Search Documents

By Michael R. Norland

Surface and subsurface stabilization of mining-related wastes through revegetation depends upon the physical, chemical, and biological condition of the waste following mining. Mining disturbances can significantly alter the soil physical, chemical, and biological characteristics of a site, reducing or eliminating mycorrhizal fungi from the soil. Mycorrhizae are economically and ecologically important because they can alleviate environmental stresses caused by lack of proper soil condition and because they are vital to stabilization of mining waste by increasing plant survival and biomass through increased nutrient and water uptake. This report discusses some of the ecological factors that may affect mycorrhizae-plant associations on mining-related wastes and provides general information on mycorrhizae inoculation technology.

Jan 1, 1993

By Sir John Cadnan

The production from the Maidan-i-Naftun area for the year ending March, 1928, was 5,340,000 tons (40,210,200 bbl.), an increase of nearly 13 per cent. over the production for the year ending in March, 1927. The production by years since the opening of the field in 1912 is given in the following table: [1 ton = 7.53 bbl.] Year Ended MaRch Tons Year Ended March Tons 1912 (7 months)............. 43,084 1920....................... 1,354,631 1913........................ 80,800 1921....................... 1,767,070 1914........................ 273,635 1922....................... 2,310,098 1915........................ 375,977 1923....................... 2,913,908 1916........................ 449,394 1924....................... 3,583,000 1917........................ 644,074 1925....................... 4,221,000 1918........................ 897,402 1926....................... 4,470,000 1919....................... 1,081,919 1927....................... 4,735,000 1928....................... 5,340,000 The actual production represents only a small proportion of the potential production. The Masjid-i-Suleiman Field The present producing unit, the Masjid-I-Suleiman, is an anticline some 20 miles in length by 4 miles in width, including three domes as so far proved. The producing horizon is a very open, dolomitic limestone, which, while showing much variation in texture and porosity, is so connected that the lowering of pressure in one section of the field quickly affects the whole area. The topography of the field is broken, with differences of well elevations of as much as 1100 ft. The depths to the limestone vary from about 800 to about 5000 ft. The closed-in pressure of the oil wells varies from zero to 50 lb. per sq. in. and that of the gas wells is about 450 Ib. Although the static oil level may be several hundred feet below ground level, in oil wells of high elevation, all the wells flow continuously or intermittently after they are once started—the majority continuously. The gas is very high in hydrogen sulfide in gas-oil wells of low pressure.

Jan 1, 1929

By A. B. Hooker, L. C. IlsLey

Several ignitions or mine pa, which might have led to explosions, and at least ona mine fire attributed to heated leg wires of electric detonators, have occm.rred. at rn1::.es in which outside shot firing is practiced. Photographs taken at one mine ind.la.ted. that the wires became red hot during firing. These results having been --i·-led. to the .Lttention of the electrical section of the Bureau of the Mines, ignitions the tests and to reportd aid in herein preventing were made future to trouble determine of if this possible kind, the cause of The investigation, which 1• considered preliminary, included tests to determine the conditions tha.t cause gas ignitions from heated. leg wires of electric and. of detonators, copper leg possible wires, remedies The tor samples such of heating, wire used. and in the the relative test were behavior the of reg\llar ironDa. Pont iron and copper leg wires (No, 22 A,W,G.) C\1t from Du. Pont electric detonators.

Aug 1, 1922

General recognition of the potential benefits of utilizing advanced technology has focussed public attention on the organisation of tertiary education. This has produced a situation where opportunities exist for significant changes to be implemented. The challenges to Mining education in this environment of change are analysed with respect to the setting of education objectives, the role of centres of education, course structures and student access to courses. The scope of the analysis includes formal courses for professional education and technical training, and programmes for continuing education and postgraduate research. Previous significant advances in mining technology illustrate the importance of encouraging the establishment of an extensive involvement with mining education. Education cannot be the sole responsibility of professional academic organizations; significant industry participation is essential. Methods of achieving this interaction are discussed. Major changes in techniques available for disseminating information provide a significant incentive to assess the relevance of existing course structures and restrictions on student access to courses. Establishment of a less rigidly progressive system of education is discussed with respect to the development of the full potential of computer based learning. This will expand the availability of mining education to include remote locations. The practical feasibility of such changes and recognition of the value of education as a commercial resource could also increase overseas involvement in Australian mining education. Benefits of such changes and problems that may develop if accreditation systems are not also changed to take account of new technology are outlined.

Jan 1, 1989

By Y. R. Murthy, S. Angadi, A. K. Bhatnagar, S. K. Tripathy, L. O. Filippov

Dolomite is an essential raw material for the refractory industry, a flux in the iron and steel industry and also for the extraction of magnesium metal. Generally, particle size reduction, screening and classification are used for the preparation of the high-grade sized material for different applications, whereas low-grade fine fractions are not utilised. These fines or low-grade overburdens are dumped at the mine site for future utilisation, which creates environmental issues along with inadequate space management. In the present investigation, a detailed study was carried out to decrease the silica content of the low-grade dolomite fines from Gomardih , India, containing 28.6% CaO and 20.1% MgO along with 8.3% silica. Different process flow sheet options were evaluated with a combination of dry classifier, wet classifier, gravity concentrators as well as flotation. Different process variables were assessed along with mineralogical characterisation to optimise the process for efficient rejection of siliceous gangue minerals. Results indicated that dolomite, calcite and quartz are the major mineral phases present in the ore along with other minor minerals. It was concluded that two-stage flotation was an effective process for the reduction of silica up to below 1% after grinding to a particle size below 212 μm. A process flow sheet with a combination of gravitation air classifier and flotation can produce a concentrate with silica content below 4.5%. Keywords: Dolomite, flux, dry classification, flotation, characterisation, beneficiation

Jan 1, 2020

The demands of the economy require larger manufacturing facilities using greater quantit- ies of raw materials which must be mined, handl- ed, stockpiled and recovered with efficiency and dependability. All over the world, mining com- panies, steel manufacturers, power stations and process plants are not only seeking but finding methods of increasing outputs and'reducing costs in the field of materials handling. In mining bigger continuous mining machines and shovels, larger trucks and crushers are digging and processing greater quantities of differing materials which have to be handled and shipped at rates once thought to be impossible. To implement such schemes demands the blending of a lot of diverse-equipment, mining machinery, bins, feeders, reclaimers and it is here that the belt conveyor assumes a role of ever increas- ing importance. Significant developments have taken place in the seventies with respect to conveyor belt transportation; not only in the systems but also in the components which combine to make such systems work efficiently.

Jan 1, 1976

By M. H. Moys, J. A. Finch, A. R. Laplante

"A detailed review of ball milling circuit control practices in industry has been carried out. Based on fundamental process performance objectives, a standard system for base-level control of most ball mill installations is presented. This system is simple, inexpensive, and provides the major economic benefits available from contemporary automatic control technology.Value Analysis of Grinding OperationsValue analysis (or engineering, or management), originally developed by Lawrence D. Miles of the General Electric Company (1), focuses on the identification of value (product or process worth versus cost) and provides a systematic procedure for its improvement. A recent research and development project involving the application of the principles of value engineering to grinding operations has provided a basic technoeconomic model of grinding processes (2). The functional objectives of the ball milling process and the means to achieve value based grinding circuit control originate from this study.The Need for Grinding Circuit ControlThe economic effectiveness of a process is determined by the quality or value of the product and the related processing costs. If the inputs (both the raw feed and the applied processing work) are absolutely constant, the product characteristics and the process efficiency will be determined only by the engineering design. The need for and degree of process control is therefore determined by the nature of variations or upsets in the process inputs, and the extent to which these effect product value and operating costs."

Jan 1, 1988

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specificetiona that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the fusing temperature of ash and the free-swelling index. Under most of these specification contracts the bidders guarantee the quality of the coal, end that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions3/ issued by the Bureau; the samples are analyzed in the Bureau's laboratory to determine whether the coal is of the quality guaranteed by the contractor and, if it is not, a price adjustment is made. Analyses of the delivered coal and "tipple" samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered 1s a check on the practical results obtained in burning the coal.

Jan 1, 1953

By Robert F. Randolph

Introduction This paper is a descriptive analysis of injuries and fatalities at small surface bituminous coalmining companies in Pennsylvania. The purpose of analyzing a specific industry sector and location is to identify issues that might be missed in a wider analysis. Other studies of small mine safety (e.g., Peters and Fotta, 1994, Randolph and Boldt, 1997) have shown that the relationship between safety and mine size is not a simple one. Some injury types occur at higher rates at small mines, while others occur at lower rates. Consequently, an analysis limited to a specific type of mining can help identify hazards and issues specific to that sector. The results of this analysis will be useful for directing training, intervention, and research efforts towards the most prevalent causal factors and incident types. Procedures and Definitions Data sources The primary sources of data for this analysis were files provided by MSHA containing information collected under Title 30 Code of Federal Regulations, Part 50. These files, commonly referred to as “Part 50 data”, are provided though MSHA’s Program Evaluation and Information Resources directorate. Two primary types of injuries were selected from the Part 50data: Fatalities (MSHA “degree of injury” code 1) and lost-time injuries, otherwise known as nonfatal with days lost (MSHA “degree of injury” codes 2 through 5). Lost-time injuries involve either actual days away from work or days of restricted activity or both. Fatality and lost-time injury incidence rates were calculated using the standard MSHA formula: Number of injuries per 200,000 employee-hours. Additional information on company sizes and mine ownership was provided by the Pennsylvania State University College of Earth and Mineral Sciences. Time span A five-year time span was selected for this study. More than a single year of safety experience is usually needed to capture a broad range of incident types. Many types of injuries, especially fatal injuries, can be extremely rare, and may be missed if too short a time span is selected. However, a time span that extends too far back may begin to suffer historical threats to validity. That is, incidents that occurred several years ago may be caused by hazards that have since been remedied or may be related to mining practices and conditions that no longer exist. A five-year span offers a practical compromise between these two concerns. Consequently, the MSHA Part 50 data files from 1993 through 1997 were used. The 1997 file was in “preliminary” form at the time of the study, so small variations from the final 1997 “close out” file can be expected. Based on past experience, we do not expect the close-out variations to have a significant impact on the findings.

By Thomas Kuhn, Carsten Ruehlemann, Christina Heller, Anna Wegorzewski

The commercial extraction of metals from manganese nodules on an industrial scale requires more than 50% of the investment necessary to realize manganese nodule mining. This is mainly due to the fact that a completely new metallurgical processing scheme for the extraction of both base metals (Ni, Cu, Co) and high-tech metals (Mo, Li, Ga) has to be developed and upgraded to industrial scale. There are a number of conventional processing technologies that combine hydro- and pyro-metallurgical approaches such as the INCO and CUPRION processes which have been developed in the 1970s and 1980s. Today, new approaches based on selective leaching with chelating agents and bioleaching try to minimize energy consumption and waste production. All of these extraction methods require knowledge how the metals are structurally bound in the manganese oxides. In this contribution we will review the current knowledge about the mineralogy of iron and manganese minerals in the different marine oxide deposits, present our results, and discuss the possible consequences for metal extraction.

Sep 1, 2014

By Lyman G. J

Dense medium drum separator efficiency was analysed at two Western Australian iron ore concentrators. Efficiency data had hitherto been difficult to accumulate due to the high cost of analysing representative, and therefore large, coarse ore samples. To overcome this problem, recoverable density tracers, which are in effect artificial mineral and gangue, were manufactured in three different sizes (15 mm, 30 mm and 60 mm). Their use enabled partition curves to be studied within one hour of conducting a test: separation densities were generally lower than the feed medium density for all three sizes of density tracer. For a given set of operating conditions, the smaller tracers had lower separation densities and larger ecart probab/es than the large tracers. These phenomena are explained with the aid of a conceptual model of a drum separator, which assumes that the feed ore plunges to the bottom of the drum upon introduction. Particle rising velocities are, therefore, process determining.Medium rheology was altered by adjusting the proportion of solids in the pulp. This was accomplished by changing both the pulp density and ferrosilicon/magnetite ratio. Higher solids volume fractions invariably caused a decrease in separation densities and an increase in ecart probables, most markedly for the smaller tracers. A similar response was observed when feed tonnages were raised.An explanation for these phenomena is sought in the discussion which also suggests means of improving drum separator efficiency.

Jan 1, 1987

The 20th annual American Mining Hall of Fame Awards Banquet sponsored by the Mining Foundation of the Southwest will be held at the Westin La Paloma in Tucson, AZ, on Saturday, Dec. 7, 2002. This year’s inductee, guest of honor and featured speaker is J. David Lowell, one of the preeminent exploration geologists of the past 30 years. Among his most recent discoveries is the world-class Pierina gold deposit in Peru, currently owned and operated by Barrick Gold. As representatives of mining heritage, the Hall of Fame will induct Howard Allen Twitty, Sr., and Bernhardt Rohe. Twitty was a respected public lands attorney. He made significant contributions to the mining industry by representing several major companies in many court cases. He was also the author of numerous papers on mining law. Rohe was managing director of Peñoles. In that position, he helped guide the Mexican mining company for its growth into the international mining company that it is today.

Jan 1, 2002

By M. McWha

Laboratory bias is a universal problem in all branches of analytical science. It results from differences in methods, techniques, equipment, and calibrations between laboratories. Notwithstanding that it is a property that can be measured by the use of standards or by inter-laboratory testing, laboratory bias remains a material issue for the mining industry. There is extensive literature and clear guidelines on measurement from the International Organization for Standardization (ISO) and its worldwide federation of national standards bodies (ISO member bodies) and from the science of metrology. ISO guides cover the manufacture and use of standards. An accessible source of literature covering laboratory quality control comes from the public health sector, particularly pathology. There is little doubt in financial reporting rules about the meaning of materiality. Public reporting guidelines are clear that material matters need to be disclosed for investors. Unfortunately there is currently no clear guidance what to do about biased assay results in mineral industry public reporting guidelines. This paper reviews the requirements for the manufacture and use of reference materials, public reporting requirements in the mining industry, and presents proposals to improve management and reporting of laboratory biases. Keywords laboratory bias, reference materials, ISO Guides, financial reporting, materiality.

Jan 1, 2014

By John L. White

Vibratory driver/extractors do more than drive and extract sheet piles. I would say more than sixty percent (60%) of the time, vibratory pile driver/extractors are engaged in work that has nothing to do with sheet piles. This is the main reason I refer to this tool as a "driver/extractor", and omit the word "pile". I have spent the last twenty years applying the technology of the vibratory driver/ extractor to all areas of foundation construction. As you will see, the only limits are humankind's ingenuity.

Jan 1, 1997

Retreating Cu-Mo Rougher Tailing by Flotation for Concentration of Copper and Molybdenum

Sep 13, 2010

By Bruno Bussière, Guosheng Zhan, Michel Aubertin, Vincent Martin, Robert P. Chapuis

The study evaluates the hydrological behaviour of exposed and covered waste rock dumps. The objectives were to determine the major factors influencing unsaturated flow in waste rock dumps and covers, and to improve the in-situ, laboratory and numerical modeling characterization methods. Using material properties obtained from in-situ and laboratory tests, waste rock dumps of different configurations, with and without covers, were modeled. It was found that a properly designed “Store, divert and release” (SDR) cover allows most of the water to be diverted downslope and discharged outside of the waste rock dumps. The SDR cover seems to work efficiently even in extreme storm events. The numerical modeling results show that the unsaturated hydraulic properties (e.g. air entry value and water entry value) of the materials largely control the infiltration of water into waste rock dumps.

Jan 1, 2005

By A. Butler

This paper explains the politics of mine nationalization in contemporary South Africa. Nationalization and privatization typically occur in the oil, mineral resources, and state utilities sectors, and they tend to follow one another in a long-term cyclical pattern. The paper explains why the current international environment has encouraged demands for nationalization and other forms of ?resource nationalism? in the South African minerals sector. It goes on to describe how the resurgence of resource nationalism has been influenced by internal factional politics in the African National Congress. It concludes that nationalization is unlikely to be the outcome of current policy deliberations within the ANC.

Jan 1, 2013

By Hongqiang Wang, Qingliang Wang, Eming Hu, Zhiwu Lei, Fang Hu, Rui Zhang, Wei Hou

Pyrite, a mineral associated with uranium ore, is closely related to uranium leaching. In this study, Ozone micro-nano bubbles (OMNBs), as an environmentally friendly advanced oxidation technology, were used for the first time to oxidize pyrite under experimental conditions to improve the leaching rate of uranium. A laboratory-scale agitation leaching experiment of pyrite was carried out with a pH of 1.0–3.0, gas flow of 1–3 L/min, ozone generation rate of 0.55–2.22 mg/s, and pyrite concentration of 0.1–5.0 g/L for 1 h. By adding three different co-oxidant: Mn(II), Mn(IV), and Fe(III), it was found that only Mn(IV) increased the oxidation rate of pyrite by 21.7%. The results of the scanning electron microscope (SEM) and X-ray photoelectron spectroscopy (XPS) show that the formation of Fe(III)-O film on the surface of the ore suppresses the oxidation rate of pyrite to a certain extent. Pyrite can be rapidly oxidized up to 57.6% by OMNBs, which is beneficial to uranium leaching. This method is expected to be used for in situ acid leaching of uranium with OMNBs injected into the ground.

Jan 3, 2022

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

3.1 INTRODUCTION The final subsidence basin discussed so far is that developed long after mining has stopped. In a supercritical final subsidence basin, the central portion subsides uniformly. Thus any structures located there are not subjected to any final permanent surface deformation. But this statement is only true for the final subsidence basin. When the face is moving, the structures are subjected to dynamic deformations associated with the dynamic subsidence basin. For instance the house in front of a moving face (location 1 in Fig. 3.1) is subjected to the maximum tensile strain and the maximum positive curvahue. When it falls behind the face in location 2, it is subjected to the maximum compressive strain and the maximum negative curvature. When the house is far behind the face in location 3, it returns to its original condition with only uniform subsidence. However, the magnitude of the dynamic deformations may be sufficiently large to damage a structure in locations 1 and 2 before it reaches location 3. Therefore it is very important to study the characteristics of the dynamic subsidence basin. Under normal conditions, when the face has advanced for a distance approximately one-sixth to one-third of the seam depth from the setup entry, depending on the seam depth and the physical properties of the overburden strata, the movement of the over- burden strata reaches the surface, whereupon the surface also be- gins to deform. Thereafter, the surface point where the movement initiates is always located at a fixed distance ahead of the face. The angle between the vertical line at the faceline and the line connecting the movement initiation point on the surface and the face- line is the angle of advance influence, w. The angle of advance influence can be used to determine the distance, [ 1], which is the influence zone ahead of the face. w is approximately 20O to 35 O for the northern Appalachian coalfield (Peng and Geng, 1984). The movement of each surface point is a relatively complicated process both in time and in space, because the relative position between the faceline and each surface point varies continuously, so that the direction and rate of movement for each surface point differ. In the following sections, the movements of each surface point on the major cross section are illustrated. 3.2 DYNAMIC SURFACE MOVEMENTS Dynamic surface movements include dynamic subsidence and displacement. The movement of each point on the subsidence basin is different as the face advances from 1 to 6 (Fig. 3.2). Surface points A and B, being far in front of the moving face, subside and displace toward the face (i.e., from A to A' and from B to B'). Point C, which is quite near but in front of the moving face, subsides continuously but displaces initially toward the face and then turns to pure subsidence ending up at C'. Point D, which is behind the face above the gob, subsides continuously, but displaces initially toward the face when it is in front of the face and reverses to follow the moving face when it is behind the face, with the amount of displacement toward the face being larger than that following the face. As a result the net displacement is toward the center of the gob (i.e., from point D to D'). The same statement is true for point E. For point F, the net displacement is zero, i.e it appears to have dropped down vertically to F'. For points G to I, the net displacements are in the direction of face advance except the magnitudes are increasing in sequential order. Point 1, has reached the final dynamic position of 1'. In other words, the face has passed sufficiently away such that it does not affect the movement at point I. All other points (A to H) are still within the face influenced area. 3.3 DEVELOPMENT OF DYNAMIC SUBSIDENCE PROFILES When the face has moved for a distance of h/6-h/3 from the setup entry, surface subsidence reaches the surface. At this time the surface subsidence basin is very mild (S, in Fig. 3.3), and it is symmetrical about the center. As the face continues to advance, the maximum subsidence continues to increase, and its location moves with, but falls farther behind the face. When the face has advanced a sufficient distance, e.g., (0.9-2.2)h, away from the setup entry, the maximum subsidence reaches the maximum possible value (curve S,). At this time, the dynamic subsidence profile is fully developed. Thereafter both sides of the dynamic subsidence profile become stabilized. The subsidence profile on the face side moves with the advancing face in an orderly manner (curves S, and S,). When the face stops, the face side of the profile continues to subside and becomes stabilized (curves;) sometime after. Curve S; is the final subsidence profile (see Fig. 2.22). 3.4 DEVELOPMENT OF DYNAMIC DISPLACEMENT AND SLOPE PROFILES The dynamic displacement profile moves with the advancing face (Fig. 3.4), but changes according to some specific rules. When the face has advanced to A, the surface begins to move and its dynamic displacement profile has two maximum values (curve Ua): one positive near the setup entry moving toward the face advancing direction and the other negative on the face side also moving toward the face advancing direction. As the face continues to advance, the positive maximum displacement on the setup entry side increases and moves toward the face continuously. The same statement is true for the negative maximum displacement on the face side. When the opening increases to the critical size, both the maximum positive and negative displacements reach the peak values and remain constant thereafter. Notice that when the opening becomes critical in size, the point of zero displacement no longer moves with the advancing face. Rather it spreads into an area of zero displacement (curve Ue) and expands as the face advances. When the face stops, the displacement on the face side continues until it becomes stabilized (curve Úe). Curve Úe is the final displacement profile. The ratio of maximum dynamic to final displacement ranges from 60 to 75%. The dynamic slope profile follows the same patterns of change. The ratio of maximum dynamic to maximum final slope ranges from 50 to 80%. The maximum slope decreases with in- creasing rate of face advance (Peng and Geng, 1984). It must be pointed out that except for those near both sides of the profiles, each point on the displacement and slope profiles is subjected to a cycle of positive and negative displacements and slopes depending on its relative position with respect to the face.

Jan 1, 1992

By Santosh Kumar Ray, DEBASHISH MISHRA, Niroj Kumar Mohalik, SOMU MANDAL, Jai Krishna Pandey, Asfar Mobin Khan

Coal is a low-cost and high-calorific-value fuel. The coal mining industry worldwide has been suffering from severe accidents due to coal dust explosion hazards since its inception. Statistically, it was observed that 12,489 fatalities had occurred in 104 reported mining accidents from coal dust explosions during 1900–2020. There are numerous methods for detection, prevention, and control of coal dust explosions in mines. The underground mining environment is unpredictable and has an array of variables. These undulating factors make it difficult to prevent or control the coal dust explosion hazard. However, coal mining is done aggressively throughout the world, especially in developing countries as coal is a major source of thermal energy used in power plants contributing to about 38% (IEA, (2019), World Energy Outlook, IEA, Paris https:// www. iea. org/ repor ts/ world- energy- outlo ok- 2019.) of world electricity. Worldwide, coal dust explosibility studies are carried out in experimental mines, laboratories, and simulations. The complexity, lack of proper infrastructure, and unavailability of laboratory equipment sometimes make it difficult to study coal dust explosibility. The authors have discussed in detail and proposed that the CFD modelling can be a viable option for studying and evaluating coal dust explosibility.

Jun 29, 2022