Search Documents

By John Fulton

The Connellsville coal-field is a separate strip of the upper coal measures, flanking the Chestnut Ridge along its western side. It extends from a point a few miles south of Uniontown, in Fayette County, following a northeasterly course parallel to the trend of Chestnut Ridge, through Fayette and Westmoreland counties, with its terminal prongs resting 011 the southern portion of Indiana County, north of the town of Blairsville. This belt of coking coal will average about three miles in width and over sixty miles in length, affording nearly, if not quite, two hundred square miles of this large coal-bed.

Jan 1, 1885

By Duane N. Goens, Clifford R. Porter

A 91 kg/h (200 lb per hr) pilot plant was constructed according to "Magnex" design. A non-compliance eastern coal which would generate more than 0.85 kg of S02 per GJ (2.0 lb of SO2 per million Btu.) upon burning was brought into compliance less than 0.52 kg of SO2 per GJ (1.2 lb SO2 per million Btu) during continuous operation of the pilot plant. Approximately 85% of the pyritic sulfur was removed while recovering 90% of the Btu of the feed coal. Pilot plant operation is summarized and preliminary economics presented. Present status of the Magnex design program is reviewed.

Jan 2, 1979

By H. B. C. Nitze

In view of the extensive use of vanning-machines in this country, a brief comparison of the results obtained by the plain belt generally employed, and the corrugated belt which was introduced a few years ago, may be of interest. The data given below have been abstracted from a working-journal, and hence lack the precision, and also, in several desirable particulars, the detail, which would naturally have been secured in special experiments ; but they have the advantage of being working-figures, and are sufficient as the basis of a fair comparison between the two kinds of belt working on similar ores. The conditions under which the work was done were the following :

Jan 1, 1893

By R. Hogg, D. W. Fuerstenau

Based on a simplified model for the motion of particulate materials in horizontal, rotating cylinders, approximate expressions have been derived relating the power consumption of a tumbling mill to its dimensions and speed of rotation and to the amount and nature of the charge. The basic assumptions underlying the model are that there is no slip between the charge and the mill shell, that the free surface of the charge remains essentially planar during rotation, and that there is no transfer of momentum from the material flowing down the free surface back to the mill shell. The relationships formulated from this model have been shown to be in excellent agreement with experimental results taken from the literature. While the requirements of the model are most clearly met at low speeds of rotation, the results appear to be valid even for speeds up to 70-80% of the critical speed. Poorer agreement between theory and experiment is found when the charge consists of relatively large particles (balls) and when the filling of the mill exceeds 50% of the available volume. Qualitative explanations of these deviations have been offered.

Jan 1, 1973

By L. G. Huntley

Introduction IN View of the recent advance made in the knowledge of the nature and conditions accompanying the occurrence of oil and gas, and of the recent activity in drilling in Wyoming, Montana, and western Canada, a discussion of the probabilities of obtaining production in such a reservoir as the Dakota sand in general, and in particular districts, is thought by the author to be timely and likely to result in more intelligent operating in certain parts of the territory underlain by this sand. In Canada particularly it is thought that these general considerations have equal if not more significance in a consideration of the oil and gas possibilities of the formations than have the various local conditions.

Jan 6, 1915

By John Hall

THE Fremont test for measuring the energy consumed in breaking a notched bar of steel is not so well known in this country as it deserves to be. The test specimen used in this test is about 3/8 by 1/4 by about 1 1/4 in., notched with a hack saw on the lower side to cause the piece to break at a fixed point. A weight of 10 kg. falling 4 m., and provided with a knife or chisel which strikes the specimen, breaks the test piece by impact. The residual force in the falling weight after it has broken the specimen is recorded by a suitable device, and the difference between the total energy and the residual energy of the weight (in kilogrammeters) is the force consumed in breaking the specimen. An experience of several years with the Fremont testing machine has shown its great value in readily detecting brittleness not revealed by tensile testing or slow bending testing. I this paper it is proposed to discuss (1) the supersensitiveness of the test as applied to cast steel and (2) its value in revealing the effect of heat treatment under certain conditions. .

Jan 7, 1913

By C. W. Vaupell

THE Huitzuco mines lie in north central Guerrero, Mexico; production has been about 90,000 flasks of quicksilver since 1873. Near-surface ores fill extinct mud geysers and the deep deposits are chambered veins, stock-works in brecciated blocks, and replacements in limestone. The epigenetic minerals livingstonite, stibnite and sulphur occur in limestone, gypsum and dolomite through a developed vertical range of 260 meters. The deepest workings expose an increased amount of stibnite, which probably indicates that the lower limit of mercury mineralization is being approached. A resur-gence of heat and water formed geysers over an extended area after the period of mercury mineralization. Mud geysers, which are situated, in the outcrops, contain the secondary mercury minerals, cinnabar and barcenite in the gravel and mud filling the vents. A 150-ton flotation plant is in operation concentrating stope fills that assay 3.0 kg. of mercury per ton. In one open stope, which is more than one hectare in area and 60 m. high, 150,000 tons are available.

Jan 1, 1937

By Z. T. Bieniawski

Tunneling in coal mines includes driving the main haulageways or roadways which serve as the development entries. Although constituting the lifelines of these mines, little attention has been paid to development entries in the United States in terms of systematic pre-construction planning and design. Coal mine tunnels, as the terminology is used in Europe and elsewhere, are understood in the United States to be the main development entries, either in room-and-pillar mining or in longwall mining. These development entries are not tunnels in the traditional sense since they usually are of a multi-entry type involving entries and cross-cuts, and their intersections. Thus, the design of coal mine tunnels is intertwined with the design of coal pillars. This paper summarizes the results of a three-year research project aimed at improving the design of development entries in U.S. coal mining. A design approach has been developed for this purpose and design procedures for roof support in main entries and for pillar sizing are proposed.

Jan 1, 1984

By Strathmore R. B. Cooke, Iwao Iwasaki, Hyung Sup Choi

Oleic acid is the chief ingredient of fatty acids used as collectors in nonsulfide flotation. With a few notable exceptions, the various quantities of saturated and other unsaturated acids comprising the remainder are usually unspecified. There have been occasional investigations to determine the collecting ability of these other acids and their effect on collection with oleic acid, but much remains to be done in this field. Hukki and Vartiainen, on the basis of tests using palmitic, oleic, and linoleic acids and an impure linolenic acid, concluded: "The collecting power of fatty acids used in flotation increases with increasing unsaturation of the hydrocarbon chain." 1 Their work was concerned mainly with the response of ilmenite to the foregoing collectors, although tests were also made with magnetite, pyrite, hematite, and rutile. Cooke and Nummela, employing an al- most identical technical procedure to evaluate flotation of hematite, magnetite, and goethite with various fatty acids, including oleic, linoleic, and linolenic acids of the highest purity obtainable, found: "The effectiveness of 18-carbon unsaturated fatty acids, as collectors for hematite, decreases with increase in the number of non-conjugated double bonds."' In the foregoing investigations, collector efficacy was measured on the basis of reagent addition in moles per liter.

Jan 9, 1959

[ ]

Jan 1, 1938

By Earle J. Klohn

Mining operations have been carried out in British Columbia since the time of the first settlers in the area. The early developments were mainly small volume, high-grade operations, producing small quantities of tailings wastes. In these early days the nearest stream was a logical first choice for tailings disposal. Where streams suitable for accepting the tailings were not available or where streams crossing the International Border could not be used for this purpose, the nearest convenient land site was selected for storing the tailings. Old tailings waste piles exist at many locations in the Province and are readily evident, for example, in the Princeton and Hedley areas. Figs. 1 and 2 are photographs showing the present condition of two of these old tailings dams. [ ]

Jan 1, 1972

By G. M. Lee

SEVERAL improvements have been made in Granby smelting practice since the company abandoned the direct smelting of raw ore in the blast furnaces in June, 1927, in favor of sintered concentrate. These improvements have been made in several fields, but the most novel and outstanding change was the development of a process of concentrating most of the gold, and a somewhat smaller fraction of the silver present, in a small portion of the blister copper produced. The practice of making "copper bottoms" is usually associated with the reverberatory smelting of copper ores containing high percentages of impurities, or of copper matte high in precious metals. It has for its object, in the one case, the production of a major part of the copper relatively free from impurities and, in the other case, the production of a small per¬centage of the copper carrying the major part of the precious metals. Although the blister copper produced at the Anyox plant of the Granby company is remarkably free from deleterious impurities and normally contains no great amount of precious metals, certain economic considerations made it advisable to concentrate the existing precious metals into a relatively small percentage of the blister copper produced. The process devised took advantage of principles and reactions of the usual bottoms processes, but was carried out in the converters instead of in a reverberatory furnace.

Jan 1, 1935

By R. J. Sweigard, R. V. Ramani

Demands on available lands will continue to increase due to the projected population increase and industrial expansion. Though there is an upper limit on available lands, the multi-use nature of the lands will make it possible to meet these demands. However, this will not happen without adequate planning. Land uses can be broadly categorized as nonrenewable and renewable. Lands with minable resources can be dedicated at some Point to the extraction of resources. Such a dedication, however longterm, is only temporary because of the nonrenewable nature of the minable resources. The land will be available before and after mining for other uses. Planning for such lands must have the objective that, as far as practicable, no nonrenewable uses are preempted and no renewable uses are permanently destroyed. This paper addresses primary aspects of this planning process. These aspects include a discussion of planning responsibility, data needs and availability, the integration of mine planning and post-mining land use planning, and a long-term plan for resource conservation and utilization. Minerals, with agriculture and forest products, are the primary sources of wealth. Therefore, to amid land development that may preempt future mineral resource utilization, local planning groups must be aware of the mineralization and mining potential. Much work needs to be done to identify and characterize the mineral resources. Even more land use planning is needed for lands with mineral deposits.

Jan 1, 1985

By W. J. Wrazej

THE measurements on the formation of multi-layered scales on pure iron1 and the metal -lographic examination of the produced layer of FeO, Fe,O,, and Fe2O3 shown in micrographs2 throw much interesting light on this apparently well-known subject. Professor Paidassi announced2 that in a few months7 time further results are going to be published with regard to the growth of Fe2O3 and Fe2O3 layers on an Armco iron as a function of temperature. Because of the very thin layers of Fe2O3 which are shown by Paidassi (Fig. 10 of ref. 2) when samples were scaled in air at 700°C for 4 hr and because this is not in agreement with the present author's previous observations, the following experiment was recently carried out. Polished cylindrical samples 13/64 in. in diam and 1/4 in. long from electrolytic iron used for spectro-graphic work (Hilger, H.S. Iron rods, F.693) and an Armco iron sample 1/4 in. in diam of the same length were suspended in a muffle furnace on Nichrome wire and annealed in air for 4 hr at 700°C 5OC. Because of the known easy peeling off of the Fe2O3 layer which is mainly in the form of powder (purple red dust on the surface) the samples were protected against any draft and shock. After annealing, the samples were cooled in air and placed in the mount-

Jan 1, 1954

By E. H. Tenney

A discussion of the probable future use of coal for power development involves the study of several basic factors, such as future demand for power, the quantity and availability of fuels in direct competition with coal, the price of coal, and a closely related factor—the efficiency and cost of fuel utilization. Predictions based on purely statistical analyses of past coal consumption have definite limitations. For example, statistics showing the relation between coal utilization and total energy consumption from all sources between the years 1890 to 1930 indicate that during that period the energy consumption per person in the United States increased five times, while the coal consumption per person increased only twice1, and there has been an actual decrease in per capita coal consumption since 1920. Figures such as these, compiled by authentic agencies, emphasize the need for caution in attempting estimates as to the future use of coal, and, incidentally, would seem to offer little basis for optimism in the coal industry. They also suggest the value of analyzing broadly the part played in the past by the related factors of power consumption, competitive fuels, coal prices and the efficiency of utilization. Proper weight must also be given in such a study to the present status and limitations of power-plant developments, arid to the question of what the coal industry itself can do to further its own interests arid influence the consumption of its product.

Jan 1, 1936

By L. H. Schwartz, M. V. Nevitt

THE phase Ti2Ni has been described by Laves and Wallbaum,1 who found the phase to be face-centered cubic with 96 atoms per cell, by Duwez and Taylor,2 who confirmed these observations and reported a lattice parameter of 11.333A, and by Rostoker,' who reported the structure to be isomorphous with the double carbide Fe,W,C, type E93, and to have a lattice parameter of 11.29A. In this study a group of isostructural phases has been found among alloys of certain second and third long-period transition elements. The systems investigated included all the combinations of zirconium and hafnium with the Group VIII elements rhodium, palladium, iridium, and platinum. There is evidence that many of these new Ti2Ni-type phases require oxygen for their stability in the temperature ranges in which they were studied. EXPERIMENTAL PROCEDURE Alloy samples weighing 5 g were prepared by arc-melting metals whose purity is indicated in Table I in a helium-argon atmosphere. Samples of the as-cast buttons, wrapped in molybdenum foil and sealed in evacuated quartz tubes, were

Jan 1, 1959

By E. H. Tenney

A discussion of the probable future use of coal for power development involves the study of several basic factors, such as future demand for power, the quantity and availability of fuels in direct competition with coal, the price of coal, and a closely related factor—the efficiency and cost of fuel utilization. Predictions based on purely statistical analyses of past coal consumption have definite limitations. For example, statistics showing the relation between coal utilization and total energy consumption from all sources between the years 1890 to 1930 indicate that during that period the energy consumption per person in the United States increased five times, while the coal consumption per person increased only twice1, and there has been an actual decrease in per capita coal consumption since 1920. Figures such as these, compiled by authentic agencies, emphasize the need for caution in attempting estimates as to the future use of coal, and, incidentally, would seem to offer little basis for optimism in the coal industry. They also suggest the value of analyzing broadly the part played in the past by the related factors of power consumption, competitive fuels, coal prices and the efficiency of utilization. Proper weight must also be given in such a study to the present status and limitations of power-plant developments, arid to the question of what the coal industry itself can do to further its own interests arid influence the consumption of its product.

Jan 1, 1936

By Donald L. King

This paper has been prepared with the objective of providing basic information on thickening equipment as applied to mineral processing plant design. Thus, by design, the content is elementary, yet sufficiently informative to advise the reader concerning the thickening and clarifying process, equipment configurations, installation and operation. Practical considerations are provided for slurry samples for testing, evaluation of testing, preliminary sizing, duty classification, and thickener selection to enhance operation, see icing and control. Illustrations are provided to both inform and demonstrate present state of the art features and capability.

Jan 1, 1978

By Charles W. Allen

The Athens mine is in the city of Negaunee, Mich. It is one of the larger producers of soft hematite ore on the Marquette iron range. The property is held under lease by the Athens Iron Mining Co., and is operated by the Cleveland-Cliffs Iron Co., which is a partner with Pickands, Mather & Co. in the Athens company. The mine was opened in 1913, and shipments of ore commenced in 1918, the total reaching 3,063,711 tons up to Jan. 1, 1932. Diamond-drilling from surface, together with a knowledge of geological conditions in neighboring properties, gave a comprehensive picture of the location, size and shape of the orebody before shaft-sinking started. Striking east and west, the orebody entered the east boundary of the property at a depth of about 1500 ft. below surface. A pitch of 15" to the west carried it down to about 2500 ft. on the west boundary, about double the depth of that of any soft-ore property heretofore worked on the Marquette Range. The width of ore averaged close to 500 ft., and the thickness 300 feet. The depth of the deposit and its size, together with an overburden of quicksand, which in places reached a thickness of 150 ft., presented unusual mining problems. The use of a caving system made surface drainage into the orebody inevitable, because the north boundary of the deposit was a vertical diorite dike 200 ft. wide, and the south boundary a northward-dipping impervious slate. S. R. Elliott, manager of the mining department of the Cleveland-Cliffs Iron Co., who was superintendent of the mine at that time, conceived the idea of starting at the bottom of the orebody and working upward, reversing the usual mining procedure. This innovation divided the Athens orebody into a series of steps, or blocks, the first of which was adjacent to the western boundary, and therefore in the lowest portion of the deposit. Top-slicing was to start under the capping in this first block by raising from the bottom level, and development and mining were to progress upward in successive blocks to the east. A complete description of the Athens system of mining was

Jan 1, 1934

By C. L. Horn

All the tunneling machines discussed in this chapter are Calweld machines. I have divided the machines designed for soft-to-medium formations into three groups, correlated with typical formations and estimated compressive strengths: 1) Running sand and silt requiring blade cutters. 2) Chalk and clay, requiring drag-type cutters, for compressive strengths ranging from 0 to 2000 psi. 3) Sandstones, hard clays, and limestones, requiring disk cutters, for compressive strengths ranging from 2000 to 20,000 psi. All of the soft-to-medium-formation machines are powered by electric hydraulic or diesel hydraulic pumps. The pumps in turn drive hydraulic motors for the torque reaction. The soft-to-medium-formation machines are enclosed in a 360º shield with a cutting shoe, a center portion of the shield housing the mechanical equipment, and a tail shield. Tunnel supports are usually required, and the supports are normally erected in the tail shield. Our first machine was built in 1963, and all but five of the machines illustrated in the figures with this chapter were built in 1966 and 1967. Some of the machines manufactured will be discussed in the following sections; specific features as development has progressed will be pointed out. HARD-ROCK MACHINE The Calweld hard-rock machine has been designed along basic and accepted principles for a hard-rock mechanical borer. The features of this machine are as follows: 1) Direct electric motor drive through a planetary gear reduction ring and pinion gear, and then to the cutting head through a hollow drive shaft.

Jan 1, 1970