Search Documents

By Wallace W. Roepke

The Bureau of Mines tested new designs of drag bit cutters with sintered diamond inserts instead of standard tungsten carbide tips. The bits were tested for orthogonal cutting forces, primary dust generation, and incendivity, with a standard plumb-bob type conical cutter (600 included tip angle) as the reference. Preliminary wear and impact-failure testing were also done. The results were mixed. Two new designs had forces similar to those of the reference bit, but one new design had about twice the normal force. This same design had almost twice the specific energy during shallow cutting but generated an equal or slightly lower amount of primary dust than did the reference bit. Incendivity was eliminated for two radial designs. One conical design had ignition only after more than 15 impacts, but the other conical design was incendive. Impact failure occurred, but not so quickly as anticipated. Over 7,500 impacts on a sandstone face, with a total cutting distance of more than 1,981.2 m, only scuffed the leading edge of the sintered diamond cutting face but put hairline cracks in the substrate mounting pad. Additional design and testing are needed to develop an optimum cutter, but prospects look good for this material.

Jan 1, 1983

By W. R. Reed

The National Institute for Occupational Safety and Health (NIOSH) uses light-scattering dust monitors (nephelometers) in its research to develop dust controls to reduce respirable silica dust overexposures in miners. Recently, the model 1500-pDR, an active nephelometer, was introduced by Thermo Scientific. Testing was completed to ensure compatibility with the metal/nonmetal mine dust personal sampling unit (M/NMDPSU). Results of testing demonstrated that gravimetric concentrations measured from the 1500-pDR are comparable to the gravimetric concentrations measured using the M/NMDPSU, without need for correction, under commonly observed dust loading conditions.

Jan 1, 2012

By R. Karl Zipf

The sudden, violent collapse of large areas of room-and-pillar mines poses a special hazard to miners and mine operators. This type of failure, termed a "Cascading Pillar Failure" (CPF), occurs when one pillar in a mine layout fails transfering its load to neighboring pillars causing them to fail, and so forth. Recent examples of this kind of failure in coal, metal and nonmetal mines in the U.S. are documented. Mining engineers can limit the danger posed by these failures through improved mine design practices. Whether failure occurs in a slow, nonviolent manner or in a rapid, violent manner is governed by the local mine stiffness stability criterion. This stability criterion is used as the basis for three design approaches to control cascading pillar failure in room-and-pillar mines, namely, the containment approach, the prevention approach, and the full extraction mining approach. These design approaches are illustrated with practical examples for coal mining.

Jan 1, 1996

By K. Meyer

"The largest cost centres of the David Bell Mine concentrator are grinding, leaching and effluent treatment. Optimizing results during the 6th year of operation are listed below: o SAG mill slurry density control and operating strategies improved liner life and media consumption by 10 and 25%, respectively.o Poly-met liners clad the SAG mill except for the feed end. Lower noise levels and reduced mill downtime have resulted in an improved and more efficient workplace (time required for liner changes is 2 to 3%).o A comparative grinding media study using seven different marked media at the same time showed media wear rates range 120 to 198 mg/kWh and ball mill charge replacement frequencies of 8.3 to 13.1 per year, and that a meaningful wear test must include all media to be tested at the same time in the same mill. High quality carbon steel cylinders had the best economics.o Pre-aeration, using pure gaseous oxygen is accomplished in pipe reactors. Small bubble generators provide oxygen in the first three leach tanks. 1500 to 3000 kg of oxygen is consumed per day. Leach kinetics have improved and trends indicate increases in gold recovery of three to seven ounces per day at reduced costs. Effects of reduced cyanidation of accessory metals on the effluent treatment plant will be discussed in a separate paper."

Jan 1, 1991

By Bora Derin, Onuralp Yucel, M. Seref Sonmez, Murat Alkan

"Latest stage in the production of boron carbide by metallothermic methods using magnesium was the leaching process. Boron carbide particles obtained by self-propagating high temperature synthesis contained several impurities such as magnesium oxide and magnesium borates after the metallothermic reactions. Removal of such contaminates by hydrometallurgical methods required to produce high purity boron carbide. Leaching by concentrated hydrochloric acid solutions resulted in the production of pure boron carbide together with high magnesium and boron containing solutions. Removal of such ions from the spent liquor was the necessity to have dischargeable solution. In this study, precipitation of magnesium and boron compounds from relevant chloride containing spent liquors and the production of saleable products was aimed. The effects of chemical reagents, pH of the solution on the precipitation efficiency of magnesium and boron compounds were investigated in the study. Chemical analysis and the characterisationof solid phases by using x-ray diffraction analysis were the latest stage.Introduction A variety of advanced ceramics, inter-metallic, organic and inorganic compounds, oxygen free single crystals, and polymers can be synthesized by using different SHS techniques [1, 2, 3]. In the SHS process, after initiation, reaction becomes self-sustaining and propagates in the reactant mixture. A high amount of heat which is generated during the process accelerates the reaction rate and thus it makes the process highly productive and economically feasible for different production scales. After the SHS process obtained powder mixture needs to reacted with acidic solutions to purify the product. In this case B2O3 was reacted together with C and Mg to synthesis fine B4C powder resulted in the production of MgO as well according to the Eq. 1 and then MgO was removed from the mixture by leaching with the concentrated HCl solution as shown in Eq. 2, respectively [4, 5]."

Jan 1, 2008

By N Kado, T Iwama, R Inoue, S Ueda

Steelmaking slags are usually used as roadbed and civil engineering materials. However, the expansion phenomenon, which is caused by the volume expansion during hydration of free CaO and free MgO contained in steelmaking slag, is indispensable. Since the hydration of free MgO in steelmaking slag is much slower than that of free CaO, it is qualitatively considered that free MgO contributes to the hydration expansion of steelmaking slag over a long period of time. Similar to free CaO, free MgO consists of undissolved MgO and crystallised MgO in steelmaking slag. The latter precipitates during slag cooling. When divalent metal oxides (FeO, MnO, CaO) are dissolved in the crystallised MgO to form a MgO-based solid solution, it is expected to inhibit the hydration reaction similar to precipitated CaO. From the previous hydration test of Magnesioferrite, which was calcined after mixing MgO and Fe2O3 reagents, it was found that the higher the Fe2O3 concentration, the slower the hydration reaction progressed. In this study, by clarifying the influence of calcination conditions of MgO-FeO and MgO-FeO-MnO solid solutions, which were prepared by the calcination of mixture of MgO, FeO and MnO reagents, on their hydration reactivity, the effect of composition and thermal treatment on the formation of free MgO that is not hydrated (or easily hydrated) were discussed. To investigate the influence of MgO grain size, coarse MgO particles, which were obtained by crushing MgO crucible, were also used for heat treatment. With increasing the amount of FeO and MnO in the MgO-FeO-MnO solid solution, the hydration reaction became more suppressed. The expansion suppression effect was higher with solid-solved FeO than with solidsolved MnO. When the calcination temperature of the MgO-FeO solid solution was increased, the Fe3+/Fe2+ concentration ratio increased, resulting in a higher hydration rate.

Jun 19, 2024

By Paola Lazari de Aguiar

A indústria automobilística, principalmente, tem exigido o desenvolvimento de novos materiais que permitam a redução do peso dos veículos devido ao impacto do peso no consumo de combustíveis e emissão de poluentes. Assim, novos estudos têm sido realizados visando a redução da densidade dos aços através de adições consideráveis de alumínio. Neste contexto, este trabalho discute e revê a possibilidade de projetar aços contendo teores consideráveis de alumínio, e outros elementos de liga como Mn e C, através da termodinâmica computacional e bancos de dados comerciais. Como verificação preliminar, foram avaliados, experimentalmente, alguns equilíbrios e medidas de frações de fases em um aço experimental e os resultados obtidos foram comparados com os valores calculados e informações da literatura. Os resultados indicam que, para uma ampla faixa de composições os bancos de dados comerciais disponíveis parecem adequados ao projeto destas ligas.

Oct 30, 2017

By Aline Silva Magalhães

Nas últimas décadas a crescente demanda por carros mais seguros, econômicos e menos poluentes exigiram das montadoras, siderúrgicas e comunidade científica investimentos na pesquisa e no desenvolvimento de novos materiais, tais como os aços avançados de alta resistência. Dentro deste contexto, neste trabalho foi realizada a análise da microestrutura e das propriedades mecânicas de um aço bifásico na condição inicial e submetido a tratamentos térmicos com aquecimento na região intercrítica e resfriamento brusco. Foram analisadas a proporção dos constituintes na microestrutura e as propriedades mecânicas por meio de microscopia óptica e eletrônica de varredura, de difração de raios X, dureza e de tração. Observou-se, em geral, que o aumento da temperatura intercrítica levou a uma elevação da fração de martensita e, consequentemente, influenciou de forma a aumentar os valores de dureza, resistência mecânica e diminuir a ductilidade.

Aug 16, 2017

By Mariana Carla Mendes Rodrigues

Os aços ferramenta para trabalho a frio são utilizados em diversas aplicações em decorrência de propriedades como elevada estabilidade dimensional, alta resistência ao desgaste e elevada temperabilidade. Tais características estão diretamente associadas à microestrutura do material, isto é, à quantidade, à distribuição, ao tipo e à morfologia dos carbonetos presentes e à quantidade de martensita revenida e austenita retida. Neste contexto, no presente trabalho foram caracterizados mecanicamente e microestruturalmente quatro aços ferramenta para trabalho a frio empregados na fabricação de cilindros de laminação a frio. Para isso, amostras foram retiradas dos próprios cilindros e foram realizadas análises de dureza, microscopia óptica, microscopia eletrônica de varredura, espectroscopia por energia dispersiva e espectroscopia de emissão atômica por plasma. De acordo com resultados, uma comparação entre as propriedades dos aços foi conduzida visando concluir qual deles é o mais adequado para a referida aplicação.

Aug 16, 2017

By Charles O'Connor, Ben Tisa

International Training Resources is a company consisting of personnel with extensive law enforcement and military special operations experience, The staff members are qualified to train and certify, assist and advise law enforcement officers and agencies, at any level, in critical incident policy, procedures and tactical resolutions. Successful critical incident resolution is comprised of many elements of professional skills and personnel. (Command staff, negotiators, snipers, tactical teams, uniform patrol, K-9, bomb squad, etc.) Recently, tactical teams have been developing the capability for the use of explosive methods for rapid entry into crisis locations. This document ‘will briefly describe the environment, operational issues and courses of action associated with developing a complete tactical breaching program for utilization by SWAT teams in response to operational conditions in critical incident situations. This topic is being presented to the I.S.E.E. evaluators under “Interesting Blasting Projects” and “Public Relations” categories. Tactical operations differ significantly from traditional industry practices and we appreciate the opportunity to show the industry other professional applications of explosive materials and techniques. Presently, of the few schools from which law enforcement officers can receive training with explosive breaching methods, International Training Resources is the only company currently teaching and certifying officers which has received total endorsement by the California Peace Officer’s Standards and Training Commission (P.O.S.T.) and the state blaster’s licensing commission. We have pioneered the combining of law enforcement needs and blasting industry technology to train tactical officers, nationwide, in the mission essential skills necessary for explosive breaching.

Jan 1, 2000

By J. F. Myers, F. M. Lewis

DISCUSSION L. E. Djingheuzian (Canadian Dept. of Mines and Technical Surveys, Ottawa)—In their Summary the authors say: "Reconciling the grinding efficiency with good metallurgy is still a problem." In the discussion of the first paper8 in his reply to W. I. Garms, Mr. Myers states: "Our grinding process with smooth I-in. balls has reduced by nearly one half the metallic losses in the fine micron sizes of the tailing. This is simply because less of the fine micron sizes are produced. Since the + 65 mesh size is the same as formerly, a higher percentage of the intermediate sizes are developed. These sizes have the highest floatability, require the least reagents, and use less floating time. "These factors contribute so heavily to the overall economies that dropping our power grinding gain from 28 pct back to 19 pct is a small detail. However, we feel that this is only a momentary situation and that eventually the best features of the grinding and flotation processes can be brought together, which is as it should be." Italics are mine. The above statements, to me, appear to be the answer to the opening statement in the Summary. Denoting the costs at different power grinding gains as: Power Grinding Power Grinding Gain, 28 Pct Gala, 19 Pct Cost of grinding G G1 Cost of flotation F F1 Value of metallic losses T T1 where G1 > G2 F3 < F, and T1 < T, we have: G1+Fl+T1<G +F+T. Since the authors accept the idea that "grinding in flotation plants becomes part of the &apos;conditioning&apos; of the feed to flotation",4 i.e., that in flotation the ball mill is primarily a conditioning machine, it can be postulated that Tennessee Copper grinding at cost G1 is more efficient than grinding at lower cost G. This can be directly inferred from the Conclusion of the paper. Mr. Myers also emphasizes this at the end of his reply to Mr. Garms: "that grinding is for the purpose of preparing flotation feed and not grinding per se." This, to me, in the final analysis means that when the efficiency of grinding is weighted against the conditioning factor, the former becomes a function of efficient conditioning, hence, within the system in which proper conditioning is the dominant factor, the best grinding efficiency is provided by grinding which will contribute towards the optimum conditioning. This brings us again to the statement: "that if every grinding unit were considered as a conditioner for each following step, efficient grinding plants would become much easier to design."&apos; In other words, grinding equipment should be balanced against the flotation equipment and against chemical reactions taking place in the system. F. C. Bond (Allis-Chalmers Mfg. Co., Milwaukee)— The authors&apos; discussion of the probable ball motion in a slow speed high dilution mill is very interesting. When the 1-in. balls have worn down to about one fourth of their original weight they apparently first develop a flat surface; as wear progresses this flat face becomes concave, and other concave faces appear. It seems more probable that the first flat face may form at the softest part of the ball surface, and that each succeeding contact tends to force this flat face into sliding contact with a larger round ball; than that the flat faced ball tends to pair off with a particular round ball and to travel with it continuously. When the small worn ball has a flat face and is in sliding contact with a large round ball, the surrounding large balls will assume a more or less definite pattern, and slide against the worn ball, thus producing secondary concave faces. The primary concave face seems to be larger and better developed than the secondary faces. The ball charge can be divided into "concaves" which show at least one concave surface, "intermediates" which have developed flats or incipient concaves, and "rounds." Ball slippage is always present in a tumbling mill, and the mutual ball movement is necessarily a combination of rolling and sliding. The sliding motion is apparently concentrated upon the smaller worn balls which nest between the surrounding larger round balls. When each worn ball starts its upward path in the mill its primary flat or concave surface fits against a larger round ball, and the round ball slides upon it. The action may be something like that of the ball separator in a ball bearing, except that the worn sliding balls are always under considerable pressure. The material is ground under the combined influence of breakage 1—by impacts between falling balls and between falling and supported balls, 2—by being nipped between rolling balls, and 3—by being rubbed between the sliding balls. The rubbing action will be increased in the presence of worn balls with concave surfaces. The rubbing action probably produces a considerable portion of the finely ground slimes in the product. The worn balls commonly approach tetrahedrons in shape, and are very different from concavex, each of which has two equal opposed concave surfaces. Concavex were designed only to grind upon themselves, and not for use in combination with grinding balls. Their action in a grinding charge is very different from

Jan 1, 1952

By Alexandre Dolabella Resende

O estudo do padrão de fluxo do aço no molde de lingotamento contínuo é de grande importância para a siderurgia, uma vez que permite compreender como as variáveis de processo afetam a qualidade do aço produzido. Existem diversas técnicas, numéricas ou experimentais, utilizadas para realizar esses estudos. Este trabalho apresenta um estudo de simulação numérica, que tem como objetivo avaliar a influência da fração de argônio injetada no sistema no padrão de fluxo do aço no molde de lingotamento de placas. As condições de processo simuladas foram obtidas de diversas máquinas de lingotamento, com diferentes vazões de aço e argônio injetado. Os resultados numéricos foram validados através de um método experimental denominado “Nail Board”. Após a realização do estudo, foram constatadas consideráveis alterações do padrão de fluxo devido à variação da fração volumétrica do argônio injetado no sistema.

Aug 17, 2017

By W Valery, A Jankovic

The ball mill in closed circuit with hydrocyclones is an industry standard, and well known methodologies exist for equipment sizing, selection and design. However, the potential to improve the capacity of ball mill circuits by replacing cyclones with screens has been recognised for many years and recently has been successfully realised, thanks to developments in fine screening technology. Proper methodology for equipment sizing and selection is required to capitalise on this opportunity, but there is currently insufficient information and few guidelines available on how to design such a circuit. This paper discusses the differences between ball mill circuits closed with cyclones and with screens. A methodology is described for equipment sizing and selection for a circuit closed with screens, and the laboratory testing requirements are described for low grade base metal ores and magnetite ores. An economic evaluation is also presented for a case study demonstrating the potential benefits of closing a ball mill circuit with screens.CITATION:Jankovic, A and Valery, W, 2013. Energy efficient ball mill circuit - Equipment sizing considerations, in Proceedings MetPlant 2013 , pp 285-295 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By R. J. Chase, C. Davies

"Abstract- The Merelani graphite-tanzanite deposit is located in northeast Tanzania, 14 kilometers south of Kilirnajaro International Airport and in close proximity to the towns of Moshi and Arusha . The graphite mineralization is hosted by relatively undeformed linear Proterowic metasedimentary gneisses, several of which have been subjected to hydrothermal alteration resulting in tanzanite mineralization. Exploration work comprised detailed geological mapping coupled with pit and trench channel sampling and a subsequent 1500 meters of diamond drilling. In addition, metallurgical tests have shown the graphite to be of unusually coarse flake size, crystallinity and high purity.Feasibility studies have shown the economic viability of a major coarse flake graphite deposit with the measured resource to 50 meters in excess of 9 million tonnes assaying over 8o/o graphitic carbon . Production is due to start by the end of the first quarter of 1994 with the processing plant design capacity initially set at 15 000 tonnes per annum.ln addition to graphite production, tanzanite will be produced through selective mining within the graphite open pit in the upper horizon and from underground workings within the lower horizon.The Merelani graphite-tanzanite deposit will be the first major orebody to be exploited through means of private funding since Tanzania gained independence."

Jan 1, 1994

By Clarke P. E

At the end of the recent war, reports became available from Europe of the use of tungsten-carbide inserts in percussion rockdrill bits. These bits were used with small size rockdrills, so that the only advantage gained from the use of the harder, abrasion resistant, tungsten-carbide appears to have been the greater life of the bit. Larger machines, such as used in Australia in conventional practice, had to be discarded to protect the relatively brittle tungstencarbide inserts and the vulnerable bonding with the bit body.As it had been found in machine shop practice that some grades of tungsten-carbide had been produced with considerably improved toughness, it was decided by Gold Mines of Australia Ltd. that drilling practice with tungstencarbide bits warranted detailed examination under Australian conditions, and that drilling tests should be undertaken at Morning Star (G.M.A.) Mines N.L., for which it acts as General Manager and Consultant.These investigations progressed through three stages:1. Preliminary Investigations and Tests.When the investigations were initiated no commercial bits were available in Australia, and manufacture was commenced with improvised equipment from virtual scratch. These early tests indicated that the use of 3 in. bore rockdrills in conjunction with tungsten-carbide insert bits was a &apos;possibility, and that it was unlikely that a small bore...

Jan 1, 1950

By P. Umadevi

In the light of the discovery of the new super-conducting YBa2Cu3O7-x (YBCO), reactions in the Y2O3¬CuO-BaO system at 1300°C was investigated. The search was for any new phase that may be formed in the system at 1300°C (only 950°C reactions are known so far). 35 mixtures of different compositions were prepared and heated at 1300°C. No new phase was obtained. It was found that YBCO is decomposed at this temperature and Y2O3 and BaCO3 are the major components in the solid obtained after firing in air. However, on cooling the melt slowly and annealing at 950°C YBCO reforms. Such reactions on cooling might have implications on processing of the superconductor YBCO for practical applications as well as on its crystal growth by flux method.

Jan 1, 1989

By Taghi Sherizadeh, Kutay E. Karadeniz, Dogukan Guner, Samuel Nowak

Underground mining environments bring occupational health and safety issues with some severe dangers such as mine disasters like explosions. During such events, miners might escape using main access openings, or find a safe haven like refuge alternatives (RAs) to wait and be rescued and evacuated to the surface. In this paper, RAs are explained with their early and current applications. A classification as permanent and portable is explained depending on the conditions and their abilities. This classification is followed by the utilization and survivability of RAs with the requirements and recommendations of the main mining countries. Based on the utilization and survivability constraints, basic human requirements, waiting for a rescue team, and the required physical specifications of RAs during the events are analyzed in detail for various countries with their regulations. Among these, the specification, resistance to the explosion, is discussed in particular, and the studies in the literature are examined in terms of structural deformation. The highest deformed zones, the beneficiation of reinforcing steel components such as stiffeners, and the simulation approaches are investigated through this review.

Sep 24, 2022

By John McEwen, Ian R. Jonasson, David H. Watkinson

"Mine Gallen is a zinc-rich pyritic volcanogenic massive sulphide deposit that occurs in a fault-bounded block of intermediate volcanic rocks. The block is completely surrounded at the present erosion level by the eastern part of the Lac Dufault granodiorite. The volcanic succession includes a massive feldspar porphyry that is probably a subvolcanic intrusion, an andesitic flow unit and lapilli tuffs. The latter are variably sericitized and pyritic, especially in the vicinity of the massive sulphide into which they grade.The ore body is predominantly pyritewith local sphalerite contents as high as 20%; minor chalcopyrite and trace galena are disseminated, but are found mainly along late cleavage. Most ore is a breccia of massive to banded pyrite-sphalerite, veined by massive and complexly banded sulphides. These structures formed by repeated blocky jointing, cracking, sealing, healing and annealing as hydrothermal fluid repeatedly passed through a developing sulphide mound. The deposit is interpreted to have grown on the seafloor in a manner similar to active mounds in the Galapagos rift.RESUME La Mine Gallen exploite un gisement de sulfures massifs volcan géniques comprenant essentiellement de la pyrite riche en zinc. Ce gisement se trouve a /'intérieur d’un bloc de roches volcaniques de caractère dacitique a andésitique, limite par failles et entoure de tout cote par la granodiorite du Lac Dufault. La séquence volcanique comprend des coulées andésitiques et des tufs à lapilli ainsi qu'un porphyre feldspathique massif sub-volcanique. Les tufs sont sericitises et pyritises, tout particulièrement au voisinage des sulfures massifs."

Jan 1, 1990

By David Norval

Ni, Co, Cu and Pt, mattes are common materials that require granulating and milling of the resultant granules for further processing. This route is acceptable if the material is brittle (friable) which is a property associated with the higher sulphur mattes. For lower sulphur levels, where the matte is less amenable to milling, the costs of the milling increases. This paper will compare water granulation with certain dry granulation processes and the downstream processes required for Hydrometallurgy. It will further introduce and expand on atomisation which offers a further safety benefit in the control of the metal flow into the &apos;wet zone&apos; with the use of a tundish flow control also reducing the conversion from the matte to powder in one fairly straightforward operation.

Jan 1, 2006

By Matthew Janes

Quality control procedures are increasingly important with today&apos;s higher capacity foundations and complex loading conditions. The need for a mobile, repeatable, nondestructive and economical load test method led to the development of an entirely new approach. The system described involves using solid propellant fuels to accelerate a reaction mass off the test pile. The force required to accelerate the reaction mass upward acts equally downward on the pile. Very high forces may be applied to the pile in a controlled, linearly increasing manner. The duration of the applied load is approximately 100 milliseconds. This rate of loading is slow enough to allow the pile and soil to react together as a composite rigid body. Pile/soil accelerations and velocities are low, typically 1 g and 1 m/s respectively. The effects combine to produce pile and soil response no longer dominated by the transfer of force via stress pulse (as with impact). Instead the pile force increases throughout the length of the pile, with pile top and toe stresses building in unison with time. This emulates the stress condition during static pile loading. Finally, state of the art instrumentation systems are used to obtain test data. Displacement is monitored directly using a laser datum and integrated receiver located at the centre axis of the pile. Force is also monitored directly using a calibrated load cell. Data is acquired and digitized using a 386 PC with user friendly software capable of producing load deflection curves and time histories in the field seconds after testing.

Jan 1, 1990