Search Documents

By J. B. Newkirk

IN 1939 Bitter and Kaufmann1 suggested that iron, precipitating from a copper-rich, Cu-Fe solid solution, appears initially as coherent particles of r-Fe which transform to the body-centered-cubic form of iron when the alloy is cold worked. Since then there has been considerable discussion, supported only by indirect evidence, regarding the validity of the concept. For example, Reekie, Hutchison, and Hether-ington2 interpreted the changes in electrical resistance accompanying the aging of Cu-Fe specimens in terms of a coherent 7-Fe precipitate which transformed to the incoherent a-phase during long aging or cold working. Greninger- ound that Cu-Fe alloys which had been water quenched from 1050" and then held at 650°C for 3 hr changed from weakly to strongly ferromagnetic as the aged wire was subsequently cold worked. He also found diffraction lines corresponding to body-centered-cubic iron in Debye-Scherrer patterns given by aged and worked specimens but lines corresponding to only one face-centered-cubic phase in specimens which had been aged but not worked. Knoppwost,' and later Cech and Turnbull,5 found that aged Cu-Fe specimens showed a slight increase in ferromagnet-ism after they had be? cooled in liquid nitrogen. Very recently Denney6 followed the kinetics of the precipitation reaction as indicated by the saturation magnetization, hardness, and diffuse X-ray effects. The experimental results reported by all of the authors mentioned above are readily explained in terms of the Bitter and Kaufmann concept. However, most of the evidence is indirect when used to define the structural changes involved. It was the aim of the present investigation to determine the mechanism of precipitation of iron from a Cu-Fe solid solution in the light of available published information and with additional new and more direct experimental data. Experimental Method At 1060°C copper will contain up to 3 atomic pct Fe in equilibrium solid solution.7 The solvus slopes rapidly toward lower iron concentration, so that at 600°C only about 0.5 pct Fe remains in solution at equilibrium. Below the eutectoid temperature (850°C), the iron-rich phase in equilibrium with the copper-rich solid solution consists of body-centered-cubic a-Fe. Above 850 °C the equilibrium iron-rich phase is face-centered-cubic r-Fe. The alloy to be studied was made by melting electrolytic iron and OFHC copper by induction under vacuum in an Alundum-lined crucible. The metal was held molten for about 5 min, after which time the power was turned off and the crucible was tipped about 70" to promote directional solidification. The resulting ingot, containing 2.5 wt pct Fe by analysis, was clean, large grained, and free of gross segregation. Slices % in. thick were cut from the ingot, rolled to 1/8 in. in thickness, homogenized in hydrogen at 1060°C for 24 hr and, finally, quenched in cold water. Specimens for all subsequent tests were made from these slices. Squares measuring about 1 cm on a side were cut from the slices to make specimens for studying hardness and microstructure. Wires (0.020 in.) for the Debye-Scherrer survey were drawn from 1/8 in. sq rods which had been cut from the homogenized slices. Large crystals for observing diffuse X-ray diffraction effects were prepared by mechanically

Jan 1, 1958

By A. Heim, M. Gondouin

Invasion experiments were run on Berea sandstone cores to get laboratory measurements of resistivity and saturation profiles characteristic of water and oil sands invaded by mud filtrate. Injection rates were as low as 1.13 cm/D, and the cores were 30 to 36 in. long, cut parallel to the bedding planes. In the water-sand case, the resistivity profiles revealed the existence of an extensive transition zone between flushed and uncontaminated zones. In the linear geometry of the experiment, the width of the transition zone increased as the square root of the injected fluid volume. For the oil-sand case the core was prepared by displacing the formation water with kerosene to minimum water saturation. During the subsequent invasion experiment. oil saturation was measured directly by means of an oil-soluble radioactive tracer, and resistivity profiles along the core were taken at the same time. These data were interpreted in terms of an oil-water front, followed by a formation water bank, a zone of mixed waters, and finally, invaded mud filtrate near the borehole. Micro-fingering and capillarity seemed to affect considerably the resistivity profiles observed in the invaded oil-sand experiment. Beyond the regular conductive annulus or "low zone", it was found that a resistive "anti-annulus" could also be formed. As a result of these experiments, some simplified invasion profiles have been accepted and are being used in Grand Slam* interpretations. INTRODUCTION The importance of the mud filtrate-invaded zone in interpreting electrical logs has long been recognized.',* In trying to account for its effect, only very simple models of the resistivity profiles in the radial direction from the borehole have been used. In fact, most log interpretation charts have been based on resistivity models consisiting of two media of uniform resistivity (R, and R,) abruptly separated at the diameter of invasion. Such a clean separation of the media of different resistivities seems unrealistic, since flushing may not be perfect and may vary with radial distance into the formation.3** The nature of the transition zone, when it is within the radius of investigation of the surveying devices, may affect the log readings. Campbell and Martin' verified that a conductive annulus containing a high percentage of formation water may be formed when mud filtrate invades an oil-bearing sand. Interpretations which are to include the effect of such an annulus require the addition to the model of a conductive zone located at the outer rim of the invaded zone.' Using the Buckley-Leverett relations,6 aturation profiles may be derived, from which resistivity profiles can be calculated. Results of such computations by K. S. Kunz and J. H. Moran were given in a paper by Dumanoir. Tixier and Martin,7 and led to the construction of log interpretation charts which were based on a representation with three media of resistivities R, R0 and R1. Fig. 1 shows a schematic representation of a resistivity profile which includes an annulus. Campbell and Martin realized that, during the invasion of an oil sand, both capillarity and mixing would contribute to rounding of the profile shown in Fig. 1. Capillarity tends to draw some of the formation water from the annulus into the uncontaminated (Rt) zone, whereas mixing of the mud filtrate with formation water of the

Jan 1, 1965

By N. S. Stoloff, R. G. Davies

The annealing behavior of a heavily cold-worked FeCo-V alloy has been studied at temperatures both above and below Tc, the critical temperature for ordering. It was found that re crystallization and grain growth can take place below Tc in the ordered state and that, in agreement with results for fcc alloys, order retards grain growth. The activation energy for pain growth is -55 kcal per mole in the disordered condition; it was not possible to assign a value to the activation energy for grain growth below Tc because the degree of order is changing rapidly over the temperature interval investigated. Precipitation of an fcc y phase was observed upon annealing the cold-worked alloy at temperatures of 675°C and below. SINCE it is known that diffusion constants are greatly affected by long-range order,' it is not unreasonable to anticipate that order will influence the diffusion-controlled phenomena of recrystallization and grain growth. In the course of a study of strain aging of ordering alloys around the composition Ni3Fe Vidoz, Lazarevic, and cahn2 noted that a disordered cold-worked alloy annealed at a temperature T1 just below Tc will order but not recrystallize; Tc is the critical temperature for order. The same alloy annealed at a temperature T2 just above Tc, or an alloy of different (nonordering) composition annealed at either T1 or T2, will recrystallize after equivalent amounts of cold work. Initially Selisskii and coworkers,3,4 who examined a series of cold-worked and annealed bcc Fe- Co alloys, reported that alloys forming the B2 FeCo super lattice could not be recrystallized below Tc. However in a later paper5 it was shown that FeCo ordered alloys could be recrystallized below Tc. Thus the first question to be answered by the present investigation was whether or not a heavily cold-worked Fe-Co-V alloy could be recrystallized below Tc. When it was found that the alloy would indeed re-crystallize below Tc, the influence of long-range order upon subsequent grain growth was studied. EXPERIMENTAL PROCEDURE The grain-growth measurements were made upon FeCo-2 pct V wire of 0.031 in. diam; the alloy was the same as that used in an earlier study of the mechanical properties of FeCO-v.6 The wire was produced by cold swageing and drawing a rod 0.125 in. diam that had been quenched into iced brine from 850°C to disorder the alloy; the initial grain size was 0.05 mm. Rates of grain browth were measured after isother-mally annealing the wire in the temperature range 675° to 825°C; T, is -720°C. Grain diameters were measured on the transverse cross section of the wires. The line-intercept method of determining the grain diameter was used; conventional light photomicrographs were taken when the grain size was greater than 10 . Carbon replicas were produced and examined in the electron microscope if the grain size was less than Dislocation configurations after recrystallization anneals were studied by electron transmission microscopy of foils produced by cold rolling a 0.125-in.-thick strip of the quenched material to 0.012 in. The foils, after heat treatments similar to the wire samples, were thinned by electropolishing in a chromic-

Jan 1, 1967

By W. M. McKewan, R. G. Olsson

In order to improve the understanding of the iron oxide reduction mechanism, the rate of equal molar diffusion of hydrogen and water vapor was measured through disks of porous iron and alumina. The measuretneizts were made at atmospheric pressure at 800°, 900- , and 1000°C. It is shown tint the reduction of dense hematite pellets with hydrogen at these temperatures and at atmospheric pressure is to a great extent limited by gaseous diffusion between the bulk-gas phase and the iron-wustile interface. THE investigation of the reduction of iron oxides with hydrogen has been the subject of numerous papers. Although the effects of temperature, pressure, and gas composition on the rate of iron oxide reduction have been studied, the actual mechanism of the reduction process has not been definitely determined. As a means of improving the understanding of the mechanism, the rate of equal molar counterdiffusion of hydrogen and water vapor was measured through porous iron and porous alumina disks at reduction temperatures. The alumina was used as a basis of compari-son because its pore structure is homogeneous and independent of temperature. The porous iron was prepared by the reduction of dense hematite disks with hydrogen at the temperature of the subsequent diffusion experiment. The hematite disks were made from pellets that were identical to those used by McKewan1,2 in his study of iron oxide reduction with hydrogen. In these investigations the weight loss and rate of movement of the various interfaces were measured as a function of the reduction temperature and gas composition. With these reduction data and the presently reported diffusion data it is possible to determine the importance of H2-H2O transport between the bulk-gas phase and the Fe/FeO interface to the reduction of dense hematite. APPARATUS AND PROCEDURE A porous iron or alumina sample was held in the base plate of a sealed canister containing porous granular wustite, as illustrated schematically in Fig. 1. The canister was suspended from an automatic recording balance in a vertical tube furnace through which flowed hydrogen and water-vapor mixtures of known composition at atmospheric pressure (0.96 atm). Hydrogen from the gas stream diffused through the porous sample, reducing the wustite in the interior of the canister. The water vapor that was formed diffused back to the gas stream. The rate of diffusion was determined from the recorded weightloss data. The furnace, automatic balance, and gas-metering equipment have been described previously.2 The main body of the canister and the tubing extension were made of stainless steel while the base plate was made of high-purity iron. The main body of the canister was % in. in diam. It held approximately 6 g of porous granular wustite that was prepared by reducing 0.1- to 0.2-cm-diam specular hematite particles at 900°C with an H2-H2O mixture of a composition near the iron-wustite equilibrium value. The upper end of the 1/8-in.-diam tubing extension was sealed with a segment of plastic tubing and a tubing clamp. The temperature at the top of the furnace was sufficiently high so that no water vapor condensed inside the extension. In the experiments with porous iron, iron oxide samples were prepared from reagent-grade hematite that was pressed and sintered in a manner previously described.' The resulting pellets had a density of 5.15 ± 0.05 g per cu cm. Each pellet was centerless-ground

Jan 1, 1967

By Clark L. Corey, Bogdan Lisowsky

Electrical resistivity, X-ray line positions, degree of order, and microstructures have been investigated for Ni-A1 alloys near the Ni3Al composition. The results indicate that Ni3Al undergoes disordering between 1250oC and the mp; also supersaturated y, produced in y + y' alloys by gas quenching, is extensively ordered prior to y' (Ni3Al) phase separation. The latter reaction, if not both, must follow the cooperative phenomena model. Shifts in line position as a function of quench-indulced super satulration are shown. Lattice pavarneters of equilibriunz and nonequilibrium phases are given. THE objective of this investigation was to determine the mechanism and kinetics of the reactions which occur in Ni3A1 and hypostoichiometric Ni3A1 alloys. The results are of particular significance relative to pre-precipitation phenomena. Early work on Ni-A1 binary compositions near the Ni3A1 composition (13.6 wt pct Al) has been adequately reviewed by Hanssen,1 whose phase diagram is presented in Fig. 1. williams2 verified the suggestion made by Taylor and Floyd3 and others4 that y', Ni3A1, may precipitate coherently on (100) planes of the y phase (see Fig. 1 for phase nomenclature); he further suggested a two-step precipitation mechanism consisting initially of probably short-range ordering followed by actual precipitation of y'. The precipitation stage in low-aluminum hypo-eutectic compositions has been studied by a number of investigators;*"7 short-range order or "zone" formation have been suggested as explanations for various diffuse X-ray scattering effects. The ordering reaction in Ni3A1 alloys is characterized by a) a very rapid rate of ordering in nonstoi-chiometric compositions, b) absence of a disordered phase region for the stoichiometric compound, y', or Ni3A1, c) precipitation phenomena as a dominant aspect in hypoeutectic alloys, and d) an increase in elec-trical resistivity on ordering.' The latter two factors were found by Newkirk to characterize ordering in Co-Pt, for which an extensive and detailed analysis was made.' An electrical-resistivity increase on ordering has also been reported for cuAu3.10 PROCEDURE Ni-A1 alloys in the form of 1300-g chill-cast ingots were prepared by vacuum melting electrolytic nickel and high-purity (99.99 pct) aluminum. Very small heats prepared from high-purity carbonyl nickel, supplied through the courtesy of Dr. Goff of the Naval Research Laboratory, were used for comparison with the larger ingots and no differences were noted. The cast material was homogenized in purified argon for a minimum of 72 hr at 1200°C and water-quenched from 1350°C. Compositions studied are given in Table I. The 10 pct A1 alloy was both hot- and cold-rolled. X-ray superlattice line intensities and peak positions were obtained from -270 mesh filings, using CuK, radiation with a LiF crystal monochromat adjusted to receive both 01 and a2. One-degree slits and a 1/8 deg per min scan rate were used to record line traces. A standard tungsten powder, obtained through the courtesy of G.E. Research Laboratory, was used to calibrate line positions.

Jan 1, 1968

By J. Geertsma

In order to obtain a better insight into the pressure-volume relationship of reservoir rocks a theory of pore and rock bulk volume variations is presented. The theory is independent of the shape of the pores but is restricted to isotropic porous media built up of continuous homogeneous matrix material. The main conclusion obtained from this theory is that only three elastic constants and three viscous constants are required for describing pore and rock bulk volume variations if the porosity is explicitly introduced into the treatment. In addition, reasonable approximations are introduced for various types of reservoir rock, e.g., sandstones, limestones, and shales, which lead to further simplifications of the basic formulas. In consequence there is then a further reduction in the number of deformation constants which have to be determined experimentally. It is shown how measurements of these remaining deformation constants can be performed most conveniently. Finally the application of the theory to reservoir studies is discussed and the translation of experimental results obtained in the laboratory into reservoir behavior is considered. INTRODUCTION The decline of fluid pressure in connection with the withdrawal of fluid from an underground reservoir gives rise to a change in volume of both reservoir fluids and reservoir rock. The volume variation of the reservoir rock results in a decrease of both the pore volume and the total volume of the fluid-filled formation. Whereas the variation in volume of the reservoir fluids with pressure is usually known from PVT analysis, that in the volume of the porous medium is rarely measured, as it is considered of minor importance in reservoir engineering. Nevertheless, certain experimental results' suggest that in a number of cases the neglection of the variation in pore volume may introduce errors into material balance calculations of reservoirs producing above the bubble point. Only a few experimental results on the compressibility of porous rocks have been published. The compressibility of pure quartz and of calcite can be found in a paper by Adams and Williamson'. Botset and Reed' carried out some experiments on the compressibility of loose sands, while Carpenter and Spencer' measured the compressibility of a number of consolidated sandstones, which data were supplemented by Hughes and Cooke5. Hall' finally reported a number of experiments designed to study the influence of the porosity on the compressibility of oil-bearing formations, from which it appeared that, particularly in the low porosity range, the compressibility of the pore volume is important enough to be taken into account. Difficulties, however, arise in applying these experimental results to field cases. This is partly due to the fragmentary nature of the published data. Yet even if more complete data were available, the need for a theoretical background would be strongly felt. Such a background can be partially found in studies carried out by Biot,6,7 who published a theory of elastic deformations of porous materials and their influence on fluid displacement within the pores, by Lubinski8, who studied the stress distribution in an elastic porous medium neglecting pore compressibility, and by Gass-mann" who mathematically analysed the elasticity of packings of spheres. The contributions of Biot intro-duce a number of deformation constants which are impractical for reservoir rocks from an aspect of experi-mental determination. The theory developed by dass-mann is correct but difficult to read. It appeared, how-

Jan 1, 1958

By C. R. Clark, G. Swift, D. S. Roberts

The purpose of this investigation was to measure PVT behavior of various types and combinations of heavy hydrocarbon components from the paraffinic, naphthenic and aromatic classes where the relative proportions Of the various components were selected to approximate those of natural gas or gas condensate systems. Synthetic mixtures were used so that the compositions Of the various components could be measured accurately. n-Heptane, methylcyclohexane and methylbenzene were used to represent the paraffinic, naphthenic and aromatic components of the heavy fraction. In the mixtures studied, the heavy fraction composition was held constant at O. O5-mole lraction, the balance being methane except for one mixture where 0.10-mo1e fraction of an intermediate component, propane, was added. The PVT data for the mixtures were determined in a variable-volume, constant-mass apparatus at psuedo-reducedtemperatures from 1.84 to 2.00, over a pseudo-reduced pressure range from 2.3 to 12.0. The experimental results showed that, regardless of the type of heavy material (paraffinic, naphthenic, aromatic, or combinations thereof) mixed with methane or methane and propane, the compressibility factors at equal values of pseudo-reduced temperature and pressure varied by less than 2.2 percent. INTRODUCTION PVT data is used for natural gas and gas condensate fluids in determining reserves of reservoirs and performance of wells, in metering produced fluids, and in recombining samples for laboratory studies. While there are vast amounts of PVT data reported for natural gas and gas condensate systems from which useful correlations have been developed, ' the compositional analyses for these systems and the resultant correlations typically were made with components analyzed through some arbitrary carbon number, usually C6, with the residue reported as a lumped "heavy" fraction. The heavy fraction was stoichiometrically recombined on the basis of an apparent molecular weight to give the final compositional analysis. It is virtually impossible to make a systematic analysis of the effect that variation of the relative amounts of paraffinic, naphthenic and aromatic constituents of the heavy fraction of natural systems might have on PVT behavior. Because there is considerable latitude in the relative amounts of these constituents, one speaks of crudes or condensate liquids as being "paraffin base", etc. It is of interest to determine if changes in the relative amounts of these three types of hydrocarbons in the heavy fraction cause significant changes in PVT behavior. If so, steps should be taken to describe better the nature of the heavy fraction in PVT correlations. If not, more confidence can be placed in the correlations presently employed. DESIGN OF THE EXPERIMENTAL INVESTIGATION We attempted to determine if changes in the base of the heavy fraction would cause significant changes in the PVT behavior of gas or gas condensate fluids. Synthetic mixtures were used to enable us to systematically vary the base of the heavy fraction and to analyze accurately the fluids. We found that the heavy fraction of naturally occurring condensate systems seldom exceeds 0.05-mole fraction. Thus, the mole fraction of the heavy fraction in the synthetic systems studied was set arbitrarily at 0.05, to maximize whatever deviations in PVT behavior that might occur. Further, we judged that since the C7 hydrocarbons normally are present in greater quantities than higher carbon number hydrocarbons in naturally occurring systems, the use of n-heptane, methyl cyclohexane, and methylbenzene to represent the paraffinic, naphthenic, and aromatic species in the heavy fraction would be most appropriate. Finally, to enable us to compare our

Jan 1, 1970

By Robert T. MacMillan

Of all the mineral substances utilized by man, salt or sodium chloride has one of the longest and most varied histories. Because all animal life is descended from marine organisms, sodium and chlorine became necessary to life, and as sodium chloride meets requirements most readily, common salt has been essential to human and animal diets from earliest times. As civilization progressed, man learned to evaporate sea water and brines of saline lakes and springs to obtain salt, and gradually ceased to depend on the flesh of animals and the occasional salt outcrops or "salt licks" they frequented. He also learned that salt had a multitude of uses, particularly as a preservative of meat and other foods. The importance of salt in the minds of early men may be readily seen from many allusions in the Bible and other ancient writings. Expressions such as "not worth his salt," and "the salt of the earth" are deeply embedded in the English language. Salt has symbolized friendship, fidelity, purity, and hospitality. It has been used as currency; had religious significance; caused wars; and has been a favorite commodity for taxation. The English word "salary" stems from the Latin word for salt, in which Roman soldiers received part of their pay. Although salt today retains its dietary importance, it has thousands of other uses. Of each 100 pounds produced in the United States less than three pounds is for table use. The other 97 pounds goes for agricultural, industrial, and chemical uses. Fortunately, reserves of salt are enormous and reasonably well distributed on the face of the earth. The sea is an inexhaustible source of salt which may be had at prices which vary with climate and other factors. In addition, large underground salt deposits and many salt lakes, springs and playas are scattered throughout the world. Most countries have access to a salt supply, although some are more favored than others. Properties Crystallized sodium chloride or common salt is known as halite. Its molecular weight is 58.454 and it contains, by weight, 39.34 pct sodium and 60.66 pct chlorine. Alternate positions in the cubic lattice are occupied, respectively, by negative chloride and positive sodium ions; the crystal form is isometric. Crystallization from water produces concentric shells, and when broken, a crystal shows conchoidal fracture. Salt has a hardness of 2.5; its specific gravity ranges from 2.1 to 2.6 for rock salt and is 2.165 for the pure crystal. The refractive index is 1.554; it melts at 800.8 ± 0.5°C and boils at 1413°C. Its heat of fusion is 123.59 cal/ gram. Salt is transparent or translucent and highly diathermous. It is colorless when pure and has a vitreous luster. Salt containing traces of iron oxides has varying shades of yellow, orange, brown, pink, or red. The peculiar shade of red sometimes found in that produced by solar evaporation of sea water has been attributed to tiny organisms. Blue mottlings sometimes seen in halite crystals have been attributed to colloidal sodium. Salt is soluble in water to the extent of 35.7 parts per 100 parts of water at 0°C and 39.8 parts per 100 of water at 100°C. The small difference in solubility with increasing temperature is important in the economics of producing salt by evaporating brine. Salt has a negative heat of solution which is 1.281 kg-cal/ mole at 18°C in 200 moles of water.

Jan 1, 1960

By K. A. Svanstrom, W. R. Opie

Problems associated with deposition of titanium infused chloride baths using TiCl4 as a feed material are reviewed. A potentially workable cell design using Alumdum diaphragms is discussed. Problems inherent to diaphragm-type cells are emphasized and experiments described which led to the development of a cell without a diaphragm. INVESTIGATORS assigned the problem of developing a commercial electrolytic process for making titanium metal have found that they are faced with the difficulty of overtaking rapidly improving magnesium and -sodium reduction processes. The ultimate goal must be a simple process that can be conducted with low-cost raw materials in equipment that is inexpensive to build and operate. This paper deals with some work of a preliminary nature conducted by personnel of the Research Laboratories, National Lead Co., Titanium Division. Many others have reported on the general subject of depositing titanium from fused salt electrolytes. A partial bibliography is attached. PRIMARY CONCEPTS Anyone attempting to deposit titanium metal from fused chloride electrolytes using TiC14 as a source material is faced with at least the following problems: 1) Getting the titanium into solution in the bath. 2) Controlling oxidation and reduction reactions associated with multiple valency of titanium, which result in low electrical efficiency. a) Prevention of dichloride oxidizing to trichloride and trichloride to tetrachloride at the anode. b) Prevention of trichloride from being reduced only to dichloride at the cathode. 3) Prevention of metal formation away from the cathode thru disproportionation of titanium dichloride to satisfy the equilibrium. 3 TiCl2 == 2 TiCl3 Ti [I] 4) Protection of reduced chlorides in the bath from reaction with oxygen from the bath container or air. 5) Removing from the bath the deposited metal formed without allowing it to become contaminated with oxygen or nitrogen. 6) Selecting cell materials of construction which will not contaminate the metal product or cause cell inefficiencies. EARLY EXPERIMENTS The initial attempts made to electrodeposit titanium from fused chloride baths using TiCl4 as a source material indicated that TiCl4 was essentially insoluble in molten chlorides of alkali and alkaline earth metals. If, however, the TiCl4 was introduced close to a nickel cathode some metal could be formed and appreciable quantities of reduced chlorides would be present. These reduced chlorides reacted with any oxygen present in the atmosphere above the bath and would also diffuse quickly to the anode (graphite) where they would react with chlorine and be evolved as TiCl4. The net electrolytic efficiency of such a cell is essentially nil. The TiCl4 evolves from the anode at almost the same rate that it is introduced in the vicinity of the cathode although a small amount of titanium metal can be formed on the walls of the cathodic pipe. It becomes apparent from the operation of such a cell that: metal can be deposited on the cathode, although of small particle size and a nonadherent nature, and when reduced chlorides are present in the electrolyte, TiCl4 can be absorbed, probably by the following reactions: TiCl4 + TiC12 - 2 TiCl3 [21 2 TiCl3 + 2 faradays - 2 TiC12 + C12 [31 DIAPHRAGM CELLS These facts encouraged the development of cells containing diaphragms to prevent migration of reduced chlorides from the cathode area to the anode. Small-scale cells for process development are described by Alpert, Schultz, and Sullivan.20 A larger brick-lined cell incorporating internal heating by passing ac through the bath is shown in

Jan 1, 1960

By A. W. Ruff

In the last ten years large gains have been made in the field of blasting. These gains have been both in the theoretical and in the practical application of explosives. One of the most publicized changes in the practical application of commercial explosives is the now-prevalent use of ammonium nitrate and fuel oil. The new water-compatible mixture of ammonium nitrate and TNT should also have a large field of application. Most of the theoretical gains have been concerned with the actual rock breakage obtained with explosives. In the last ten years, large gains have been made in the field of blasting. These gains have been both in the theoretical and in the practical application of explosives. One of the most publicized changes in the practical application of commercial explosives is the now prevalent use of ammonium nitrate and fuel oil. The new water-compatible mixture of ammonium nitrate and TNT should also have a large field of application. Most of the theoretical gains have been concerned with the actual rock breakage obtained with explosives. EXPANDING-GAS-BUBBLE THEORY There has been an outstanding change in the conception of how an explosive produces rock failure. The early theory which explained rock breakage was correct for some of the first force-producing agents such as quicklime. When a drillhole was filled with quicklime and water added, the material expanded and steam was generated. The expanding material and the steam exerted a slowly increasing pressure on the sides of the drillhole. The force broke the rock by splitting. Because a great quantity of gas was produced by the deflagration of gunpowder, the same process of the gas pressure splitting the rock was assumed to take place. Even after 80 years of use, the rock-breaking action of all high explosives was thought to be caused entirely by the expanding gas bubble which tore and split the rock. Fig. 1 shows a vertical section through an exploding spherical charge of high explosive. It illustrates the early theory which attributed the entire breakage to the expanding gas bubble. The basic idea of this theory is that the breakage started at the explosive charge and progressed toward the free face. REFLECTED-WAVE THEORY me expanding-gas- bubble theory has gradually been replaced by the reflected-wave theory. The reflected-wave theory explains rock failure by explosives in the following manner: The enormously high gas pressure in the drillhole produces fracturing of the rock on the sides of the drillhole. The fracturing around a 1 1/2-in. diam drillhole is usually confined to an area with about a 6-in. diam. In the fractured area, the pressure of the gas is reduced until the force on the walls is no longer capable of fracturing the rock. Although the gas pressure does not continue to fracture the rock, the pressure imposes a high impact stress on the wall rock. In addition, a pressure or seismic pulse is produced in the rock. The pulse is probably entirely a compression pulse when originally produced in the rock. But, with distance, part of the energy of the compression pulse is transformed into a tension pulse which follows the compression pulse. The explosive charges and burdens used in conventional mine blasting are such that the tension pulse of the original wave is probably too small to be considered in a practical evaluation of the theory. The compression pulse is transmitted through the rock with no associated fracturing.

Jan 1, 1961

By Randolph C. Specht

A two year study was made of the waste disposal of the pebble rock phosphate industry. Solid slimes are impounded in large settling areas and the process water is re-used. Clear effluent was not found to be toxic to fish or animal life in field tests or in controlled experiments. Survey: The pebble rock phosphate mining and washing operations in Florida (fig. 1) are along the river basins of the Alafia to the west and the Peace to the east. The elevation of the area varies between 40 and 170 ft above sea level. Effluents from the operations find their way into one of the two river systems (fig. 2), the Peace River which flows into Charlotte Harbor and the Alafia into Tampa Bay, both along the Gulf of Mexico. There are no major industries along these rivers below the phosphate operations. On the Peace River, the town of Arcadia, approximately 50 miles below the phosphate operations, obtains its water from the river. No other communities along the rivers use them as a source of water supply. Small communities, farms, and ranches are located along the rivers and both rivers drain vast swamp areas. Complaints had been received at the office of the Chief Sanitary Engineer, of the Florida State Board of Health,' that both rivers were turbid at various times and that fishing in the Alafia River was "not as good as it used to be." Tests made by another agency on the dissolved oxygen content of the Alafia River revealed that the oxygen content, at times, was comparatively low.= However, it was not shown that the phosphate wastes had any effect upon the oxygen content of the stream. The river waters are normally brown in color due to drainage from vast swamp areas and are very shallow, from 2 to 6 ft in depth. Turbid waters have been noted in streams coming from the present phosphate operations and also from streams along which there are no operations at the present time. It was learned from "old timers" that, when many more companies than at present were operating along both the Alafia and Peace Rivers forty or fifty years ago, no attention was paid to prohibiting the disposal of slimes along the river basins. During dry periods now in some of the river swamps where drainage ditches have been dug, it is indicated clearly that phosphate slimes were disposed of directly into the river swamps for many years past. Places have been observed where there were alternating strata of phosphate mud, leaf mold, and quartz sand. The former practice of indiscriminate disposal of wastes accounts for some turbidity, particularly after heavy rains and washouts and during clearing of land and digging of drainage ditches. During a six months' period in which a large tract of land was being cleared and drainage ditches dug, a small stream (Six Mile Creek), which previously had been clear, showed a turbidity of 600 ppm and remained turbid until the clearing was completed; after which the stream again flowed clear. An interview with the operator of the municipal water plant, which is about 50 miles below the phosphate operations on the Peace River and which used this river as a source of supply, revealed that there had been no taste in the water for the past ten years, other than that occasionally encountered from increased growth of algae. The operations of each of the cooperating com-

Jan 1, 1951

By Randolph C. Specht

A two year study was made of the waste disposal of the pebble rock phosphate industry. Solid slimes are impounded in large settling areas and the process water is re-used. Clear effluent was not found to be toxic to fish or animal life in field tests or in controlled experiments. Survey: The pebble rock phosphate mining and washing operations in Florida (fig. 1) are along the river basins of the Alafia to the west and the Peace to the east. The elevation of the area varies between 40 and 170 ft above sea level. Effluents from the operations find their way into one of the two river systems (fig. 2), the Peace River which flows into Charlotte Harbor and the Alafia into Tampa Bay, both along the Gulf of Mexico. There are no major industries along these rivers below the phosphate operations. On the Peace River, the town of Arcadia, approximately 50 miles below the phosphate operations, obtains its water from the river. No other communities along the rivers use them as a source of water supply. Small communities, farms, and ranches are located along the rivers and both rivers drain vast swamp areas. Complaints had been received at the office of the Chief Sanitary Engineer, of the Florida State Board of Health,' that both rivers were turbid at various times and that fishing in the Alafia River was "not as good as it used to be." Tests made by another agency on the dissolved oxygen content of the Alafia River revealed that the oxygen content, at times, was comparatively low.= However, it was not shown that the phosphate wastes had any effect upon the oxygen content of the stream. The river waters are normally brown in color due to drainage from vast swamp areas and are very shallow, from 2 to 6 ft in depth. Turbid waters have been noted in streams coming from the present phosphate operations and also from streams along which there are no operations at the present time. It was learned from "old timers" that, when many more companies than at present were operating along both the Alafia and Peace Rivers forty or fifty years ago, no attention was paid to prohibiting the disposal of slimes along the river basins. During dry periods now in some of the river swamps where drainage ditches have been dug, it is indicated clearly that phosphate slimes were disposed of directly into the river swamps for many years past. Places have been observed where there were alternating strata of phosphate mud, leaf mold, and quartz sand. The former practice of indiscriminate disposal of wastes accounts for some turbidity, particularly after heavy rains and washouts and during clearing of land and digging of drainage ditches. During a six months' period in which a large tract of land was being cleared and drainage ditches dug, a small stream (Six Mile Creek), which previously had been clear, showed a turbidity of 600 ppm and remained turbid until the clearing was completed; after which the stream again flowed clear. An interview with the operator of the municipal water plant, which is about 50 miles below the phosphate operations on the Peace River and which used this river as a source of supply, revealed that there had been no taste in the water for the past ten years, other than that occasionally encountered from increased growth of algae. The operations of each of the cooperating com-

Jan 1, 1951

By George P. Chapman

Mica is a platy mineral occurring in a variety of complex hydrous aluminosilicate forms with differing chemical composition and physical properties. Principal minerals in the mica group include: Muscovite-potassium mica (colorless or pale green/ ruby) Phlogopite-magnesium mica (dark brown or amber) Biotite-magnesium-iron mica (black or dark green) Lepidolite-lithium mica (lilac) Selected properties are given in Table 1. Muscovite is most important commercially with phlogopite of lesser use. The laminated structure of mica enables it to be split into very thin films which are transparent and tough as well as having outstanding dielectric and insulating properties. Commercially, mica is used in a number of forms (Chowdbury, 1941; Rajgarhia, 1951; Skow, 1962). Sheet mica consists of flat sheets mined from naturally occurring books of mica, free from defects and capable of being punched or stamped into required shapes. Sheet mica is separately classified into blocks, films, or splittings according to thickness. Built-up mica, or micanite, is made by arranging overlapping splittings in layers , cemented with a binder and pressed together at high temperature. Reconstituted mica, or mica paper, is made by depositing fine flakes of high-quality scrap mica in a continuous film impregnated with binder. Scrap and flake mica are normally unsuitable in quality or size for making sheet mica. Originally the term scrap mica referred to the waste byproduct of mining and fabricating sheet mica, and distinct uses were developed for this material. Subsequently it became economically feasible to mine lower quality mica for these uses, and the term flake mica was introduced. Although the two terms are still used somewhat synonymously, it is considered better, at least in the United States, to use the term flake mica in referring to mica mined for uses other than as sheet mica; and to restrict the term scrap mica to mica mined for or with sheet mica, but which will not meet the specifications. Synthetic mica, such as fluorophlogopite, is produced by slow crystallization of a melted blend of pure raw materials. Mineralogy In the true sense the term mica does not relate to, a particular mineral, but to a group or family of minerals of similar chemical composition and to some extent similar physical properties. These minerals are predominantly potassium aluminum silicates with varying amounts of magnesium, iron, and lithium. The precise formulas and isomorphic relationships of the various group members have been studied, but general agreement has not been reached (Grimshaw, 1971; Hurlbut, 1952; Skow, 1962). The general formula describing the chemical composition of micas is [X2Y4-6Z8020(OH, F)4, where X is mainly K, Na, or Ca; Y is mainly Al, Mg, or Fe; Z is mainly Si or Al (Deer, et al., 1962).] These minerals have an internal structure of the layered lattice type where the silicon atoms are in the center of a tetrahedral grouping of oxygen atoms. The groups are linked together in a single plane by three oxygen atoms that lie within the common plane. Each of these oxygen atoms is shared by two tetrahedra. These linked tetrahedral groups, when continually extended, produce a hexagonal network within the plane. This internal structure of the mica has been used to explain the ex-

Jan 1, 1983

By Ihor A. Kunasz

Lithium minerals occur predominantly in pegmatites which contain mineral assemblages derived from the crystallization of postmagmatic fluids or from the metasomatic action by residual pegmatitic fluids. They have been the traditional sources of raw materials for ceramic and chemical industries. However, with the discovery of Searles Lake, brines became new sources of lithium. Indeed, the 1960s may well be referred to as the "brine decade" because several brine bodies of significant economic importance were discovered. In the United States, the brines of Clayton Valley, Nevada, presently exploited by Foote Mineral Co., and the Great Salt Lake of Utah, to be exploited by the Great Salt Lake Chemicals Corp., have been defined as major sources of lithium. Also a lithium-bearing brine has been discovered in Chile. Following the termination of the AEC purchase program in 1959, several companies such as Maywood Chemical Co., American Lithium Chemicals, and Quebec Lithium Corp. were forced to close down their operations. Nevertheless, with the development of new applications in glass ceramics, air conditioning systems, synthetic rubber, and metallurgy (aluminum potlines), the lithium industry grew steadily, and with the potential application of lithium metal in batteries and nuclear reactors, a healthy growth can be foreseen. New products and new applications are likely to stimulate exploration for expanded reserves as well as the search for new sources from which lithium could be extracted economically. Geochemistry of Lithium Lithium is the third element in the periodic table. It is the lightest of all the metals, having an atomic weight of 6.938. Its ionic radius is 0.60A and its charge is + 1. The geochemistry of lithium has been extensively studied and has been summarized by Rankama and Sahama (1950), Goldschmidt (1937), and Hortsman (1957). The distribution of lithium in igneous rocks is controlled by its size and its charge, and by the (MgO+FeO)/Li2O ratio. In the early stages of crystallization of a magma, that ratio is very large. Consequently, both magnesium and iron are removed by ferromagnesian minerals in preference to lithium which is then concentrated in the residual magma. This results in an enrichment of lithium in silicic rocks and pegmatites (Strock, 1936). Pegmatites are coarse-grained igneous rocks formed by the crystallization of postmagmatic fluids. Minerals within pegmatites may also form by metasomatism (Jahns. 1955). Genetically, the pegmatites are associated kith neigh- boring intrusives. Mineralogically, granitic pegmatites contain feldspar, quartz, and mica as the main constituents and a variety of exotic elements such as lithium, beryllium, tantalum, tin, and cesium, which may or may not occur in economically significant concentrations. Detailed studies by numerous investigators (Cameron et al., 1949, 1954; Hanley et al., 1950; Jahns, 1953, 1955; Page et al., 1953) indicate that pegmatites often exhibit an internal zonal arrangement, with each zone containing a specific suite of minerals. The lithium minerals are usually found in the intermediate zones, and although as many as 13 zones have been recognized by Cameron, a complete zonal arrangement is rarely found. Zoning of pegmatite bodies has also been observed on a regional basis. The regionally zoned pegmatite sequences exhibit mineral assemblages and complexity according to their respective distance from the granitic bodies to which they are genetically related (Mulligan, 1965). Lithium is also found in small proportions in a variety of rocks. The average lithium

Jan 1, 1975

By S. J. Rothman, J. J. Hines, D. Rokop, R. Bastar

Self-diffusion has been measured along each principal axis of mosaic-structured and relatively perfect a uvaniuln single crystals. The anisotropy reported before,' D[loo] = D[001] » D[010 , has been confirmed. and is shown to represent volume diffusion. Diffusion along the dislocations in the imperfect crystals increases the measured value of D significantly without changingr either the shapes of the penetvation plots or the anisotropy. SINCE a uranium is orthorhombic, the diffusion coefficients along the principal crystallographic axes need not be equal. A previous measurement of self-diffusion in three mosaic-structured a uranium single crystals1 showed that Dil00| =D[001 >>D[010 This result was deduced from penetration plots similar to those in Fig. 1. That is, the plots for diffusion along [loo] and [001] were the straight lines expected from the solution of the diffusion equation for the boundary and initial conditions of the experiment, while the plot for diffusion along [010] was curved so that the part near X = 0 had a much steeper slope than the straight lines did. The observed anisotropy could have been due either to volume diffusion or to diffusion along the very large number of dislocations in such crystals, according to the model proposed by aart.' The authors of Ref. 1 argued that the latter possibility was unlikely, but did not exclude it. To settle the question, a simultaneous measurement of self-diffusion in mosaic-structured and mosaic-free crystals was carried out. This paper reports the results, as well as a measurement of the temperature dependence of self-diffusion in a uranium. EXPERIMENTAL The single crystals of a uranium used in this experiment are listed in Table I, together with other experimental details. '(Mosaic structured" here means crystals grown by solid-state phase change.3 The Laue spots from such crystals spread over about 6 deg of arc, which indicates that the density of dislocations is very large. "Perfect" crystals are ones grown by Fisher's grain-coarsening tehnique; the Laue spots from these are quite sharp,4 which shows that the dislocation density in these crystals is much lower. All of the crystals were made from high-purity uranium; a typical analysis is given in Ref. 1. The actual diffusion directions were within a few degrees of the nominal. The thin layer-sectioning method was used. The experimental techniques were similar to those described in Ref. 1, except the sectioning. Crystals Za, 2b, 2c, 4a, 4b, and 4c were sectioned on a lathe. Crystals 3a, 3b, and 3c were sectioned by grinding on glass plates, with 1 p diamond powder in butyl alcohol as the abrasive. The use of glass plates eliminated the crowning noted in Ref. 1, and the use of butyl alcohol as a lubricant simplified the chemical processing of the sections. Material from the sides of these three crystals was removed by spark machining before sectioning. The sectioning of crystals 4a and 4c was botched. A small cylinder of metal was extruded from the center of crystal 4a while turning off material from the side of the sample. Crystal 4c was misaligned by 2.1 x 10"3 cm because the dial gage jammed during the alignment. Notwithstanding these errors, useful data were still obtained from these crystals. The points

Jan 1, 1967

By P. A. Beck, Hsun Hu

As described by means of quantitative pole figures, the annealing texture of highly rolled aluminum consists of the four retained components of the rolling texture near (123) [121], rather more sharply developed, and of a cube texture component. Local reorientation corresponds fairly well to 40 rotation around a [111] axis. In copper strip rolled 96 pct, the annealing texture is mainly the cube texture, with the four twin orientations as minor components. The annealing texture of highly rolled brass strip consists of four components of the (225) [734] type. REVIEWS by Wassermann,' Barrett,' Dunn,3 and Richards' give detailed accounts of the numerous publications dealing with annealing textures in rolled polycrystalline metals. Although a considerable amount of information of an empirical nature has been available for many years, even relatively recently the state of recrystallization-texture theory was considered uncertain. The reviews referred to above deal mainly with the description of experimental results, without developing generally applicable principles, suitable for explaining the observed annealing textures. The investigations of Burgers and Louwerse5 and Barrett6 showed that in deformed single crystals of aluminum the orientation of the recrystallized grains deviates drastically from that of the deformed matrix. According to Barrett and to Beck and Hu,7 the relationship between the two orientations can be best described as a rotation of about 40° around a [111] axis. Recent investigations led to similar orientation relationships for various face-centered cubic metals with a simple texture, regardless of whether the annealing process was recrystallization (strain-free grains growing in a highly deformed large crystal of aluminum' or copper: or in deformed cube texture copper") or coarsening (strain-free grains growing at the expense of an essentially strain-free, fine grained, polycrystalline matrix of single orientation texture copper,'" aluminum,' or nickel-iron). Barrett" pointed out the possibility that this orientation relationship may be a result of the orientation dependence of the rate of grain boundary migration. More recently, considerable evidence became available in favor of this view.12,13 In apparent contradiction to the above results, it has been known for a long time that the recrystallization texture of polycrystalline metals is often similar to the deformation texture. This was found, in particular, for the fiber textures obtained by wire drawing, compression, or compression rolling.' Following a suggestion by Barrett,2 Kronberg and Wilson and Beck and Hu7 described a mechanism by which a [Ill] fiber texture, resulting from plastic deformation, may be retained upon recrystallization, even though the orientation of individual recrystallized grains differs from that of the local area of the matrix in which they grow. This mechanism assumes that the reorientation corresponds to a rotation around the [1ll] axis, which is also the fiber axis. The present investigation was undertaken to examine in detail the orientation relationship between deformation texture and recrystallization texture in rolled face-centered cubic metals, using the quantitative methods of texture determination that have recently become available.", '" Quantitative pole figures for the rolling textures of such metals were reported recently." Quantitative pole figures for annealing textures are given in the present paper. It was planned to investigate whether or not the orientation relationship previously found for the recrystallization of deformed single crystals, and for coarsening of single-orientation texture material, is capable of accounting for the observed, often complex, annealing textures in rolled polycrystalline metals. The question whether local reorientation is predominant, even in the early phases of the annealing process, was to be studied with high purity aluminum. by making use of an oxide film and sensitive tint illum-

Jan 1, 1953

By W. G. Oldham

By monitoring the capacitance of abrupt p-n junctions it is possible to follow the motion of substitu-tional impurities. A p-n junction is formed by growth of silicon from an Al-Si alloy on an n-type silicon sutstrate at a temperature in the range 650" to 750°C. The diodes are etched and sorted for consistent V-I and capacitance behavior and separated into groups. After irradiation, each set with an unirradiated control set is annealed to various temperatltres for 10 mm and the capacitance remeasnred. For very heavily doped diodes (-1019 per cm3) observable capacitance changes occur at neutron fluences of >1015 per cm 3. The results may be interpreted in seceral ways, the simplest of which is to assume simple vacancy diffiision with small impurity -racancy interaction (at the diffiision, i.e. annealing temperature of 700°C). In this interpretation it is found that a typical vacancy makes about 1024 jumps and travels about 10-5 cm before disappearing. The required effective annihilation center density is about 1016per cm3 . Estimates of the vacancy-impurity interaction can be made and the above numbers correctecl, but for arty reasonable assumptions the number of vacancy sinks connot be much reduced. ThE complete annealing of radiation induced defects requires that the vacancies and interstitials either recombine, travel to the surface of the crystal, or travel to an annihilation center, e.g., a dislocation or a precipitate. If the interstitial is ignored except as a possible vacancy annihilation center at low temperatures,* the motion of vacancies may be followed by monitoring the corresponding motion of substitutional impurities. pfister2 has measured the enhanced diffusion of impurities in an asymmetric shallow diffused silicon structure by optically monitoring the junction movement. In these experiments we monitor instead the capacitance of a heavily-doped deep symmetric p-n junction. The sensitivity for this method is several orders of magnitude higher than in Pfister's technique, mainly for two reasons: 1) the junction capacitance of a heavily-doped junction is sensitive to impurity movements in the Angstrom range* com- and 2) the junction may be far from the surface which is a major annihilation center for vacancies. THE EXPERIMENT A p-n junction is formed by the epitaxial growth of silicon from an A1-Si alloy on a silicon substrate at a temperature in the range 650° to 750°C. The technique used is the transport of an aluminum melt through a temperature gradient.4 A 10-mil thick aluminum disc is sandwiched between two silicon wafers and the assembly raised to about 650° C with a temperature gradient normal to the sandwich. After about 8 hr the upper (hotter) wafer has been entirely transported and deposited epitaxially on the substrate wafer. The substrate and overgrowth resistivity are measured with a 4-point probe. The as-grown structure is lapped until the wafer is about 1/2 mm thick with the junction in the center. Contacts consisting of electroless nickel covered by electroplated rhodium are applied to both the p and n sides. The wafer is diced into square dice 1/2 to 1 mm on a side and the dice are etched sufficiently to remove approximately 1 mil of silicon. The following results are all for aluminum (p-side) and antimony (n-side) doped specimens with NA =3x 1018 per cm3, ND = 2-8 x 101A per cm3. The diodes are sorted for consistent V-I and capacitance behavior and separated into groups. After irradiation, each set with an unirradiated control set is annealed and the capacitance remeasured. A special capacitance measurement method is used to insure a low sensitivity to shunt resistance. The diode is voltage driven and the current monitored by a phase lock amplifier. It is possible to adjust the detector phase to a point where shunt resistances as low as 100 O have no effect on the reading. The diodes in this study have a capacitance in the range 1000 to 5000 picofarads and a shunt resistance in the range 100 to l06 O depending on the stage of the anneal. THEORY The theoretical problem is twofold: 1) The computation of the amount of impurity diffusion and hence the impurity profile resulting from a given amount of vacancy motion, and 2) the computation of the capacitance from the impurity profile. A comparison of the theoretical and experimental capacitance (in particular the changes) yields the amount of vacancy motion. Vacancy Motion. A convenient parameter to measure the total amount of vacancy motion is Jv the total number of vacancy jumps per unit volume. Although this parameter varies with position in the crystal, owing to vacancy annihilation at the surfaces, it is approximately independent of position far from the surfaces, i.e. in the junction region. In terms of the number of vacancies per unit volume Nv and the vacancy diffusivity given by

Jan 1, 1970

By W. B. Gogarty, H. R. Bailey

Methods are presented for determining molecular diffusion coefficients by using data from, capillary flow experiments. These methods are based on a numerical solution (presented in a previous paper) of the partial differential equation describing the combined mechanisms of flow and diffusion. Results from this numerical solution are given and compared with the approximate analytical solution of G. I. Taylor. The numerical solution is valid over a much larger time range. These methods are applied to experimental results for the fluid pairs water-potassium permanganate solution and amyl acetate-orthoxylene. Both of these fluid pairs have approximately equal densities and viscosities. Graphical and numerical techniques are presented for deter mining diffusion coefficients from the flow data. Values obtained by these techniques are compared with values obtained by other methods. INTRODUCTION The molecular diffusion coefficient is known to be a variable in determining the amount of mixing in a miscible displacement process. The effect of molecular diffusion on dispersion in longitudinal flow through porous media -has been examined by different investigators. These investigators concluded that at low velocities of flow, the amount of dispersion is approximate1y proportional to the molecular diffusion coefficient. The influence of diffusion on fingering, channeling, and overriding has been mentioned by other investigators.4 Recent studies5,6 have been made on the effects of molecular diffusion in connection with the problem of gravity segregation. Many different methods have been developed for the experimental determination of molecular diffusion coefficients? These methods differ mainly according to boundary conditions selected and analytical procedures used. Nevertheless, all of these methods have the condition in common that the bulk fluids in which diffusion is occurring are stationary with respect to each other. In connection with a series of papers on mixing in capillary flow,8-10 Taylor suggested the use of a flow method for determining molecular diffusion coefficients. Additional studies 11-13 have been conducted on miscible displacements in capillary tubes, but the data from these studies were not used for the specific purpose of determining diffusion coefficients. The flow method proposed by Taylor results in a single value of the diffusion coefficient for the fluid pair used in the displacement experiments. This single value represents the true value for the fluid pair when the diffusion coefficient is independent of concentration. If the diffusion coefficient is a function of concentration, the single value obtained by the flow method gives an average value for the coefficient of the fluid pair. These average values are based on diffusion taking place over the entire range of concentration, i.e., from 0 per cent of one fluid to 100 per cent of that same fluid. In field applications of the miscible displacement process, gradients occur over the same range of concentration as are found in the displacements in capillary tubes. Molecular diffusion coefficients obtained from the capillary flow method should, therefore, be especially relevant to field operations. This investigation was undertaken to evaluate the feasibility of obtaining molecular diffusion coefficients from capillary -flow experiments. In making this evaluation, diffusion coefficients were first determined for two systems from data obtained in capillary flow experiments. These values of the diffusion coefficient were then compared to values obtained by other methods. MIXING IN CAPILLARY FLOW—THEORETICAL The theoretical basis for determining molecular diffusion coefficients from capillary flow experiments is the partial differential equation relating the mechanisms of flow and diffusion. For the case of laminar flow and with a fluid pair having equal densities and viscosities, the equation is given by

By W. B. Gogarty, H. R. Bailey

Methods are presented for determining molecular diffusion coefficients by using data from, capillary flow experiments. These methods are based on a numerical solution (presented in a previous paper) of the partial differential equation describing the combined mechanisms of flow and diffusion. Results from this numerical solution are given and compared with the approximate analytical solution of G. I. Taylor. The numerical solution is valid over a much larger time range. These methods are applied to experimental results for the fluid pairs water-potassium permanganate solution and amyl acetate-orthoxylene. Both of these fluid pairs have approximately equal densities and viscosities. Graphical and numerical techniques are presented for deter mining diffusion coefficients from the flow data. Values obtained by these techniques are compared with values obtained by other methods. INTRODUCTION The molecular diffusion coefficient is known to be a variable in determining the amount of mixing in a miscible displacement process. The effect of molecular diffusion on dispersion in longitudinal flow through porous media -has been examined by different investigators. These investigators concluded that at low velocities of flow, the amount of dispersion is approximate1y proportional to the molecular diffusion coefficient. The influence of diffusion on fingering, channeling, and overriding has been mentioned by other investigators.4 Recent studies5,6 have been made on the effects of molecular diffusion in connection with the problem of gravity segregation. Many different methods have been developed for the experimental determination of molecular diffusion coefficients? These methods differ mainly according to boundary conditions selected and analytical procedures used. Nevertheless, all of these methods have the condition in common that the bulk fluids in which diffusion is occurring are stationary with respect to each other. In connection with a series of papers on mixing in capillary flow,8-10 Taylor suggested the use of a flow method for determining molecular diffusion coefficients. Additional studies 11-13 have been conducted on miscible displacements in capillary tubes, but the data from these studies were not used for the specific purpose of determining diffusion coefficients. The flow method proposed by Taylor results in a single value of the diffusion coefficient for the fluid pair used in the displacement experiments. This single value represents the true value for the fluid pair when the diffusion coefficient is independent of concentration. If the diffusion coefficient is a function of concentration, the single value obtained by the flow method gives an average value for the coefficient of the fluid pair. These average values are based on diffusion taking place over the entire range of concentration, i.e., from 0 per cent of one fluid to 100 per cent of that same fluid. In field applications of the miscible displacement process, gradients occur over the same range of concentration as are found in the displacements in capillary tubes. Molecular diffusion coefficients obtained from the capillary flow method should, therefore, be especially relevant to field operations. This investigation was undertaken to evaluate the feasibility of obtaining molecular diffusion coefficients from capillary -flow experiments. In making this evaluation, diffusion coefficients were first determined for two systems from data obtained in capillary flow experiments. These values of the diffusion coefficient were then compared to values obtained by other methods. MIXING IN CAPILLARY FLOW—THEORETICAL The theoretical basis for determining molecular diffusion coefficients from capillary flow experiments is the partial differential equation relating the mechanisms of flow and diffusion. For the case of laminar flow and with a fluid pair having equal densities and viscosities, the equation is given by

By David W. Wisecarver, James F. Reynolds

INTRODUCTION The Department of Energy is cooperating with Snowmass Coal Company near Carbondale, Colorado to introduce the longwall mining method in moderate to steeply pitching coal seams in the United States. This venture is part of a coal mining research program directed toward development, trial, and analysis of mining technique8 to improve production and recovery in the more difficult mining conditions such as thick, multiple, and steeply pitchly seams found in the Western U.S. The project at Snowmass is the first attempt in the United States to operate a longwall in a steep coal seam. Plans are to mine three adjacent, successively downslope panels in the eight foot thick seam which varies in pitch from 27 to 33 degrees. During this work, researchers and mine engineers are expected to obtain answers to many engineering questions relative to panel design and development, selection of face equipment and beet operating techniques and procedures. They are also committed to obtaining hard data on costs, recovery, production, safety, and behavior of underground mine structure as the three panels are mined. This information is essential to future mine engineering and profitable mining of pitching Western coal reserves. Development of the first trial panel was begun in 1979 and completed in June 1981. The longwall mining equipment was then installed in the starting room and retreat mining begun on August 11, 1981. Project duration is expected to be about five years during which over tm million tons of coal will be produced. TRAINING The longwall mining method is new to Snowmass. For years the mine produced coal by room and pillar methods using conventional techniques to mine upslope rooms and Alpine F6A miners to cut entries and rooms on strike. Miners were experienced in room and - pillar mining from other mines. News of the longwall demonstration was received enthusiastically by Snowmass miners. Employee interest in the project was 100%. However, there was minimal longwall experience on site. In fact, most of the work force had not even seen a longwall. Mine and company management were well aware of the immediate need to develop trained longwall face mining crews and maintenance people qualified to work on longwall equipment and also expertise in longwall planning, equipment selection, power distribution design, ventilation requirements and panel development. The first approach to answer this huge deficiency in longwall mining experience was obviously training. Hence a training program directed toward those mining specifics most urgent to the beginning mining phases was initiated in mid-1980. Classroom lectures and hands on training, using instructors from equipment suppliers and available company longwall expertise, was conducted in longwall subjects to include face mining procedures, panel development, operation of equipment, equipment assembly and maintenance, electrical circuitry and controls, ventilation, move of longwall equipment, and safety procedures. At the same time, responsible engineers and foremen were sent on a tour of European pitching longwalls to see first hand how other mines working under similar seam conditions conducted their operations. Development techniques, types of equipment, methods for transport of men and materials, and ground control techniques were discussed with engineers, foremen and officials at each mine. This look at European longwall mining operations gave Snowmass good insight into the unique problems associated with longwall mining on 30' pitch. Mining considerations such as face conveyor/ support system slippage downslope, panel development, maintenance, safety considerations, manpower requirements, and haulage methods were covered with European experts

Jan 1, 1982