Search Documents

By Y. C. Liu, G. A. Alers

The effect of rolling reduction on the textures of Cu-A1 alloys has been investigated both by pole figure and by modulus methods. In alloys which exhibit complete copper or brass types of rolling texture, the rolling reduction has little effect on the texture except to increase the degree of preferred orientation. In alloys which exhibit a transition texture, however, increased rolling reduction increases the amount of brass-type texture at the expense of the copper-type texture. The present experimental results show that there is no one-to-one correspondence between the SFE and the rolling texture of fcc metals. Additional data taken from the literature for fcc metals also support this conclusion. On the other hand, the present and previous experimental results are shown to be in good agreement with the suggestion that the texture transition occurs at a critical value for the separation distance between two partial dislocations—a consequence of the "dislocation interaction" hypothesis for texture. formation. This critical separation occurs when the parameter .r/ub is 3.75 x 10'3. From this, a value for the SFE of 39 ergs per sq cm may be deduced for a Cu-2.85 at. pct A1 alloy. ThE correlation between the rolling texture of fcc metals and the stacking fault energy, SFE, was one of the first attempts to relate atomistic properties with the type of rolling texture.' This correlation gives a qualitative explanation for the experimental observation that the addition of alloying elements, which generally lower the SFE, changes the copper-type texture to a brass-type texture. The simplicity of this correlation had led to its general acceptance and even its quantitative use.' However, it is only a correlation and is largely based on descriptive features of pole figures, and on the poorly known SFE values in dilute alloys. Quantitative verification of this phenomenologi-cal correlation is, in fact, completely lacking. One purpose of the present study is to test this correlation. Another atomistic description for the formation of rolling texture is the "dislocation interaction" hypothesis of texture formation.3 In this hypothesis, the factor controlling the type of rolling texture depends on whether or not the separation distance between two partial dislocations exceeds a critical value. Materials having a separation of less than the critical value are supposed to exhibit a copper-type texture while those with a separation above the critical value are supposed to have a brass-type texture. At the critical value, it is expected that the material should show equal amounts of copper- arid brass-type orientations in their textures, i.e., a 50 pct transition texture. The SFE appears in this hypothesis as only one of several factors which determine the separation distance between partial dislocations. It is possible to test the validity of these two concepts by studying the rolling texture as a function of rolling reduction. Since the SFE per se is an intrinsic property of the metal, it should not, by definition, be influenced by local irregularities, such as variable stress conditions. Thus, no change in texture-type is expected to occur with changes in rolling reduction. On the other hand, according to the "dislocation interaction" hypothesis, any factor that effectively influences the separation distance of partial dislocations would be expected to change the rolling texture. Since the separation distance between partial dislocations is known to depend upon local stresses,4-6 it is anticipated that there would be an effect of the degree of reduction on the texture-type. Also, since applied stresses are more likely to increase, rather than to decrease, the separation between partials,4'5 the overall effect would be to increase the amount of material in the brass-type orientations as rolling reduction is increased. Furthermore, this reduction dependence would be most prominent in alloys exhibiting the transition texture since the distance between partials in those alloys is thought to be close to the critical value. Experimental data in the literature is insufficient to distinguish between these two alternatives. Haessner studied the effect of rolling reduction on textures in a series of Ni-Co alloys by means of the X-ray intensity-ratio technique,' and found that while one texture parameter indicated no reduction dependence the other indicated a slight dependence of the rolling texture on reduction in the range of 96 to 99 pct. As has been noticed previously, the intensity-ratio technique is a convenient but controversial method7 because there is no a priori reason to suggest which intensity-ratio would describe the texture most meaningfully. A more quantitative method of describing textures is found in terms of the orientation dependence of Young's modulus. Here, the type of modulus aniso-tropy associated with the copper-type texture is sufficiently different from that observed for the brass-type texture to allow the two types to be easily distinguishable and a quantitative measure of the amount of each can be deduced from the numerical results. This ability to provide quantitative data is particularly valuable when the two textures occur simultaneously in one alloy as is the case for the transition textures. In this paper the modulus method, supplemented by pole figure data, is used to look for an effect of roll: ing reduction the texture. Also by combining the texture measurements with recent determinations of the SFE in Cu-A1 alloys'0'" it should be possible to test for a relationship between the SFE and textures.

Jan 1, 1970

By G. A. Chadwick, D. Jaffrey

The morpho1ogies and orientation relationships of the phases in the Sn-Zn and A1-A13Ni eutectic systems were examined by electron microscopy and X-ray diffraction techniques. In each alloy the "transition" from the lamellar to the fibrous morphology was found to be one of scale, not of type. The minor phase in both systems exhibited certain well developed facets which were not affected by changes in the ingot solidification rate. The crystallographic relationships displayed by the pairs of phases in both systems were also insensitive to the growth rate. In the Sn-Zn alloy, the unique relationship of: growth direction - II [1201 Sn - II [01101 Zn and ribbon interface plane 11 (101) Sn 11 (7012) Zn was determined. The Al-Al3Ni alloy phases did not possess any particular orientation relationship, though the Al3Ni phase invariably grew in the [010] direction and exhibited the same set of facet planes. These results are discussed in relation to current eutectic growth theories and explanations of the "lamellar to fibrous transition". THE lamellar to fibrous transition that occurs in many eutectic alloys has been the subject of considerable speculation and experimental study. In some alloys it can be induced solely by an increase in the solidification rate,'-3 whereas in others the transition supposedly occurs only if the lamellae are forced to grow out of the overall ingot growth direction.4-6 he cause of this latter type of transition has been attributed to deviations of the lamellae from their low energy habit planes;4'5'7 fibers are produced because the sustaining force for lamellar growth (a low energy boundary) is destroyed. Implicit in these explanations is the assumption that fibers are circular in cross-section and completely lacking in low energy inter-phase interfaces. The "natural" growth rate dependent transition has been studied less thoroughly although Tiller8 has attempted a theoretical explanation of it. Tiller's arguments are not completely satisfactory9 but his suggestion that the relative undercoolings of the solid/liquid interface for lamellar and fibrous morphologies are growth rate dependent cannot be totally discounted; it is possible, for instance, that the relative interfacial undercoolings could alter and produce the observed morphology change if the orientation relationships between the phases and the associated interphase bound- ary energies were sensitive to growth rate. Salkind et al." have reported finding a change in the orientation relationships in the A1-A13Ni system accompanying the lamellar to fibrous transition, but contradictory evidence has also been reported for this3'" and another system,12 so the position remains unclear. In an attempt to clarify matters a study was made of the "lamellar to fibrous" transition in the Sn-Zn and A1-A13Ni eutectic systems; the morphologies of these two selected systems are quite similar when viewed by optical microscopy. In the present research the morphologies and morphology changes were investigated by electron microscopy. The orientation relationships existing between the eutectic phases were also determined for both morphologies in both eutectic systems. EXPERIMENTAL PROCEDURE The materials and method of alloy preparation and ingot solidification for the Sn-Zn system have been reported previously.2 In this investigation nine horizontally grown ingots of the highest purity (99.9997 pct) were used. The temperature gradient in the melt was not intentionally varied and was approximately 10°C per cm. Seven growth rates between 1.3 cm per hr and 20 cm per hr were imposed. The A1-A13Ni alloys were prepared from "Spec. Pure" nickel and 99.995 pct aluminum by melting the components in an open alumina crucible and casting the melt into the cold graphite mold. Six ingots of the Al-Al3Ni alloy were unidirectionally solidified at growth rates from 1 cm per hr to 12 cm per hr under high purity argon. A typical ingot was 20 cm long, 1 cm wide, and 0.75 cm to 1.5 cm thick. Samples taken from the bars at positions 12 cm from the nucleation end were examined by conventional orthogonal-section metallo-graphic techniques. When required, samples were mounted for X-ray diffraction analysis using the Laue back-reflection technique with a finely focussed X-ray source. The surfaces of the A1-A13Ni specimens were prepared by mechanically polishing them down to the 1 µ diamond pad stage followed by an electropolish in 80/20 methanol/perchloric acid solution at 0°C and 20 to 30 v. The Sn-Zn specimens were repeatedly polished on an alumina pad and etched in hot dilute (2 pct) nitric acid until the diffraction spots were found to be sharp. Thin films of the alloys were prepared for observation in an electron microscope by spark machining thin discs (0.03 to 0.04 in. thick) from longitudinal and lateral sections of the bars and elec-trolytically thinning them via a jet polishing technique. For the A1-A13Ni eutectic alloy, an 80/20 mixture of ethanol/perchloric acid at 40 v and 20°C was found to be satisfactory. A solution of 70/20/10 methanol/perchloric acid/butylcellosolve at 25 v and 20°C was used on the Sn-Zn alloy. For the former alloy the jet nozzles (cathodes) and the disc clamps were of aluminum;

Jan 1, 1970

By J. Leja, J. H. Schulman

FROTH flotation is usually effected by the addition of a collector agent and a frothing agent to an aqueous suspension of suitably comminuted mineral ores. The action of collectors is to adsorb onto the surfaces of minerals to be separated, sensitizing them to bubble adherence. The action of frothers has, in the past, been accepted as that of froth formation only, brought about by a lowering of the air/water interfacial tension. Substances capable of producing froth are classed1a,b according to their relative capacities for production of froth-volume and froth stability in the simple frother-water system. The purpose of this paper is to show that the surface active agents acting as frothers become effective only when there is a suitable degree of molecular interaction taking place between collector molecules and frother molecules at the air/water and solid/ water interfaces. Further, the discussion will demonstrate that the actual mechanism of adherence of an air bubble to a suitably collector-coated particle is due to the molecular interaction collector-frother. This leads to the formation of a continuous interfacial film of associated molecules, anchored to the mineral by polar groups of the collector, and enveloping the whole bubble. The tenacity of adhesion mineral-to-bubble results from the strength and the visco-elasticity of this mixed film. Some 20 years ago Christman2 postulated mutual dependence of collector and frother in effecting flotation. This view was, however, strongly opposed by Wark,3 who pointed out that an addition of frother had no effect on the value of contact angle once this was established in the solution of collector. More recent work by Taggart and Hassialis' indicated that the presence of frother, namely, cresol, leads to the immediate establishment of a contact angle on sphalerite, partially coated with xanthate, whereas an air bubble fails to make contact in potassium ethyl xanthate solution alone, even after 60 min induction time. Wrobel5 raws attention to the selectivity of frothers in flotation. Many instances of antagonistic effects of certain mixtures of frothers (or collectors and frothers) on flotation froth have been known to flotation operators and have been reported in literature. Taggart6 and Cooke7 give several examples of incompatibility of certain ratios of frothers and collectors, e.g., oleate and long-chain sulphates, pine oil and soaps. Monolayer Penetration. Properties of insoluble films produced by molecules of surface active agents orientated at the air/liquid interface are conveniently studied by the Langmuir trough technique, described fully by Adam.' Using the trough technique Schulman and Hughes" and Schulman et al.10a. b, c, d,e established the existence of molecular interactions occur- ring between certain types of surface active agents. Their experiments revealed the phenomenon of penetration of an insoluble monolayer (e.g., a film of a long-chain alcohol) by a soluble agent (e.g., sodium alkyl sulphate) injected into the substrate (water or salt solution). The degree of molecular interaction taking place on penetration is determined by changes in the surface pressure of the resulting film, changes of its surface potential and its mechanical properties (viscosity and rigidity). When the interaction takes place between both polar groups and both hydrophobic groups of the two participating amphipathic molecules a molecular complex is formed. Complexes formed on penetration of the monolayer at interfaces are not necessarily true chemical compounds: they are labile in solution, the activity and reactivity of individual components are greatly different from those of the molecularly associated complex, and on crystallization they usually separate out into components. However, when formed in the orientated state at interfaces they are found to be very stable, although some mixed films spread as monolayers of stoichiometric complexes can show further penetration by subsequent additions of the soluble component injected into the substrate.'" The degree of association between two or more types of surface active agents is very sensitive even to small changes in electric (dipole) moment of the polar groups of the amphipathic molecules as influenced by magnitude and position of neighboring ions or dipoles, their size, concentration, and stereochemistry. In addition, the molecular association is greatly influenced by concentration and type of inorganic salts in the substrate, by its pH, and by temperature. The nonpolar groups of interacting molecules greatly affect the stability of molecular complexes. Progressive shortening of the aliphatic chain of one of the reacting molecules weakens (at an increasing rate) its tendency to form stable complexes. Similarly, introduction of a double bond of cis-form into one of the reacting chains, which changes the straight hydrocarbon chain into a kinked one, or introduction of a branched chain, reduces the stability of the associated complex. Monolayer Adsorption. Using the trough technique and injecting metal ions into the substrate (water or salt solution) underlying insoluble films of fatty acids, alkyl amines, and sulphates, Wolsten-holme and Schulman11a,b,e. ' and Thomas and Schulman" have established conditions, namely, pH, concentration. and steric factors, under which molecular interactions take place between the polar groups of the surface active agents and the metal ions. These interactions are marked by great changes in the solubility and mechanical properties of the monolayer of the agent; no surface pressure increases are observed as in monolayer penetration experiments. The results of these adsorption studies, correlated with flotation experiments, indicated that in the case of fatty acids and alkyl sulphates their adsorption onto minerals of base-metals takes place by a similar

Jan 1, 1955

By R. Bainbridge

THE Consolidated Mining and Smelting CO. of Canada Ltd. has operated a lead smelter at Trail, B. C., for many years. In order to take advantage of metallurgical advances, as well as to improve materials handling methods, this company, commonly known as "Cominco," commenced planning a program of smelter revision and modernization some years ago. The first stage of this program involved the design and construction of a new blast furnace gas cleaning system. The selection of equipment, the design of facilities, and preliminary operating details of this system will be dealt with in this paper. The essential problem was to clean and collect 100 tons of dust daily from 153,000 cfm* (12,225 lb per min) of lead blast furnace gas which varied in temperature from 350º to 1100°F. Because it was desired to collect the dust dry, either a Cottrell or a baghouse cleaning plant was to be selected. Comin-co's many years of experience with both systems provided a background for choosing the most satisfactory installation. All information pertinent to the two methods of dust recovery was carefully investigated, and it was decided to replace the existing equipment with a baghouse. Very briefly, the reasons for this decision were as follows: 1—A baghouse installation would be practical because the SO2 content of the gas was low and corrosion would not be a problem if the baghouse operating temperatures were held sufficiently above the dew point. 2—Variations in the physical characteristics of fume and dust, which are inherent in this blast furnace operation, should not substantially affect the operating efficiency of a baghouse. 3—For the same capital cost, metal losses (stack and water losses) would be appreciably less in a baghouse. 4—A baghouse would be easier to operate, and would not require the use of highly skilled labor. 5—Operating and maintenance costs of a bag-house would be lower. 6—The only available space for reconstruction was relatively small, and not suited to a Cottrell installation. Once the baghouse system was decided upon, detailed design of the installation was begun. Baghouse Design Gas Cooling: Before the required capacity of the baghouse could be determined, the method of cooling the gas to the temperature necessary for bag-house operation had to be chosen. The problem confronting the design engineers was how best to cool 153,000 cfm of gas from a temperature ranging from 350°F to brief peaks of 1100°F, down to 210°F, the maximum safe baghouse inlet temperature. A survey of existing blast furnace gas temperatures in the outlet flue showed that the normal range was as given in Table I. The obvious choices of cooling method were: 1— cool completely by the addition of tempering air; 2—utilize a heat exchanger; 3—cool by radiation; and 4—cool with water spray in conjunction with the admission of tempering air. The advantages and disadvantages of the various cooling methods were: Air Addition: To cool completely by the admission of tempering air involved tremendous volumes, Fig. 1. For example, to cool 1 lb of blast furnace gas at 450°F requires 1.84 lb of air at 80°F or 1.60 lb at 60°F. As it is necessary to design for peak conditions, it can readily be seen that volumes of tempering air in the order of 1,500,000 cfm would have to be handled. Using the normal design figure of 2.5 cu ft per sq ft of bag area, a baghouse installation comprising some 600,000 sq ft of filter cloth would be necessary. Such design requirements would be prohibitive, not only from a standpoint of capital expenditure, but also because of space limitations. Heat Exchanger: The utilization of a heat exchanger was given serious consideration. A horizontal tube unit using air as the medium to cool the required volume of blast furnace gas from 400" to 250°F was investigated. Cooling above 400°F would be done by water spray, and below 250°F by admission of tempering air. The estimated capital cost of such a unit was found to be prohibitive. From an operating standpoint, there was considerable doubt as to whether the soot blowing equipment provided would effectively keep the dust from building up on the tube surface. The performance of heat exchangers operating on dusty gas in other company operations had not been too favorable. Radiation Cooling: Although somewhat cumbersome, gas cooling by radiation from 'trombone' tubes or other similar equipment (cyclones) is employed in many metallurgical operations. Such an installation was also considered. However, calculations showed that an installation much larger than the space available would be required to handle the gas volume involved. For example, to cool 153,000 cfm of blast furnace gas from, say, 600' to 250°F (i.e., remove in the order of 58,500,000 Btu per hr with heat transfer rates varying from 1.1 Btu per sq ft per hr per OF for the higher temperature ranges to 0.88 Btu per sq ft per hr per OF for the lower ranges) would need a cooling area of some 175,000 sq ft.

Jan 1, 1953

By A. Raman, P. P. Singh

The constitution of the La-Rh system was studied by powder X-ray diffraction, metallopaphic, and differential thermal analysis techniques and an equilibrium diagram is presented. Eleven intermediate phases occur in the system and the crystal structural data for nine of them were determined. La3Rh crystallizes in an orthorhombic structure of undetermined type, whose unit cell is obtained by doubling the 'a; and 'c,,' edges of an FesC type unit cell. The other intermediate phases of the system are LarRh-3( undetermined structures also occur in the system. LaRh, undergoes a polymorphic phase transformation at 1240°C. LaRh3 and La2Rh7 also exhibit polymorphisnz. The phases Laah and LazRh7 melt congruently. The latter undergoes a eutectoid transformation into LaRh, and Rh at 1205°C. Laah3 is formed by a peritectoid reaction between Laah and La,Rh,,. The other Phases result from peritectic reactions between the liquid and the adjacent rhodium-rich phases. The intermediate Phases of the La-Rh system are compared with those of the La-Co and La-Ni systems. DURING the course of a detailed investigation to study the occurrence of CrB, FeB, A1B2, and related structures in the rare earth alloys it was found that much information is lacking for the rare earth noble metal systems. Although the structures of several rare earth alloys containing the noble metals at the AB and AB2 stoichiometries have been reported, the occurrence of related structures at other stoichiometries has not been studied. We have initiated a project to study the crystal structural features of selected rare earth-rhodium alloys and to map the equilibrium diagrams of representative systems with conventional methods. The results of our investigation in the La-Rh system are presented in this paper. Two phases were known in the La-Rh system. LaRh has the CrB-type structure.' LaRhz is a MgCu2-type Laves phase.z EXPERIMENTAL PROCEDURE Alloys weighing less than 1 g were prepared from commercially pure lanthanum (99.9 pct +), supplied by Lunex Company, Pleasant Valley, Iowa, and rhodium (99.92 pct +), supplied by Engelhardt Industries, Newark, N.J., in a conventional arc melting furnace under argon atmosphere. The buttons were turned upside down and remelted three times to insure homogeneity in the samples. Since negligible loss of material was encountered during melting, a chemical analysis of the alloy buttons was not undertaken. Powder specimens for X-ray diffraction studies in the as cast state were then prepared. The buttons were wrapped in thin molybdenum foils and homogenized by heating in vacuum at suitable high temperatures for more than 1 week. They were then broken into three or four pieces for annealing experiments. The pieces were wrapped in molybdenum foils and annealed at various temperatures in evacuated quartz capsules. The annealing was carried out for 2 hr at or above 1200°C, 1 day at temperatures close to llOO°C, 2 days at 1000°C, and for 1 week at temperatures below 1000°C. After annealing the alloy pieces were again broken and powder specimens for X-ray diffraction were prepared. The powders of the lanthanum rich alloys with more than 80 at. pct La were prepared by filing. The filings were sealed in molybdenum tubings and stress-relieved at 600°C in vacuum. It was not deemed necessary to stress-relieve the powders of the other alloys, since the alloys were very brittle and were ground easily. POWDER X-RAY DIFFRACTION X-ray diffraction photographs of powders (-325 mesh size) of the alloys in the as cast and annealed states were prepared in a Guinier-de Wolff focussing camera with copper K, X radiations. These patterns were studied to identify the stoichiometries and the crystal structures of the intermediate phases. The lattice parameters of the phases were calculated after minimizing the differences between the observed sin2 6 values, calculated from the diffraction angles 8, and the sin2 8 values, calculated using approximate lattice constants obtained from a few lines. These differences were minimized manually to less than 0.0005. The latLice constants are judged to be accurate to *0.005A for values less thp about 10A and to k0.01~ for values greater than 10A. The relative intensities of the lines were calculated using a computer program written by Jeitschko and Parthk.~ No attempt was made to refine the atomic positional parameters in the phases. METALLOGRAPHY The phase equilibria in the investigated alloys in the as cast and annealed states were also studied by metallographic examination. The polished specimen surfaces were etched with 10 pct picric acid in alcohol (alloys up to 25 pct Rh), concentrated picric acid (from 25 to 37.5 pct Rh), 2 pct nital (40 to 50 pct Rh), 10 pct nital (from 50 to 66.7 pct Rh) and with concentrated 48 pct HF for the other rhodium-rich alloys. Selected microstruture~ were then photographed using a Po-laroid Land camera. THERMAL ANALYSIS Differential thermal analysis of the alloys was carried out in DTA-668 Stone differential thermal ana-

Jan 1, 1970

By C. E. Lesher

THIS paper reports a study of the reactivity of 950°F and 1650°F cokes as measured by relative rates of reduction of iron oxides at temperatures up to 2200°F. Previous work cited shows general acceptance of the theory that reduction by carbon is a gaseous reaction, and that kind and character of carbon as well as particle size have measurable effect on the velocity of reaction. As will be shown, the data obtained in this study confirm those conclusions. The work was not designed to examine iron oxide reduction equilibrium, but if reaction velocity be defined as the speed with which "a reaction tends to approach conditions of equilibrium," the data here presented may be considered as a study of reaction rates, and the relative degree of reduction to metallic iron as the measure of reactivity. Three standardized combinations of Lake Superior brown iron ore with carbon were tested by similar procedures. One combination was a mechanical mixture of carefully sized high-temperature coke (1650°F) with the ore. The second was a mechanical mixture of the ore with Disco* obtained by carbonizing the identical coal at 950 °F. The third was an agglomerate prepared by carbonizing the coal and ore at 950°F, premixed in proportions to give as nearly as possible the same relative amounts of carbon and ore as the mechanical mixtures. This agglomerate, obtained by heating the finely divided ore (through 30 mesh) with coking coal through the plastic temperature range so as to form solid aggregates, gives a product in which the oxide particles are impregnated with, and intimately bound together with low-temperature coke. The agglomerate-—ore-Disco—was most active in oxide reduction; the mechanical mixtures of Disco and ore next in order, with coke the least reactive. General Discussion: Carbon exists in many forms and it is well known that the form or nature of the carbon used in reduction of oxides is related to the critical temperature of reduction. Sugar carbon, charcoal, and lampblack are forms of carbon that will reduce oxides at lower temperatures than high-temperature coke, and coke will, in turn, give a lower critical reduction temperature than graphite. There have been many investigations of this characteristic of carbons. Johnson' reported a difference of 130°F (70°C) in the critical reduction temperature of zinc oxide as between charcoal 1891 °F (1033°C) and Acheson graphite turnings 2021°F (1105°C) with zinc oxide. Bodenstein2 using charcoal and coke, found a difference of 138°F (77°C) comparing an experimental figure of 2066°F (1130°C) for coke and 1928°F (1053°C) for charcoal, in the reduction of zinc oxide. He concluded that this is very marked and observed that the "type of carbon merely raises or lowers the temperature at which rapid reaction takes place." Comparing the effectiveness of types of carbon in reduction of zinc oxide, it was found that a "brown coal coke" gave 97 pct zinc elimination at 1832°F (1000°C), as compared with 48 pct with "hard coal coke."' A wide range of metallic oxides was studied by Tammann and Sworykin,4 who found that the temperature at which decomposition of oxides begins depends on the nature of the carbon used. Carbon in the form of graphite, lampblack, and sugar carbon was investigated. Sugar charcoal will reduce Fe2O3 to Fe3O4 at 842°F (450°C) as compared with 1112°F (600°C) for coke, according to Meyer." Direct reduction of iron oxides by charcoal begins at 1382°F (750°C), but "first becomes intense" at 1652°F (900°C), whereas with coke, direct reduction begins at 1742°F (950°C), and "first becomes appreciable" at 2012°F (1100°C).6 he total reduction of the sample under certain conditions when heated in a current of CO with charcoal was about 100 pct for limonite and about 77 pct for magnetite. Using coke under the same conditions, the respective percentages were 75 and 47. In a study of processes for sponge iron7 by the Bureau of Mines, the conclusion was reached that a low-temperature char from noncoking subbituminous coal is the most satisfactory solid reducing agent. In a critical study of zinc smelting from a theoretical viewpoint Maier8 concluded that the reduction is by CO, that the reaction between ZnO and CO is intrinsically more rapid than the subsequent reduction of CO2 by C, which is limited by diffusion rates, which in part effectively limits the smelting process. Maier said that the operation is improved with the activity of the reducing carbon. An active carbon, he said, is one maintaining a low CO, content in the retort. Reactivity of Carbon: One form of carbon is more potent in reducing oxides than another. A carbon that reacts faster than another at a given temperature is said to be more reactive. Reactivity is measured by several methods, using carbon dioxide, air, or steam as reactants.9 ebastian and Mayers" have developed a method for the determination of absolute reaction rates between coke and oxygen by a study of ignition points under certain conditions. These and other investigators have established the relative reactivity of types of carbon. Lignite, charcoal, bituminous coal, cokes in the ascending order

Jan 1, 1951

By C. E. Lesher

THIS paper reports a study of the reactivity of 950°F and 1650°F cokes as measured by relative rates of reduction of iron oxides at temperatures up to 2200°F. Previous work cited shows general acceptance of the theory that reduction by carbon is a gaseous reaction, and that kind and character of carbon as well as particle size have measurable effect on the velocity of reaction. As will be shown, the data obtained in this study confirm those conclusions. The work was not designed to examine iron oxide reduction equilibrium, but if reaction velocity be defined as the speed with which "a reaction tends to approach conditions of equilibrium," the data here presented may be considered as a study of reaction rates, and the relative degree of reduction to metallic iron as the measure of reactivity. Three standardized combinations of Lake Superior brown iron ore with carbon were tested by similar procedures. One combination was a mechanical mixture of carefully sized high-temperature coke (1650°F) with the ore. The second was a mechanical mixture of the ore with Disco* obtained by carbonizing the identical coal at 950 °F. The third was an agglomerate prepared by carbonizing the coal and ore at 950°F, premixed in proportions to give as nearly as possible the same relative amounts of carbon and ore as the mechanical mixtures. This agglomerate, obtained by heating the finely divided ore (through 30 mesh) with coking coal through the plastic temperature range so as to form solid aggregates, gives a product in which the oxide particles are impregnated with, and intimately bound together with low-temperature coke. The agglomerate-—ore-Disco—was most active in oxide reduction; the mechanical mixtures of Disco and ore next in order, with coke the least reactive. General Discussion: Carbon exists in many forms and it is well known that the form or nature of the carbon used in reduction of oxides is related to the critical temperature of reduction. Sugar carbon, charcoal, and lampblack are forms of carbon that will reduce oxides at lower temperatures than high-temperature coke, and coke will, in turn, give a lower critical reduction temperature than graphite. There have been many investigations of this characteristic of carbons. Johnson' reported a difference of 130°F (70°C) in the critical reduction temperature of zinc oxide as between charcoal 1891 °F (1033°C) and Acheson graphite turnings 2021°F (1105°C) with zinc oxide. Bodenstein2 using charcoal and coke, found a difference of 138°F (77°C) comparing an experimental figure of 2066°F (1130°C) for coke and 1928°F (1053°C) for charcoal, in the reduction of zinc oxide. He concluded that this is very marked and observed that the "type of carbon merely raises or lowers the temperature at which rapid reaction takes place." Comparing the effectiveness of types of carbon in reduction of zinc oxide, it was found that a "brown coal coke" gave 97 pct zinc elimination at 1832°F (1000°C), as compared with 48 pct with "hard coal coke."' A wide range of metallic oxides was studied by Tammann and Sworykin,4 who found that the temperature at which decomposition of oxides begins depends on the nature of the carbon used. Carbon in the form of graphite, lampblack, and sugar carbon was investigated. Sugar charcoal will reduce Fe2O3 to Fe3O4 at 842°F (450°C) as compared with 1112°F (600°C) for coke, according to Meyer." Direct reduction of iron oxides by charcoal begins at 1382°F (750°C), but "first becomes intense" at 1652°F (900°C), whereas with coke, direct reduction begins at 1742°F (950°C), and "first becomes appreciable" at 2012°F (1100°C).6 he total reduction of the sample under certain conditions when heated in a current of CO with charcoal was about 100 pct for limonite and about 77 pct for magnetite. Using coke under the same conditions, the respective percentages were 75 and 47. In a study of processes for sponge iron7 by the Bureau of Mines, the conclusion was reached that a low-temperature char from noncoking subbituminous coal is the most satisfactory solid reducing agent. In a critical study of zinc smelting from a theoretical viewpoint Maier8 concluded that the reduction is by CO, that the reaction between ZnO and CO is intrinsically more rapid than the subsequent reduction of CO2 by C, which is limited by diffusion rates, which in part effectively limits the smelting process. Maier said that the operation is improved with the activity of the reducing carbon. An active carbon, he said, is one maintaining a low CO, content in the retort. Reactivity of Carbon: One form of carbon is more potent in reducing oxides than another. A carbon that reacts faster than another at a given temperature is said to be more reactive. Reactivity is measured by several methods, using carbon dioxide, air, or steam as reactants.9 ebastian and Mayers" have developed a method for the determination of absolute reaction rates between coke and oxygen by a study of ignition points under certain conditions. These and other investigators have established the relative reactivity of types of carbon. Lignite, charcoal, bituminous coal, cokes in the ascending order

Jan 1, 1951

By Samuel H. Dolbear

THE value of a mine is basically dependent on its capacity to yield profits. Since the ore must be mined, treated, and sold, some of it in various future years. there is a risk involved as to future costs, selling price, and working conditions. It cannot be expected that the economic condition existing at the time of valuation will continue unchanged for long periods in the future. During the past 20 years, mineral production in the United States has been conducted under a changing economy in many respects more exacting than that applied to other businesses. There have been increased production incentives, technical aid, exploration of privately owned mineral deposits by government at federal expense, and liberal loans for development and equipment, with risk partially assumed by government.. Some of these benefits have been counterbalanced by price ceilings, consumption controls, and stimulation of competition from foreign producers who have been offered the same advantages extended to American operators. For the present, mines will operate under a government policy directed toward reducing federal aid and control. The tenure of this change will depend upon future elections and the status of foreign relations. War and threat of war are now of the most vital significance to the mineral industries. Other factors which influence cost of production, markets, and price of mine output might be classified as Acts of God or Acts of Government. In some countries expropriation and the difficulty of exporting earnings or investment returns are risks that must be considered by foreign capital. Recognizing that this retards American investment in foreign countries, the Mutual Security Agency offers insurance against such expropriation and guarantees the convertibility of capital and profits. Since it is impossible to predict with certainty either cost of production or selling prices of metals for long periods, some assumptions must be made as to profits in the future. The basic assumption must be that the price of the company's product will vary in proportion to changes in operating cost. There is often a lag in this reaction, however, for prices of minerals are generally more sensitive to declines and less sensitive to increases than are costs. This reflects in part the resistance of labor to downward wage revision and a corresponding alertness in realizing its share of price advances. Some labor contracts include automatic adjustments to metal prices. Notwithstanding the complexity of the, problems involved and the difficulty of weighing their effect on value, such risks may be appraised with reasonable accuracy and a rate of earnings adopted that is compatible with the risk. It is, of course, possible to revert to a yardstick of value such as the commodity dollar, which has been advocated from time to time, but while revaluation in 1933 disturbed public confidence, the theoretical gold dollar continues to be the standard of greatest stability. Its gain or loss in purchasing power is reflected ultimately in cost of production and selling price of the mine product. At present 35 dollars are allocated to one ounce of gold. Measurement of Risk In the application of the Hoskold and most other formulae, a yearly dividend rate commensurate with the risk involved is set aside out of annual earnings. If the risk is great, this rate may be 15 to 25 pct of the amount invested. The remainder is placed in a sinking fund invested in safe securities such as high grade bonds or conservative equities, and the interest or dividends from these securities are added to the sinking fund. The sum of these sinking fund payments and the compounded interest at the end of the mine life is taken as the value of the mine. Admittedly the decision as to the size of the risk rate is the most difficult element in valuation and one requiring the most exacting consideration. It is necessary to look years ahead in an effort to determine future costs, market prices, demand, competition which may develop, including that of substitutes, and other influences common to the mine and to the region in which it is situated. Another phase of risk is the enactment of unfavorable legislation, taxes, and what appears to be an alarming spread of nationalization and expropriation. Capital is sometimes borrowed from the government to finance strategic production. Such loans may be collectable only out of production and involve no liability otherwise. Valuation in these cases must recognize the effect of such a reduction in liability. Offsetting some of these risks are the possibilities of mechanization and other cost-reducing discoveries, improvements in mining and treatment methods, new uses for minerals and metals, and normal growth of markets. In this paper, the terms risk rate, dividend rate, and speculative rate are synonymous. Safe rate and redemption rate are also used interchangeably. These alternatives are used here because they are commonly found in the literature on mine valuation. In Michigan, the State Tax Commission has long employed a risk rate of 6 pct in its valuation of iron mines. There the outline of reserves is well established and operating costs and conditions are based on adequate experience. The following comment on rates appears in the report of the Minnesota Interior commission on Iron Ore Taxation submitted to the Minnesota Legislature of 1941.1 Most engineers agree that 7 percent for the specu-lative rate is "an absolute minimum". C. K. Leith in

Jan 1, 1954

By Amitava Gangulee, Michael B. Bever

The effects of changes in short-range order on some thermodynamic, electrical, and mechanical properties of the silver-rich Ag-Mg solid solutions have been investigated. The heats of formation at 273°K of several alloys after two different thermal treatments were measured by liquid metal solution calorimetry. Their electrical resistivities were measured at temperatures ranging from 4° to 773°k. Tensile tests and microhard-ness measurements were carried out at room temperature. An effective short-range order parameter and an effective interaction energy are defined. The measured changes in the properties are interpreted in terms of these quantities. The short-range order parameter is evaluated separately from calorimetric and X-ray data; the results are in fair agreement. Increasing short-range order lowers the resistivity of- the silver-rich Ag-Mg alloys but does not measurably affect the temperature dependence of the resistivity. Short-range order increases the yield stress of these alloys but does not affect the ultimate tensile stress. Changes in the effective short-range order parameter independently obtained from measured changes in the heat of formation, resistivity, and yield stress are in fair agreement. THE thermodynamic, electrical, and mechanical properties of solid solutions have been investigated as functions of composition in many alloy systems, but the effects of configurational variables, such as short-range or long-range order, on these properties have received much less attention. The silver-rich terminal solid solutions in the system Ag-Mg are well-suited for the investigation of the effects of order. The composition of these solid solutions may be varied over a range extending to about 27 at. pct Mg.1 Appreciable short-range ordering is likely to take place in these solid solutions; the degree of short-range order can be varied by suitable thermal treatments. In the alloy Ag3Mg long-range ordering is possible.2 This paper is primarily concerned with the effects of short-range order on some thermodynamic, electrical, and mechanical properties of the silver-rich Ag-Mg solid solutions.-The long-range ordering transition is the subject of a concurrent paper.3 1) EXPERIMENTAL PROCEDURES 1.1) Preparation of Specimens. Ag-Mg alloys containing up to 26.4 at. pct Mg were prepared by melting 99.99 pct pure Ag (obtained from Baker Chemical Co.) and 99.99 pct pure Mg (obtained from Eastman Chemi- cal Co. or Johnson Mathey & Co.) in graphite crucibles under molten potassium chloride. The solidified ingots were homogenized at 823°K for 10 days in evacuated Vycor capsules. A surface layer 6 in. thick was then removed by machining. The ingots were swaged into rods (2.5 mm diam) which were drawn into wires (1.0 mm diam). The wire specimens were annealed at 773°K for 24 hr in vacuum and either quenched into iced brine or cooled to room temperature over a period of 15 days. The average grain diameter (obtained from the linear intercepts) was about 0.1 mm. 1.2) Calorimetry. The heats of formation of the alloys were measured in a tin solution calorimeter as the difference in the heat effects of alternate additions of samples of an alloy and the mechanical mixture of its component elements. The additions were made from 273°K to the bath at about 623°K. The heat effect on addition of the alloys was approximately 5.5 kcal per g-atom. The procedure and the method of calculation have been described.4 1.3) X-Ray Diffraction. Short-range order parameters of two alloys were calculated from diffuse scattering intensities,' obtained with briquettes made from powdered specimens. A GE-XRD 5 diffractometer with filtered copper radiation was used. The absolute intensities were based on calibrations with paraffin. 1.4) Resistivity Measurements. The electrical resistivities were measured by a potentiometric method in which the potential drop across the specimen was compared with that across a standard resistance. For measurements below room temperature, the specimens were immersed in liquid helium (4°K), liquid nitrogen (78°K), dry ice and trichloroethylene (195°K), or ice and water (273°K). Measurements above room temperature were made on specimens held in a furnace under helium or in vacuum. The resistivity measurements were reproducible to ±0.5 pct or less. 1.5) Mechanical Tests. Tensile tests were carried out at room temperature with a Tinius-Olsen XY elec-tromatic Universal testing machine. Wire specimens (nominal gage length 1 in.) were used. The strain was measured with an extensometer, which had a sensitivity of 4 x 10-5; the strain rate was 10-3 min-1. Microhard-ness measurements were made with a square-pyramid indenter and a 100-g load.11 2) RESULTS AND DISCUSSION All measurements were made on two parallel sets of specimens, one quenched and the other slowly cooled from 773°K. The reported values are the averages of at least three measurements. In the range of magnesium concentration substantially below that of the composition Ag3Mg, quenched alloys have less short-range order than slowly cooled alloys. As the magnesium concentration approaches that of Ag3Mg, slow cooling develops long-range order. Quenching sup-

Jan 1, 1969

By K. M. Myles

The vapor pressure of palladium over a series of Rlz-Pd alloys has been measured by the torsion-effusion method. The thermodynamic properties of the alloy system at 1575=K have been calculated from the vapor pressure data. The activities and the free energies of formation exhibit large positive deviations from ideal behavior. The enthalpies of formation are endother-mic. The entropies of formation are positive and larger than the ideal entropy of mixing. All of the thermodynamic properties suggest that a strong tendency toward phase separation exists in the solid solutions. The possible origin of the phase instability and the various factors that influence the thermodynamic properties are discussed. RECENT studies of the thermodynamic properties of alloys of palladium with nontransition elements have indicated that a significant contribution to the enthalpy of formation is related to the redistribution of the conduction electrons upon alloy formation.'-' The present work was undertaken to ascertain the importance of this contribution in Pd/transition-metal alloys. The Rh-Pd system was chosen for this investigation for several reasons: 1) The thermodynamics of the system were unknown. 2) Rhodium and palladium are completely soluble at high temperatures; below 1118OK the solid solution becomes immiscible.', 3) The difference in magnitude between the vapor pressures of rhodium and palladium permitted the use of an existing effusion apparatus. 4) Additional information was known about the alloy system that would facilitate the interpretation of the thermodynamic results. EXPERIMENTAL PROCEDURE The thermodynamic properties of the Rh-Pd alloy system were calculated from the vapor pressure of palladium over solid palladium and over several solid Rh-Pd alloys. The vapor pressure was measured by means of the torsion-effusion apparatus that has been described previously. In this method, an effusion cell is suspended from a tungsten filament inside a high-temperature furnace. Two orifices are located eccentrically such that the effusion of the vapor creates a rotational torque in the filament. The angle of rotation is directly related to the total vapor pressure within the cell. As the vapor pressures of rhodium and palladium are approximately five orders of magnitude apart," the total vapor pressure was considered to be effectively equal to the equilibrium vapor pressure of palladium. The effusion cells were made from high-purity alumina since auxiliary experiments indicated that essentially no reaction occurs between alumina and solid Rh-Pd alloys. Unfortunately, because the orifices were irregular, an accurate calculation of the Free- man-Searcy correction factors" could not be made. The constants were determined in an independent experiment where the vapor pressure of copper, as measured in the alumina cell, was compared with an accurate value of the vapor pressure, which had been determined previously.4 Depletion of palladium from the surfaces of the specimens was minimal as the deflection of the cell remained constant, for at least 15 minutes, at each of the experimental temperatures. Lattice parameter measurements of the postrun alloys also indicated that no changes in the composition of the surfaces had occurred. The alloys were prepared by arc melting the requisite amounts of the 99.99 pct pure elements. The four most palladium-rich alloys were remelted in a levita-tion furnace since complete melting of the components had not occurred in the arc furnace. All of the alloys were subsequently homogenized at elevated temperatures in sealed alumina thimbles. After heat treatment, the alloys were analyzed chemically and were in essential agreement with the nominal compositions. The thermal histories and nominal compositions of the alloys are given in Table I. Lattice parameters of the heat-treated alloys were computed, by means of the method described by Mueller et a1. ,I2 from X-ray diffraction powder patterns obtained with filtered copper radiation in a 114.6-mm-diam Straumanis-type Debye-Scherrer camera. The results, which are tabulated in Table I, exhibit a slightly greater negative deviation from Vegards' law than the values reported by Raub et al.13 The diffraction lines were sharp and well-resolved and thus indicated that the alloys were homogenous. RESULTS The logarithms of the individual values of the vapor pressure of palladium were fit, by the least-squares method, as a linear function of the reciprocal of the absolute temperatures. The constants of the equations are given in Table I along with the temperature range over which the data was accumulated. The latent heat of vaporization at 298.15"K for pure palladium, calculated by the third-law method,14 showed no systematic temperature dependence. The average value of 88,920 * 20 cal per g-atom agrees favorably with the average of the results obtained in the most reliable previous investigations.15"19 The activities of palladium were computed from the vapor pressure data at 1525', 1575", and 1625OK. Consistent with the mass spectrometric study of the atomicity of palladium vapor,lg the vapor was assumed to be monoatomic. The activities of rhodium were determined by integrating the Gibbs-Duhem equation with the aid of the a function.20 In the calculations, the activities of the pure solid metals were assigned the value of unity. From the activities, the partial and integral free energies, entropies, and enthalpies of formation at 1575° K were computed; they are assembled in Table 11.

Jan 1, 1969

By E. P. Whittemore

Experience with the ASC multipoint gas lift system was obtained in Colonia zone of the West Montalvo field near Oxnard, Calif. The wells in this pool produce from depths varying from 10,500 to 12,000 ft. Oil gravity is generally 14 to 15' API with a few extremes of 12 and 20" API. Some salt water is produced which causes some very viscous emulsions. Viscosities at 150F (which is the approximate wellhead temperature) vary from 5,000 to 100,000 SSU. Most of the production is by gas lift, although a few wells are produced by rod and hydraulic pump. About half of the gas-lift wells are on continuous flow and the remainder are on intermittent lift using large, ported, pilot-operated valves for single-point transfer of gas from casing to tubing. Gas-liquid ratios vary from about 6 to 10 Mcf/bbl of gross fluid lifted. Wells are produced to a 450-psi trap system. The following remarks will be confined to intermittent lift only, since this is the type of lift which has been achieved with the ASC valve system. The maximum gross fluid which has been produced by single-point intermittent lift is about 350 B/D in 3-in. tubing and 200 B/D in 21/2-in. tubing with gas-liquid ratios of approximately 7 to 9 Mcf/bbl. Some design changes could reduce this ratio. The ASC multipoint system has provided production as high as 480 BOPD in 21/2-in. tubing with gas-liquid ratios just under 4 Mcf/bbl. To be able to apply the multipoint system, it is recommended that a detailed explanation be obtained concerning transition-point pressure and stabilizer setting—what its significance is to the string design, how it may work for or against the operation of the well, how it is related to tubing sensitivity and how it affects the unloading operation. The unloading operation may only be of academic interest in a technical paper, but to the production foreman, unloading and setting the valves in operation is a very real problem and should be understood in detail. One item touched lightly in the paper was the unloading valve. This valve controls the maximum pressure at which the well can be operated. When lifting heavy viscous fluids, it is most important to set this valve for the maximum possible realistic operating pressure at the surface. If the well lifts easily, it is simple to set the ASC valves at a lower operating pressure and the unloading valve will remain closed; but if the well happens to be heavier to lift than anticipated, it may be desirable to operate on the unloading valve itself and use all the energy obtainable at the bottom of the hole. In the Colonia pool very heavy wet-gas gradients are experienced due to the viscosity of the liquid and the dense mist which is left behind a slug of fluid. There are many combination strings of 3- and 21/2-in. tubing. This aggravates the wet-gas gradient problem and provides wet-gas gradients of about 50 to 70 psi/1,000. An advantage which multipoint lift has provided is increased slug efficiency through better maintenance of pressure under the slug and decreased fall back as the slug passes up the tubing. By using multipoint injection, wet-gas gradients have been reduced to about 30 psi/1,000. This has reduced bottom-hole operating pressure and given a production increase. The ASC valve is not a simple device. It's operation is difficult to understand, and it must be understood to be used efficiently in gas-lift design. Operating problems are difficult to diagnose—whether they be caused by the fluid lifted, valve malfunction, lift gas rate, or operating pressure. Calculations and reasoning are required to find out what is causing the problem. Inherent in the ASC valve is the inability to create large pressure differentials across a slug. Large differentials may be required to overcome the inertia of very viscous fluid as it is being accelerated in the bottom of the hole. This is tied back to the design of the unloading valve and is one reason for the importance of setting the unloading valve for the highest possible operating pressure. ~u; to the narrow spread the ASC valves provide, it is impossible to cycle slower than about 24 cycles/day on choke control. If small production of 150 BOPD and less is expected, a surface time-cycle controller will be required if the most economical operation is to be achieved. To achieve a satisfactory operation, the operator must keep a record of any changes made in the operating pressure of the ASC valves. Anything which may cause changes in casing pressure in excess of the stabilizer setting will change the valve operating pressure, and if this is not noted from daily inspection of the well casing-tubing pressure recorder charts, the operator will lose control of the well. Significant results can be achieved using ASC valves; however, considerable knowledge is required to design with them, and attention to detail is required for satisfactory field operation.

Jan 1, 1965

By A. A. Collins

When we speak of high copper on a lead blast furnace we think in terms of 4 to 5 pct, or. any lead charge carrying over 1 pct. Any copper on charge will produce its corresponding troubles such as lead well, extra slag losses, drossing problems, and the working up of the dross. This is indeed a very interesting subject and one that used to give the old-time lead metallurgists such as Eiler, Hahn and lles many worries, not so much in the actual operation of the hlast furnace but in the working up of the copper. When the American nletallurgists commenced with the American rectangular-shaped lead blast furnace in the 1870's and got away from the reverberatories such as were in use in Germany and other parts of the world, they went to greater tonnages, as 80 to 100 tons per day in comparison to the 20 to 30 tons per day in the other processes. With the greater tonnages along with insuficient settling capacity, the silver losses in some cases were increased. Hence the lead-fall was low, for there were no leady concentrates in those days to assist the metallurgist to gain lead or an absorber for the precious metals; and in some cases copper sulphides were added intentionally to the charge to produce a copper matte to lessen the silver losses through the dump slag. The operators in those days thought that where some copper was always present in the lead ores the copper should not enter into the reduced lead and alloy with it. This, by the way, is just the reverse of our present-day practice, when we try to put all of the copper into the blast furnace lead and to remove the same through the drossing kettles. Therefore the furnace was operated to produce a certain amount of matte or artificial sulphides, since, due to the great affinity of copper for sulphur, any copper present would enter the matte almost completely. Thus, the lead bullion produced was practically free from copper. The products of the furnace were metallic lead or lead bullion, containing 05 to 95 pct of the lead and about 96 pct of the silver which were in the ore—a lead-copper-iron matte which contained nearly all the copper in the ore and the slag, the waste product. In the United States, up through the year 1092, we find the small furnace 100 X 32 1/2 in. with 12 tuyeres, some 6 on each side, plagued with a small amount of poorly roasted sulphides— either from heap or hand roasters that produced matte. This matte was roasted and if poor in copper was returned for the ore smelting. Otherwise it was smelted either alone or with additions of rich slags or argentiferous copper ores, the products being lead and a highly cupriferous matte, the latter being subsequently worked up for its copper. The lead metallurgists kept trying and improving on furnace and roasting equipment designs until we find blalvin W. Iles constructing at the old Globe Plant at Denver what came to be the modern furnace. That is, in 1900 he built a furnace of 42 in. width by 140 in. at the tuyeres with a 10 in. bosh and a 16-ft ore column. This type has been more or less standard to the present time, though modified in width and length to meet the demand for large tonnages and improvements in structural details. In 1905 at Cananea, Mexico, Dwight and Lloyd developed the present down-draft sinter machine that has meant so much in producing a well-processed material for the lead blast furnace. In 1912 Guy C. Riddell came forth with double roasting at the East Helena Plant of the American Smelting and Refining Co., which removed the "zinc mush plague." Incidentally, with the introduction of double roasting, which most lead plants were forced into after 1924, when lead flotation came into its own, less matte or no matte was produced. When this stage arrived, the copper was forced into the dross and the casting of lead at the blast furnace lead-wells was stopped. In plants with a fair copper carry 1 pct or better on the blast furnace charge, the lead wells became inoperative once the production of matte stopped. The copper drosses clogged the lead wells and even with bombing, either water or dynamite, the operators could not keep them open. Thus, the lead wells were abandoned in some plants, such as at the El Paso and Chihuahua smelters of the American Smelting and Refinillg Co., and all lead taken out through the first settlers. The elimination of sulphur, espccially sulphide sulphur, from the blast furnace charge and the nonproductiori of matte resulted in a great saving of tinie, energy and equipment in the recirculation of the copper, With the copper content in the dross and dross-fall ranging in quantities from a few percent up to 60 pct, such as at El Paso, a drossing problem was created. As the old-time operators hated dross and buried the same in the shipping bullion, the modern metallurgists from 1925 on decided that with increasing dross-falls they would have to adopt the lead refiner's ideas of drossing kettles with subsequent treatment of the lead with a sulphur addition to have the shipping lead of 0.01

Jan 1, 1950

By N. F. Dyson, T. R. Scott

The iilzfluence of catalytic agents on the oxidation of ZnS has been studied under pressure leaching conditions, using a chemically prepared sample of ZnS which was substantially unreactive on heating at 113°C with dilute sulfuric acid and 250 psi oxygen. Nurnerous prospective catalysts were added at the ratio of 0.024 mole per mole ZnS in the above reaction but pvonounced catalytic activity was confined to copper, bismuth, rutheniuwl, molybdenum, and iron in order of. decreasing effectiveness. In the absence of acid, where sulfate was the sole product of oxidation, catalysis was exhibited by copper and ruthenium only. Parameters affecting the oxidation rate were catalyst concentration, temperature, time, oxygen pressure, and a7riount of acid, the first two being most important. The main product of oxidation in the acid reaction was sulfur, with trinor amounts of sulfate. An electrochemical (galvanic) mechanism has been suggested for the sulfuv-forming reaction, whereby the relatively inert ZnS is "activated" by incorporation of catalyst ions in the lattice and the same catalysts subsequently accelerate the reduction of dissolved oxygen at cathodic sites on the ZnS surface. Insufficient data was obtained to Provide a detailed mechanism for sulfate fornzation, which is favored at low acidities and probably proceeds th'rough intermediate transient species not identified in the preseni work. THE oxidation of zinc sulfide at elevated temperatures and pressures takes place according to the following simplified reactions: ZnS + io2 + H2SO4 — ZnSO4 + SG + HsO [i] ZnS + 20,-ZSO [21 In dilute acid both reactions occur but Reaction [I] is usually predominant, whereas in the absence of acid only Reaction [2] can be observed. Both proceed very slowly with chemically pure zinc sulfide but can be greatly accelerated by the addition of suitable catalysts, as suggested by jorling' in 1954. Nevertheless, an initial success in the pressure leaching of zinc concentrates was achieved by Forward and veltman2 without any deliberate addition of catalytic agents and it was only later that the catalytic role of iron, present in concentrates both as (ZnFe)S and as impurities, was recognized and eventually patented.3 It is now apparent that another catalyst, uiz., copper, may have also played a part in the successful extraction of zinc, since copper sulfate is almost universally used as an activator in the flotation of sphalerite and can be adsorbed on the mineral surface in sufficient amount The importance of catalysis in oxidation-reduction reactions such as those cited above has been emphasized by various writers and Halpern4 sums up the situation when he writes that "there is good reason to believe that such ions (e.g., Cu) may exert an important catalytic influence on the various homogeneous and heterogeneous reactions which occur during leaching, particularly of sulfides, thus affecting not only the leaching rates but also the nature of the final products." Nevertheless relatively little work has appeared on this topic, one of the main reasons being that sufficiently pure samples of sulfide minerals are difficult to prepare or obtain. When it is realized that 1 part Cu in 2000 parts of ZnS is sufficient to exert a pronounced catalytic effect, the magnitude of the purity problem is evident. An incentive to undertake the present work was that an adequate supply of "pure" zinc sulfide became available. When preliminary tests established that the material, despite its large surface area, was substantially unreactive under pressure leaching conditions, the inference was made that it was sufficiently free from catalytic impurities to be suitable for studies in which known amounts of potential catalytic agents could be added. The first objective in the following work was to identify those ions or compounds which accelerate the reaction rate and, for practical reasons, to determine the effects of parameters such as amgunt of catalyst, temperature, time, acid concentration, and oxygen pressure. The second and ultimately the more important objective was to make use of the experimental results to further our knowledge of the reaction mechanisms occurring under pressure leaching conditions. The fact that catalysts can dramatically increase the reaction rate suggests that physical factors such as absorption of gaseous oxygen, transport of reactants and products, and so forth, are not of major importance under the experimental conditions employed and an opportunity is thereby provided to concentrate on the heterogeneous reaction on the surface of the sulfide particles. As will appear in the sequel, the first of these objectives has been achieved in a semiquantitative fashion but a great deal still remains to be clarified in the field of reaction mechanisms. EXPERIMENTAL a) Materials. The white zinc sulfide used was a chemically prepared "Laboratory Reagent" material (B.D.H.) and X-ray diffraction tests showed it to contain both sphalerite and wurtzite. The specific surface area, measured by argon absorption at 77"K, varied between 3.9 and 4.6 sq m per g. Analysis gave 65.0 pct Zn (67.1 pct theory) and 31.9 pct S (32.9 pct theory). Other metallic sulfides (CdS, FeS, and so forth) used in the experiments were also chemical preparations of "Laboratory Reagent" grade. Samples of mar ma-

Jan 1, 1969

By I. R. Kramer

The effect of the specimen diameter, d, on the flow stress, cra of polycrystalline aluminunz (99.997) was studied. The increase in the flow stress could be accountedfor by the increase in the surface layer stress, with decreasing specimen diameter. Both , and a, were found to be proportional to For the smaller-dianzeter specimen (< 0.033 in.) at strains less than aboul 0.1, the work hardening of the surface layer was greater than that associated with the bulk of the specimen. At higher strains the work hardening due to the bulk appears to be independent of the specimen diameter. THE increase in the strength of metals with decreasing diameter is well-known; however, an adequate explanation for the cause of the size effect is still lacking. The earliest systematic investigation of size effect appears to be that of Onol who reported that for aluminum monocrystals the resistance to slip at low strains increased as the specimen diameter decreased. A change in the stress-strain curve beyond 0.001 strain was not found. However, Suzuki et a1 .&apos; reported for monocrystals of a brass and copper having diameters in the range of 2 to 0.12 mm that the entire stress-strain curve was raised as the specimen diameter was decreased. The effect of size was most apparent when the diameter of the specimen was less than 0.5 mm. In the discussion of this paper Honey-combe reported a size effect in copper crystals as large as % in. diam. These results are in agreement with those of paterson3 and Garstone et al.4 While the majority of the investigations on size effects was conducted in terms of the variation in the diameter of the specimen, several investigators studied the influence of the specimen geometry. For example, Wu and smoluchowski 5 reported that in aluminum monocrystals the slip system was a function of the specimen dimension in the slip direction. King-man and Green 6 studied the influence of size on the compressive stress-strain relationship of aluminum monocrystals when the ratio of length to diameter was constant. Their specimen diameters ranged from to & in. For specimens oriented for single slip the critical resolved shear stress for the smaller-size specimens increased with decreasing diameter. No effect was observed in the large-size specimens. Specimens having an orientation near the corners of the stereographic triangle did not exhibit a size effect. Apparently, the increase in strength with decrease in the diameter of the specimen is a general phenomenon and has been observed in a brass |T and cadmium as well as in aluminum and copper.&apos; In a series of investigations (for example Ref. lo), it was shown that during deformation a surface layer was formed which imposes a back stress, a,, on the moving dislocations. It is reasonable to predict that this surface layer stress, as, should be a function of the specimen diameter and could possibly account for the flow stress size effect. In fact, experimental evidence will be presented to show that this is the case; i.e., the increase in flow stress with decreasing size is equal to the increase in the surface layer stress, as, with size. In addition, data will be presented on the variation with size of and a* where is the back stress associated with the generation of dislocation obstacles in the bulk of the specimen and a* is the net effective stress acting on the mobile dislocations. A limited investigation was carried out on gold specimens to determine the influence of an oxide film. EXPERIMENTAL PROCEDURE The aluminum specimens were prepared from -in. bar stock (99.997 pct purity). The 0.350- and 0.150-in.-diam specimens were machined directly from the bars while the specimens having a diameter of 0.033, 0.020, and 0.015 in. were prepared by swaging and drawing to 0.04 in. and electropolishing almost to final size. The specimens were prepared with a 2-in. gage length. The specimens were annealed in vacuum (-10-4 Torr) at 350°C for 8 hr. The grain diameter of the specimens in the various specimen diameter groups was 0.08 ± 0.02 mm. Gold specimens of two diameters, 0.14 and 0.03 in., were prepared in a similar way and annealed at 650°C for 8 hr. The grain diameter of the gold specimens was 0.2 mm. After annealing the specimens were electrochemically polished to the final size and tested in an Instron tensile machine at a strain rate, E&apos;, of 10- 3 per min. While it was possible to determine the surface layer stress, a,, in the larger-size specimens by measuring the difference, Aa, between the stress before unloading the specimens and the initial flow stress after removal of the surface layer as outlined in detail in Ref. 10, this method is not applicable for small wires because of the difficulty in obtaining a sufficiently accurate measure of the diameter. The values at the various strains were therefore determined by measuring after the specimen had been annealed at 35°C for 4 hr. It has previously been shown" that the two methods give the same results for a provided that the annealing temperature is low enough to affect only the surface layer and not the dislocation barriers in the bulk of the specimen. For the gold specimens a treatment at 150°C for 16 hr was found to be satisfactory for the determination of by the low-temperature annealing method. EXPERIMENTAL RESULTS Determination of a,, and a,. The stress-strain curves for the various diameter aluminum specimens, plotted in terms of the logarithms of the true stress, and true strain, are given in Fig. 1. These curves represent the average data taken from at least ten specimens at each size. Over the range of strains investigated the curves follow the empirical equation

Jan 1, 1968

By L. C. Brown, C. St. John, C. C. Sanderson

The diffusion rate in Cu-Te couples is very sensitive to compressive stress, with a load of 20 psi making a significant difference to the width of the diffusion zone. At zero stress, two phases appear in the diffusion zone (Cu4Te3 and CuTe). Under compressive loading the third stable phase (Cuz Te) also appears, and its thickness increases progressively with increasing stress. The results are explained on the basis of an incipient Kirkendall porosity which restricts the transfer of atoms from the copper into the diffusion zone. DURING a study of the Kirkendall effect in Cu-Te couples prepared by clamping together the two components, it was found that the diffusion-zone width and shape in the plane of contact were not reproducible. Although the stresses involved in clamping are not normally sufficiently high to affect diffusion rates, preliminary tests established that the Cu-Te system is particularly stress-sensitive. The phase diagram for the system Cu-Te given in Hanssen1 shows that there is practically no solid solubility at either end of the phase diagram. Many areas of the diagram are not fully substantiated, but there appear to be three intermediate phases: Cu,Te—hexagonal in structure, having a grey luster; Cu4Te3—a tetragonal defect structure, having a red-purple luster; CuTe—orthorhombic in structure and having a golden-green luster. The existence of a fourth phase, the X phase at 37 at. pct Te, is considered doubtful. The composition ranges of the three stable phases are small, and are not accurately known. The phase diagram changes little with temperature up to 305°C, at which temperature a polymorphic transformation takes place in Cu2Te. The nature of the Cu-Te phase diagram indicates that the diffusion zone in a Cu-Te couple would consist of a series of layers of intermediate phases. The relative thickness of any one phase will depend on its diffusion coefficient and composition range.&apos; In this type of diffusion couple it is often found experimentally that some phases are not visible at all in the diffusion zone due either to a small diffusion coefficient or to a restricted composition range.3 Since the composition ranges of the phases in Cu-Te are not known, it is not possible to determine diffusion coefficients in this system from a knowledge of the phase thicknesses. Several investigations have been carried out to determine the effect of compressive stress on diffusion rates in multiphase systems. Diffusion couples of Ni-A1 have been investigated by Storchheim et al.4 and by Castleman and Seigle.5 Two phases (ß and ?) appear in the diffusion zone under zero stress and the thickness of both phases is progressively reduced with increasing stress. According to Storchheim et al.4 a stress of 25,000 psi reduces the thickness of the diffusion zone by 50 pct. In a-brass—?-brass couples the thickness of the 0 phase formed in the diffusion zone was reduced by 20 pct at a stress of 20,000 psi.6 In other investigations the compressive load has been observed to increase the width of the diffusion zone. In A1-U, several investigators3,8 have found the width of the whase UA13 to increase with stress. According to casileman,8 the rate of formation of UA13 at 520°C is 75 pct faster at a stress of 20,000 psi as compared with a stress of 2500 psi. In Cu-Sb the effect of stress is greater than in the other systems described. According to Heumann9,10 only one phase (y) appears in the diffusion zone at a stress of 500 psi, but at a stress of 850 psi two phases (y and k) are present. If a diffusion couple containing both y and k phases is annealed at a low stress level, the y phase grows at the expense of the k phase. EXPERIMENTAL The diffusion couples were prepared from electrolytic copper bar stock with a nominal purity of 99.92 pct and from tellurium of 99.7 pct purity. The tellurium proved difficult to machine because of its brittleness and a technique was developed for casting the tellurium into a graphite slab mold and spark-machining specimens from this slab. Both the copper and tellurium were produced in the form of discs 2 in. diam by approximately 1/4 in. thick with surfaces ground flat to 3/0 emery paper. The diffusion apparatus is shown in Fig. 1. Auni-axial compressive stress was applied to the system through a simple lever system. A stainless-steel rod actuated by the lever arm lay inside a stainless-steel tube. The diffusion couple lay on top of the steel rod, and pressure was applied to the couple between the rod and a plug welded into the center of the tube. To ensure a uniform stress across the couple, a hemispherical boss and cup were used to transmit the load to the diffusion couple. A 400-w tube furnace with a uniform hot zone 3 in. long slid around the stainless-steel tube and maintained the assembly at temperature. A thermocouple situated 3 in. from the specimen operated a proportional temperature controller which maintained the specimen temperature constant to ±2°C. Most diffusion runs were carried out at 250C although a few tests were made at other temperatures in the range 235° to 300°C. The specimens were inserted and removed with the furnace at operating temperature, and took only 2 min to reach diffusion temperature—a time small compared with the total diffusion time. All the diffusion experiments were carried out in a hydrogen atmosphere, since consistent results were obtained in hydrogen and nitrogen atmospheres and in

Jan 1, 1967

By W. A. Backofen, D. L. Holt

Push-pull fatigue tests have been carried out at 4.2°K, 77oK, and room temperature on two poly crystalline materials of widely different stacking-fault energy (?): pure copper (? - 70 ergs per sq cm) and the Cu-8 wt pct A1 alloy (? - 2.8 ergs per sq cm). Constant stress-amplilude was imposed and measurement was made of the plastic-strain amplitude (ep) at saturation. Lives extended from 104 to 106 cycles. Designating lives at the various temperatures by NRT, N77, and N4.2. the ratios N77/NNT and N4.2/N77 ranged from 3.5 to 18 under the condition of common Ep . Metallo-graphic examination revealed different crack morphology in Cu-8 Al fatigued at room temperature, and at 77" and 4.2oK. At room temperature, cracks lay in or near grain and lain boundavies; at 77o and 4.2oK. cvacks were transcrystalline. Tests on single crystals of Cu-8 A1 showed that such a change in the cracking mode in polycrystallitle material accounted for a factor of- about 3.25 in N77/NRT . The longer life at lower tewperatztre (conslant cp) has heels attributed to two deuelopinents: a reduced production of the dislocation tangles and subgrain boundaries which serve as paths of rapid cracking, and suppression of oxygen chetni-sorption at the crack tip It was concluded that in both materials the luller accounted for an extension of the life at 4.2oK beyond that at room temperature by a factor of 15. XV ECENT experiments on the fatigue of Cu-A1 alloys in the so-called high-cycle range (greater than lo4 cycles) have emphasized the importance of stacking-fault energy (y) as a quantity affecting crack propagation rate and fatigue life.1,2 It was found in comparisons at essentially fixed plastic-strain amplitude that crack growth rate decreased by a factor of about 5 over the composition range from copper (? - 70 ergs per sq cm) to Cu-8 wt pct Al (? - 2.8 ergs per sq cm). The argument was made that, when stacking-fault energy is high, cross slip and climb are favored, so that dislocation tangles and/or subgrain boundaries form more readily under cyclic loading. Since the boundaries and tangles act as paths of rapid crack propagation ,3, 4 life is shortened as a result. However, when stacking-fault energy is reduced (as by alloying), cross slip and climb become more difficult, with the result that substructure formation is retarded and growth rate is also reduced. A purpose of the present work was to investigate the substructure effect in relation to temperature. As temperature is lowered, ? is varied only slightly (if at all), but decreased thermal activation can interfere with cross slip and climb. Thus substructure formation could be curtailed and life increased. Fatigue life in the high-cycle range is also known to be strongly influenced by environment. Working with copper, Wadsworth and Hutchings observed that life in a vacuum of 10-8 mm Hg exceeded life in air by a factor of 20.5 They isolated oxygen as the agent that furthered cracking. While the details are still unclear, a requirement in any mechanism of oxygen-accelerated cracking is that there be chemisorption at the crack tip. That could prevent welding on the compression half cycle,= interfere with reversal of slip,1, 6 or aid in breaking metal-metal bonds at the crack tip.5&apos;7 In the work being reported here, temperature was lowered by immersion in liquid nitrogen and helium, which also served to reduce both the oxygen concentration and chemisorption rate. A possible effect upon life, i.e., a lengthening, had to be recognized. Several researchers have determined fatigue lives at low temperatures presenting their results in the form of stress amplitude (S) vs cycles in life (N) curves.8-11 Such curves reflect, primarily, the fact that metal is strengthened by lowering temperature; effects of substructure and changing environment tend to be masked. The difficulty can be overcome by comparisons based on identical plastic-strain amplitudes, and in the present work the dependence of life on both plastic strain and stress amplitude was established. EXPERIMENTAL Materials. The principal materials were polycrystal-line copper (? - 70 ergs per sq cm)" and the Cu-8 wt pct Al alloy (? - 2.8 ergs per sq cm),I3 the latter being near the limit of solubility of aluminum in copper and having, therefore, the lowest stacking-fault energy in the CU-Al system. Specimens were machined from 0.118-in.-diam cold-swaged rods of high-purity (99.999 pct) copper and the Cu-8 Al alloy, the latter produced initially in a graphite boat by induction vacuum melting a mixture of 99.999 pct Cu and 99.99 pct Al. The machined specimens were annealed to produce mean grain diameters of about 0.070 mm in copper and 0.190 mm in the alloy. Specimen dimensions are given in Fig. 1. Values of the tensile yield stress, ultimate strength, uniform strain (determined by the Considgre construction), and reduction of area, for both materials at 4.2oK, 77oK, and room temperature, are listed in Table I. The tensile apparatus in which these results were obtained has already been described.14 Apparatus. Specimens were fatigued in push-pull with a machine that is illustrated schematically in Fig. 2. The specimen is first soldered into the top grip (1) with Woods metal, and the grip is then screwed into the inner tube (2) which is connected to the drive rod of the Goodmans vibration genera-

Jan 1, 1968

By Hansheinz Portisch, Harold Margolin

A surface expansion was found to occur sometime after etching in Ti-A1 alloys containing 9.5 to 12.5 wt pct Al. The structure formed, grew, and disappeared with tzrrze. The surface expansion was followed by microscope observations and interferometric and lattice parameter measurements. Activation energy measurements for the growth of the "expansion structure" and chemical analysis indicated that the phenomenon occurred as a result of hydrogen pzckup during etching. It is proposed that hydrogen initially enters octahedral sites of Ti3Al coherent with a Ti and later shifts to the tetrahedral sites. It is postulated that expansion occurs when hydrogen enters the tetrahedral sites. The expansion structure disappeared, it is proposed, because of diffusion of hydrogen from the surface into the body of the alloy and because of loss of coherency of Ti3Al. In examining Ti-A1 alloys, Ence and arolinl observed markings on the surface of specimens. These markings did not appear after electropolishing only, but rather appeared only after etching. The markings appeared to grow as a function of time after etching and later seemed to disappear. Although the markings had some similarity to precipitates, showing, frequently, a Widmanstatten type of arrangement, the observation that other microstructural markings continue to be seen within the new structure suggested that it was actually not a precipitate. The source of this structure was unknown and an attempt was made in the present investigation to develop some understanding of its nature. It has been labeled expansion structure. 1) EXPERIMENTAL PROCEDURE A) Alloys. Alloys in the range 6.5 to 14.5 wt. pct A1 were studied. Bars, 4 in. sq, forged from Bureau of Mines (73 Bhn) titanium consumably arc-melted 4-lb ingots,&apos; as well as 50-g arc-melted buttons of desired aluminum contents were used. The 50-g buttons also used Bureau of Mines titanium (73 Bhn) and aluminum of 99.99 pct purity. Buttons containing up to 8.5 wt pct A1 were hot-rolled from a furnace at 900&apos; . Those with higher aluminum contents were hand-forged on a titanium anvil, and heated with an oxygen-hydrogen torch in the region of 1200" to 1300°c. Frequent reheating kept the samples at the desired temperature range. After a reduction of about 30 pct, the samples were water-quenched. To eliminate any contamination picked up either during hot rolling or forging, at least 1 mil of the surface of the sample was taken off. B) Heat Treatment. Prior to heat treatment all alloys were vacuum-annealed to remove hydrogen. Samples were annealed at 900&apos; until a vacuum of 10&apos;5 mm Hg was established. After this treatment, the samples were wrapped in molybdenum sheet and heat-treated in argon-filled quartz capsules, which were broken under water or iced brine at the conclusion of the heat treatment. All heat treatments under dynamic vacuum were performed in a rapid-quench furnace. This consisted of a molybdenum-lined quartz tube attached to a vacuum system and through a stopcock to a beaker of water. At the completion of the heat treatment the vacuum stopcock was closed, the furnace shut off, and dropped below the quartz tube. Then immediately the inlet stopcock was opened and water admitted until the tube was filled. The steam formed was allowed to escape through the inlet stopcock. This method was used in heat treatments up to llOO°C. C) Metallography. Specimens for metallographic examination were ground, then electropolished using a Disa Electropol machine with a perchloric acid electr01te. Specimens were etched with R-etch.3 A standard etching time of 3 min was used, with the specimen being agitated during immersion. D) Sample Preparation for X-ray Analysis. Samples 0.2 to 0.5 mm in diam were produced from heat-treated rods which were turned to 2 mm diam on a lathe and then rotation-etched. An etchant consisting of 1 pt HF, 7 pt HN03, and 12 pt HzO was satisfactory. With the rod rotating in a vertical position at 50 to 100 rpm, a needle with uniform dimensions could be obtained. Care had to be taken to insure that the rod was at the center of rotation, otherwise cavitation developed. If a small unevenness developed, it was possible to grind it off with a fine emery paper. E) X-ray Diffraction. All X-ray work was done on a North American Phillips X-ray diffraction apparatus and a Jarrell Ash microfocus X-ray unit. The Phillips unit was used with a copper target and nickel filter. The Jarrell Ash unit was fitted with a cobalt target and iron filter. For the Phillips unit 35 kva and 20 ma were used, whereas for the microfocus unit with the 100-p fixed-focus gun 40 kv and 1.5 ma were used. It was found that alignment of cameras on the Jarre11 Ash unit was very critical. The X-ray beam contains an intense area which is not the beam center. The cameras were aligned with the intense region by monitoring the beam coming out of the camera with a Geiger counter. Adjustments were made until a maximum intensity was obtained. A Phillips diffractometer with a Brown chart recorder furnished some of the lattice parameter data. The divergence slit up to 80 deg 28 was I deg; above 80 deg, a 4-deg opening was used, while the scatter slit was1 deg and the receiving slit had a 0.003-in. opening. The general scanning rate was 1 deg per min, while peaks of special interest were rescanned at -j deg per min. For elevated-temperature X-ray diffraction a Uni-cam High Temperature Camera with a film diameter

Jan 1, 1969

By M. R. Geer Olds, H. F. Yancey

THE increase in the number of coal-cleaning plants employing dense-medium processes occurring since 1946 is especially interesting when viewed historically. Both sand and magnetite were introduced as material for heavy mediums at about the same time, sand in the Chance process in 1921 and magnetite in the Conklin process in 1922, but from that point on their records diverge. The Chance process enjoyed a steady growth from its inception, whereas no additional magnetite plants were built in the United States for over 20 years. Then, following the close of the World War 11, magnetite was again introduced, this time with marked success. During the following years some 47 plants employing magnetite medium were built. This rapid growth of dense-medium cleaning has been concurrent with widespread adoption of full-seam mining on one hand and a return to a more competitive market on the other. At a time when changing mining practice has provided cleaning plants with dirtier coal and changing market conditions have simultaneously demanded a cleaner product, the industry has through necessity turned to improved preparation. The inherently greater sharpness with which dense-medium processes can separate coal from impurity is thus helping to hold the line against ever-increasing mining costs and at the same time assisting materially in retaining badly needed markets. Although dense-medium cleaning unquestionably offers a distinct advantage when the washing problem is difficult, other methods can provide almost equally high efficiency when the coal is easy to wash. Moreover, fine coal cannot yet be treated by heavy medium in a proved process, although the Driessen cyclone is in the pilot-plant stage. Most of the present types of dense-medium equipment have been in use only a few years, and the dearth of information in the literature concerning their performance characteristics is entirely understandable, Nevertheless this information is necessary if the process is to be intelligently applied to individual cleaning problems. Without data on the efficiency of a process in a particular type of separation, it is difficult to assess the advantage to be expected from it. Similarly, the role of particle size in heavy-medium separation is important in some cases, yet there is little published information on this aspect. To mention only one more of the numerous points on which essential information is lacking, the bearing of medium characteristics on performance has been discussed only in qualitative terms. It was with the hope of providing information on some of these points that the Bureau of Mines built a dense-medium pilot plant for cleaning coal at its Northwest Experiment Station in Seattle in 1950. The plant has been operated continuously since that time, and over 50 runs have been made on 7 coals exhibiting a wide range of washability characteristics. An idea of the magnitude of this work will be gained from the fact that examination of the plant products has involved some 600 float-and-sink separations and about 2500 ash determinations. A laboratory pilot plant is especially well adapted to investigate many aspects of performance because close control over test conditions can be exercised and because a large number of tests can be made rapidly. On the other hand, factors such as consumption of medium and other cost items can be investigated satisfactorily only in a commercial plant. Actually, the two forms of investigation should be complementary, with the laboratory work pointing the way for confirming tests in commercial units. Pilot Plant The dense-medium pilot plant employed for this work comprises a 24x30-in. drum-type separating vessel, a 12-in. densifier, a 12-in. magnetic separator, a 26-in. x 9-ft vibrating screen, and the necessary pumps and conveyors for handling materials. Arrangement of these units corresponds with the flowsheet used in most commercial plants, except that a thickener is not provided for the feed to the magnetic separator. Coal and refuse discharge from the separating drum to the vibrator, which is divided longitudinally down the center. Medium draining through the first 3 ft of the screen is recirculated directly to the drum. Sprays on the middle 3 ft of the screen rinse medium from the products, and the last 3-ft section is for dewatering. Dilute medium from the rinsing and dewatering sections is pumped to the magnetic separator, where magnetic solids are recovered. These are pumped to the densifier, from which they return to the medium-drainage sump by gravity through a demagnetizing coil. The drum-type separating vessel is a scale model of a commercial unit. Feed enters axially at one end of the drum just below the surface of the bath, and float material overflows through a circular opening at the other end. Particles sinking to the bottom of the bath are picked up by lifting flights bolted to the inner wall of the drum, elevated out of the bath, and sluiced to the vibrating screen. Baffles suspended in the bath prevent float material from entering the sink-lifting flights. About 8 gpm of medium is used to sluice the feed into the drum. An additional 15 to 24 gpm, depending upon operating conditions, is added through two pipes dipping into the bath behind the baffle on the side where the sink-lifting flights enter the bath. The bath available for separation is 2 ft long and 13 in. wide, giving an area of 2.08 sq ft. Depth of bath from the surface to the top of the sink-lifting flights, measured vertically below the axis, is 6 in.

Jan 1, 1954

By Jacques Steininger, Robert E. England

Single crystals of ZnTe and ZnTe1-,Sex with x up to 0.13 have been grown from the elements by temperature gradient solution zoning using excess tellurium as a solvent. Best results have been obtained with charges with the compositions 45/55 at. pct Zn, Te, for ZnTe and increasing amounts of selenium for ZnTe1-xSex. The temperature in the molten zone was maintained at about 1070°C with a gradient of about 10°C per cm. Chemical analyses of quenched ZnTe ingots show tellurium concentrations in the molten zone as high as 70 pct with concentration differences across the zone of 1 to 2 at. pct Dark dots which are observed by transmitted light microscopy in as-grown crystals can be removed by annealing in zinc vapor at 900 C. INTEREST in wide band gap semiconductors has led to a new study of ZnTe and ZnTel-xSex crystal growth. ZnTe is the only II-VI compound with a wide band gap (2.3 ev) that can be made p type with low resistivity. Attempts to make it n type with low enough resistivity to be useful for p-n junctions have so far been unsuccessful.1 ZnSe has a band gap of 2.65 ev but can be made n type only. However, ZnTel-xSex solid solutions with x as low as 0.36 have been made both highly n and p type2 with a minimum band gap around 2.12 ev3 at room temperature and appear to hold the best promise for efficient injection electroluminescence in the visible. ZnTe has the lowest melting point of the zinc chal-cogenides (1295°C) and consequently attempts have been made to grow crystals from both the liquid and the vapor phase.4 Complicated apparatus is required for growth from stoichiometric melts because of the high vapor pressures of the elements at the melting point of ZnTe and because of the problem of quartz devitrification. Small crystals have thus been grown in high-pressure equipment by Fischer5 and by Narita et a1.6 with pressures of the order of 50 atm of argon to prevent excessive evaporation from the melt. Large crystals of ZnTe can be obtained by growth from the vapor phase4 but they often present numerous dislocations and inclusions. An improvement in the quality of vapor- grown ZnTe crystals was reported by Albers and Aten7 by equilibration of mixtures of small crystals with compositions lying on either side of the solid single-phase field at fixed temperature. The same technique was later applied by Aten8 to the growth of ZnTe1-xSex crystals with less than 1 pct inhomo-geneity. Because of the higher liquidus temperatures of the solid solutions and the high vapor pressure of selenium, previous attempts to grow ZnTel-xSex from the melt have been limited and unsuccessful.9 The phase diagram of the Zn- Te system is reproduced in Fig. 1, based on data from Kobayashi10 and Kulwicki.11 Carides and Fishher12 have reported lower liquidus temperatures on the tellurium-rich side, but their data would require confirmation. The liquidus temperature on the tellurium-rich side decreases rapidly with increasing tellurium concentration and the Te2 vapor pressure over the liquidus also decreases accordingly.&apos;3 The decrease in liquidus temperature and vapor pressure therefore makes it possible to use conventional apparatus if there is a sufficient excess of tellurium in the melt. Single crystals of ZnTe have thus been grown by Kucza,14 in a modified Bridgman technique, from solutions containing up to 60 at. pct of Te by lowering unsupported quartz ampoules through a temperature gradient at about 1200°C. Under these conditions, the phase diagram indicates that the entire charge is initially molten. Crystal growth can therefore proceed by normal freezing and rejection of excess tellurium into the melt. The modified Bridgman technique has several major limitations. Because of the rejection of excess tellurium into the melt during freezing, the melt composition and the temperature at the growth interface vary continuously. They tend to follow the liquidus until the eutectic which is very close to pure tellurium (447°C, >99 pct Te). Since the solidus composition also varies with temperature,15 crystals grown by this method are inhomogeneous. They present small variations from stoichiometry which may affect their structure and physical properties. The simultaneous increase in tellurium content and decrease in melt temperature also combine to reduce the rate of diffusion of tellurium away from the growth interface, thereby causing constitutional supercooling and possibly dendritic growth. To minimize these effects, the initial melt composition is in practice kept relatively close to stoichiometry (less than 60 pct Te). This however limits the possibilities of operating at low temperatures and pressures. This paper describes a modified method of crystal growth by temperature gradient solution zoning (TGSZ) which is an adaptation of the temperature gradient zone-melting technique developed by pfann16 and of the traveling solvent method of Mlavsky and weinstein.I7 The TGSZ method now applied to the growth of ZnTe and ZnTel-xSex crystals is characterized by its very simple experimental arrangement and sample preparation technique. Unlike the modified Bridgman technique, there is no increase in the tellurium concentration in the melt and therefore it is possible to operate at lower temperatures and pressures. This method is also suitable for maintaining a constant temperature at the growth interface.

Jan 1, 1969

By G. R. Speich

The distribution of carbon and the type of substructure in iron-carbon martensites containing 0.02 to 0.57pct C has been studied in the as-quenched condition and after tempering at 25" to 700°C by using electrical resistivity, internal friction, hardness, and light and electron microscope techniques. in marten-sites containing less than 0.2 pct C, almost 90 pct of the carbon segregates to dislocations and to lath boundaries during quenching; in martensites containing greater than 0.20 pct C, appreciable amounts of carbon enter normal interstitial positions located far from defects. Tempering martensites with carbon contents below 0.20 pct at temperatures below 150°C results in additional carbon segregation to dislocations and to lath boundaries but no carbide precipitation whereas -carbide precipitation occurs in martensites with carbon contents exceeding 0.2 pct. Above 150°C, a rod-shaped carbide (either Fe3C or Hagg) is precipitated in all cases. At 400°C, spheroidal Fe3C precipitates at lath boundaries and at former aus-tenite grain boundaries. At 400" to 600"C, recovery of the martensite defect structure occurs. At 600" to 700°C, recrystallization of the martensite and Ost-waW ripening of the Fe3C occur. The effects of the carbon segregation that occurs during quenching and the subsequent substructural changes that occur during tempering on martensite tetragonality, hardness, and precipitation behavior are discussed. A mathematical analysis of carbon segregation during quenching is presented. RECENT studies of the strength of low-carbon martensitel-4 emphasize the importance of carbon segregation to the martensite lath boundaries and to the dislocations contained between them during quenching. Unfortunately, very few studies of the tempering of low-carbon martensites have been conducted, so the exact nature of this segregation is poorly understood. In fact, most early tempering studies5,6 were restricted to carbon contents greater than 0.20 pct. Moreover, these studies did not determine the amount of carbon segregated to the martensite substructure during quenching so that the initial state of the martensite was not established. Aborn7 studied the precipitation of carbide in low-carbon martensite during quenching but did not establish whether carbon segregation occurs prior to carbide precipitation, nor did he study the subsequent tempering sequence in detail. In the present work we have used electrical resistance and internal friction measurements, supplemented by electron transmission microscopy to establish the carbon distribution in as-quenched specimens. Specimens thin enough to avoid carbide precipitation (but not carbon segregation) were employed. The redistribution of carbon on subsequent tempering below 250°C was followed by measurements of elec- trical resistance. Additional studies were made on specimens tempered at 250" to 700°C to elucidate the overall tempering behavior of low-carbon martensites, including the formation of cementite and recrystalli-zation of the martensite. EXPERIMENTAL PROCEDURE Eight iron-carbon alloys with 0.026, 0.057, 0.097, 0.18, 0.20, 0.29, 0.39, and 0.57 wt pct C were prepared as 8-lb ingots by vacuum melting. Typical impurities in wt ppm were 40 Si, 20 Mn, 30 S, 10 P, and 10 N. These alloys were hot rolled to 3 in. plate at 1095°C) (2000°F). The hot-rolled plates were surface ground to remove scale and the decarburized layer, then cold rolled to 0.010 in. sheet. Specimens cut from the sheet were austenitized for 30 min at 1000°C (1830°F) in a vacuum tube furnace in which the pressure did not exceed 2 x 10-3 torr. Chemical analysis of specimens after austenitization indicated no decarburization at this pressure. Immediately before quenching, the furnace was filled with prepurified helium. The specimen was then pushed rapidly through an aluminum foil gasket, which sealed the bottom of the furnace, into an iced-brine bath (10 pct NaC1, 2 pct NaOH). The quenching rate at the M, temperature is about 104&apos;c per sec for 0.010 in thick specimens, as calculated from Newton&apos;s law of heat flow2 using a heat transfer coefficient of 25 ft-&apos;. This quenching rate is sufficiently high so that all the alloys transformed completely to martensite throughout the entire 0.010 in thickness and no carbide precipitation occurred in the martensite. All specimens were immediately transferred to liquid nitrogen after quenching and stored there until needed. Tempering below 250°C (480°F) was done in silicone oil baths thermostatically controlled to *;"C. Tempering above 250°C was done in circulating air furnaces or lead pots with the specimens contained in evacuated silica capsules. Electrical resistance was determined by measurement of the potential drop across both a standard resistance and the specimen, connected in series. All resistance measurements were made in liquid nitrogen (77K, -196°C) to minimize thermal scattering of electrons and thus maximize the contribution of impurity scattering to the resistance. Specimen dimensions were 5.10 by 0.19 by 0.025 cm. Although the precision in the electrical resistance measurements was +0.1 pct, the electrical resistivities could only be measured with an accuracy of +5 pct because of uncertainty in the specimen dimensions. Internal friction measurements were performed in an inverted pendulum apparatus at vibration frequencies of either 1.9 or 66 Hz. The specimen dimensions were 5.10 by 0.375 by 0.025 cm. Hardness measurements were made with a Leitz-Wetzlar microhardness machine with loads of 100 g. Specimens were examined by light microscopy after etching in 2 pct Nital and by electron transmission microscopy after preparation of thin sections by electrolytic thinning in a chromic-acetic acid solution.

Jan 1, 1970