Search Documents

By Y. M. Chen, H. L. Zhang, W. U. Bing, C. Q. Zhou

Multiphase flow in the widely used Vanyukov furnace was numerically studied. An unsteady three-dimensional and three-phase flow model was firstly built using the computational fluid dynamics (CFD) software ANSYS FLUENT®, and then solved with the volume of fluid (VOF) and k - ??model. The results showed that the proposed model could be used to predict the multiphase movement, the slag/air fluctuation, the vortex formation, and effects of structural and operational parameters. By fast Fourier transform (FFT), the dominant frequency of density with time signal was calculated as 0.29 Hz. The analysis of different injection flow rates of enriched air indicated that this variable has a major effect on the mean slag velocity. The peak mean velocity increased from 2.17 to 4.99 m/s while the flow rate of enriched air varied from 70 to 160 m/s. The proposed model provides a method to optimize the furnace structure and operating conditions for the best furnace performance and lowest energy consumption.

Jan 1, 2015

By Francisco Macías

Los drenajes ácidos de mina de la Faja Pirítica Ibérica presentan una elevada acidez y altas concentraciones metálicas. En la mina abandonada de Monte Romero se ha testado un sistema de tratamiento pasivo multi-pasos a escala piloto, para tratar una descarga ácida con un pH de 3, 380 mg/L de Zn, 275 mg/L de Fe, 100 mg/L de Al, 15 mg/L de Mn, 5 mg/L de Cu y 0.1-1 mg/L de As, Pb, Cd, Co y Ni. El sistema consta de un primer pretratamiento denominado NFOL, donde se recrean a gran escala los procesos de atenuación natural observados en las terrazas de Fe de estos ambientes. Posteriormente el agua fluye a través del tratamiento Sustrato Alcalino Disperso (DAS), el cual está formado en primer lugar por dos tanques de 3 m3 rellenos con la mezcla reactiva DAS-caliza (80% virutas de madera y 20% de arena caliza), y conectados en serie con 4 piscinas decantadoras de 6 m3. Finalmente el agua fluye a través de un último tanque de 1 m3 de capacidad relleno con la mezcla reactiva DAS-magnésica (80% virutas de madera y 20% de MgO tamaño polvo). En el pretratamiento NFOL se produce la retención de aproximadamente el 35% del Fe, así como un 75% del contenido en As. En la parte basada en la disolución de la caliza queda retenido el resto de Fe y As, y el 100% de Al, Cu y Pb. Finalmente en el DAS-magnésico la totalidad de Zn, Mn, Cd, Co y Ni son retenidos. Basándonos en esta tecnología y mediante financiación de la Unión Europea a través del proyecto LIFE-ETAD (LIFE12 ENV/ES/000250) se está desarrollando un ambicioso proyecto para la implementación a escala real de un tratamiento pasivo para aguas ácidas con altas concentraciones metálicas, en colaboración con la empresa Sacyr Construcción y la Agencia de Medioambiente y Agua de la Junta de Andalucía.

Sep 21, 2015

By J. P. Jarrell

Environmental considerations are of increasing importance in determining the acceptability, schedule and cost of expansion ofCanada's uranium processing industry. Environmental considerations must be addressed in the early stages of facility planning. This results in a dilemma, as the process data needed to predict physical environmental impacts are not yet available from process design activities. Hence, a business risk is incurred if plant design is carried forward to meet these requirements prior to project (or site) approval. On the other hand, project scheduling normally mitigates against leaving process design engineering until such time as project approval is obtained. This paper examines the experience gained in Eldorado Nuclear's proposed expansion of refining capacity as viewed by an environmental engineering consultant. The history of the project and the relationship to process design functions in the two-year period prior to the Port Granby environmental hearings are reviewed. During the Port Granby public hearing, there was a consensus that normal operation of the proposed refinery could be successfully integrated with the site's natural environmental constraints. Moreover, the radiological impact from plant operations was demonstrated to be inconsequential. However, concerns were raised relating to plant upset and accident situations. These concerns are summarized. Process data requirements identified during the environmental hearings are discussed. Finally, the concerns for on-site burial of radioactive waste are reviewed. These concerns focussed on long-term stability of the waste in the presence ofgroundwater transport, erosion and glaciers. The AECB's position on waste management with regard to this project is reviewed in light ofthe implications for design.

Jan 1, 1979

Building the Unified Comminution Model The Unified Comminution Model (UCM) was formulated with the vision of bringing all comminution models onto a common base. The structure of the model relies on knowledge of the mechanical environment in the comminution devices to predict the modes and rates of collision in a device. A detailed understanding of the breakage modes and an ability to correctly test these modes for the ores in question is then required to feed into the UCM. A model structure has been developed that has the capability of dealing with multiple modes of breakage, such as low energy impact surface damage, chipping, sliding abrasion, cumulative impact body breakage and the transition of rock between modes. A critical review is presented on the shortcomings and limitations of utilising the discrete element method (DEM) to provide the mechanical environments. The assumptions and applicability of utilising DEM in milling models are presented and proposed routes to building a realistic mechanistic model are proposed. Based on this more realistic measures of collision energy have been derived from the DEM simulations, which better mimic the real breakage tests. Generic forms of the collision energy distributions have been observed and developed into functional forms for use in the simulation environment. The method of application of this model to a pilot SAG mill is presented.

Sep 13, 2010

By D. C. Panigrahi

Extensive field studies have been carried out to investigate the pillar fire problems in one coal mine in India. A Thermal IR gun and a Thermovision camera have been employed for thermal scanning to assess the state of heating in selected pillars. Special sampling set-ups have been designed to collect gas samples from the holes drilled into the selected pillars and the multigas detector is used to analyse the composition of samples in situ. In order to predict the spontaneous heating in coal pillars, different gas ratios have been calculated and it has been observed that some of the established gas ratios, viz. Graham?s ratio, Young?s ratio etc. have resulted in negative values in samples containing high amounts of methane. The modified gas ratios have been proposed which will be useful for predicting the pillar fires. These ratios may also be used for assessing the condition of fires in sealed-off areas.

Jan 1, 2004

By G. H. Damon

Since 1963, Bureau of Mines Information Circular 8179 has served the mining industry as a fundamental safety guide in the field of blasting agents. In the intervening 14 years, many changes have occurred, and this report presents revised and new recommendations which recognize these changes. For example, AN-FO is now supplied mostly premixed, whereas in 1963 much of it was mixed by the blaster; aluminum metal (A1) and other fuels are now often added to AN-FO to increase strength, and flake aluminum powder is used as a sensitizer in water gels; and water gels or slurries that are now extensively used were just coming into practical use in 1963. To provide the widest possible margin of safety, some of the Bureau's recommendations are more stringent than existing regulations,

Jan 1, 1977

By AIME AIME

BY COMBINING the sessions on reduction and refining of copper, lead and zinc it was possible to devote an entire day to nonferrous metallurgy. Four interesting papers were presented at the morning session and four more in the afternoon. In the discussion of papers on copper, F. R. Pyne acted as chairman, with H. M. Shepard as vice-chairman, whereas for those on lead and zinc, F. F. Colcord acted as chairman, with C. R. Hayward as vice-chairman. The paper by P. D. I. Honeyman on the smelting of raw concentrates in the reverberatory furnace was presented by Mr. Pyne and discussed by Messrs. Mazany and Hayward. The interesting paper by E. S. Bardwell, com- paring the use of various fuels in copper-refining furnaces at Great Fails, Mont., was presented by Mr. Shepard and discussed by Messrs. Boggs, Gronningsater and Hayward. That by R. G. Knickerhocker, describing the stationary basic copper converter at Messina, Transvaal, was presented by Mr. Pyne, together with a written discussion by c. R. Kuzell, of the United Verde Copper co. It was an interesting illustration of how well-known processes may sometimes be modified to fit into unusual conditions.

Jan 1, 1932

By Marc Dondelinger

Interlocking H sections with deep webs and high section modulus are being used for cofferdams and shore enclosures where pressures are excessive. The H sections can be as much as a meter deep; they can be used as continuous interlocked wall. A steel saving alternate is spacing the H and driving deep for stability then filling between with shorter interlocking sheet piles. Templates provide for exact positioning.

Jan 1, 1985

By R. C. Reed, A. Akhtar

Oxidation of the third generation cast single crystal, nickel-base superalloy CMSX-10 is examined using isothermal tests at 900°C and 1000°C for times ranging from 20 hours to 100 hours. X-ray diffraction, scanning electron microscopy and energy dispersive secondary X-ray analysis were used to characterize the microstructure. It was found that the external scale formed at 1000°C is made up of (Ni,Co)O and the spinel NiCo2O4. The (? + ? ') microstructure of the superalloy transforms into the intermetallic (3 phase prior to the onset of internal oxidation. Internal oxidation results in the formation of (Ni,Co)Ta2O6 and (Ni,Co)WO4. No evidence was found for the formation of alumina (Al203), and the spinels NiCr2O4 and NiAl2O4 in this third generation superalloy. Results of the laboratory investigation are compared with those of an aero-engine turbine blade removed from service and examined earlier.

Jan 1, 2004

By Antonio Karzulovic, Sergio Olavarría, Patricio Adriasola

The economical analyses of different Chuquicamata open pit mine planning scenarios, indicate that the pit closure should occur at latest in the year of 2017. However, about 60,000 m of drill holes have demonstrated that below the pit bottom there is a potential of 2.3 billion tons of ore. Hence, Division Codelco Norte developed the scoping engineering for a large underground panel caving operation, similar to El Teniente mine. This project considers the exploitation of a 2500 m 300 m footprint, with three 250 m lifts. The plan considers to initiate the construction in the year 2009, to begin the production in the year 2015 and achieve a production rate of 45 million tons per year in the year 2021. A large-scale transition from open pit to underground mining like this one presents three main challenges: (1) to include the geotechnical aspects relevant for mine design and mine planning, (2) to define the proper surface and underground infrastructure, and (3) to fulfil the project deadlines and to achieve the production targets. This paper summarizes this transition project and discusses these three main challenges.

Jan 1, 2006

By Ruddle R. W.

Magnetite occurs in the reverberatory furnaces, blast furnace and converter (a) as the result of its presence in the materials charged, and (b) as the result of oxidation of the FeS in the charge in the absence of sufficient SiO2 to slag the FeO as it is produced and thus prevent its subsequent further oxidation. Magnetite is reduced by FeS according to FeS+3Fe3O4=10FeO+SO2 and similar reactions. This reaction is markedly affected by temperature and does not proceed to any important extent below about 1200°C. To ensure comparative freedom from magnetite it is therefore necessary to raise the temperature of the furnace to the highest practicable figure and to use plenty of siliceous flux. Since the maximum operating temperature is likely to be limited by the resistance of the refractories to attack by the slag, investigation of the factors affecting this attack should be helpful. It is reasonable to suppose that the formation of magnetite might be minimized by ensuring intimate admixture of matte and slag during conversion so that silica is readily available for combination with ferrous oxide as the latter is formed. The literature gives no clue to the importance of this factor and some experimental work on this aspect might be fruitful

Jan 1, 1953

By L. Nahai

THE OUTPUT ff the mineral industry in 1964 in both non-Communist and Communist Europe showed an upward trend for most countries in keeping with the higher index of overall industrial production. Comparable indexes of mineral industry production for non-Communist and Communist Europe (including the U.S.S.R. in Asia) are not available, primarily because the U.S.S.R. does not report details of its industrial production by industrial sectors. However, available data both in the form of index numbers on production published by the United Nations and based on data as reported to the United Nations by the various countries, and actual production data for selected major commodities published by the various European countries reflect generally expanded output by both the extractive sector and the processing sector of the mineral industry in most of the 26 nations of Europe.

Jan 1, 1966

By G. E. Johnson

E. D. HYMAN*—How much sorting of scrap is done ? G. E. JOHNSON (author's reply)—We do practically no sorting. We charge "run of mine" scrap to the furnace. The unmeltables, mostly iron, are in such demand today that there is no difficulty in disposing of them. It may soon be desirable to sort out from the unmeltables as much of the brass as possible. J. J. BRUGMAN†—We have somewhat similar problems in the secondary aluminum business. What is your method of removing the unmelted material from the furnaces? Why have you such an apparently small space in which to charge your materials? Do you find that you have to seal that opening, or can you have it open and continuously charge at one end and pull out the other ? G. E. JOHNSON—Our means of melting scrap is efficient only to the extent that we use the waste heat from the vaporizing chamber to do the job. It is a batch process. We open the charge door and place the scrap on the hearth by hand shoveling. The door is then closed during the melting down period. After the melting is complete, the opposite door is opened and the unmeltables are raked out. The doors are approximately 3½ X 4½ ft and are not sealed during the process only closed. They are nominally tight. Some metal is oxidized in the process. We have visualized a means of conveying the materials through this melting unit with the metals that are melted trickling out during its travel. T. H. WELDON‡—Mr. Johnson, in line with the last question, is it necessary to seal the furnace between the melting down and the vaporizing unit, or have you got an inverted syphon in the bottom of the chamber? G. E. JOHNSON—That was one of the first things we encountered. We had to have a sealed opening, and it is a molten metal seal. You have indirectly asked me another question, which was: "Do you have to seal up the melting unit?" I would say we should exclude as much air as possible, although we are not too efficient in doing that. We allow the melting unit doors to be open when we charge and when we remove unmeltables. You can readily see that that would lead to the idea of having a controlled atmosphere in the melting unit, and I think this would do a more efficient job of melting the scrap. T. H. WELDON—How often do you charge the furnace? G. E. JOHNSON—We charge the melting unit, and rake out the unmeltables, about every hour. H. R. HANLEY*—Are any provisions made for controlling the rate of oxidation for the production of various size particles for certain characteristics of the zinc oxide product? G. E. JOHNSON—Yes, there are many. You are getting pretty much into the fine points of zinc oxide manufacture. Some of us still think we have something to learn about that. In general, this muffle furnace as I have described it to you produces a rounded particle of zinc oxide which is generally formed by a rapid oxidation of the zinc vapor, followed by rapid cooling. We have gone to the other extreme in some of our experiments. We have changed the furnace to produce a type of zinc oxide, such as we thought was peculiar to American process zinc oxide, by controlling the temperature at the point of oxidation and maintaining that temperature for a much longer period of time than we do when we make the rounded shape. There are other relationships that this furnace readily provides. One of the important factors is the ratio of air to zinc vapors. We can vary that by varying the air supply to the baghouse, or vary the rate at which we are vaporizing the zinc by the simple expedient of regulating the temperature over the carborundum arch. We have a number of variables that permit us to produce all of the grades of French process zinc oxide from lead-free up through the highest grades of seal oxides. There are many controls that we can apply to the operation. What I have said is but a brief condensation. K. MORGAN*—Can Mr. Johnson give us some idea of the fuel consumption of the furnace ? How much oil does he use per ton of zinc distilled? I am also interested to know what sort of heat transmission he gets through the arch? What is the thickness of the tiles used to construct the arch? Some time ago we built a small furnace for a different purpose, using a carborundum arch, and we found that the reflectivity of the molten zinc surface was so great we had to use a very high arch temperature. We found we made an improvement by having a layer of carbon on the surface of the zinc. Has Mr. Johnson had any experience on these points ? Does he make any sort of insolu-bles which he leaves in the furnace which he cannot tap out ? G. E. JOHNSON—I believe your first question was the fuel consumption. If I recall, somewhere in this paper there is a test that I quote. I believe we used 800 gal in a given period of time. Offhand I cannot translate that into tons of metal. I might also state that we have this understanding; that the carborundum arch, as the temperature becomes higher, becomes more efficient in heat transmission. As a matter of fact, I believe it is at about 2600°F or higher that the highest efficiency of heat transmission becomes available. We have calculations that I cannot quote from memory which indicate that the carborundum arch does a really very fine job for this type of furnace. Another point that we had considered was the fact that this furnace could be readily constructed so as to furnish an ideal source of heat for waste heat boilers. If a carborundum arch was used over the melting unit, we would have no zinc vapors in the gases at all— just clean combustion gases from which we would have removed some of the heat. L. P. DAVIDSON†— The insolubles

Jan 1, 1950

By Will Frampton, Rachel Salter, Zoe Baldwin, Tim Hampshire

Cementation Skanska were responsible for the design and installation of 200 linear meters of contiguous bored piled retaining wall and approximately 1300 bearing piles for a new commercial arena development in the North of England. Building new retaining walls adjacent to existing infrastructure presents numerous challenges concerning limiting disruption and potential damage to services. The retaining walls formed a partial basement meaning horizontal propping was not practicable. To provide time and cost saving to the project, Cementation Skanska developed a novel, space saving solution to traditional raking temporary propping of the retaining walls. The contiguous wall was propped in the temporary condition by perpendicular secant piled buttresses positioned to avoid the permanent works. The buttresses were constructed from existing ground level simplifying the construction sequence by negating the requirement for additional temporary works associated with conventional propping systems. This paper describes the design and construction of the buttress wall solution, considering retained heights up to 8m, with challenging ground conditions including worked coal seams. The design considered onerous deflection criteria focussing on the services running under the dual carriageway along the East of the site and complex loading conditions from the permanent propping solution resulting in a prop stiffness envelope. The paper will detail the design process for the buttress piles and contiguous piled wall, and the iterative prop stiffness approach utilising Plaxis 2D & Geosolve Wallap. This innovative approach to propping saved the project time and cost by omitting the need for additional temporary works following construction of the wall piles and allowing berms to be removed much earlier. This solution was also considered safer to operatives than raking props. Monitoring was undertaken during the excavation phase of the project and measured deflections were below those predicted during the design process, which could create efficiencies on future projects.

Oct 31, 2023

By Gordon] [Reavis

Halliburton Services and Brown & Root have developed a unique foundation system that blends oilfield and construction technologies to construct deep foundations which offer significant advantages across a variety of soil profiles. This highly efficient system is being developed to meet the construction industry's needs into the 21st Century. Based on a concept initially introduced to Halliburton Services by V.L. Schellhorn in 1987, Halliburton combined their existing cement slurry mixing and pumping technology with oilfield drilling practices and a new tool design to field test the viability of the concept. Results looked encouraging, and Halliburton asked it's sister company, Brown & Root to evaluate and further develop the process. With Brown & Root's knowledge of the construction industry, the original concept has developed into a viable and efficient foundation construction system.

Jan 1, 1993

Upon cessation of mining activity open-cast mine pits typically fill with water, forming a æpit-lakeÆ. The water in these lakes, in some instances, contains high concentrations of ædeleteriousÆ material. Containment and/or dilution typically requires an understanding of how stratification in the pit-lake will develop over a long timescale (say 100 years). Vastly different transport rates can develop due to differing hydrogeochemistry, basin morphology and climate. Numerical (computer) modelling is the most likely approach for successful prediction over long times. While lake modelling tools are available, useful numerical modelling requires improved understanding of transport in such systems because they are different to natural lakes in a number of ways. Notwithstanding the effort required to improve our understanding, the modelling provide a means of testing approaches to active management of pit-lakes.

Jan 1, 2002

Francis Drake, Bulawayo, Rhodesia, So. Africa (communication to the Secretary *):—I should like to place on record some data in addition to those given by Mr. Canby in his paper. I regret that my notes have been destroyed so that I can give no accurate measurements of the water jacket that I am about to describe. This furnace mas erected in Cerro Gordo, Inyo county, Cal., early in 1875, and I think it quite possible that it was the first applied in lead smelting. It was made of plate iron and elliptic in shape, the inner dimensions being about 54 by 42 in. by 48 in. high. The distance between the inner and outer plates was about 6 in. Tuyere holes, one at the back and two on each side, about 12 in. in diameter, were made in this, and in these were placed cast-iron water tuyeres about 16 in. long, the diameter of the blast orifice at the point being about 3 in. The height from tuyeres to feed door was about 9 ft., but the top of the charge was kept about 5 ft. above the tuyeres. There was a space of about 12 in. between the jacket and the top brick-work. This brick-work was supported by a cast-iron plate resting on four cast-iron columns. At the beginning, the jacket was lined with air-dried radial bricks, made of crushed quartz and fire-clay, as it was thought that the jacket would not stand the heat on its bare plates. After a short time the practice was altered and no lining mas put in. The jacket was closed at the top and had a steam drum connected by two pipes at the back. This steam drum was connected to the boiler in which the steam was made for driving the Baker blower, the rock breaker and the pumps. The bottom of the jacket mas also connected to the boiler. The jacket was run under boiler pressure (80 Ib.) for some time, but eventually cracks developed in the inner plate between the tuyere holes,

Jan 1, 1913

By Curtis H. Elder

In studies conducted by the Bureau of Mines, two test areas were hydraulically stimulated and exposed by mining: One in the Pittsburgh coalbed at the Vesta No. 5 mine, Washington County, Pa.; and one in the Illinois No. 6 coalbed at the Inland mine, Jefferson County, Ill. Induced fractures were contained totally within the coalbed with no adverse effect on the stability of associated rock strata. Induced fractures were vertical and were propagated normal to the direction of least residual tectonic stress. Gas production was increased fivefold to twentyfold by hydraulic stimulation.

Jan 1, 1977

By R Ratlou

Increased contamination due to sand in spiral feed has had a negative effect on the efficiency of spiral concentrators at Navigation Plant. The no. 1 seam at Kromdraai opencast, which was previously mined by underground bord and pillar methods, is now susceptible to spontaneous combustion because of air ingress into the old workings which are exposed in the opencast high wall. This posed a risk in the loss of reserves to burnt coal. As solutions, buffer blasting of the preceding cut to collapse bords and soft overburden dressing of un-collapsed bords were implemented to prevent air entering the workings. The latter remedy resulted in increased contamination due to addition of sand in Run of Mine. After evaluating alternatives, a low capital option was selected. The 110t/hr Teetered Bed Separator (TBS) has been installed, primarily to desand and upgrade the feed to the spiral concentrators. The unit indicated an upgrade with a yield increase of 0.4% during test work and is currently showing an overall plant yield increase of 0.97%.

Jan 1, 2006

By R. H. Thompson

Preliminary safe distances for blasting wiring from typical electromagnetic sources are presented. The distances are for underground coal mines and electromagnetic sources in the frequency range below 10 MHz. The distances are based on measurements performed at 3 locations in each of 3 coal mines. The measurement apparatus, measurement procedure, measurement results and the rationale used in the calculation of the safe distances are all described. The safe distances presented are dependent on the measurement results and their interpretation. More measurements are clearly necessary to establish the validity of the suggested distances.

Jan 1, 1985