Search Documents

By M. H. Forester, John D. Cooner

ALTHOUGH the unmined anthracite will last for approximately 150 years, most of the thicker and cleaner coal beds have been almost entirely first-mined and pretty well robbed, leaving much of the present and future production to come from thin and dirtier beds. Herewith is a section of one of the dirty beds being mined in the Wyoming region [ ] This section shows that 45.8 per cent of the bed is made up of impurities and that the 45 in. of coal in the bed is in five benches, the thickest of which is 19 in. In some localities of the anthracite region there are 14 beds of minable coal. Orderly and proper mining of the coal makes it necessary to rob or second-mine--almost all beds have already been first-mined-in sequence from the top downward. Therefore the robbing of the few remaining portions of the thicker and cleaner beds is in many instances being held up by the mining of the overlying thin and dirtier coal beds. Impurities Impurities consist of fire clay, slate, rock, and bone. The latter, which is black, contains 40 to 60 per cent carbon and often resembles good coal. In some beds there are also bands of "blue" coal, which, as the name implies,

Jan 1, 1950

By R. G. Jones, W. L. Kinney, R. E. Schilson, R. S. Wilson, G. A. Clark, H. Suralo

This paper describes the field opeturluns at the Fry in situ combustion project in Crawford County, 111. Field operations may be divided into three phases—-preliminary engineering studies of 1960 and 1961, ignition, and, finally, operation of the test. The Fry combustion project was a pilot test of cocur-rent in situ combustion on a 3.3-acre inverted five-spot. In the summer of 1960, air injection tests were conducted using old wells in the area and a new air injection well drilled especially for the test. In the summer of 1961, four new oil wells were drilled on a 3.3-acre pattern for the pilot test. All old wells in the near vicinity of the pilot test were abandoned to preclude any possibility of gas escaping to adjacent formations. A compressor plant was also installed at the test site in 1961. Air injection tests and other engineering studies were made. At the conclusion of these tests, ignition was accomplished with a 40 kw electrical igniter. Operation of the Fry combustion test was little different from the usual oilfield operation with the exception of the high rate of air injection. No difficulty was found with the openhole completion. There were no unusual corrosion or emulsion problems until bottom-hole temperatures exceeded 150F. Four cores were drilled into the burned-out portion of the reservoir with no mechanical difficulties. INTRODUCTION A cocurrent or conventional in situ combustion test was conducted on the Fry unit of the Marathon Oil Co., in Crawford County, Ill. Besides testing combustion in the Fry type of reservoir, the test was intended to evaluate various operating procedures. This paper presents a discussion of the Fry combustion test field operations. The geology of the reservoir and the test performance are discussed in other papers.'.' HISTORY OF THE FRY UNIT The Fry unit consists of 11 leases totaling 337 acres in an area in which oil was originally discovered in 1906. Production from this reservoir, as from all Robinson sand reservoirs in the area, was very high during the first few years. As the dissolved-gas energy was dissipated, early attempts to retard the decline consisted of vacuum, air, and gas repressuring, and recently, most of the area has been subjected to water flooding. Following early air repressuring, the Fry waterflood unit was formed and water flooding initiated in July, 1952. In the area in which the Fry combustion test was conducted, a peripheral water flood of a 160-acre area was developed as shown in Fig. 1. Between 1956 and 1960, it became apparent that the water flood was unsuccessfd. In looking for a suitable site for an in situ combustion test, the Marathon Oil Co. selected the Fry unit as possessing those features most desirable for such a research project. Field operations associated with the Fry combustion test began in the spring of 1960.

Jan 1, 1966

By T. L. McCall

The late Walter Herd1 in 1929 gave a full description of past and present conditions in No. 2 mine, Springhill, Nova Scotia, developed theories regarding the cause of these bumps and made certain suggestions regarding possible methods of future development. Recapitulating briefly from Mr. Herd's paper, the seam is bituminous coal, averages 9 ft. in thickness and has a well defined parting containing fusain about 14 in. from the roof. This roof coal is somewhat stronger than the rest of the seam and has a tendency to cling to the roof. The pitch of the seam where it is now being worked is about 20". The first manifestations of bumps began when the room and pillar workings had reached a depth of cover of 1900 ft. and under continuously increasing depth of cover these bumps increased to such an extent, both in number and severity, that in the year 1924 it became apparent that some change in the system of extraction was necessary. After closely studying all the factors involved and benefiting largely by valuable outside advice obtained by the Provincial Department of Mines of Nova Scotia,2 the system of working was changed from room and pillar to longwall retreating. Mr. Herd's paper described in detail three remarkable bumps in the year 1928 in April, July and October that affected the 5700-ft. and 5900-ft. East levels, the last bump being so severe both in intensity and in extent of damage done that this district was abandoned. The longwall workings to the west of the slope had been stopped in the year 1926 owing to an inbreak of water, coming from the flooded waste of No. 3 seam lying some 400 ft. vertically overhead. This inflow was not excessive, but a large quantity of water being impounded in the old workings it was considered advisable to take the prudent course and not incur the risk of possibly increasing the flow by further working. This district has remained idle ever since.

Jan 1, 1934

CHARGING of an open-hearth heat is begun as soon as possible after the previous heat has been tapped. Ordinarily, about 40 min is required to drain and dress the furnace hearth, make up the taphole, and perform routine repairs of the banks. Repairs to the upper back wall and to the front wall and jambs can ordinarily be done while the first scrap charge is being heated and are therefore allowed to wait in order to save furnace time. Any major repairs required on the hearth or other parts of the furnace necessitate longer delays because such repairs must be made while the furnace is empty. Although charging practice varies considerably in detail with the type and proportions of scrap and iron used, many factors are common to all varieties of charge. Such general considerations are dealt with first. CHARGING EQUIPMENT AND STOCK HANDLING The physical equipment available for loading and weighing the stock, transporting it to the furnace, and charging it, may have a major effect on charging practice. Limestone, scrap, and all other solid melting stock are charged mechanically by means of equipment illustrated in Fig 2-1. The charging of hot metal is shown in- the background of this figure. Mechanical equipment and plant layout for stock handling are described in Chapter 1. It is generally desirable to charge the scrap about as fast as the physical volume can be put into the furnace. Charging scrap that is too heavy or adding the charge too rapidly (less than 45 min) may be detrimental to melting rate because of excessive chilling of the entire furnace system and also because of poor conduction of heat to the lower layers in the furnace; but the more common problem is the reverse one of charging light scrap fast enough to maintain a normal heat time. A limiting factor may be the height to which the scrap may he piled in the fur-

Jan 1, 1964

By Ralph Arnold

WITHIN the past three weeks the price of crude oil in the Mid-Continent field has been cut 50 .per cent. Similar action has been taken, or probably, shortly will be taken, in most of the other fields of this country. This cut is very drastic. Is it justified? Some of the causes advanced for the cut are: that it is in line with the industrial downward readjustment now taking place throughout the country, and that there is an over-production of oil, which can best be slowed down by lowering the price of crude. In part, these two reasons are logically advanced, but such underlying causes as the great production- in Mexico have not been prominently brought forward nor the fact that it would be advantageous at this time to fill up the empty storage of many of the consuming companies at a low 'price. In order to properly comprehend the situation let us compare for a moment the production- of oil in the United' States and that in Mexico. Oil in the United States occurs in numerous often widely separated pools, varying in individual area, but each usually relatively extensive, compared to the area or gathering ground from which it is ultimately derived: It occurs in mod-erately porous reservoir rocks under such conditions of pressure, mobility and availability as to preclude its withdrawal except over a period of years-varying from 1 to at least 40 (average, say 15 years, depending on-the pool). One well will usually drain a limited area-2 to 10 acres-so that rate of withdrawal of oil under each owner's property is determined by the owner. - The important point to remember is that no matter how intensive the development, the oil reserves of -the United States cannot be materially exhausted' for at least 20 years, and the total available supply, not including shale oil, will probably require 50 to 75 years, or longer, for its withdrawal, the yearly rate of production decreasing slowly from this time on.

Jan 1, 1921

By N. S. Greensfelder

The firing of explosive charges by electricity dates back to 1745 when a Doctor Watson is said to have used an electric spark for igniting gunpowder. His method failed in practical application because, to ignite blasting powder, heat must be applied for a period longer than the duration of an electrostatic spark; Wheatstone found that this does not exceed 1/24000 sec. The usual result, therefore, of an electrical discharge in gunpowder is to scatter the grains, without igniting them. Benjamin Franklin partly overcame this difficulty by confining the powder and crushing grains that lay in the line of discharge. In 1822, after the primary cell had been discovered by Volta, Robert Hare, professor of chemistry at the University of Philadelphia, noticed the heating of a short piece of wire placed in the circuit of a voltaic battery. Later work by Oersted, Faraday, Wheatstone, and Henley resulted in the developmcnt of the magneto blasting machines. Fulminates of gold and silver are thought to have been discovcrcd by Cornelius Drebbel, about 1600. Pepys, in his diary for November 11, 1663, recounts a conversation with Doctor Allen, who told him about aurium fulminans "of which a grain ... put in a silver spoon and fired, will give a blow like a musquett and strike a hole through the silvel spoon downward, without the least force upward.'ll This fallacious belief that explosives act downwards only is still held by many who should know better. Fulminate of mercury was discovered by Howard in 1799. J. Shaw of Philadelphia is said to have invented a fulminate-of-mercury cap in 1814; his idea was later adopted by gunmakers in England and France. The principal advantages of mercury fulminate for use in detonators are the simplicity of exploding it and the great shock developed by its explosion.

Jan 1, 1923

By Edward Wichers

THE purpose of this paper is to set forth the matters of principal interest in connection with work done in the past few years on the purification of the metals of the platinum group, including the study and modification of methods already in the literature and the development of new procedures. For the most part, the results will be given in summary form, reserving the publication of detailed data and directions for a forthcoming paper to be issued by the Bureau of Standards. In recent years increasing interest has been shown in the preparation of the pure platinum metals, both by those concerned with the manufacture of the metals and their alloys for scientific and industrial purposes and those who are engaged in the study of the chemical or physical properties of the elements. The purification of the metals usually has been regarded as a matter so involved and difficult as to require the attention of specialists. It is hoped that this paper will show that any of the metals can be prepared in any desired degree of purity by relatively simple straightforward chemical methods. For the most part, it is thought that the methods given are suitable for small-scale refineries as well as for the laboratory; also, that they will bring the time required for the purification of any of the metals within reasonable limits. The new procedure suggested for purifying platinum should prove to be much shorter than any methods described in the literature.

Jan 1, 1928

By N. S. Greensfelder

The firing of explosive charges by electricity dates back to 1745 when a Doctor Watson is said to have used an electric spark for igniting gunpowder. His method failed in practical application because, to ignite blasting powder, heat must be applied for a period longer than the duration of an electrostatic spark; Wheatstone found that this does not exceed 1/24000 sec. The usual result, therefore, of an electrical discharge in gunpowder is to scatter the grains, without igniting them. Benjamin Franklin partly overcame this difficulty by confining the powder and crushing grains that lay in the line of discharge. In 1822, after the primary cell had been discovered by Volta, Robert Hare, professor of chemistry at the University of Philadelphia, noticed the heating of a short piece of wire placed in the circuit of a voltaic battery. Later work by Oersted, Faraday, Wheatstone, and Henley resulted in the developmcnt of the magneto blasting machines. Fulminates of gold and silver are thought to have been discovcrcd by Cornelius Drebbel, about 1600. Pepys, in his diary for November 11, 1663, recounts a conversation with Doctor Allen, who told him about aurium fulminans "of which a grain ... put in a silver spoon and fired, will give a blow like a musquett and strike a hole through the silvel spoon downward, without the least force upward.'ll This fallacious belief that explosives act downwards only is still held by many who should know better. Fulminate of mercury was discovered by Howard in 1799. J. Shaw of Philadelphia is said to have invented a fulminate-of-mercury cap in 1814; his idea was later adopted by gunmakers in England and France. The principal advantages of mercury fulminate for use in detonators are the simplicity of exploding it and the great shock developed by its explosion.

Jan 1, 1923

By Robert L. Greyer, John I. Myung

The Birdwell 3-D Velocity Log displays photographically the amplitude of elastic waves as a function of time and of the depth of the logging tool in a borehole. The elastic waves are generated by a magneto-strictive source transducer and detected by a receiving transducer, which is at a fixed distance from the source. The output of the receiver, which is proportional to the amplitude of the received elastic waves, modulates the light that exposes the film record. The duration of the receiving time can be selected to record the entire wavetrain of late events or to record only early events at a finer time scale. When a full complement of elastic waves (i.e., the refracted compressional wave, composite shear wave, direct fluid wave, and boundary wave) is recorded, their velocities and the density of the borehole fluid provide the information necessary to compute the elastic moduli and density of the rock surrounding the bore-hole. The differences between the values of the moduli determined from measurements of 3-D Velocity Logs and by other better known techniques are small, well within the limits of experimental error, when the velocity log is interpreted by an experienced seismic analyst. INTRODUCTION Quantitative descriptions of the mechanical properties of the rock environment have long been basic requirements of planning, design, and quality control of engineering projects. Because of this need, many techniques for determining the elastic moduli from static and

Jan 1, 1971

By George Frederick Kunz

The manifold inconveniences resulting from the absence of a uniform standard of mass for determining the weight of precious stones have long been obvious. This lack has been keenly felt in commercial transactions, and those who have devoted time and research to the study of historic diamonds and precious stones have had frequent occasion to deplore the absence of such a standard in the past. In a paper read in Chicago in 1893, before the International Congress of Weights and Measures, held in connection with the World's Columbian Exposition, the writer suggested dividing the carat into 100 parts, and constituting a standard international carat of 200 mg.; that is, 5 diamond carats or 20 pearl grains to a French gram, making 5,000 carats or 20,000 pearl grains to a ki1ogram. He also called attention to the fact that while this would depreciate the present diamoiid carat or pearl grain only about 2.5 per cent., it would abolish the troublesome discrepancies between the various carat-weights now in use, and could be easily explained and understood everywhere.' The subject of the various diamond carats, their incongruity, and the resulting confusion as to the correct weights of historic gems when definite records of them are searched for, has been fully treated by me in an extensive study of this subject in The Book of the Pearl2 To the earnest and unremitting efforts of C. E. Guillaume, Director of the Bureau Internationale des Poids et Mesures at Sévres, is largely due the eventual success of this eminently desirable reform, which he has constantly urged both by articles on the subject and by addresses delivered in Paris before the International Committee for Weights and Measures.3 The general adoption of a uniform standard for dealings in pre-

Jan 1, 1914

By Thomas Egleston

The copper-bearing rocks of Lake Superior are composed of a series of metamorphic rocks, comprised under the names of amygdaloid and conglomerate, in which the copper and silver found with them are pseudomorphs. These rocks, generally, have Well-defined walls which cause them to separate easily. Generally, the country rock is sterile, but it occasionally rises into the copper-bearing rock, and then carries copper. Usually, the amygdaloids carry copper, and the greenstones or melaphyres which encase them do not. There is a very generally received opinion that the copper in these beds occurs in shoots. This does not appear to be proved, though the opinion seems to have some foundation from the experience of the Calumet & Heela Mine, where a body of poor rock has been left, which, on the mine map, shows a general direction. The theory may be true of that individual mine, but too little work has been done in the other mines to draw any decided conclusion. The copper is very unequally disseminated in the rock, if any given piece be taken as an example, but, if the whole copper-bearing series be considered, its distribution is uniform. It may prove that there are certain directions in which the copper has been deposited more abundantly than in others, and these may be found to correspond with certain geological causes, but up to the present time the knowledge gained is not sufficient to warrant any general conclusion. These rocks are supplemented by a series of true fissure veins, of which there are several systems, making the amount of native copper very large. Unfortunately, except in the fissure veins, known as " mass-mines," the copper is so scattered through the rock, and is in such a fine state of division, that, although it is not always difficult to mine, it is always difficult to dress it sufficiently to make it pay. The metal is so unifornily distributed throngh these copper-bearing rocks that detached pieces, called " float," are found in digging on almost any land in the country. These pieces vary from very small fragments, weighing not more than a few ounces, up to many pounds. In one instance, in making an excavation for a cellar of a

Jan 1, 1879

By Arthur Fleischer

THE Kalunite process? for the production of metal-grade alumina from alumina-containing ores is applicable, considered from a general point of view, to any aluminous raw material that can be converted to potassium alum or equivalent normal alum. This result of modern technology has been the subject of a continuous study and development since 1929, on a laboratory and test-plant scale, with initial emphasis on the utilization of alunite as the raw material. The research and developmental program was carried out by the Kalunite Company and its successor, Kalunite, Inc., an affiliate of the Olin Corporation of East Alton, Illinois. The process is now approaching the time for a major test in its history with the completion of construction of a plant having a capacity of zoo tons of alumina per day in Salt Lake City for the conversion of Marysvale, Utah, alunite ores to alumina and potassium sulphate. The Salt Lake Alumina Plant is a Defense Plant Corporation project. PRODUCTION OF ALUMINUM The known existence of alunite deposits, especially in the Marysvale district, furnished the motive for the original inquiry into the utilization of this raw material for aluminum production. The deposits in this region were actively explored during World War I and utilized for the production of potassium sulphate, an essential fertilizer, of which a shortage of monumental proportions then existed. Up to the twentieth century for alunite is a mineral with an ancient history-it was used in Europe and in China as a source of potassium alum. It never had been used successfully in. this country as a source of oxide for reduction to metal. Although the known reserves of this ore, which undoubtedly will be greatly expanded with a commercial outlet for this ore, are recognized to be sufficient for only a part of the present-day needs of aluminum, it has a definite place in the aluminum industry. Academically it points the way for future raw materials. The aluminum industry has undergone a remarkable growth in the past few years as a result of defense and war requirements. Its expansion in many ways has been beyond belief and prediction, both in volume and location. This wartime status of the industry has accelerated the consumption of bauxite to such an extent, that a re-evaluation of the raw material reserves for the future peacetime industry and for eventual wartime reserves is seemingly of concern. The generally accepted picture of bauxite ore reserves in the United States, especially in raw material suitable for treatment by the Bayer process, focuses attention on other possible sources of raw material of metal-grade oxide. The perspective for the development of a suitable process may have changed in the interim

Jan 1, 1944

By Roswell H. Johnson

What becomes of the water which must have filled the oil and gas sands at the time of deposition, has long puzzled students of oil and gas and has found expression in Munn's well-known article on the hydraulic theory. Both Munn and Clapp have pointed out that in the Appalachian field the deeper sands carry increasingly less proportionate amounts of water. It seems to me probable that the principal source of oil and gas has been in the shales in proximity to the sands which now contain these products. The sand spits which mark off the lagoons from the sea comply particularly with the requirements of a limited sand imbedded in shales rich in organic matter. Cunningham Craig has objected to this view that the rich organic muds of lagoons are found only at the surface. That such muds do extend to considerable depth 1 am assured by Prof. Douglas W. Johnson, who has made an extensive study of the Atlantic Coast marshes. As any particular sand body becomes weighted by a heavier and heavier overburden, the result of increasing deposition, a part of the very large percentage of water in the uncompacted sand and mud is forced out. The water percentage of freshly settled mud is vastly higher than that of the resultant shales, or even of a very porous sand. If beds of less compressible material meet or underlie the shales in question, there will frequently be a lateral motion along such beds to some point where the upward movement will be resumed. We find in our laboratory work here that oil, gas, and water have extremely slight capacity for gravitational sorting while in a state of rest, but when moving the gravitational sorting is readily accomplished. As the oil, gas, and water pass a body of larger pores, the gas, owing to its lack of capillary attraction, is retained in the large pores. This has been predicted by Washburne, Blatehley and others on the ground that the water has a higher capillarity and grips the finer pores in such a way that there will be a greater proportion of oil and gas in the large

Jan 1, 1915

By James G. Crawford

Correlation Of water with its reservoir zone or formation has been one of the applications of oil-field water analysis of greatest direct value to the petroleum engineer. The water in each producing zone tends to have diagnostic characteristics by which it can be distinguished from every other water above or below that zone in that immediate vicinity. Representative analyses of oil-field waters from producing oil and gas fields in the Rocky Mountain region are included, and the diagnostic characteristics are discussed briefly. It is concluded that the generally dilute nature of Rocky Mountain oilfield waters is a result of dilution by meteoric waters, and that there is no relationship between presence or absence of commercial oil and the character of water in a structure. Introduction The study of waters associated With oil and gas began more than 50 years ago and has been well recognized by operators, engineers, and geologists for about 30 years. It appears unnecessary at this time to recite the history of oil-field water analysis; suffice to say that it has proved its worth many times to the production engineer suddenly confronted with water problems in producing oil and gas wells. Chemists and geologists have studied the possible origin of these waters and as Yet the subject is unsolved in many important phases. There are both local and regional problems connected with the explanation of concentrations and character- istics peculiar to each field, each subsurface zone and each province. Criteria useful in postulating the Occurrence of oil Or gas in One province completely fail when applied to another, and data carefully prepared and analyzed from one field may be actually misleading when applied to another. Correlation of water with its reservoir zone or formation has been one of the applications of oil-field water analysis of greatest direct value to the engineer. The concentrations and characteristics of the waters are essential to the engineers and geologists making interpretations of electric logs in this region. The behavior of water under conditions of reservoir temperature and pressure is dependent to a great degree upon its concentration and characteristics, and thus important to the reservoir engineer. With the advent of secondary recovery methods in the Rocky Mountain region the characteristics and treatment of water will become increasingly important. Premises upon which Correlation Is Based A brief review of the geochemical history of oil-field waters will suffice to present the premises upon which correlations of the waters are based. Sedimentary rocks which are now stratified were first sediments in seas, lakes and streams. These sediments were filled interstitially with connate water. With burial the sediments were compressed arid consolidated, integrated and indurated into bed rock and much of the connate water was dispelled. Following the formation of bed rock the strata were sub-

Jan 1, 1949

IN A broad sense, the subject of slag control includes not only the adjustment of the composition of the slag but also of its relative weight in terms of percentage of the metal-bath weight. The slag is made up essentially of (1) oxides formed by oxidation of silicon, manganese, phosphorus, and iron in the charge, (2) SiO2, MnO, and other oxides charged as such, and (3) lime charged or fed to the heat to neutralize the “acidic”: oxides present (Si02 and P2O5). Obviously, if practically perfect control were possible over the composition of the charge as well as over the oxidation process during the melting period, both slag weight and composition would be very nearly predetermined, and the control problem would be solved. Unfortunately, we have only a somewhat. imperfect control over these factors, so that beginning at about the lime-boil period in the heat, and later in the early refining period, it becomes necessary for the first helper, as the heat progresses, to make quick estimates of the composition and physical state of development of the slag (as well as of the amounts of phosphorus, sulphur, and carbon in the metal) from which he can judge how much extra lime, roll scale, fluorspar, and other additions will be needed not only to give the desired final slag composition, but also to hasten the complete fusion or shaping to a desired viscosity in the liquid state. The discussion in this chapter is limited essentially to those more or less practical rapid methods of slag estimation that have been used, or at least tried, for these purposes under actual open-hearth shop conditions. Another aspect of importance here is the extent to which the freedom of choice to the operator is limited by available charge materials, product specifications, and the oxidation and other chemical- reaction effects which inevitably occur under the conditions of this furnace process. For a better understanding of these control limitations and of the chemical and physical background of the subject, the reader is urged to read at least part of the discussion in Chapters XVII and XIX. Charge materials are discussed in Chapter IV, and many of the details of charging, melting, and refining practice closely related to slag control are given in Chapters VI and VII.

Jan 1, 1944

By W. A. Anderson

Recrystallization of cold-worked metals has long been known to proceed by a process of nucleation and growth.' When a cold-worked metal is heated to a temperature at which recrystallization will ensue, nuclei of new grains, essentially strain-free, appear and grow. As the process proceeds, nuclei continue to appear and to grow, until the cold-worked matrix has been entirely consumed and recrystallization has been completed (Fig. I). Conducted isothermally, a measurement of the fraction of the matrix recrystallized plotted against time, yields an isothermal recrystallization curve, showing the time course of the recrystallization process (Fig. 2).2 Evidently, then, the rate of recrystallization is determined by the rate at which nuclei form and the rate at which they grow. The rate of nucleation N is the number of nuclei that form in unit time in unit volume of the unrecrystallized matrix, and the rate of growth G is the increase in radius of the recrystallized grain per unit time. In recent years attempts have been made to determine N and G as these vary with the well-recognized variables affecting recrystallization: time, temperature, degree of deformation, etc.1 Such studies yield information that is more fundamental than that conveyed by the conventional recrystallization diagram,' since the rate of recrvstallization is thus analyzed into its two component rates3 Methods are now available by which N and G can be measured, and analytical expressions have been developed for the interrelationships among N, G, the isothermal recrystallization curve, and the final grain size, which greatly facilitate analysis.2-4 The application of these methods has been demonstrated recently for the recrystallization of silicon ferrite.2 Data on N and G in dependence upon the recognized recrystallization variables are, however, very fragmentary;" values of N and G have been determined for some metals, but the effect of temperature, which would yield the fundamentally important activation energies, has been too little studied. Thus far there has been no detailed study of the recrystallization of any one metal in terms of X and G ovcr appreciable ranges of the variables time, temperature, degree of deformation, and original grain size. It is the purpose of the present paper to provide such a study, employing aluminum.

Jan 1, 1945

By Zay Jeffries

It has been known for centuries that iron and steel could be hardened by cold hammering and that the metal could be restored to the normal condition by heating to a red heat arid cooling, either rapidly or slowly with nearly pure iron, but slowly with steels containing considerable carbon. The art of tempering steels is also very old. When a medium- or high-carbon steel is quenched from a cherry-red heat, the hardness is increased; this hardness can be reduced by heating to various temperatures below the lower thermal critical point,, which is near 700" C. The present paper will not consider these old and well known changes in iron and steel below the thermal critical range but will confine itself to the more unusual changes, some of which have been studied recently. Stromeyer,1 for example, In 1886, reports that both working steel and heat treatment of steel in the blue-heat range arc highly injurious. Recently, however, some metallurgists believe that the straiglltening of warped steel forgings at a blue heat produces a beneficial effect on the metal2 The Engineering Division of the National Research Council has constituted a committee on Physical Changes in Iron and Steel below the Thermal Critical Range, which has the following personnel: K. R. -Abbott, H. C. Boynton, William Campbell, J. V. Emmons, F. B. Foley, H. J. French, H. M. Howe, Zay Jeffries (chairman), F. C. Langenberg, J. A. Mathews, P. D. Merica, A. H. Miller, J. H. Nelson, G. A. Reinhardt, W. E. Ruder, H. F. Wood. This committee is studying several aspects of the physical changes in iron and steel. The results, reported in the literature and obtained by recent experimentation, will be given; this will be followed by a general theoretical discussion of the more important

Jan 1, 1922

By Robert Glass Cleland

THE CONNECTING link between Phelps Dodge and the copper mines at Bisbee and Morenci was a Canadian-born mining engineer and metallurgist named James Douglas. Judged by almost any standard, Douglas was an extraordinary man. Like John Muir of the California red- woods, he had in his blood "the heather and bog juices of Scotland," and the rugged virtues of a singularly great race. His father, for whom he was named, was a graduate of Edinburgh University, a member of the Royal College of Surgeons in London, and a man of rash and adventurous spirit. Extremely catholic in his intellectual interests and attainments, he was unusually skilled in his profession, certain-sometimes to the point of disastrous stubbornness--of his own judgments and decisions, careless of life or fortune where duty or moral issues were involved, and always deeply moved by the sufferings and misfortunes of his fellow men. The career of the senior Douglas included a curious medley of novel and adventurous experiences-prolonged hunger and cold while acting as surgeon on a Greenland

Jan 1, 1952

By E. N. Doyle

Since the mid-1930's a number of plants, using the principles of heavy media separation, have been installed throughout the world. In cases involving lead, zinc or lead-zinc ores the reasons for the choice of this type of beneficiation process have fallen into four major categories: A) The economic recovery of additional distinctly separate products, such as dolomite limestone at the Mascot Plant (1) of the American Zinc Co., and the ferrosilicon produced by St. Joseph Lead Company. (2) B) The elimination of a large portion of run-of-the-mine ore prior to grinding and flotation, to allow increased throughput with low capital cost. Examples of this approach are the Levante and Ponente plants of the Montevecchio Company in Italy (3) and the frequent choice of the Sink-Float process by the Penarroya Company of Paris. C) The processing of a sedimentary deposit, in which the valuable mineral is contained in the matrix separating the boulders, as was the case at the St. Joseph Lead Company plant at Haydon Creek (4) and also at Bunker Hill Mining and Smelting, Kellogg, Idaho. D) The simplification of Around support programs in mines by allowing greater freedom of action in the extractive pattern. An example of this choice is Cominco’s Sullivan plant which came into being as part of an extensive proposal to update the mining, crushing, transportation, grinding and beneficiation processes. (5)

Jan 1, 1970

By Zay Jeffries

It has been known for centuries that iron and steel could be hardened by cold hammering and that the metal could be restored to the normal condition by heating to a red heat arid cooling, either rapidly or slowly with nearly pure iron, but slowly with steels containing considerable carbon. The art of tempering steels is also very old. When a medium- or high-carbon steel is quenched from a cherry-red heat, the hardness is increased; this hardness can be reduced by heating to various temperatures below the lower thermal critical point,, which is near 700" C. The present paper will not consider these old and well known changes in iron and steel below the thermal critical range but will confine itself to the more unusual changes, some of which have been studied recently. Stromeyer,1 for example, In 1886, reports that both working steel and heat treatment of steel in the blue-heat range arc highly injurious. Recently, however, some metallurgists believe that the straiglltening of warped steel forgings at a blue heat produces a beneficial effect on the metal2 The Engineering Division of the National Research Council has constituted a committee on Physical Changes in Iron and Steel below the Thermal Critical Range, which has the following personnel: K. R. -Abbott, H. C. Boynton, William Campbell, J. V. Emmons, F. B. Foley, H. J. French, H. M. Howe, Zay Jeffries (chairman), F. C. Langenberg, J. A. Mathews, P. D. Merica, A. H. Miller, J. H. Nelson, G. A. Reinhardt, W. E. Ruder, H. F. Wood. This committee is studying several aspects of the physical changes in iron and steel. The results, reported in the literature and obtained by recent experimentation, will be given; this will be followed by a general theoretical discussion of the more important

Jan 1, 1922