Search Documents

By Edwin T. Myskowski, Alfred H. Hesse

The development by the U. S. Bureau of Mines of a process for purifying manganese by electrolysis has stimulated interest in manganese alloys. While recent publications have shown some alloys of manganese and copper to possess rather unusual properties, none have included information on tensile properties, which have an important bearing on the usefulness of the alloys. Manganese-copper alloys can be heat-treated, since the single phases that exist at high temperatures may be retained by quenching. According to Persson,1 when quenched alloys containing from about 30 to nearly IOO per cent manganese are reheated, alpha manganese is precipitated (Fig. I). Calculations based on Persson's X-ray data indicate that this decomposi-tion is accompanied by a change in volume of as much as ; per cent. The reason that this large volume change has not been noted probably is the slow rate at which equilibrium is reached by these alloys. In an investigation on hardening by cold-work and heat-treatment, Dean and Anderson3 found that quenched alloys increase in hardness with manganese content and that high-manganese alloys harden very slowly with cold-work, while high-copper alloys harden much more rapidly. Heat-treatment has little effect on manganese-copper alloys containing less than 40 per cent Mn, and affects those alloys containing more than 40 per cent in accordance with their manganese content and heat-treating temperature. Dean and Anderson4 also found that cold-work increased electrical resistance of alloys containing from 50 to 80 per cent Mn, and that heat-treatment of alloys containing from 40 to 96 per cent Mn altered the electrical resistance considerably. Dean, Anderson and Potter6 have shown that the high vibration damping capacity that characterizes manganese-copper alloys containing 40 to go per cent Mn is affected by cold-work and heat-treatments. Highest vibration damping capacity at low stresses was obtained by heating for 2 hr. at 450°C. (842°F.) after quenching from solution temperatures. Preparalion of Alloys.—The alloys for these tests were melted in a 17-lb. basic-lined high-frequency induction furnace using electrolytic manganese, grade A ingot copper and a 70-30 CU-Mn master alloy (69.80 per cent Cu, 0.12 Fe, 0.04 Si, 0.006 S, 0.07 C, balance Mn). The manganese was heated slowly to expel excess dissolved gases and melted before the addition of copper. No fluxes or covers were used. The melts were cast in tapered iron molds and the ingots were reduced go per cent when forged to 1/2-in. rounds. These rods were given 2-hr. solution treatments at temperatures that depended upon the composition (Table I). Tensile Tests.—The tensile specimens, 0.313-in. diameter (1.25-in. gauge length),

Jan 1, 1942

By C. Richard Tinsley

INTRODUCTION Project financing has been defined by various authors in this book. It is founded on reliance upon the project's own future cash flows and secondarily on the collateral value of the asset base developed. It is chiefly provided by the banking community who, after an assessment of the risks involved (See Chapter 9) analyse the company's presentation (See Chapter 10) in order to structure a financing package often at a leverage of up to 80% debt. This paper describes the various support and structuring techniques used to delimit and abate the risk components perceived from the banks' experience on project development especially for the period before cash flow is generated (pre completion). ADVANTAGES The advantages of project financing extend beyond the offloading of risks to banks. Among the advantages are the following: 1. Longer loan maturity than conventional, unsecured financing; 2. Loan disbursement and repayment tailored to specific mine; 3. Ability of a joint venture without a "track record" to raise financing; 4. Obtain financing where further direct borrowing (corporate credit) limited by existing indentures; 5. Possibility of arranging finance off-balance sheets; 6. Leverage return on equity; 7. Obtain tax savings with certain project financing structures; and 8. Obtain flexible loan repayment conditions. It can also be said that from the point of view of the company, project financing has certain disadvantages which can be summarised as follows: 1. Perceived higher cost (risk premium) compared with straight corporate credit; 2. More documentation; and 3. Need to negotiate risk-sharing aspects. The main attraction of project financing is the ability to pass certain risks on to the lenders within a flexibly funded transaction. (For a more detailed description of the specific risks see the author's paper at the beginning of Chapter 9. The same risk system is followed here.) The typical project financing has corporate support prior to completion and will usually carefully control the resultant cashflow after completion to ensure the bank does not unnecessarily assume further risks of an equity nature. WITHIN THE COMPANY'S CONTROL Operating Risk This is broken into three interrelated segments for ease of description. Technical Component: This must be specifically addressed if new technology or unproven adaptations are to be used. The banks will have scrutinized the sampling and bulk testing work, perhaps grilling the geological, mineral processing, metallurgical, and mining engineering staff or consultants directly. A number of supports are available such as: TECHNOLOGY GUARANTEE: Either the company itself or the process developer will guarantee that the technology will work for a period of, say, six months to two years after startup. If not, then financial penalties will apply although these are rarely sufficient to repay the loan. Many process developers are weak financially and may have little substance to back such a guarantee.

Jan 1, 1985

By R. I. Jaffee, H. R. Ogden, D. J. Maykuth

Phase diagrams for the Ti-W and Ti-Ta systems were determined. The Ti-W system is characterized by a wide, two-phase region of ß plus tungsten which is derived from a peritectic reaction between the liquid and tungsten solid solutions. The ß field terminates in a eutectoid reaction between a titanium and tungsten terminal solid solution. Tantalum and ß titanium form a complete series of solid solutions. Other features of this system are the extensive a-ß field at low temperatures and an appreciable solubility of tantalum in a titanium. BOTH tungsten and tantalum were first thought to form ß-isomorphous systems with titanium as a result of early work' using powder-metallurgical techniques. Later work2 on arc-melted Ti-Ta alloys, made using a commercial titanium base, showed that, in the range of 0 to 10 pct, tantalum was soluble in ß titanium and that the a solubility extended to between 2 and 5 pct Ta at 790 °C. The present investigation covered the entire alloy range in both systems and was chiefly concerned with high-purity alloys at the titanium-rich end. The constitution of titanium-rich alloys made with a commercial titanium base was reported by Holla-day, Kura, and Jackson.3, 4 As will be shown in detail later, the early prediction of a isomorphism was true for the case of the Ti-Ta system, but not for the Ti-W system. The results of this investigation will be presented first. The experimental methods used are described in the Appendix. Ti-W System The entire Ti-W phase diagram is shown in Fig. 1. Details of the titanium-rich side are shown in Fig. 2. The chief features of the system are a ß eutectoid and a high-temperature peritectic between liquid and tungsten solid solution. Melting Range: Examination of cast structures of low and medium-tungsten-content ingots showed cored ß phase as the primary constituent. Fig. 3a illustrates a typical cast structure for alloys in the range of 20 to 30 pct W. From 30 to 72 pct W, coring was very severe. Alloys containing 72 through 88 pct W, however, showed definite evidence of a peritectic reaction between the liquid and a terminal solid solution of titanium in tungsten. Fig. 3b shows the cast structure for an 80 pct W alloy. A 95 pct W alloy, shown in Fig. 4, consisted primarily of primary tungsten solid solution plus a small quantity of ß probably rejected during cooling. Incipient-melting experiments located the peritectic temperature between 1850" and 1900°C and indicated that the reacting phases are liquid containing about 25 pct W and tungsten terminal solid solution containing about 8 pct Ti. Figs. 5 and 6

Jan 1, 1954

By P. Campbell, E. M. Gardy, L. Hachkowski

Introduction The efficient process control of a uranium mill and its associated mining operation requires a nearly continuous knowledge of the uranium concentration in the ore. Generally, the approach is to use laboratory assays of grab samples from the mill feed belt. In some cases, elaborate and expensive systems have been used to ensure random sampling, but even with these systems, mass-balance discrepancies still exist. There is a requirement for an on-line instrument that can give a prompt, accurate analysis of a large portion of the feed stock. The authors have recently evaluated a laboratory system that achieves these goals using neutron activation and delayed neutron counting. The development of the on-line uranium ore analyzer is a consequence of previous work done at the Whiteshell Nuclear Research Establishment (WNRE) (Campbell et al., 1978 and 1981), and is based on the emission of delayed neutrons after the neutron irradiation of fissionable materials. The mechanism of delayed neutron emission has been described (Keepin, 1965), but briefly is as follows. The fission fragments resulting from irradiation are in an excited state. Certain of these delayed fission products, precursors, decay to a more stable state by the emission of a delayed neutron. The delayed neutrons can be divided into six groups with effective half-lives ranging from 0.2-55 sec. It is important to note that more than 50% of the delayed neutrons are emitted within the first 6 sec after irradiation; this has an influence on the design of the analysis instrument. Measurement Cycle The measurement cycle involves a neutron irradiation, a delay time, and a counting period. The laboratory demonstration model of the ore analyzer comprises a californium-252 neutron source, a source chamber, a pneumatic transfer facility, and a neutron irradiation and counting module [(Fig. 1)]. The ore sample is placed in the irradiation chamber. The neutron source is transferred to the center of the chamber for a 5-sec irradiation while the helium-3 thermal neutron detectors are switched off. As the source returns to the storage chamber, the detectors are switched on and the delayed neutrons counted. The total assay cycle is 16 sec. The current instrument design calls for the ore to be cut from the main belt every 16 sec by a mechanical arm and dropped into the analyzer directly, or via another belt. The cycle starts when there is a sufficient mass of ore in the irradiation chamber to depress a switch and stops when the delayed neutron count is finished. The ore is then dropped through the bottom of the analyzer chamber and returned to the main belt. The counts from each cycle are accumulated and the data reduced to give the desired information.

Jan 1, 1985

By W. H. Gunniss

When the copper smelters were built, in Montana, all of the refractory products which were used in their construction were shipped in from Eastern factories. It was apparent that if a material suitable for the manufacture of these products could be found within the State, a saving of freight could be effected and a new industry built up. Prospecting for such materials was started and experiments were made with samples from numerous deposits. Considerable effort and funds were expended in an attempt to manufacture silica brick from Dillon quartz, a light colored sandstone that is found near Dillon, Mont., on the Oregon Shortline railroad. As a brick material the Dillon quartz was a failure, but it has proved very satisfactory as a silica cement. It is now being used in laying silica brick and for reverberatory furnace bottoms. A bed of quartzite that is particularly suited to the manufacture of high-grade silica brick was finally discovered at Browns Spur, 6 miles west of Anaconda. The material from this deposit is now being used in the manufacture of the Anaconda silica brick, which have gained a wide reputation for heat-resisting and lasting qualities. The analysis of an average sample of this quartz is: SiO2, 96.7; Fe2O3, 0.3; Al208, 2.5; CaO, 0.3 per cent. The very low percentage of fluxing ingredients makes this a most refractory material. All of the Anaconda silica brick are hand molded. Various types of brick machines have been tried, but the hand-mold process proved the best suited to the manufacture of silica brick from this material. The silica is first put through a jaw crusher and is then dumped into wet pans, where 4 per cent. of lime paste is added, to produce a bond. Without the lime the material would not be plastic enough to mold. After a few minutes' grinding in the wet pans the material is conveyed to the molder, who forces it into the molds by hand. The brick are then dumped on pallets and placed in the drier, where they are left. until dry enough to be set in the kilns. Some of the brick are re-pressed before being dried. They are burned about five days, in round down-draft kilns. It is not necessary to have as much heat in the kilns as the brick will be subjected to when in use in the furnaces. Montana refractories are used in smelters throughout the West. Prospecting for fire clays was also carried on. After experimenting with clays from several different deposits, it was found that a mixture of

Jan 1, 1914

By J. L. Lummus, Frank O. Jones

A field procedure for determining graphite in drilling mud is presented which is sensitive to 0.25 lbs/bbl and accurate to 20 per cent. The method, utilizing oil flotation principles, is suitable for use in all oil-free water base muds except those containing ligno-sulfonates, lignites, or surface active agents. INTRODUCTION Graphite was proposed as a drilling lubricant as early as 1940, but has not been used extensively until recently.' Graphite has been substituted for oil in certain instances to avoid oil contamination of core samples since it has been found that graphite does not interfere with routine core analysis. A major difficulty in using graphite is the lack of a satisfactory field test for determining the concentration of graphite in mud. DISCUSSION OF METHOD Several possible methods of analysis were investigated, including chemical separation, density fractionation, radioactive tracers, and oil flotation.', ' The investigation indicated that a satisfactory method for field use could be devised using an oil flotation method. It was found that toluene shaken with a highly diluted mud sample would recover sufficient graphite to be apparent in the oil phase. Refinement and standardization of technique made it possible to detect as little as 0.25 lb/bbl graphite and to estimate graphite content to within 20 per cent by using a visual comparison method. The test is limited to oil-free water base muds. Quebracho, phosphates, or barytes in the mud do not interfere with the test but surface active agents, lignosulfonates' and lignites evidently render !he graphite water-wet so that none may be recovered by oil-flotation. PROCEDURE Instructions for determining graphite in mud: 1. Collect representative one gallon sample.- from mud stream. Transfer immediately 350 ml portions of this Sample into four mixing cans labeled A, B, C, and D. Measure out graphite (same as is used to treat mud) for addition to cans as indicated below, using either a specially designed scoop or a balance. Can: A B C D Grams Graphite to Add: none 2 4 6 Stir samples B, C, and D for 15 minutes with propeller type mixer. 2. Clean and rinse well with water four 250 ml volumetric flasks labeled I, 11, 111, and IV. Using a 5 ml hypodermic syringe, transfer the indicated volume of samples from cans A, B, C, and D into designated flasks as follows: From Can: A B C D To Flask: I II III IV Add This Volume of Mud: 4 ml 2 ml 2 ml 2 ml 3. Measure 100 ml fresh or distilled water to each flask and swirl gently to disperse mud. Add exactly 5 ml toluene to each flask. Stopper and shake each

Jan 1, 1953

By H. B. Hunter, F. G. Stone, F. J. Dunkerley

Introduction and Literature Survey This is the second in a series of papers coming from this laboratory on the correlation of the low temperature tensile properties of tin-binary alloys with microstructure. These engineering data and those of the previous paper1 were obtained as the initial part of a long-range program to determine the changes in the fundamental mechanical properties accompanying the beta to alpha phase change in tin and its binary alloys below 13.2°C. Since it appears now that the more fundamental studies will be delayed,* and since no summary of the low temperature properties of these tin-base white bearing alloys was found in the literature, it was decided to publish all the engineering data thus far obtained. Accordingly, the tensile properties of thirteen binary alloys containing from 0.1 to 60 pet cadmium and 0.1 to 10.43 pet antimony measured at six temperatures from —196 to +23°C are presented here and their variations rationalized in terms of microstructure. A literature search showed that these systems had not been investigated at low temperatures, although both the tin-cadmium and tin-antimony2,3,4,5 and the tin-rich corner of the ternary system67 have been studied at room temperature. Hanson and Pell-Wal-pole5 and Homer and Plummer4 determined the tensile properties of alloys containing from 0 to 10 pet cadmium. The same authors3 determined the tensile strength and elongation in the tin-antimony system from 2 to 18 pet antimony at room temperature while Pell-Walpole et al.6,7 studied the properties of high tin and tin-antimony-cadmium alloys. Since there were many variables besides composition in these tests, it was difficult to make a valid comparison with the room temperature data of the present study, but in general the tensile strength and ductility values are in reasonable agreement. Pell-Walpole2 also determined the effect of grain size on the tensile strength of pure tin and 1 pet alloys of both antimony and cadmium. The true maximum stress was found to decrease exponentially as the number of grains in the cross-section increased. This effect of grain size was strikingly revealed in the present work, as indicated in a later section. Hanson and Pell-Walpole8 placed the solid solubility limit of antimony in tin at 3.5 pet at 20°C, increasing to 4 pet at 190°C, and then sharply increasing to 10.3 pet at 246°C (the latter being a peritectic point). Their results are in disagreement with those of previous investigators,9 and the discrepancy seems to lie in the micro-graphic observation of the second phase

Jan 1, 1950

By L. D. Jaffe, H. C. Mann, E. L. Reed

The authors have recently published1 evidence that brittle transgranular fracture of polycrystalline metals does not originate at a point and propagate continuously across the material, but rather develops at numerous related points, leading to a series of micro-cracks which subsequently link up. Series of related microcracks were observed in steel specimens broken in fatigue—specifically, at the central portions which broke during the final sudden fracture. Microcracks of the type mentioned have also been reported by Baeyertz, Craig and Bumps'2 in steel broken under impact. % Some micrographs published by Irwin3 may possibly be interpreted as showing discontinuous brittle cracks. This paper presents additional observations of the authors on discontinuous crack propagation under various conditions. Impact Test Specimens The impact test specimens were cut longitudinally from a steel forging containing: The heat treatment consisted of oil quenching in a heavy section from 1600°F and tempering at 1260°F. The resulting yield strength was 78,000 psi, tensile strength 100,000 psi, elongation 20.0 pet in 2 in., and reduction of area 55.0 pet. Standard V-notch Charpy specimens were broken in a 217 ft-lb machine at a striking velocity of 16.8 fps. Energy absorption and fracture appearance of this material in the V-notch Charpy test are plotted as functions of temperature in Fig 1. After test, fractured halves of specimens appearing 0, 40, 80, and 100 pet fibrous (to the unaided eye) were electroplated with nickel, sectioned longitudinally (perpendicular to the notch at its midpoint), polished and etched with Cohen-Hurlich-Jacobson (C-H-J) reagent (picric acid plus Zephiran chloride in ethyl ether)4 or with Vilella reagent (1 pet picric plus 5 pct hydrochloric acid in ethyl alcohol).5 Fig 2 and 3 show cracks near the path of final fracture in the specimen rated 0 pct fibrous. Many of the cracks terminate at the boundaries of ferrite grains, some at boundaries of pre- existing austenite gzains. * A crack often starts near the end of another. Cracks within the same ferrite grains are parallel or approximately parallel in several cases. A large percentage of the cracks are branched. Fig 4 illustrated a group of cracks in the 40 pct fibrous specimen. Branching and parallelism are well marked. No more than three directions of crack have been observed on the polished surface in one ferrite grain. This is consistent with the evidence6 that brittle fracture of ferrite takes place on the cube face crystallographic planes: the {100} planes. The appearance of some cracks suggests that they have passed around a projecting corner of a second ferrite grain by going outside the plane of polish. In Fig 5 cracks in the 80 pet fibrous specimen may be observed. Some of

Jan 1, 1950

By M. D. Hassiallis

The claim is made in a number of patents1'2'3'4 that some compounds of the class known as aryl sulphides have collector properties. One of these patents generalizes the claim to include all aryl sulphides, whose generic formula is R-S2-R' (where x = 1,2, . . . ), with the restriction that if the aromatic radicals R, R' contain substituent groups these groups may not contain nitrogen or oxygen. Moses, Hess, and Perkins cite as evidence for their claims the results of flotation tests on Anaconda and Miami copper ores using diphenyl sulphide, ditolyl disulphide and dinapthyl disul-phide as collectors. The use of alkyl sulphides as collectors has also been reported5 with the conclusion that the alkyl sulphides are better collectors than the corresponding aryl sulphides. The experimental work cited appears to confirm this contention. In order to test these claims with respect to diphenyl sulphide, a sample, purchased from the Eastman Kodak Co., was tested against Anaconda ore. The procedure followed. was that of Moses, Hess, and Perkins. A sample of ore weighing 500 • grams was placed in a laboratory ball mill. To this was added 220 grams of water, 0.06 grams of commercial diphenyl sulphide (1/4 lb. per ton of ore), and 0.8 grams of lime (3 lb. per ton of ore). The material was ground until 93 per cent passed a 65-mesh screen. This pulp was diluted to 16 per cent solids. A sample of the diluted pulp was placed in a Minerals Separation type of laboratory flotation cell. After a a-min. agitation period, pine oil was added and the froth collected for a period of 15 min. This test recovered 68 per cent of the copper, with a ratio of concentration of 6.8:I. The tailing assay was 0.3 per cent Cu. Moses, Hess and Perkins attained a recovery of 75 per cent, with a ratio concentration of I2:I. Although these results do not compare too well with those of Moses, Hess and Perkins, subsequent tests showed an improvement, as judged by vanning of the tails. It is concluded, therefore, that the patent results are confirmed. Contact-angle Tests In order to study the response of the various minerals, found in Anaconda ore, to commercial diphenyl sulphide, some contact-angle tests were made. Polished particles of bornite, chalcodte, chalco-pyrite, pyrite and quartz were conditioned for 15 min. in a suspension of diphenyl sulphide in water. The concentration of this suspension was 0.284 grams per liter, this being the concentration of this reagent in the ball mill. The conditioned particles were rinsed with water (not rubbed with filter paper or boiled linen) and then tested against an air bubble in the bubble machine, with the following results: born-

Jan 1, 1943

By J. M. De La Garza Cárdenas

The total production of oil in Mexico in 1942 was 34,715,547 bbl.; that is, 8,179,254 bbl. less than the amount produced in 1941. The daily average for 1942 was 95,111 bbl., while that for 1941 was I17,520 barrels. The reduction of 22,409 bbl. per day in production was due to a decrease in exports because of the scarcity of tankers. This reduction has affected principally the Northern and Southern districts of the Tampico area; in December the Northern district (Panuco) was producing less than zoo0 bbl. per day with 445 wells shut down and the Southern district (GolJen Lane) less than $000 bbl. per day with 140 wells shut down. Drilling.—During the year 14 wells were drilled in Mexico, of which five were productive. Seven dry holes were drilled in Ebano, Tampico Northern district, in search for new producing fractures; plans are being made to explore this area by means of resistivity measurements. Three producing wells were completed in Poza Rica. Drilling in this important field will continue during 1943 to determine its extension to the west. In the Isthmus of Tehuantepec no wells were completed. Two gas wells were completed in northeastern Mexico. Wildcats.-—Two wildcat wells were completed during the year, to test the extension of the Golden Lane to the south; both were unproductive. In the Isthmus a deeper sand was found in the El Plan field* This discovery has made an important increase in the reserves in this field and will allow an increase in the production of the area during 1943. In December, three exploration wells were being drilled, two in the Tampico area and one in the Isthmus. Operating Technology.— Satisfactory progress has been made in Mexico in the application of petroleum engineering to the development and operation of the oil fields. Mud control is now an established practice and has lessened the number of fishing jobs and has allowed more open hole to be carried than formerly was possible. During 1942 the first effective use was made of determinations of bottom-hole pressure, and other modern production practices such as gun-perforating and squeeze-cementing are being introduced. Plans for 1943 The oil production during 1943 is expected to be slightly larger than that of 1942, especially if tankers are available for exporting crude and refined products. The Government proposes to increase exploration and drilling activities to increase the reserves and potential production of the country; about 50 wells will be drilled during the year, including wildcat wells in northeastern Mexico, Tampico and Isthmus areas and exploitation wells in the Ebano-Panuco, Poza Rica, El Plan and Cuichapa fields. Acknowledgment Mr. A. Barnetche, of the Production Department, "Petr6leos Mexicanos," assisted the writer in the preparation of the statistical data.

Jan 1, 1943

By M. D. Hassiallis

The claim is made in a number of patents1'2'3'4 that some compounds of the class known as aryl sulphides have collector properties. One of these patents generalizes the claim to include all aryl sulphides, whose generic formula is R-S2-R' (where x = 1,2, . . . ), with the restriction that if the aromatic radicals R, R' contain substituent groups these groups may not contain nitrogen or oxygen. Moses, Hess, and Perkins cite as evidence for their claims the results of flotation tests on Anaconda and Miami copper ores using diphenyl sulphide, ditolyl disulphide and dinapthyl disul-phide as collectors. The use of alkyl sulphides as collectors has also been reported5 with the conclusion that the alkyl sulphides are better collectors than the corresponding aryl sulphides. The experimental work cited appears to confirm this contention. In order to test these claims with respect to diphenyl sulphide, a sample, purchased from the Eastman Kodak Co., was tested against Anaconda ore. The procedure followed. was that of Moses, Hess, and Perkins. A sample of ore weighing 500 • grams was placed in a laboratory ball mill. To this was added 220 grams of water, 0.06 grams of commercial diphenyl sulphide (1/4 lb. per ton of ore), and 0.8 grams of lime (3 lb. per ton of ore). The material was ground until 93 per cent passed a 65-mesh screen. This pulp was diluted to 16 per cent solids. A sample of the diluted pulp was placed in a Minerals Separation type of laboratory flotation cell. After a a-min. agitation period, pine oil was added and the froth collected for a period of 15 min. This test recovered 68 per cent of the copper, with a ratio of concentration of 6.8:I. The tailing assay was 0.3 per cent Cu. Moses, Hess and Perkins attained a recovery of 75 per cent, with a ratio concentration of I2:I. Although these results do not compare too well with those of Moses, Hess and Perkins, subsequent tests showed an improvement, as judged by vanning of the tails. It is concluded, therefore, that the patent results are confirmed. Contact-angle Tests In order to study the response of the various minerals, found in Anaconda ore, to commercial diphenyl sulphide, some contact-angle tests were made. Polished particles of bornite, chalcodte, chalco-pyrite, pyrite and quartz were conditioned for 15 min. in a suspension of diphenyl sulphide in water. The concentration of this suspension was 0.284 grams per liter, this being the concentration of this reagent in the ball mill. The conditioned particles were rinsed with water (not rubbed with filter paper or boiled linen) and then tested against an air bubble in the bubble machine, with the following results: born-

Jan 1, 1943

By E. B. Brauer, B. F. Pennington, E. W. Hough, G. L. Stegemeier

Interfacial tension divided by the difference in density between the liquid and the vapor phases was determined experimentally by the pendant drop method on several isotherms in the two phase region below the critical point for the methane-normal decane system. The density difference data of Sage and Lacey was used in the calculation of interfacial tension. Both interfacial tension and and interfacial tension divided by density difference were found to vanish at the critical point. Interfacial tensions of less than one dyne/centimeter were observed as far as 1,000 pounds per square inch below the critical pressure. EXPERIMENTAL PROCEDURE The interfacial tension divided by the density difference for the methane-normal decane system was determined at the 100°, 130°, 160' and 190°F isotherms, from pressures of about 1,000 psi to the critical pressure, which is more than 5,000 psi for these isotherms. Particular emphasis was placed upon the investigation at pressures slightly below the critical pressure where the interfacial tension is less than 0.5 dyne/cm. Volumetric properties in the two-phase region, including the critical pressures and temperatures, were taken from the work of Sage and Lacey.1 The experimental pendant-drop technique used for the determination of interfacial tensions at high pressures incorporated the ideas of Michaels and Hauser,2 Hough, et a1,3 Walker4 and Heuer.5 In addition, the technique for determination of extremely small interfacial tension by Jennings6 was utilized in the region near the critical points. A detailed description of the apparatus is given in a dissertation by one of the authors.7 Cleaning operations on the stainless-steel sample system included successive washings with chromic acid, tap water and, finally, distilled water. Subsequent cleanings were performed with re-distilled normal pentane, which had an extremely low residue upon evaporation. Specific composition requirements necessitated a fairly precise sample introduction — although, fora two-phase, two-component system, the composition of each phase is completely determined if pressure and temperature are controlled. The normal decane was delivered into the evacuated sample system as a liquid from a burette. The methane was then introduced into the system from a calibrated isothermal container, so that pressure differentials could be used to determine the amount introduced. High pressures were obtained by compressing the sample with a mercury injection pump until the critical pressure was reached for the particular isotherm being studied. Experimental data were then obtained for specific pressures by first decreasing the pressure slightly so that two phases would appear, and then photographing a drop at that pressure. Subsequent photographs were made at increments throughout the pressure range. Calculation of interfacial tension divided by density difference was made from measurements

By J. M. De La Garza Cárdenas

The total production of oil in Mexico in 1942 was 34,715,547 bbl.; that is, 8,179,254 bbl. less than the amount produced in 1941. The daily average for 1942 was 95,111 bbl., while that for 1941 was I17,520 barrels. The reduction of 22,409 bbl. per day in production was due to a decrease in exports because of the scarcity of tankers. This reduction has affected principally the Northern and Southern districts of the Tampico area; in December the Northern district (Panuco) was producing less than zoo0 bbl. per day with 445 wells shut down and the Southern district (GolJen Lane) less than $000 bbl. per day with 140 wells shut down. Drilling.—During the year 14 wells were drilled in Mexico, of which five were productive. Seven dry holes were drilled in Ebano, Tampico Northern district, in search for new producing fractures; plans are being made to explore this area by means of resistivity measurements. Three producing wells were completed in Poza Rica. Drilling in this important field will continue during 1943 to determine its extension to the west. In the Isthmus of Tehuantepec no wells were completed. Two gas wells were completed in northeastern Mexico. Wildcats.-—Two wildcat wells were completed during the year, to test the extension of the Golden Lane to the south; both were unproductive. In the Isthmus a deeper sand was found in the El Plan field* This discovery has made an important increase in the reserves in this field and will allow an increase in the production of the area during 1943. In December, three exploration wells were being drilled, two in the Tampico area and one in the Isthmus. Operating Technology.— Satisfactory progress has been made in Mexico in the application of petroleum engineering to the development and operation of the oil fields. Mud control is now an established practice and has lessened the number of fishing jobs and has allowed more open hole to be carried than formerly was possible. During 1942 the first effective use was made of determinations of bottom-hole pressure, and other modern production practices such as gun-perforating and squeeze-cementing are being introduced. Plans for 1943 The oil production during 1943 is expected to be slightly larger than that of 1942, especially if tankers are available for exporting crude and refined products. The Government proposes to increase exploration and drilling activities to increase the reserves and potential production of the country; about 50 wells will be drilled during the year, including wildcat wells in northeastern Mexico, Tampico and Isthmus areas and exploitation wells in the Ebano-Panuco, Poza Rica, El Plan and Cuichapa fields. Acknowledgment Mr. A. Barnetche, of the Production Department, "Petr6leos Mexicanos," assisted the writer in the preparation of the statistical data.

Jan 1, 1943

By H. W. Hindry

This paper presents the ingredients com-~osing a type of oil-base mud that has been successfully used in drilling oil horizons in California, the effect of ingredient concentrations on physical properties, methods of handling at the well and possible advantages of a waterless drilling fluid with excellent plastering properties. Introduction An oil-base mud is a rotary drilling fluid in which oil has been substituted for water as the principal liquid ingredient. In recent years such a mud has been developed and used successfully for drilling the oil horizons of wells in various Calilornia fields. There are several types of oil-base mud, but only the type that is currently used to any appreciable extent will be considered at this time. The oil-base drilling-mud compositions used by Shell Oil Company, Incorporated have been covered by several patent applications on which patents are expected to issue at an early date. The purpose of this paper is to present data on the fundamental design of the mud; the ingredients used and their specifications; the effect of ingredient concentration on physical properties; the selection of the proper mud; the facilities needed for handling the mud; and a general discussion on drilling with oil-base mud. In view of the early stage of development of oil-base mud, the great number of vari- ables, and the almost unlimited possible combinations of these. variables, which in turn require extensive laboratory study, there are certain irregularities and omis. sions in the data presented here. However, it is believed that sufficient data are at hand to permit a fairly complete analysis of the characteristics of oil-base muds. In view of the excellent plastering properties of oil-base mud when properly proportioned, its use should: (I) minimize the possibility of impairing the natural flow potentialities of the producing horizon such as that resulting from infiltration of water from water-base muds; (2) permit smaller clearances for setting liners, since the mud sheath has no appreciable thickness; (3) eliminate the possibility of clogging the perforations of the liner with thick mud sheath; (4) facilitate the removal of the mud sheath from the walls of the hole, for its mud sheath has no appreciable strength; (5) assist in drilling through formations, such as "heaving shale," where water wetting appears to be a source of difficulty. (6) permit cores to be obtained without contamination from drilling water. Fundamental Design of an Oil-base Mud In the design of any rotary drilling mud it is necessary to select materials that will fulfill the following requirements: (I) act as the liquid medium and regulate the viscosity; (2) impart initial and final plastering properties; (3) give gel strength and structure in order to prevent settling; (4) serve as a weighting material. The

Jan 1, 1941

By H. W. Hindry

This paper presents the ingredients com-~osing a type of oil-base mud that has been successfully used in drilling oil horizons in California, the effect of ingredient concentrations on physical properties, methods of handling at the well and possible advantages of a waterless drilling fluid with excellent plastering properties. Introduction An oil-base mud is a rotary drilling fluid in which oil has been substituted for water as the principal liquid ingredient. In recent years such a mud has been developed and used successfully for drilling the oil horizons of wells in various Calilornia fields. There are several types of oil-base mud, but only the type that is currently used to any appreciable extent will be considered at this time. The oil-base drilling-mud compositions used by Shell Oil Company, Incorporated have been covered by several patent applications on which patents are expected to issue at an early date. The purpose of this paper is to present data on the fundamental design of the mud; the ingredients used and their specifications; the effect of ingredient concentration on physical properties; the selection of the proper mud; the facilities needed for handling the mud; and a general discussion on drilling with oil-base mud. In view of the early stage of development of oil-base mud, the great number of vari- ables, and the almost unlimited possible combinations of these. variables, which in turn require extensive laboratory study, there are certain irregularities and omis. sions in the data presented here. However, it is believed that sufficient data are at hand to permit a fairly complete analysis of the characteristics of oil-base muds. In view of the excellent plastering properties of oil-base mud when properly proportioned, its use should: (I) minimize the possibility of impairing the natural flow potentialities of the producing horizon such as that resulting from infiltration of water from water-base muds; (2) permit smaller clearances for setting liners, since the mud sheath has no appreciable thickness; (3) eliminate the possibility of clogging the perforations of the liner with thick mud sheath; (4) facilitate the removal of the mud sheath from the walls of the hole, for its mud sheath has no appreciable strength; (5) assist in drilling through formations, such as "heaving shale," where water wetting appears to be a source of difficulty. (6) permit cores to be obtained without contamination from drilling water. Fundamental Design of an Oil-base Mud In the design of any rotary drilling mud it is necessary to select materials that will fulfill the following requirements: (I) act as the liquid medium and regulate the viscosity; (2) impart initial and final plastering properties; (3) give gel strength and structure in order to prevent settling; (4) serve as a weighting material. The

Jan 1, 1941

By Victor A. Phillips

A series of strips of a Ni-12.7 at. pct A1 alloy were Prepared containing cubical y'(NisAl) precipitates with edge lengths from 60 to 500A. A particle-free solution-tveated strip was included for cornparison. They weve cold-rolled 95 pct and the effects of particle size on the isochronal (1/2 hr) annealing behavior between 300° and 950°C studied (by hardness and light and electron microscopy). It ulas inferred that the particles deformed with the lnatvix becoming lamellae which remained coherent. Comparison with published data fov pure nickel showed that aluminum greatly re-tavded softening and recrystallization, but it made little difference whether or not particles were present. The presence of pakticles led to a heterogeneous distribution of precipitates after annealing at 700" to 750°C. Recovery was not detected. Recrystallization occurred by the growth of new grains into unrecrys-tallized material. In a previous study by the author,' the growth of Ll2-type ordered yl(Ni3Al) precipitates was followed in Ni-12.7 at. pct A1 alloy as a function of aging at 600" and 700°C. The particles were showo to be cubical in shape in all sizes from 50 to 3000A and remained coherent. This work was used as a guide in preparing the starting structures for the present study of the effect of these particles on the annealing behavior of heavily cold-rolled strip. Another question of present interest was whether dislocation and particle hardening were additive, since the structures before rolling ranged from solution-treated to peak-aged to overaged. Also, precipitation might occur on annealing after cold-rolling. Reference may be made to other papers2"5 for previous work in this relatively unexplored field and only some recent work will be mentioned her:. phillips2 studied the effect of deformable 0 to 590A-diam cobalt particles on a Cu-3.23 pct Co alloy rolled 95 pct and found that the particles, which rolled out into thin lamellae, impeded softening and recrystallization. Tanner and servi3 likewise studied the annealing of cold-swaged Cu-2 pct Co alloy containing 150A-diam particles and found impeding effects. Haessner et a1.,4 on the other hand, found that incoherent 2-p-diam non-deformable particles of B4C (0.04 vol pct) tended to increase the rate of recrystallization of copper rolled up to 95 pct reduction. They attributed this to the formation of new grains at the particle interfaces. Humphreys and artin' found that nondeformable silica particles in copper rolled to 30 pct reduction accelerated recrystallization if the particle spacing was large and retarded it if the spacing was smaller. Haessner et a1 4 also studied a rolled Ni-Cr-A1 alloy; however, the particles of y'(Ni3Al)-type precipitate were not put in before rolling, but separated during the isothermal annealing at 750°C. No previous work appears to have been carried out on the effect of y' (Ni3A1) particles on the annealing of Ni-A1 alloy. Hornbogen and ICreye7 redetermined the solubility c of aluminum in nickel as a function of temperature T and showed that it was given by c = 32.6 exp(-1940/RT). This relation gives aluminum solubilities of 15.1, 14.2, 12.0, and 10.7 at. pct at 1000°, 900°, 700°, and 600°C, respectively. The phase precipitated from the nickel-rich solid solution is fcc y1 (Ni3A1) which has a Cu3Au -type ordered structure8 and remains ordered up to 1000°C.B EXPERIMENTAL PROCEDURE The alloy used was identical with that used before. Chemical analysis showed 6.27 wt pct (12.71 at. pct) Al, the principle impurities being 0.065 pct Fe, 0.022 pct Co, 0.020 pct Cu, and 0.004 pct C. Bar stock of 1 in. diam was cold-swaged to % in. diam, cold-rolled to 0.300-in.-thick strip, and annealed at 900°C in dry hydrogen. It was cold-rolled to 0.100-in. thickness and solution-treated for 1 hr at 1000°C while sealed in a quartz tube in argon, quenching in iced brine with the aid of a device to snap off the nose of the tube. Lineal analysis gave an average grain size of 0.055 mm. Pieces of strip were aged at 700°C in vacuo for 30 min, 51/4 hr, and 1 week to produce nominal average particle widths of 60, 150, and 500A, respectively, as known from the previous work.' The average diamond pyramid hardness was determined. The heat-treated strips were rolled from 0.100 to 0.005 in., a reduction of 95 pct, and the rolled strips stored at about -5°C. Small pieces were annealed within 1 week for 30 min at temperatures from 300° to 950° ±2°C in a horizontal vacuum furnace. Strips were withdrawn into a cooling zone, giving an estimated initial cooling rate from 950°C of about 50°C per sec. Average diamond pyramid hardnesses were determined on a lightly electropolished spot on the surface of each strip using 300-g load. Each point on the softening curves represents a separate annealed specimen. Sections containing the rolling direction were examined by optical metallography. Selected specimens were electrothinned to the center plane' and examined by transmission at 100 kv in a Siemens Elmiskop I electron microscope. It is well-known that changes in the structure tend to occur when a deformed strip is electrothinned below a thickness of a few hundred angstroms, although this is less serious with a material such as nickel which has a high melting point, and also is apt to be less serious when particles are present. Observations were nevertheless confined to thicker regions of the foils with estimated thicknesses over 1000A. No changes were observed due to beam exposure.

Jan 1, 1968

On the following pages are abstracts of papers published by the Institute during the year 1932 as Technical Publications, Preprints, in bound volumes and in Mining and Metallurgy. For abstracts of papers that appear in bound volumes in 1932 but that were published as Technical Publications in 1930 or 1931, see the Transactions for those years. Papers that appear in this volume are not abstracted here. Many of the Technical Publications have been reprinted in bound volumes. Information regarding this disposition, and number of pages in each paper, may be found in the list beginning on page 309. Volume numbers are given as listed on page 3 and in the paragraph at the beginning of the index, page 315. The abstracts are grouped as follows: Page Page Metal Mining.................... 265 ferrous Alloys)................. 279 Milling and Concentration......... 268 Coal Division.................... 287 Iron and Steel Division............ 270 Petroleum Division............... 292 Nonferrous Metallurgy (Reduction Nonmetallic Minerals............. 299 of Ores)....................... 277 Mining Geology.................. 301 Rare Minerals and Metals......... 279 Mining Administration (Accounting, Institute of Metals Division (Found- Taxation, Industrial Relations). . 304 ing and Metallography of Non- Geophysical Prospecting........... 304 Metal Mining The Mineral Industry. By Scott Turner. (Min. & Met., June, 265. 3500 words.) Abstract of an address delivered before the Royal Canadian Institute, Toronto, April 16, briefly outlining the importance of mining in the United States, in Canada, and in the world. Comparison is made of the mineral production for 1886, 1900, 1910, 1920 and 1929, showing that in the 43 years from 1886 to 1929 that of the world increased nearly tenfold, of the United States over twelvefold and of Canada thirtyfold, but that Canada's output was equivalent to only 2 per cent of the world total and to 5 per cent of that of the United States in 1929. Statistical tables and graphs show value of production, percentage of world production contributed by Canada and the United States, etc. The mining situation in Canada is briefly reviewed: only those American engineers who have had occasion to examine the figures appreciate the rapidity of growth of Canadian mineral production. The treatment of minerals involves vast complex industries. When we are producing, say, 6 billion annually, the employment of 2 million workers provides indirect support to perhaps 10 million people. Exploiting mineral deposits is peculiar in certain ways, for the deposits are exhaustible, are of rare occurrence when measured in terms of outcrop area compared to total earth area, and may suddenly be handicapped or superseded by new discoveries; moreover, the economic position of the contained metals is 'affected by the use of scrap metal and the existence of invisible stocks. The largest and most valuable of the mineral deposits are not the metals, but rather the fuels. The record of the coal industry in recent years is one of brilliant technical achievement; its economic position is far from satisfactory. A so-called world fuel

Jan 1, 1932

By John W. Cahn, John E. Hilliard

Single crystals of copper and silicon-iron were cold rolled in orientations chosen to produce individually the major components of the poly crystalline deformation texture. The orientation dependence of the recrystallization kinetics was studied relative to the primary recrystallization textures of these specimens. It is not possible to rationalize the poly crystalline re crystallized textures on this basis. The results suggest an important role of the interaction of adjacent crystals during the deformation of aggregates. BRICK and Williamson1 first noted evidence that the recrystallization temperature was different for straight-rolled and cross-rolled copper given comparable reductions. Michalak and Hibbard2 investigated quantitatively the effect of rolling procedure on the kinetics of recrystallization of cold-rolled copper and found that material cold-rolled the same amount by straight-pass, cross-pass, and compression-pass techniques developed different deformation and recrystallization textures, different 1-hr recrystallization temperatures, and different recrystallization kinetics. However, the temperature dependence of the rate of recrystallization was essentially the same for all techniques. Similar results were obtained on iron. Dunn and Koh3 in studying the recrystallization textures of cold-rolled silicon-iron single crystals reported large differences in the annealing temperatures and times required to recrystallize specimens of different orientations cold-rolled the same amount. Liu4 and Liu and Hibbard5 utilized the concept of different recrystallization temperatures for different orientations of cold-rolled crystals to rationalize the difference in recrystallization textures found in various face-centered-cubic metals. Their explanation predicted a significant difference in the recrystallization kinetics of deformed (110) [112] crystals as compared to (358) [352] crystals, and, in fact, Liu4 reported evidence that this difference existed at least qualitatively. Verbraak6 who rolled and recrystallized a series of copper single crystals found that the double (112) [111] rolled orientation is related to recrystallized cube texture formation. The effect of rolling intensity on the relative amount of cube component suggests an important role of recrystallization kinetics. Walter and Hibbard7 while trying to relate the behavior of rolled and recrystallized single crystals of silicon-iron to the behavior of polycrystal-line silicon-iron again noted that differences in recrystallization kinetics were necessary to rationalize their results. The purpose of the present investigation was to obtain quantitative kinetic data on the recrystallization of single crystals of both copper and silicon-iron rolled to initial isolated individual orientations corresponding to those found in the polycrystalline deformation textures. These data might indicate the importance of the deformation orientation, i.e. the range of available nuclei, the deformed matrix orientation into which these nuclei grow, and the orientation dependence of their growth rate during primary recrystallization on this texture. I. COPPER Experimental Procedure—A single crystal of 99.98 pet purity copper, grown by the Bridgman technique, was purchased in the form of a bar 1 1/2

Jan 1, 1962

By J. Mizrahi, A. M. Baniel, A. Mitzmager, S. Star

This article gives an account of the latest developments in the use of TBE for sink-float separation of silicate minerals. A number of minerals for which the process has been tested and found suitable are reviewed. Specific examples are discussed in relation to the particular problems of sink-float separation and recovery of TBE as compared with non-silicate minerals. The economic aspects are outlined. Silica and silicates comprise the most common and abundant group of minerals, and since they are present in variable amounts in most ores, they constitute an appropriate subject for the review and discussion of the recent developments in the use of TBE for mineral concentration. The silicates considered as a group have an extremely wide range of chemical and physical properties. Some of these properties, which are common to all minerals, are of importance to concentration by TBE and are discussed in some detail in this paper, as well as the development of methods and apparatus for concentration and recovery of TBE and several examples of concentration of silicates. PROPERTIES OF MINERALS WITH RESPECT TO CONCENTRATION BY TBE The properties considered as most important to concentration by TBE are specific gravity, structure, surface and shape. The specific gravity of a mineral is a fundamental property and is constant between very close limits for the same species of different sources if particles are pure and free from cavities or cracks. In many species, however, solid inclusions and changes in chemical composition due to replacement of elements cause variations in the specific gravity. The plagio-clase series of feldspars between albite and anorthite illustrate this point (specific gravity from 2.60 to 2.77). Fig. 1 shows the specific gravity distribution of some of the common silicate minerals.' The highest specific gravity is about 4.7 (zircon) and the lowest is 2.0 (sepiolite), with most of them ranging between 2.6 and 3.5. Although most of the silicates given in Fig. 1 are found as constituents of rocks, those generally considered as rock making minerals are comparatively few. They include quartz, feldspars, nephelite, sodalite, leucite, mica, pyroxenes, amphiboles, chrysolite, kaolin, talc and serpentine. These minerals may appear in igneous rocks as coarse crystals in granites, syenites and diorites or as very fine grained dispersions in basalt and felsite. When the latter rocks occur in an ore, their specific gravities depend on the minerals present and structure. The same is true for the sedimentary and metamorphic rocks (sandstones, shales, gneiss, slate, schists). A comparison of specific gravities for the minerals listed in Fig. 1 with that of TBE (see Table I) shows that the important rock-forming minerals, with the exception of pyroxenes, amphiboles and chrysolite (olivine), lie in the specific gravity range of less than 2.96 and can therefore be separated by TBE. The ore structure is important both in determining the apparent specific gravity and the efficiency of TBE recovery. The structure can be compact (as in

Jan 1, 1963

By Robert E. Green

Formulae are given for calculating the modes of wave propagation in a single-crystdl specimen possessing a given crystallographic orientation. Such calculations lead to determination of the orientation factor appearing in the Granato-Lucke theory for the attenuation of these waves due to dislocation damping. A detailed treatment is given for the case of an aluminum crystal possessing the orientation having a maximum Schmid fac -tor of 0.5. FOR a number of years the attenuation of ultrasonic waves propagating in metals has been used to investigate various phenomena causing internal friction.Most of the experiments were performed on polycrystalline test specimens and the waves were assumed to be propagating in an isotopic medium. However Alers 6 in 1955 and more recently Hikata et at. Chiao and Gordon,8 and Swanson and Green 10 have used measurements of attenuation of ultrasonic waves to study internal-friction changes in single crystals. These authors were concerned with the energy losses experienced by the ultrasonic waves due to dislocation motion induced by plastic deformation of the crystals. Alers measured the attenuation of 7 mc per sec ultrasonic pulses propagating in zinc single crystals before, during, and after plastic deformation. Simultaneously he measured the time-dependent plastic strain at constant stress in order to study the correlation between this strain and attenuation. The crystals were oriented in such a way that the applied stress provided a direct shear on the slip plane, thus causing the deformation to proceed by slip on this plane. At the same time the high-frequency sound pulses were sent through the crystal perpendicular to the slip plane. He found that the attenuation of transverse waves, the stress vectors of which lie in the slip plane, was very sensitive to the deformation. The polarization of the particle displacements, associated with these waves, relative to the applied static shear stress, and hence the direction of slip, had no obvious effect on the results. The attenuation of longitudinal waves was affected by the deformation only when the slip plane was not perpendicular to the propagation direction. This indicated that the attenuation was caused by dislocations introduced by the deformation and moving only in the slip plane. Hikata et al. made simultaneous measurements of attenuation, velocity changes, and stress-strain relations on aluminum single crystals deformed in tension. Both longitudinal and shear waves were used, at frequencies of 10 and 13 mc per sec. They placed emphasis on the choice of propagation modes and polarization of the ultrasonic waves, such that interactions between these waves and dislocations on selected slip systems could be investigated. They also selected specimens possessing specific crys-tallographic orientations, which allowed investigation as a function of the number of equally favored slip systems under the applied stress. They found that, for symmetrical orientations, the change of attenuation decreases with the increasing number of equally favored slip systems, i.e., in the order

Jan 1, 1964