Search Documents

By T. Holmes, J. Middlemiss

"Agnico-Eagle (AE) has been operating their Kittila Mine in Northern Finland since 2008. The mine has experienced considerable ore flow problems with ratholing, bridging and freezing in their mill feed bin since start up. In the first winter of operation, the entire central portion of the contents of the cylindrical flat-bottomed 2000 tonne mill feed bin froze. Flow was erratic and could only be achieved through small diameter ratholes. To maintain a reasonable, albeit limited, feed to the mill, the bin had to be kept less than ½ full and a portable steam generator was brought in to melt the frozen agglomerates that frequently blocked the outlets. The combination of limited surge capacity and frequent outages required the crushing plant to operate 24/7 and resulted in inconsistent production levels and high operating costs.AE had planned to expand the processing plant to increase throughput by about 30% when they transitioned from open pit to underground ore. These plans presented an opportunity to improve the material handling.To avoid the problems experienced with the original mill feed bin, AE enlisted Jenike & Johanson Ltd. (J&J) to test samples of the ore, and based on the measured flow properties to provide design recommendations to ensure that the new mill feed bin would operate reliably. The new 2000 tonne expanded flow mill feed bin and apron feeder were installed in 2014 and are now supplying almost 93% of the total mill feed with the remaining coming from the original bin.IntroductionIn early 2009, AE engaged J&J to visit their then recently opened Kittila mine and mill in Northern Finland (Figure 1). Over the first half-year of operation, production had been restricted in the ore handling and storage system by flow problems such as ratholing, bridging and freezing including blockages of chutes and hoppers as a result of frozen fines buildup and large frozen agglomerates. AE wanted to increase production in the existing open pit mine and mill feed operation and also wanted to avoid similar ore handling problems when they commissioned the new underground mining system under development at that time."

Jan 1, 2017

By Barry Voight

The law [ ] where [ ] is a measurable quantity such as strain and A and cu are empirical constants, describes the behavior of materials in terminal stages of failure under conditions of approximately constant stress and temperature. Applicable to intact rock and rock masses, the relation may be extended to conditions of variable stress and cyclic stress, and may be used to predict time to failure. Applications in rock mechanics include slope and excavation stability and various topics in ground control.

Jan 1, 1989

By H. O. Hofman

Discussion of the paper of H. O. HOFMAN and JOHN BLATCHFORD, presented at the New York meeting, February, 1916, and printed in Bulletin No. 109, January, 1915, pp. 91 to 97. ROBERT H. RICHARDS, Boston, Mass.-I should like to ask Professor Hofman whether he is able to roast his stibnite without any comparatively large amount of loss of antimony? H. O. HOFMAN, Boston, Mass.-Yes. The last statement I made was that the loss of antimony, during those tests, increased with the temperature, and that up to 372° C. there was no loss whatever in antimony, also that it increased to 4:2I per cent. with 545° C., the highest temperature that we obtained in our small furnace. ROBERT H. RICHARDS.-I should like to ask a second question, and that is, is it not true that stibnite can be roasted more completely than any other sulphide?

Jan 5, 1916

By Jeffrey M. Listak

This report describes a study, conducted jointly by BethEnergy Mines Inc. and the Bureau of Mines, to assess the effects of longwall front abutment loading on various supplemental support materials utilized in a predriven recovery room. The purpose of the predriven recovery room is to reduce longwall equipment transfer time by eliminating the premove preparation associated with conventional recovery methods. In addition, the room provides a large area in which face salvage equipment can maneuver. Results of four recovery-room study areas show the progression and influence of the front abutment on the longwall panel and supports and their subsequent behavior. The best performance (i. e. the support that most facilitated recovery) of support material was achieved through the use of a concrete mixture which had a sand content of 35 percent by volume. The longwall transfer time was reduced by 30 percent which translates to a production advantage of 37,000 raw tons of coal per panel.

Jan 1, 1989

By Morris Cohen

STAFF: Editor, Gerhard Derge Acting Editor, Paul G. Shewmon Carnegie Institute of Technology Schenley Park Pittsburgh 13, Pa. Editorial Assistant, M. A. Redmerski Production Editor, Otto T. Johnson THE METALLURGICAL SOCIETY: Karl L. Fetters, President; J.S. Smart, Jr., Past-President; R. C. Cole, Vice President; R. L. Hennebach, Treasurer; R. W. Shearman, Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: W. O. Phil-brook, Chairman; H. L. Bishop, R. C. Cole, J. N. Hobstetter, W. A. Krivsky, E. R. Morgan, F. C. Langenberg, R. E. Lund, Paul Queneau, L. L. Seigle, R. L. Smith, and T. V. Wainwright. Review and selection of manuscripts is under the supervision of the following Publicotions Committes: Extractive Metallurgy Division: R. E. Lund, Chairman; M. E. Wadsworth, Vice Chairman; D. H. Baker, Jr., G. M. Bell, R. E. Grace, W. A. Krivsky, R. A. Lewis, Charles O'Neill, A. W. Schlechten, R. E. Shinkoskey, and W. W. Stephens. Iran and Steel Division: T. V. Wainright, Choirman; H. L. Bishop, R. E. Boni, T. E. Dancy, D. W. Murphy, Johannes M. Uys, J. B. Wogstoff, and R. G. Ward. Institute of Metals Division: J. N. Hobstetter, Chairman; P. A. Beck, J. J. Becker, G. F. Bolling, J. 0. Brittain, J. B. Clark, R. S. Davis, A. E. Dwight, R. W. Fountain, L. R. Girifolco, J. C. Gurland, H. S. Kalish, E. L. Harmon, J. J. Heger, A. A. Hendrickson, L. Himmel, J. P. Hirth, H. H. Johnson, Jr., R. R. Nosh, T. N. Rhodin, R. H. Richman, H. C. Rogers, W. Rostoker, C. Sherby, C. W. Spencer, L. Slifkin, J. K. Stanley, R. Steinitz, H. C. Stumpf, and R. Swalin. Published bimonthly by the Americon Institute of Mining, Metallurgicol, and Petroleum Engineers, Inc., 345 East 47th Street, New York 17, N. Y. Telephone PLaza 2-6800. Subscription $30 peryear for non-AIME members in United States and North, South, and Centrol America; $32, foreign; $30per$7.50 for AlME members. Single copies, $6.00, single copies foreign, $6.50. The AlME is not responsible for any stotement made or opinion expressed in its publications ... Copyright 1962 by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . . . Registered cable address, AlME New York . . . Indexed in Engineering Index, Industrial Arts Index, and Chemical Abstracts . . . Second class postage paid at New York, N. Y., and Ann Arbor, Mich. Volume 224, Number 4.

Jan 1, 1962

By K. O. Bennington

Enthalpies of formation of three sodium titanates were determined by hydrofluoric acid solution calorimetry, The values obtained for formation from the elements at 298.15° K are -370.9±0.5 kcal/mole for Na2TiO3, -832.1±0.9 kcal/mole for Na2Ti307, and -1,510.9±1.7 kcal/mole for Na2Ti6013. Tables of enthalpies of formation and Gibbs energies of formation are given as a function of temperature both from the elements and from the component oxides for Na2Ti03 and Na2Ti307.

Jan 1, 1973

By Xinlei Jia, Wenming Guo, Yanling Zhang

A large amount of stainless steel dust rich in Fe, Cr, and Ni has been being generated in China. Smelting treatment is accepted as a practical method for the recovery/reutilization of these second resources, during which Fe, Cr, and Ni is reduced into one metal phase and then separated from the residue slag. Based on the typical compositions of stainless steel dust, the residual slag can be termed as CaO-SiO2-MgO-Al2O3 system. In this paper, the activity coefficients of Cr in Fe-Cr-Ni-C (-Si/Al) melt and the properties of CaO-SiO2-MgO-Al2O3- 1%CrO system thermodynamically approached. Then, in laboratory experiments, the recovery ratios of Cr and its distribution behaviors between Fe-Cr-Ni-C melt and CaO-SiO2-MgO-Al2O3 slag system were examined.

Jan 1, 2015

By S. J. Stokowski

An extensive drilling and laboratory testing program indicates that diagenetic dolomitization of the Oligocene Sombrerito Fm. limestone, southwestern Dominican Republic, is detrimental to the usefulness and quality of the potential construction aggregate resource. The first part of this program was the collection, photographing, and geologic logging of diamond drill cores to allow lithologic subdivision of the strata into potential quarry layers. The primary lithostratigraphic units are: I (youngest) approximately 10 m of white, dense marine limestone; II, approximately 5 m of white, interbedded dense and chalky marine limestone; III, 2+ m of tan, chalky calcitic dolomite. Unit I has been often altered by lateritic weathering and/or dolomitization; Unit II is often altered by dolomitization. The quarry layers were individually crushed, by core, into coarse aggregate sizes for chemical and physical (specific gravity absorption, MgSO4 soundness, sand equivalent, and LA degradation) analyses. The non-weathered units decrease in coarse-aggregate yield and quality with depth and dolomitization. Dolomitization typically causes about 5% lower yield of coarse aggregate, a sand equivalent of about 20 units below the original value, an increase in absorption of about 3%, an increase in the LA of up to 13%, and a decrease in the average 5-cycle MgSO4 soundness by about 17%.

Jan 1, 1987

By M. Machikicho, N. R. Shoko, J. Chirasha

Keywords: Pyrometallurgy, furnace, ferrochromium, alloys, Zimbabwe Zimbabwe Alloys was founded in 1949 by a consortium led by the John Brown Group. It was the first ferrochrome plant in Africa. The establishment of the refinery was necessitated by an increase in world stainless steel demand and the need to reduce cost by shipping alloy rather than chrome ore. The location of the refinery in Gweru was influenced by a number of factors, not least of which were the abundance of chrome ore deposits, access to inexpensive power from Kariba, the availability of reductant coke from Hwange, accessibility to ports (as the town was well served with rail and road networks second to none in the country), and of course cheaper labour costs. The production of Low Carbon Ferrochrome (LCFeCr) was commissioned in 1953 and produced from an Open Arc Furnace with a Submerged Arc Furnace producing Ferrosilicon Chrome (FeSiCr) that is used as a reductant in the production of LCFeCr. An experimental furnace was commissioned in 1958 to help with efficiency and control on larger furnaces. A second Submerged Furnace was commissioned in 1963. Three other Submerged Arc Furnaces were built between 1967 and 1974. Several mines were acquired between 1974 and 1984, as a strategic move to ensure the growth of the refinery. A briquetting plant was commissioned in 1977, enabling the use of friable ores to enhance the capacity of ore supplies and ore cost management. A plant to recover alloy from slag was established in 1994 to capitalize on market demand without large capital outlay that would be required to build other furnaces to increase capacity. Zimbabwe Alloys has created employment opportunities throughout the years. There have been direct employment opportunities at both the refinery and the mining divisions. With time, indirect employment was realised both upstream and downstream of the refining process, enhancing the livelihood of numerous people. Zimbabwe Alloys' involvement with various labour skills has, of necessity, enabled it to develop a culture of safety at work, home, and play. Zimbabwe Alloys has contributed to society by participating and funding various local initiatives primarily to impact positively on societal needs. The latest development was in 1996, when Zimbabwe Alloys entered into a Technical Transfer Agreement with Japan Metals and Chemicals to improve the efficiencies and hence the profitability of the LCFeCr production process. A significant quantity of various alloys has been produced since inception, and significant foreign currency has been earned for the country. This was in spite of challenges that included the cyclic nature of market prices, the upheavals of sanctions affecting the macro-economic environment, and the challenges related to the deteriorating grade of chrome ore and reductant coke.

Jan 1, 2006

By Arnlf Muan, Bert Phillips

The quenching technique has been used for- a study of phase velntiorzs within the composition triangle 2CaO.Fe2O3-FeO.Fe2O3 Fe2O3 of the system Ca-Fe-O. Desired total compositions of sanzples were attained by weighing of starting materials in required proportions and keeping them in sealed 80 pct Pt 20 pct Rh tubes during equilibration .runs. The liquidus surface has been delineated. the existence of two ternary compounds has been established, and seven ternary inwariant situations have been determined. ONE unit within the research program on refractory oxides in progress in our laboratories is the study of phase relations in the system Ca-Fe-Si-O. The present paper deals with the ternary system 2CaOFe2O3-FeO.Fe2O3-Fe2O3, which is only a small part of the enormously complex quaternary system. Many of the phases occurring in iron ore sinter products have compositions which can be closely approximated within this ternary system, and a knowledge of stability relations existing among these phases may be expected to be a useful guide for improving sintering operations. Two fundamentally different experimental approach es are commonly used in studies of systems containing iron oxides, both permitting control of the oxidation state of Fe. One method consists in keeping constant the oxygen partial pressure of the gas phase in equilibrium with condensed phases (liquid and crystalline). In the other method, which is the one used in the present investigation, the total composition of condensed phases is kept essentially constant by keeping the samples in a gas-tight container. The details of this experimental procedure will be described in a later section. PREVIOUS WORK Extensive studies of phase relations in the bounding binary system FeOFe2O3-Fe2O3 have been reported by Greig, Posnjak, Merwin, and Sosman,' by Darken and Gurry,2, 3 and recently by Phillips and Muan.4 A diagram summarizing the results of these studies is shown in Fig. 1. Particular attention is

Jan 1, 1961

By E. T. Turkdogan, P. Grieveson

STAFF: Editor, Gerhard Derge Acting Editor, Paul G. Shewmon Carnegie lnstitute of Technology Sc hen ley Park Pittsburgh 13, Pa. Editorial Assistant, M. A. Redmerski Production Editor, Otto T. Johnson THE METALLURGICAL SOCIETY: Karl L. Fetters, President; J.S. Smart, Jr., Past-President; R. C. Cole, Vice President; R. L. Hennebach, Treasurer; R. W. Shearman, Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: W. 0. Phil-brook, Chairman; H. L. Bishop, R. C. Cole, J. N. Hobstetter, W. A. Krivsky, E. R. Morgan, F. C. Langenberg, R. E. Lund, Paul Queneau, L. L. Seigle, R. L. Smith, and T. '4. Wainwright. Review and selection of manuscripts is under the supervision of the following Publications Committes: Extractive Metallurgy Division: R. E. Lund, Chatrmon; M. E. Wodsworth, Vice Chairman; D. H. Baker, Jr., G. M. Bell, R. E. Groce, W. A. Krivsky, R. A. Lewls, Charles O'Neill, A. W. Schlechten, R. E. Shinkoskey, and W. W. Stephens. Iron and Steel Division: T. V. Wainright, Choirman; H. L. Bishop, R. E. Boni, T. E. Dancy, C. W. Murphy, Johonnes M. Uys, J. B. Wagstaff, and R. G. Ward. lnstitute of Metols Division: J. N. Hobstetter, Chairman; P. A. Beck, J. J. Becker, G. F. Bolling, J. O. Brittain, J. 8. Clark, R. S. Davis, A. E. Dwight, R. W. Fountain, L. R. Girifalco, J. C. Gurland, H. S. Kclish, E. L. Harmon, J. J. Heger, A. A. Hendrickson, L. Himmel, J. P. Hirth, H. H. Johnson, Jr., R. R. Nosh, T. N. Rhodin, R. H. Richman, H. C. Rogers, W. Rostoker, C. Sherby, C. W. Spencer, L. Slifkin, J. K. Stanley, R. Steinitz, H. C. Stumpf, and R. Swolin. Published bimonthly by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc., 345 East 47th Street, New York 17. N. Y. Telephone PLaza 2-6800. Subscription $30 per year for non-AIME members in United States and North, South, and Central America; $32, foreign; $7.50 for AlME members. Single copies, $6.00, single copies foreign, $6.50. The AlME is not responsible for any statement made or opinion expressed in its publications ... Copyright 1962 by the American lnstitute of Mining, Metollurgical. and Petroleum Engineers. Inc. . . . Registered cable address, AlME New York . . . Indexed in Engineering Index, lndustriol Arts Index, and Chemical Abstracts . . . Second class postage paid at New York, N. Y., and Ann Arbor, Mich. Volume 224, Number 6.

Jan 1, 1962

By Waldemar W. Koczkodaj, William O. MacKasey

A consistency-driven pairwise comparisons method for mineral potential assessment is presented, using a simpli?ed case of volcanic-associated massive sul?de type deposits as an example. Geological, geochemical, and geophysical criteria are considered on two levels: local and regional. The local geological criteria are subdivided into stratigraphy, lithology, alteration and/or mineralization, and structure. The concept of geomerit index and a procedure for computing this index are introduced. The method of consistency-driven pairwise comparisons can be combined with other quantitative and qualitative assessment methods, enhancing them by incorporation of non-measurable geological criteria (e.g., stratigraphy or lithology) and by computation of weights. The consistency-driven approach allows experts to re?ne at-times subjective judgments concerning exploration and land-use planning, and contributes to the improvement of mineral-potential assessments.

Jan 1, 1997

By Waldemar W. Koczkodaj, William O. MacKasey

Abstract - A consistency-driven pairwise comparisons method for mineral potential assessment is presented, using a simplified case of volcanic-associated massive sulfide type deposits as an example. Geological, geochemical, and geophysical criteria are considered on two levels: local and regional. The local geological criteria are subdivided into stratigraphy, lithology, alteration and/or mineralization, and structure. The concept of geomerit index and a procedure for computing this index are introduced. The method of consistency-driven pairwise comparisons can be combined with other quantitative and qualitative assessment methods, enhancing them by incorporation of nonmeasurable geological criteria (e.g., stratigraphy or lithology) and by computation of weights. The consistency-driven approach allows experts to refine at-times subjective judgments concerning exploration and land-use planning, and contributes to the improvement of mineral-potential assessments.

Jan 1, 1997

The addition of a thallous salt to the cyanide leach of a calcined pyritic concentrate causes a marked increase in the rate of extraction of gold. This is due probably to the activation of passive gold by the thallous ions. Lead, bismuth, and mercury salts, which should produce a similar effect, fail to do so. It is postulated that this latter result, together with the reprecipitation of silver at low cyanide levels, is due to the presence of soluble sulphide.INTRODUCTIONThe work of Fink and Putnam (1950) showed that the rate of solution of gold in cyanide can be increased by the addition of small amounts of lead, bismuth, mercury, and thallium salts. Mills (1951), during a study of the electrochemistry of gold, with particular reference to cyanidation, was able to show that gold may become passive towards cyanide solution. The addition of lead or thallium salts prevented this passivity, although the action of lead was limited to the pH range 10 to 12. In a recent paper Cathro (1963) confirmed the findings of Mills, and presented results which showed that the addition of thallium to a cyanide leach of a calcine from Lake View and Star mine, Kalgoorlie, increased the rate of extraction of gold appreciably. In, this paper the use of thallium to prevent the gold becoming passive, and hence to decrease leaching time and cyanide consumption, is examined.EXPERIMENTALA series of leaching tests was carried out on a sample of Lake View and Star calcine, comprising calcined pyrite (about 70 per cent.) and siliceous gangue (about 30 per cent.) and containing 165 p.p.m. gold, 45 p.p.m. silver, 0·1...

Jan 1, 1964

By E. Czech

Hydrogen generated through aluminum-assisted water split reaction is a novel, efficient and environmentally friendly method. It has been found previously that the passivation of aluminum can be prevented in neutral (pH=7) or near neutral pH conditions in water by grinding aluminum with a catalyst, such as A12O3, SiO2 or SiC. Recently, the best results have been obtained by using water-soluble inorganic salts (WIS), ground with aluminum. The massive, rapid corrosion reaction of the Al-WIS system which takes place in regular tap (or marine, or ground) water can be utilized to produce hydrogen by aluminum-assisted water split reaction, in-situ, on-demand. The reaction offers clean, low-cost, environmentally benign and entirely recyclable technology for on-board on-demand hydrogen generation. Besides pure gaseous hydrogen, only pure solid aluminum hydroxides AlOOH or Al(OH)3 are formed as the reaction products. The hydrogen yield and Al-WIS reaction efficiency are high. From 1 g of mechanically alloyed aluminum powder, up to 1.25 liters of hydrogen were generated, i.e. efficiency up to 92% was achieved. The amount of hydrogen and hydrogen generation rate depend on various reaction parameters. The effect of chemistry and concentration of additives, water temperature, powder particle size and milling conditions on the reaction kinetics will be presented and the possible process mechanism will be discussed.

Jan 1, 2005

By Hans Hamrin

Three drill-blast cycles of 3.1 m advance achieved in one working shift of 7.5 hours at the Holsfjorden Tunnel project in Norway. The tunnel, 5235 m long, with a cross section of 8.6 m2, was completed several months ahead of schedule. This remarkable performance was achieved by a crew of 16 men, using machines specially designed for small tunnel excavation. The integration of drilling and charging into one unit, mucking and transport in another, reduced non-productive time considerably. The average cycle time of 140 min made it possible to complete three rounds in one 7.5 hours shift.

Jan 1, 1987

By C. E. Reistle

The tests reported in this paper were made in the East Texas field in the summer and fall of 1932 as a part of the Bureau of Mines study of the operation of flowing wells and reservoir performance; and to determine, if possible, the minimum reservoir pressure necessary to produce the wells in this field by natural flow through different sizes of flow strings. The minimum reservoir pressure that would be required to maintain natural flow through 2 1/2-inch tubing was determined experimentally for the existing energy conditions in the East Texas field. With the present available data, however, it 'is impossible to predict accurately or to determine by calculation the necessary energy requirements for maintaining the vertical flow of oil and gas mixtures under all conditions. Although some valuable data were obtained which seem to have application to the solution of problems involving vertical flow, this important research of the petroleum industry is so involved that more study of the complicating factors influencing the flow of oil-gas mixtures through vertical pipes is required. Versluys4 has presented a mathematical analysis of the vertical flow of oil and gas mixtures which covers the fundamental theories of the problem-although, as he points cut, there are factors, particularly friction, slippage, and solubility of the gas in the oil that must be mown or determined experimentally before the equations he has developed can be applied to actual

Jan 1, 1933

By Klaus Detert, Joseph Ziebs

The progress of primary recrystallization has been studied in alloys of nickel with 0.01, 0.1, and 1.0 at. pct Ta. It can be shown that in one particular alloy containing 0.1 Ta and 0.02 02 a large grain structure (0.5 mm diameter) could he developed by primary recrystallization in thin sheetswhich were cold-worked to 97.5 pct reduction in thickness. Electron transmission microscopy demmstrates that this phenonmena was linked to the occurrence of fine precipitates at subboundaries. A discussion of how fine precipitates can exert under certain circumstances a rather distinct retarding effect on nucleation rate is included. IN a former investigation, the recrystallization and texture formation in a series of binary nickel alloys including pure nickel were studied.' Nickel alloys with some tantalum added displayed peculiarities during primary recrystallization which have been studied in more detail by the present investigation. The alloys were prepared by powder-metallurgy techniques similar to the previous investigations.' Pure metal powders were thoroughly mixed to obtain alloys with 0.01, 0.1, and 1.0 at. pct Ta, referred to as alloy A, B, or C, respectively. The metallic impurities were kept below 0.005 at. pct except iron and cobalt with slightly higher values, by using highly purified nickel and tantalum powders.' The mixtures were pressed into bars and sintered at a temperature of 1300°C. The sintering atmosphere was either high vacuum, dry hydrogen, or wet hydrogen. The sintered rectangular bars were rolled 60 pct to a thickness of 3 mm, then annealed under dry hydrogen at 1000°C and again cold-rolled to about 97.5 pct reduction of thickness. After this heavy deformation, the sheet thickness was 0.07 5 mm. In order to study primary recrystallization which occurred in measurable times between 400" and 600°C, samples of the rolled sheets were annealed in a salt bath at various temperatures for various times in order to study the progress of recrystallization by hardness measurements and microscopic examination. For optical observation, the samples were polished and etched in a solution of 65 cu cm HNO3, and 18 cu cm acetic acid in 20 to 100 cu cm H2O, depending of the particular sample and annealing treatment. For transmission electron microscopic observations, thin foils were prepared by the combined window and Bollmann techniques.273 The electrolyte consisted of 23 pct perchloric acid and 77 pct acetic acid held at 15°C. Polishing was performed at a current density of 0.4 amp per sq cm. The examination of the thin films was accomplished by a Siemens Elmiscope-type electron microscope operating with an accelerating voltage of 100 kv. RESULTS The progress of primary recrystallization was very accurately followed in these alloys in order to establish the time when recrystallization started and ended during an isothermal anneal. Table I gives some of the data obtained by these studies. The time for beginning is a mean value, where somewhat less than 5 pct of the matrix has recrys-tallized. The end of recrystallization is the time when at least 95 pct of the matrix has recrystal-lized. Listed are three different B alloys, with 0.1 Ta distinguished by different sintering atmospheres which influence the rate of primary recrystallization. By the above method, the state of the grain structure when primary recrystallization was completed, but grain coarsening had not started, could be clearly defined. The average grain diameter of the recrystallized matrix is also given in Table I. The grain size did not depend on the temperature of the isothermal anneal. With one exception the grain size of the primary recrystallized matrix was found to be rather fine

Jan 1, 1965

By O. Skiredj, J. F. Elliott

It has been necessary to collate the available data on the solubility of graphite in Fe-Si-Mn alloys for a study of slag-metal equilibria in ferromanganese production. That study will be reported later; the collation is reported here. The carbon content of graphite-saturated liquid iron above 1153ºC by Chipman and co-workers1 is: %C= 1.34 + 2.54 x 10~3t(°C) [l] For graphite-saturated manganese above 1322ºC it is: %C = 2.68 + 3.52 x 1CT3 t(°C) [2]

Jan 1, 1963

By L. J. Lorig

Much of the present knowledge about caving behavior of rock masses has been obtained from empirical observations. Additional notions about caving have been developed through inferences derived from two-dimensional finite element analyses. These analyses have indicated that a combination of one low-angle set of fractures and one nearly vertical set of fractures is the optimum fracturing configuration for ease of cavability of an orebody. This paper presents the results of two- and three-dimensional distinct element analyses which draw different conclusions than those reported from finite element studies. The distinct element method is selected far analysis of cavability because this method treats the rock mass as an assemblage of rock blocks which may interact individually, The results of the analyses are compared to a documented case history which involved a groundfall of 80,000 tons of ore in a 160-foot high pillar. The mechanics associated with these results are-explained in terms of simple static stability analysis of wedges. The propensity for orebody caving is primarily a function of the number of joint sets or potential "release" surfaces in the orebody. This mechanism is influenced by the bounding weak discontinuities, and intact strength of rock material.

Jan 1, 1989