Search Documents

By Dan Brown

This paper presents a case study of a cyclic lateral pile load testing program performed on two 18-in square prestressed concrete piles (PSC) in Savannah, Georgia. The load test program was developed to simulate the lateral behavior of a single pile under seismic loading conditions for the design and construction of a large LNG storage tank. The lateral load tests included cyclic loading to measure possible degradation in soil response followed by static loading to large displacements (around 6 inches at the loading point). The lateral load was applied through a reciprocating jack positioned to push and pull the piles against each other. The test piles were instrumented with multiple displacement transducers, downhole inclinometer, and strain gauges. This paper provides an interpretation of the test results regarding the pile performance and soil response to monotonic and cyclic lateral loading. A backfitted computational model of the soil resistance was developed to match the test results using the LPILE computer program. The load-deflection and deflection/moment versus depth comparisons suggest that this model appears to capture the behavior relatively well within the general range of suitability for design purposes. New design curves were developed based on the soil parameters derived from the lateral load test results.

Jan 1, 2003

By Robert B. Johnson

The refraction seismic method has been used as an indirect means of exploring for fluorspar in southern Illinois by the Illinois State Geological Survey. Use of the method has been restricted to those areas where mineralization is associated with faults, a restriction necessitated by the operating principles of the refraction method. The seismic data enable the interpreter to locate fault zones in the subsurface and, under ideal circumstances, to make estimates of dip direction and magnitude and vertical displacement provided the local stratigraphic units are known and are geophysically recognizable. In this instance, refraction seismic exploration has been successful in the surface mapping of well-developed faults, both simple and complex with which fluorspar may or may not be associated. However, less clear results have been obtained where faulting has been less severe and where there are numerous accompanying mineralized joints.

Jan 1, 1964

By William R. Yernberg

SME’s Arizona Conference was held at the Doubletree Hotel at Reid Park in Tucson on Dec. 5and 6, 2004. The annual conference is organized by the Arizona Conference Board of Directors, which represents SME sections in Arizona and adjacent areas. The conference provides an opportunity for individuals and corporations associated with mining in the region to get together each year to discuss the status of the industry. The meeting featured a keynote address and more than30 technical papers. Two years ago, the U.S. copper industry was facing on a run for two years now,” and “both precious metal and base metal prices are going up.” The increases in metal prices were attributed to development in China and other Asian countries. “With a population of 1.6 billion, China has recently created 80 million jobs,” said Silver.

Jan 1, 2005

By Huw Williams

It is becoming increasingly common practice to re-use existing foundations for new projects, especially on urban sites where geotechnical conditions are congested. A knowledge of the foundation dimensions and capacity is essential for this to take place, however, as-built records are often non-existent. Non-Destructive evaluation (NDE) is now becoming an important tool in assessing old foundation properties and their potential for re-use. Pile dimensions are also critical in the power industry, when they are supporting transmission towers which need to be upgraded, and may carry additional wind loading. This paper describes the application of various NDE techniques that are available and how they can be used to determine pile length, shape and capacity in difficult site conditions, including foundations under structures.

Jan 1, 2006

By Richard Peaker, Jens Lichter, Alexander V. Potapov

The recent combination of Computational Fluid Dynamics (CFD) and Discrete Element Modeling (DEM) can provide considerable insight into the performance of flotation cells. One area of interest from a fundamental equipment design perspective has been the influence of flotation cell size and the inflow rate on the metallurgical performance of the cell. One of the specific design objectives when increasing the size of flotation cells, or increasing the feed flow to the flotation cell, is to ensure that the feed stream flowing into the cell does not have an opportunity to bypass the mechanism. This paper describes the initial modeling efforts to quantify the inter-relationship of cell size, inflow rates, and feed and discharge box placement, on the retention time distribution of solids in the flotation cell, and the fraction of particles that bypass the mechanism on a size by size basis.

Jan 1, 2007

By N. A. D. Parlee, M. T. Utine

ThE kinetics of absorption of oxygen by induction-stirred liquid silver (at constant Po2 and T) has received some study here.''2 This paper describes a study of the kinetics of effusion (non-bubble-forming), and some additional work on absorption. A Sieverts type of apparatus was used. The kind of reaction tube assembly has been described.4 The same 25-kw, 450-kc induction unit was used as in earlier absorption work1'2 but the "coupling" was different. The runs were made under the following conditions: i) saturation at 1 atm, effusion at 0.81 atm;

Jan 1, 1969

By Paul Eger

The use of wetlands to treat mine drainage has become increasingly common, particularly as more information is available on their operation and construction. However, the lifetime of each system is still, at best, an estimate. Treatment lifetime depends on the types of processes that provide the majority of the metal removal. Anaerobic systems (vertical flow systems) rely primarily on sulfate reducing bacteria, which reduce sulfate to sulfide and generate alkalinity. Metals can be precipitated as sulfides, and acidity is neutralized. These systems can remove over 90% of the metals and increase pH from around 4 to over 7. The bacteria will remain active as long as the system remains anaerobic and contains an adequate supply of sulfate and small chain organics. Although estimates of lifetime made on the total carbon in the system suggest that lifetime should exceed 20 years, data from field and laboratory studies show that the rate of sulfate reaction decreases with time, and that after several years rates decreased substantially. To maintain acceptable treatment, either additional organic material must be added or the total metal and acid load to the system would need to be reduced substantially. Aerobic systems (overland flow wetlands) can effectively remove metals from neutral mine drainage by reactions with organic material in the substrate. Over 90% of the copper and nickel have been removed in aerobic systems treating mine drainage in Minnesota. The primary removal processes in these systems include adsorption, ion exchange and complexation, which are finite; removal will cease unless new removal sites are generated. Two wetlands built in Minnesota have been successfully treating mine drainage for 12 years. At one of the wetlands, the annual production of new removal sites has been estimated to be equal to the annual metal input, and, as a result, metal removal should theoretically continue indefinitely.

Jan 1, 2005

By David Hake, David Salisbury

The Drainage Services Department (DSD) of the Hong Kong SAR Government commissioned the design and construction of the West Kowloon Drainage Improvement, Stage 2, Phase 2, Kai Tak Transfer Scheme (KTTS) project in 2000 to relieve potential flooding in Mong Kok caused by the insufficient capacity of the existing storm water drainage system. The KTTS involves construction of a 1.5km,4.4m drainage tunnel and a 450m long box culvert, running from Waterloo Road near Hereford Road to the existing Kai Tak Nullah in San Po Kong. This paper describes the design and construction of; the bored tunnel through both hard rock and soft ground using a slurry Tunnel Boring Machine (TBM), six associated access shafts, a connection structure at Waterloo Road and the box culvert connecting the bored tunnel to the outfall at Kai Tak nullah. Details will be provided on the contractor’s alternative designs adopted during the contract including the use of fibre reinforced shotcrete as one-pass temporary and permanent support for three of the shafts and modifications to the Engineer’s design for the box culvert structure.

Jan 1, 2005

By Henry Stoch

It?s a green, green world ? Public concern about the impact of human activities on the environment and the roles that businesses play in that impact is rising. What?s happened in the last few months? ? Recent news: ? British Columbia announces carbon tax in 2008 budget ? Federal Court ruling stalls oil sands approvals due to a lack of consideration of GHG implications ? US Energy Independence and Security Act could limit government procurement of oil sands-derived fuels ? Western Climate Initiative (WCI) suggests a ?first seller? approach for regulating generators outside WCI jurisdictions ? Implications ? A cost for carbon has arrived ? The lack of a GHG strategy can have a material impact on your business ? Regulations in other jurisdictions could affect your organization

May 1, 2008

By Linli Wu

During the measurement of contact angle, a misty band was observed near the substrate. Hsien-Nan Ho and Shinn-Tyan Wu thought this was because the oxygen atoms on the interface migrate to the droplet surface to form an oxide band near the substrate. But from our experiments misty band appeared before the drop reach to the substrate. Theoretically speaking, the oxygen partial was the same everywhere in the vacuum furnace. So there was no condition to provide enough oxygen forming oxide. This appearance would be explained more reasonably with the optics principle. Most reflected light would be absorbed by the substrate and the light cannot reach the observation area, so the misty band formed.

Jan 1, 2006

By L. E. Fish, G. S. Wyman

CHUQUICAMATA open-pit mine is capable of producing a total of 105,000 tons daily. When the sulphide plant is operating to capacity the distribution of this quantity will be approximately 30,000 tons sulphide ore, 30,000 tons oxide ore and 45,000 tons of waste. At that time the combined capacity of the oxide and sulphide plants will be about 540 million lb of copper per year. Twenty one benches have been opened to date and all are still active except the three top ones at the northeastern limit of the pit. These have been pushed back to final slope line. The pit is 8850 ft long, 3540 ft wide and 980 ft deep. Benches are not all developed to a standard height as the large development shovels used in cutting new benches have been of different size and range. At this time new benches 521 ft high are being developed with an' 11-yd shovel. Ore haulage through the greater part of the pit operation has been on down grades to the crushing plant. With the opening of bench F-4 in April 1944 the first adverse-grade ore haul was encountered. Of the total tonnage now being mined, 35 pct comes from the four benches that are below the level of the crushing plant yard. Waste had been dumped on the same or nearly the same level as the bench from which it was removed up to the opening of bench F-4. Waste from this and lower levels is hauled to the level of the crusher, yard where it must cross the flow of ore traffic to reach the only available dumping space to the east of the mine. The average ore haul is 3.13 miles one way shovel to crusher, and the average waste haul from that portion handled by railroad is 3.32 miles one way from shovel to waste dump. Waste that is being removed by truck haulage from the upper part of the -mine is hauled an average of 1 mile. Ore loaded by trucks is hauled 3/4 mile to a car loading ramp and then by rail to the crushing plant. Drilling and Blasting There are two types of development for blasting being used: One for opening new benches and the other for bank shooting. The former consists of 9a in. diam churn-drill holes drilled 11.8 ft center to center in rows 10.2 ft apart with the holes staggered in the rows thus giving an equilateral-triangle pattern of 11.8 ft on a side. After the first block, 492 ft long by 71.5 ft wide, is shot in the pattern described above, the cut is advanced by smaller shots consisting of four rows of holes spaced 23 ft center to center with the rows 23 ft apart. These shots are fired in conjunction with side shots in which the holes are drilled 33 ft center to center and 29.5 ft back from the toe, thus squaring up the bank for subsequent shooting. An average bank shot consists of about 60 holes drilled in two rows parallel to the face, 30 holes to

Jan 1, 1952

By William R. Yernberg

A conference on coalbed and coal mine methane was held March 27 and 28, 2000, in Denver, CO. The conference, organized by the Strategic Resource Institute, was attended by leaders in the coal mining and gas energy industry. The conference focused on the recovery of methane from coal beds as an energy resource and the removal and utilization of coal-mine methane (CMM) related to underground coal mining. The two-day conference discussed methane resources around the world, methods of recovery, methane markets, underground coal mining, health and safety issues and environmental issues related to methane. The consensus among the presenters is that the future looks promising for coal bed methane (CBM) and CMM.

Jan 1, 2000

By David S. Bowling

The ER-300 Series White Recorders were developed to provide on economical, yet invaluable instrument for those who desire permanent recordings of such data OS displacement, vibration, concussion (air borne effect) and velocity information. The precise monitoring of earth displacements and air blast magnitudes aids quarrymen and construction contractors in estimating safe blasting limits when operating in populated areas. A refraction model is available for recording velocities which permit the determination of weathered zone depths as well as the .depths to other subsurface formations. The dual purpose (Refroction- Displacement) systems ore utilized for velocity studies and displacement - oir blast measurements.

Jan 1, 1990

By Halagowder Devaraj, Mostafa Sheykhnazari, Veer P. Bhavanandan

"A sensitive colorimetric assay for detecting mucins and glycoproteins rich in 0-glycosidically linked saccharides is reported. The method combines the susceptibility of N-acetylgalactosamine terminating 0-glyco idically linked saccharides to P-elimination with the Morgan-Elson reaction for N-acetylhexosamines with free reducing ends. All mucin and mucin-type glycoproteins but none of the serum-type glycoproteins tested resulted in characteristic color production. All mucins tested gave linear responses in the range 5 to 200 ""g and the assay was also adapted to the microscale involving the use of 96-well microtiter plates. The microassay in which the volumes of samples and reagents are scaled down 2.5-fold was particularly useful in monitoring of mucins, in the presence of other glycoconjugates, in large numbers of samples obtained during fractionation procedures. Cesium chloride, cesium bromide, potassium thiocyanate, and various detergents do not interfere with the colorimetric determination. Guanidine hydrochloride, cesium triftuoroacetate, and B-mercap- . toethanol decreased color by 30 to 45%; however, the interference was not serious to prevent the use of the method for detection of mucins in their presence. The use of the method for the specific detection of mucin during fractionation by gel filtration and density gradient centrifugation of cystic fibrosis sputum samples is demonstrated. Mucins are an important class of biomacromolecules whose structure-function relationship is poorly understood (1,2). The investigations of mucins are hampered by difficulties in purifying these very large size molecules which appear to avidly bind other components of the mucus (3,4). One of the problems during purification is the specific detection of mucins. For example, during the various purification steps, the fractions containing mucins are typically detected by assaying for neutral sugars (hexoses) (5,6), for sialic acids (7), or for periodate oxidizable saccharide units (8). However, these methods are not entirely satisfactory because neutral sugars, sialic acids, and periodate-oxidizable saccharides are also components of other glycoconjugates. In addition, the neutral sugar and sialic acid measurements are also subject to interference from high levels of proteins and nucleic acids."

Jan 1, 1990

By Andrea McGlynn

Iron Ore Company of Canada, Labrador City 2011?Canada's largest iron ore producer, leading global supplier of iron ore pellets and concentrates ?Rio Tinto (58.7%), Mitsubishi Corporation (26.2%), Labrador Iron Ore Royalty Income Fund (15.1%)

May 1, 2011

By Anthony Hammond

Geographic Information Systems (GIS) are powerful analytical and data display tools for mining industry management, capable of linking spatial features with tabular data and integrating communications across departmental boundaries. In this sense, the paper point out the GIS application concentrates in four technical areas of underground mining: ownership and mineral claims; exploration management; production; and mine safety. GIS provides land and exploration managers with the ability to consolidate and archive claim data and to georeference property maps defined in local coordinates into world coordinate systems. GIS’s proximity analysis identifies areas of potential safety concern and points to and maps the shortest routes to emergency exits, facilitating the prompt evacuation of mine personnel.

Aug 25, 2002

By T. Groenewald

Potential applications of thiourea In the processing of gold by T. GROENEWALD, Ph.D. (Rand), D.I.C. (Imperial College) (Visitor) The aqueous chemistry of gold(l) that has found practical application is mainly the chemistry of the anionic complexes involving ligands such as cyanide. sulphite, and the halides. The one potential exception is the cationic gold(I)-thiourea ion. While many laboratory studies have been made during the past decade. the application of thiourea in the processing of gold is only now reaching the development stage. While thiourea is relatively inexpensive. recent interest has probably been spurred mainly by the novel technology that could arise out of the cationic properties of the gold-thiourea ion. This review outlines the chemistry of gold and thiourea. and discusses the possible use of thiourea in the processing of gold with respect to dissolution. solvent extraction. ion exchange, electrowinning. electroplating. electroless deposition. electro-etching, and electropolishing.

Jan 6, 1977

By M. Mabuza

Two Rivers Platinum Mine (TRP) is a 55:45 joint venture between African Rainbow Minerals and Impala Platinum, respectively. TRP is situated on the farm Dwarsrivier 372KT, in the southern sector of the eastern limb of the Bushveld Complex. Dwarsrivier is underlain by rock formations of the Critical Zone (Winterveld norite-anorthosite) and the Main Zone (Winnarshoek norite- anorthosite). Two economically significant PGE-bearing layers namely the Merensky Reef and the UG2 chromitite are found within the upper Critical Zone. These are approximately 140 m vertically apart, separated by a series of barren norites and anorthosites. At Two Rivers Platinum, only the UG2 chromitite layer is currently being mined for PGEs. The UG2 sub-outcrops north/south along the Klein Dwarsrivier river valley with a very gentle dip to the west of 7º?10º. At Two Rivers the UG2 averages about 120 cm in thickness, overlain by a waste pyroxenite parting about 20 cm thick, above which is a leader seam about 20 cm in thickness. The mineable cut consists of the leader seam, the waste pyroxenite parting, the UG2 chromitite layer including 25 cm of pegmatoidal pyroxenite footwall, below the UG2 reef to a minimum of 185 cm trackless mining cut. The mining method is a mechanized bord and pillar layout, which will yield a total of 185 000 tons at full run of mine production from the underground UG2 mine.

Jan 1, 2007

By X. Cao, R. Wang, H. Han, Y. Hu, Z. Wei, W. Sun, H. Tang, J. Wang

Flotation reagents play a vital role in mineral flotation. In the past century, most studies focused on the modification of anion or cation collectors and the synergistic effect of mixed collectors, which have contributed to research. In this study, we reviewed brand-new reagents, metal-organic/inorganic complexes, with the functional group of metal ion, which are totally different from the traditional anion or cation collector and show absolute specificity for some minerals. For example, Pb-BHA complex collector was developed to realise the atmospheric flotation of scheelite due to the absolute specificity for calcium minerals. Calcium oleate collector was found to be the effective species in the flotation of calcium minerals, and has been employed to selectively separate fluorite from calcite. Selective adsorption of Al-Na2SiO3 polymer on calcite surfaces proved the self-assembly of H2SiO3 polymer using Al3+ had stronger selectively adsorption ability than Na2SiO3. Also that Fe3+-starch complex was a better depressant for iron minerals than caustic starch and contributed to a more efficient reverse flotation. In conclusion, metal ions are good templates for molecular assembly and can be used to control the structure of metal complexes and exhibit special properties, which provide possibilities for the design of new flotation agents. Keywords: Metal-organic/inorganic; flotation; collector; depressant

Jan 1, 2020

By G. S. Scott

In the course of the investigation into the causes, behavior, and control of mine fires, which the Bureau of Mines is now conducting, some attention was given to the subject of spontaneous heating. It is self-evident that the temperature of a pile of broken coal will rice if the rate of generation of heat exceeds the rate of brat dissipation and will fall if the opposite is the case. Factors that affect the rate of generation of heat are:

Jan 1, 1941