Search Documents

By A. M. Hanna

This paper presents the experimental investigation on the ultimate skin friction of batter piles. The model piles were pushed in medium dense sand deposits at different inclinations up to 30 with respect to the vertical and tested under axial compression loads. The decrease in the total skin resistance with increasing pile inclination can be explained in terms of the reduction of the ave­rage mobilized angle of friction between the pile shaft and sand. The analysis, which takes into account asymmetrical earth pressure distributions around the pile shaft, showed good agreement with experimental results.

Jan 1, 2010

By E. Mongilardi

The construction of large underground openings through cohesionless or weak cohesive soils and under the water table in particular, often requires a ground improvement to be done from the surface or ahead of the excavation face in tunnelling problems. To this purpose various injection procedures have been used in the past and new outstanding techniques have been developed recently, such as "jet-grouting", extending the feasibility range. The paper presents a review of basic principles and practical design criteria with particular reference to the newest trends of development. Case histories have been selected within the experience of specialist contractor Rodio Co. showing the variety of problems solved by manifold grouting procedures and layouts, in widely different soils ranging from the sandy-gravelly alluvia of Milan to the soft marine clays of Singapore.

Jan 1, 2010

A consideration of mining ventures and the changes of an environmental nature that occur. The paper is introduced with a general statement claiming recognition that mining ventures are important to human well-being but that these need to be justified against the environmental changes that they bring about. The various factors that need to be considered are cited followed by an historical review of mining activities. The various environmental issues are discussed under three headings; socio-economic, physical and biological, prior to reviewing the world's demand for minerals including fossil fuels. In conclusion guidelines for appraising mining ventures relative to environmental changes that may occur, are given.

Jan 1, 1981

Gold mines produce unique water treatment requirements. This paper focuses on case studies of innovative processes used for treatment of water resulting from gold mining and processing. The case studies include treatment of mine dewatering water for beneficial application from an Australian gold mine, Bendigo Mining, as well as treatment for arsenic removal of tailings water from mining and processing at Goldcorp mines in Canada. Gold mining can often require dewatering to prevent groundwater seeping into and flooding the mine workings. Gold mining and processing often accumulate wastewaters in a tailings dam. The mine water can contain contaminants such as dissolved salts, iron, arsenic, manganese, heavy metals and odorous sulfates. Environmental discharge requirements as well as community needs for water drive mine operators to consider the most appropriate water treatment process. Treatment of gold mine water can require processes including oxidation, pH adjustment, coagulation, flocculation, clarification, further oxidation/adsorption of specific metals such as manganese, filtration, salt reduction utilising reverse osmosis, brine minimisation and other innovative technologies. These processes are discussed through the case studies with examination of the specific treatment process that is required. This paper uses real case studies of gold water treatment processes to explain and examine the technology and the reasons for designing specific processes. The focus is toward explaining innovative processes where the water is used for sustainable environmental discharge or treatment to a quality that can be beneficially used by the local community.

Jan 1, 2007

By D. L. Pitt

This paper, describing the milling methods at the concentrator of the Premier Gold Mining Co., Ltd., Premier, B. C., Canada, is one of a series being prepared by the United States Bureau of Mines on milling methods and costs in the various mining districts throughout the United States and Canada. ACKNOWLEDGMENTS The authors wish to acknowledge the assistance and suggestions given during the preparation of this paper by the engineering staff and accounting department of the Premier Gold Mining Co., Ltd., all of whom have assisted materially in gathering the data used.

Jan 1, 1933

By Douglas D. Campbell, Alan S. Imrie

INTRODUCTION Mica Dam is located on the Columbia River just downstream of the "big bend" of the Columbia, where it leaves the Rocky Mountain Trench and begins to flow southwards, approximately 85 miles north of Revelstoke, B.C. (Fig.l). The dam was built as one of three Columbia River Treaty dams in British Columbia which regulate the flow of the river and provide flood control downstream in Washington and Oregon. In addition, the three Canadian dams make possible greatly increased power generation at existing power plants in the United States and further development along the Columbia and its tributaries in British Columbia. History Mica Dam, constructed during the period 1967 to 1973, is a zoned earthfill embankment 650 feet high, which has 12,000,000 acre feet of live storage and an available head of 550 feet. Power intakes which would serve either a six-unit surface or underground plant were incorporated into the design and construction of the right abutment of the dam (Fig. 2). Prior to 1971 alternative 2500 MW capacity surface and underground powerplant arrangements were studied. Cost estimates for the two alternatives were the same within the limits of estimating procedures. However, it was believed there was a certain continuing risk in locating a surface plant at the toe of a steep canyon wall. Therefore, in 1971 a tentative decision was made to proceed with an underground plant, provided that additional exploration confirmed assumptions of

Jan 1, 1976

By Eric Bain Wasmund, Lance Christodoulou, Julio Jairo Carmona Franco, María Fernanda Castillo, Jose Concha

"A number of technologies are in practice for selectively removing coarse gold from conventional grinding circuits. These circuits are often designed so that the grinding mill output is size classified, with large (or high density) particles being removed before the tails are returned to the mill. Because of the high relative SG of gold, and the fact that some forms of gold such as free gold do not break apart during conventional grinding, coarse gold can accumulate in the circulating load, and eventually be lost.Eriez has developed a flotation cell that uses fluidized water to enhance flotation of coarse particles. More than 40 units have been sold in industrial minerals, and we are now exploring applications for the HydroFloat® in the gold industry.Mineros S.A currently produces approximately 120,000 oz of gold per year by gravity concentrating alluvial gold ore with a mean particle size of 330 microns, followed by further concentration using a Falcon separator. A 400 mm diameter pilot-scale HydroFloat® was added to the tails of the Falcon to test whether additional gold could be captured. Enrichments of 50-600 times and recoveries normally in excess of 95% were achieved. This allowed direct smelting of the gold concentrate. Metallurgical results and operating parameters such as water addition and power will be discussed during the presentation.This result opens the possibility that the HydroFloat® could be used directly in the grinding circuit, for removing coarse gold in the circulating load. This work also shows the possibility that the HydroFloat® can produce a throwaway tail, which will reduce the size of the circulating load stream and the grinding requirements of the circuit."

Jan 1, 2015

By G Mark, K L. Blake, G de Jong, J F. Rotherham, N D. Adshead

Magnetite deposits with distinctive ¦ actinolite ¦ apatite-bearing gangue and spatially-extensive sodic-calcic wall rock alteration occur in both Proterozoic metamorphic terrains and Mesozoic-Tertiary magmatic arcs. Examples from both settings constitute significant sources of iron ore (egKiruna, Sweden; El Romeral, Chile) and some host major Cu-Au deposits that have a local association with K-silicate alteration (eg Cloncurry district, NW Queensland; Copiapo district, Chile). A growing body of evidence points to a hydrothermal origin for these systems involving high temperature, low S oxidised fluids. The Cloncurry magnetite-Cu-Au deposits are products of the local structurally channelised influx of a specialised high salinity ore fluid into larger-scale alteration systems developed during pluton emplacement at greater depths than those associated with subvolcanic (porphyry) Cu-Au deposits. The geological characteristics of deposits in magmatic arcs are consistent with a similar mode of origin albeit in rather different tectonic settings.

Jan 1, 1995

By Edwin F. Shorey, Richard F. Coon, Steven B. Fradkin

Crosstown Interceptor Phase IA is the first deep tunnel element of the Milwaukee Inline Project. The tunnel contract includes 6,492 meters (m) of 9.1-m-diameter tunnel, two access shafts, and partial lining for structural purposes. The work also includes grouting to be performed as directed by the engineer to provide groundwater infiltration control in lined and unlined reaches of the tunnel. This paper summarizes infiltration observations, progress of the grouting work, and its potential application to the remainder of the Milwaukee project.

Jan 1, 1987

By Daniel Briones

El presente trabajo señala las bases que fundamentan la aplicación de los Sistemas de Gestión Integrados y se ofrecen argumentos que sustentan los mecanismos usados para integrar los sistemas de Seguridad (NOSA), medio ambiente (ISO 14001) y calidad (ISO 9001); y la necesidad de su uso como herramienta de gestión por parte de la organización, llegando a todos los niveles hasta alcanzar la madurez del Sistema. Asímismo, se describen algunos ejemplos del impacto positivo, que ha significado la implementación de este Sistema en la unidad de producción Uchucchacua (cuarta productora mundial de Plata,), desde el inicio del Proyecto, hasta lograr la revalidación de la Certificación de las normas ISO 14001, y la cercana certificación en OHSAS 18001 e ISO 9001.

Sep 12, 2005

By A. G. Doll

"Many power-based grinding models exist, and most operators are familiar with Fred Bond's ""third theory"". Bond's model is most commonly used to describe primary and secondary grinding to product sizes above, for example, 100 µm. Operators sometimes use Bond's equation to describe grinding in situations where it is not appropriate, such as fine grinding below 50 µm. Using an alternative model would be a better choice in this situation.Bond's equation is one in a large family of models. Related equations better suited to fine grinding include the “signature plot”, Von Rittinger's model and Charles' equation. These models have a similar form to Bond's and can be fit to industrial regrind mills and laboratory tests using the simple regression tools in the charts of computer spreadsheets. Operators will find that fine grinding calculations are both easier and more accurate when using the alternative equations to fit their regrind milling surveys or when performing laboratory regrind mill scale-up for plant design.None of these models are new: Charles' equation was published in 1957 and Von Rittinger's model was proposed in 1867. A quick refresh how to apply these equations can turn these oddities from the undergraduate curriculum into useful tools for plant optimization. They can be fit to any type of mill including stirred and tumbling ball mills.IntroductionBuilding a case for fine grind modelling requires reviewing some theory before building a framework for doing fine grinding calculations. The actual calculation procedure recommended is easy and can be applied by plant metallurgists. Don’t be frightened by the theory; the end result is reasonably simple.The observation that mineral breakage is related to the absorption of energy is usually attributed to Von Rittinger (1867). Lynch and Rowland (2005) describe that the ability to empirical test and calibrate energy models of breakage didn’t exist until the widespread adoption of electric motors in the mining industry during the 1930’s and 1949’s. A series of technical papers published by the Allis Chalmers company during the 1940’s demonstrate that they were attempting to do such a calibration using Von Rittinger’s model which is usually stated as: “the energy consumed in the size reduction is proportional to the area of new surface produced.”"

Jan 1, 2017

By B. T. Lusk, Q. Q. Huang, R. Q. Honaker, K. A. Perry

Rock dust is applied in underground coal mines to prevent the propagation of coal dust explosions. It is applied either dry or wet. Both methods have advantages and disadvantages, but the formation of caked rock dust particles is cited as a significant concern for wet applications. We conducted a study to evaluate the effect of modifying the rock dust particle surfaces to repel water and each other by the addition of oleic acid and sodium oleate. At a sodium oleate dosage of 1 kg/t, a contact angle of 112o was measured, indicating strong surface hydrophobicity and thus the ability to repel water. Fourier transform infrared spectroscopy (FTIR) studies indicated a chemisorption mechanism, which is necessary for long-term stability of the surface modification. The dispersibility of the modified rock dust samples was elevated by the application of both oleic acid and sodium oleate, thereby indicating a significant reduction or elimination of the detrimental effect of caking. Tests in an explosion chamber showed an 82.8 percent reduction in the dust explosion potential relative to untreated rock test applied by the wet technique.

Jan 1, 2015

By Mehmet Bugdayci, Onuralp Yücel, Yeliz Demiray Cucurachi, Ahmet Turan

The production of strontium (Sr) metal from its oxide via an aluminothermic process under 1–5 mbar pressure was examined in this study. SrO of 99%purity by weight was used in the experiments. The effects of stoichiometry and the duration of the process on the efficiency ratio of the metallic strontium were examined. The effects of functional additives (BaO, CaO, CaC2) were also examined. Characterization was carried out using X-ray diffraction spectrometry (XRD), atomic absorption spectrometry (AAS) and flame photometry techniques. The highest Sr efficiency ratio obtained was 96.89% in the experiment conducted at 1250 °C with 300% Al stoichiometry and 300% BaO stoichiometry.

Aug 7, 2020

By Y. G. Li

The design and construction of the hand-dug caisson pier foundation of the Shenzhen International Trade Centre are described in the paper. In addition discussions and inquires about the load-bearing capacity of the hard bedrock are offered.

Jan 1, 2010

Baja Mining is currently constructing the Boleo metallurgical plant in Santa Rosalia, Mexico to recover copper, cobalt, zinc and possibly manganese products from the Boleo ore. The process involves an acid seawater leach of the whole ore followed by solid-liquid separation and washing of the leach residue. Solvent extraction is used to separate copper, cobalt and zinc from solution. Copper and cobalt are recovered as cathode metal products and zinc as a zinc sulphate monohydrate. Manganese may be directly precipitated as manganese carbonate which can be used as a feedstock for manganese metal production. Laboratory testing has continued to refine various aspects of the process including iron removal, cobalt and zinc solvent extraction, cadmium cementation, cobalt electrowinning and manganese metal electrowinning. The results of this testing are reported in this paper.

Jan 1, 2012

By W. Petruk, M. J. Matos

An aplite ore from Guarda in northern Portugal, containing albite, microcline and quartz and muscovite gangue was studied to identify conditions for extracting the feldspar minerals. The large amounts of quantitative mineralogical data needed to evaluate grinding behaviour were provided by automated image analysis. The images were acquired on polished surfaces by measuring back-scattered electron signals produced with a microprobe. Minerals were identified from X-ray spectra and discriminated by grey level and element-characteristic X-rays. The quantities and size distributions of the minerals were determined by measuring thin sections of unbroken ore to predict the grind required to liberate the feldspars. The ore was then ground to -1.7 mm, polished sections were prepared from sieved fractions and the quantities of mineral species and apparent total liberation were determined by analysis. The predicted and measured liberations were compared and the grinding behaviour of the ore interpreted. In an appended correction, the correct version of Equation 1 is represented and Tables 3 and 6 are revised to consider all size fractions, including those coarser than 300 micrometres, in calculating the total liberation from King's fractional liberation

Jun 18, 1905

By R. M. Santmyers

Thorium and cerium are two of the group of elements known as "rare earth metals," and are obtained from the mineral monazite. Previous to the employment of thorium and cerium in incandescent gas mantles these elements were nothing more than laboratory curiosities, as the rest of the rare-earth metals are to-day. The most important salts of these rare earths are the nitrates. In the manufacture of gas mantles, thorium nitrate is the principal ingredient and forms prom 92 to 99 per cent of the impregnating material; the other 1 or 2 per cent is largely cerium nitrate and is quite as necessary, for without it there would be little luminosity to the mantle when in use. When the mantle is "burned off," the nitrates are changed to oxides. The monazite used as a source of thoria contains from 6 to 9 per cent of thorium oxide (Th02) and 24 to 32 per cent of cerium oxide (Ce203). As only the thoria and a very small hart of the ceria from the monazite could be used in gas-mantle manufacture, for a time the residues consisting mostly of ceria with somewhat smaller quantities of other rare earths found no commercial application. Later, however, they came to be utilized in several ways, the most important being: (1) the manufacture of cored flaming arc carbons, a great, irmprovement over the plain arc carbons used in electric lighting; (2) cerium metal used in the manufacture of pyrophoric or sparking alloys or "flints" for automatic pocket lighters and miners' lamps; and (3) the production of special kinds of optical and art glass.

Jan 1, 1930

By J. C. Vreugdenburg, B. A. Dippenaar, J. Muller, T. L. de Vries

Iron ore fines are agglomerated to produce sinter, which is an important feed material for blast furnaces worldwide. A model of the iron ore sintering process has been developed with the objective of being representative of the sinter pot test, the standard laboratory process in which the behaviour of specific sinter feed mixtures is evaluated. The model aims to predict sinter quality, including chemical quality and physical strength, as well as key sinter process performance parameters such as production rate and fuel consumption rate. The model uses the finite difference method (FDM) to solve heat and mass distributions within the sinter pot over the height and time dimensions. This model can further be used for establishing empirical relationships between modelled parameters and measured sinter properties. Inputs into the model include the feed material physical properties, chemical compositions, and boundary conditions. Submodels describe relationships between applied pressure differential and gas flow rate through the bed of granulated fine ore particles, combustion of carbonaceous material, calcination of fluxes, evaporation and condensation of water, and melting and solidification. The model was applied to typical sinter test conditions to illustrate the results predicted, and to test sensitivities to parameters such as feed void fraction, feed coke percentage, and the fraction of combustion heat transferred to the gas phase. A model validation and improvement study should follow, ensuring sinter test results are free from experimental errors by conducting repeated tests.

Jan 1, 2015

By Byron M. Bird, Earl R. McMillan

"The method and apparatus described herein was developed at the Northwest experiment station of the Bureau of Mines, Interior Department, in cooperative research work with the University of Washington. A fuller description will appear in a bulletin entitled ""study of coal washing problems in the Pacific Northwest, to be published by the University. During the past four years this Bureau and the University have been co-operating with various coal companies in the Pacific Northwest in an extensive study of coal washing problems. Much of the valuable data resulting from this study has been obtained with the well-known float-and-sink test. This test has known for a number of years****, but its possibilities have not been thoroughly understood. A few investigations have developed apparatus and technique suitable to their needs, but these were not adopted to the conditions faced in the Northwest. Thus, the necessity arose for designing suitably equipment and working out a method of procedure or technique in carrying on the fundamental studies of coal washing by means of the float-and-sink test method."

Feb 1, 1924

By K. G. Markkola

Since 2005, Compafifa Contractual Minera Candelaria (CCMC) has defined various strategies which aim to optimize the usage of the available energy in each of the SAG grinding circuit modules (SABC-A configuration). For this purpose, the use of larger size balls along with operating with an optimum balls/load ratio has been implemented. Additionally, in the ball mills, the amount of balls in relation to the equipment's usable diameter has been optimized. In the pebble crushing circuit, the percentage of material passing 12 mm (112 in) product has been increased by 15% by: (1) modifying the crusher mantle profile, (2) implementing a strategy for maximizing the power in each crusher, (3) using continuous improvement tools (Lean - Six Sigma), (4) redesigning SAG mills discharge grates, and (5) changing discharge grates in order to control the crusher feed size distribution profile. All these activities have improved plant throughput by 1,000 t/d with no significant capital investment. As part of the energy consumption optimization study, we have considered determining the optimum operational rate of each SAG mill, in relation to the mill liner life and also the improving the control strategy in conventional grinding.

Jan 1, 2007