Search Documents

By T. M. Siew

"This paper begins with a brief discussion of the geology of the Newfoundland Zinc Mine area. The results of groundwater studies and pumping tests are then presented. It was decided that groundwater in the mine could best be controlled by conventional sump pumping and grouting. The system is fully described, as well as plans for improvements on the method. LocationThe Newfoundland Zinc Mine is located in the Great Northern Peninsula of Newfoundland, six miles northeast of Daniel's Harbour. The mine is situated at an elevation of approximately 350 feet above sea level, 5 miles farther inland , west of the long range of mountains which rise abruptly with elevations of over 2,000 feet above sea level.GeologyThe ore deposits occur in lower Ordovician carbonate rocks that form part of the stable St. Lawrence platform, which is mainly composed of (1) the lower Cambrian Labrador group, (2) the upper Cambrian to lower Ordovician St. George group, (3) the disconformity overlying Middle Ordovician limestones and shales of the Table Head formation and, (4) two overlying klippen composed of Cambrian and lower Ordovician rocks.The ore deposit is a Mississippi Valley type of the Tennessee variety, having proven are reserves of 5.3 million tons averaging 9.70/0 zinc from eleven ore zones which exist in an area of 5.5 square miles.Among these ore zones, the L zone is the major underground mining area, and is by far the largest of the known deposits. It has proven are reserves of 3.4 million tons with 11.5% zinc; this underground development has been inprogress since 1974.Stratigraphically, the orebody, which occurs about 300 feet below the disconformities between the Table Head and St. George formations, is situated in the upper St. George formationof lower Ordovician age.The upper St. George formation of the L zone is divided into three main units (Fig . I) : the underlying lower limestone the middle grey dolomite pseudo breccia unit and the overlying siliceous dolomite unit. In this area of the mine, the beds of the St. George formation dip gently west to northwest to 10 to 15 degrees. The orebody, which is generally strata controlled with a southwesterly plunge and which has the form of thin, narrow, but elongate, en-echelon ore bed s, is contained in grey dolomite pseudo breccia. Its dimensions vary from 50 to 900 feet in width and 8 to 120 feet in thickness, and the over-alllength exceed s 6,000 feet.The surficial deposit of the area is a till comprising a heterogeneous mixture of sand, gravel, cobbles and boulders, with an average depth of 20 feet."

Jan 1, 1980

By E. I. Larsen, A. S. Doty, F. R. Hensel

The alloy under discussion is a Pig. I shows results of heat-treating tests nickel-silicon bronze and is one of many on two typical nickel-silicon bronze castings age-hardening or precipitation-hardening of the type on which the observations were copper-base alloys. The hardening constituent is a nickel-silicon compound.l The quenching temperature necessary to produce hardening by a subsequent aging treatment is a function of the composition and extends from about 700°C. to 950°C.; the aging temperature range extends from 4000 to 600°C. The work carried out by the authors of this paper was confined to cast alloys having compositions within the ranges of: 1.5 to 3.00 per cent Ni; 0.4 to 0.75 per cent Sj: balance. comer. made. A quenching temperature of 750°C. produces almost as high a hardness on subsequent aging as do quenching temperatures of 850' and 900°C. Several foundries have spent years of active and intelligent effort in trying to control the casting and heat-treating variables of nickel-silicon bronzes and finally gave up the attempts because of the inconsistencies of results.2 This undesirable characteristic was not manifest in the ultimate hardness or conductivity but primarily in tensile strength and ductility, as shown in Table I. The variation in tensile properties was often much greater than that existing on the alloys

Jan 1, 1941

By A. S. Doty, E. I. Larsen, F. R. Hensel

The alloy under discussion is a Pig. I shows results of heat-treating tests nickel-silicon bronze and is one of many on two typical nickel-silicon bronze castings age-hardening or precipitation-hardening of the type on which the observations were copper-base alloys. The hardening constituent is a nickel-silicon compound.l The quenching temperature necessary to produce hardening by a subsequent aging treatment is a function of the composition and extends from about 700°C. to 950°C.; the aging temperature range extends from 4000 to 600°C. The work carried out by the authors of this paper was confined to cast alloys having compositions within the ranges of: 1.5 to 3.00 per cent Ni; 0.4 to 0.75 per cent Sj: balance. comer. made. A quenching temperature of 750°C. produces almost as high a hardness on subsequent aging as do quenching temperatures of 850' and 900°C. Several foundries have spent years of active and intelligent effort in trying to control the casting and heat-treating variables of nickel-silicon bronzes and finally gave up the attempts because of the inconsistencies of results.2 This undesirable characteristic was not manifest in the ultimate hardness or conductivity but primarily in tensile strength and ductility, as shown in Table I. The variation in tensile properties was often much greater than that existing on the alloys

Jan 1, 1941

By T. Iwanowski

Stress wave measurements and calculations are often used to make a safe determination of the bearing capacity and the integrity of driven piles. Some applications to the restoration of old buildings in the Old Town of Stockholm are referred to and especially analyses of measurements combined with simulations are discussed here.

Jan 1, 1991

By B. W. Gandrud, A. C. Richardson

"INTRODUCTION The Bankhead mine of the Cane Creek Coal Mining Co. is in the central part of Walker County, Ala., 4 miles south of Jasper. The Mary Lee bed in this part of the State yields a practically free-burning coal which is marketed as a. steam-raising and domestic fuel. As mined, the coal ordinarily contains ash-forming impurities to an extent that makes it necessary to treat the coal by some washing process before it is marketed. At present the Bank-head coal coarser than 3-1/2 inch is hand-picked and the coal finer than 3-1/2 inch is washed in two single-compartment jigsThis paper contains the result of screen-sizing and float-and-sink tests on a representative sample of the run-of-mine coal and the results of tests made to show the amount of coal liberated from impurities by crushing the coarser sizes. .This report is one of a series on the washability of Alabama coals which is being prepared by the U. S. Bureau of Mines and the University of Alabama, with the cooperation of the coal producers of Alabama.SAMPLING AT THE MINE'The Mary Lee bed at Bankhead consists of two benches separated by a rock parting which varies in thickness from place to place in the mine. The top bench has a very uniform thick-nest; throughout the workings and yields about 65.0 per cent of the output. The bottom bench varies greatly in thickness and in nary places becomes too thin to work at a. profit. The sample for the washability study was taken underground at a place which was typical of the mine as a whole. In taking the sample the working face was squared up and a representative section out from each bench. Care was taken to secure a, quantity of coal from each bench proportional to the quantity contributed to the mine output. The rock parting as gobbed in accordance with the usual mining practice. The total sample taken weighed 3 tons."

May 1, 1933

By D. Asefi

A new method to detect microstructural features such as recovery and recrystallization as well as cold rolling reduction in low carbon steels was developed based on magnetic hysteresis loop measurement. To this aim, a hysteresis loop measuring apparatus, specifically designed and assembled for plate samples was employed. It is shown that maximum field (Hmax) of hysteresis loop, measured at constant maximum flux density (Bmax) of 0.5T, is an adequatemagnetic property to monitor different stages of changing microstructures during annealing.

Oct 1, 2011

By W. R. Matizamhuka

"The consolidation of nano-sized composite materials presents a challenge using conventional hot pressing methods. Spark plasma sintering (SPS) technology has shown great promise in the successful sintering of nanoreinforced composite materials. This qualitative review seeks to impart knowledge gathered, and progress made over the years on the consolidation of nanocomposite materials using SPS technology. The review is aimed at introducing this technology to the South African science and engineering community. Emphasis is on improving the mechanical properties of structural ceramic nanocomposite materials, which over the years have shown great promise in a wide range of applications, including transport, energy, mining, and the environment. Although success has been achieved within the laboratory for research purposes, there are still great opportunities to commercialize the technology for the production of larger components with more complex shapes.IntroductionSince the pioneering work of Niihara and Nakahira (1991) over a decade ago there have been extensive attempts to harness the potential of nanostructural metals, ceramics, and composites in a number of applications (Niihara and Nakahira, 1991; Selaho et al., 1997; Sekino and Niihara, 1995; Khalil, 2012; Aalund, 2008). It is generally realized that reducing the grain size of materials to nanoscale offers a significant improvement in properties. Attempts to synthesize nanostructured compacts by conventional sintering methods have not succeeded owing to the uncontrollable high rates of grain growth driven by long dwelling times at the sintering temperatures and large powder surface areas (Sergueeva et al., 2009; Gua, Khora, and Chieng, 2004; Tang et al., 2009). Following the development of spark plasma sintering (SPS) technology, it is now possible to process nanocrystalline materials with controlled grain growth. SPS, also referred to as the field-assisted sintering technique (FAST) or pulsed electric current sintering (PECS), was developed with the aim of improving on the well-established hot pressing (HP) technology (Kessel and Hennicke, 2007;"

Jan 1, 2016

The work to be described is part of a comprehensive research on the influence of impurities on the properties of lead. The author had previously compared an electrolytic lead containing less than 0.002% total impurities with a commercial lead containing 0.008% impurities (excluding oxygen) and had shown that the former recrystallised more readily than the latter under the same conditions of cold work and annealing. This difference in properties was attributed to the difference in purity. Electrolytic lead containing only 0.0005% total impurities has been prepared and cast in vacuo. Some interesting effects have been obtained by working and annealing this lead, and by adding silver to it. The preparation of this lead, and the effects obtained thereon, are described in this paper. Thepaper is divided into the following sections:(I) Preparation of electrolytic lead.(II) Vacuum Casting.(III) Effect of Cold, Work and Annealing on two Electrolytic Leads, having 0.002% and 0.0005% Total Impurities respectively.1 Research Fellow, Dept. of Metallurgy, University of Melbourne.2 Proc. Aust. lnst. Min. Met., 1932, 87, 145.

Jan 1, 1934

By John D. Sullivan, Alfred P. Towne

"In copper percolation-leaching plants the ore is usually crushed to a maximum size of about three-eighths inch. Ordinarily an ore is crushed as finely as feasible since the rate of extraction of copper is increased with decreasing size of particles owing to the greater surface exposed and. the shorter path required for solutions to come into contact with the minerals to be dissolved. However, greater degree of crushing also increases the amount of fines. When ores are charged into leaching vats the coarse and fine material tend to segregate, resulting in channeling of solutions and leaving the areas where fines predominate only partly leached. An improvement in the method of charging the ore into vats that would minimize the deleterious effects of the segregations of fines would increase the percentage extraction of copper.The Inspiration Consolidated Copper Co.4 recently installed classifiers to remove the primary slimes from the ore, before charging it into the leaching vats. This necessitates a separate agitation treatment for the slimes.Recent publications5 of the bureau have shown the advantages of agglomeration followed by trickle leaching to extract copper from concentrator tailings. It was shown that when equal parts of ore crushed to about 1/4-inch size and concentrator tailings were agglomerated with approximately 10 per cent of moisture, either in the form of water or leaching solution, and the mass was charred into a leaching vat the ore could be treated successfully by open-drainage trickle leaching. Even with 30 or 35 per cent of minus 200-mesh material present the ore could be leached, if it was not flooded with solution.The results obtained in agglomerating ores and slimes suggested the possible advantages to be gained by wetting the crushed ore for standard percolation-leaching plants before charging it into the vats. Wetting the ore whould make the fine material and slime cohere to the larger pieces of ore thus tend to prevent segregation when the ore is charged into the vats. The bureau, at its southwest Experiment Station and in cooperation with the Department of Mining and University of Arizona, Tucson Ariz., therefore made a study to work: out A way in which slimes could be handled in percolation leaching. The study showed that the method of charging ore into the leaching vats governed the distribution the fines and consequently the rate extraction of copper. The results of the study reported in this paper."

Feb 1, 1931

By D. Imeson, T. Grammatikopoulos, M. Aghamirian, M. Oliazadeh

"More than 70% of potash is produced worldwide by froth flotation. Flotation of potash was developed in the early 1930s. Amines are widely used for flotation of sylvite (KCl) from halite (NaCl) and insoluble materials such as clays. Amine collector is also absorbed by clays. Therefore, clays are usually separated by scrubbing and de-sliming prior to flotation. Alternatively, slimes can be floated ahead of potash flotation. Flotation recoveries of sylvite are commonly in the range of 85%, while losses can occur in slimes, flotation tailings and make-up of process brine. Ores containing free coarse-grained sylvite are generally screened, whereas both fine and coarse fractions are conditioned and floated separately. The unique features of potash flotation include solubility of sylvite in water, the size of particles floated and fast kinetics. Particles up to 2.3 mm can be floated and about 50% of flotation feed can be removed in the rougher stage in few minutes. The main challenges in potash flotation are the recovery of potash from slimes, flotation efficiency in the presence of carnallite and recovery of coarse potash grains. A review of potash flotation shows that there is still room for improvement in both coarse and fine potash flotation. The present paper reviews the most significant flotation parameters including reagent type and dosage, flotation circuits, flotation equipment size and new developments in potash flotation. The latter include new reagents, flotation technologies (Hydrofloat, Jameson and column cells) larger flotation cells and slimes flotation.INTRODUCTION Potash is the common industrial term for potassium in various chemical combinations and minerals soluble in water. About 90% of potash produced worldwide is used as agricultural fertilizers. Flotation is the main treatment process of sylvinite (KCl-NaCl) ores for recovery of sylvite (KCl). Potash concentrate should contain a minimum of 95% KCl and be relatively free from 0.2 mm KCl fines. The flotation process for beneficiation of potash ores was developed in United States and Russia concurrently in the early 1930s. In 1934, Potash Corporation of America applied flotation process in a commercial scale (Tippin R.B. and Huiatt J.L). In the initial application, halite (NaCl) was selectively floated by employing lead chloride as an activator and soap as collector. The sylvite concentrate was reported in the cell underflow."

Jan 1, 2012

By A. B. Hooker, L. C. IlsLey

Explosives have been fired electrically for several decades. Mountains have been tunneled, deep shafts sunk, extensive coal and metal mine workings excavated and, in times of war, railroads, buildings, bridges, and fortifications have been destroyed by means of electrically fired explosives. Modern engineering depends so much on explosives that their safe and efficient handling and especially their detonation are of prime importance to all those connected with the use of explosive agents. Electric shot-firing is only one method of igniting explosives, but it is rapidly spreading and because of certain inherent safety features should be encouraged. Data collected by the Bureau of Mines indicate that in the United States a large percentage of the blasting in quarries, shafts,· and tunnels, and from 15 to 25 per cent of the blasts in mining operations, are set off electrically. The Bureau of Mines is interested in electric shot-firing because of its use in mining, and especially because electric methods, when properly applied, are undoubtedly safer than other methods commonly used. Electrical problems of many kinds must be solved in dealing with the various phases of electric shot-firing. Success in using an electric detonator is closely linked with the resistance of its bridge, the resistance of its leg wires, and the insulation of its current-carrying parts. The proper layout of a circuit where a number of shots are to be fired simultaneously depends not only on the types of detonators that are used and their arrangement and interconnections, but also on the size and insulation of the wire leading back to the source of power, and even on the source of power itself. Various types of electric shot-firing machines have been developed, and these offer still another field for study. In investigations of electric detonators and electric blasting equipment, the oscillograph is valuable because it can record electrical activity over very short intervals of time. By its use more complete information about electrical performance can be obtained than by any other means.

Jan 1, 1926

The only simple sulphide mineral of antimony of importance is stibnite, SbS3, containing 71·8% antimony when pure. It is lead-grey, has a densityof 4·5 to 4·6 and melts at 546°C. It is both friable and sectile (Hardness 2 on Moh's scale) and, as a result, slimes very readily during milling.It is commonly associated with pyrite and arsenopyrite other minerals occurring with stibnite in minor quantities are chalcopyrite, galena, and scheelite. The latter mineral occurs in sufficient quantity at the Yellow Pine Mine, Stibnfte, Idaho, to justify the production of a scheelite concentrate.Stibnite mayor may not contain gold. Other minerals such as pyrite or arsenopyrite may contain gold. At Wiluna at the main mine nearly all the gold is asociated with arsenopyrite the stibnite being almost free from gold, whilst at the Moonlight Mine both arsenopyrite and stibnite carry gold.The mineral, tetrahedrite, which is a complex sulphide of copper and antimony; must also be considered an economic source of these two metals.Part of the copper may be replaced by iron, zinc; silver; or mercury, whilst part of the antimony is often replaced by arsenic.CLASSIFICATION OF ANTIMONIAL GOLD ORESFor the purposes of this paper antimonial gold ores may be conveniently classified as follows: CLASS 1. Ores from which a satisfactory gold extraction may be obtained by fine grinding, followed by cyanidation and which contain insufficient antimony to justify tIie production of an antimonial concentrate.CLASS 2. (a) Ores in which a satisfactory gold extraction may be obtained by straight cyanidation, but which contain sufficient antimony to justify the production of an antimonial concentrate.CLASS 2. (b) Ores from which the gold extraction by straight cyanidation is unsatisfactory. This type of ore requires the production of an antimonial concentrate for reasons which will be considered later.In deciding whether an ore belongs to class 1 or 2 (a) it should be remembered that the normal price of star antimony is about £1.00 sterling per ton and that the value of each 1% of antimony recoverable as metal is worth about £1 per ton.The antimony content of antimonial gold ores is liable to be considerably...

Jan 1, 1944

By Frank Firmstone

. In the early decades of the past century the method of starting iron blast-furnaces by " scatlolding-down" seems to have been in universal use for coke-furnaces and, at least in this country, for charcoal-furnaces also. It was likewise used at some of the early anthracite-furnaces, as is stated in the important " Reminiscences" printed by the late Samuel Thomas.' It had been generally superseded in Great Britain as early as 1850, by some variations of the plan now used, and was rarely used when Percy wrote.2 On the Continent it was still followed ill the 60's; and was elaborately described by Valerius in 1852. I have never read any statement as to when and by whom " scaffolding " was first dispensed with, but the following extracts from journals of my father seem to fix an authentic date for an instance in this country: " [Pittsburg] July 12, 1838.—Went with Major Wade to his foundry,etc., and he gave me a letter to D. Tyler, Esq., Farrandsville, Agent Boston Coke & Iron Co." " [Lockhaven, Pa.] July 18, 1838.—Heard there was a flat-boat going to take some gentlemen up to Farrandsville. Got on boat and to Farrandsville, 5 or 6 miles, in 1 hr. 30 min. Dined, and then delivered my letter to Ma Tyler, who showed me much attention, and everything belonging to the furnace, and had the water turned on the wheel that I might see the blowing-cylinders at work. There are two cylinders, 6-ft. stroke, -56 in. in diameter, but they find that one makes more than enough blast for the furnace. The furnace has 16-ft. boshes, 7-ft. tunnel-head, and is 47 ft. high, 3 tuyeres, and 3 heating-ovens [hot blast-ovens]. A

Jan 1, 1908

By D. S. Burgess

This report summarizes the incidents that preceded the December 9, 1970, propane-air explosion in Port Hudson, Mo., and then attempts to establish the nature of the explosion from the ensuing events. Special emphasis is given to possible ignition sources, the distribution of flammable vapors, and the analysis of blast damage. Both near-and far-field damage indicated that this explosion may be attributed to the detonation of propane in air with an energy release equivalent to that from about 50 tons of detonating TNT.

Jan 1, 1973

The Geological Resource Map of New Zealand (GERM) is a computerised inventory of aggregate, mineral, coal, petroleum and thermal water occurrences, containing summary information on location, production, geology, and geochemistry. The types of occurrences include quarries, mines, gold dredges, wells, outcrops, seeps, springs, and fields. The file contains entries for about 10,300 sites and is used to produce tables of data and maps at any scale, for single or multiple commodities. The published format is the New Zealand 'Geological Survey map series Geological Resource Map of New Zealand 1:250 000'. Seventeen of the 27 map sheets covering New Zealand were published by August 1991, with three more close to publication.

Jan 1, 1991

By Sadettin Bagdatli, Ali Kahriman, Umit Ozer, Alper Celtikci, Yucel Karakus

Due to population growth and rapid urbanization in Turkey, the need for the construction of residential units, transportation and infrastructure facilities has become increasingly more pressing. Since rock units encountered in the surface and underground in the construction of the subway, infrastructure and housing facilities, it is a necessity to use blast excavation methods. In recent years, large housing construction projects have been carried out especially in Turkish metropolitan areas, involving foundation excavations giving rise to great amounts of earthmoving. Since rock units encountered during foundation excavations are usually hard and solid, excavation with conventional machinery proves to be inadequate and unproductive, hence the necessity for the application of blasting technology.

Jan 1, 2014

Deep level block caving as a mining method is becoming more popular due to the fact that it is the lowest cost per ton underground extraction system. However, many block caves do not achieve their full potential due to draw horizon instability. In this paper five design rules are given to overcome this problem. The design rules described are applicable for slusher and trackless block caves where the operational depths exceed 500 metres.

Jan 1, 1999

By R. K. Agarwal

In this paper, a new technique developed to analyze two-dimensional nonhomogeneous models is described. A simple three-layered medium with a circular hole centrally located in the intermediate layer is considered. The layered sheet is loaded uniaxially perpendicular to the stratification. The Young's modulus of the intermediate layer is lower than that of the outer layers. The stress distribution around the circular hole in a stratified medium is significantly different when compared to the case of a continuous homogeneous medium. The distribution depends upon the ratio of the height of the intermediate layer and the hole diameter. A comparison of stress distribution and procedures for preparation and testing of the model are given. The potential of the technique is outlined. In the process of applying the techniques of stress analysis to problems of rock mechanics, the recent discernible trend has been to postulate highly idealized models of physical situations. As new techniques have been developed, more complicated models have been conceived to simulate mote accurately the physical environment to which the analysis results are eventually applied. In this investigation, a new technique is developed to analyze two-dimensional nonhomogeneous models. The technique is used to determine the stress concentration around a circular hole in a soft material overlain and underlain by a hard material. In mining practice, such situations arise commonly in coal deposits and frequently in bedded or vein-type metallic mineral deposits. DEFINITION OF THE PROBLEM A plate, consisting of three layers with a circular hole in the intermediate layer, is loaded uniaxially, Fig. 1. The variable in the experimental investigation is the height of the intermediate layer, H. The diameter of the hole, D, is kept constant. The stress concentration factors around the periphery of the hole, for various values of H/D, are evaluated using the technique of photoelasticity, Table I. TECHNIQUE OF EXPLORATION Photoelastic analyses of composite models have hitherto been limited to the study of lap and butt joints between glued metals and dissimilar materials.1-3 In mining, Haber and Oudenhoven used composite models to study the stress distribution around a circular hole in two-layered media and the behavior of elastic liners in shallow underground openings.4-5 They used the stress freezing technique devised by Dally et a1.6 The procedure used in this investigation is outlined below: Casting of Layer A: Flat sheets of plastic were cast in a silicon-coated mold using Araldite 502 with hardener 951 in the ratio of 100:8 by weight. After

Jan 1, 1969

By Philippe Caudal

This paper presents a case study in which a slope failure was observed on the west wall of the LAB Chrysotile mine in the vicinity of the main ramp in January 2010. Airborne LiDAR results were used to evaluate slope geometry before and after the failure occurred. Back analysis of the failure was performed to assess rock mass properties at the slope scale using various numerical techniques: limit equilibrium, finite elements and fracture networks. The various approaches correlated well with field observations.

Aug 1, 2013

CONTENTS PAGE HESSE, A. W,-Safeguarding Coal-mining Operations against Danger from Oil and Gas Wells. Discussed by A. W. Hesse, T. G. Fear, George H. Ashley, George S. Rice, W. E. Fohl, R. V. Norris, S. A. Taylor, F. B. Tough, C. W. Gibbs, A. Hurlburt, S. W. Meals 1 DAWSON, THOS. W.-Belt Conveying of Coal at H. C. Frick Coke Company Mines. Discussed by F. F. Jorgensen, Thos. W. Dawson, Graham Bright, A. W. Hesse 13 OTTO, HENRY H.-Ultimate Recovery from Anthracite Coal Beds. Discussed by R. V. Norris, S. A. Taylor, Henry H. Otto, Douglas Bunting, Graham Bright, Howard N. Eavenson, J. B. Warriner 15 HOSLER, Rush N.-Schedule Rating Coal Mines in Pennsylvania for Compensation Insurance Rates. Discussed by E. A. Holbrook, W. W. Adams 17 ARCHBALD, HUGH.-Application of Gaussian Curve to Mining Industry. Discussed by Donald A. Laird, T. T. Read 19 ASH, SIMON H.-System of Coal Mining in Western Washington. Discussed by Eli T. Conner, Simon H. Ash 21 MILLER, J. S.-Method of Mining a Steeply Pitching Anthracite Vein by Successive Skips. Discussed by Eli T. Conner, J. S. Miller, J. B. Warriner 22 HARRINGTON, GEORGE B.-New Orient, an Unusual Coal Mine. Discussed" by George S. Rice, Eli T. Conner, John A. Garcia, George B. Harrington, F. F. Jorgensen, Graham Bright, W. M. Hoen, George N. Simpson, W. C. Adams, R. W. McNeill, Chas. C. Whaley, Carl Scholz, E. T. Gott, Andrews Allen 23 PERROTT, G. ST. J.-Properties of Liquid-oxygen Explosives. Discussed by George S. Rice 48 Safeguarding Coal-mining Operations against Danger from Oil and Gas Wells Discussion of the paper of A. W. HESSE, presented at the New York Meeting, Feb-ruary, 1925, and issued, as Paper No. 1412-F, with MINING AND METALLURGY, February, 1925. A. W. HESSE.-The well under investigation, No. 101, Fig. 2, was started about Sept. 5, 1921, and drilled-in in November. The first hole was started with a 13-in. bit and reached the Pittsburgh coal at a depth of 563 ft.; at 602 ft. the 10-in. casing was run in and the well was continued with a 10-in. bit and 1400 ft. of 8-in. casing was put in. It was then continued to a depth of 1770 ft. and 6-in. casing put in; then continued to a depth of 2555 ft. where the gas was struck. As the well produced only about 100,000 cu. ft. per day. 2-in. tubing was used to conduct the

Jan 6, 1925