Search Documents

By D Johansson, C Yi

Blasting techniques are widely used to fragment rock masses into smaller pieces. Numerical modelling is an efficient method employed by many researchers in the blasting field. It is difficult for a conventional continuum-based approach such as the finite element method (FEM) to model the rock fragmentation by blasting and the expansion work on the rock by explosive and its detonation products. In this paper, the particle blast method (PBM) was employed to model the behaviour of the detonation and a bonded particle model (BPM) was used to model the brittle material to be blasted. A mortar cylinder with a centrally placed hole for the explosive was modelled and the results were compared to the experimental data. The blast process from crack initiation to fragment formation was analysed. The influence of coupling ratio on fragmentation was also investigated.CITATION:Yi, C and Johansson, D, 2015. Discrete element modelling of blast fragmentation of a mortar cylinder, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 793–798 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By E. S. Schubert

Keywords: co-generation, furnace CO-gas cleaning, disintegrator scrubber, Theisen In a closed, electric, reduction furnace, no oxygen enters the furnace from the surrounding environment. The off-gases are thus not ?burnt? and therefore contain a considerable amount of CO and H2. Traditionally these gases have been captured and burnt in a flare stack. Recent developments have led operators of such furnaces to revise this strategy and to consider utilising these gases as a fuel for gas-fired generator sets to produce electricity, thus becoming more energy efficient. On 31 March 2010 the new emission standards, in accordance with the Air Quality Act, Act 39 of 2004, were promulgated. The minimum emission standards according to the act require that the particulate matter emissions from the primary fume-capture systems on closed furnaces for ?new plants? in ferroalloy and calcium carbide production not exceed 50 mg/Nm³ and 25 mg/Nm³, respectively. By implementing co-generation, the producer automatically complies with the new environmental emission standards for an off-gas. As much as 30% of the electrical power cost, which is set to double in the near future, can be saved by partly generating one?s own electrical power. In December 2010, the National Treasury published a discussion paper for public comment, one entitled ?Reducing greenhouse gas emissions: The carbon tax option?. Irrespective of how the tax is finally implemented, it will result in an increase of production costs in affected industries. This paper focuses on the characteristics of a furnace-off-gas cleaning system for closed ferroalloy smelters, characteristics that meet the requirements of both reducing solid-matter emissions and operating a safe and reliable gas plant.

Jan 1, 2011

By Teruhisa HORITA

The durability of SOFCs is one of the critical issues to realize the SOFC systems. In order to improve the durability, a precise degradation mechanism should be clarified at the different functional ceramic interfaces in SOFC cells and stacks. This paper reviews the improvement of SOFC durability by the mass transport analysis especially at cathode/interlayer/electrolyte interfaces. We have made a precise analysis on the reaction of cathode with impurities. Especially at the (La,Sr)(Co,Fe)O3/CeO2/ZrO2 interfaces, a significant amount of SrCrO4 and SrSO4 were observed at the (La,Sr)(Co,Fe)O3 surface as well as inside the (La,Sr)(Co,Fe)O3 cathode, which suggested some process occurred for both poisoning. Possible degradation mechanisms were proposed based on the observation data.

Jan 1, 2016

Changes in reductant and energy inputs which are required to adjust the slag composition in anilmenite smelter to a higher or lower FeO content are calculated. The calculated changes are based on the assumption that solidification equilibrium with the freeze lining constrains the slag composition to follow a eutectic groove in the TiO2-FeO-TiO1.5phase diagram. Calculated equilibrium conditions along the eutectic groove are presented, and form the basis of the calculations. The inputs of energy and carbon need to deviate strongly from the steady-state values to adjust the slag composition. The inputs required at any given time depend on the desired rate of change of the slag composition, and the current slag composition. The steady-state relationship of a change in energy input of 5 kWh corresponding to a 1 kg change in carbon input does also hold for the changed inputs during transient changes in FeO content. Keywords: Ilmenite smelting, freeze lining, solidification, eutectic

Jan 1, 2003

By G. Donald Emigh

Nothing is more important to life-plant and animal-than phosphate. Its compounds are essential to the energy functions of all living systems and for the formation of bones and teeth. Animals get their phosphate from eating plants and other animals, or domestically from feed supplements. Plants get their phosphate from the soil. Man's most important use of phosphate is for fertilizer; however, he is also a heavy user of many industrial phosphate chemicals. Phosphate occurs in all igneous and sedimentary rocks, and in all fresh and saltwater. The average content in rocks is 0.1 to 0.2% P2O5, as documented recently by McKelvey (1973). About 200 minerals contain more than 1 % P,O,. However, the important one in igneous rocks is fluorapatite, (Ca,(PO,) ,F) containing about 42% P,O, and 3.8% F,; in sedimentary rocks the one important mineral is francolite, a carbonate fluorapatite containing up to 2% molecular CO,. Both are in the apatite family of minerals. The mineralogy of phosphate minerals was reviewed recently by Altschuler (1973). Although phosphate occurs in nearly all rocks, economic recovery is limited to deposits where natural concentration of the phosphate mineral has occurred. Occasionally natural concentration is great enough that the material can be used as mined; generally, however, the ore is low grade and must be concentrated.

Jan 1, 1975

By Steven J. Page, John A. Organiscak

The amount of airborne respirable dust generated from break- age of different coals varies widely. This research was conducted to identify the facets of airborne respirable dust liberation from the coal product. Laboratory crushing experiments were conducted on a range of low to high volatile bituminous coals to investigate the various factors influencing airborne respirable dust generation. Bituminous coal samples from 8 mines (5 U.S. and 3 Polish) were uniformly prepared and processed through a double roll crusher located in a low air velocity wind tunnel. Experimental factors studied included inherent coal seam constituents, specific energy of crushing, product size characteristics, dust cloud electrostatic field, and specific quantity of airborne respirable dust generated. The results of this investigation build upon previously published results, which indicated that a combination of several factors are associated with the generation of airborne respirable dust. One factor involved is the effect of coal rank, described by the inherent moist fuel ratio, on the product size characteristics, defined by Schuhmann size function parameters. However, since coals of high moist fuel ratio (high rank) are generally more extensively cleated, it is suggested in the present work that the degree of cleating is directly responsible for the quantity of respirable-sized particles produced in the crushed product material for eastern U.S. coals. This is implied by the relationship of ash content and at least one mineral constituent (pyrite, determined from pyritic sulfur analysis) to the percentage of airborne respirable dust. To validate this hypothesis, a description is offered that is based on known coal petrography. Another key factor is the effect of air dry loss moisture in the coal seam on the breakage-induced electrostatic field of airborne dust. The air dry loss moisture factor appears to control the amount of airborne respirable dust that is liberated from the product. The resultant effect of these factors is that different percentages of coal particles smaller than 10 µm are dispersed as airborne respirable dust with a well-defined peak in the normalized airborne respirable dust for a narrow range of air dry loss moisture - ash ratios. A clear delineation of coals, based on well-known proximate analysis characteristics, that generate the most respirable dust appears to be possible. It was also shown that the dust-generating characteristics of coals could be reasonably described by both the moist fuel ratio

By Nelver Benavides

"Actualmente en la industria minera, las técnicas de control avanzado, la integración de procesos y tecnologías ya no son consideradas como conceptos exóticos y de dudoso impacto productivo, sino solo como un eslabón más en el proceso de mejora continua. En ese sentido, el presente texto señala la integración de estas tecnologías en la Concentradora Cuajone – Southern Perú, considerando las operaciones de chancado, molienda, sistemas de recuperación de agua y proyectando expectativas a mediano plazo para las operaciones de flotación, extracción y voladura. "

Sep 12, 2011

Factors of importance in the ntilization of coal fines are mentioned, and the results of flotation tests on coal fines from three important coal seams in New South Wales are presented.INTRODUCTIONEconomic utilization of fine coal is an important problem in the Australian coal industry, particularly as the proportion of fines mined is increasing with progressive mechanization.While the use of uncleaned coal fines may be economic, it may be preferable to beneficiate them, but the most economic process must be selected.For beneficiating coal finer than about 28 mesh, froth flotation can be applied, but mining engineers should avoid practices that may be detrimental to flotation. Such practices include the indiscriminate use of water, particularly that containing a wetting' agent, for dust suppression. In addition, clay stemming in wet conditions may produce slimes which could adsorb on coal surfaces, while the use of oils and greases as well as the application of stone dust and chlorides in roadway consolidation may influence adversely fine coal beneficiation.This paper deals with the application of flotation to samples of fine coal from the Bulli, Greta, and Victoria Tunnel seams. In addition a discussion is given of the mineralogical constitution, size analysis, and degree of liberation of ash constituents of the various samples.COAL SAMPLESRepresentative samples of coal from the Bulli, Greta, and Victoria Tunnel seams were obtained for testing.

Jan 1, 1961

By Daniel Rodrigo Leiva, Rogério Felito da Silva, Bráulio Salumão de Oliveira

Os aços de baixa densidade e os de alto módulo elástico visam a manufatura de automóveis com menor peso e possuem interesse crescente por parte de indústrias e centros de pesquisa. Documentos de patente são uma fonte de informação essencial para análise do desenvolvimento de um setor tecnológico, além de fundamentar tomada de decisões. Este trabalho objetivou elaborar e analisar indicadores, baseados em informações contidas em registros de patentes, em aços de baixa densidade e aços de alto módulo elástico. Diversos elementos de liga e reforços foram mapeados para o aumento da resistência específica e controle de microestrutura, principalmente para aplicações na indústria automobilística. Ambas as tecnologias apresentam interesse recente e se encontram em um estágio emergente de desenvolvimento. As propriedades de ductilidade, resistência a tração e ao impacto figuram entre seus principais desafios tecnológicos, assim como a redução de custos.

Mar 1, 2019

By D. Eastick, S. Hardcastle

"Over the last few years, a multi-faceted feasibility study has been evaluating the introduction of hydrogen fuel cell-powered equipment into underground mines to replaced diesel engine-powered equipment. The analysis has shown that under normal operating conditions fuel cells could at the very least be an environmental and health benefit by eliminating combustion engines and their unwanted by-products. However, they could also generate significant reductions in the amount of ventilation a mine needs to supply when compared to dieselized operations; this would further decrease a mine’s energy consumption, its associated greenhouse gas impact, and also reduce a mine’s significant ventilation-associated costs. Fuel cell-powered equipment also has the advantage of lower noise and heat production compared to its equivalent diesel-powered counterpart.The degree to which fuel cells can generate ventilation benefits in underground mines depends upon a number of operational parameters and mine specific qualifiers such as current ventilation control or management, mine depth, inherent dust conditions, and minimum velocity requirements.However, another major consideration in the introduction of fuel cells in underground mines will be the safety requirements associated with diluting and removing the potentially explosive hydrogen in the event of a gas leak. In outside surface applications, it is possible to use dispersion, buoyancy, time, and lack of ignition sources as mitigating factors in deriving a low risk of an explosion. However, in underground operations, these factors change, and dispersion and buoyancy are limited; time may not be available and, in non-coal mines, ignition sources are not typically controlled. When a hydrogen leak occurs, the availability of sufficient ventilation to dilute and effectively remove the gas will be critical. Consequently, ventilation may be the prime risk controlling factor. In this paper, the authors evaluate the potential benefits of replacing diesel engines with fuel cells in powered production equipment, discuss the mitigating qualifiers that could limit ventilation savings, and evaluate solutions to retain and maintain an additional ventilation capacity in the event of an emergency situation, such as a hydrogen leak from the fuel cell stack or its distribution system."

Jan 1, 2007

On the Role of Dixanthogen in Froth Flotation

Sep 13, 2010

By Dennis R. Dolinar, John L. Ellenberger, Gabriel S. Esterhuizen, Anthony T. Iannacchione

A survey of pillar conditions was carried out at 21 operating limestone mines that use the room-and-pillar method. The surveyed pillars were all located in rock that was classified as “Good” to “Very Good” using the RMR rock mass classification system. The average pillar width was 14.5m and the width to height ratio varied between 0.53 and 3.52. Pillar conditions were rated using a visual rating system that accounts for the effect of geological structures as well as stress related fracturing. Nine cases of pillar instability were recorded. Pillar instabilities were typically limited to individual pillars or small groups of pillars within an otherwise stable layout. Local geological structures such as inclined discontinuities or weak bedding planes contributed to instability in seven of nine cases that were observed. Elevated pillar stresses contributed to instability in the two remaining cases. All the unstable pillars observed had width-to-height ratios of less than 1.5. It is concluded that pillar instability is most likely to be caused by unfavorable geological structures in pillars with width to height ratios of less than 1.5. Stress related instability such as rib spalling becomes more prevalent when the average pillar stress approaches approximately 20 MPa.

By Israel Liebman

The Bureau of Mines conducted an investigation to determine those factors that are significant in affecting the velocity of flames propagating along the boundary separating gaseous fuel and air. In addition the aerodynamic motion of the gases in the vicinity of such interfacial flames was delineated. Parameters in the study included flammable zone thickness, flammable zone concentration of gradient, fuel type, and position of the flame relative to various environmental surfaces. Of all these factors, the flammable zone thickness and burning velocity of the stoichiometric mixture were found to have the most significant effect on the flame speed. Notion of the gases in the vicinity of the interfacial flames was examined by particle track and interferometric techniques. The relative velocity of the interfacial flame with respect to the unburned gas on the central streamline was found to equal the burning velocity of a stoichiometric homogeneous fuel-air mixture. In addition, it was observed that the composition of the lean fuel-air mixture at the boundary of the combustion zone appears to be less than that defined as the fuel's lower flammable limit.

Jan 1, 1968

By J. C. Wynn

J.R. Hillebrand From the abstract, "A realistic ore deposition model to serve as a conceptual framework." Further, on page 246, "The first area of study was the Josephine peridotite, now identified as an ophiolite terrane, located in northern California and south-western Oregon (Fig. 3). Here, it was felt that we could test the models shown in Figs. 1 and 2 and, if successful, expand the model and test it in other chromite districts in the US and around the world." My comments refer only to chromite deposits in Europe and the Middle East. First, I question that may chromite deposits occur in the idealized ophiolite section shown in Fig. 1. Second, although some podiform deposits (referring to morphology) have been important (Guleman, Turkey, for example), the stratiform deposits are of greater importance in tonnage and frequently grade. Examples include Nada, Yugoslavia; Bulqiza, Albania; Xerolivado, Greece; Saranovsk, Russia; and Abdasht, Iran. Reply by J.C. Wynn Mr. Hillebrand raises two issues that deserve a serious response. One issue is basically subjective and the other is ultimately political. First, the question of where (and how many) podiform chromite deposits are found in the idealized ophiolite section of Dickey (1975). The Dickey model is still perhaps somewhat controversial (Panayoutou, 1980), but our experience in the Josephine ophiolite of northern California (Wynn, 1980; and Albers, 1983) shows that the model works well there. Virtually all the chromite is found in dunite lenses in the tectonite peridotite (harzburgite). Since there are few complete ophiolites exposed in the world, the model will probably never satisfy everyone. The degree of acceptance is a function of any individual's subjective experience. Second, it is well known that stratiform chromite contributes more than 95% of the chromite reserves presently known in the world, and it could be reasonably argued that there is no point in exploring for or exploiting podiform deposits further. The title of the paper, however, was in part 'strategic minerals geophysical research'; chromite is considered a strategic and critical mineral of the US and many other industrialized nations. Stratiform deposits in South Africa and Zimbabwe account for most of the chromite reserves in the world. Unfortunately, experience in modern times with substantial price fluctuations and even resource cartels dictates the wisdom of identifying and maintaining a national chromite reserve, irrespective of the cost. An improved exploration methodology is an essential element in this strategic objective. References Albers, J.P., 1983, "Geological and Geophysical Studies of Chromite Deposits in the Josephine peridotite, California and Oregon," US Geological Survey Bulletin 1546 A-D, 118 pp. Dickey, J.S. Jr., 1975, "A Hypothesis of Origin for Podiform Chromite Deposits," Geochimica et Cosmochimica Acta, Vol. 39, pp. 1061.1074. Panayiotou, 1980, Proceedings, International Ophiolite Symposium, Cyprus, 1979, 781 pp. Wynn, J.C., 1980, "Exploration Geophysical Methods and Strategies, and Their use to Locate and Assess Small Mineral Deposits," Chapter 12 of Meyer and Carmen, eds., The Future of Small Scale Mining, McGraw-Hill, New York, pp. 75-83.

Jan 12, 1983

By Lu Lin, Yanping Bao, Xiang Li, Linzhu Wang, Xiaobai Yan

The results showed the microinclusions were mainly Al2O3 and sulfide inclusions from tapping to the beginning of LF refining. Al2O3 inclusions were modificated into calcium aluminates after calcium treatment. Lots of spherical calcium aluminates composite inclusions containing MgO, TiO2 and MnS were found after soft blowing and during tundish metallurgy and left in the slab which caused the defects of beam plates. Pure Al2O3 inclusions were observed again after soft blowing 8min. Average sulfur content in inclusions decreased because of the high desulfurization ability of refining slag. Average Ca/Al ratio value in inclusions increased during LF refinging because of the reduction of CaO in slag by carbon and it increased obviously during the process of soft blowing 8min because of the dissolusion of calcium wire.

Jan 1, 2015

Hydrogen and carbon monoxide reduction data were obtained on pelletized materials of the type currently being prepared commercially in Australia.Pellets, approximately 1 cm diameter, made from Deepdale, Iron Prince, and Mt. Newman iron ore were reduced by hydrogen over the temperature range 500°-900°C and the reduced pellets were examined by thermogravimetric, microscopic, electron probe, and x-ray techniques. After an initial time delay it was found that up to 95 per cent reduction the data could be described by a porous model where gaseous diffusion through the solid is rate controlling. Independent measurements of effective diffusivity supported the values obtained from the reduction data. Above 95 per cent reduction the rate decreased markedly due to the formation of retained wustite or fayalite.Comparison with reduction by carbon monoxide over the temperature range 750°-900°C showed that the rate of reduction was approximately five times slower than for reduction by hydrogen.The rate of reduction was found to be a function of the initial properties of the pellets which may account for the widely conflicting results that have been obtained with previous investigations on porous pellets.

Jan 1, 1971

By Margaret R. Egan

The Bureau of Mines experimentally burned Pittsburgh Seam coal and other combustible materials found in mines in order to obtain a better knowledge of their emission products. These experiments were conducted in the Bureau's intermediate-scale fire tunnel, which simulates environ-mental conditions in underground mines. Smoke characteristics, gas concentrations, mass loss, and ventilation were measured. From these values, heat-release rates, particle sizes, obscuration rates, combustion yields, and production constants were calculated. This information was sought as part of a comprehensive study of combustible materials that will ultimately advance the design of more efficient fire detection and suppression systems. The coal combustion measurements presented in this report, together with previous analyses of wood and transformer fluid fires form a data base by which future studies of other mine combustibles can be compared.

Jan 1, 1987

By Bellairs P, Stewart JC

On 20 December 1983 at 8.40am blast- hole 57 of Blast RN177 prematurely detonated follwed by a violent deflagration of blast- hole 59 at 10.40am. The blastholes were 380mm diameter drilled in black pyritic Mt McRae shale. The blastholes were loaded with ANFO and primed. Blasthole 57 was stemmed and blasthole 59 was not. A poss- ible mechanism which could lead to such a detonation is described. preliminary tests showed the top 5m of a bench had the highest temperature which could not be influenced by a range of treat -ments. Small scale laboratory tests show- ed that zinc oxide (ZnO) and magnesium carbonate (Mg2CO3) inhibited the reaction. A series of tests using AN with and without inhibitors loaded into the collars of blast -holes drilled in the top 6m of the bench and unstemmed is described. An analysis of the time to reaction of the holes loaded with AN against temperature shows that the decomposition of the AN in contact with the black pyritic shale is probably a sulphuric acid catalysed react- ion. All the inhibitors tested can neut- ralise the sulphuric acid in the shale. 10% ZnO appears to be an effective inhibitor of the reaction providing the AN/ZnO (90/10) is kept out of contact with surface material whose temperature can be as high as 60¦C in summer. It is concluded that ANFO/ZnO (90/ 10) should be now tested in stemmed holes.

Jan 1, 1986

By K. Ward

The Environmental Protection Agency (EPA) is beginning to provide compliance assistance visits to various industries, including mining, for Emergency Planning and Community Right-to-Know Act (EPCRA) compliance. The EPA inspectors may consist of a multi-media team deployed to review systems and procedures for EPCRA Sections 302, 304, 311, and 312. The Team’s focus may include emergency response plans, training programs, qualifications of personnel, and release notification protocols. This presentation takes a look at the EPCRA compliance challenges faced by Arizona copper mining and processing facilities.

Jan 1, 2001

By C. D. Hebert, M. R. King

The 56,000' (17 km) long San Vicente Aqueduct Pipeline tunnel is being constructed using precast concrete rings to act as preliminary ground support through two sections of the bored tunnel with lengths of 9,450' (2.9 km) and 33,700' (10.27 km).The six segment bolted trapezoidal ring was manufactured using a combination of steel fiber reinforced concrete and self compacting concrete in vertical moulds. This paper briefly describes the design and function of the segments, and reviews the development stages of the concrete mix, and the advantages and disadvantages of the adopted manufacturing method.

Jan 1, 2007