal, Iron & Railroad Co. in the Birmingham district, Alabama, in 1908 was an innovation probably unique for any mining organization south of the Ohio River. At that time a few of the oil companies were starting geological departments, but there were no geologists among the larger industrial organizations. The Tennessee Coal, Iron & Railroad Co. had been a substantial producer of pig iron for many years and was just getting a start in the manufacture of steel products from the pig iron. It had large acreages of coal land, ore land and timber land, but there was lacking the detailed knowledge of the possible mineral resources of much of its territory, and this territory at that time covered an area in the neighborhood of 500,000 acres in the states of Alabama, Tennessee and Georgia. Those responsible for the operations of the mining properties, not being familiar with the kind of help that might be expected from geologic work, were decidedly skeptical of the utility of the work. Therefore it was necessary to develop cooperation with the mining organization, by not infringing upon its functions, and by developing the work in such a manner as to demonstrate to the mining department its practical utility. In the first instance the man responsible for a mining operation is apt to assume the attitude that the geologist is a blockader, because the geologist, unfortunately, is obliged to point out difficulties in the carrying out of mining operations in the way originally planned. He points out the dangers of mining out one coal or metal seam at the ultimate expense of an upper or lower seam, and he develops structural features, such as faults and folds, which call to the attention of the mining operator difficulties in his future operations, which the latter had not anticipated. Eventually, however, the value of having these data became apparent to the Tennessee Coal, Iron and Railroad Co., and the operators not only welcomed the geological work and cooperated fully in its acquisition of essential information, but reached the point of asking assistance and advice; and complete coordination of the two activities has existed for many years.

Jan 1, 1935

By C. S. Blair

The development of a geological department as an integral part of the Tennessee Coal, Iron & Railroad Co. in the Birmingham district, Alabama, in 1908 was an innovation probably unique for any mining organization south of the Ohio River. At that time a few of the oil companies were starting geological departments, but there were no geologists among the larger industrial organizations. The Tennessee Coal, Iron & Railroad Co. had been a substantial producer of pig iron for many years and was just getting a start in the manufacture of steel products from the pig iron. It had large acreages of coal land, ore land and timber land, but there was lacking the detailed knowledge of the possible mineral resources of much of its territory, and this territory at that time covered an area in the neighborhood of 500,000 acres in the states of Alabama, Tennessee and Georgia. Those responsible for the operations of the mining properties, not being familiar with the kind of help that might be expected from geologic work, were decidedly skeptical of the utility of the work. Therefore it was necessary to develop cooperation with the mining organization, by not infringing upon its functions, and by developing the work in such a manner as to demonstrate to the mining department its practical utility. In the first instance the man responsible for a mining operation is apt to assume the attitude that the geologist is a blockader, because the geologist, unfortunately, is obliged to point out difficulties in the carrying out of mining operations in the way originally planned. He points out the dangers of mining out one coal or metal seam at the ultimate expense of an upper or lower seam, and he develops structural features, such as faults and folds, which call to the attention of the mining operator difficulties in his future operations, which the latter had not anticipated. Eventually, however, the value of having these data became apparent to the Tennessee Coal, Iron and Railroad Co., and the operators not only welcomed the geological work and cooperated fully in its acquisition of essential information, but reached the point of asking assistance and advice; and complete coordination of the two activities has existed for many years.

Jan 1, 1935

By Lawrence B. Wright

THE Republic district, Washington, is of new interest because of the discovery of new gold-silver ore within a unique structural pattern. The camp was revived in 1937 following installation of a plant to treat low-grade disseminated ore at Knob Hill and further stimulation followed discovery of "cross vein" breccia ores in 1939. Previous writers 1-2 ascribed the quartz veins to a latite porphyry stock, but are in disagreement as to its precise location and extent. This study leads to the conclusion that the ores have a more profound parentage linked to a broad system of thrust faults and folds, the mechanical origin of which is related to a southward trending (Sanpoil) syncline connecting with the Lewis and Clark zone of shift described by Billingsley and Locke3 in 1939. The Republic anticline and a cross anticline recumbent against Cretaceous granodiorite, and involving some 4000 ft of Eocene andesite flows and early Miocene lake beds, localize the ores, mainly along the east flank, in a series of openings simulating drag folds and steeper than the folded flows. These broad structural features no doubt reach deeply into the basement rocks, where at appropriate crossings and junctions it is suggested that heat effects gave rise to oremaking materials, including, in this instance, intrusive breccias that later were mineralized, and comprising the broader bodies of new ores. The breccia ore is seen crosscutting the earlier narrow quartz veins with a welding of the two at junction areas by a second surge of ore minerals. The ore mined and developed since 1937 equals district production from 1896 to 1937. The ores are typified by cherty quartz, adularia and some barite, with fine pyrite and marcasite, polybasite, pyrargyrite, tetrahedrite and gold. Selenium is present, possibly with gold, as a normal selenide. The disseminated ores, as well as the vein and breccia ores, are localized principally in one 500-ft flow (Knob Hill andesite), which has been traced around the crest of the low northward-plunging Republic anticline. The gold-silver ratio in the earlier narrow veins is about 1 to 4 and in the disseminated and breccia ores, 1 to 7. The latter higher silver ratio is deemed to reflect the character of the second surge of mineralization. Sills and dikes of the Columbia River (Miocene) basalt cut the folded structure and ore, thus placing the mineralization in the middle Miocene.

Jan 1, 1947

By C. S. Blair

THE development of a geological department as an integral part of the Tennessee Coal, Iron & Railroad Co. in the Birmingham district, Ala-bama, in 1908 was an innovation probably unique for any mining organ-ization south of the Ohio River, At that time a few of the oil companies were starting geological departments, but there were no geologists among the larger industrial organizations. The Tennessee Coal, Iron & Railroad Co. had been a substantial producer of pig iron for many years and was just getting a start in the manufacture of steel products from the pig iron. It had large acreages of coal land, ore land and timber land, but there was lacking the detailed knowledge of the possible mineral resources of much (of its territory, and this territory at that time covered an area in the neighborhood of 500,000 acres in the states of Alabama, Tennessee and Georgia. Those responsible for the operations of the mining properties, not being familiar with the kind of help that might be expected from geologic work, were decidedly skeptical of the utility of the work. Therefore it was necessary to develop cooperation with the mining organization, by not infringing upon its functions, and by developing the work in such a manner as to demonstrate to the mining department its practical utility. In the first instance the man responsible for a mining operation is apt to assume the attitude that the geologist is a blockader, because the geologist, unfortunately, is obliged to point out difficulties in the carrying out of mining operations in the way originally planned. He points out the dangers of mining out one coal or metal seam at the ultimate expense of an upper or lower seam, and he develops structural features, such as faults and folds, which call to the attention of the mining operator diffi-culties in his future operations, which the latter had not anticipated. Eventually, however, -the value of having these data became ap to the Tennessee Coal, Iron and Railroad Co., and the operators not only welcomed the geological work and cooperated fully in its acquisition of essential information, but reached the point of asking assistance and advice; and complete coordination of the two activities has existed for many years.

Jan 1, 1933

By W. W. Anderson

A formula for quantitative efficiency is proposed, in which the efficiency value is a function of the improperly distributed material at the, gravity of separation effected by the cleaning equipment. The misplaced material is expressed as a percentage of the total material discharged from the equipment. Numerous examples are given, demonstrating application of the formula to various types of separation, including multiple-product separations.

Jan 1, 1950

By G. St. J. Perrot, S. P. Kinney

Consumers of metallurgical coke are agreed that the quality of their fuel plays an important part in the performance of the furnace. Less unanimous agreement is evident when the properties of a desirable coke are discussed or when consideration is made of suitable testing methods by which the worth of a coke for metallurgical purposes may be determined quantitatively. Much has been written of the importance of combustibility as a factor in determining the performance of coke in the blast furnace and it is generally believed that cokes vary widely in this respect. The usual operating data of the furnace afford little evidence as to the combustibility of the fuel. As a part of a general investigation of the properties of metallurgical coke, the Bureau of Mines has explored the hearth combustion zone in a number of blast furnaces by means of water-cooled gas sampling tubes driven into the hearth through the tuyeres. The attempt has been made to determine the difference in combustibility of cokes varying widely in physical properties. Data have also been obtained in an experimental combustion furnace at the Bureau laboratories in Pittsburgh. This paper gives the results of experiments, made at eleven blast furnaces, in which the composition of the gases was determined at various points in the hearth in the plane of the tuyeres. Further work is in progress in which the zone above the tuyeres will be explored. Factors Affecting Coke Combustibility Brassertl has defined combustibility as the rate of progression of combustion, or, in other words, the speed at which the carbon molecules

Jan 1, 1923

By S. P. Kinney, G. St. J. Perrot

Consumers of metallurgical coke are agreed that the quality of their fuel plays an important part in the performance of the furnace. Less unanimous agreement is evident when the properties of a desirable coke are discussed or when consideration is made of suitable testing methods by which the worth of a coke for metallurgical purposes may be determined quantitatively. Much has been written of the importance of combustibility as a factor in determining the performance of coke in the blast furnace and it is generally believed that cokes vary widely in this respect. The usual operating data of the furnace afford little evidence as to the combustibility of the fuel. As a part of a general investigation of the properties of metallurgical coke, the Bureau of Mines has explored the hearth combustion zone in a number of blast furnaces by means of water-cooled gas sampling tubes driven into the hearth through the tuyeres. The attempt has been made to determine the difference in combustibility of cokes varying widely in physical properties. Data have also been obtained in an experimental combustion furnace at the Bureau laboratories in Pittsburgh. This paper gives the results of experiments, made at eleven blast furnaces, in which the composition of the gases was determined at various points in the hearth in the plane of the tuyeres. Further work is in progress in which the zone above the tuyeres will be explored. Factors Affecting Coke Combustibility Brassertl has defined combustibility as the rate of progression of combustion, or, in other words, the speed at which the carbon molecules

Jan 1, 1923

By Paul J. Bennett, James E. Castle

The kyanite minerals, including kyanite, silimanite, and andalusite, are anhydrous aluminum silicates with the formula Al2O3SiO2. lumortierite and topaz are also included in this group because they are closely allied in composition and thermal behavior. However, leither are mined commercially today. They ire typical metamorphic minerals which are found in metamorphic rocks on every continent. Kyanite minerals are prized chiefly for their refractoriness and are important components in a broad range of acid refractory products, especially in mortars and castables. World production of kyanite minerals is currently about 250,000 tpy and has been increasing at the rate of 3 to 8% a year for many {ears (Anon, 1972). While kyanite minerals lave widespread occurrence, the consumption of kyanite minerals is concentrated in the relatively few highly industrialized areas where refractories are manufactured, and which in turn are typically close to the major iron and steel producing regions of the world. Thus northern Europe, England, the United States, and Japan are the principal consumers of refractories and kyanite minerals. Of these countries only the U.S. is a significant producer. The largest use for domestic kyanite, both raw and calcined, is in the manufacture of refractory mortars, cements, castables, and plastic ramming mixes. In these applications kyanite constitutes from 10 to 40% of the mixture, the balance being refractory clays and coarser grog materials. A certain proportion of raw kyanite is used to offset the shrinking of the clay binder, whereas the calcined kyanite is used in the coarser sizes for body. Certain high grade refractory shapes and kiln furniture are composed chiefly of graded sizes of calcined kyanite bonded with a little ball clay. In most applications, however, kyanite is used only to fortify the mix or as a minor ingredient. Some manufacturers of mullite brick use domestic calcined kyanite for the fine-grained portion of the brick, but seldom in quantities exceeding 10% by weight. Kyanite is used by ceramic manufacturers of wall tile and sanitary ware to offset shrinkage and cracking after firing. Indian kyanite has traditionally been used to make the coarse grog sizes needed for the manufacture of mullite brick, and for the grog portions of mortar, cement, and castable mixes. It has been largely replaced, however, by synthetic mullite, high fired flint, and diaspore clay or calcined bauxite for other applications. Indian kyanite is available in lump as well as in granules and concentrates, as are sillimanite materials from India and South Africa. Andalusite is available as 8 mesh granules and as fines with chemical analyses not unlike those of domestic kyanites. From time to time and from place to place minor amounts of other aluminum silicate minerals such as dumortier- ite, topaz, and pyrophyllite have been made available at various prices and specifications, but have not been significant factors in the refractory industry. A mixture of kyanite and sillimanite of relatively fine grain-size and of low iron content was at one time offered to the molding sand industry by the Du Pont Co. as a byproduct from their deposits of heavy

Jan 1, 1975

By Y. C. Liu, G. A. Alers

The anisotropy of Young's modules has been measured in a series of Cu-Zn alloys containing from 1 to 28 wt pct Zn and cold-rolled to 97.5 pct reduction in thickness. These modulus data show a transition in texture as a function of zinc content. In alloys containing 3 pct Zn or less, the texture is essentially that of copper. A transition is clearly seen to develop in 5 and 8 pct Zn alloys, and to have been completed in a 12 pct Zn alloy. Increasing the proportion of zinc to 28 pct does not produce any further changes in texture. The ease and clarity with which this texture transition can be seen in the modulus data is in great contrast with the inccertainty in the visual detertiination of the range of texture transition from a series of pole figures. It is also shown that the rolling texture of the high zinc content alloys cannot be a one-COIIIponenl texture, characterized by the (110)(112) ideal orientations, as usually assumed. A second, quite important component must also be present. Furthermore, the present data are inconsistent with matrix orientations on which the "oriented growth" hypothesis of the Formation of recrystallization textures is based. THE rolling textures of binary fcc alloy systems have generally been considered to lie between two terminal textures. One of these terminal textures is the copper type and the other is the 70:30 brass type. Alloys of intermediate solute content exhibit a texture which is said to be a transition between the two terminal textures. On the basis of efforts to correlate rolling and recrystallization textures, two concepts have been advanced in the literature on the nature of these transition textures. One school1 suggests that the addition of alloying elements, e.g., zinc, causes a gradual rotation about one of the (111) poles from the (358)( 523) ideal orientation of the copper-type rolling texture to the terminal {1 10)( 112) ideal orientation used to describe the rolling texture of 70:30 brass. This concept is depicted in Fig. 1 with the angle of rotation corresponding approximately to the zinc content and is designated here as the "rotational concept", since the ideal orientation of the transition textures varies continuously with alloy content. The other concept,' the "mixture concept", suggests that the copper-type rolling texture is a two-component texture. {358) (523) and {110)(112). The addition of alloying elements affects only quantitatively the relative amounts of these two components—a decrease in the amount of material in the {385}(523) orientation and an increase of that in the {110)(112) orientation with increasing solute content. An experimental distinction between these two concepts is essential to a better understanding of both the mechanism of formation of rolling textures and the subsequent formation of recrystailization textures in fcc metals. Because of the lack of resolution inherent in pole figures, it has not been possible to differentiate between the two concepts on the basis of this data. Both concepts, in fact, make use of the same set of pole figures but interpret them in a manner acco-rding to the view held.'" Experimental results obtained from inverse pole figures or selected-area electron diffraction3j4 simply -yield more refined pole figures but do not eliminate the ambiguity of interpretation. Quantitative measurement of an entirely different, orientation-dependent property must thus be considered

Jan 1, 1967

By Herbert Clark Hoover, Lou Henry Hoover

QUALITIES which the perfect miner should possess and the arguments which are urged for and against the arts of mining and metallurgy, as well as the people occupied in the industry, I have sufficiently discussed in the first Book. Now I have determined to give more ample information concerning the miners. In the first place, it is indispensable that they should worship God with reverence, and that they understand the matters of which I am going to speak, and that they take good care that each individual performs his duties efficiently and diligently. It is decreed by Divine Providence that those who know what they ought to do and then take care to do it properly, for the most part meet with good fortune in all they undertake; on the other hand, misfortune overtakes the indolent and those who are careless in their work. No person indeed can, without peat and sustained effort and labour, store in his mind the knowledge of every portion of the metallic arts which are involved in operating mines. If. a man has the means of paying the necessary expense, he hires as many men as he needs, and sends them to the various works. Thus formerly Sosias, the Thracian, sent into the silver mines a thousand slaves whom he had hired from the Athenian Nicias, the son of Niceratus1. But if a man cannot afford the expenditure he chooses of the various kinds of mining that work which he himself can most easily and efficiently do. Of these kinds, the two most important are the making prospect trenches and the washing of the sands of rivers, for out of these sands are often collected gold dust, or certain black stones from which tin is smelted, or even gems are sometimes found in them ; the trenching occasionally lays bare at the grass-roots veins which are found rich in metals. If therefore by skill or by luck, such sands or veins shall fall into his hands, he will be able to establish his fortune without expenditure, and from poverty rise to wealth. If on the contrary, his hopes are not realised, then he can desist from washing or digging. When anyone, in an endeavour to increase his fortune, meets the expenditure of a mine alone, it is of great importance that he should attend to his works and personally superintend everything that he has ordered to be done. For this reason, he should either have his dwelling at the mine,

Jan 1, 1950

By Russell G. Haworth

Three companies, United States Potash Company, Potash Company of America, and International Minerals and Chemical Corporation, are now operating potash mines and refineries in the Carlsbad, New Mexico, area. The three mines are located approximately twenty miles east of Carlsbad. The deposits have been found ideal for mechanized mining methods. This summary has been compiled from information made available by the three operating companies.

Jan 1, 1949

By R. Schuhmann Jr., P. J. Ensio

As a first step in a study of the physical chemistry of copper-smelting slags, experimental measurements were made of the oxygen pressure of simple iron-silicate slags in equilibrium with solid iron. The experiments consisted in bubbling CO2-CO mixtures through the slags in iron crucibles and in finding the equilibrium ratios of CO2 to CO. From the data, activities and partial molal heats of solution FeO and SiO2 in the slags were calculated. THE ternary system FeO-Fe,O,-SiO, is the simplest system which can represent adequately the important chemical properties of the slags formed in matte smelting and converting. Accordingly, the experimental study of slags in this system was started as the first step in a general research program on the thermodynamics of copper smelting. A recent paper by one of the authors' outlines this general research program and shows in some detail how information on thermodynamic properties of iron-silicate slags, especially information on oxygen activities, is essential to a full understanding of the chemistry of copper smelting. The FeO-Fe,O,-SiO, system also is the basis of slags produced in other processes, such as acid steelmak-ing processes, and is important in relation to the behavior of silicious refractories. In addition, data on the physicochemical properties of iron-silicate slags should contribute to a general understanding of the nature of slags, since at present such data for all kinds of slags are relatively meager. The principal quantitative information already available on iron-silicate slags consists in Bowen and Schairer's constitution diagram for slags in equilibrium with metallic iron,' Darken and Gurry's complete and precise thermodynamic study of the Fe-0 system,",' and Darken's study of the phase equilibria in the Fe-Si-o system. From the results of this previous work, it was clear that a complete thermodynamic study of ternary iron-silicate melts was a major undertaking which would have to be broken down into parts, including the working out of the ternary equilibrium diagram as well as extensive activity measurements on slags. The experimental measurement of oxygen activity, using CO-CO, and other gas mixtures as yardsticks of oxygen activity, was the basis of Darken and Gurry's study of the Fe-0 system. From the experimental measurements of oxygen activities over a large range of temperatures and compositions, they were able to calculate the activities of other species such as Fe, FeO, Fe,O,, etc., and also the other important thermodynamic properties in the Fe-0 system. At the start of the present investigation, it appeared that the same approach would be fruitful for the study of iron-silicate melts. Also, the experimental measurement of oxygen activities seemed particularly attractive because oxygen activity itself is a quantitative measure of oxidizing or reducing power, which is an important variable in copper-smelting slags. The slag compositions in equilibrium with yFe appeared most suitable for the first investigation of this kind, for the following reasons: 1—Good constitution data2 were available. 2—An iron crucible could be used, thus affording a simple solution to the refractory problem without introducing contarnination. 3—With Fe activity fixed, at unity with respect to a standard state of solid Fe, measurements of 0 activity could be followed by simple calculations of activities of FeO and other Fe-0 complexes and of SiO,. 4—This starting point afforded several possibilities for cross-checking with previous work,

Jan 1, 1952

By H. S. McKnight

One phase of Canada's rapid development in mining and metallurgy during the past few years has been the creation of Canadian Copper Refiners Ltd., and the establishment of its modern electrolytic copper refinery at Montreal East, Quebec. Canadian Copper Refiners Ltd. is made up of three well-known metal firms whose combined activities cover the entire industry from the mine to the market. They are Noranda Mines Ltd., Toronto, Nichols Copper Co., New York, and British Metal Corporation, Ltd., London. Noranda Mines is the principal owner and provides the greater part of the raw material received by the refinery for treatment. Nichols Copper Co. designed and built the plant and is operating it under contract. British Metal Corporation acts as sales agent and markets the refinery's products. Montreal East was chosen as the site of the new refinery only after a careful survey had been made of the entire eastern part of Canada. The location chosen offers many advantages, chief of which arc the relatively low costs of power, labor, fuel and bupplies, and the fact that it is situated on Montreal harbor, the nearest seaport to the points of origin of the ram materials. All incoming material is received by rail. A majority of the plant's product is exported through the port of Montreal to European markets, being handled to the docks in railroad cars. A large proportion of the product is delivered by means of an industrial railway to the adjacent rolling mill of the Canada Wire & Cable Co., Limited. The refinery was designed to treat primarily the copper produced by Noranda Mines, Ltd. and Hudson Bay Mining &. Smelting Co., Ltd., and its rated capacity is 75,000 short tons per year. A general layout of the plant is shown in Fig. 1. Its capacity can be readily doubled, as shown by the dotted lines. Figs. 2 and 3 are sections taken through the furnace department and the tank house respectively. Except for the main office and laboratory and an auxiliary building containing the stores, warehouse, change rooms, compressor room and machine shop, the entire plant is under one roof. The type of building construction consists of reinforced concrete foundations supported on concrete piles, a steel structure covered with Robertson Protected Metal siding and a 3-in.

Jan 1, 1934

By Heihachi Kamura

In this research, the proper temperature for the reduction of iron ores by carbon monoxide was determined. Also, the difference of the rate of reduction on the sizes of ore under four mesh per linear inch was estimated, but no evidence could be found. Rates of reduction on the seven kinds of ore were compared with the results of the experiment, showing a close relation between reducibility and density of ore. Finally, the maximum size of ore that can be reduced in applicable length of time was determined. The author thinks that the process of production of steel may be replaced by low-temperature reduction of iron ores some time in the future. THE reduction of iron oxide, such as Fe203, to iron in the blast furnace is performed principally by carbon monoxide, but partly by solid carbon by the two following reactions: Fe203 + 3CO = 2Fe + 3CO2 2Fe203 + 3C = 4Fe + 3CO2 It is known that reduction by carbon monoxide takes place at a much lower temperature than reduction by carbon and that the reducing action of carbon monoxide progresses to the inside of the ore in lump form by gaseous diffusion. In the reduction by carbon, however, the reducing action takes place only at the contact surface of the ore and carbon, so that the more complete the reduction by carbon monoxide, the more efficient is the operation. However, the reduction does not progress as shown in the foregoing formula, because carbon dioxide acts oxidizingly on the metallic iron to such a degree that when the gaseous composition reaches a certain proportion of carbon dioxide to carbon monoxide, the reduction practically stops, even though the gases are moving slowly through the heated ore. The proportions of carbon monoxide and carbon dioxide in the gas depend on the kind of iron oxide and the temperature of reduction, also the duration of time in the reaction. The longer the time of the reaction, the higher the proportion of carbon dioxide obtained in the gas, but finally it will attain to a condition of equilibrium.

Jan 1, 1925