Search Documents

By A. U. Seybolt

RECENTLY, cases of coexisting ordered and disordered phase equilibria have been reported among face-centered cubic metals,1"3 but not on body-centered cubic systems.4 McQueen and Kuczynski5 showed a single line as the boundary between ordered solid solution of Fe3Al type and corresponding disordered solution in the Fe-A1 phase diagram based mainly on dilatometric and magnetic measurements. Such a single line would indicate a second or higher order transition. or an absence of coexisting order and disorder. The writer found previously a two-phase equilibrium region at 800°C consisting of ordered and disordered solid solutions of Fe3Si in a matrix of approximately 1-6 wt pct Si (Fe3Si is of 14.3 wt pct Si). A similar two-phase region of ordered and disordered Fe3Al solid solutions might be expected if the similarity between Fe3Si and Fe3Si structures hold true. In the present investigation, a wire of 22 at. pct Al, balance Fe and 0.0513 cm in diameter was subjected to electrical resistivity measurement in vacuum as a function of temperature between 300 and 800°C, see Fig. 1. There was excellent agreement between data taken on heating and on cooling: no hysteresis was observed. The Curie temperature was determined to be 640 °C which agrees with the finding by McQueen and Kuczynski.5 But in addition, there were two transitional points in the resistance-temperature plot at 510oC and 400 "C. The former is thought to be a connection with the transition from disordered state to a coexisting order and disordered equilibrium state; while the latter, from such coexisting state to ordered state. Fig. 2 shows a phase diagram where the suggested two-phase region lies between dotted lines. The solid lines are those of McQueen and Kuczynski.5 Since these authors found only a single-phase boundary between ordered and disordered Fe3 Al, it would seem likely that the dilatometric method used by these authors was not sufficiently sensitive to resolve the ordering reaction into the two-phase boundaries. In addition, their phase diagram conflicts with the statement they make on P. 1 of their paper: "The sharpness of the peaks indicates that ordering to Fe3A1 is a first order reaction." The suggestion of coexisting order plus disorder in Fe3A1 must be considered tentative until confirmed by high-temperature X-ray examination. If

Jan 1, 1961

By Shosei Serata

The Stress Control Method improves productivity and safety in underground coal mining. The method stabilizes the roofs and floors of mine openings in both shallow and deep coal beds, regardless of whether or not there are ground stability problems. This paper describes the means by which a tapered pillar experiment is used to collect in situ data, which is then used as input for a computer model. The resulting computer model is then used to optimize Stress Control design for the mine under study. The behavior of any underground coal mine is not elastic, as is generally conceived in the conventional view of rock mechanics, but rather is highly time-dependent and site-specific. Unfortunately, conventional rock mechanics methods based on the elastic principle are not able to capture the highly non-elastic nature of ground behavior which actually occurs. To capture actual behavior, a new method of study is required. In this regard, geomechanical study of an underground coal mine may be compared to studying the behavior of a living fish. Its true behavior zannot be understood by examining it "dead in the laboratory. It Is the "live" nature of the coal mine that is required for design optimization of the Stress Control Method in the given mine. The Stress Control Method is based on a time-dependent theory of the global behavior of the mine ground, which generally contradicts the conventional elastic theory of ground behavior. Therefore, site-specific adaptation of the Stress Control Method required a comprehensive understanding of the global behavior of the mine as a function of time and site-specific ground conditions.

Jan 1, 1986

By Tim Peterson

Factors Controlling Stability Stability of slopes in soft rock, waste dumps or soils is governed by three factors: ?Slope configuration ?Groundwater ?Shear strength

Jan 1, 2004

Precast prestressed concrete piles designed to be end-bearing in a sand stratum at Drax Power Station met with extremely variable resistance during driving. Some piles came to virtual refusal almost immediately on entering the sand whereas others were driven to considerable penetration with very low resistance. Redriving and load tests on piles experiencing low resistance on initial drive showed that take up in strength occurred over a relatively short period of time. Investigations involving the use of pneumatic piezometers revealed the development of significant excess pore pressures during driving. Samples from boreholes showed that piles met the least resistance when the sand had a high silt content. Comparison with the original site investigation data demonstrated the difficulties in predicting detailed pile behaviour. The varied behaviour could not be related to the original borehole logs or to SPT or static cone penetrometer results. The factors controlling pile driving behaviour were essentially geological and could only be explained with reference to local soil grading.

Jan 1, 1989

In an earlier paper (Stanton, 1953) a brief account was given of the geological environment and structure of the Lloyd Copper Mine orebody, Burraga, N.S.W. The present paper is concerned with the chemical and mineralogical features of the ore from this mine.Investigation has been made difficult because of inaccessibility of the workings, which have been fallen in for many years. The exact positions within the orebody of the specimens described in this paper are known in only a few cases. The specimens examined are from the collections of the Mining and Australian Museums, Sydney, and from material collected by the writer from the upper parts of the mine and from various dumps about the old workings.However, no significant variations in the nature (as distinct from grade) of the ore have been mentioned in the old reports, or by Carne (1908) or Kenny (1928), so it is likely that the specimens examined are reasonably representative of the orebody as a whole.CHEMICAL CONSTITUTIONThe ore is of simple and apparently very uniform composition.It is essentially a copper ore, with minor amounts of zinc and very minor amounts of lead. Plotting of copper against zinc shows a more or less sympathetic relationship between these at least as far as 20 per cent. copper - the highest grade assayed during the present investigation. The trend of the plots indicates a Cu/Zn ratio of about 15/1 to this point. Lead is very low and extremely sporadic, showing no clear relationships with the other metals.MINERAL COMPOSITIONThe principal non-opaque minerals are quartz and sericite, and these are accompanied by smaller quantities of muscovite, calcite and biotite. Quartz is the most abundant mineral, occurring both as a C'onstituent of the country rock a quartz-sericite schist-and as veins. All quartz aggre...

Jan 1, 1955

Your thoughts on the current status of the global minerals industries? The global economic, technological, social and political changes of the last two decades of the 20th century resulted in the emergence of a restructured minerals industry. This industry is now based on a new cost-cutting philosophy; utilization of modern technology; productivity gains rather than production tonnages; diversification of mineral markets; and globalization of exploration, mining and processing. Quantity and tons used to be the focus. The emphasis today is on remaining competitive in the marketplace by lowering per-unit production costs as much as possible. What factors and trends will impact the minerals industries in this, the 21st century? A number of parameters will impact minerals operations and shape the future sustainability and growth of the minerals industries. Increased demand for minerals will be accompanied by the demand for technical advancements. We will also see a continued emphasis on health and safety, environmental stewardship, and education and training. Let me elaborate.

Jan 1, 2002

By J. C. Taylor

The Rhodax inertial cone grinder, designed by France?s FCB Group Fives, is the result of three years, theoretical and mechanical research in the field of compression grinding by the research staff of FCB?s CRM minerals research centre. A number of potential uses have been assessed and will be discussed in the paper. The crusher is an inertial grinder that works on the pressurized bed fragmentation principle. The fragmentation force is caused by the rotation of unbalanced masses rather than by an eccentric mass, as is the case in a conventional crusher. This makes it possible to achieve very high reduction ratios. By controlling the speed of rotation of the unbalanced masses, the grinding force can be modified, thus changing the product size distribution. The paper describes the machine layout, operating principles, control parameters and will briefly describe the results obtained on reef, waste and ROM reject pebbles. Some comparisons are made with conventional crushing.

Jan 1, 1998

By Rodney P. Smith

The diffusivity of carbon (0.1 wt pct C) in Fe-Nz alloys (0 to 100 pct Ni) has been determined for the temperature range 860° to 1100°C. As a function of nickel content, the diffusivity has a maximum near 60 pct Ni (the maximum diffusivity being about 1.3 times that in the absence of nickel); the activation energy has a maximum between 40 and 50 pct Ni and a maximum between 80 and 90 pct Ni. The difference between the minimum activation energy and that in iron is about 3000 cal pev g-atom; Do has a minimum between 40 and 50 pct Ni and a maximum between 80 and 90 pct Ni. The results cannot be rationalized by an approximate thermodynamic treatment. THE diffusivity of carbon has been determined in a number of iron alloys over a limited concentration range. It seemed desirable to investigate a system which allows an extended range of alloy composition within a single-phase region. The Fe-Ni system is ideal in this respect, in that all alloys from 100 pct Fe to 100 pct Ni are fee in a convenient temperature range.&apos; The carbon diffusivity was determined by a decar-burization method. The experimental procedure was identical with that used to determine the diffusivity of carbon in y Fe-Co alloys.2 The experimental data are given in Table I. A small correction (order of a few percent) has been made to the measured carbon loss to correct for the carbon lost from the ends of the cylinders.&apos; Since the diffusivity of carbon varies with carbon content the measured diffusivity is an average value for a carbon content between zero (surface) and that at the center of the sample at the end of the decarburization periods. In making the correction in D to 0.1 wt pct C it is assumed that the measured D corresponds to the arithmetical mean of the carbon content at the surface and at the center of the sample at the end of the decarburization period.3 Since this correction is small (<4 pct in D) and since for our decarburization times the changes in carbon content at the center of the sample was small the mean carbon content could have been taken as half the initial value. It is further assumed that the change in D with carbon content for the alloys is the same as that for the diffusion of carbon in iron. From the data of Wells, Batz, and Mehl4 and of smith5 the correction of D from the mean carbon content to 0.1 wt pct C is 0.3 (0.1 - mean wt pct C). The results for iron are given in Ref. 2. Within the experimental error log Do.l%C for each alloy is a linear function of 1/T; the constants for the equation determined by the method of least squares are given in Table I. The deviations of the experimental points from the least-squares line are of the order of 2 pct in D. A comparison of our results for the diffusivity of carbon in nickel with those of other investigations is shown in Fig. 1. The lower curve in Fig. 1 is a linear extrapolation of values calculated* from the equation of Diamond6 for the relaxation time (temperature range 100° to 500°C). The results indicate a small increase in the activation energy over the temperature range 100° to 1400°C; however, it is difficult to say whether the change in Q is real or experimental error. Certainly the change in Q is less than the variation of 5 kcal per g-atom in the diffusivity of carbon in a iron.6 The experimental data for all the alloys are plotted in Fig. 2. As a function of nickel content the diffusivity has a maximum near 60 wt pct Ni at all temperatures investigated and possibly a minimum between 80 and 90 wt pct Ni for temperatures below 1000°C. The activation energy, Q, and log Do are plotted as a function of the nickel content in Fig. 3. Due to the limited temperature range of our experiments neither Q nor Do can be determined precisely; the activation energies appear to be consistent to ±0.3 kcal per g-atom; however the deviation from the absolute values may be considerably larger, see Table II. The Do values probably have little significance. The solid line for Do in Fig. 3 represents the values required to reproduce the experimental values for D when Q has values represented by the upper solid line The diffusivity of carbon may be expressed in terms of the mobility B22, the activity coefficient r2,

Jan 1, 1967

By T. T. Chen, J. E. Dutrizac, G. Poirier

In the Waelz kiln process, EAF dust is converted to an Fe-rich slag, a (Zn, Fe)-rich dust that is recycled to the kiln and the Zn-rich Waelz oxide which is subsequently up-graded for the recovery of zinc. To clarify the reactions occurring, the Waelz kiln products from a European Waelz plant were characterized mineralogically to determine the mineral species present, their micro-textures and the metal carriers. The EAF dust contains 27 % Zn, and consists mainly of ZnFe2O4 and ZnO, together with minor to trace amounts of NaCl, PbCl2, KCl, CaO, Ca2Fe2O5, Fe203, FRO, Pb oxide and various Ca-Fe-Al-Mn silicates. The KCI and NaCI sometimes agglomerate the other particles. The slag consists of nodules which often exhibit colloform structures. The slag contains of variable amounts of Fe, FeO(OH), FeO, gypsum, Ca(OH)2, Ca2SiO4 and various Ca-Fe¬Al-Mg-Mn silicates as well as minor to trace amounts of ZnFe2O4, Cr-Fe oxide, Mn-Fe oxide and other species. The Waelz oxide contains 57-61 % Zn, and consists predominantly of ZnO, with minor to trace amounts of KCI NaCl, Pb(OH)Cl, Pb20(SO4), Pb chloride, ZnSO4, ZnFe2O4, Ca2SiO4, Ca2Fe2O5, Ca-Fe silicate and NaZn4(SO4)(OH)6Cl.6H2O. The KCI agglomerates the other particles in the Waelz oxide. The recycled dust appears to be a mixture of EAF dust and Waelz oxide, but it contains relatively more coarser-grained metallic Pb and Pb oxide particles.

Jan 1, 2004

By Sahoo K. C

Traditionally, the blast furnace (BF) has maintained a dominant position as the primary source of iron units. Notwithstanding the efficient nature of the process in respect of its material and energy consumption, the conventional blast furnace route is faced with limitations such as stringent quality metallurgical coke, high capital investment, etc. While BF will continue to retain its predominant position as the foremost ironmaking technology, the alternate processes may also have a role to play. Direct Reduced Iron (DRI) or sponge iron industry is all set to take a firm root in India as one important solution to the problems of shortage of metallurgical coal and ferrous scrap and high investment costs faced by the country&apos;s steel industry. The commercial proven DR processes coupled with electric arc furnace (EAF) steelmaking have also offered a viable alternative to the blast furnace - basic oxygen furnace (BF - BOF) route for the installation of integrated plants under specific local conditions. The performance and efficiency of DRI processes mainly depend upon the chemical and physical behaviour of the raw materials especially the iron bearing materials. Iron oxide pellet and sized lump ore constitute the oxide feed stock, while pellets form an ideal feed stock for direct reduction, use of lump ore is economically advantageous because of its lower price. National Mineral Development Corporation Limited (NMDC), being one of the major producer of iron ore in the country since last four decades, has established technology and developed process flowsheets for production of suitable calibrated lump ore for DRI production, besides supplying the natural lump ore for conventional blast furnace requirements. In addition to the above, extensive pilot plant tests have been carried out at the R&D Centre of NMDC for preparation of iron ore concentrates suitable both for direct reduction and blast furnace grade pellet feed using the iron ore fines from its own mines and as well as from the other iron ore mines in the country. For utilisation of the huge quantity of slimes generated in its ore processing plants, NMDC has planned to set up the first commercial plant adopting the smelt reduction process (ROMELT Process) for production of pig iron from Bailadila slimes. The paper mainly deals with various beneficiation techniques adopted for production of DRBF grade pellet feed from iron ore fines. Also presented in the paper, the extensive work carried out at R&D Centre on preparation and evaluation of calibrated lump ore (Natural Pellets), based on which, suitable modifications are incorporated in the ore processing plants of NMDC for production and supply of the same to sponge iron industries.

Jan 1, 1999

By W. Mueller, M. Rocheleau, E. Dimroth

The paleogeographic evolution of the Abitibi Belt is subdivided into three phases, namely: 1) a phase of the growth of a submarine volcanic chain, 2) a phase of the emergence and growth of volcanic islands and 3) a phase of uplif t and erosion of volcanic islands. Isostatic calculations suggest that the volcanic sequence in the south of the Abitibi Belt rests on oceanic basement or on the mantle; the volcanic sequence in the north of the belt rests on about 13-14 km of tonalitic basement. 10-15 km of plutonic material accreted to the volcanic islands during paleogeographic phases 1 and 2, and caused the uplif t during paleogeographic phase 3.

Jan 1, 1984

By Warren L. J

The effectiveness of shear-flocculation as a method for upgrading simple mixtures of ultrafine (1-11 \lm) scheelite and garnet was evaluated. Statistical methods were used in the design and analysis of the main test program.The stirrer speed, stirring time, and initial weight ratio were all found to have significant effects on both the recovery and grade of the floes produced. The particle sizes also had an effect on the final grade. There were several important interactions between factors which also affected the results. Optimum conditions for shear-flocculation were established, and under these conditions about 80 per cent of the scheelite could be recovered at a grade which depended on the composition of the starting mixture. Starting with mixtures containing 10 and 50 per cent scheelite, the best final grades were between 20 and 50 per cent and between 70 and 90 per cent respectively, the actual value depending on the particular combination of particle sizes.

Jan 1, 1977

An account is given of experimental apparatus for generating a short duration high velocity water jet and the effect of its impingement on various rock samples under air or water cover. The penetration was found to be highly dependent upon the rock structure; in general material with closely interlocking grains was resistant.The damage sustained by a stationary sample held close to the jet did not vary greatly whether the sample was in air or confined under a water layer; but when the sample was translated under the jet there was a marked increase in the damage sustained.Some consideration was given to the possible practical application of a water jet for deep hole drilling and an estimate made of the power requirements and transmission losses for such a system.

Jan 1, 1969

By Jim Baumann

Deposited millions of years ago in irregular paleokarstic channels, Jamaica’s extensive bauxite deposits provide good quality ore for alumina production and subsequent aluminum smelting. Bauxite mining operations are critical to the Jamaican economy. It accounts for a large percentage of Jamaica’s export earnings. Bauxite production in Jamaica accounts for about 10% of the world’s output each year. Bauxite deposits in Jamaica lie close to the surface. They can be extracted using standard surface mining techniques. The deposits occur in scattered pockets across the country’s rugged landscape. So it was necessary for two of the country’s major mining and refining operations to implement cost effective methods for the acquisition and management of bauxite reserves and surface ownership distribution rights.

Jan 1, 2002

By Jeong-Soo Sohn

Physical treatment and chemical treatment of spent lithium-ion battery were studied in our research team. Especially we developed two types of acidic leaching for crushed powders containing LiCoO2 of spent lithium ion battery. One of them is sulfuric acid leaching with H2O2 as a reducing agent. The leaching rates of cobalt, lithium and the other metals were above 99 % at the condition of 2 M H2SO4, 10 vol. % H2O2, 75 °C, 300 rpm agitation speed, 250 g/5L solid liquid ratio and 75 minutes reaction time. And the other leaching process is the oxalic acid leaching. In this process more than 99% of Li and less than 1% of Co were dissolved at the condition of 3M oxalic acid, 80°C reaction temperature, 300rpm agitation speed, 50g/L initial solid/liquid ratio and 90min extraction time. Each process has its advantage and disadvantage. In sulfuric acid leaching, leaching reagent is very cheap and cobalt could be recovered into cobalt hydroxide. On the other hand, oxalic acid is more expensive than sulfuric acid but lithium could be dissolved selectively. Also cobalt could be recovered into cobalt oxalate and it could be changed into cobalt oxide after heat treatment. In order to select the effective recycling process, recovery rate and purity of cobalt hydroxide and cobalt oxalate were compared and it was investigated which process was more environment-friendly and economical.

Jan 1, 2006

By R. E. Hudrlik, G. W. Preckshot

The diffusion coefficients of silver from solid silver in molten lead were measured to within ± 0.8 pet in a columnar type diffusion cell ower, the temperature range of 326° to 530°C. Fick&apos;s law describes the process up to 530°C where the laminar mechanism appareltly breaks down. These is negligible resistance at the interface as shown by mathematical analyses. The diffusion coefficients are found concentration independent. IT would seem that diffusion in liquid metals would be free of such effects as molecular structure, dissociation. polarization. and compound formation. This view was taken by Gorman and preckshot in their study of diffusion of copper from solid copper into molten lead. They reported diffusion coefficients which were independent of the concentration over the range of 478° to 750°C. They found that the Stokes-Einstein equation with constant radius of the diffusing specie represented the diffusion data better than Eyring&apos;s rate theory equation and Sheibel&apos;s correlation. The radius of diffusion was found to be that of the doubly charged copper. There appeared to be no resistance across the solid-liquid boundary. In the present work the diffusion coefficients for silver in liquid lead were measured over a range of temperatures of 350° to 505°C. The solubility of silver in lead over the range of 303° to 630°C was also obtained. These results are compared with calculated or correlated values or with data in the literature. EXPERIMENTAL Procedure—The experimental equipment techniques and procedures were those reported in detail by Gorman and preckshot9 and will not be repeated here. Measured values of WT, Co, A. L were obtained for various diffusion times and the diffusion coefficient was computed for the case of no resistance at the interface9, 11 by: WT/CoAL = 1- 8/p2 n=1 1/(2n - 1)2 exp[-(2n - 1)2p2 Dt/4L2] [1] or where there was resistance at the interface by: WT = 1- ?n=1 2h2/ap2L [sxp [-Dan2t]/[(h2 + an2) L + h] The roots an are those of the transcendental equation3 tan (an L) = Iz/cun. The diffusion coefficient is that defined by Hartley and Crank.7 The total silver in the lead cylinder and equilibrium slug was determined by a cupellation technique&apos; with proper correction for losses. Analysis of known samples showed that this method is surprisingly accurate. The amount of silver in the lead adhering to the silver cylinder was obtained in the same fashion as shown by Gorman and preckshot.9 The small errors involved in this determination are not critical since the silver in this adhering lead layer is only 3 to 15 pet of the total diffused. Materials—Electrolytic silver containing 99.9+ pet Ag obtained from General Refineries of Minneapolis, Minn. was used for all but runs 7 and 8. For the balance of the runs this silver was reduced with hydrogen at 1100°C and its oxygen content was found to be about 0.017 pet. For the runs. 7 and 8, phosphorous-reduced silver of the same purity was obtained from Handy and Harman Co. of Chicago, Ill. The densities of the phosphorus-reduced silver and the hydrogen-reduced electrolytic silver were 10.484 and 10.487 g per cm3, respectively. These values agree with those reported for pure silver. Silver which was reduced at 900 C had an average density of 9.998 g per cm3, indicating porosity. This silver was used for a number of runs which were not tabulated in Table I. These are indicated by crosses on Fig. 2. The 99.999 pet Pb was obtained from the National Lead Co. Research Laboratory of Brooklyn, New York. DISCUSSION OF RESULTS The diffusion and solubility results are reported in Table I for eleven runs using either phosphorus-reduced electrolytic silver or hydrogen-reduced silver at 1100° C. The solubility data shown in Fig. 1 show the excellent agreement with that reported by Heycock and Neville.8 The data of Friedrichs5 apparently are in error. The experimental solubility data of this work are reported to 0.3 pet. The experimental diffusion coefficients computed from Eq. [1] are reported within 1.2 pet of the mean and are plotted in Fig. 2. These are expressed within +0.8 pet of the experimental values over the entire temperature range by: D= 8.26 x 10 -5 e-1925/RT . [3] There appears to be little difference due to the

Jan 1, 1961

By French D

In presenting this paper may I preface my remarks by recognizing the presence here to-day of the many delegates from the overseas mining communities throughout the world. That is to say - those delegates not representative of Companies resident in Australia. This does not mean that my comments following are directed solely to the Australian exporter - far from it. The Company which I represent is internationally based. The experiences we have had in dealing and negotiating with our good friends the mineral cargo shippers vary very little in any operational area. However for the purposes of this exercise this address is based on some of our experiences within the Australian trade scene with the emphasis on the fact that we believe it has application to all trading areas.

Jan 1, 1989

Ilmenite production in Western Australia commenced in 1956. There are now five producers, all in the Bunbury-Capel district, and current total production capacity is about 450,000 t.p.a.The deposits occur near the surface and average between 10 and 50 per cent heavy mineral. About 70-85 per cent of the heavy mineral is ilmenite. Other heavy minerals present include leucoxene, zircon, rutile, monazite, and garnet. The ilmenite contains 52-60 per cent Ti02. and is very low in chromium (0&#183;03-0&#183;04 per cent CrS03)Mining is done by sluicing, drag line excavation, or dredging. Primary concentration of the heavy minerals is achieved by spirals, revolving cones, or Reichert cones. After drying and screening, ilmenite is separated from the heavy mineral concentrate by various types of magnetic separator.Separate leucoxene, zircon, rutile, and monazite concentrates are also produced. Each plant uses a different technique and the processes used include chemical attritioning, screen plate electrostatic separation, high tension rolls, air tables, and dry launders.INTRODUCTIONThe treatment of beach sands in the Bunbury/Capel area for the extraction of ilmenite is a very recent development in the mining industry in Western Australia. Nevertheless, since the commencement of production in 1956, ilmenite has become the sixth most important mineral produced (Table 1).The increasing world recognition of Western Australia as a major producer of ilmenite (Table 2) is due primarily to the low chromic bxide content of the mineral (0&apos; 03-0&apos; 04 per cent Cr203), combined with a medium to high titanium dioxide content (54-60 per cent Ti02), supported by large reserves, a stable government, and close access to good shipping facilities. Ilmenite is. produced from these deposits at low cost which enables the industry to compete on world markets despite high rates for sea freights because of the distance from major markets.

Jan 1, 1965

By K. Mallikarjuna Rao

There are several methods available to estimate deflection and ultimate Capacity of laterally loaded piles. In this investigation an attempt has been made to verify the existing methods for prediction of ultimate lateral resistance and deflection with the laboratory and field test results reported in the literature. A 75 pile loading test data obtained from the literature was used to evaluate two methods designed to predict the ultimate lateral resistance of rigid piles and three methods designed to predict the lateral deflections of rigid piles and four methods designed to predict the lateral deflection of flexible piles subjected to lateral loads. The accuracy and precision of each method is quantified statistically. The statistical results of the overall analysis indicate that the mean values of the ratios of predicted to measured lateral capacities vary from 0.62 to 1.14 with an average of 0.88. However, the settlement predictions were much more widely scattered than the ultimate load predictions and in general all the methods have a tendency to under predict the deflections. A new method is proposed by modifying the Broms&apos;s method to estimate the lateral deflections of free headed rigid and flexible piles separately. The proposed modified methods were found to be reasonably good in comparison to existing methods and to overestimate deflections.

Jan 1, 1996

By Robert N. Morris

Ladies and Gentlemen: It is a distinct pleasure and honor to appear before you representing the railway industry as I do, but there is a much closer personal relationship. I am a graduate Mining Engineer and worked in the coal industry for 15 years prior to becoming a railroader only 4 ½ years ago. I have been a member of AIME most of my adult working life and am currently active in the Washington, D. C. Section. While having been in the railway industry only a short time, I have become involved during the recent period of innovation and development of the new railroad technique known as unit train service. I have had the privilege of helping to work out a number of unit train movements to both electric utility companies and to a major steel concern, handling coal from mines on the Southern Railway to the consuming plants. On Southern, our unit trains are all of what I shall describe as shuttle train operations whereas within the railroad industry today several types of service are characterized as unit train service and many don&apos;t offer comparable efficiencies.

Jan 1, 1968