Search Documents

By K. Unrug, G. Herget, A. Smith

SUMMARY Statistics on roof falls indicate that the cost of just removing the unwanted waste from roof falls in US coal mines amounts to about $20 M per year. Almost 40 percent of fatal accidents occur under permanently supported roofs, indicating that the assessment of roof stability is still a very difficult task. In an effort to obtain a better understanding of roof fall occurrences, rock strength and ground stresses were determined in the roof of one mine each in Western Kentucky, northern West Virginia, and Eastern Kentucky. Triaxial ground stress determinations clearly show that horizontal stresses were higher than vertical stresses, and that maximum stresses in the horizontal plane were concentrated between the NE-SW to E-W direction, with the exception of the Eastern Kentucky site which was above the drainage. Magnitudes of stress components may vary considerably in one drlll hole. Strength tests of roof strata materials were done on core samples. Mapping of roof falls showed that the geometry of an opening or maximum span were not the overruling factor because in the same general area, a roof fall was observed in a room (entry) which connected two stable four-way intersections. It should be noted that, in very wet areas, the roof can break up to the bed where water is carried, and a very low ratio between extent of roof fall to height of roof, fall is observed. Geometry is, however, a contributing factor because nearly 70 percent of roof falls are intersection falls. The frequency of fractures parallel to bedding in failed roof strata is much higher than that observed in the original strata, indicating a significant amount of working in the roof before failure.

Jan 1, 1984

By H. C. Johnson, J. K. Elliott

One of the primary requirements for successful operation of an enriched gas-drive project is to control the composition of injection gas. This can become a serious and difficult problem, particularly in cases where the enrichment material is being furnished from a number of field -produced gas streams. It is possible to effect control of the injection gas composition through frequent or continuous sampling; however, this can be extremely costly and, in many cases, impractical due to laboratory requirements of time. Another alternative would be to provide a calculation technique which would be flexible and sufficiently accurate to predict composition of the liquid and gas streams of interest at any point in the system. The purpose of this paper is to discuss a technique that was used successfully on an operating enriched gas-drive project for developing information which could be used for controlling composition of the injected gas. FIELD OPERATIONS The particular field (hereafter called Example field) in the example operation being discussed is composed of four oil reservoirs (A. B, C and E) and one gas condensate reservoir (D). Casinghead gas from the oil reservoirs and gas from the gas condensate reservoir are gathered through a field gathering system as shown in Fig. I for injection into Reservoir C. The gas mixture which is recovered from the five reservoirs for injection purposes is composed of gases liberated in 19 individual separators, each operating at a separate temperature and pressure. PROPOSED CALCULATION TECHNIQUE It is well known that vapor-liquid equilibrium calculations in general use throughout the petroleum industry can be used to predict reliably the phase behavior of hydrocarbon mixtures, particularly at pressures less than 1,000 psig. It is then a simple matter to account for the material on a ComPonent basis by m''ing flash and material balance calculations at each separation point in a hydrocarbon system. Accordingly, it was proposed to use vapor-liquid equilibrium and material balance cal- culations with a medium-sized electronic digital computer as a basis for developing a control procedure for use in controlling injection gas composition in the enriched gas-drive project. Although the approach is a simple one, the numerous vapor-liquid equilibrium calculations involved make the problem laborious; in this particular case, it would have been impractical to make sutficiently complete analysis without the aid of digital computing equipment. SAMPLING AND VERIFICATION OF CALCULATION PROCEDURE To obtain representative gas and liquid stream samples and to provide a quantitative measure of overall system Performance for comDarative purpLses, a thorough test of the field and plant system was conducted in the summer of 1957. Oil production at each battery was sta-

By K. E. Gray

The status of rock mechanics as applied to petroleum production might be termed, "Rock Mechanics-A New Name for Old Problems." The petroleum industry's efforts, from its earliest days, have been concerned with rocks, hopefully containing hydrocarbon accumulations in economic quantities. Geophysical and geological studies, wildcat and development drilling procedures, well bore mechanics and reservoir engineering operations, and certain aspects of production operations involve rock mechanics in various ways. Stress states and temperatures of interest range from low values in surface or near-surface activities, to very high values encountered at depths now exceeding 25,000 ft; deeper and deeper drilling will continue to increase this range. Time scales vary from a few microseconds in wave propagation measurements and some aspects of rock behavior during drilling, to seconds, minutes or hours for other drilling and well bore mechanics problems, to several years during which the efficient and economical depletion of reservoir systems is achieved. Subsurface sedimentary formations contain various fluids, of course, and reservoir fluid movement commonly involves three-dimensional, three-phase (oil, gas, and water) fluid flow. Many extremely difficult problems in rock mechanics arise for the Petroleum Engineer because of fluid movement (or lack of desired movement) in a well bore or reservoir. The discussion to follow illustrates just a few of the many topics in rock mechanics of significance to the petroleum industry. Time precludes anything other than a superficial treatment of the topics mentioned. A great deal of work has been carried out by various research groups in the petroleum field and significant efforts are continuing, as a review of the technical literature will reveal.

Jan 1, 1968

By Milton E. Wadsworth, J. Brent Hiskey

INTRODUCTION Fifteen years ago a distinguished electrochemist referred to electrochemistry as an "underdeveloped science " In the article in question, Professor Bockris (1) stated that many areas of.natura1 phenomena and applied technology are not perceived as being electrochemically based At that time, this was especially true for much of non-ferrous extractive metallurgy and was a particularly accurate description of hydrometallurgy During the last decade, there has been considerable advancement in applying the theory of electrochemistry to our know1 edge of hydrometallurgical processes and in understanding the mechanisms of underlying electrode reactions. Impressive as these advances are, there is still a growing need for electrochemical research of mineral systems and electrochemical engineering to apply this work in practical situations In a broad sense electrochemistry is defined as the physical chemistry of ions in solution and of phenomena which occur at the electrified interface. Bockris and Reddy (2) refer to electrochemistry as being divided into two fundamental domains, ionics and electrodics ionics is restricted to the behavior of ions in solutions, examples being many familiar redox processes Electrodics represents the main part of electrochemistry, and is the study of charged interfaces and the conditions governing charge transfer reactions across them. Considering hydrometallurgical applications, electrodics suggests the following relationship for a conducting solid (bulk or surface)

Jan 1, 1981

By T. H. Aldrich

(San Francisco Meeting, October, 1911.) THERE are two conditions generally prevailing upon the earth-those within atmospheric influence, tending towards oxidation, and those away from atmospheric influence, tending towards reduction. Practically all mineral substances from mines of any depth are in a reducing condition. Since the cyanide process, in order to dissolve silver or gold, requires that the prevailing conditions under which it operates shall be oxidizing, and the materials usually acted upon being of a reducing character, it becomes necessary to supply oxygen to the solution carrying the cyanide. This oxygen is usually supplied through the medium of dissolved air in the solution, or through the medium of various chemical compounds, which upon combining with the solution or the ore give off a part of their oxygen. Strange as it may seem, practically all mineral substances are partly soluble in water, especially water carrying alkali or cyanide. The greater the surface exposed and the finer the material is ground, the greater will be the rate of dissolving of the reducing agents from the ore into the cyanide solution. In most cases, if the solution carrying the ore particles is agitated with air, the air will dissolve into the solution faster than will the reducing-agents; but in some cases the reducing-agents will dissolve more rapidly on account of easy solubility or greater surface exposed. It is a dissolving race between the oxygen from the air and the reducing-agents from the ore, and if the reducing-agents predominate, cyanide will not dissolve the gold from the ore. In many cases it will dissolve some of the gold, because in a mass of irregular shape some of the gold particles might be exposed upon the outside surface of a particle of rock;' but if the solution had to penetrate through cracks, the side-walls of which were lined with reducing-agent-

Feb 1, 1912

By A. B. Kinzel

Precise knowledge regarding the effect of heat treatment on the properties of steel has made possible the detailed specifications and instructions covering optimum heat-treating temperatures and practices that are in current use. A distinct contrast is presented by the metallurgical treatment of steel adjacent to a fusion weld, as such steel is subjected to each temperature from room temperature to fusion temperature, and cooled at a rate that is not generally controllable but is predetermined by the nature of the assembly to be welded, the kind of welding used, and the surrounding conditions. This is true regardless of the type of fusion welding: oxyacetylene, electric arc, thermit or flash resistance. Therefore it seemed desirable to investigate the effect of this metallurgical treatment on the characteristics of carbon steels commonly used for welding, by a detailed study of metal subjected to each temperature range; i.e., each heat-affected zone. Oxyacetylene welding was chosen for the investigation because of the experimental facility of accurately segregating and studying each temperature zone. The nature of the zones produced by other types of welding is the same. The difference is primarily a matter of dimensions of each of the temperature zones involved. The advantages and disadvantages of the extent of the zone are of prime moment, and are discussed after the presentation of the detailed zone study. No mention is made of the fused metal proper, as this has been the subject of much published research and the nature of the solidified metal is fairly .ell known. General Method The scheme of procedure in the work herein reported involved the testing of the metal of each temperature zone adjacent to the weld in so

Jan 1, 1935

By Howard J. Smith

At the meeting of this Institute in February 1933,I presented a paper on potash development in southeastern New Mexico1, which contained a brief review of the Geological Survey's 20-year search for commercial sources of soluble potash minerals and of the events that led to the discovery, exploration, and first development of the deposits in that state. AS a more comprehensive review of the subject was published in December2, the present paper is intended only to discuss recent developments in the domestic potash industry, particularly in New Mexico. A summary of the findings of potash in the Permian Basin, by G. R. Mansfield and W. B. Lang, geologists of the United States Geological Survey, is now in process of publication by the University of Texas and will be omitted from this paper. In New Mexico prospecting for potassium salts during the past two years has increased materially the known area of commercial deposits; development has resulted in an increase from one to three in the number of shafts and the starting of a fourth; an increase of annual productive capacity to 1,000,000 tons of crude salts, or 250,000 tons of K2O; and an increase in annual refining capacity to 140,000 tons of muriate of 62.5 per cent grade. Construction has been completed to increase still further the production of high-grade salts. In California the American Potash & Chemical Co., operating on Searles Lake brines, has increased its plant capacity from about 100,000 tons to 180,000 tons of muriate a year and is now producing soda ash and salt cake in addition to potash and borax. Potash production from cement-plant and industrial-alcohol wastes remains unimportant.

Jan 1, 1938

By R. W. Raymond

[NoTE.—-This paper was presented at the Pittsburgh meeting in a partially completed form, and I fully expected to obtain, before the period of its publication, both the data and the leisure required for its completion. The hygiene of collieries was to have been separately considered, and the sanitary conditions of various metallurgical industries connected with mining were to receive an extended discussion, while at the same time the points treated in the paper as prosented at Pittsburgh were to have more ample illustration from American and European sources. Delay in obtaining expected information, and the continuous pressure of professional work, have prevented hitherto the execution of this plan ; and I can now publish only a portion of what I had designed to contribute to the subject. In the meantime this portion, but slightly changed, has been included as a chapter on the Hygiene of Metal Mines in a work entitled Hygiene and Public Health,, edited by Dr. A. H. Buck, of New York. An excellent chapter on the Hygiene of Coal Mines, contributed to the same work by Mr. Henry C. Sheafer, of Pottsville, affords me an opportunity to supply one of the deficiencies above alluded to. Mr. Shearer's chapter contains much material in the way of explanations not required by professional readers; And be moreover devotes a considerable space to the explosive gases, falls of roof, and other causes of accidents to life or limb—a branch of the subject not belonging strictly to bygiene. I therefore make extracts only from his treatise.—R. W. R ] It is convenient to divide mines, with reference to this subject, into two classes, collieries and metal-mines. Subterranean quarries, rock-salt mines, etc., present no conditions requiring them to be separated from the latter class.

Jan 1, 1880

By John T. Popp, Jodi A. Rulli, Anthony T. Iannacchione

Anomalous geological features in the coal and surrounding strata of a mine in northern West Virginia have fractured and deformed an inherently weak roof rock prior to mining. Horizontal stresses, as much as six times greater than overburden related horizontal stresses, have induced cutter roof failure. This failure was distinguishable from rock deformation associated with geological anomalies because it was induced by mining. The characterization of these features has allowed for the prediction of zones of unstable roof rock and the determination of failure trends on gateroad stability. Geological anomalies included clastic dikes and a narrow zone of sandstone roof. Clastic dikes, representing intrusions of shale and claystone, were invariably accompanied by local roof rock instability, and often formed the boundaries of roof falls. Shale was the dominant roof lithology except where a small sandstone occurred in the northwest portion of the longwall mining area. The sandstone occurs in two phases: a sandstone-filled channel, 5-m- thick and 60-m-wide, which eroded and replaced the shale roof and the upper part of the coalbed; and a sheet sandstone unit which was crossbedded to interbedded with the underlying shale. Horizontal stresses are naturally relieved through the initiation of cutter roof failure. This failure may extend from a few meters to several tens of meters horizontally, and from a few centimeters to several meters vertically. Orientations of entries and crosscuts has a greater influence on the direction and total length of cutter roof failure at the rib-roof intersection than does the principal directions of the in situ horizontal stresses. Seventy-four percent of the cutter roof failures occurred along the rib-roof intersection. Orientations of cutter roof failure away from the rib- roof intersection were clustered in the north-south direction and may have been influenced by the horizontal stress field.

Jan 1, 1984

By A. B. Kinzel

Precise knowledge regarding the effect of heat treatment on the properties of steel has made possible the detailed specifications and instructions covering optimum heat-treating temperatures and practices that are in current use. A distinct contrast is presented by the metallurgical treatment of steel adjacent to a fusion weld, as such steel is subjected to each temperature from room temperature to fusion temperature, and cooled at a rate that is not generally controllable but is predetermined by the nature of the assembly to be welded, the kind of welding used, and the surrounding conditions. This is true regardless of the type of fusion welding: oxyacetylene, electric arc, thermit or flash resistance. Therefore it seemed desirable to investigate the effect of this metallurgical treatment on the characteristics of carbon steels commonly used for welding, by a detailed study of metal subjected to each temperature range; i.e., each heat-affected zone. Oxyacetylene welding was chosen for the investigation because of the experimental facility of accurately segregating and studying each temperature zone. The nature of the zones produced by other types of welding is the same. The difference is primarily a matter of dimensions of each of the temperature zones involved. The advantages and disadvantages of the extent of the zone are of prime moment, and are discussed after the presentation of the detailed zone study. No mention is made of the fused metal proper, as this has been the subject of much published research and the nature of the solidified metal is fairly .ell known. General Method The scheme of procedure in the work herein reported involved the testing of the metal of each temperature zone adjacent to the weld in so

Jan 1, 1935

By Howard J. Smith

At the meeting of this Institute in February 1933,I presented a paper on potash development in southeastern New Mexico1, which contained a brief review of the Geological Survey's 20-year search for commercial sources of soluble potash minerals and of the events that led to the discovery, exploration, and first development of the deposits in that state. AS a more comprehensive review of the subject was published in December2, the present paper is intended only to discuss recent developments in the domestic potash industry, particularly in New Mexico. A summary of the findings of potash in the Permian Basin, by G. R. Mansfield and W. B. Lang, geologists of the United States Geological Survey, is now in process of publication by the University of Texas and will be omitted from this paper. In New Mexico prospecting for potassium salts during the past two years has increased materially the known area of commercial deposits; development has resulted in an increase from one to three in the number of shafts and the starting of a fourth; an increase of annual productive capacity to 1,000,000 tons of crude salts, or 250,000 tons of K2O; and an increase in annual refining capacity to 140,000 tons of muriate of 62.5 per cent grade. Construction has been completed to increase still further the production of high-grade salts. In California the American Potash & Chemical Co., operating on Searles Lake brines, has increased its plant capacity from about 100,000 tons to 180,000 tons of muriate a year and is now producing soda ash and salt cake in addition to potash and borax. Potash production from cement-plant and industrial-alcohol wastes remains unimportant.

Jan 1, 1938

By Daniel D. Pollock

The il'lott and Jones theory of thermoelectricity predicts that the absolute thermoelectric power of alloys of transition and noble metals should be a maximum when the concentration of the noble metal is approximately 55 to 60 at. pct. An examination of the emf of a series of relatively pure alloys of copper and nickel shows that the predicted maximum occurs at about 57 at. pct Cu. This excellent agreement with the theory is considered to substantiate the Mott and Jones theory of thermoelectricity for binary alloys of transition elements. This theory is extended to show that the emf behavior of dilute, ternary copper-nickel base alloys, which contain approsimately 60 pct Cu and 40 pct Ni, may be described in terms of a scattering mechanism. The scattering effect of a third element is demonstrated to be a function of its valence and its period in the periodic table. Small amounts of solute elements have additive scattering effects upon the emf of the Cu-Ni base. The Mott and Jones equation is modified to include this scattering parameter. This adaptation accurately describes the thermoelectric behavior of ternary and quaternary CLL-Ni base alloys. An empirical form of the modified Mott and Jones equation is derived which permits the calculation of thermoelectric power with an average error of less than 0.4 pct at 500 "C. CONSTANTAN has long been used as a thermocouple element. Its approximate composition varies from 50 pct Cu, 50 pct Ni to 65 pct Cu, 35 pct Ni. Small amounts of manganese, iron, and other elements have been used to modify the composition in order that the resultant emf vs platinum conforms to nationally accepted table. Adjustments of this type are made on a purely empirical basis. Constantan was originally made in Germany and was imported into this country for thermoelectric and electrical resistance purposes. During World War I, the supply of this material became seriously depleted. The work of Bash4 was done in this period in order to develop a satisfactory substitute for the imported material. Bash's empirical work on Cu-Ni alloys is still the basis for all commercial constantans made in this country. No reexamination of the electrical properties of this system has been made, despite the fact that it is now well known that Bash's alloys contained impurities which strongly affected their thermoelectric behavior.

Jan 1, 1962

By Carl F. Floe, Michael B. Bever

THE possibility that carbon may be soluble in copper to a limited extent has been recognized for over a century. The quantitative investigation of this problem, however, requires more sensitive techniques than have formerly been available. Three recent developments have made possible more accurate determinations: the vacuum-fusion method of analysis, the production of copper of high purity and the availability of high-purity refractories, particularly graphite. In addition to its obvious theoretical interest, the problem of carbon solubility in copper is of practical importance. In the production of copper and of high-copper alloys, carbonaceous covers are frequently used. If even minute amounts of carbon are dissolved, insoluble carbon oxide gases will be formed when such metals are poured under oxidizing conditions. A mechanism of this kind could well be one of the principal causes of gas porosity in casting copper-base products. REVIEW OF LITERATURE In 1823 Vivian1 raised the question as to whether copper by overpoling becomes "combined with a minute portion of carbon." Karsten2 asserted, in 1832, that carbon reduces the high-temperature strength of pure copper, so that when the carbon content has reached 0.2 per cent the metal will be brittle at a dark red heat. According to Karsten, carbon contents of o.05 per cent make it difficult to hot-work copper. He also reported that the specific gravity of copper is 8.8969 and that it increases to 8.92 58 if the copper is cemented with carbon and then melted. He emphasized the difficulty of determining analytically the small amounts of carbon present in copper. The metal was removed by wet methods and the residue considered as carbon. At Percy's request, Dick,3 in 1856, carried out various working tests on copper that had been in prolonged contact with carbon, and found that the working properties of the metal had not been affected. He also attempted to determine the presence of carbon analytically. In one experiment the copper was dissolved and the residue was fused with litharge, and in another essentially a combustion analysis was made on a copper sample. In a final experiment, a sample was dissolved and the residue subsequently subjected to a combustion analysis. Indications of as much as o.005 per cent carbon were found, but Dick considered his work inconclusive largely because of the possible interference of sulphur. Percy4 concluded, from Dick's experiments and from some experimental work of his own, that the solubility of carbon in copper had not been established with

Jan 1, 1945

By John F. Kendrick, Paul D. Cornelius

This paper is a progress report of a study the authors are making of the sucker-rod pump, considered as a vibrating system with one degree of freedom, with forced vibrations and with viscous damping. Dr. S. Timoshenko's formula is given, defining such a system. Each factor is considered in respect to the problem of operating sucker rods, and the zone is pointed out in which the mathematics do not apply to the sucker-rod pump, because of its variable mass. This general theory is interpreted in the light of nearly two years of testing wells in the field, and correlating the results of other tests. The motion of the pumping mechanism is a vibration. The string of sucker rods vibrates with a natural frequency. The motion of the plunger is the result of adding together these two vibrations, and is modified by a damping or friction factor. The controlling factor appears to be the ratio of the period of the natural vibration of the rod string to the period of the vibration of the pump. The first conclusion is that a definite value of this ratio, which is below resonance and is probably not greater than 0.5, should not be exceeded in order to assure satisfactory performance from the sucker rods. The second conclusion is that the component parts of the pumping equipment should be selected to give the smallest practical period of the natural vibration, and when this does not permit operation at a safe speed and give the required plunger displacement, a longer polished-rod stroke should be used. While the quantitative results are but rough approximations, the qualitative analysis of pumping problems on this basis promises to be of considerable value in diagnosing the cause of poor performance and prescribing suitable remedies. The trouble that results, whenever it becomes necessary to crowd the sucker-rod pump, to take potentials or to handle increasing volumes of water, is responsible for the belief that this type of pump is not equal to present day needs, and that it is only a question of time before some other pumping device will take its place. Of the troubles experienced, it is not surprising that the frequency of sucker-rod failures should

Jan 1, 1937

FEW whose good fortune it has been to gaze on the Utah Copper mine but will agree that it is one of the two or three most magnificent man-made spectacles in the world. Skyscrapered Manhattan Island perhaps is more inspiring; but there the effect is obtained by aggregating a thousand separate units. The Utah mine is a single thing- the biggest thing that men have made. By the end of 1931 there had been moved at Utah 222,000,000 cu. yd. of material, including ore and the waste rock that overlay it. This figure will be increased at an average rate of nearly 20,000,000 yd. per year. Excavations for the Panama Canal are estimated at 232,300,000 cu. yd., but the Canal is 50 miles long, and it is impossible to obtain a comprehensive view of the whole project at one time. The spectator, on the other hand, need only walk part way up the east slope of Bingham Canyon to see unfolded before him the whole panorama of the great copper mine. In the foreground is a huge pit bottomed for the time being 100 ft. below the normal floor of the canyon, which also is the elevation of the main railroad yard. Here from 500 to 800 standard steel railway cars, each of 80-ton capacity, are assembled daily to carry the ore to the concentrators. But the main part of the mine and that from which ore is now coming lies above this level. As can be seen in the accompanying photograph, a series of terraces or benches reaches to the top of the mountain that projects between the main branch of Bingham Canyon and Carr Fork. From bench A (the yard level) to bench W is a vertical distance of 1500 ft. In height the benches vary from 40 to 70 ft. and in width from 30 to 450 ft. The lower benches, as they skirt the mountain,

Jan 1, 1933

By J. B. Austin

MEASUREMENTS of the rate of decomposition of austenite at constant temperature are commonly represented by plotting the percentage trans-formed on linear coordinates against time on either a linear or a logarith-mic scale, a method that yields a curve that in shape resembles an integral sign (Fig. 1). A graph of this kind is not always convenient because extrapolation to the beginning or end of the transformation, or even inter-polation, may be uncertain unless there are a large number of observations, which seldom happens; furthermore, the degree of consistency of a set of measurements is difficult to judge from such a curve. It is desirable therefore to find some mode of plotting, or even better to find a standard variety of graph paper, that gives a straight line instead of the integral shape. The straight line has many advantages; the number of readings required to fix the position of the curve is greatly reduced, interpolation is easy and rapid, extrapolation can be carried out with greater confidence and, finally, the consistency of the measurements is readily estimated from the scatter of the points. The last advantage is particularly valu-able when the data are obtained by direct microscopic examination alone, because they are influenced by the skill of the observer in estimating the relative size of areas, possibly also by undetected inhomogeneity of the specimen. A search for ways of representing the observations as a straight line yielded two methods which are described in this paper. The paper also includes an account of some interesting relations brought to light in applying these methods to the available experimental data. Usually the best way to derive such a method of plotting is to base it on established principles of chemistry and physics, as has been done, for example, for the temperature variation of the equilibrium constant of a chemical reaction. But so little is known of the mechanism of the decom-position of austenite, and so little is available in the way of well established background for changes of this kind, that it is simpler to rely upon purely empirical means. The general plan therefore is to study existing data with a view to finding some function of the direct observations that will

Jan 1, 1938

By Robert E. Thurmond

DISCOVERY of a commercial ore deposit has resulted from a program emphasizing geophysical techniques and concentrating upon exploration of alluvial-covered areas. United Geophysical Co. selected these areas as offering the best possibility of success, for here the surface evidence of ore deposits has been hidden from the eyes of prospector and geologist alike. Pima mining district, Pima County, Arizona, was selected for initial exploration. The project was successful in that a commercial ore deposit was discovered and proved through drilling and extensive underground development. A limited region of activity was chosen and library research was begun on available economic and regional geological publications relating to the mining districts. Field reconnaissance of those districts which seemed to hold exploration possibilities provided a general picture and ascertained the existence of alluvial-covered areas of interest. At the conclusion of the reconnaissance trips all data obtained were compiled, and the district which seemed to present the best exploration possibilities was selected by statistical methods. The statistical summary was based on the following considerations: Geological Factors: 1—type of intrusive, P—presence of favorable host rocks, 3—apparent intensity of mineralization, and 4—presence of favorable structure in covered or unexplored areas. Economic Factors: 1—past production from district or mine; 2—size, shape, grade, and type of ore deposit in the district; 3—ease of acquiring mineral rights; and 4—general development facility. Exploration Favorability Factors: 1—results to be anticipated from geological methods alone; 2—application of geophysical methods, namely, topographic conditions, surface interference, depth-size relation, physical property contrasts as related to ores or controlling structural features; and 3—drilling factors. Admittedly, many of these, factors do not lend themselves to absolute evaluation, but relative evaluation, subject to inaccuracies of personal judgment, is always possible. A relative scale from 1 to 10 was established for every factor, representing varying degrees of favorability. For each district a numerical evaluation of each factor was established and a numerical total determined. The obvious advantage of this scheme is that a more concise summation can be presented by numerical means than can be achieved by descriptive means. After a district had been selected as favorable, the first step was to carry out more detailed geological and economic studies to narrow down the areas of interest. The second step was to compile all available geological data from publications and add to these data by mapping where necessary. Geological interpretation and projection of structural or other control into covered or unexplored areas was made whenever logical. To determine the possibilities of geophysical application and to select a geophysical method, physical property contrasts were related to mineral assemblages and/or structural control. If geophysics seemed applicable, trial profiles were run crossing the area normal to the strike and spaced

Jan 1, 1955

By G. D. Cremer, J. J. Cordiano

Aluminum powder is a well-known article of commerce and in various forms has been marketed widely for use in paint, for pyrotechnic purposes and for exothermic mixtures. For a number of reasons, however, aluminum powder has not been employed extensively in powder metallurgy, although a great many proposals along this line have been offered. Aluminum and alumiuum-alloy powders oxidize readily upon exposure to air and the thin film of oxide (or hydroxide) thus formed is highly refractory, in that ordinary gaseous reducing agents such as hydrogen or carbon monoxide do not reduce the oxide to metal at temperatures below the melting point of aluminum. It has been thought that the presence of these films of oxide on aluminum particles would interfere markedly in powder metallurgical work and a number of suggestions have been made, either for preventing the formation of the film through the production of the powders in inert or reducing atmospheres, or for the removal of the oxide by means of powerful reducing agents, including "nascent" or atomic hydrogen released from metal hydrides. A second and more serious difficulty in the use of aluminum and aluminum-alloy powders in powder metallurgy resides in the fact that during compression such powders tend to adhere or cold-weld to the die walls, thus interfering with the formation and ejection of a compact. A third difficulty, which has been encountered only with aluminum-alloy powders, is their hardness when compared with elemental aluminum. Certain of these powders are susceptible to age-hardening, which further hinders the formation of strong green compacts. These conditions are particularly true of atomized aluminum-alloy powders. Even in the annealed condition, plastic deformation of alloy powders under pressure is low when compared with unalloyed powders. This fact, coupled with the lower corrosion resistance of the alloy powders. is probably the significant factor in our failure to obtain strong sintered pieces. Methods of Puoducing the Powder Many methods have been proposed for manufacture of aluminum powder, only a few of which are used commercially. Several of the more important processes include: (I) atomization of the molten metal; (2) mechanical pulverization and other types of comminution; and (3) graining, in which molten aluminum is stirred during freezing. For pigment and certain pyrotechnic uses aluminum flake powder is desirable, because of its greater proportion of surface to volume; and large quantities of such material are made by a procedure that involves stamping or ball milling. In making flake intended for use as pigment,

Jan 1, 1943

By G. D. Cremer, J. J. Cordiano

Aluminum powder is a well-known article of commerce and in various forms has been marketed widely for use in paint, for pyrotechnic purposes and for exothermic mixtures. For a number of reasons, however, aluminum powder has not been employed extensively in powder metallurgy, although a great many proposals along this line have been offered. Aluminum and alumiuum-alloy powders oxidize readily upon exposure to air and the thin film of oxide (or hydroxide) thus formed is highly refractory, in that ordinary gaseous reducing agents such as hydrogen or carbon monoxide do not reduce the oxide to metal at temperatures below the melting point of aluminum. It has been thought that the presence of these films of oxide on aluminum particles would interfere markedly in powder metallurgical work and a number of suggestions have been made, either for preventing the formation of the film through the production of the powders in inert or reducing atmospheres, or for the removal of the oxide by means of powerful reducing agents, including "nascent" or atomic hydrogen released from metal hydrides. A second and more serious difficulty in the use of aluminum and aluminum-alloy powders in powder metallurgy resides in the fact that during compression such powders tend to adhere or cold-weld to the die walls, thus interfering with the formation and ejection of a compact. A third difficulty, which has been encountered only with aluminum-alloy powders, is their hardness when compared with elemental aluminum. Certain of these powders are susceptible to age-hardening, which further hinders the formation of strong green compacts. These conditions are particularly true of atomized aluminum-alloy powders. Even in the annealed condition, plastic deformation of alloy powders under pressure is low when compared with unalloyed powders. This fact, coupled with the lower corrosion resistance of the alloy powders. is probably the significant factor in our failure to obtain strong sintered pieces. Methods of Puoducing the Powder Many methods have been proposed for manufacture of aluminum powder, only a few of which are used commercially. Several of the more important processes include: (I) atomization of the molten metal; (2) mechanical pulverization and other types of comminution; and (3) graining, in which molten aluminum is stirred during freezing. For pigment and certain pyrotechnic uses aluminum flake powder is desirable, because of its greater proportion of surface to volume; and large quantities of such material are made by a procedure that involves stamping or ball milling. In making flake intended for use as pigment,

Jan 1, 1943

By M. A. Whiting, H. Kenyon Burch

One of the advantages presented by electric drive in many classes of work is the ease with which the electric motor can be controlled automatically. In a large number of cases certain features of the control are automatic—for example, the rate of acceleration may be limited automatically or the equipment may be stopped automatically at the limit of travel—but the equipment is started and ordinarily is stopped by hand. In other cases the motion of the machinery is utilized to start, control the speed, and stop the motor automatically, independently of any operator. A considerable proportion of the large mine hoists now in use have certain automatic features, particularly protective devices against overwinding, and, in some classes of electric hoists, devices for preventing excessive acceleration or retardation. The large automatic hoists discussed in this paper, however, are completely automatic, i.e., capable of making their trips without the presence of an operator at the control levers. According to circumstances, various advantages may be obtained . by automatic control, chief of which are decreased power consumption, increased precision and safety of operation, and decreased cost of attendance. The first step in the analysis of a prospective automatic mine hoist is to determine whether automatic operation is feasible at all. If men are to be hoisted, or levels changed, the attention of an operator is required for these purposes; but under some conditions it may be entirely practicable and advantageous to build the equipment so that, while provision is made for hoisting men or changing levels, ore can be hoisted automatically from any one level. If, however, an operator's attention is required every few minutes for changing levels, handling men or drills, or other work requiring hand control, it is obvious that automatic operation between times will not be of any practical benefit.

Jan 1, 1917