Search Documents

By Gavin J. Faulkner

This paper presents an investigation of some alternatives, and improvements to timber posts and cribs. The purpose is to find a cheaper, better, easy to install, and effective means to replace or improve them. Selection of supports needs to take account of several factors. These factors include the mechanical behavior of the support, technical feasibility, and cost. In this paper a variety of supports are compared on these bases. Particular advantages and disadvantages of those supports have been determined through published material and a testing program. A broad evaluation of a number of specific groups of supports is presented. Included in this evaluation are timber posts and cribs, steel friction props and several, newer developments such as the Micon Yield Capsule and the Super Post. Another support that will be briefly discussed is steel-fiber-reinforced concrete. Particular emphasis will be placed on the Micon Yield Capsule and the Super Posts on which preliminary testing has been carried out. The testing results are presented in detail. The shortcomings of the test procedure are pointed out and some new ideas to improve the testing in the future are proposed.

Jan 1, 1986

By Bisweswar Das, Barada Mishra, Hrushikesh Sahoo, Swagat Rath

Banded hematite jasper (BHJ) containing 45.2% Fe, 32.64% SiO2, 0.63 % Al2O3 and 1.25 % LOI is found difficult to beneficiate either by magnetic or flotation techniques due to fine intergrowth of jasper with hematite. Phase transformation by reduction roasting with activated charcoal followed by low intensity magnetic separation to achieve a suitable iron concentrate has been attempted in this study. The mineralogy of the ore and different roasted products has been studied by X-ray powder diffraction (XRD) and scanning electron microscope (SEM) to understand the reduction mechanism. The magnetite formation is observed at 850ºC while metallic iron appeared at a higher temperature. The effects of reduction variables such as reduction time (30-270 min), temperature (750-1050ºC), and reductant (1-12 %) using activated charcoal are studied. An iron concentrate with 64.65% Fe and 55.8% recovery could be obtained under optimum conditions of temperature: 850ºC, time: 1.5 h, and reductant: 6% by weight.

Jan 1, 2014

By G. F. Livingston, F. K. Shelton, J. C. Stahl, R. E. Churchward

"INTRODUCTION An investigation of the metallurgy of cobalt from domestic ores has been in progress since February 1940 and has resulted in the formation of a hydrometallurgleal process for the production of electrolytic cobalt metal. Previous reports of these investigations have been given by F. K. Shelton; 7/ and Ruth E. Churchwrd, F. K. Shelton, and G. Knickerbocker. 8/ Briefly, the process, as applied to ores containing cobalt oxide, consists of leaching with H2SO3 or, preferably, with H2SO3 and H2SO4, to dissolve the cobalt. The cobalt solution passes through one or more purification stages to remove iron and elements of the copper group, and cobalt carbonate is precipitated under carefully controlled pH conditions. The cobalt carbonate is dissolved in on acid electrolyte containing sulfuric acid, boric acid, and sodium fluoride. The electrolyte then proceeds to electrolytic cells where cobalt is plated as a metal and sulfuric acid is regenerated.The present paper contains the results of several investigations signed to give a more complete chemical and engineering understanding of different unit processes involved in the electrowinning of colbat. Some work has been done to broaden the process to include arseniferrous cobalt ores as well as the oxide ores upon which the investigation was initiated. Most of the data presented herein have been obtained since the release of the previous reports; any changes suggested heroin that conflict with recommendations in earlier reports are based on more complete data and usually are preferable."

Nov 1, 1945

The limit of pressure to which an underground dam may with safety be subjected, is a question that-as far as the writer knows has not received the same attention from authorities on engineering construction, or practical mining, that has been accorded to questions on which the design and strength of other structures or machines in connection with a mine are based. That dams may, under certain conditions, be constructed to resist water under great pressure is a known fact. But the difficulty of demonstrating beforehand that any proposed structure of this kind will withstand the pressure and be effective is, owing to the indeterminate nature of some of the risks to be provided against, very great. In the present state of our knowledge it may almost be laid down as a rule, that a dam of this kind should not be undertaken where grave consequences would attend failure until experience of structures where the physical conditions are similar, but where there are no such risks, has given assurance that such work would stand.In Mines and Minerals for May, 1900, there is published a paper by Mr. James McNaughton describing the construction of three underground dams in the iron mining district of Michigan.The first of these was put in to hold back a flow of 750 gallons per minute, which when pent up created a pressure of 276 pounds per square inch, showing that the height of the sustained column was about 635 ·feet. The hole through which the water issued was in the bottom of the cross cut it was enlarged by removing all loose rock for a depth of 18 ft...

Jan 1, 1901

By Cadman S. J

( The central part of the Gippsland Basin is surrounded by existing major Petroleum accumulations and although six exploration wells have been drilled in the area, none are significant petroleum discoveries. Post drilling analyses indicate that the wells were drilled off structure due to the presence of high-velocity Miocene channels. These channels contain carbonates of significantly higher interval velocity than the surrounding sediments. Problems with seismic interpretation were thus encountered in the development of prospects in the central part of the Gippsland Basin as part of a BMR prospectivity study. The seismic interpretation problems associated with the Miocene channels are two-way time pull-ups at the underlying top of Latrobe Group and deeper levels on the seismic sections. Interpreted seismic sections passing through some of the exploration wells and the Miocene channels are presented to illustrate the configurations of these channels and the pullup effect associated with them. Two different methods of depth conversion were applied, one for the area below the high velocity channels and the other for the area away from the channel. The application of these two methods of depth conversion were found to be reasonably successful in correcting for the pull-ups caused by the high velocity Miocene channels. Mapping of the events near the top of Latrobe Group and near Base Lower L balmei seismic horizons has led to the identification of several potential structural closures. Further exploration efforts are necessary in this area to test these closures.

Jan 1, 1992

By Jean-Jacques Bouillon, Michel Jébrak, Stephane Faure

"Le gisement polymétallique (Cu-Zn-Au-Ag) des Mines Selbaie est forme par un réseau de filons encaisses dans une séquence de pyroclastites felsiques du sill on Harricana-Turgeon. Les minéralisations sont encaissées dans le tuf de Selbaie, situe sous une épaisse séquence d'ignimbrites Iitées. Ce gisement se distingue des autres gites archéens par une chronologie atypique des minéralisations: les veines de chalcopyrite, de sphalérite et de galène recoupent un amas exhalatifpyriteux stérile. Un vaste halo d'altération hydrothermale a chlorite et mica blanc est associe à cette minéralisation.La mise en place des veines minéralisées est associée à une phase d'extension NNW-SSE. Le complexe volcanique subit, par la suite, trois phases de déformation. Une compression, orienté N-S, développe une schistosité à peine pénétrative et un réseau de fentes de tension. Une réorientation des contraintes locales selon une direction WNW-ESE conduit au chevauchement de I' écaille d'andésite et de tonalite de Brouillan. Un réseau conjugue de failles normales cassantes est associe au relâchement des contraintes."

Jan 1, 1990

By S. K. Sharma, R. Markandeya, G. Venkateswara

"In this study, a three level Box- Behnken factorial design combined with Response surface methodology (RSM) for modeling of process parameters of Multi Gravity Separator (MGS) for recovery Iron values from sub grade iron ore, Deposit No. 5, Bailadila complex has been developed. The three significant operational parameters of MGS, Drum rotational speed (RPM), Drum inclination (degrees) and quantity of wash water (LPM) were considered in the experimental work. Other parameters like feed percent solids, shake frequency and shake amplitude were maintained constant. The ‘as received’ sub grade iron ore sample is admixture of lump and fines and chemically assayed 40.80% Fe, 40.90% SiO2, 0.24% Al2O3 and 0.22% Loss on Ignition (LOI). The obtained results were evaluated with the Box-Behnken factorial design, RSM and also Quadratic programming(QP). Second order response functions were produced for Fe in terms of grade (%) and recovery (%) of the concentrate fraction. Taking advantage of QP, it was observed that maximum grade of 62.21% Fe achieved at an inclination of 4.3degrees, 2.7LPM of wash water and at a drum speed of 198 RPM. Similarly a maximum Fe recovery of 65.37% weight can be achieved at 4.3degrees inclination, 2.6LPM wash water and at a rotational speed of 212 RPM Predicted values of responses obtained using model equations were in good agreement with the experimental values. The influence of the process variables of the multi gravity separator concentrator on grade and recovery of concentrate fraction were presented and discussed."

Jan 1, 2014

By J. K. Whyatt

The paper presents an approach to design a multi level room and pillar layout in a 40m thick seam overlain by a major aquifer. The design was required to maximise extraction with due consideration of the general stability of the workings, the potential water hazards, and spontaneous combustion risks due to air leakage between horizons. The approach utilised was a combination of empirical pillar sizing for water hazard control with numerical modelling to assess potential interactions between horizons. The numerical modelling allowed the size of interleaves, and the appropriate staggers to be optimised in terms of stress distribution. The stress distribution allows both the general stability of the openings and more importantly the permeability changes around the openings to be determined. The permeability of coal is sensitive to stress, and an empirical stress to permeability relationship, and theoretical permeability to flow leakage relationship has been applied to interpreting the relative spontaneous combustion risk associated with each of the proposed layouts. The final proposed design is a compromise between maximum exploitation of reserves and consideration of water hazards and of spontaneous combustion risk. Further more detailed design will be required as more comprehensive data on the geotechnical properties of the coal and overburden become available.

Jan 1, 1996

By W. A. Backofen, D. Lee

Tlze condition of superplasticity or neck-resistanl flow that results front high strain-rate sensitivity has been observed in isothermal tension tests on several titanium alloys and one of zirconium hi general, il was associated with reasonably fine-grain micro-structures being stvained in the transformation range at rates below i - 10 -3 sec-&apos;. The metallographic mean-free path, L, was measured at room temperature after rapid cooling from the temperature of test-ing. The flow stress of Ti-GAL-4V at 950°C was proportional to La at different constanl <; the value of a decreased with increasing. E but at E< 1.5 x 10-4 sec-1 it varied only from 0.9 to 1.25. The findings were interpreted to mean that viscous boundary shear is the rate-controlling process of deformation at high levels of strain rate sensitivity in these materials. Elongation of over 1000 pet could be obtained, but a1 temperatures so high and rates so low that any practical application of the full effect would probably be difficult. As the transformation range was narrowed, by turning from Ti-6AL-4V to Ti-5Al-2.5sn to nomznally pure titanium, the allowable temperature varialion was correspondingly reduced. Superplasticily was not found in Armco iron, presumably because the transformation range was too narrow to allow the developtnenl of a reasonably stable microstructure for isolhermal lesting. THE work represented by this paper grew out of a recent study of texture hardening in a(hcp) titanium and zirconium-alloy sheet,&apos; of which part has now been published.2 It was found that, with heating, the tensile plastic-anisotropy index, R,* was decreased from well above 1 towards 1 as the temperature range for the a(hcp) -ß(bcc) phase change was entered. The clearest example of that trend is illustrated with previously unpublished data in Fig. 1. It might have been thought that such a development resulted simply from introduction of the cubic and therefore plastically less anisotropic phase. However, the accompanying change in the index of tensile strain-rate sensitivity, m = a log a/a log E, was rapidly upwards, to a high of 0.85 in some cases (also illustrated in Fig. 1). At the same time, the total tensile elongation rose to a maximum and the flow strength dropped away as R (and m) approached 1. Taken together, the observations cannot be understood as resulting from the presence of cubic phase, per se. It has been concluded instead that they reflect the largely noncrystallographic deformation which characterizes superplasticity. As demonstrated in other recent work? a necessary condition for super-plasticity is strain-rate sensitivity of flow stress sufficiently high that m is above a lower limit of -0.3. The origin of large m has been traced, in turn, to grain size so small that a substantial amount of viscous deformation is introduced by such processes as Nabarro-Herring diffusional flow4 and/or grain boundary shear.5,6 Because of problems in the processing of titanium and zirconium alloys—problems of high strength, limited ductility, and excessive springback, originating largely in slip resistance-it was natural to wonder if something useful might be done with superplasticity in those materials. Therefore experiments were made for more closely identifying and generally bounding the phenomenon with temperature and strain-rate limits, before attempting to decide about its exploitation. The results are being reported here. EXPERIMENTAL Materials. The two of primary interest were the titanium alloys of nominal composition (in wt pct) 5A1-2.5Sn and 6A1-4V. Others were a 4A1-1/4O2 titanium alloy, titanium of commercial purity (RC-70), Zircaloy-4. and Armco iron. All were received as annealed 3/16 in. thick sheet, except RC-70 which was & in. thick, and tested in that condition. Details of transformation temperature and grain size are given in Table I. The results of dilatometry for the measurement of transformation temperatures were unsatisfactory. Data were finally obtained by metallographic examination of each specimen after test, to determine from the amount of transformed 4 where the specimen had been heated in relation to the critical temperatures. Results were in reasonable agreement with information from the supplier. Strip tensile specimens were of full sheet thickness and taken along the rolling direction, except for those

Jan 1, 1968

By Secretary of the Interior

"INTRODUCTION The Bureau of Mines Synthetic Liquid Fuels Program again forged ahead during 1952, and important technical advances led the way to improved methods of converting coal and oil shale into liquid fuels. Marking the eighth year of activities under this program, the pact 32 months brought a new domestic industry nearer realization.The increasing demand for gasoline and oil and the rising cost of finding new petroleum, coupled with America's growing dependence on imports and the unsettled international situation, have continued to emphasize the importance of the Bureau's Synthetic Liquid Fuels Program. Oil, the indispensable material of wartime, likewise has critical importance in peacetime, touching as it does the life of every individual. Supplementing petroleum with synthetic liquid fuels will not only conserve this Nation's petroleum reserves but also will bring into greater use its tremendous reserves of coal, as well as the vast deposits of oil shale for which no other practical use has yet been found.The Bureau of Mines Synthetic Liquid Fuels Program is one of the most important and far-reaching of the Government's research projects. Through development of commercial synthetic liquid fuels, the United States can obtain oil products from its great inland reserves of coal and oil shale to supplement petroleum in any quantity that may be necessary, consistent with economic and other requirements, such as national defense. The use of raw materials from such deposits would be of highest importance in wartime, when shipping lanes are menaced by the enemy. The Synthetic Liquid Fuels Program of the Bureau of Mines and research efforts of industry have advanced. American technology to the point where it is now possible to begin the design and construction of prototype plants. Certainly, significant improvements will be made as the program continues, but this prospect in no way alters the fact that the start of prototype plants should be encouraged. These plants, as the first step in the development of a synthetic fuels industry, would serve a threefold purpose:"

Jan 1, 1953

By R. E. Boni, G. Derge

Application of surface tension measurements has been made to molten silicates in order to determine the effect of sulphur upon the surface tensions of synthetic blast furnace slags. In melts with the same molar ratios of AI2O3 + SiO2 to the basic oxides BaO, CaO, and MgO, the surface tensions increase in the order of oxides listed. Sulphur lowers the surface tensions of the basic BaO, basic CaO, acid BaO, acid CaO, and acid MgO slags in that order; and the concentration of excess sulphur at the slag surface increases in this same order of slags. The rate and amount of desulphurization of iron by these slags is favored by a low excess surface sulphur in the slag. IN a previous paper,1 the authors discussed the applications of surface tension measurements of molten silicates to problems of metallurgical interest. Of major importance is the aid that such studies lend to forming a working concept of slag structure. Since the ability of a slag to desulphurize metal depends strongly upon its composition,2"4 fundamental information about the structural differences between various slags which contain sulphur should aid the development of better desulphurizing media. For that reason, the present investigation concerns the effect of sulphur upon the surface tensions of synthetic blast furnace slags. Experimental Procedure , The maximum bubble-pressure method was used to measure the surface tensions of synthetic blast furnace slags in the temperature range 1300° to 1600°C. The method is based upon the equation which was developed by Schrödinger5 from a consideration of the forces of hydrostatic pressure and surface tension of a liquid which oppose bubble formation when a gas is forced through a tube immersed in the liquid. where y is the surface tension between argon and slag in dynes per centimeter; g is the gravitational constant, centimeters per second2; H is the manometer reading in centimeters; s2 is the density of manometer fluid in grams per cubic centimeter; S1 is the density of the medium in grams per cubic

Jan 1, 1957

By R. England

"This paper describes the objectives and design parameters for the operation of a computerized In-The-Hole (I. T.H.) Drill. The principal objective is to add computer control to an Inco 00-60 I. T.H. (CMS-CD-90) drill in order to drill holes with greater accuracy. The computer provides control of the angle of the hole by maintaining the orientation of the drill head, and optimizes the straightness of the hole by maintaining a constant force on the drill bit.The second objective is to provide the greatest degree of operational automation, so the objective outlined above can be accomplished with a minimum of operator intervention.In order to provide full operational automation it was necessary to also provide the capability for the computer to add and remove drill rods. To accomplish this, a rod-handling mechanism consisting of a rod storage rack and rod manipulator arms was used.IntroductionMining machinery that lacks automatic control has been found to show a high degree of variation in work output and performance quality when operated by different personnel. Differences in operator attitude, judgment, and skill are reflected directly by production statistics. The addition of automated control has the potential for considerable improvement in machine life and performance. Even with a more acceptable mine environment and much safer conditions than ever before, situations still exist where it is preferable to remove personnel for reasons of safety as well as productivity. Typical advantages of such situations are automated skip loading and hoisting, and the use of remote control load-haul-dump units exposed to open stopes.Other cases arise where heavy work is required under conditions where lighting is poor, floors are slippery, noise levels are high and dust and oil mist exist in the atmosphere. I.T.H. drilling is carried out under such conditions and is one operation where automation can easily be justified."

Jan 1, 1987

By Allen G. Gray

It&apos;s not news to you that the United States is highly vulnerable to potential problems in supply of critical and strategic metals, and that these metals - chromium, for example - are employed in important bearing alloys. It&apos;s also not news to you that there is a significant challenge to improve durability and life of bearing systems which contribute to conservation as well as productivity. The objectives of this workshop are to identify available technologies and opportunities for new technologies in conservation, substitution, and displacement of critical and strategic metals in bearing systems. These considerations are among the most viable options for reducing vulnerability to a cutoff of chromium and other critical metals and action should be taken to identify and develop those technologies now rather than after a crisis is upon us.

Jan 1, 1984

By John F. Gamble

Amphiboles are hydrated mineral silicates five of which occur in asbestiform habits as asbestos grunerite (amosite) asbestos, riebeckite (crocidolite) asbestos, anthophyllite asbestos, tremolite asbestos and actinolite asbestos] and non-asbestiform habits (grunerite, riebeckite, anthophyllite, tremolite and actinolite). The asbestiform varieties are characterized by long, thin fibers while non-asbestiform varieties such as cleavage fragments form short fibers with larger widths. The U.S. regulatory method for counting asbestos fibers (aspect ratio [>]3:1, length [>]5 µm) does not distinguish between asbestos and cleavage fragments. The method biases toward increased counts of non-asbestiform cleavage fragments compared to long, thin asbestos fibers. One consequence of this regulatory approach is that workers can be erroneously classified as exposed to concentrations of asbestos (asbestiform amphiboles) above the U.S. 0.1 f/mL exposure standard when in fact they are not exposed to asbestos at all but non-asbestiform amphibole cleavage fragments. Another consequence is that the known carcinogenic effects of asbestos may be falsely attributed to non-asbestiform amphibole cleavage fragments of the same mineral. The purpose of this review is to assess whether amphibole cleavage fragments pose the same risk of lung cancer and mesothelioma characteristic of amphibole asbestos fibers. We identified three groups of workers exposed to non-asbestiform amphiboles: two groups exposed to grunerite (Homestake gold miners and taconite miners) and one group exposed to industrial talc containing non-asbestiform tremolite and anthophyllite in St. Lawrence County, NY. In addition to assessing strength of association and exposure?response trends in the non-asbestiform amphibole cohorts, comparisons were also made with cohorts exposed to the asbestiform counterpart (positive control) and cohorts exposed to the mineral (e.g. talc) that does not contain amphiboles (negative controls). The cohorts exposed to non-asbestiform amphiboles had no excesses of lung cancer or mesothelioma. Similar results were observed in the negative control groups, in stark contrast to the excess risks of asbestos-related disease found in the asbestos cohorts. The only possible exception is the twofold increased risk of lung cancer where exposure was to industrial talc containing cleavage fragments of tremolite and anthophyllite. However, this risk is not considered attributable to the talc or amphibole cleavage fragments for several reasons. A similar increased risk of lung cancer was found in Vermont talc workers, studied in the same time period. Their exposure was to relatively pure talc. There was no relationship between lung cancer mortality and exposure measured as mg/m3 years and years worked. A case?control study reported that all the lung cancer cases were smokers (or former smokers) and attributed the excess to smoking. There were two mesothelioma cases among the NY State talc workers exposed to cleavage fragments of tremolite and anthophyllite, but talc is not a plausible cause because of too short latency and potential for previous asbestos exposure. The positive controls of tremolite asbestos and anthophyllite asbestos exposed workers showed excess risks of both lung cancer and mesothelioma and positive exposure? response trends. St. Lawrence, NY talc does not produce mesotheliomas in animals while amphibole asbestos does. In sum, the weight of evidence fully supports a conclusion that non-asbestiform amphiboles do not increase the risk of lung cancer or mesothelioma. ©2008 Published by Elsevier Inc. Keywords: Amphiboles; Cleavage fragments; Lung cancer; Mesothelioma; Asbestos; Non-asbestiform amphiboles; Grunerite; Talc

Jan 1, 2007

By V. N. Bryant

"1.0 SYNOPSISThe Colomac property, located 137 miles by air northwest of Yellowknife in Canada's NWT. will recover gold from 10,000 tons per day of open pit ore.The decision to proceed with the project was based on a mineable ore reserve of 16 million tons (including dilution) averaging 0.064 oz/ton. After an in-fill drilling program in the latter half of 1988, Colomac's mineable, proven and probable ore reserves were increased to 28 million tons averaging 0.056 oz/ton of gold.A feasibility study completed by Wright Engineers for Neptune Resources in December 1987 examined the possibility of vat leaching followed by C.l.P. and electrowinning. A second feasibility study completed by Wright in February 1988 demonstrated that a conventional agitated leach circuit using a finer grind justified the higher capital cost of this process. This study was accepted and formed the basis of the project authorization.Preliminary engineering commenced in April 1988 and detailed engineering was started in September of that year with the objective of a mine/mill start-up by early 1990.The short time period available to meet the project deadline was additionally challenging, as site access is either by plane year round, and winter road from early February to late March. Normal lead times for equipment design, specifications, quotations and bid analyses were not possible, if the winter road time-slot was to be met."

Jan 1, 1990

The following list contains the names of members of whose deaths notices have been printed in MINING AND METALLURGY during the year ending April 1, 1937. Biographical sketches published in MINING AND METALLURGY are indicated in the last two columns. YEAR OF ELECTION - NAME - DATE OF DEATH - ISSUE CONTAINING BIOGRAPHY - PAGE I892 ALLDERDICE, TAYLOR May 20, I934 1919 ALTMEYER, MAURICE E June 9, I936 1917 ANDERSON, JAMES P Jan. I4, I937 I936 ANDERSON, O RAN M Jan. 12,1937 I908 AUSTIN, E. A I935 1914 BACON, MAURICE W Jan. 4, I936 Apr. I936 22I 1914 BARTHOLOMEW, WILLIAM F Oct. 7, I936 Dec. I936 602 I930 BERRY, HAROLD R July 1, I936 1915 Betts, Robert M Jan. 9, I937 HON

Jan 1, 1937

By H. Powell

"This paper discusses how elemental analysis of conveyed bulk flows in real time using PGNAA (Prompt Gamma Neutron Activation Analysis) technology has resulted in significant improvements in advancing plant control in mineral processing operations. PGNAA through belt, full stream, continuous, multi-elemental, real time analysis technology is explained. Capabilities and limitations in plant operating environments are discussed including comparison with other real time, on-line technologies through review of published information available for on-conveyor minerals applications. Case studies include an iron ore and copper-gold company, both of which consider the technology an essential component in advanced plant control necessary in new process flow sheet designs, rather than an optimisation tool.INTRODUCTION Process operators rely on supply of a reasonable ore quality and consistency from the mine. Unfortunately neither the mining nor process operators have much control over the ore quality once it has been put into the crusher. Grade control typically stops once the material is designated as ore and the process plant operator needs to process it irrespective of quality. Plant control is most effective when technologies measure process streams directly and preferably in real time. Measuring sampling streams that are not representative of the primary flow will result in incorrect plant control decisions. Sampling coarse conveyed flows is expensive and impractical at many operations, however, this does not mean those flows cannot be measured. Investigations to find techniques suitable for real time elemental analysis have focussed on the application of known laboratory techniques to process streams. For conveyed applications, development of neutron irradiation techniques were most promising and early studies indicated potential success for bauxite measurement (Beurton et al, 1995). Tran & Evans (2001) concluded there was no equivalent technology to PGNAA in terms of material penetration power and that the technology was eminently suitable for basic industries such as cement. Nelson and Riddle (2003) evaluated PGNAA for possible use in the phosphate industry by using a unit installed in a cement plant to test performance on phosphate samples and ultimately recommended its use for further characterisation of the mine’s various ore types to improve stockpile allocation and grade control"

Jan 1, 2014

Flue dust from the sintering of base metal sulphides was leached to remove cadmium and arsenic. Leach liquor contained cadmium, zinc and small amounts of other base metals as chlorides. Results are reported of the use of a cation exchange resin Zeocarb 225 to separate the base metals from the arsenic. The resin was eluted with sodium chloride or sulphate to give a solution of relatively concentrated cadmium suitable for recovery by zinc cementation. The limited solubility of sodium sulphate presented some practical problems which were investigated. Another problem was the precipitation of lead sulphate in the resin during elution.INTRODUCTIONWhen lead-zinc sulphides are sintered prior to smelting, the gases passing to the flue are mainly uncondensable but contain a certain proportion of sublimates and dust particles which deposit in the flue or are carried, after condensation in the gas stream, to some form of dust extraction equipment.The recovered dust is a complex mixture of base metal sulphates, sulphites, sulphides, chlorides and oxides, the composition depending on the original concentrates. A large proportion of the cadmium and some of the arsenic originally in the concentrates finds its way to this flue dust, the treatment of which can be a convenient means of removing these elements and controlling their concentrations in the main lead-zinc smelter circuit. However, disposing of this material represents an appreciable waste of base metals as well as a serious toxicity hazard.Sulphide Corporation Pty. Ltd. was faced with this problem in planning the flow sheet of the new lead-zinc smelter at Cockle Creek, N.S.W. From a test run carried out on a pilot plant at Avonmouth, U.K., using a mixture of lead and zinc concentrates, a sample of dust was obtained for...

Jan 1, 1960

By Gerald H. Luttrell, Seyed Hassan Amini, Aaron Noble

One of the most important processing engineering tools for designing mineral processing facilities is linear circuit analysis. This technique, originally conceived and developed by Meloy, Williams, and Fuerstenau nearly four decades ago, provides fundamental insights regarding how unit operations interact and respond when arranged in multi-stage processing circuits. Researchers have successfully utilized this tool to improve the operating performance of industrial processing circuits incorporating coal spirals, magnetic separators, mineral spirals, and eddy current separators. More recently, advanced versions of this tool have also been developed to provide a standardized framework for circuit mass balance calculations, to output exact analytical solutions to mass yield and value-based efficiency expressions, and to estimate uncertainty propagation in separation circuits. This article reviews the historical development of linear circuit analysis, describes how the technique has evolved to address more complex circuit design problems, and presents industrial case studies that highlight the importance of this process engineering tool.

Nautilus Minerals and Neptune Minerals are betting that the next great metals rush will take place more than 1,500 m (5,000 ft) below the sea. Nautilus is the first company to commercially explore the ocean floor for gold and copper seafloor massive sulfide (SMS) deposits. Its main focus is the Solwara 1 Project, a polymetallic copper, gold, zinc, silver deposit that is under 1,600 m (5,200 ft) of water off the coast of Papua New Guinea in the western Pacific Oceans? Rim of Fire. Nautilus Minerals, in a joint venture with Placer Dome (now Barrick Gold), began its exploration of what would become the Solwara 1 area in 2005 with side scan sonar and dredge sampling. The dredge and grab sampling confirmed the grade tenor of earlier sampling by scientific research programs. The 45 dredge samples aver-aged 10.8 percent copper, 3.7 percent zinc, 224 g/t (6.5 oz/st) silver and 13.7 g/t (0.4 oz/st) gold. Nautilus has since staked out more than 300,000 km2 (115,800 sq miles) of tenement licenses and exploration applications in the waters off Papua New Guinea, Fiji, New Zealand, Tonga and the Solomon Islands. That is an area about the same size of the United Kingdom. Interest in Nautilus and its projects has grown tremendously since its inception. The company is now listed on the Toronto Stock Exchange. It has raised more than $300 million and spent more than $23 million on exploration. The company has gained the backing of mining majors such as Teck Cominco, Epion, Anglo American and Barrick Gold. It is positioned to become an emerging producer in 2010. Teck Cominco recently agreed to exercise share purchase warrants to acquire three million additional common shares of Nautilus at a price of US$15 million. This will take Teck Cominco?s shareholding to approximately 7.2 percent of the issued shares. Teck Cominco will conduct and manage a ship-based exploration program that will run in addition to the exploration that was already planned for 2008.

Jan 1, 2008