Search Documents

By F. J. Fayers, R. L. Perrine

For many years the problem of increasing ultimate recovery of oil from a reservoir has been a subject of interest to the oil industry. At present, a standard secondary recovery technique is to flood the reservoir with water once natural forces of the system are depleted. The permeability characteristics of the rock, together with interfacial forces which exist between the two fluids and the porous material. allow only part of the oil in the rock formation to be recovered by the water-flooding process. Laboratory experiments have shown that when detergents are added to the flooding water, the flow properties of oil in a porous rock arc improved. This improvement results in greater oil recovery. Even though higher recoveries are obtained using detergents, the extra cost associated with the method may make it economically unsatisfactory. To establish economic feasibility requires experimental laboratory measurement of fluid and rock properties together with a calculational procedure to predict field results. Pilot tests in the field may also be required. This paper presents a mathematical procedure for predicting detergent flood behavior. A number of reasonable simplifying assumptions are made to obtain a tractable system of equations. The resulting method may be regarded as a generalization of Buckley-Lev-crett' theory to solve simultaneously for water saturation and detergent concentration profiles. Consequently this type of calculation can be used in much the same manner as Buckley-Leverett theory is used to evaluate a water flood. The mathematical method employed is the so-called method of characteristics for solving hyperbolic partial differential equations. This application of the method is instructive because several other problems in reservoir analysis may be analyzed in a similar manner. FLUID FLOW EQUATIONS The flow behavior of oil and water without detergent through porous reservoir rock is usually expressed by Darcy's law and a continuity equation for each phase. If gravitational forces are neglected, vrg = kr (s)µr v p rg.........(1) vrg = kr (s)µr v p rg.........(1) ? pa va = F ?/?t (sd) where v is the volumetric flux, k represents permeability, S is saturation, and P the pressure. Fluid viscosity is denoted by 11, p is the density, 4 is porosity, and I the time. The subscripts w and o refer to water and oil. The capillary forces in the system lead to a difference in pressure between phases. This may be expressed by the relation: Pm -P0 =Pc(S).........(5) The capillary pressure? P,, is determined experimentally as a function of saturation. DETERGENT BALANCE EQUATION Addition of detergent to the water phase affects the flow properties of the system. Capillary pressure and relative permeability become functions of detergent concentration, c, as well as fluid saturation. That is: P--P (S,c) and k,,,.- - -- k,,,. At low oil saturation values, the presence of detergent reduces capillary pressure and reduces the relative permeability ratio. Detergents are surface-active and adsorb on rock surfaces. The quantity adsorbed, a, will depend on the concentration c of detergent solution and may also depend on the saturation; thus, a = a(S,c). In this analysis we have assumed that the detergents used are water soluble but not oil soluble, and their movement is therefore restricted to the water phase. The dispersion of detergent in water is neglected by comparison with transfer by flow within the system. Detergent movement is determined by the water flux and adsorption: ? cv m = -F ?/?t (cs + a) We will assume that the quantity of detergent in solution is too small to significantly change water density or viscosity. When the permeability and capillary pres-

Anglo American Platinum practices fine grinding in its processing plants to enhance the liberation of valuable minerals. If the fine particles of valuable minerals generated during fine grinding are not recovered during the flotation process, this could significantly contribute to the overall losses. This study examines the flotability of fine moncheite (PGE mineral) particles in a controlled environment (moncheite size distribution, concentration and liberation). A barren Norite ore ground to 40% and 80% passing 53µm was spiked, with four different size fractions of moncheite (-5, -10+5, -25+10 and -53+25µm) in order to evaluate the effect of particle size on flotation. The investigation also included the effect of energy input and collector dosage on the flotation of two moncheite size fractions, namely -5µm and -10+5µm. The results showed that the moncheite particle size has a significant impact on flotation. Coarse particles (-53+25µm) showed the highest Pt flotation kinetics and overall recoveries. The -5µm size fraction of moncheite could also be recovered by flotation, however, at a lower rate compared to the other size classes investigated. The increased collector dosage of 300g/t at the finer Norite grind of 80% passing 53µm enhanced the flotation rate of the -5µm size fraction of moncheite when compared to the lower collector dosage of 150g/t. The higher energy input during laboratory flotation, at an impeller speed of 1000rpm also increased the flotation rate of the -5µm size range, however, at a lower concentrate grade, when compared to the lower impeller speed of 700rpm. More favourable Pt flotation kinetics data was obtained for the -53 +25µm size fraction of moncheite at the fine Norite grind when compared to the coarse Norite grind. Keywords: flotation, moncheite, particle size, energy input and SIBX

Sep 1, 2012

By Michael H. Wysockey

The load test program for the pile foundation at Soldier Field included static and dynamic load tests at four locations around the site. The dynamic tests were run with no knowledge of the static results, and comparison between the two is very good. It was necessary to use a special testing hammer (not the production hammer) to demonstrate capacity with dynamic testing. Over 90% of the piles were HP14x89 with a design load of 230 tons (18 ksi). The load tests showed a capacity in excess of 590 tons for all tests where sufficient set up time was allowed. The remainder of the piles were mostly HP 12x53 with a design load of 100 tons (13 ksi). The measured capacity of these piles was typically about 250 tons. One experimental HP12×74 pile with a nominal yield of 65 ksi held 730 tons (67 ksi) before failing.

Jan 1, 2002

By Carl J. McHargue

Mechanical twins were produced in electron-beam melted columbium by high-speed impact at room temperature and by slow or fast compression at -196°C. The composition plane of the twins was { 112} and the shear direction was <111>. Notches in the twin bands often corresponded to traces of {110) of the matrix and appeared to be untwinned regions. Markings within the twin bands were interpreted as resulting from {110} slip in the twins. THERE has been much work in recent years concerning plastic deformation by glide, and the dislocation theory relating to glide has reached a relatively high degree of development. On the other hand, there have been fewer studies of deformation by mechanical twinning, and understanding of this process is far from satisfactory. This method of deformation is of interest for at least two reasons. First, it provides a mechanism in addition to glide for the relief of stresses, and, in the bcc and hexagonal close-packed metals may result in significant amounts of plastic flow. Secondly, there is the possibility that twins may act as barriers for dislocation movement, resulting in pile-ups which could nucleate cracks. As might be expected, the bulk of the literature on mechanical twinning in the bcc metals is concerned with iron. A good summary of the work done prior to 1954 is contained in the book by all.&apos; Recently the refractory bcc metals have become increasingly important. Limited studies have shown that tantalum,2,3 molybdenum,4,5 vanadium,6,7 tungsten,&apos; and columbium9-11 deform by mechanical twinning under some conditions. Alloys of molybdenum with rhenium and tungsten with rhenium show extensive deformation by twinning at room temperature.I2-l4 Most of these studies have dealt primarily with mechanical properties at low temperatures or have shown the existence of twins, and there is only a small amount of information concerning the conditions under which they form. The subject of the present paper is the formation of twins under stress in columbium with a consideration of their morphology. EXPERIMENTAL PROCEDURE The material used for these studies was taken from an ingot of columbium which had been melted twice by the electron-be am-method. The analysis of the ingot was (in ppm): B < 1, C = 10, Fe < 100, The cast ingot contained very large grains, and it was possible to obtain single-crystal prisms which measured from ¼ to 3/4 in. on a side. A few experiments were conducted on polycrystalline plate which was prepared by rolling material from the same ingot at room temperature and annealing at 1000 in a dynamic vacuum of 10-6 mm Hg. This gave a plate in which the grains had an average diameter of 3 mm. After the specimens were cut from the ingot, the six faces were metallographically polished and elec-tropolished to remove all traces of cold work. Most of the observations were made on the surfaces of the deformed specirllens without further treatment. Occasionally, etching after deformation was desirable. In these cases, an etchant of the composition 50 parts H2O, 5 parts HNO3 25 parts HF, and 10 parts H2SO4 was found to delineate the twins very well. Unless considerable care was taken to ensure the removal of all disturbed metal left by the mechanical polishing, etching failed to reveal many of the features discussed in this; paper. The specimen&apos;s were deformed either by impact or slow compression at 77°K (liquid-nitrogen coolant), 198°K (dry ice and acetone coolant), and 298°K. The impact load was delivered by a hammer except in one case where the load was delivered by a bullet. Slow compression was carried out on a hydraulic testing machine equipped with a chamber to hold the coolant. EXPERIMENTAL RESULTS It has been generally believed that the conditions favoring the formation of deformation twins are large grains, low temperature, and impact loading. In fact, Barrett and Bakish2 found twins in tantalum only after impact deformation at 77°K, and Adams, Roberts, and Smallman10 observed twins in columbium only at 20 For these reasons, the initial experiments of this study used impact loading. Hammer blows caused many bands resembling twins in single crystals a.t 77" but not at 198°K. Only a few slip lines were observed on any of the single-crystal specimens of this study—essentially all the deformation occurred by twinning. The appearance of the twins on the as-deformed surface is shown in Fig. 1. Although both Figs. 1(a) and l(b) are photomicrographs of twins taken at the same magnification and from the same crystal, they are startlingly different in appearance. Fig. 1(a) was taken from the crystal face approximately perpendicular to the shear direction, whereas Fig. 1(b) was taken from

Jan 1, 1962

By Y. Fukunaka, M. Niinae, E. Kusaka, T. Kuzuya, R. Ishii

"Samarium oxalattr particles was precipitated in oxalic acid aqueous solution from samarium-loaded D2EHPA solution emulsified with a conventional impeller. The calculated fractional precipitation of samarium oxalate was reasonably compared with the value determined by chemical analysis. Morphological variation of oxalate precipitate particles was then examined with H2C2O4 concentration in aqueous solution, Sm(III) and D2EHPA concentrations in organic phase. The needle-like precipitate was identified as Sm2(C2O4)3 10H2O by XRD. Precipitates obtained at higher H2C2O4· or Sm(III) concentration greatly decreased the length of major axis of precipitate, while those at higher D2EHPA concentration increased it. The oxalate was further precipitated under ultrasonic irradiation. However, the morphological variation caused by theses processing variables was not so evident under ultrasonic irradiation as in an impeller or shaking mixer.IntroductionThe materials processing of the rare earth elements must be reviewed from the scope of industrial ecology, since they have the potential applications of magnetic materials as well as secondary battery in developing programs of the electric vehicle. The technological trend to develop the electric vehicle may greatly influence the concept of materials processing, since the global· environmental problem must accommodate with the sustainable development for mankind. The recycle design must be a key issue in the materials science and engineering.Solvent extraction provides a unique separation technology -in this sense. Doyle (1)(2) reported the integrating solvent extraction with processing of advanced ceramic materials, whose chemical composition and microstructure must be precisely controlled. In her paper, the higher productivity inherent to the present process superior to hydrolyzing metal alkoxides was emphasized. Oxalic acid has been used as precipitant for rare earth purification process, since rare earth oxalate has a very small solubility in water and can be easily decomposed to oxide. It is thus suitable for precipitation stripping agent in cationic exchange type extracting system (i.e. D2EHPA, VA-10, PC-88A and so on)."

Jan 1, 2000

By E Widzyk-Capehart, T Bednarz, O Daud, N Cutmore

The interest of industry, in particular future mining, is pointing towards the use of novel visualisation systems to improve the operational efficiency of user interfaces. While the technologies used to enhance operators’ experience are advancing, the implementation of novel visualisation paradigms within mining operations is trailing behind other industries, particularly health and aviation. In this work, we present a number of initiatives and use cases of immersive virtual and augmented reality systems that can fit within the mining context. These ideas represent a step towards new platforms that might increase the efficiency and safety of mining operations through applications such as 3D panoramic video monitoring technology with annotated information coming from big data analytics and visual analytics processing engines. However, while the technologies are used in a variety of training settings, their application in the working environment is lagging behind. This paper presents examples of scientific visualisations that could be applied in a mining context to extend the possibilities of operators’ cognitive abilities and working efficiency. They are intended to foster a discussion within the mining community to move beyond the training realm and into the operational environment.CITATION:Bednarz, T, Widzyk-Capehart, E, Daud, O and Cutmore, N, 2015. Effective immersive visualisation systems for mining applications and beyond, in Proceedings Third International Future Mining Conference, pp 31–36 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

This paper describes the excavation of No. 1 Power Station Lift Shaft at the Kiewa Hydro-Electric Project. The advantages and limitations of the borehole method are outlined, and general principles of plant design are discussed.INTRODUCTIONFor many years, attempts have been made to reduce mine development costs by various methods. Some of the, techniques of tunnelling have been adopted in horizontal headings, and in main vertical shafts, mechanical plant has displaced hand labour with notable success. However, in the field of small rises and winzes, improvements have largely been effected by attention to details of procedure. The most promising avenues for&apos; substantial reductions in cost relate to:(a) Long-hole drilling(b) The borehole method(c) Calyx drilling.Whilst each of these methods has its peculiar advantages, the borehole rising method is probably most useful, and capable of wide application.In brief, the borehole method of rising requires a, drill hole parallel to the axis of the rise. A hoisting rope is passed through the borehole, and is attached to a platform on which the rising crew are raised with their equipment to the drilling position in the rise.When properly planned, the method is particularly safe, and has generally received the approval of mine inspectors and safety authorities. Rising work is generally hazardous, even when special timbering methods are used. In...

Jan 1, 1959

By Paul Staples, Paul Messenger, Greg Lane

"Every project is different. While “conventional” SAG and ball mill circuits will suit many projects, for others there are alternatives, which may produce improved outcomes. This paper examines particular examples of recent front end designs which either went against conventional thinking or which employed “out of the box” thinking to realize the desired results.One such example is the design strategy employed for a small capacity gold plant in Victoria, Australia. The selection of HPGR technology for small capacity projects is not generally favoured, given the relatively high cost of small HPGR machines. However, the unusual size distribution of the gold and its liberation characteristics were expected to lead to improved gold recovery offsetting the higher capital cost.Another example is the first large scale application of milling in acid for copper recovery, at a project in south east Asia. The stainless steel, single stage SAG mill using ceramic grinding media was more expensive than a mill constructed of conventional materials. However, the steps of scrubbing, slurrying, grinding and leaching could all be achieved in a single unit operation and the need for thickening and repulping with acid after milling was eliminated.Rod mills were selected for both primary and secondary milling duties for another south east Asian project despite their somewhat outdated reputation. A review of previous industry experience confirmed that rod mills could outperform conventional rod/ball or SAG/ball circuits in cases where the size distribution of the ground product is critical to downstream recovery.These examples are discussed with particular focus on the key drivers in each case."

Jan 1, 2008

By M I. Pownceby, N A. S Webster, R Pattel, N Ware

The decrease in quality of Australian iron ore, coupled with the demand for more efficient energy use, necessitates closer monitoring and optimisation of process conditions for iron ore sinter production. Sinter properties are correlated with the mineralogical content and traditionally, quality control has relied on methods such as Fe2+ determination, point counting via optical microscopy and automated electron beam techniques such as QEMSCAN; these can have a typical turnaround time of several days between sampling and reporting of results. As well, there is additional uncertainty around quantifying some of the complex mineralogical phases in sinter such as silico-ferrite of calcium and aluminium (SFCA) and SFCA-I, which are key phases influencing sinter quality. There is a clear need for the implementation of alternative analytical methodologies that offer a turnaround in hours or even minutes to provide information to accurately maintain production conditions.X-ray diffraction (XRD) is a technique widely used for the quantitative mineralogical phase analysis (QPA) of ores and processed materials in the iron ore industry. Partial least squares regression (PLSR) analysis methods have recently been suggested as an indicator of sinter Fe2+ content from powder XRD data without the need for rigorous and often time-consuming mineralogical analysis by the operator. In this study we provide results from the implementation of PLSR to predict the strength of iron ore sinter. Results are sourced from a well-constrained data set comprising strength properties (as quantified by a tumble index (TI)) from a series of compact laboratory test samples. Using this data set it was determined that PLSR has potential to be used as a method for calculation of sinter TI from powder XRD data and, therefore, process control.CITATION:Webster, N A S, Pownceby, M I, Ware, N and Pattel, R, 2017. Predicting iron ore sinter strength through X-ray diffraction analysis, in Proceedings Iron Ore 2017, pp 331–334 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

A technical exhibition was held in conjunction with the 4th DFI International Conference on Piling and Deep Foundations, Stresa. The exhibition was located in the ground floor of the Conference Hall. It was open from 15.30 on Monday April 8 till 16.30 Thursday April 11, 1991. The following is an alphabetical list of firms who took part. 1) A.P. VAN DEN BERG MACHINENFABRIEK B.V. P.O. BOX 68 8440 AB HEERENVEEN The Netherlands Tel: +31 5130 31355 Fax: +31 5130 31212 Stand Executive: A. Duyfjies

Jan 1, 1994

By J. L. Gillson

IN a brief summary of the many occurrences of fluorspar in our western states, it is not possible to go into detail in regard to the geology, mining and milling methods, and reserves about individual deposits. Rather a broad review is made of the occurrences and an analysis of how the western deposits may fit into our future domestic economy is presented. GENERAL STATEMENT ON FLUORSPAR SITUATION Fluorspar has been used for years as a flux in the manufacture of basic open-hearth steel, in foundry cupolas for melting pig iron, in the manufacture of opalescent glass and in the preparation of hydrofluoric acid. In 1880 the annual production of fluorspar in the United States was around 4000 tons per year. By 1900 it was up to 21,656 tons and between 1902 and 1908 it averaged about 40,000 tons annually. Prices were then so low, by present standards, that it seems impossible to believe now that mining could have been performed profitably at the price levels then prevailing. In 1890 fluorspar sold at the mines for $6.70 per ton, in I901 for $5.81, in 1916 for $5.92. When the United States entered World War I, fluorspar production and price skyrocketed; the production reached 263,817 tons in 1918, with prices above $20.00 per ton, and prices were even higher in 1919 and 1920. After 1920, the domestic production fell from the 1918 level to about 125,000 tons annually and the average price dropped back to about $I8.00 per ton. By 1935 the average price had fallen to $15.00, but in 194o with a rising demand the average price of all grades had gone back up to $20.31. Today it is 75 per cent higher than in 1940 and presumably the price of acid grade at least would be even higher if it were not for price ceilings. The first subsequent year that the domestic production exceeded that of 1918 was 1941, and the 1944 production is expected to exceed 400,000 tons, &apos;or over one and a half times that of 1918. In five-year periods, average production and imports were as are shown in Table I. [ ] Many people concerned with the consumption of fluorspar believe that the postwar period ahead will show a repetition of price trends of the last such period. They believe that imports will be- again an important factor in the available supply and the price will fall back gradually toward the prewar level. The following basic factors are pertinent in analyzing this conclusion:

Jan 1, 1945

By S. H. Brown

In our work as health physicists*, we do a lot of public speaking and interaction with the public on issues related to development of uranium mining and milling (?uranium recovery?) in the US. Understandingly, the public has important concerns about this. Accordingly, this paper is presented in a ?question and answer? format in which we have tried to capture what are some of the most common concerns we hear from citizens and address them. We have attempted to do so based on the best scientific information we have, representing information well documented in peer-reviewed scientific literature and consensus positions from both national and international scientific standard setting bodies and related committees. We have included some of the more important of these scientifically-based references to support the information provided. Practical space limitations prevent completeness in this regard in some cases. Visit the Health Physics Society?s web site or feel free to contact me directly for additional references, information or detail ? Steve Brown. The health physicist?s primary objective is to manage the beneficial uses of ionizing radiation while protecting workers and the public from potential hazards. For more information on what a health physicist is and on the Health Physics Society, visit the Society?s web site at www.hps.org.

Feb 23, 2014

By R. Bruce Ferguson

"IntroductionThe Beaverlodge Operation of Eldorado Nuclear Limited is a uranium property located near the north shore of Lake Athabasca about 7 miles from Uranium City, Saskatchewan.The mill is a 2000 tpd carbonate leach operation producing a high grade yellowcake concentrate.The Lamella Thickener was purchased to replace a 55 foot conventional unit which had deteriorated beyond repair. The cost of the unit was considerably lower than for a conventional unit, installation was much simpler and the unit is much more compact allowing it to be installed in the mill basement and be insulated completely.The unit was sized according to the results of tests performed both by the supplier and Beaverlodge engineering staff. The supplier guaranteed overflow clarities of less than 100 ppm suspended solids. The Lamella thickener was developed by A. Johnson Co. of Stockholm, Sweden, is manufactured under license by Parkson Corporation of Ft. Lauderdale, Florida and is distributed in Canada by A. Johnson Co. of Montreal."

Jan 1, 1975

By A. P. Cook

Gas samples were taken from a wide range of target areas on dumps arising from coal mining activities. Some of the dumps had largely burned out, some were still burning, some were in the process of rehabilitation, and on others rehabilitation was essentially complete. It was found that rehabilitation was very effective in reducing emissions to tolerable levels. Even incomplete rehabilitation reduced the CO2 emissions to less than about 1 kg/m2/a, whereas some unrehabilitated areas showed emissions of over 100 kg/m2/a. Some areas where there was active combustion taking place were also sampled, and they showed as much as 7 000 kg/m2/a, but the areas concerned were very small and their total contribution accordingly low. Analyses were also made for SOx, NOx, NH3, and CH4, but these were generally (and unexpectedly) at very low levels. The mines sampled represented 53 per cent of all surface coal mining activity. Accordingly the estimated total emissions were scaled up, to arrive at estimates of 1950 000 ± 350 000 t/a C02, 2040 ± 580 t/a SOx, 306 ± 85t/a NOx, and 31 ± 9 t/a NH3 for all surface mines. Methane was detected only from burning coal, and due to the difficulty in sampling, no reliable estimate could be made of these methane emissions.

Jan 1, 2012

By H. S. Baloyi, J. J. Rust

Spiral concentrators are widely applied to beneficiate commodities such as Cr2O3, mineral sands, and ferrochrome. The application of spirals for heavy minerals has been limited to a feed top size of 1 mm. At particle sizes larger than this, friction retards heavy particles and the particles' primary velocity approaches zero, resulting in a solids build-up, therefore inhibiting further separation. Recently, a new Multotec SC25 spiral model was introduced to the industry, which aids in beneficiating particles of up to 3 mm, with successes having been demonstrated in ferrochrome slag and titanium-bearing minerals. This spiral also has potential in electronic waste applications. This paper examines the applicability of the SC25 spiral in coarse Cr2O3 recovery. This stems from the fact that junior chrome miners tend to discard particles larger than 1 mm as they neither have milling nor dense media circuits. Also, alluvial chrome miners discard +1 mm even though this size fraction contains recoverable and liberated Cr2O3. The SC25 spiral has shown better Cr2O3 separation efficiencies than the SC21 model and with higher SiO2 rejection at saleable grades, thus providing an additional revenue stream specifically for the coarser (+820 μm) size fractions. Keywords: Spiral concentrators, chromite recovery, specific gravity, SC25 spiral, coarse spiral

Jan 1, 2020

Principal component analysis of the variation of Cu, Ni, Zn, Pb, Mn, and Cr in a control group of 96 samples of surface ironstone from the Yilgarn Block, Western Australia, was used to derive a simple graphical method, based on only Cu, Ni, and Cr, for discriminating between massive nickel gossans and other ironstones.When the graph was tested by plotting 400 control samples, it failed to correctly classify only nine out of 176 gossans and 11 out of 224 other ironstones.

Jan 1, 1974

By CIM Mineral Resource, Mineral Reserve Committee

The CIM Estimation of Mineral Resources and Mineral Reserves Best Practice Guidelines (MRMR Best Practice Guidelines) were prepared by the Canadian Institute of Mining, Metallurgy and Petroleum's (CIM) Mineral Resources and Mineral Reserves Committee (CIM MRMR Committee) to update an earlier version that was accepted by CIM Council on November 23, 2003 (CIM, 2003). These 2019 MRMR Best Practice Guidelines supersede and replace the November 23, 2003 version of the MRMR Guidelines. These 2019 MRMR Guidelines are not intended to be prescriptive and are not intended to provide detailed and exhaustive instructions for preparation of Mineral Resource and/or Mineral Reserve (MRMR) estimates. Rather, they are intended as general guidance to assist professional geoscientists (or equivalent) and engineers (or equivalent) in preparing high quality estimates of MRMR that incorporate sound geoscientific, engineering, evaluation and design practices. They are based on well-established estimation and mine planning principles and are designed to provide general guidelines of best professional practices employed in the preparation of MRMR estimates. Although the 2019 MRMR Best Practice Guidelines are intended for use by Canadian-based mining/exploration practitioners, many of the concepts and practices presented herein are in general agreement with current industry practices in jurisdictions with membership in the Committee for Mineral Reserves International Reporting Standards (CRIRSCO). For this document, persons preparing MRMR estimates are called Practitioners. Preparation of MRMR estimates should be carried out by Practitioners who either hold the status of Professional Geoscientist (or equivalent) or Professional Engineer (or equivalent), or who prepare the estimates under the supervision of a Professional Geoscientist (or equivalent) or Professional Engineer (or equivalent). For the purposes of this document, all references to reporting describe such necessary reports and related documentation that are created as part of the normal-course work flow of preparing MRMR estimates for internal purposes. For clarity, all public disclosure of MRMR estimates made by, or on behalf of, an issuer and intended to be, or reasonably likely to be, made available to the public in a jurisdiction of Canada must comply with the requirements of National Instrument 43-101 Standards of Disclosure for Mineral Projects (NI 43-101), as amended from time to time. At least one Qualified Person (QP) must take responsibility for each part of the estimation process when publicly disclosing the results of MRMR estimates. The intended audience for these 2019 MRMR Best Practice Guidelines includes Practitioners at all levels of skill and experience, government agencies, academic institutions, and the public.

Nov 29, 2019

By B. K. Loveday, N. V. Ramlall

A study was carried out to evaluate various batch flotation models for the recovery of minerals in a UG2 platinum ore. The major minerals in a UG2ore can be grouped as platinum group minerals, chromite, and siliceous gangue. This study also examined the entrainment of minerals during flotation. The models were ranked using statistical methods and an analysis of model-fit residuals. Entrainment parameters obtained from model fitting were evaluated for logic using a simple mineral-to-water ratio versus time plot. The foremost conclusion from the study was the importance of entrainment modelling. The measurement of water recovery increased the size of the data-set, and the inclusion of a simple entrainment model was statistically significant. The overall fit to the data was improved, and the entrainment model provided logical information on the recovery of gangue minerals that were not considered to be floatable.

Jan 1, 2015

By Paul Gilmour

"The principal role of the geologist is to recognize the existence of phenomena before trying to explain them" - B.M. Keilau, 1825; A. Holmes, 1965 Some important groups of mineral deposits in the layered rocks of orogenic belts or greenstone belts occur in horizons characterized by the presence of exceptional amounts of silica, iron and carbon, with more or less significant amounts of manganese. Generally, the rocks involved are well banded. In practice, these five physical features - four compositional and one geometric - are found with many lithological guises. Iron formation, in the full, modern sense of the term (James, 1954), quartzite, ferruginous quartzite, chert, jasper, "tetsusekiei" (Horikoshi, 1969), tuffaceous jasper ("purple porphyry" - Anderson and Creasey, 1958, p. 36), ferruginous or graphitic shale, argillite, slate or schist, and hematitic tuff are but a few of the more familiar of the names that have been assigned to these rocks. Widely acknowledged and well-documented examples of metallic deposits found in such sediments include concentrations of iron and manganese and stratabound, polymetallic, massive pyritic sulfides. Less familiar examples include occurrences of asbestos (Miles, 1953; and Coetzee, et al., 1976), antimony (Coetzee, 1976), and perhaps stratabound deposits of Au-Cu-U-W-etc., such as Aitik in Sweden (Mining Magazine, 1975; and Nilsson, 1979) and Olympic Dam in South Australia (Roberts and Hudson, 1983). The case of gold is intriguing. An association between gold and iron formation has been identified at several famous deposits and districts, such as Yellowknife, N.W.T. (Morton, 1979), Homestake, S. Dak. (Sawkins and Rye, 1974), Vubachikwe, Zimbabwe (Fripp, 1976) and the Barberton district, R.S.A. (Hammerbeck, 1976). Yet a critical reading reveals the existence of many other hitherto unsuspected examples. The purpose of this note is to draw attention to that omission and the apparent explanation for it. It is not hard to detect the two most probable reasons for the discrepancy between reality and the record.Most occurrences of gold are associated, not with the familiar banded iron formation or interbedded magnetite and chert (technically, the magnetite-banded variety of the oxide facies), but with the enigmatic carbonate, sulfide and silicate facies of iron formation and/or with rocks evidently related to iron formation. All too commonly, the unfamiliar facies of iron formation have been identified by field and mine geologists and not a few researchers as products of regional metamorphism and hydrothermal alteration, as mafic igneous rocks, or as conventional sediments, ie., without regard to their intrinsically ferruginous nature. The justification for these two complementary assertions is largely to be found in the recognition of a characteristic suite of metals and minerals in gold deposits known to be associated with iron formations. Although, from a geological standpoint, a lithological association is more important than a mineralogical assemblage, the latter is the more likely of the two to be diagnostic. This arises from the different natures of mineral and rock classifications, The identification of a mineral or an element is a matter of fact. Owing to the genetic component inseparable from petrographic nomenclature, viz., "igneous": a rock (believed to have been) derived from a melt, the identification of rocks depends on inferences or conclusions about their mode of formation - conclusions that are commonly debatable and, all too often, involve subjective judgements. This is especially prone to be true, if - as at many of the gold occurrences in question - the host rocks have been metamorphosed and/or "altered". In the notes that follow greater weight has accordingly been assigned to elemental and mineralogical than to host rock composition. In other words, if, in a given gold occurrence, the suite of metals and minerals present conforms to the standards of the subject class, whereas the names assigned to host rocks do not, the latter will be viewed as suspect.

Jan 1, 1985

By W. L. Falke

The Bureau of Mines has developed a system that permits the "soft" soldering of aluminum and aluminum alloys with standard tin-lead solders. The method employs application of a thin nickel-copper-alloy coating to the substrate, which enables the tin-lead solders to wet readily and spread over the areas to be joined. With conventional technology, aluminum and aluminum alloys are extremely difficult to solder because tenacious surface oxide films prevent wetting. With the Bureau-developed method, the aluminum substrate is mechanically or chemically cleaned to facilitate bonding to a minute layer of zinc that is subsequently applied with an electroless zincate solution. The nickel-copper-alloy (30 to 70 pct Ni) coating is then applied electrolytically over the zinc, using immersion cell or brush-coating techniques. Development of acetate electrolytes has permitted deposition of the proper alloy coatings. The coated areas can then be readily joined with conventional tin-lead solders and fluxes. The joints so formed are ductile, strong, and relatively corrosion resistant, and exhibit strengths equivalent to those formed on copper and brass when the same solders and fluxes are used. The method has also been employed to soft-solder magnesium alloys.

Jan 1, 1983