Search Documents

By P. R. Sahm, T. V. Pruss, D. A. Gandolfo

Cb 3 Sn powders were hot-pressed to estahlish densi-fication conditions and assess the possible use of such compacts in multiphase structures with ceramic or magnetic inclusions. Superconducting transition temperatures, Tc, were measured as a function of powder particle size, pressing temperature, and second-phase admixtures. The highest transition temperatures were found in coarse powder (5 to 500 u) compacts and were only weakly depended on pressing temperatures up to 1200°C. Fine powders (below 5 p), however, both single-phase CbsSn and Cb3 Sn-composites, showed a stronger dependence on hot-pressing temperatures. While Al2 O3 phase admixtures did not affect T, much more, a Pronounced T, degradation was observed upon the addition of ferrimagnetic Fe2 Mno. 5 Zno.5 O4 powders. Likewise, critical current densities, Jc, at 4.2° K were lowered appreciably in the ferrite doped samples, whereas the neutral A1203 inclusiow gave slightly improved Jc values. MULTIPHASE structures in electronically active materials have recently gained in interest as pointed out by Galasso in a review article.' In superconductors the most widely reported group are eutectic alloys which have been mostly investigated with respect to the proximity effect.2"4 In addition, "artificial eu-tectics", for example in the form of mercury-vycor glass sponge5 or fine niobium wires imbedded in a copper matrix,= have been prepared to attain higher critical fields and critical current densities. The idea was to enhance flux pinning phenomena by second-phase inclusions or ho1es. 7 Flux pinning should also be possible by the introduction of insulator inclusions into a superconducting matrix. Ceramic-metal combinations are most easily produced by hot pressing (= pressure sintering), as it permits an almost unlimited selection of material combinations. Cb 3 Sn has been prepared by vapor phase growths or in the form of thin films. Large compacts must be sintered,1° however, and normally present difficulties. At temperatures below 1350°C insufficient densities are obtained and at higher temperatures the loss of tin due to dissociation upsets the stoichiometry. Hot pressing is a natural approach to circumvent the problems, since one can obtain satisfactory densities despite low sintering temperatures. This work was mostly concerned with establishing conditions to hot press Cb3 Sn and Cb3 Sn multiphase structures (= composites), because no data are presently available, and to evaluate these with respect to their transition temperatures. However, a few measurements on critical current densities were also carried out, in particular to assess the value of ferrimagnetic inclusions. I) EXPERIMENTAL PROCEDURE The experimental procedure involved the preparation of feed material and powders, hot pressing, and evaluation of the resulting ingots. As no attempts were made to synthesize Cb3Sn from the elements during hot pressing, feed material had to be produced. For this purpose, a stoichiometric Cb-Sn powder mixture was compacted into a 3-cm-diam ingot (80,000 psi) and then inserted into a quartz tube and evacuated. Rf heating was employed. Above the tin melting point (230°C) liquid tin was forced out of the ingot, but was pulled back by capillary action after approximately 0.5 hr of continuous pumping at 700°C. Thus, it appears that evacuation at this temperature caused desorption of impurity gas creating wetting surfaces which, later on, favored alloying at relatively low temperatures. After a presintering period of 17 hr at 800°C, the quartz tube was tipped off and sealed into another such larger-diameter tube which, in turn, was connected to a pump system. This configuration permitted a temperature treatment at 1400°C, carried out for 65 hr, without collapsing of the glass walls or unfavorable chemical interaction of Cb3Sn with the quartz. The resulting material was

Jan 1, 1969

By RAY J. CORFIELD

IN a previous paper, "Electric Shovel Operation at Utah Copper Mine," which was read before the Western Division of the American Mining Congress, the problem of electrifying a fleet of steam shovels was described. This paper deals with the electrification of the haulage system which, when completed, will make the mining operation completely electric, with the exception of drilling operations which will continue to be performed by air. The general layout of the haulage system involves the use of heavy curves in addition to heavy grades of between 4 and 5 per cent. In a mining operation of this kind no trackage can be called permanent; this complicates the overhead construction somewhat and makes it necessary to design special forms of trolley construction, some of which will be described in detail below.

Jan 1, 1929

By G. B. Walker

THE sink-float methods designated by heavy-media separation processes were pioneered by C. Erb Weunsch for the treatment of base metal ores as an improvement over jigs. The work of Weunsch was further developed by Victor Rakowsky and The American Zinc, Lead and Smelting Co. Early in the development of the processes, the inherent unsuitability of galena as the solid constituent of the medium was recognized and ferrous media amenable to magnetic recovery and control were developed. The high efficiency and low cost of magnetic recovery and cleaning of ferrous media regardless of particle size, slime contamination, or surfacial oxidation had led to the adoption of ferrous media by all of the sink-float plants operating under the heavy-media separation processes patents controlled by American Zinc, Lead and Smelting Co. Approximately 2,000,000 tons of base metal and nonmetallic minerals are treated each month by these methods.

Jan 1, 1949

By William P. Blake

THE phenomena of concentric arrangement of minerals in rock-masses, generally known as "orbicular structure," have of late received much attention from investigators. Lawson, of the University of California, has described the orbicular gabbro at Dehesa, San Diego county, Cal. Kessler and Hamilton, of Stanford University, working independently upon the same subject, published their descriptions,2 giving also a list of many other localities in Europe and America where orbicular rocks are found, adding copious references to the literature of the subject. The orbicular diorite of the type locality in Corsica., familiar to mineralogists and petrologists under the name "Napoleonite," was described by Vogelslang in 1862.3 Chrustschoff, of St. Petersburg, has also given much atten¬tion to the subject, and is the author of a classification of the various known forms of orbicular structure.4 No complete and satisfactory explanation of the origin of or¬bicular aggregations in rocks has yet been offered. The patent fact is generally recognized that the constituent minerals have crystallized from a more or less molten or plastic magma, but why these minerals should be arranged in concentric spheres or crusts has not been clearly shown. Vogelslang, for example,

Jul 1, 1905

By Jun-Yan Chen, Stefan H. Boshkov

Metal mining in the People's Republic of China has shown great growth during the last three decades. Over 150 new iron ore mines and nonferrous base metal mines have been opened since 1949, althouc.11 most of them of medium and small size. Concurrently, many old mines were enlarged and reconstructed. The production of iron ore has grown from less than 1.5 million tons per year in 1949 to almost 76 million tons in 1978. A corresponding increase in the total annual output in the nonferrous metal mineral industry has also been noted. It is well known that the PRC is very rich in metal mineral resources. The reserves of tungsten, tin, antimony, molybdenum and iron ore are ranked in the top three in the world. Recently, some copper porphyry ore deposits were discovered in Jianxi and Anhui provinces. Some large nickel-copper sulfide deposits were discovered and have been developed in North- West China. Huge iron ore deposits have been found in Liaoning, Hebei and Szechwan provinces. However, the bulk of the iron ores are low grade. The growing metal mineral production has met basic domestic needs since 1949; it has also proven China's big resource potential. Mining methods have also undergone development in the past 30 years. About 80% of the annual output of iron ore comes from open pits, whereas about 58% of nonferrous metal ores come from underground mines. Blasthole open stoping, sublevel caving and induced block caving are widely used in Chinese underground metal mines (table 1). This paper summarizes in detail the planning for and application of these three bulk mining methods in the nonferrous and iron ore mines in China. CLASSIFICATION OF UNDERGROUND MINING METHODS The main principle of the classification of underground mining methods in PRC is ground support in the stoping cycles of the mining blocks or stopes. Table 2 lists this classification. It is essentially the same as that given in the SME Mining Engineering Handbook. Be- cause pillar removal is a secondary mining operation, using a variety of methods, they are not included in this classification. As is the case with most classifications in science and technology, there is no precise division between the classes of mining methods. Because of the rapid development of consolidated filling techniques in the past twenty years, some types of open stoping methods use fill in order to improve the ground conditions for the secondary recovery stage. Thus, these mining methods have features of both methods using no artificial support and those using artificial support. In this classification, this type of mining method is placed in the latter category. The shrinkage stoping method has been employed extensively to mine steeply dipping narrow veins of tungsten and tin in the Jiangxi, Hunan, Guangdong and Guangxi provinces. Shrink- age stoping is placed under the class of mining methods without artificial support be- cause this reflects the nature of the Chinese experience. The function of the broken ore serving to support the footwall and/or hanging wall is limited, because the expectation is for the host rocks to remain unsupported until the stope is drawn empty. APPLICATION OF BULK MINING METHODS Bulk mining methods consist of blasthole open stoping, sublevel caving and block caving. These stoping methods have much in common, such as: bulk ore materials blasted by long holes; higher production rates of stopes or blocks and higher production efficiencies of the whole mining systems.

Jan 1, 1981

By E. M. Elkin, J. H. Schloen

All known methods of treating and recovering the various components of copper refinery slimes are discussed. The slimes treatment processes presently used by five copper refineries are described and flowsheets are given. A bibliography is appended. THE recent increase in anode copper production at the Noranda smelter placed an additional load on the Montreal East plant of Canadian Copper Refiners Limited. The consequent increase in the amount of anode slimes led to a careful consideration of the various methods of slimes treatment. A critical review of these methods is presented here in the belief that it would be of interest to copper refiners. No such review has yet been published, although a number of individual flowsheets have been described. To make the information of greater value, a questionnaire was sent to all copper refineries. While the overall response to the questionnaire was not entirely satisfactory, the foreign refiners gave much detail in their answers and expressed willingness to cooperate further if needed. Although the data below do not cover all refineries, it is thought that examples of all flowsheets currently in use are included. A comparison of these flowsheets should prove of interest. The paper is divided into two parts. One part deals with a discussion of all known methods of treating and recovering the various components of the slimes. The second describes the processes now in use at various copper refineries for the treatment of raw slimes up to the production of Doré bullion. A brief description of the two main electrolytic methods of parting Doré bullion is appended. Since the first commercial application of electrolytic refining of copper by J. B. Elkington in 1865, the treatment of anode mud or slimes has undergone many changes. The object of treating slimes has always been the recovery and separation of precious metals. With the passage of time, increasing attention has been paid to improvement in recovery and quality of byproducts, mainly selenium and tellurium. The original methods of treatment were crude, although relatively direct. For example," the slimes were fused on a dolomitic clay bed in a reverbera-tory furnace; the slag was removed and the resulting metal cupelled to silver and gold. In another process, the dried slimes were oxidized and scorified on the lead bath of a cupelling furnace. Later, these pyrometallurgical methods were modified by sulphuric acid leaching, followed by fusion with niter in a reverb eratory furnace. A preliminary oxidizing roast improved the leaching step. Straight hydro-metallurgy has not found practical application. No matter what method is employed, the result is Dorb metal—a silver-gold alloy, with or without the metals of the platinum group. Characteristics of the Slimes Anode slimes are made up of those components of the anodes which are not soluble in the electrolyte. They contain varying quantities of copper, silver, gold, sulphur, selenium, tellurium, lead, arsenic, antimony, nickel, iron, silica, etc. The color of raw slimes is grayish black and the particle size is —200 mesh. However, Baraboshkin and Gaev (Ref. 1, p. 37), describe light gray colored slimes from the electrolysis of secondary copper which are composed predominantly of sulphates and of basic salts. In anode furnace practice primary and secondary metals are not usually segregated and such slimes do not commonly occur. Copper in the slimes originates to a large extent in the cuprous oxide of the anodes and is therefore dependent on the oxygen content of the latter: Cu2O + H2SO4 + CuSO4 + H2O + Cu [I] Opinions have been expressed that some of the copper is formed by decomposition of cuprous to cupric sulphate Cu2SO4 ? CuSO4 + Cu PI The product of either reaction is very finely divided. Depending on the slimes composition, much of the copper is combined with sulphur, selenium, tellurium, etc. The balance of the copper is in the free metallic state.

Jan 1, 1951

By David R. Maneval, H. B. Charmbury

At the turn of the century, iron and coal were the keys to industrial prosperity. At that time, Pennsylvania was the leading mineral producer in the Country, producing 200,000,000 tons of coal in a typical post-World War I year. Close to 90% of the Nation's energy was generated by coal. Today, coal accounts for but 22% of the energy generated, leading to a drastic reduction in Pennsylvania coal output. In contrast with the post-World War I days, 1964 figures showed a drop in production to 93,846,480 net tons. This huge decrease has created a serious economic problem in a state so much dependent on the coal industry. Along with the reduction in coal production, employment has dropped considerably through these years (the number of miners alone has gone from 280,011 to 43,149), thus causing a heavy burden of supporting the unemployed on the taxpayers. As far back as 1939, coal operators and economists saw the problems on the horizon and the need for improvement. Realizing that research was a way to improve and stabilize the industry they demanded legislative action. The Legislature reciprocated with a small grant to The Pennsylvania State University with the provision that each State research dollar be backed with one from the industry. This initial grant laid the foundation for the further growth in coal research.

Jan 3, 1966

By D. S. Choi, H. von Schonfeldt, H. D. Dahl

The design of pillars around a longwall panel in which the effect of the adjacent and worked-out panel is taken into consideration is discussed. A mathematical model is used to duplicate field observations such as opening closure and pillar rib movement. The model is then used to predict the effect of changes in mining geometry on the opening stability.

Jan 1, 1976

By M. K. McCarter

Jan 1, 1985

By Alexander L. Holley

Jan 1, 1879

By R. A. Davidson, L. Silverman

RESIDENTS of many urban centers are becoming increasingly aware of the obscuring effect of fume and smoke discharge from power, metallurgical, chemical, and other industries; and they, as well as the legislatures of these affected cities, are agitating for cleaner air. Management's most pressing problem is to find an economical way to reduce process effluents in response to the growing pressure from population and legislative demands. The removal must be done, if possible, without handicap to the current operation, since the costs of relocating are often excessive or prohibitive. In fume recovery or disposal, an important item to consider is whether or not the material being discharged has any value. If it has commercial value, the cost of its recovery may offset or aid amortization. For this reason, in making a study of the specific problem in hand, a major factor was the nature of the material emanating from the stack: in particular, its particle size, size range, and its chemical and physical composition, as well as its potential value and utility when recovered (in either a wet or dry state). Should the product have no commercial value, it must be disposed of at minimum cost in a way to prevent recontamination. Initial studies were therefore made to determine stack concentrations and volumes of material evolved from the operations. The next phase of the study concerned the physical and chemical nature of the collected fume. The third portion of this paper describes the wet and dry collector studies undertaken to recover the fume. Cleaning Requirements for Ferroalloy Furnace Operation The basic need for any effluent collection equipment is the highest possible efficiency and the lowest tolerable resistance when the power consumption involved is considered. Since the electric furnace effluent is largely composed of fume of small size (less than 0.5u), it has high light obscuring properties, and even low concentrations will cause some loss of visibility and be evident to nearby residents. The permissible limit for fly ash emission in many cities is based on a weight value (viz, approximately 0.4 grains per cu ft), but the smoke density values are dependent upon a shade of color. In the case of the Los Angeles County code, emission is restricted to pounds per pound of material processed per hour basis (but not exceeding 40 lb per hr for any one given plant operation). If an average particle size of the fume from ferro-silicon alloy electric furnaces is assumed to be 0.4u (as shown later, this is the approximate mean size) and an average loading of 1 grain per cu ft (stp), each cubic foot of stack gas will contain approximately 75x10 10 particles (based on assumed, and confirmed, spherical shape and a standard deviation of unity). When it is realized that the air in metropolitan areas, which are also general industrial areas, contains approximately 5x108 particles, the tremendous light scattering effect of this concentration becomes apparent. Consequently, nearly 100 pct collection would be necessary to equal the average concentration. Fortunately, however, discharge from a high point above ground (50 to 100 ft) will result in at least a thousandfold dilution, or the stack concentration reaching the ground in the foregoing case might result in a ground concentration of ' particles. If the concentration at the source could be reduced by a factor of 100 (99 pct efficiency of collection), then a concentration of 75x10" particles would be diluted to 7.5x10' which would be very satisfactory. An efficiency of 90 pct (factor of 10 decontamination) at the source would result in a discharge of 75x109 articles which upon dilution yields 75x10 which is still 15 times the general air value. Another approach to this consideration is to use the value of concentration of 0.005 grains per cu ft for the value of a visible effluent as cited by Kayse.1 To attain this value with an average loading of 1 grain per cu ft would require an efficiency of 99.5 pct. Since the foregoing value is not based on any reported size of fume particles, it is felt that the numbers' approach given previously is more reliable. These calculations serve to indicate the desirability of thorough cleaning, preferably at the source, and with efficiencies well above 90 pct, preferably above 95 pct (dilution 1:20). One of the most important items in any control program is to reduce the concentrations as close to their sources as possible. The use of better furnace design, deeper coverage over the electrodes, and the prevention of blows or breaks in the surface all help to reduce dissemination; consequently, all of these improvements should be made, if possible, to cut down the effluent load. In addition, in order to minimize the volume of contaminated air that has to be cleaned, the furnace should be enclosed as much as possible. Test Arrangements Before fundamental studies with collectors were made, a furnace stack selected for the test program was sampled to determine the gas temperatures and

Jan 1, 1956

By James E. Hoffmann, John A. Bonucci, Peter D. Parker

A hydrometallurgical process has been developed for the recovery of high-purity silver from sulfated residues. The process eliminates the high temperature operations ordinarily associated with silver recovery and refining. The crux of the process is a metathetical leach which maintains the sulfate ion concentration at a level which both allows silver nitrate to be freely soluble and simultaneously depresses the solubility of lead nitrate. The subsequent hydrolytic purification of the silver nitrate solution, the recovery of high-purity silver by electrowinning in a diaphragm cell, and the final product purity are discussed.

Jan 1, 1981

By A. P. Svenningsen

DURING the work at the test mill in Morenci, it was determined that a suitable feed for the ball mills could be made by a single pass through a short-head cone crusher. These crushers did not require a closed circuit delivering only a screen product to the mills, such as is the practice in some concentrators. By no means does this mean that the practice in these other concentrators is wrong, but just that the Morenci ore can be most economically crushed and ground in this manner. Therefore, the design of the secondary crushing plant was simply a problem of taking 25,000 tons of ore per 16 hour day from the primary crusher, this ore ranging in size from fine particles to 10 or 12 in., and reducing it to minus 3/4 in. Inasmuch as outages must be contended with in any crushing plant, it was assumed that the crusher would operate at full capacity for approximately only twleve hours per day, which is three-quarter capacity for the 16-hour shift. With this in mind, it was necessary to design a crushing plant which would average approximately 1600 tones per hour for the 16-hour day, or 2000 tons per hour for slightly over 12 hours per day.

Jan 1, 1942

By Yasushi Ishikawa

The fact that the degree of granulation and the state of granulated particles of sinter raw mixtures are the influential factors in ensuring coke combustibility and permeability during sintering has been clarified. Based on this knowledge, Nippon Steel developed the divided coke-addition process and the technology to utilize binder, and applied them on a commercial scale. Productivity and sinter quality are thereby greatly improved with a significant reduction in fuel consumption.

Jan 1, 1977

By Gerald M. Friedman

CONVENTIONAL usage defines emery as a natural aggregate of corundum and magnetite. Because emery bodies contain abundant spinel two types are recognized, spinel-bearing and spinel- free. Watson and Steiger1 introduced the name spinellite for emery in which spinel is a major constituuent, but this term has not been generally adopted. Spinel emery grades locally into spinel magnetite rocks with or without accessory corundum. Even this variety has been used commercially in the past. The term emery therefore applies to natural aggregates composed of corundum and magnetite; corundum, magnetite, and spinel; and spinel and magnetite.

Jan 7, 1957

By Fritz F. Prugger, Peter R. Jones

This paper considers some of the main aspects of underground mining in the flat, rich, but deep lying deposits of Saskatchewan. It briefly describes the pertinent geological features as they relate to mining and the practical de-stressing techniques used to allow productive extraction in the high stress environment present in many of the province’s mines. Mining layouts, materials handling, and the evolution of some of the world's largest mining equipment are examined.

Jan 1, 1983

By J. D. Pelletier

SAN MANUEL orebody is a disseminated copper deposit in quartz monzonite, monzonite porphyry, and diabase. Quartz monzonite, which is Pre-Cambrian1 in age, is exposed in an area including No. 1 and No. 4 shafts and extending about 2400 ft southeast from No. 1 shaft. It is also exposed in the bottom of No. 2 shaft and in a zone roughly 500 to 1200 ft southeast of No. 2 shaft having its long dimension along a northeast-southwest axis. Churn drilling has shown all these exposures to be parts of a contiguous mass of quartz monzonite lying within and beneath the ore zone.

Jan 7, 1957

By William Hamilton Merritt

Since 1880 the occurrence of gold-ore has been known in the Lake of the Woods district. In 1879 the writer examined a so-called silver-location in the lake. More recent developments have extended, south and east, to the Rainy lake and along the Seine river, which flows from the northeast into the Rainy lake. The gold occurs in quartz-veins in the Huronian series. These Huronian rocks occur in belts in the Laurentian; the latter being the predominant formation in the eastern part of Ontario.

Jan 1, 1897

Jan 1, 1894

By Byron Pickard

AT MIDNIGHT of Sunday, Aug. 27, 1922, a fire was discovered in the main shaft of the Argonaut mine, Jackson, Cal. With the excep-tion of a shift boss and two skip tenders who escaped, the entire night shift of 47 men was trapped in the mine and entombed for 22 days, when the bodies were recovered. The entombed miners made a valiant but fruitless effort to save their lives. Rescue crews toiled strenu-ously day and night for 21 days to save the entombed men, only to find they had arrived too late. From the experiences of the entombed miners and of the rescue crews, valuable lessons may be learned to prevent future catastrophes.

Jan 11, 1922