Search Documents

By N M. Caira

The North Arm of Sulawesi hosts numerous gold and base metal occurrences. Compilation and analysis of geological, tectonic, geochemical and isotopic age date data collected over the past six years on the central part of this region have resulted in the definition of 184 prospects and mineral occurrences of various styles occurring in diverse geological settings representing varying tectonic environments and erosional levels. Mineralisation of the following styles have been recognised: porphyry Cu-Au; porphyry-related gold and base metal veins; high-sulphidation Cu-Au-As; low-sulphidation epithermal Au; hydrothermal breccias; and sediment-hosted Au mineralisation. Clusters of occurrences/prospects form mineralised districts representative of magmatic systems with characteristics determined by the tectonic environment prevailing during formation and the subsequent level of exposure by erosion. Distinctly different Miocene and Pliocene porphyry systems are now recognised whilst most of the remaining epithermal mineralisation is thought to be Pliocene or later. The central North Arm of Sulawesi is composed of a Miocene magmatic island arc that is built on an Early Tertiary basement of predominantly oceanic basaltic rocks and overprinted by a Pliocene magmatic arc. A structural fabric dominated by SSE arc-normal and ESE arc-parallel faults was established during the Miocene under a dextral wrench regime and intersections of these major fault sets are favoured sites for Miocene porphyry Cu-Au mineralisation. Strong dextral tension caused by the collision of the Sula Platform, at the close of the Miocene, led to arc-parallel rifting. Sinistral reactivation of the major Miocene structures in the Pliocene led to further rifting, and ENE-dilation. Pliocene intrusions and related mineralisation exploit these dilatant settings. Miocene porphyry Cu-Au mineralisation occurs where late-Miocene quartz diorite stocks have intruded the margins of earlier Miocene plutons of intermediate composition. Porphyry centres have associated peripheral base metal veins, and skarns. Overprinting of porphyry vein sets by epithermal veins is common. Sediment-hosted gold mineralisation occurs in calcareous sediments associated with the Miocene arc. Remnants of the Pliocene volcanic arc, comprised of dacite volcanics, intrusions and voluminous pyroclastics, dominate the south coast and host porphyry Cu-Au, high sulphidation Cu-Au-As deposits, low-sulphidation epithermal Au veins and disseminated gold mineralisation. In some prospects, mineralised sinters are preserved adjacent to vein systems and deeper mineralised stockworks. Diatremes are common and large caldera structures have been identified. Pliocene stocks and porphyry dyke swarms penetrate the main central and northern parts of the Miocene- arc introducing additional porphyry Cu-Au, base metal hydrothermal breccias and low-sulphidation gold veins. Rapid uplift and erosion has resulted in a highly variable preservation of styles of mineralisation adding further diversity within the mineralised districts and telescoping within deposits.

Jan 1, 1999

The design of excavations in high displacement mining environments requires consideration of both the load and displacement capacity of the ground reinforcement and support systems. This paper is a case study on the design of point anchored rebar bolts using laboratory tests and field trials at the Ridgeway Deeps block cave. A laboratory testing program was carried out to measure the mechanical properties of the Strata Control Systems R27 Secura resin bolt which is currently being installed on the extraction and undercut level at the Ridgeway Deeps block cave. The aim was to quantify elastic, plastic and energy parameters for various bolt, mesh and plate systems. Experiments were performed on bar segments, bolt/plate systems, and bolt/plate/mesh/resin systems. The mechanical properties were calculated from tensile tests with a 500 kN Avery machine. Load-displacement data was collected from four different testing configurations. The laboratory results are compared with underground measurements and observations of bolt performance.

Nov 25, 2010

By R A. Lynch, D A. Malovichko

The implementation of routine real-time micro-seismic monitoring of open pit mine slopes has been discussed. Some examples of seismic arrays have been given, and a recommendation of suitable seismic sensors made. Unfortunately near-surface sensors are required for good location accuracy, and the effects of reflection, mode conversion and surface waves must be accepted and compensated for during processing of the seismograms. It makes sense that mining at the base of a slope and levels of seismic activity within the slope should be related, and this is confirmed using both 2002-2003 and 2005 seismic data recorded at Navachab mine. An example of how seismic data can be used to gain information about seismically active geological structures has been described. The removal of broken rock, and not blasting nor the breaking of supporting rock, has been found to cause slope micro-seismicity. While the standard Brune source model is suitable for some 20% of the seismic events, unreasonable results are obtained for the rest. A moment tensor inversion has been performed after S-wave splitting and surface effects have been filtered out. This approach confirms a predominantly shear mechanism for a typical high frequency source.

Jan 1, 2006

By S. P. Singh

Drifts are an integral component of underground mining. They provide access for men and material, means for transporting ore and rock and serve as air passageways. In view of their importance on the overall safety, economy and productivity of mines, empirical guidelines for controlled blasting design in drifts have been developed in this study. The application of the proposed concept was described by generating blast hole patterns for a mine with the help of a computer program. The mechanism of blast damage and the need for controlled blasting to alleviate ground control problems in underground mines have been outlined in this paper. The economic analysis between normal-and controlled blasting was performed based on the information from an operating mine. In addition, the review of drift blasting practices and problems in Canadian mines was also carried out in this study.

Jan 1, 1990

By Chang Wei, Zhigan Deng, Minting Li, Cunxiong Li, Gang Fan, Xingbin Li

Iron precipitation occupies a vital position in the metallurgy industry, especially for treating iron-bearing sphalerite in hydrometallurgical processes. This paper emphasizes techniques for removing iron from high-iron sphalerite via hematite precipitation, and describes the results of research performed to examine ferrous oxydrolysis and precipitation. The behavior and mechanism of conversion between the iron phase and hematite residue at elevated temperature under pressure is ascertained by investigating the dissolving characteristic and thermodynamics stable area of hematite at sulfate system. The results show hematite precipitation went through the process of crystallization, dissolve, oxidation and precipitation of ferrous sulfate, and the overall iron precipitation was determined to be controlled by the rate of ferric sulphate hydrolysis rather than the oxidation of ferrous sulphate or the re-dissolution of ferrous sulphate crystals, or the transformation of basic ferric sulphate.

Mar 1, 2018

The Effect of Ionic Strength of Plant Water on Valuable Mineral and Gangue Recovery in a Platinum Bearing Ore from the Merensky Reef

Sep 13, 2010

By F. Samimi Namin

During the process of developing surface or underground mines, some sites are considered for dumping of surface soils, while others are applied to reclaiming surface and waste disposal. For each kind of overburden, whether it be waste rock, low-grade material, or process tails, a separate storage site is considered so that it becomes possible to transport or recover the overburden separately. Decision-making must be completed by means of a selection process which takes into account the best methods of alternative sets in order to achieve these goals. This decision- making involves many parameters that are inter-related in that changes in some parameters affect the others. There are many methods of decision-making, however, Fuzzy Multi-attribute Decision-making (FMADM) and its functions are studied in this paper. The advantages of this method lies in its theoretical background, formulation, revising capability, unlimited alternatives, and consideration of the counteraction of the different parameters upon one another.

Jan 1, 2007

By D. Vogt

A brief summary of the propagation characteristics of rock provides the necessary understanding to design effective radar surveys. Measurements of the electrical properties of the major Bushveld platinum-bearing horizons and their host rocks show that radar is an excellent tool for both short -and longer-range mapping. Experimental work confirms the performance predictions. High frequency, 500 MHz ground-penetrating radar (GPR) is a first-rate tool for mapping features in the hangingwall of the orebody, locally known as a ?reef?, for the purposes of determining hangingwall stability. The triplet chromitites above the UG2 have been clearly mapped, as has the Leader Seam above the UG2. Borehole radar at lower frequencies has been used over longer ranges to map reef elevation. Potholes in the UG2 are clearly distinguished in range and elevation to within metre accuracy. The nature of the slump in the various footwall horizons is also apparent. In future, as GPR is routinely applied, it is likely to become used for other purposes. Borehole radar is being developed to operate at higher frequencies, which will allow it to be deployed from boreholes that are within 5 m of the target horizon. Keywords: GPR, borehole radar, Bushveld Complex, UG2, Merensky, pothole, triplet

Jan 1, 2005

By Rob Jameson

"The demand for commercial and residential construction has continued to evolve across the United States over the last decade. Our markets demand larger, deeper and inherently more complex structures, located within increasingly constrained urban locations and with challenging geotechnical conditions. As project demands incrementally escalate, specialty contractors are continuously challenged to extend their state of practice. Development in the size and capabilities of construction equipment, tooling, techniques, monitoring and verification systems over the last decade has consistently allowed contractors to build larger and deeper. For support of excavation (SOE), in addition to scale, selection of the most appropriate system has been a key to success in the most challenging ground conditions. This selection process is based on sound engineering and construction practice, and also prior experience, both positive and negative. Ultimately many Owners have chosen to manage their risk of SOE construction through design-build contracts, which allows specialty constructors to optimize the balance of cost, schedule, scope and associated risk based on their local expertise. Successful implementation of a design-build methodology begins long before a contractor is selected, with identification of key project requirements and risk factors during the feasibility studies and design development phases. In these early stages of the project development, advice and budgets are frequently solicited from Specialty Contractors. The Owner, Construction Manager and Consulting Team will filter this input from multiple sources to provide their specific recommendations, develop construction documents and select the appropriate form of contracting. Only in the final stages, after award of a Design-Build Subcontract, can the successful specialty contractor directly influence risk management approach on the project. A case study is presented from Block 9 in San Francisco’s Transbay District. This project demonstrates the incremental identification, assignment and mitigation of construction risk through the planning and design build process for SOE on the deepest planned excavation in San Francisco.INTRODUCTIONThe mature urban development market in United States results in high demand for complex Support of Excavation (SOE) schemes on constrained sites. The Design-Build approach can be applied to increasingly difficult SOE challenges, combining regional specialty subcontractor knowledge and experience in order to optimize solutions for cost and schedule. The most successful applications will involve early engagement of shoring subcontractors within the project teams, during feasibility and design development stages, in order to identify key scope and risk issues, and their potential solutions. Throughout the project development, it is important to reasonably assign responsibility for construction risks amongst the project stakeholders who are best able to control them.This paper presents a case history for San Francisco’s Block 9, a well-planned and successfully executed design-build SOE project in San Francisco’s Transbay Redevelopment area. Throughout the 4 year period from the Developers initial proposal to the Redevelopment agency, through completion of excavation down to subgrade, the project team developed a series of increasingly refined SOE schemes, with corresponding scope definition and cost and schedule estimates. This program relied on early identification of key challenges and risks for the project, and evolved through multiple phases of proposals as first the General Contractor (GC) and then Specialty Shoring Subcontractor were engaged for the project. The scheme, cost and schedule refinements continued throughout construction in order to accommodate unanticipated conditions and events as they unfolded."

Jan 1, 2017

By Dimitri Frantzos, Stewart Thompson, Ed Skiba, Hans Tammemagi

On behalf of Acres International we would like to thank Frank Chiappetta of Blasting Analysis International for inviting our organization to participate in this state-of-the-art course on blasting analysis techniques.

Jan 1, 1989

By C. S. Matthews, G. L. Stegemeier

In one field in South Texas, approximately 72 per cent of the pressure build-up results show a characteris-i.rtic "hump" (i.e., the pressure builds up and then falls off) which makes interpretation by. standard methods impossible Correlation of size and time of hump with formation permeability. well productivitv index, and method of completion led to the tentativc, conclusion that the humps were caused by segregation of gas and oil in the wellbore after closing-in"'. This conclusion was confirmed by performance of simple laboratory bubble-rise experiments, by theoretical bubble-rise time calculations, and by a detailed calculation of PVT behavior in the well of a particular well Oil which accurate Surface and bottom-hole pressure measure-ments were untile. The hump behavior has since been found to occur in many other fields. The cause, however, is not the mine in all cases. In some of these the hump is trace-ahie to leaks in the tnbing which allow influx from the annulus after closing-in. In other cases the hump is traceable to leaks in the device separating pay horizons in dually completed wells. It is concluded that the recording of both surface and bottom-hole pressures is desirable in wells which show an anomalous build-up behavior. A number of field examples is discussed where use of both sets of measurements enables the cause for anomalous behavior to he found, (and a reasonable interpreation of bottom-hole pressure to be made. INTRODUCTION Theoretically the pressure build-up in an infinite reser-voir should be a linear function of In [(t + at)/nere t is the production time and At a the closed-in time. Some of the variations from this behavior arc well known, such as the curved portion immediately after shut-in which results from after-production and skin effect, and the flattened end portion which results from boundary effects in a limited reservoir. The effect of stratified producing zones and irregular geometrical drainage patterns may also contribute unusual characteristics to build-ups. However, the effect of still another phenomenon—that of movement of fluids within the wellbore—has been neglected in most build-up studies to date. Fluid movements within the wellbore after shut-in occur as a result of after-production, packer failures, leaks in the casing or tubing, or buoyancy of the gas phase when both gas and liquid are present in the well. Each of these movements can influence the pressure build-up, sometimes sufficiently to negate use of the data for computing permeability or stabilized build-up pressure. Examples of each of these phenomena are discussed below. FIELD OBSERVATIONS ON HUMP BUILD-UPS In approximately 75 per cent of the wells in a medium-sized field in South Texas the pressure build-up curves rise to 3 maximum and then decline to what appears to be a stabilized reservoir pressure as shown in Fig. I. Similar behavior has also been observed in wells in other fields in Texas and Louisian:,. Because of the possibility of such behavior being a mechanical failure of the pressure bomb. the bombs were run in tanden into one well which had been known to exhibit this behavior. When both bombs recorded identical curves with the characteristic hump, it was inferred that the unusual build-up is a result of well or forma-

By Peter Richards, Alexander Lewis-Gray, Mark Davies, Nicholas Katsikaros

"Gekko Systems developed the Gekko Resin Exchange Column (G-REX) in order to optimise the recovery of gold in complex leach-to-electrowinning processes, as an intermediate step using a highly gold-selective resin to isolate contaminant metals. The AuRIX®100 resin produced by Purolite is licensed exclusively to Gekko, with the G-REX column designed specifically for this resin (Lewis-Gray et al, 2015). Operational experience has been gained at the CGT Ballarat Gold Plant in near continuous operation since 2008, treating unclarified concentrate leach solution. The extension of the technology to higher throughputs and more complex chemistry is discussed.Aurix®100 ResinAuRIX®100 resin is a cross-linked polystyrene alkaline resin developed by Henkel (Virnig et al, 1996). The resin beads are off-white in colour, spherical, with a nominal size of 100% +600µm. This resin is highly selective for gold and silver over many metals, by way of extracting precious metal cyanide complexes from leach solutions with a pH less than 11.5. The higher end of the pH scale produces best selectivity according to the order of preference: Au > Ag > Hg > Zn > Ni > Cu > Co > Fe. Purolite produces the resin and Gekko Systems maintains licensing of AuRIX®100 resin for use in its G-REX column as part of its unique suite of gravity gold handling equipment.Significant cost savings over carbon-in-solution (CIS) systems are realised with AURIX®100 resin, of around 4% to 12% in capital savings and 27% to 40% in operating costs (Virnig et al, 2004). Allied to this is that AuRIX®100 resin is not susceptible to fouling, that is, the resin does not load with inorganic salts or organic compounds which would affect the loading and extraction of precious metals. To counter any potential for fouling by inorganic salts, in service a dilute acid wash is carried out periodically on the resin to unblock resin pores."

Jan 1, 2016

By S. D. Hill

To help insure the continued viability of the minerals and materials sector of the U.S. economy, the Bureau of Mines is conducting research and disseminating technology that will result in more efficient minerals extraction. As part of this effort, a process is being investigated that involves an aqueous chlorine-oxygen leaching procedure to treat complex sulfide concentrates to produce ZnCl2. Subsequent fused-salt electrolysis of the ZnCI2 produces high-purity zinc metal. Previous reports described preliminary, small-scale research on the chlorine-oxygen leaching system and fused-salt electrolysis of ZnCl2. This report discusses the details of design, construction, and longterm, continuous operation of both monopolar and bipolar fused-salt cells. The effects of temperature, electrode gap, current density, electrolyte composition, and electrode configuration on current efficiency and energy consumption were determined for a ZnCl2-KC1-NaCl electrolyte system. Zinc metal was produced at the rate of about 50 lb/day in a monopolar cell which was operated continuously for 60 days with current efficiencies from 85.8 to 98.6 pct and an average power consumption of 2.1 kwhr/lb. Bipolar cells with several different electrode configurations were operated for 90 days. A current efficiency of about 70 pct and power consumption of about 1.7 kwhr/lb of zinc were achieved using a three-electrode-pair, bipolar assembly with a chlorine gas lift pump to circulate electrolyte.

Jan 1, 1981

By N. A. C. Smith

The Bureau of Mines motor gasoline surveys have been conducted in January and July, during 1920 and 1921. The Bureau has obtained and analyzed samples of gasoline representative of that marketed in the larger cities. These surveys have indicated that the gasoline on the market during the winter months is more volatile than that sold during the summer months. Naturally, the motorist desires a more volatile gasoline in the cold winter months, as it affords greater ease in starting. The fourth semi-annual motor gasoline survey, conducted during the month of July, shows an interesting relation between the market price and the quality of motor gasoline. This is particularly evident if figures obtained today are compared with those of a year ago. At the time the Bureau of Mines conducted its summer survey of motor gasoline last year, the average tank wagon price of gasoline was 28.2 cents per gallon. This year it was 21.2 cents, a drop of practically 25%.

Jan 1, 1921

By Kenneth O. Bayard, John D. Sullivan

"This repot continues the series of papers being prepared at the Southwest Experiment Station of the Bureau of Mines in cooperation with the department of mining and metallurgy, University of Arizona, on factors involved in the leaching of ores. A list of previous publications is given in the bibliography at the end of this paper.Four factors are essential to the leaching of any copper-bearing ore: (1) A solution that will attack the copper minerals must get into the body of the ore particles; (2) the copper minerals must be dissolved by the solution; (3) the solution containing the dissolved copper must find its way out of the voids of the rocks into the main solution; and (4) the copper in solution must be recovered by some means of precipitation.This paper considers the third step -- the extraction of the water-soluble copper. From leached ores. The usual commercial practice in leaching copper ores consists of: (1) Crushing the ore to pass through a screen with approximately one-quarter or one-third inch openings; (2) charging the crushed ore into a fat; (3) adding, usually by upward percolation, a solution that will attack the copper minerals; and (4) washing the copper-laden solutions out of the ore with solutions weaker in copper than the pregnant solution, and finally with water. A countercurrent system of leaching and washing is usually employed. In some plants the solutions are circulated during leaching and washing, and in others they are not. In some plants the wash solutions are added by upward percolation, while at Chuquicamata the so-called ""piston-displacement"" method of washing is employed.The following condensed resume of the leaching cycle of the plant of the Inspiration Consolidated Copper Co. is given to present to the reader a picture of the steps involved in a typical leaching cycle. This plant was recently described in detail.4 The ore, crushed to pass openings 11/2 inches in diameter, passes over a screen with ¼-inch openings. The undersize from the screen goes to a Dorr howl classifier that removes the primary slime from the circuit. The overflow from the classifier is treated in a slime-leaching plant. The oversize of the ¼-inch screen passes through rolls, where it is crushed to pass a 3/8-inchscreen. The undersize from the 3/8-inch screen join with the coarse material from the classifier, and the combined products become the feed to the leaching vats. There are 13 concrete lead-lined leaching vats. The complete leaching cycle is 13 days. Eight tanks are under acid-iron content at all times; three are being washed, one tank is being filled, and the one is being excavated. The electrolyzed solution from the tank house, to which amount of new acid has been added, is put on the oldest tank of ore under need This solution travels from tank to tank and finally emerges from the newest ore"

Apr 1, 1931

By F. Ikumapayi

Hydrogen peroxide production was measured during the grinding of a complex sulfide ore, and its oxidizing effect on solid surfaces was investigated using Fourier transform infrared spectroscopy (FTIR) with diffuse reflectance attachment measurement. In turn, an attempt was made to correlate the formation of hydrogen peroxide, surface oxidation and sphalerite flotation. Additionally, in order to predict and minimize detrimental production problems due to the recycling of process water in sulfide ore processing, the effects of major components of calcium and sulfate species present in recycled process water and the effect of temperature on sphalerite flotation were investigated through bench-scale flotation tests using complex sulfide ores. The significance of process water species in flotation was studied using tap water, process water and simulated water containing calcium and sulfate ions. Formation of hydrogen peroxide was revealed during the grinding of the complex sulfide ore, and its formation was counteracted by diethylenetriamine (DETA). The FTIR spectrum of the pulp solid fraction showed varying degrees of oxidized surface species, which are related to the concentration of H2O2 analyzed in pulp liquid. Bench-scale flotation using two different complex sulfide ores showed that sphalerite recovery is better in process water than in tap water. Flotation results also indicated a varied recovery of sphalerite at different temperatures in either tap water or process water.

By William R. Yernberg

The combined 75th Annual Minnesota Section of SME meeting and 63rd Annual University of Minnesota Mining Symposium was held April 9 and 10, 2002, in Duluth, MN. This year’s theme was “Keys to the Future: Imagination, Innovation and Technology.” The meeting consisted of plenary and technical sessions and a special General Manager’s Session. The technical paper presentations included concurrent mining and mineral processing sessions. In the General Manager’s Session, representatives from the region’s taconite operations presented the current status, concerns and future plans for each of their operations.

Jan 1, 2002

By G. X. Wang, R. E. Siemens, M. C. Fuerstenau, D. Chandra

Soda roasting of concentrates from Mouat, Montana, was performed in a temperature range of 450 to 650 degrees C and chromium was solubilised by water leaching at room temperature. It was found that high extraction yields of chromium were primarily dependent on the conversion of Cr3+ to Cr6+ during the roasting step, and this was enhanced significantly by simple attrition of chromite particles during this step. Gangue impurities (mainly Si) were more detrimental to Cr extraction than lattice impurities such as Al or Mg. It appears that oxidation proceeds into grains along a preferred crystallographic plane in the cubic lattice of the chromite. The effects of roasting time, temperature, soda to chromite ratio and particle size on the extraction of chromium are presented

Jun 18, 1905

By John C. Machisak

THE INJURY data and experience at quarries and related plants of the United States are presented in this publication under the following general sections: (A) General injury experience: Tables 1 through 3: Contain current data on the number of injuries, injury-frequency rates, location, accident agency, degree of injury, and related employment data. (B) Injury experience at different kinds of quarries: Tables 4 and 5: Contain current, data on number of injuries, injury-frequency rates, locution, accident agency, degree of injury, and related employment data. (C) Injury experience by States: Tables 6 through 19: Contain current data on the number of injuries, injury-frequency rates, accident agency, degree of injury, and related employment data.

Jan 1, 1958

By K H. Esbensen, K Engström

The conclusion from the debate over the last decade in the mining sector is that, for grade control, reverse circulation (RC) drill sampling gives more reliable results due to less sampling problems than blasthole samples. However, by conducting the latter with well-controlled procedures there still exist fair possibilities to counteract the major blasthole sampling problems and achieve fit-for-purpose representativeness, especially if based on minimal loss of fines. In the present PhD study, extensive replicate experiments and variographic characterisations are conducted to evaluate the performance of manual blasthole (BH) sampling and sectorial segment sampling. The experiments were performed in Luossavaara-Kiirunavaara AB (LKAB)’s Leveäniemi open pit mine in the north of Sweden. The experimental area is an apatite-magnetite iron ore deposit of the Kiruna type, with the demand to exhibit a maximum of local heterogeneity to allow the experiment the largest possible conclusion powers. Gathering and splitting the complete BH drill cutting cones (fines cone, coarse cone) served as an authoritative reference on which to assess the representativity of the two BH sampling methods.Results show that manual BH drill sampling is able to produce samples with an acceptable accuracy and precision if performed properly and with insight. Based on variographic comparison, segment sampling shows similar precision for chemical grades as the manual sampling, while the particle size distributions were more deviating for segment sampling than for manual sampling at the high and low size ranges. Possible reasons for these partly surprising results are discussed.For further investigation of the performance of BH versus RC drill sampling, a second experiment has been planned on a parallel profile. This will result in an unprecedented opportunity for a full variographic comparison between RC and BH sampling, aimed at designing specific, fit-for-purpose sampling procedures as a function of ore quality, cut-off grades and important contaminant levels.CITATION:Engström, K and Esbensen, K H, 2017. Blasthole sampling (replicate and variographic experiments) in LKAB open pit iron ore mines – fit-for-purpose representativity?, Australia, in Proceedings Eighth World Conference on Sampling and Blending , pp 85–96 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017