Search Documents

By H. I. Najarian

This paper is a companion piece to the description of the electrothermic process that begins on page 141. It will be confined to a brief story of the development. of the Weaton-Najarian vacuum condenserf at this plant, together with up-to-date design and operating data. The Josephtown smelter was designed primarily for production of zinc oxide. However, the development of a method for production of zinc metal had always been under consideration, and accordingly one of the original eight units of the elcctro-thermic furnaces built in 1930 was set up to produce metal. The design of this furnace was identical with that of the oxide furnaces except that in place of oxide tewels opening into oxide manifolds, conventional conical clay condensers—similar to condensers used in horizontal retort smelting—were installed around the periphery of the furnace and in several tiers vertically for condensing the zinc vapors. The early experimental work in trying to condense zinc out of the mixtures of zinc vapor and carbon monoxide gas from the electrothermic furnaces indicated that, while the gases from electrothermic smelting would condense in surface-type condensers, the formation of blue powder was excessive and condenser efficiency low. Furthermore, operating a large unit of electric furnace with several hundred small condensers, with attendant high labor cost and unfavorable operating conditions, did not appeal to us. We also realized that a single unit of surface condenser capable of condensing 12 torg tons of metal per day would be of huge dimensions and possibly difficult of control. So we took as our aim the development of a method whereby a single condenser unit of reasonable dimensions would condense zinc, in one step, from the large volume of gases that the electric furnaces produced. We set about searching for knowledge on zinc metallurgy and design of zinc condensers in particular. Our study of the prior art focused our attention on the oft-repeated statement by earlier experimenters, that the most efficient way to condense metallic vapors, such as zinc vapors, was to bring the vapors into "intimate contact" with molten metal; but the methods offered for securing this "intimate contact" in any practical manner left much to the imagination. We were handicapped by not having some-one on the Josephtown smelter staff who could lay claim to being an expert zinc metallurgist and could give guidance from actual experience on the practicability of various schemes that haunted our imagination. Laboratory Experiments However, we had an expert ex-steam engineer in the person of George I?. Weaton, manager of the Josephtown smelter, who had had long experience with steam-jet condensers and would reiterate his belief at every opportunity that the logical and the most efficient way to condense zinc would be with a jet-type condenser. We became intrigued by the possibilities of a zinc con-

Jan 1, 1944

By A. W. Gray

Page CRUSHING STRENGTH...................... 659 The Black Dynamometer....................659 A Standardized Procedure for Crushing Strength Tests...... 660 Influence of Height of Test-piece upon Apparent Strength ..... 662 Influence of Packing Pressure and of Packing Time........ 662 Application of the Logarithmic Law...............665 Influence of Amalgamation Variables.............. 665 Influence of Temperature................... 669 The Transition Region Near 70" C............... 671 Influence of Packing Pressure at Various Temperatures ...... 673 Influence of Age upon Alloy and Amalgam........... 676 DIMENSIONAL CHANGES DURING THE HARDENING OF AN AMALGAM .......................... 678 The Black Amalgam Micrometer............... 678 Thermostated Dilatometer Designed by the Author........ 681 Graphical Representation of Reaction Expansions......... 683 The Typical Reaction Expansion Curve ............. 684 Influence of Packing Pressure................. 686 Influence of Trituration Time................. 687 Influence of Temperature................... 688 Influence of Mercury-alloy Ratio................ 689 Influence of Packing Time................... 689 Influence of Annealing the Alloy................ 691 Influence of Size of Alloy Particles...............691 Extension of the Typical Expansion Curve........... 693 Influence of Thermal Softening and of Reamalgamating a Hardened Amalgam.......................... 634 Curves Obtained with a Variety of Dental Alloys ........ 694 Copper Amalgam ...................... 694 PRACTICAL APPLICATIONS OF THE RESULTS.......... 695 Phenomena which reveal chemical and physical processes that probably go on in many alloys at temperatures not far removed from their melting ranges are observable in dental amalgams. These amalgams should. therefore. be of even more interest to the metallographer, the metallurgistl the chemist. and the physicist than to the dentist who uses them for saving decaying teeth. For this reason I am here de-

Jan 1, 1919

By Zay Jeffries

THIS paper will include a brief discussion of Prof. Howe's paper on The Supposed Reversal of Inheritance of Ferrite Grain Size from that of Austenite.1 The general subject of grain refining in steel and iron will also be treated. The conclusions reached are stated in the following hypotheses which are discussed more in detail below. 1. The ferrite grain size in pure iron, the ferrite and pearlite grain size in hypoeutectoid steel, the pearlite grain size in eutectoid steel and the cementite and pearlite grain size of hypereutectoid steel are not inherited from the grain size of the mother austenite. 2. The only structural feature that is generally inherited from the austenite of hypo- and hypereutectoid steels on cooling through their transformation ranges is the position of the excess ferrite or cementite at the austenite grain boundaries, sometimes causing complete and sometimes incomplete networks which outline the old austenite grain boundaries. Rapid cooling through the transformation range will cause the non-inheritance of this structural (network) feature. 3. The austenite grain boundaries themselves are nearly always effaced in all steels and also in pure iron during the Ar transformations. 4. The grain-size refining of steel and iron is brought about by the combined. effect of non-inheritance of the transformation products on either heating or cooling, i.e., the austenite transformation .products do not inherit their grain size from the austenite on cooling through the transformation range for does austenite inherit its grain size from the products which form austenite on heating. 5. In general, in both iron and carbon steel the larger the austenite ,grain size, the larger will be the grain size of the transformation products on cooling. This, of course, assumes all other conditions constant except the austenite grain size. An exception is found to this general rule in very pure iron such as electrolytic iron. 1n this instance small austenite grains may form very large ferrite grains on cooling through Ar3.

Jan 11, 1917

By Robert S. Dewey

Drilling in West Texas during 1942 was substantially less than in the previous year. In all. 1267 Wells were drilled, as compared with 2325 wells in 1941. Of these 1267 wells, 1052 oil wells, 10 gas wells and 69 dry holes were drilled in proven fields and 36 oil wells, one gas well and 99 dry holes were wildcat operations. Of the 36 wildcat wells completed as oil producers, 16 led to new field discoveries, three found new productive horizons in old fields, and 17 extended the productive limits of established fields. Where semiwildcat drilling took place along established productive trends, there was often no sharp demarcation between wildcat wells that extend field limits and normal development to fulfil lease obligations, other than the arbitrary classification of a well as a wildcat if it was drilled at a distance of 2 miles from a producing oil well. The dry hole drilled on the edge of a field may have proved a more hazardous operation than a semiwildcat drilled several miles from production but favorably located on structure. The percentage of successful wildcatting ranges from 26.5 down to 14 per cent, dependent upon the degree of inclusion of the semiwildcat operations. Irrespective of which figure was used, the West Texas area maintained its better than average exploratory position. No doubt a number of factors may have influenced the extent of the 1942 development. Among those arising from the economic dislocation attendant on the war effort, the following are worthy of note. Owing to inductions into the armed forces and shipyard competition for mechanically trained men, experienced drilling personnel was sharply reduced, thereby increasing drilling costs and well-completion hazards. Replacement labor has not met the same standard of responsibility or workmanship to which the oil industry has grown accustomed. Increased military consumption of aviation gasoline and other crude products, coupled with decreased domestic consumption of lower-octane gasoline, has stimulated the market demand for the types of sweet crude most readily processed with available refinery equipment to meet war requirements, and has depressed the market demand for the sour West Texas crudes. As a majority of the purchasers of West Texas crude normally ship a substantial portion of sour crude to the refineries on the Atlantic seaboard, the loss and diversion of tanker service between Gulf Coast and north Atlantic ports have further curtailed the market demand for this type of crude oil. As some purchasers of crude oil were able to move by pipe line their West Texas trunk-line capacity to Midwestern refining centers, they were not impelled to curtail purchases of West Texas crude. The varying ability of the purchasers of crude oil to market West Texas crude was reflected back to various fields to which they were connected, causing an unequal distribution of production as among fields and operators. The pipe-line runs from the West Texas-New Mexico area decreased from approximately 354,000 bbl. Per day in January to about 265,000 bbl. in December 1942. .Approximately 2,991,000 bbl. of West

Jan 1, 1943

PRESIDENTS DAVID THOMAS 1871 Born November 3, 1794, Cadoxtan, Glamorganshire, South Wales. Died in 1882. Attended schools in Wales. Came to America in 1839. A.I.M.E.: Member, 1871; Honorary Member. Iron manufacturer; inventor. Built first anthracite fired hot-blast furnace in America. Known as the "Father of the Lehigh Valley." President, Catasauqua and Fogelsville Railroad; Director, Lehigh Valley Railroad; Founder, Thomas Iron Co. and St. Luke's Hospital at Bethlehem, Pa.; Trustee, Lafayette College.4 ROSSITER WORTHINGTON RAYMOND 1872-1874 Born April 27, 1840, Cincinnati, Ohio. Died in 1918. Brooklyn Polytechnic Institute, 1857; Lafayette College, Ph.D., 1868; Lehigh University, LL.D., 1906; University of Pittsburgh, Hon. LL.D., 1915., Gold Medal, Institution of Mining and Metallurgy (London). A.I.M.E.: Founder, Member of 1871; Vice President, 1871, 1876-1877; Secretary, 1884-1911; Secretary Emeritus, 1911-1918; Honorary Member. Consul¬ing mining engineer; practicing lawyer, sailor, soldier, writer, orator, editor, theologian, teacher, novelist, chess player. Recognized as the "Grand Old Man of the Institute." ALEXANDER LYMAN HOLI,EY 1875 Born July 20, 1832, Lakeville, Conn. Died in 1882. Brown University, 1853; Hon. LL.D., 1878. A.I.M.E.: Member, 1871; Vice President, 1874; Manager, 1877-1879. Bessemer Medal (Iron and Steel Institute, London), posthumously. Brought bessemer process to United States. A statue was erected in Washington Square in his memory and presented to the City of New York in 1889. The inscription notes: "foremost among those whose genius and energy established in America and improved throughout the world the manufacture of bessemer steel." ABRAM STEVENS HEWITT 1876 Born July 31, 1822, Haverstraw, N. Y. Died in 1903. Columbia University, 1842; Hon. LL.D., 1887. A.I.M.E.: Member, 1871; Manager, 1872-1875. Bessemer Medalist and Honorary Member, Iron and Steel Institute (London). Gold Medal, Chamber of Commerce of New York City. Philanthropist, lawyer, statesman, publicist, pioneer in the iron and steel industry. Mayor of New York City in 1887. Business partner of Peter Cooper, Executive Manager of Board of Trustees, Cooper Union, New York City.

Jan 1, 1947

By H. J. R. Way

THE work to be described was undertaken at various periods from 1937 to 1939 on the Busia gold field, in the eastern province of Uganda. It was decided to examine the possibility of reef prospection by the resistivity method, for it was not known how far the usually disintegrated nature of most reefs in the ubiquitous laterite near the surface would obscure indications obtained by resistivity traverses. The work at the commencement was therefore largely experimental, but the results obtained thereby were satisfactory, and a survey was started at the Government closed area at Amonikakine. With the limited time and resources at the writer's disposal, it was not possible to complete the survey to his satisfaction or to follow up exhaustively all the geophysical indications, but some of the results of the experimental work and the survey were of sufficient interest to be worth recording; in particular the relation between the width of reef, electrode separation and shape of the curve, and the interference effect of constant separation curves over zones of float are significant and useful. Three new veins were located, but only one contained sufficient gold to warrant detailed prospection. This was called the Geophysical reef, and was uncovered over a strike distance of 1140 ft., and there are indications that it extends over a distance of 1990 ft. These results and the recommendations consequent therefrom were embodied in a special report to the Uganda Geological Survey. HISTORY OF THE FIELD The Busia field is in the southeastern corner of Uganda near the Kenya-Uganda border, and is about 17 miles north of the northeastern corner of Lake Victoria. Gold was first discovered in the area in the stream beds by Davies1,2 in 1932. Subsequently numerous small alluvial claims were worked by prospectors and the area was prospected for reef by a company for periods varying from three to nine months, but was finally abandoned, as the results were considered unfavorable. Further prospecting by the Geological Survey in 1935-1936 under Davies3 and later under the writer4 uncovered three reefs with sufficient gold values to be of economic interest. These were finally taken over by a company known as Borderland Syndicate, which still owns the area, and from September 1937 to the end of 1941 about 13,000 oz. of gold was extracted from reefs of the area proved by the Geological Survey. Opencast mining operations are still proceeding (February 1943). The Amonikakine area lies to the immediate north of that of Borderland Syndicate. A certain amount of prospecting had been done when the writer started work there. As a result of his report, this area was taken over by another syndicate, but little further work was accomplished before it ceased operating because of difficulties of wartime working.

Jan 1, 1944

By Robert T. Hill

The successful completion, January 10,1901, by Capt. A. F. Lucas, of a well, near Beaumont, Texas, whereby an enormous flow, estimated at '75,000 barrels a day, was obtained, opened a new oil-field in the United States, kindled a frenzy of exploitation and speculation, revolutionized the fuel industry of a large region, and brought gain to thousands of people. Even to-day, it is impossible to cast up the present results or to prognosticate the future influence of this event. It has caused the revival of attention in other localities where oil had been suspected, and exploration for oil throughout the Texas region. It has attracted notice to the mineral resources of the Texas region, and created an interest in the geological conditions of that great State. This State, which has increased in population and wealth, as recorded by every succeeding census, with leaps and bounds such as are exhibited by no other part of the Union, now stands fifth in population and first in productive wealth per capita. Its fields, pastures, forests and mines teem with raw material. The whole economic evolution of the State has gravitated toward a focal point where these products were available for the coming of the kiln, the machine and the factory. The only drawback to the prosperity of the State was the lack of an economic fuel, inferior coal costing an average of $5.00 per ton at the time of the Beaumont discovery. This

Jan 1, 1903

By W. W. Lowry, G. C. Eggleston, W. E. Keck

THE potential iron ores of Michigan can be classified from the stand- point of the predominant impurities into siliceous, sulphurous and phosphorous ores. Research on the flotation of each of these classes of ore was carried out in the following manner. The flotative properties of the valuable minerals of iron and of the worthless and deleterious ones were first determined under carefully controlled conditions. This information was then applied to synthetic mixtures of these minerals, which simulated the potential ores. Finally, data obtained during the two foregoing stages of the investigation were used in the flotation beneficiation of samples of the potential ores. Hematite is the most important mineral of iron in each of the above classes of iron ores. This paper deals with a study of that mineral in the very nearly pure state. There are two varieties of the mineral-specular hematite and massive hematite. The latter is the principal variety, but the former is an important mineral of iron in some of the potential ores. Because of this condition, flotation research was performed with both varieties. This research consisted essentially of: (1) a survey of the literature on hematite flotation, (2) the preparation of pure massive hematite, (3) the preparation of pure specular hematite, (4) the development of a laboratory procedure and (5) flotation experimentation. For the purpose of this discussion, the results of previous work on the flotative properties of hematite can be summarized as follows: Specular hematite has been readily floated with terpineol and sodium oleate or heptylic acid1. Further, hematite has been likewise floated with a proprietary frother and oleic acid or other soluble oils2. Finally, lead nitrate, copper sulphate, silver nitrate, chromium nitrate, mercuric chloride, ferric

Jan 1, 1937

By Raymond B. Ladoo

Abrasives include the substances, natural or artificial, that are used to grind, polish, abrade, scour, clean or otherwise remove solid material, usually by rubbing action but also by impact (sandblasting, for example). They do not include abrasive tools-for instance, lathe tools and files-or polishing agents such as waxes, which act by filling pores. Detergents and cleaners whose action is chemical rather than physical are omitted although some chemical-action polishes and cleaners may also contain solid abrasives; for example, many automobile and metal polishes. General Considerations The most important physical properties of materials that qualify them for use as abrasives are hardness, toughness (or brittleness), grain shape and size, character of fracture or cleavage, purity or uniformity. For making bonded grain abrasives such as grinding wheels, additional important factors are stability under high heat and bonding characteristics of grain surfaces. The economic factors of cost and availability are always important. No one single property is paramount for any use. For some uses extreme hardness and toughness are needed, as in diamonds for drill bits; for others, the factors of greatest importance are hardness and ability to break down slowly under use, to develop fresh cutting edges when grains become worn-for example, in garnet for sandpaper, neither highly cleavable or friable grains nor extremely tough grains are wanted. For still other uses, great hardness is objectionable; for example, abrasives for dentifrices and for glass-cleaning soaps. For the most efficient use in the more critical applications, the different types of abrasives are rarely completely interchangeable; thus, while crushed quartz and garnet are both used in sandpaper, the papers are not at all interchangeable in their use applications. In the last analysis, the choice of a high-grade abrasive depends upon the quality and quantity of work done by the abrasive per unit of cost. Initial cost of an artificial abrasive. may be much greater than that of a natural abrasive but the artificial abrasive may do so much better work than the natural one, and do it so much faster, that the ultimate cost will be less. It is on this basis that artificial abrasives have largely replaced natural abrasives for grinding metal. Classification Abrasives may be divided into two general classes, natural and manufactured. The former includes all rocks and minerals used for abrasive purposes without chemical or physical change other than crushing, shaping or bonding into suitable forms. Manufactured or artificial abrasives are made either by heat or chemical action from metals or mineral raw materials. On page 2 is a list of the most important abrasives, classified as to inherent types and as to forms in which they are used industrially. For most types of use there are manufactured products that can be substituted for the natural products, usually at higher initial

Jan 1, 1960

By J. R. Dawson, A. B. Kinzel

THE purpose of testing is to determine whether the material in question is identical in all essential respects with similar material which has given satisfactory service. The most common method of securing such information is to select samples as representative of the entire material and subject them to destructive tests. As the welding industry grew, service data were accumulated and tests of welds took on new significance. New tests were devised and old tests modified so as to be more pertinent to welding. Moreover, in some cases the generally accepted procedure of testing by sampling is not accorded the same degree of confidence when applied to welds as in the usual applications. Thus, in instances where great hazard would be involved should the material fail, means of non-destructive testing have been sought with favorable results. Accordingly, tests used today may be divided into two groups, destructive and non-destructive tests.

Jan 1, 1930

By Jeffrey L. Thompson, Kenneth A. Gutschick, Robert C. Freas, Robert S. Boynton

Lime, the "versatile chemical," is, generally speaking, a calcined or burned form of limestone commonly known as quicklime, calcium oxide or calcia, or, when water is added, calcium hydroxide or slaked lime. Almost 40 different lime products are available, a fact which has contributed to the rather loose use of the term lime as well as to much confusion and misunderstanding. The term is frequently, albeit erroneously, used to denote almost any kind of calcareous material or finely ground form of limestone or dolomite. Lime is usually made from high-calcium or high-magnesium limestone, generally having a minimum of 97% combined carbonate content. Normally, high-calcium limes contain less than 5% MgO. When the lime is produced from a high-magnesium limestone, the product is referred to as dolomitic lime. Calcination, or the production of lime, has its origins in the earliest days of alchemy, with the general reaction class having been identified in an Arabic text printed in 1000 A.D. It was much later, however, in the mid-1700s to the mid-1800s before this basic reaction became understood from a scientific perspective. The production of lime has been so basic and simple that its underlying scientific principles have over the years received only intermittent investigation. Rather, much of the thought and inquiry has been directed toward the development of kilns. Thus, it has only been in the last 15 to 20 years that lime has received any concentrated scientific investigation relative to the thermodynamics and kinetics of the calcination and hydration reactions. Calcination refers to a broad class of reactions, of which the lime/limestone reaction is just one, wherein a substance is heated to less than its melting point, resulting in a weight gain or weight loss. In the calcination of limestone to produce lime, the basic chemical reaction is as follows: [CaCO3 (limestone) + heat (1000° to 1300°C)= 100 CaO (quicklime) + CO2 T 5644 or CaCO3 • MgCO3 (limestone) 10084 + heat (900°C to 1200°C) CaO • MgO (quicklime) + 2CO2 T 56 4088] While there is nearly universal agreement about the equilibrium conditions related to the limestone/lime reaction above, there have been numerous and varied calcination models developed for the reaction. Recent investigations have resulted in the development of the model shown in Fig. 1. From this model it can be seen that calcination is a function of both temperature and CO2 pressure. It does not, however, provide any indication of the rate at which the reaction takes place. Calcination is strongly time variant with different limestones. In a very broad sense this relates to the fact that the calcination reaction starts on the exterior surface of the limestone and then proceeds toward the center. As the calcination reaction takes place, the CO2 released at the reaction interface must make its way through the lime to the exterior surface. Therefore, because calcination is limited by gas diffusion to the surface of the partially calcined limestone, natural impurities in the stone, differences in crystallinity, grain boundary chemistry, density variations, and imperfections in the atomic lattice all play a significant role in

Jan 1, 1983

By M. C. Udy, C. H. Lorig

THROUGH the years much interest has been centered in attempting to develop a direct method of iron-ore reduction, to replace or supplement the present indirect blast-furnace process. It would not be difficult to produce a list of more than 500 patents dealing with the direct production of iron and steel, but the few of this type of process that have proved successful do not produce in competition with the blast furnace; they produce special products. A survey of the literature reveals that the equilibrium conditions for the reduction reactions (iron oxides with carbon monoxide and with hydrogen) have been fairly well established but that data on the rate of reaction are discordant, although the general effects of the variables are known. This dissertation deals with the rate of reduction of a magnetite concentrate with hydrogen. The following variables have been studied: bed depth, gas velocity, particle size and temperature. The behavior of a single particle was also studied. LITERATURE Two general factors should he considered in a study of reduction of iron oxide: (1) equilibrium relations, and (2) rate of reaction. The first factor, equilibrium, has received the attention of many investigators and the equilibria Fe3O4-FeO-H2-H2O, Fe304-FeO-CO-CO2, FeO-Fe-H2-H2O, FeO-Fe-CO-CO2 are fairly well established. Of the second factor, the rate of reaction, much less is known. Data are comparatively scarce and there is very little concordance. The discordance probably results from the large number of variables influencing the reactions. However, the general effect of the variables is known. Among these variables are temperature, gas velocity, particle size, porosity, gas composition (distance from equilibrium), presence of impurities, greater or less prevalence of side reactions, and even design of the apparatus itself. Wetherill and Furnas1 published an excellent paper in 1934. They point out that any one or more of five processes (the chemical reaction, diffusion of the reactant through the gas film, diffusion of the reactant through the solid phase, diffusion of the reaction product through the solid phase, or diffusion of the reaction product through the gas film) may be the slow process, and thus the rate-controlling process. It is regretted that the work of these authors was limited to experiments at one temperature, and that the range of gas compositions was limited. Langmuir2 has shown that heterogeneous reactions take place at phase boundaries.

Jan 1, 1942

By Will H. Coghill, P. H. Delano, G. D. Coe

DATA concerning the actual net energy required for pulverizing coal are lacking from the literature on coal pulverization. Power data given in the literature concern gross power and frequently include the power expended on the air blast or product-conveyor system, as well as power lost through friction in the pulverizer itself. Consequently, such data supply no information regarding the net energy consumed in pulverizing or the relative grinding resistance of various coals. In the study of coal pulverizing much work has been done on what is known as "grindability-index numbers," but grindability tests have seldom considered the energy input (that is, the "cause" part of the system "cause and effect"). There are many records of the effect, but even these have questionable value because the "grindability" tests did not make a pulverized product by a method comparable with commercial pulverizers. In many of the tests, only a selected part of the coal was ground, and the remainder continued to be an unknown factor. Furthermore, none of the grindability tests provide the balanced circulating load common to all modern commercial pulverizing. In order to obtain better understanding of the fundamental principles of coal pulverizing, the Bureau of Mines is investigating the "cause" phase; that is, the net energy input or net power excluding friction between the moving parts of the machine. As a first step in the investigation, it was necessary to design and construct a laboratory machine in which no friction-loss corrections are involved, which could grind and finish a minus-3/4 -inch feed, which could be emptied rapidly and completely, which could operate with a continuous feed and finish in an air separator; and, most essential of all, which would be equipped with a measuring device for recording only that portion of the total power consumed in actual pulverizing, hereafter referred to as "net energy input" or "net horse-powerhours." The channel-roller pulverizer here-inafter described is believed to meet these requirements. HISTORY OF THE MACHINE The work started when Ralph W. Smith, engineer, St. Genevieve Lime Co., St. Genevieve, Mo., was appointed one of the consultants of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama, to develop a machine for testing the abrasiveness of coal. Smith had already developed a machine for testing the abrasiveness of dentifrices,1 and it was thought the same principles might be applied to coal. Smith's machine had a revolving disk with an annular channel in which the sample was placed. Riding in the channel was a small block or runner of selected soft metal held

Jan 1, 1942

By M. L. Holzworth, Joseph C. Kremer, Paul A. Beck, L. J. Demer

FOR alloys which are in practice heat treated to obtain increased strength, such as steels, duralumin, copper-beryllium, and others, the treatment usually involves heating to a relatively high temperature. At such temperatures the grain size of the product is largely determined by grain growth. Even in metals and alloys annealed merely to relieve work hardening, recrystallization is generally followed by a certain amount of grain growth. Thus, effective grain size control, which is often of great practical importance in manufacturing processes, depends on the grain growth behavior of the material used. Despite its importance, grain growth has been the subject of few investigations of a fundamental nature. The term "grain growth" has been used to designate a group of related, but distinctly different, phenomena. The two most important and best known of this group are illustrated by the following example. Curve a in Fig r shows the increase of the average grain size of a copper-beryllium alloy, containing 2 pct Be and 0.15 pct Co, with increasing annealing temperature. The time of annealing was 2 hrs. The grain size was quite uniform in all specimens. The results of a similar experiment with an alloy containing 2 pct Be and 0.31 pct Co are shown by curve b. It is seen that for any annealing temperature below T. the grain size was smaller than in the previous case. Grain growth became slower with the higher Co content. This "inhibiting" effect of the higher Co addition was associated with the appearance in the microstructure of fine, light blue particles of the CoBe phase. Up to temperature T. the structure of the inhibited alloy (curve b) was just as uniform as the structures represented by curve a. However, after annealing at T, or at higher temperatures, the inhibited alloy showed some extremely large grains (much larger than the grain sizes developed by the uninhibited alloy with low Co content) mixed with the small grains according to curve b. The presence of these mixed or "duplex" structures is indicated in Fig 11 by the vertical lines branching off curve b. The type of grain growth occurring in uninhibited Cu-Be alloys (curve a) has has been most frequently and best investigated in brass. This type has been designated as "normal grain growth," while the grain growth phenomena occurring in inhibited materials were, at times, referred to as "abnormal grain growth." However, since the latter term has been applied occasionally to the phenomenon of critical recrystallization, which also results in large grains although by an entirely different mechanism, in the present paper a different nomenclature has been adopted in order to avoid confusion. Typical of the grain growth in uninhibited metals and alloys is the continuous

Jan 1, 1947

By P. F. Kinyoun

MANY interesting new features are embodied in the latest extension to the open-hearth department of the Bethlehem Steel Co., at Lackawanna, N. Y. Automatic control of the important factors in furnace operation-fuel, air, draft, pressure, slag composition, and of the temperature in various regions of the furnace-has been carried out to a remarkable degree; the human factor is minimized, and the chances for mishaps and irregularities in operation are greatly reduced.

Jan 1, 1937

By J. A. Fellows, Earnshaw Cook, H. S. Avery

THE increased use of heat-resistant alloys (26 per cent Cr, 12 per cent Ni, 16 per cent Cr, 35 per cent Ni, 12 per cent Cr, 60 per cent Ni, etc ) in recent years has been accompanied by continued demands by the consumer for improvement in properties The manufacturers of these materials, of necessity, have resorted to more critical studies of the basic causes of variations in fundamental properties To keep pace with the need for augmented information, previous techniques of investigation have been refined and new test methods and instruments created It is the purpose of this paper to describe the apparatus, experimental technique and precision of measurement that were employed in the exploration of properties of heat-resistant alloy presented in a companion paper† The detailed precautions in experimental procedure essential for attainment of accurate and comparable data at elevated temperatures cannot be too highly emphasized THE CREEP TEST Since the fundamental concepts of creep testing have been recognized for the past 20 years, present interest is restricted to refinements in equipment and experimental procedure The creep-test laboratory constructed for the American Brake Shoe and Foundry Co is designed to permit 1000-hr tests in the temperature range of 1200° to 2200°F with a choice of applied stress extending from 50 to 50,000 lb per sq in in increments of 50 lb per sq in To simplify the calculation of weight combinations, the loading beams (Fig I) are provided with counterweights to eliminate the tare The precision of the knife-edges (10 1 ratio) is such that a 10-gram weight placed on the upper specimen grip will be exactly balanced by a 1-gram weight attached to the loading shackle Check of the loading weights proved the maximum error to be 0 06 per cent Axial alignment is provided by crossed knife-edges in the grip seats The furnaces are similar in design to those of Crane and Company, Battelle Memorial Institute, and the U S Steel Corporation An 80 per cent Pt, 20 per cent Rh No 19 B and S gauge wire is used as the heating element The details of construction are shown in the radiograph reproduced in Fig 2 The windings are held in place on an alundum tube with alundum cement, the distribution of turns is adjusted to give a maximum temperature gradient of ± 1°F over a 4-in gauge length (Fig 3) To avoid sharp temperature differentials at the ends of the test section, the length of the furnace is four times the gauge length Sixteen-inch coupons are used to reduce the temperature of the threaded

Jan 1, 1942

By L. L. Handy

The development of a theory for miscible liquid displacement requires evaluation of the variables which affect growth of the mixing zone between solvent and displaced oil. Factors which appear to be important are individual fluid viscosities, viscosity ratios, flood rate, fluid densities, flow characteristics of the porous medium and molecular diffusion coefficients of the fluid components. The primary purpose of this paper is to evaluate diffusion effects. Theoretical treatments to date have been limited to floods for which the viscosity ratio is one. Two principal theories have been proposed. Von Rosenberg adapted for porous media a theory derived for capillary tubes by G. Taylor.' ,' In this theory molecular diffusion perpendicular to the direction of flow is a primary factor in sharpening the flood front. Slow floods give sharper fronts for a given distance traveled than fast floods. An alternative theory considers miscible liquid displacement as a statistical problem.3,4,5 Diffusion is not an important factor in this theory, but it leads to the same general type of equation as von Rosenberg's. Both theories predict S-shaped concentration profiles with the same dependence on distance traveled. The statistical or "dispersion" theory predicts rate independence, however. To supplement rate studies a direct measurement of a diffusion effect would be helpful in evaluating which of the two proposed mechanisms best describes miscible liquid displacement for one-to-one viscosity ratio systems. No quantitative theory has been proposed for floods in which a low-viscosity fluid displaces a high-viscosity fluid. It might be anticipated, however, that the extensive fingering observed in floods with adverse viscosity ratios would increase opportunities for an exchange of components between displaced and displacing liquids by a diffusional process. Even if molecular diffusion were not an important mixing mechanism for one-to-one viscosity ratio systems, it could be significant in systems with adverse viscosity ratios. METHOD FOR EVALUATING DIFFUSIONAL MIXING In solvent flooding the displacing liquid can become mixed with the displaced liquid by a number of processes; in general, either mechanical or diffusional in character. To evaluate the contribution of diffusion, a method was sought that would distinguish diffusional mixing from mechanical mixing. Suppose two soluble tracers are added to the displacing liquid and that one tracer has a diffusion coefficient much greater than the other. Then, if diffusion is important during miscible liquid displacement and if diffusional transport is primarily transverse to the direction of flow, substances with high diffusion coefficients will have sharper concentration profiles than those with comparatively low molecular diffusion coefficients. In order to have material balance the profiles for the two tracers must intersect. For one-to-one viscosity ratios the intersection would occur at the 50 per cent concentration point. It is generally assumed that diffusion in the direction of flow is negligible. This assumption appears reasonable because flow velocities are ordinarily orders of magnitude greater than diffusional velocities. If this is not a valid assumption, however, the shapes of the fronts will be further degraded by longitudinal diffusion. The effects of rate and molecular diffusion coefficients are the opposite for longitudinal diffusion to those for lateral diffusion. Higher rates or lower diffusion coefficients would tend to give sharper fronts. The double tracer method offers several unique advantages in evaluating effect of molecular diffusion. First, the method gives a direct measure of the effect of diffusion on mixing zone size. Second, the effect of a difference in diffusion coefficients is determined from a single experiment. Comparison of several experiments at different rates is not required. Third, the method is applicable for any viscosity ratio. Fourth, the method is unaffected by density differences between the two fluids which might result in rate dependent gravity effects. EXPERIMENTAL PROCEDURE Suitable tracers are substances whose diffusion coefficients differ as widely as possible, but whose adsorptions on rock surfaces is negligible. The two tracers selected were methanol and sucrose in water solutions. The approximate diffusion coefficients for methanol and sucrose, as given in the International Critical Tables, are 1.3 X 10-5 and 0.3 X 10-5 m2/sec, respectively. Concentrations in the water solutions were 200 gm/liter of solution for both methanol and sucrose. These high

By M. N. Dunlap

Tries article summarizes the successful incorporation of a flash-flooding stream into the tailing-disposal system at the St. Joseph Lead Company's Federal Division mill, in St. Francois County, Missouri. The mill was built in 1906, by the Federal Lead Co., as its No. 3 mill for the concentration of southeastern Missouri lead ores, and damming Davis Creek was first considered in 1908. Plans were made also in 1925 and in 1937. Dam layouts varied from a reinforced concrete structure to a barrier built of tailings alone. All were abandoned because of liability that would be incurred by flashflood rupturing of an incompleted dam. By 1942 mill capacity had reached 12,000 tons daily and increasing tailing-disposal costs again focused attention on the Davis Creek basin. This time the problem of riskless dam building was solved. Moreover, most of the items that appeared in the answer were materials that normally required wasting and the major portion of labor involved performed functions that it would normally have done, without constructive benefit, elsewhere. The new layout also made possible advantageous changes in mill-water supply pumping; static head being reduced from 514 ft to 95 ft, friction head from 4900 ft to 2860 ft, and pumping can be done now at periods of low power demand. The following facts about the Davis Creek watershed explain the 36-year reluctance to reach these, and other, benefits. Size: 3600 acres. Outline: roughly pear-shaped, 2 1/2 by 3 miles at the largest dimensions. Topography: mostly hill land with steep valleys. Relief : 760 minimum to 1153 maximum. Maximum rainfall: 3.36 in. per hour. Permanent water: none natural. Now 2200 gpm discharged through 16-in. drill hole from mine pumps underground. Geology: the 17 acres near dam centerline is Bonne Terre dolomite covered with sand and gravel eroded from Pleistocene beds that cap some of the hills. The remainder of the pond basin is on Davis shale. Soil cover: mostly second-growth timber with some abandoned fields; all subject to careless burning, which reduces water-retaining ability. Flood history: flash-flooding that had taken at least one life. Downstream values: two railroad bridges before creek intersection with Flat River. Immediately below confluence, a highway bridge, a low-water crossing, a few business establishments and several blocks of residences. In July 1942 the following segments of an ingenious plan were put into operation. A ditch 270 ft long, 16 ft wide and 5 1/2 ft deep was excavated to bedrock in the gravelly soil along the proposed dam's centerline. This excavation, which exposed many gravel-filled channels, was run full of slimes drawn from a riser set in the top of an adjacent tailings-disposal

Jan 1, 1947

By J. N. Chew, C. A. Connally

A correlation is presented for predicting the viscosity of gas-saturated crude oils under reservoir conditions. It is based on the dead oil viscosity and the solution GOR. The correlation was developed from a study which showed that at a fixed solution GOR, the relation between the gas-saturated oil viscosities and the correrponding dead oil viscosities is a straight line on logarithmic coordinates. Data from 457 crude oil samples from the major producing areas of the U. S., Canada and South America were used. The best straight lines through the data were fitted by the method of least squares with a digital computer. The correlation is presented in the form of an equation and also in a convenient gra-phical form. INTRODUCTION The viscosity of gas-saturated crude oils under reservoir conditions is an important physical property used in reservoir engineering calculations. Many difficulties are inherent in the sampling of gas-saturated oils and in the laboratory measurement of their viscosities. Therefore, it is frequently neither possible nor convenient to obtain measured values, so the viscosity must be estimated from other, more readily available data. This paper presents a correlation for predicting the viscosity of gas-saturated crude oils. The correlation is based on the amount of gas in solution and the viscosity of the dead oil at the temperature of interest. A previous correlation of these variables was presented by Beal. In comparison, the correlation presented here extends to a higher GOR and to a lower dead oil viscosity. Over the range of variables covered by both, this correlation is based on approximately 11 times as many oil samples. DEVELOPMENT OF CORRELATION A study was made of the variables or parameters which could be used to relate the viscosity of a gas-saturated oil to its dead oil viscosity. Preference was given to those variables which are easily and commonly measured in the field or in the laboratory. It was found that either the differential liquid formation volume factor or the solution GOR of the gas-saturated oil could be used as a correlating parameter. The solution GOR was se- lected for the correlation because of its simplicity and availability. In an attempt to refine the correlation by introducing a second parameter, the following additional variables were tested: differential liquid formation volume factor at the reservoir bubble point, the formation volume factor at the saturation pressure for the GOR of interest, reservoir temperature, viscosity of C+ fraction at 100°F and atmospheric pressure, weighted average gravity of gas in solution, oil gravity, reservoir bubble point pressure, saturation pressure at the selected GOR and reservoir temperature, and gas mol fraction. None of these improved the correlation to any significant extent. It was found that at any fixed solution GOR, the relation between the gas-saturated oil viscosities and the corresponding dead oil viscosities is a straight line on logarithmic coordinates, for the range of variables investigated. This straight-line relationship was used for the correlation. Viscosity data on a total of 457 crude oil samples were used. The data were obtained with rolling ball-type viscometers. The samples came from all of the important producing areas of the U. S., as well as from Canada and South America. Their geographical distribution is shown in Table 1. The ranges of properties represented by these samples are as follows: For each crude oil sample the viscosity of the liquid phase from each step of a differential liberation was plotted against its solution GOR on semi-logarithmic paper. A smooth curve was drawn through the points and values of viscosity in centipoises were read from

By R. M. Rose, C. S. Tedmon, J. Wulff

It is frequently of interest to study the influence of small quantities of interstitial impurities on the properties of various refractory metals and alloys.

Jan 1, 1964