Search Documents

Jan 1, 1937

By W. D. Ludemann, J. E. Dor, L. A. Shepard

Recovery of the creep resistance of 99.99 pct pure Al was studied at temperatures 540°, 573°, 600°, and 611°K. Poly-crystalline specimens crept under a stress of 950 psi to a strain of 5.5 pct were allowed to recover for periods of from 1 min to 16 days under a residual stress of 4.4 psi. Increased creep rates upon reapplication of the 950 psi stress evidenced softening of the material. The activation energy for the recovery process was found to be 64,000 cal-per mol. THREE major observations have clearly revealed that the creep of polycrystalline aluminum above about 510°K is controlled by the rate of climb of jogged edge components of dislocations past the barriers impeding their motion: 1) Extensive polygonization, characteristic of climb, takes place during creep.'9' 2) The activation energy for creep equals the estimated activation for self-diffusion. 3) The stress law for creep coincides with theoretical predictions based on the climb mechanism.4,5 The decreasing rate during the primary stage of creep must be ascribed to the introduction of additional barriers to the glide of dislocations. During secondary creep the density of barriers must remain constant, the rate at which new barriers are formed being equal to the rate at which they recover. For this reason the nature of the barriers, and their rates of formation and recovery, are significant to a complete understanding of creep. It is proposed here to study the kinetics of the recovery of barriers to creep of high-purity polycrystalline aluminum in the climb range. The technique will consist of creeping a series of tensile specimens under a prescribed stress to given state following which the specimens will be recovered for various times and temperatures under approximately zero stress. The amount of recovery will be determined by comparing creep curves following the recovery. EXPERIMENTAL PROCEDURE The material used for this investigation was a 99.99 pct pure Al supplied by the Aluminum Co. of America in sheets of 0.001-in. thickness having an H-18 temper. The spectroscopic analysis of impurities gave Cu-0.004 wt pct, Fe-0.002 pct, Si-0.001 pct, others-0.000 pct. Creep specimens were machined with their tensile axes in the rolling direction of the sheets. Annealing in a molten potassium nitrate-potassium nitrite bath for 1 hr at 686K, followed by air-cooling, resulted in a grain diameter of from 0.22 to 0.27 mm. Creep machines were equipped with constant stress lever arms of the type suggested by Fullman, Carreker, and Fishher,' which maintained the applied stress to within 0.04 pct of the reported value of 950 psi. Creep strains were calculated from extensions over a 6-in. gage section to the nearest 3 X 10"5. The temperatures of testing, 540°, 573", 600°, and 611°K, were obtained by immersing the specimen and extensometer assembly in a molten KNO2-KNO3 bath. Temperatures during the periods of creeping could be maintained constant to within better than ± 1°K. Correlation of creep data at different temperatures of testing demanded the use of an appropriate temperature-compensated time 8. Previous investigations have shown that the creep of pure metals at temperatures above about 0.55 of their melting temperatures can be correlated by the functional relationship3" e=f(0), s= const. [1] where e = total plastic strain during creep f = a function that depends on stress a = stress 6 = te-Q/RT = a temperature-compensated time t = time under test Q = 35,500 cal per mol = activation energy for creep R = gas constant, and T = absolute temperature In the present series of tests all of the creep was conducted under the same stress of 950 psi. To provide identical initial conditions for the recovery all specimens were first crept to a temperature-compensated time of = 47 X 10-14 min which resulted in a creep strain of 0.055 + 0.005 regardless of the creep temperature. During recovery, a small stress (4.4 psi) was permitted to remain upon the specimens to maintain tautness in the pulling assembly and to prevent mechanical damage to the soft specimen. After each recovery period, the full stress was reapplied and

Jan 1, 1961

By Arnulf Muan, W. C. Hahn

Activities of "FeO" in "FeO"-MgO solid solutions have been determined in the temperature interval 1100" to 1300"C by equilibrating oxide samples with pure metallic iron in atmospheres of known oxygen partial pressures. The end members "FeO" and MgO form a complete solid solution series. The system shoztls a considerable positive deviation from Raoult's law. A large amount of data has been accumulated during the past 50 years on stability relations existing among various crystalline and liquid phases in oxide systems of importance in metallurgical processes. By comparison, very little is known about the thermodynamic properties within the various homogeneous phases present in the systems, particularly the crystalline phases. The present paper deals with determination of activities as a function of composition in solid solutions of wüstite ("FeO") and periclase (MgO). Such solid solutions ("Magnesiowustites") have simple sodium chloride structure and are known to be continuous between the end members at elevated temperatures (> 1000°C) and strongly reducing conditions such as prevail in contact with metallic iron. Wiistite has a defect structure in which the ratio of oxygen to iron varies and never has as low a value as 1:1 corresponding to the simplified formula FeO. Within the range of stability of this phase, the composition changes between a maximum oxygen content of approximately 25.6 wt pct (corresponding to the formula FeO.83O) and a minimum oxygen content of approximately 23.2 wt pct (corresponding to the formula Fe0-96O). The activity data to be reported in the present paper are based on using as standard state the wüstite which is in equilibrium with metallic iron at a particular temperature, i.e., "FeO" of minimum oxygen content at each temperature. For sake of simplicity, the formula FeO will be used to represent the wustite phase in the remainder of this paper. Consider the reaction 2 FeO solid solution = 2 Femeta1 + Ozgas in which FeO dissolved in another oxide dissociates to metal and gas. The activity of FeO in the solid solution, relative to "pure FeO" in equilibrium with metallic iron as a standard state, is then expressed as Here Po, and po2 * are the partial pressures of oxygen of the gas phase in equilibrium with metallic iron and the oxide solid solution or "pure FeO", respectively. The equation holds only if the metal phase is essentially pure Fe. The oxide combinations used in the present investigation fulfill this requirement. Magnesia is so much more stable than FeO that for all practical purposes aFe = 1 in the metal phase present in all mixtures used in this investigation. I. EXPERIMENTAL METHOD 1. General Procedure. The experimental method used was analogous to that developed by Foster and Welch1 and used recently by Hahn and Muan.2 It consisted of four steps: a) Determination of the equilibrium between FeO and Fe. b) Determination of d-spacing change with composition in oxide solid solutions (FeO-WO). c) Equilibration of various members of the solid solution series with a metal phase and a gas phase of known oxygen partial pressure. d) Determination of compositions of solid solutions resulting from step (c) by means of data obtained in step (b). 2. Starting Materials. General Aniline and Film Corp. carbonyl iron powder, type HP, was used as the source of metallic iron. A representative analysis was as follows: Fe, 99.6 pct; C, 0.01 to 0.04 pct; 0, 0.1 to 0.3 pct; N, 0.00 to 0.05 pct. Other elements were present as traces only. Wiistite was prepared from "Baker Analyzed" Reagent grade Fe2O3 of reported analysis as follows: Assay (Fe2O3), 98.8 pct; insoluble in HC1, 0.02 pct; not precipitated by NH,OH, 0.02 pct; Zn, 0.003 pct. Production of wüstite was achieved by a two-step

Jan 1, 1962

By Gearge C. Wallick

This paper describes experimental procedures for the calibration of capillary tubes to be employed as comparison standards in gas flow-rate measurements and considers several types of flow which were observed in the calibration of seven capillaries of varying diameter. It is shown that under certain experimental conditions deviations from Poiseuille flow are observed which may not be attributed to turbulence, and that this flow behavior may be described empirically by introducing the classical kinetic energy correction into the Poiseuille equation. INTRODUCTION Techniques have been developed for the measurement of the volume rate of flow of nitrogen through glass capillary tubes as a function both of the differential pressure applied and of the absolute gas pressure. Capillary tubes thus calibrated are frequently used to determine the rate of gas flow through a porous sample in the measurement of slip-corrected permeability. The purpose of this note is to describe the calibration procedure and to discuss some observed deviations from the ideal flow behavior predicted by the Poiseuille equation. EXPERIMENTAL PROCEDURE The volume flow rate of nitrogen as a function of the differential pressure was determined experimentally for a series of seven glass capillary tubes of varying diameter. As is shown in Table 1, the capillary radii in the series ranged from 0.004 cm for K1 to 0.07 cm for K7. The capillary tubes were cut from capillary tubing purchased on special order from several manufacturers and the bore radii were determined by microscopic measurement. The gas volume flow rate was measured for each capillary tube at a series of differential pressures in the range from 0 to 3 cm of mercury and at average absolute pressures of 1.0, 2.5, 4.0, and 6.0 atm. Experimental Procedure for Small Capillaries A schematic diagram of the apparatus used to calibrate the three smallest capillaries, Kl, K2, and K3, is shown in Fig. 1. By means of a standard Ruska Instrument Corp. volumetric pump (equipped with a synchronous motor drive, two stages of gear reduction, and a quick-change lathe gear box), nitrogen was displaced by mercury from a metal cell immersed in a constant-temperature bath. The pump, the line to the cell, and a part of the cell were filled with mercury. As mercury was forced into the cell, it displaced nitrogen which passed through the capillary tube being calibrated and into a large container with a volume of approximately 30 liters. Since the volume of this container was very large compared to the total volume change of the gas resulting from the action of the displacement pump, the absolute pressure of the system was essentially constant throughout any one run. Prior to any determination this pressure could be set at any desired level by means of an auxiliary nitrogen cylinder. The differential pressure across the capillary was measured with a Meriam Red Oil manometer and recorded together with the corresponding pump displacement rate which was equal to the gas flow rate. By repeating this process for a series of different displacement rates at each of the absolute pressures of interest, the data necessary for plotting the calibration curves for capillaries K1, K2, and K3 were obtained. All calibration measurements were made in a constant temperature room to minimize errors due to temperature fluctuations. In each run. the flow was maintained until equilibrium was established. Experimental Procedures for Large Capillaries The flow rates through Capillaries K4, K5, K6, and K7 required to obtain the pressure drops desired were larger than could be obtained from available constant displacement pumps, and it was thus necessary to employ an alternative calibration procedure. The arrangement of apparatus used in calibrating these capillaries at an average pressure of one atmosphere is shown in Fig. 2. Each capillary was calibrated by flowing nitrogen through the capillary and recording the differential pressure as a function of the flow rate. 'The differential pressure was measured with a Meriam Red Oil manometer and the flow rate was determined by collecting the effluent gas over water at constant pressure and recording the increase in volume per unit time after an equilibrium had been established. Appropriate corrections were made for the

Jan 1, 1953

By W. W. Stephen, J. P. Walsted, W. J. Kroll

FOR the production of carbides, various furnace types are available, especially those using arc, resistance, and high-frequency heating. Selection of a specific means of heating depends primarily on the material to be treated and the physical properties of the carbide produced. In the present case, zirconium carbide had to be prepared on an industrial scale as a raw material for the production of anhydrous zirconium chloride. Considering that a rather expensive pure oxide was to be used, the arc-furnace treatment recommended for zircon sands in a previous publication' was ruled out because of the considerable volatilization and dust losses caused by the blast of the arc. For this reason, either high-frequency or resistance heating seemed to offer more promise. Since there was not enough capacity of the former available, resistance heating was chosen. It was first thought that the Acheson silicon carbide furnace would be suitable for the present purpose, but the voltage in such a furnace, in which the current passes through the batch, varies from 220 to 75 v from the start to the end of a run. This variation is so great that a special tap transformer would have been required. Trouble was also expected by local melting of the carbide. Pure zirconium carbide melts at about 3527°C, but the melting point is brought down to 2427°C, according to Agte,2 when an excess of 6 pct C is present in the carbide. This we found confirmed by experiments in a high-frequency furnace. Excess carbon is needed in the batch to obtain a complete reduction. Fusion of the charge would cause great difficulties in an Acheson-type furnace because of the good electrical conductivity of the carbide as compared with that of the loose batch. Also, fused carbide is much more difficult to chlorinate than the spongy product that can be made in the radiation furnace described below. It was apparent that, to obtain a good-qual-ity zirconium carbide, the heat input would have to be well-controlled. The hairpin-resistor principle seemed to offer possibilities in this regard, and a furnace of this type was therefore developed. The advantages of the hairpin-resistor radiation principle have been discussed in previous publications, and a split-tube graphite-resistor furnace," now increasingly used in various laboratories, as well as a centrifugal quartz melting furnace4 of this type, has demonstrated the usefulness of this heating method. The hairpin-heater element has the following definite advantages over a straight resistor of the type used, for instance, by Georges:5 Its resistance is four times greater; it can expand freely; it is sturdier because of the larger diameter, and it has a larger radiation surface; there are no hot contacts that might wear out or overheat; only one clamp is used which permits assembling all electrical leads at one side of the furnace, making the other sides easily accessible to the operator. The shorter element and its larger diameter permit greater concentration of heat. The furnace developed is shown in fig. 1. The box (I), made of 2 1/2-in. graphite plates, has inside dimensions of 23x17x16 in. It contains the briquet-ted batch (2). The box is embedded in lampblack (3) up to the cover plate. The cover plate contains an opening for the gas escape (4) and for the observation hole (5), which permits measuring the temperature with an optical pyrometer. The cover plate is embedded in charcoal (6). The lampblack is contained in the insulating brick lining (7), held in the 1/4-in. sheet steel box (8). The graphite box is set on two rows of triangular graphite bars (9). The hairpin-heater element (10), the dimensions of which are given below the main drawing, extends horizontally in the graphite chamber and radiates freely on the batch. A graphite tube (11) keeps the lampblack from falling into the slot. The split electrode, which in reality is turned 90" against the drawing, is so arranged that the slot is vertical. The water-cooled packing gland (12) is insulated by an airgap from the heater element. A thin pipe (13)

Jan 1, 1951

By N. E. Rogen, N. J. Grant

WHILE direct measurements of the growth of precipitate particles during aging is of fundamental value, few such measurements have been made. Direct measurements by means of optical or electron-microscopy and X-ray techniques are preferred, however, many of the aging studies have been based on indirect methods such as electrical resistivity and hardness. Because of the minute size of most precipitate particles (less than 1000A) the light microscope is of limited use while electron microscopy is subject to slowness, etching problems and consequent resolution problems. It is fortunate that alloys of the Nimonic type, based on Ni-Cr-Ti-Al, lend themselves to accurate and relatively easy particle size measurements. With proper balance of titanium and aluminum, the only aging precipitate is the gamma prime (r') Ni3,(Al, Ti)2 phase and this phase is the basis of the high-temperature strength of these allos.3-6 The Ni3(Al, Ti) phase is a face-centered-cubic, ordered structure with nickel atoms occupying the cube faces. Titanium atoms can replace three out of every five aluminum atoms and when substituting do so preferentially.2 Electron microscopy has shown that during aging of most of the commercial alloys of this type, precipitate particles are unusually uniform in size and distribution, and that the volume of (r') phase is large (20 pct).4,7 The aim of this investigation was to measure the growth of (y') phase during aging. In so doing, it was hoped that a clearer understanding of the aging process would be attained. X-ray line broadening was used as the measure of precipitate particle size. This technique was selected because it can measure and average the diameter of thousands of particles in one operation. The variations in hardness and matrix lattice parameter with aging were also studied and related to the particle size. EXPERIMENTAL PROCEDURE An alloy of the following composition was studied: Cr Ti A1 C Ni Wt pct 20.71 2.98 1.43 0.04 bal. At. pct 22.06 3.47 2.95 0.18 bal. The alloy, a 15- lb vacuum melt, was forged to 1/2-in. diam at a temperature of 1900" to 2200°F; was solution heat treated for 4 hr at 2000°F and water quenched; and was then aged in various ways. The ASTM grain size was 4 to 5. No (7') phase could be detected by X-ray analysis after solution treatment and electrolytic extraction. Aging was performed on 2-in. long specimens at 1400°, 1500°, and 1600°F for increasing times. One-half inch sections were removed after each time increment and were then electropolished in a solution of H3P04 saturated with chromium trioxide at a potential of 30 v and rectified with a tantalum electrode. Rockwell hardness measurements were taken using one side of the polished specimen. Matrix lattice parameter determinations were made on the other side using filtered chromium radiation references with the position of the (220) line of a silicon standard. To enable the precipitate particles of the (y') phase to be measured using X-ray line broadening techniques, it is first necessary to separate and concentrate this phase by electrolytic extraction. Extraction is necessary because the difference between matrix and precipitate lattice parameters is only approximately 0.5 pct and intensities of.the (y') phase lines are very weak relative to those of the matrix. The extraction techniques employed have been described before and found to produce a reasonably quantitative separation.398 A water solution of 15 pct H3Po4 is used at a current density of 0.5 amp per sq in. at 6 v. The precipitate particles are separated from the liquor by centrifuging and decanting and are then washed, dried and repowdered. A plot of the X-ray intensity vs diffraction angle for the (111) line of the precipitate particles was used as a measure of particle size. The intensity curve approximated the shape of Gaussian distribution function and its breadth was measured at the half height. The (220) line of a silicon standard was used to correct the measured line breadth for instrumental and other broadening errors. The Scherrer formula was used to calculate particle

Jan 1, 1961

In the Texas Panhandle 277 oil wells and 60 gas wells were completed during 1942, as compared with 647 oil and 52 gas wells completed in 1941. Fourteen dry holes were drilled in the Texas Panhandle in 1942, of which five were wildcats, resulting in four failures and one gas-field discovery in Sherman County; the latter being Hazy-Herrington-Marsh No. I Bivins completed for 5,600,000 cu. it. ol gas from 2989 to 3226 feet. During the year 1942 the Texas Panhandle produced, by counties, the following quantities of oil:

Jan 1, 1943

In the Texas Panhandle 277 oil wells and 60 gas wells were completed during 1942, as compared with 647 oil and 52 gas wells completed in 1941. Fourteen dry holes were drilled in the Texas Panhandle in 1942, of which five were wildcats, resulting in four failures and one gas-field discovery in Sherman County; the latter being Hazy-Herrington-Marsh No. I Bivins completed for 5,600,000 cu. it. ol gas from 2989 to 3226 feet. During the year 1942 the Texas Panhandle produced, by counties, the following quantities of oil:

Jan 1, 1943

US 4,190,436 - In the cyanide leaching of gold ore in tailing or ore dump piles, or gold ore in vats or on pads, the ore is agitated and oxygenated by introducing timed bursts of air, along with cyanide in a cyclic or regulated manner. The leach liquor is drained from the material by providing a continuous flow of air. Fines are homogenously mixed, thereby reducing channelling In the ore bed. Yield is improved and cyanide consumption lessened. R M. Hughes Feb. 26, 1980. 7 pp. (75-105). Filed. 12-20-77 (862,335).

Jan 1, 1982

By R. L. Sandefur

Professor Kim's excellent review article1 on ultimate pit planning contains a statement of the apparently widely held but incorrect belief that "kriging provides information on the confidence limits around the estimate which no other extension technique is capable of supplying." If a geostatistical approach is valid, there are several good reasons for using kriging but uniquely provided confidence limits is not among them. If kriging is possible, then confidence limits can be calculated for any other linear estimate.

Jan 6, 1979

By Burt C. Mariacher

Two AIME sponsored symposia to be held during the year 1970 will examine copper, lead and zinc metallurgy in considerable depth. MBD and the Extractive Metallurgy Division of The Metallurgical Society will participate in both. Thus, the full field of minerals and metals processing including milling, smelting, and refining will be covered. Since these symposia hold special interest to MBD members, it was felt that a useful purpose could be served by devoting this column to a description of what has been arranged for the registrants.

Jan 1, 1970

By W. N. Lacey, D. F. Botkin, B. H. Sage

JOULE-THOMSON coefficients for two natural gases were determined at pressures up to 600 lb. per sq. in. throughout the temperature interval between 70° and 310°F. From these primary data and available information relating to the isobaric heat capacities of the components at infinite volume, the heat capacities of these gases were computed throughout the above-mentioned range of pressures and temperatures. The enthalpies of the gases were computed as a function of state and the results compared with values obtained by several methods of prediction currently available. The results are presented in graphical and tabular form.

Jan 1, 1942

By David A. Wracher

A geologist may produce for himself a surprisingly accurate photo base map and stereo coverage at low cost without the use of expensive equipment and complex photogrammetry. If care is taken and the program well thought out, good results can be expected. The only equipment necessary in this method is a small format (small negative size) camera, a few rolls of film and the appropriate filters. A light aircraft, with an opening in the bottom, is preferable so that the pictures can be taken vertically and from inside - the aircraft. The method will produce high resolution prints at large scales in the range of 1: 1200 to 1:7200.

Jan 11, 1973

By R. C. Gifkins

The ideas expressed in this paper interest me very greatly, partly for their own sake and partly because they are very close to some speculation I have recently made concerning grain boundary diffusion. This is in a paper describing an extension to Mott's "island" theory of the grain boundary, to be published shortly.37 The facets or islands of good fit are identified in terms of specific crystallography, as in the model put forward by Brandon et al., and the bad fit between them is suggested to be interlinked "channels" of relaxed vacancies, associated with grain boundary ledges.

Jan 1, 1969

By Hemendra N. Kalia

A method is proposed for the preliminary design of coal mine openings and pillars using existing design formulas. The suggested method incorporates geophysical and core logging techniques, as well as the structural properties of the rock. Some of the existing design equations have been simplified and are included. It is anticipated that the additional cost of rock mechanics tests and logging work will be more than offset by the increased coal recovery that does not jeopardize the safety of miners,

Jan 1, 1977

By S. O. Reichert

The nuclear industry has made a considerable effort to reduce environmental pollution with the result that knowledge in the field of radioactive waste management is well advanced. An example of the methods used for radioactive waste disposal is provided by the Savannah River Plant (SRP) operated by E. I. du Pont de Nemours & Co. for the AEC. It occupies an area of 320 sq mi along the Savannah River downstream from Augusta Ga., and has production facilities that include a fuel preparation area, three reactor areas, two chemical separation areas (F and H), and a heavy water plant. Gaseous, Liquid and Solid Radioactive Wastes Are Handled During Disposal The primary sources of radioactive waste are the reactor and chemical separation facilities. The reactors are cooled and moderated by heavy water which, in turn, is cooled by river water in heat exchangers. This arrangement prevents irradiation of the river water so that radioactivity is not discharged into the river water except when small quantities of moderator are lost by heat exchanger leaks. Because of the high cost of heavy water, these losses must be kept to a minimum.

Jan 9, 1968

By Walter Scott

THE removal of lead by fire refining methods from copper of electrolytic quality is growing in importance. Particularly is this true of the refining of secondary copper and copper cathodes obtained from electrolytic cells where lead is used as the anode material, as in the electrolysis of ore-leaching solutions and foul electrolyte. When investigating the removal of small amounts of lead from molten copper in a reverberatory furnace during the refining of secondary copper of otherwise electrolytic copper quality,1 it was found necessary first to FIG. 1.-SAMPLING DEVICE. know something about the distribution of the lead throughout the bath. The authors believe that it is not generally known how small amounts of lead as an impurity are distributed in a molten copper bath; that is, whether the lead is concentrated at the bottom or at the top, or whether it occurs more or less uniformly throughout the bath. The data contained in this report may help, therefore, in the development of a satis-factory fire refining method for the removal of this obstinate element from a molten copper bath.

Jan 1, 1930

By V. R. Garfias, R. V. Whetsel, J. W. Ristori

Preliminary estimates indicate that world consumption of petroleum and related fuels in 1938 will be close to 1,908,000,000 bbl., or approximately 7,000,000 bbl. less than in 1937. This total does not include military consumption in foreign countries, which for obvious reasons is not made public. Foreign military consumption in any one year, however, is approximately represented by the difference between the total production of petroleum and related fuels and the "partial total" consumption above noted, after adding any decrease, or subtracting any increase in stocks in the United States. Fig. 1 illustrates this "difference" and shows that in 1937 and 1938, owing to the wars in China and Spain and the possibility of armed conflict in Central Europe, foreign military consumption—and possibly additions to foreign stocks—increased nearly 70,000,000 bbl. in 1937 over 1936 and remained at this high rate throughout 1938. No official information on foreign oil stocks is available to the writers. Table 1, recently published, purports to give the oil in storage in some of the European countries, but it is not known whether the figures include oil stocks for military purposes. It should be noted that with the annexation by Germany of Austria and part of Czechoslovakia the consumption of the country has increased to 53,000,000 bbl., which is about 36,000,000 short of the German produc-

Jan 1, 1939

By J. W. Ristori, R. V. Whetsel, V. R. Garfias

Preliminary estimates indicate that world consumption of petroleum and related fuels in 1938 will be close to 1,908,000,000 bbl., or approximately 7,000,000 bbl. less than in 1937. This total does not include military consumption in foreign countries, which for obvious reasons is not made public. Foreign military consumption in any one year, however, is approximately represented by the difference between the total production of petroleum and related fuels and the "partial total" consumption above noted, after adding any decrease, or subtracting any increase in stocks in the United States. Fig. 1 illustrates this "difference" and shows that in 1937 and 1938, owing to the wars in China and Spain and the possibility of armed conflict in Central Europe, foreign military consumption—and possibly additions to foreign stocks—increased nearly 70,000,000 bbl. in 1937 over 1936 and remained at this high rate throughout 1938. No official information on foreign oil stocks is available to the writers. Table 1, recently published, purports to give the oil in storage in some of the European countries, but it is not known whether the figures include oil stocks for military purposes. It should be noted that with the annexation by Germany of Austria and part of Czechoslovakia the consumption of the country has increased to 53,000,000 bbl., which is about 36,000,000 short of the German produc-

Jan 1, 1939

By Chingyuan Y. Li, C. Y. Hsieh

Realizing that aluminum will have a great role to play in the coming industrialization of China, Chinese geologists have long been looking about for some aluminum deposits. The possible sources appear to be alunite, the alumina-rich shales, and the bauxite deposits. The locations of deposits are shown in Fig. I. Alunite Our attention was first directed to the alunite deposits along the southeastern coast of China. Table I summarizes the reserves now believed to exist in that region. Other alunite deposits have been found in Kiangpei, Szechuan province; Charming. Liuyang and Hsanshan, Hunnan province Tsingchow and Chowyuan, Shantung province. No reserve figures are available. High-alumina Shale Shale high enough in aluminum to serve as a source of that metal has been found in northeastern China(Tab1e 2). In Manchuria, the Manchuria Light Metals Co., at Antung and Fushun, operating under Japanese control, has been the only active producer of aluminum. It is not known, however, whether the company uses local raw materials or imports ore from elsewhere.* Shantung Bauxite Bauxite was first recognized in China at Paoshan, Shantung province. Although the reserve is reported to be large (estimated at 271 million tons), the high content of insoluble residue (SiO2) and mineral composition (diaspore) are dis-

Jan 1, 1948