Search Documents

"The Dumont deposit is a large (1066 Mt probable reserve) low grade (0.27% nickel), nickel sulphide project located in the Abitibi region 25km west of Amos, Quebec. Royal Nickel Corporation acquired the project in 2007 and has since taken the deposit through pre-feasibility. And updated, revised pre-feasibility was released in July 2012.The disseminated nickel sulphide and alloy mineralization is hosted within the serpentinized dunite subzone of the Dumont Sill; a differentiated, pervasively serpentinized, ultramafic sill of komatitic affinity. Pentlandite, heazlewoodite and awaruite are the dominant nickel-bearing, metallic phases and can be recovered by conventional methods (flotation, mag separation). Non-recoverable nickel is also present within the silicate matrix of the serpentinized dunite and is locked in serpentine (Fe and Mg-rich variants) and minor olivine.A detailed mineralogical program including 1097 QEMSCAN® samples and 4300 electron microprobe points were undertaken to increase the understanding of the nickel deportment in the various recoverable and non-recoverable phases in a spatial context across the deposit. Eighty-three (83) metallurgical tests performed under a standard procedure have linked the mineralogy to metallurgical performance. This has allowed the creation and modelling of geometallurgical domains on a block by block basis to understand the recovery variation and metallurgical performance throughout the deposit. Understanding the spatial variability of Ni deportment in recoverable and non-recoverable phases through mineralogy is the key to understanding metallurgical performance thus, unlocking the value of the Dumont deposit and other large tonnage low grade ultramafic nickel deposits."

Jan 1, 2013

By Jasper L. Stuckey

PYROPHYLLITE, first identified as soapstone,' later as agalmatolite,2 and finally as pyrophyl-lite, has been known to occur in North Carolina for more than 130 years and has been produced intermittently in commercial amounts for the past 100 years. Pyrophyllite mining, however, has become a major industry in North Carolina only during the past 25 years. North Carolina and California are the chief producing states. Current annual production averages 125,000 tons, of which slightly more than 90 pct comes from North Carolina. Distribution and Geologic Setting: All known pyrophyllite deposits in North Carolina are associated with rocks of the Carolina Slate Belt,' which is composed of a vast series of metamorphosed volcanic and sedimentary materials, occurring as two zones extending in a northeast-southwest direction across the state. The larger of these zones, lying in the central Piedmont region, varies from 8 to 50 miles wide. The smaller zone lies along the eastern edge of the Piedmont region and is partly covered by coastal plain sediments. The rocks in both zones consist of a great volcanic-sedimentary series, composed of air-laid and water-laid tuffs and breccias, lava flows, and slates. On the basis of composition, they may be classed into three groups: 1) tuffs, breccias, and lava flows of acid or rhyolitic composition; 2) tuffs, breccias, and lava flows of a basic or andesitic composition; and 3) water-laid slates composed of fine grained materials derived chiefly from the acid tuffs and breccias and

Jan 1, 1959

By J. A. Finch

"A method of sampling and presenting bubbles for imaging for use in full-size flotation cells is described. The device (bubble viewer) comprises a tube attached to a sealed glass viewing chamber. The assembly is first filled with frother-containing water (to prevent coalescence) and the tube immersed at the desired location below the froth. For a few minutes bubbles are collected in the viewer free from slurry and are readily imaged. To reduce bubble overlap and the problem of defining the plane of view, the viewing chamber has a sloped side. Bubbles rise, encounter this slope, spread into a single plane and slide up. This simple expedient virtually eliminates overlap and provides an unambiguous focus plane - the underside of the sloped glass. The bubble image is captured and processed to give size data. The bubble viewer has been employed at several concentrators on different types of flotation cells. Examples of the images are given. The impact of position in the cell and the effect of changing gas rate on bubble size are illustrated. This technique provides a sensitive measure of the effects of process variables on bubble size.INTRODUCTIONDespite the extensive use of flotation in the mineral processing industry, the methodology employed for cell design is largely based on empirical rules rather than on first principles. One of the main reasons for this state of affairs is that the local flow structures encountered in industrial-scale machines are very complex. These flow structures are difficult to simulate under the controlled conditions of the laboratory and the difficulty to solve the mathematical models that treat the randomness of such flows also mean theoretical treatment is limited. Understanding flotation cell hydrodynamics requires reliable data, which involves the implementation of measurement techniques capable of performing both at the laboratory- and the industrial-scale, In addition, it is desirable that such techniques are amenable to automation to reduce extensive manual intervention in the data collection process."

Jan 1, 2002

By B Orchard

New Zealand SteelÆs Waikato North Head mine, situated at the mouth of the Waikato River, supplies approximately 1.2 million tonnes per annum of titanomagnetite concentrate to the Glenbrook steel mill. The mine draws its fresh water supply from the Waikato River, abstracting approximately 38 000 cubic metres per day. During the concentration process of the ironsand, slimes are liberated into the plant wastewater. The plant wastewater, storm water and groundwater from the mining operation is treated and passed through settling ponds. Around 118 400 cubic metres per day of water are drawn from the recycle settling ponds for use in the concentration plant. Typically a daily average of up to 15 100 cubic metres of the treated water is discharged back to the Waikato River. Since the early 1990s significant improvements have been made to the water treatment at Waikato North Head mine and regularly the mine discharge water quality is similar or better than background river water quality.

Jan 1, 2002

By A F. Wilson

The use of stable isotopic measurements as a technique for elucidating the origin and history of the water in hydrothermal fluids is relatively new. Recent studies have emphasised the importance of meteoric water in the formation of many hydrothermal ore deposits including many epithermal gold-base metal deposits which occur in faulted volcanic terrane. Other vein-type gold ores are believed to have formed from fluids of magmatic or metamorphic origin and exhibit characteristic d180 values. These values also give information regarding temperatures and the degree of equilibrium. Preliminary oxygen data for some important gold deposits of eastern Australia are evaluated in the context of styles of mineralisation.

Jan 1, 1980

By Jewel A. G. Gomes

Green rust (GR) are layered Fe(II)-Fe(III) double hydroxides, having a pyroaurite-type structure consisting of positively charged hydroxide layers and hydrated ions in interlayers. This special feature of GR is very efficient for wastewater treatment as the pollutants are easily taken in or exchanged with the anions in the interlayers. It can be simply and cost-effectively produced by electrocoagulation (EC). Chicken processing plant (CPP) produces large amount of wastewater containing variety of readily biodegradable organic compounds, fats, and proteins. The possible re-use of properly treated CPP wastewater would be economic and environment friendly. In this study, we present our work on treatment of CPP wastewater using EC, specifically for the removal of COD. Analysis of the EC-treated water for reuse in the same plant is discussed considering the U.S.EPA regulations. Two types of EC-reactors were used for this purpose. To better understand the treatment mechanism, EC-floc was also characterized using XRD and SEM-EDS.

Jan 1, 2010

By A. E. Hall, R. N. Taylor, J. G. Taylor

The introduction of tunnel-boring machines to South African gold mines has created problems and challenges which accompany any new technique. This paper describes the experience gained in this field, especially in the design and erection of a tunnel borer and in boring and environmental conditions.

Jan 1, 1978

By T Christie

Tertiary volcanic rocks make up a significant proportion of the surficial cover rocks of New Zealand, especially in the Taupo Volcanic Zone. Industrial minerals that are associated with or derived from the volcanic rocks include: amorphous silica, allophane, bentonite, diatomite, ignimbrite building stone, illite clays, halloysite clay, obsidian, perlite, pumice, sulphur, titanomagnetite ironsand and zeolite. Of these: bentonite, ignimbrite building stone, perlite, pumice and titanomagnetite ironsand have been mined and processed for 20 to 30 years, but many of the others require further characterisation of the resource and/or development of markets.   We have compiled interim mineral deposit models for halloysite clays in rhyolite and for zeolites in altered vitric tuffs. These models include geological and mineralogical attributes, which are linked to the underlying volcanic and geothermal processes that have produced the minerals and their source volcanic rocks. Halloysite clay deposits at Matauri Bay (Northland) have formed from hydrothermal alteration and weathering of rhyolite. Clinoptilolite + mordenite zeolite deposits in the Ngakuru area (Rotorua district) have formed from hydrothermal alteration of volcanic glass in lacustrine sediments and ignimbrite. Further refinement and application of these models will result in a better understanding of the mineralogy, localisation and origin of the deposits, with consequent applications in exploration and resource assessments.

Jan 1, 2001

By T. H. Jeffers

The U.S. Bureau of Mines has developed porous beads containing immobilized biological materials for removing metal contaminants from waste waters. The beads, designated as BID-FIX beads, are prepared by blending biomass, such as sphagnum peat moss or algae, into a polymer solution and spraying the mixture into water. Laboratory studies were conducted to determine bead sorption and elution characteristics. Batch and continuous tests demonstrated that BIO-FIX beads sorbed arsenic, cadmium, lead, and other toxic metals from acid mine drainage waters collected from several sites. Selectivity for heavy and toxic metal ions over calcium and magnesium was demonstrated. The beads exhibited excellent metal sorption and handling characteristics in stirred tanks, column contactors, and a low-maintenance passive system. The sorption process was reversible, and metal ions were eluted from the beads using dilute mineral acids. Cyclic tests indicated that the beads continued to extract metal ions after repeated loading-elution cycles.

Jan 1, 1991

By G. H. Lind

New South Wales has a successful history of pillar extraction stretching back more than 60 years. Various methods of pillar extraction ranging from the rib pillar methods (such as the Wongawilli system) to the more recent pillar stripping techniques (similar to those used in the USA) are discussed in this paper. These discussions are based on the experiences of the author stemming from a recent research tour of seven underground pillar extraction operations in New South Wales as part of the Coaltech 2020 collaborative research initiative. Some operational issues of each site visited are presented before some general comments pertaining to the overall success of pillar extraction in New South Wales are discussed. Generally pillar extraction in New South Wales is on the decline in favour of longwalling. However, the pillar extraction that is conducted is done so along specific guidelines to ensure their success, and these are also discussed.

Jan 1, 2002

By P. J. Rowsell, M. D. Waller

Paper presented at a meeting on: Artificial intelligence in the minerals sector, held in Nottingham, UK, 20 April 1993. The applications of artificial intelligence systems in the upstream petroleum industry are reviewed. Particular emphasis is placed on current and potential applications in drilling engineering. Several recent advances in drilling technology have led to a large increase in the quality and volume of data available. This combined with the escalating cost, particularly of off-shore operations, is testing the traditional reliance on the skill and judgement of rig operators. AI systems offer enormous scope in enhancing and aiding the performance of these operations

Apr 1, 1994

By J. C. Johnson

Underhand mining with cemented mill tailings for backfill has proven to be a safe and effective alternative to conventional overhand mining for rockburst prone mines. The ability of the cemented sandfill to survive a rockburst shock wave without failing has been observed at mines in the Coeur d?Alene Mining District many times in the last twenty years. To better understand the dynamic loading of this commonly used support material the National Institute for Occupational Safety and Health (NIOSH) performed laboratory experiments using a split Hopkinson Pressure Bar (SHPB) to quantify the maximum stress and energy absorption of cemented mill tailings from the Galena mine. Cylindrically shaped cemented backfill specimens aged 28 days were placed in the split Hopkinson pressure bar testing apparatus and a dynamic load was applied. The measured peak dynamic compressive strength of the cemented sandfill was 10.6 MPa (1540 psi) and is approximately twice the static unconfined compressive strength (UCS) of 5.5 MPa (800 psi). These test data showed about 95% of the initial energy was reflected away from the backfill and only 5% of the energy was absorbed. This may help to explain why backfilled stopes could withstand seismic events up to 3.5 Richter magnitude (Ml). When a compressive rockburst wave impacts a stope a large amount of the stress and energy is reflected away. The reflected wave is a tensile wave which creates tensile cracks and spalling in the entire wall of the stope. The backfill supports the damaged wall rock and holds it in place. Some of the stress and energy of the rockburst is transmitted into the backfill and because the backfill is being dynamically loaded it has a strength that is twice its static value and absorbs a substantial amount of rockburst energy. Although mining in deep underground mines is an extremely hazardous occupation, the use of underhand mining with cemented backfill for static and dynamic ground control increases the safety of the workers.

May 1, 2007

By Munro P. D

Eh-pH measurements were taken on an industrial zinc reverse flotation process at Brunswick Mining and Smelting Corporation Limited. Laboratory zinc reverse flotation testwork on samples of the feed to the industrial process produced Eh-pH data which were similar to the data from the industrial process.Later, the Eh-pH data from the industrial process were compared with data from a pilot plant scale zinc reverse flotation process at Mount Isa Mines Limited. After comparison with the data from Brunswick Mining and Smelting Corporation, deficiencies in the pilot plant Eh-pH data could be recognised and corrective actions were taken for the pilot plant. A robust pilot plant zinc reverse flotation process was obtained with consistent performance at the expected level.The implications of these findings for a range of processes are also discussed.

Jan 1, 1988

By W. U. Reimold, R. Armstrong, R. G. Charlesworth

For many years rockbursts have plagued the mining industry. Although much research has gone into studying this phenomenon only a small proportion of it has been on the actual source mechanism. A study was recently carried out to compliment the previous work done on the micro-structure of these features and to compare it to the micro-structures seen on shatter cones, from meteorite impacts. Both optical and electron-microscopy were used during the study. Samples were collected from rockburst sites by the CSIR Miningtek Rockburst Investigation Unit, and from the collar of the Vredefort Impact Crater. In the optical-microscopy study, the pinnate fractures observed in previous studies were seen in the shatter cones, through all the material. In the rockburst samples, the fractures were observed only in the quartz grains. Quartz micro-crystals were present in the rockburst samples and appeared to be the product of comminution rather than crystallisation. Cataclasite was present on rockburst and shatter cone fracture surfaces. The observations of the shatter cone surfaces with the scanning electron microscope are in agreement with previous work, including the observed presence of melt features, spherules and spheroidal material. The deformation in the rockburst samples is concentrated in the quartz grains, highly complicated with brittle features like sub-conchoidal structures and step structures present. A quartz spherule was identified on one rockburst sample and rhombic-dodecahedra type micro-crystals were present and seen fracturing off quartz grains. It is clear that the rockburst and shatter cone fracture surfaces are quite different; the shatter cone deformation is equally distributed across the sample and involves plastic-deformation, while the deformation in the rockburst material is concentrated in the quartz grains and, with the exception of spherule formation, is brittle. This study agreed with the current explanation for the formation of the rhombic-dodecahedra, and disproved the possibility of it being coesite or fine-grained meta-chert. Although there is no definite evidence of the mechanism of formation of the spherule, it is believed to be the product of vaporization and condensation, and the presence of this material indicates the extreme conditions under which this event occurred.

Jan 1, 2003

By HAROLD A. TITCOMB

TOWARD the close of 1925, a British geologist, T. Landell Mills, brought to the notice of .A. Chester Beatty and selection Trust Ltd. certain mineral areas in southern Yugoslavia. Mills' data, which included rough maps and preliminary reports by' a Yugoslav engineer, Jules Draskocy, appeared interesting to Reatty, and early in 1926, I, with three British assistants, proceeded to Serbiaand commenced the investigation of several groups of ancient mine workings. They were found to be extensive and the geological conditions-schists, limestones, and andesitic intrusive-favorable for mineral deposits. At Stan Trg, on the Trepca Concession, five rniles east of Kosovska Mitrovica, an ancient filled adit was found, a shelter-hut erected, and work started in reopening this adit.

Jan 1, 1936

By K. Nassau

The Effect of tin and hydrogen on the C0 parameter of a titanium. specimens were capsule cooled in water to eliminate contamination by water. Deybe-Scherrer photograms were obtained in a 114.6 mm camera with CuKa radiation. The parameters shown in Table I and Fig. 1 were calculated from the 213 (8569°) and 302 (8173.5°) reflections? no attempt being made to correct for systematic errors. The principal difference in method of preparation of specimens between this investigation and that of Worner was the use of pickling by the latter to produce X-ray diffraction samples. The possibility that hydrogen introduced by pickling was responsible for the lower a and c-parameters was investigated with the same 80 pct HNO3- 20 pct HF solutions used by Worner. The 6 and 10 at. pct specimens, the parameters of which had already been determined, were pickled and the c-parameters obtained are also shown in Fig. 1. The a-parameters, not shown, are also diminished. The quality of the lines obtained from the unetched and etched samples was unchanged, being quite sharp in both cases. It is quite possible that if corrections for systematic error carried out that the parameters obtained for the unetched samples would approach the data of Worner. In any event, the parameters of the etched samples would be still lower. The data obtained here is evidence that hydrogen in solution has contracted the c and a -parameters. Crystallographic Angles of Calcium Tung-state (Tetragonal, c/a = 2.169) K. Nassau In connection with the preparation and orientation of single crystals of calcium tungstate (Scheelite -CaWO4), the need arose for a stereographic projection for this tetragonal material. There appear to be no tetragonal projections with a c/a ratio above that of indium1 (c/a = 1.522) in the literature. In addition to its use for calcium tungstate, such a projection might find other more general applications and is accordingly presented below. The most recent X-ray diffraction work on CaWO4 is that of Swanson, Gilfrich, and Cook,2 where a summary of previous work is also found. Lattice parameters given are: a = 5.242A, c = 11.372A, and c/a = 2.169. The material is tetragonal with space group Table I, giving angles between crystallographic planes (HKL) and (hkl), was calculated from the formula3

Jan 1, 1961

By Virgil Miller

Bureau of Mines Reports of Investigations 3244, 3245, 3246 and 3264 give data of detailed studies on smelting in the lead blast furnace handling zinciferous charges at Trail, B. C. The present paper gives more on analyses of the gases leaving the top of the charge and on accretions formed on the walls of the blast furnace. New data are presented to show the effect of the temperatures at the tuyere zone on the lead content of the slags made. The greater part of this paper, however, deals with a much debated subject, namely air used in lead blast furnaces. Original data are presented to show the effects on smelting lead 'products when air is supplied to a lead blast furnace under volume versus under pressure control.

Jan 1, 1940

By Virgil Miller

Bureau of Mines Reports of Investigations 3244, 3245, 3246 and 3264 give data of detailed studies on smelting in the lead "blast furnace handling zinciferous charges at Trail, B. C. The present paper gives more on analyses of the gases leaving the top of the charge and on accretions formed on the walls of the blast furnace. New data are presented to show the effect of the temperatures at the tuyere zone on the lead content of the slags made. The greater part of this paper, however, deals with a much debated subject, namely air used in lead blast furnaces. Original data are presented to show the effects on smelting lead 'products when air is supplied to a lead blast furnace under volume versus under pressure control.

Jan 1, 1940

By T. McCallum, C. Cooper, C. Lewis

"Following a successful solvent extraction (SX) pilot plant demonstration in 2016, CYANEX® 600 has been used commercially to recover molybdenum from concentrate leach liquor since March 2017. Consistent with the piloting results, the commercial plant has achieved expected molybdenum recovery, a significant reduction in base consumption, and a step-change improvement in physical performance. This paper highlights the optimization activities and plant performance from startup through normal operation. INTRODUCTION Historically, tertiary amines have been the most commonly used extractant for molybdenum and rhenium recovery. Tertiary amines utilize a protonation of the ligand combined with an anion exchange mechanism as proposed in equations (1-2). R3N + H+ ???R3NH + (1) 4R3NH+ + Mo8O264- ???(R3NH+)4Mo8O264- (2) In addition to the transfer of Mo and Re, the amine transfers acid and other anions to the strip liquor. The undesirable transfer of other species increases base consumption during stripping, impacting operating costs. Additionally, lower solubility of molybdenum-amine complexes create operational challenges, resulting in diminished physical performance. The presence of colloidal Si in concentrate leach liquors and the formation of Pickering Emulsions adds to the physical plant performance challenges with the amine extractant. CYANEX® 600, a phosphinic acid-based extractant, uses a cation exchange mechanism proposed by equation (3). 2(H2R2) + MoO22+ ??(HR2)2MoO2 + 2H+ (3) The cationic exchange mechanism eliminates chemical transfer of acid and other anionic impurities and avoids some of the physical challenges of the amine extractant (emulsion and 3rd phase formation). In addition, the reagent offers high selectivity for Mo over Re, which may be desirable in certain moly pressure oxidation (POX) flowsheets. Alkali base (ammonium hydroxide, sodium hydroxide, sodium carbonate, etc.) is used for molybdenum stripping. Therefore, reduction or elimination of chemical acid transfer from extract can significantly reduce base consumption in strip. Extensive laboratory and pilot plant testing was completed to evaluate the use of CYANEX® 600 for molybdenum recovery at Freeport-McMoRan’s Bagdad operation. The test work and pilot demonstration confirmed a reduction in base consumption along with improved selectivity. In addition, the evaluation highlighted a step-change improvement in physical performance over the incumbent amine extractant. The decision was made to convert the commercial operation to CYANEX® 600 in March 2017."

Jan 1, 2018

By Henry Howe

§1. FOUR ASPECTS OF FLOW in the plastic deformation of steel by overstrain, such as punching, wire-drawing, tensile rupture, etc., are: (1) The inter-granular, i.e., the relative movements of the several grains, each as a whole; (2) the intra-granular, i.e., the relative movements of the masses of ferrite or cementite and pearlite within those grains; (3) the intra-pearlitic, i.e., the relative movements of the pearlitic ferrite and cementite; and (4) the crystal unit slipping, i.e., the travel of the minute units past each other, along the slipping planes, giving rise to the slip bands of Ewing and Rosenhain. It may be objected justly that (2), (3), and (4) are in a sense "intra-granular," and that (4) is in a sense "intra-pearlitic." Hence clearness may be gained at times by calling these "Movements of the 2d, 3d, and 4th orders" respectively.

Jan 4, 1914