Search Documents

By J. D. Potts

Dust surveys were conducted at six underground coal mines to determine if deep-cutting practices expose face workers to higher levels of respirable dust. The surveyed mines were able to successfully mine deep cuts without significantly increasing the dust exposures of face workers. For exhausting face ventilation, field data indicate that scrubber airflow is the most important factor for controlling dust. Data collected for this study indicate that 20-mesh screens should be cleaned for every 40 ft of advance because 22% of the deep cuts surveyed for this study experienced a 20% to 35% decrease in scrubber airflow over the course of the cut. For blowing face ventilation, field data and past research indicate that dust control is aided by maintaining a proper curtain-to-scrubber airflow ratio of 1.0 (measured before scrubber activation) as well as a curtain setback distance that allows the miner operator to stand at the mouth of the curtain for the entire cut. Dust levels on the bolting faces did not appear to be affected by the longer cycles associated with deep-cut mining when good ventilation practices were used.

Jan 1, 2011

By J. Drelich, C. L. White, Ch. Zhou, W. M. Cross, E. T. Zellers, E. M. Nadorny

A laser-based particle deposition (LBPD) technique has recently been developed at Michigan Technological University for patterning mesostructures made of nanoparticles and their clusters. The LBPD technique makes use of laser induced optical forces to transport and pattern nanoparticles on a variety of conductive and non-conductive substrates from nanoparticle-in-liquid suspension. A weakly focused laser beam is used to confine and propel particles along the laser beam. Confinement is accomplished by forces due to optical field gradients that act on polarizable particles and tend to move them to axis of the laser beam. The force propelling the particles along the direction of the laser beam arise from momentum conservation of photons scattered from the particles. In this paper, this novel LBPD technology is briefly reviewed, and several examples of patterning are presented. The size and morphology of mesostrips produced from gold and polystyrene nanoparticles, under a range of deposition conditions, have been characterized by optical microscopy, atomic force microscopy, and scanning electron microscopy. The results presented here demonstrate that gold and polystyrene nanoparticles deposited by LBPD can form clusters of particles. When deposited at an appropriate rate, such clusters can form multilayer mesostrips of high particle density. One goal of research on such systems is to fabricate arrays of parallel lines made up of colloidal particles having a range of surface functionalities. Such arrays have potential for application as novel microsensors for environmental sensors.

Jan 1, 2003

This report is the 25th in a series summarizing Bureau of Mines research and technologic work on coal and related investigations, and the 7th of these reports to be issued on a calendar-year basis.3 It reviews briefly work in progress during 1960, and furnishes references to publications by Bureau personnel during 1960 and also to a few older papers that were not cited in prior reports of this series. Details about some of the researches mentioned can be found by referring to the publications cited in the footnotes or in the further list in the Miscellaneous section; other phases of work are reported here for the first time and will be covered in more detail by later publications, Coal programs of the Bureau of Mines extend over the wide range of theoretical and applied studies indicated by the table of contents. Fundamental research on coal structure and on the properties of coal will, over a period of time, increase the general knowledge about coal Which scientists and engineers may use in answering practical questions and in solving problems in the mining and utilization of coal. More applied studies are conducted in connection with the developement and evaluation of new mining techniques and the effective processing and utilization of coal and of coal products. Health and safety activities, analyses of coal being mined, and technical advice and assistance to Federal agencies in connection with fuel and boiler-water problems are among the practical services handled by the Bureau.4 5

Jan 1, 1962

By D. Boshoff

The ability of an explosive to break rock is influenced considerably by the extent of confinement in the blasthole. It is believed that confinement is improved by the use of adequate stemming. The aim of this paper is to present the results of the first and second stages of developing a stemming performance testing rig for small diameter boreholes. The rig was used to compare and contrast the performance of different designs of products. The results showed that different stemming products have differences in terms of their functionality, which can have a major impact on the efficiency of rock breaking. Two test procedures were used, one through the exclusive use of compressed air and the second using a purpose-built high pressure test rig with small quantities of explosives. Both tests were used to identify and evaluate the ability of various stemming products to resist the escape of explosive gas through the collar of a blasthole. An investigation was done to determine the types of stemming products most commonly used in South African underground hard rock mines, and these products were used during the tests. The first stage of tests using compressed air only did not prove adequate to predict with certainty the pressure behaviour in the borehole of a particular product under high pressure conditions. The purpose-built high pressure test rig also did not prove to be a very effective tool to test stemming products under high pressure conditions. The test rig incorporated only the effect of gas pressure on the stemming product, and excluded the effect of the shock wave. This study therefore proved that to take into account only the gas pressure generated in the blasthole is not sufficient to effectively test stemming product performance.

Jan 1, 2011

The cyclone, or centrifugal separator, ,is firmly established in industry as a low cost separator of solids from gases.While it will also separate fluids of different densities, and solids from liquids, its main use is to remove relatively fine dusts from gases whose pr~erties are generally not greatly different from those of air. This latter phase of operation is the one that will be dealt with here.The duty of such a cyclone separating system is to take in a supply of dusty gas and separate it into its components of dust and clean gas as perfectly as possible for the least consumption of pressure head. Any separation at all causes pressure loss and, in general, the greater the separation, the greater the pressure drop needed to effect it. The percentage of dust in suspension which is separated from the gas-dust mixture is commonly called the collection or separation efficiency. Overall or "true" efficiency must take pressure drop into account and may be considered as proportional to the ratio of the percentage of dust collected to the resultant pressure drop. For any cyclone It will vary with different dusts.Many commercial adaptions of the simple cyclone are made solely on the basis of pressure drop improvement, without taking into account the effect on separation efficiency, probably because the latter is so difficult to assess correctly. It appears unfortunate but true that the majority of such adaptions and patent gadgets fitted to cyclones which decrease pressure drop, do have an adverse effect on separation. In other' words, the true efficiency is seldom increased but often diminished.Without a knowledge of what actually goes on inside a cyclone, it is impossible fully to appreciate the real effect of a modification. For instance, it is on record that a cyclone...

Jan 1, 1949

By T. B. Counselman

"C" VERYONE who has to calculate cyanide circuits, -¦-' using either thickeners, filters or both, realizes the headaches involved in solving a set of simultaneous equations. When you calculate a large number of these, based on experimental data, trying to arrive at the best flowsheet, you can spend days at the task. T. B. COUNSELMAN, Member AIME, is Manager, FluoSolids Division, The Dorr CO., Stamford, Conn. AIME New York Meeting, Feb. 1950. TP 2783 B. Discussion (2 copies) may be sent to Transactions AIME before March 31, 1950. Manuscript received Aug. 23, 1949. Herewith is presented a short method, equally accurate with the standard simultaneous equation method, and much quicker. Here for instance is the standard simultaneous equation method, for 100 tons per day of $10 ore, with the conditions assumed as below (fig. 1). Conditions Assumed a. 100 tons of ore per day crushed in cyanide solution. b. Discharge from all thickeners with 50 pct moisture. c. $10 value dissolved per ton of ore. d. 50 pct in mill and 50 pct in agitators. e. 400 tons of solution from thickener V precipitated to $0.02. f. Agitation with a dilution of 2 of solution to 1 of solids. g. Let V, W, X, Y and Z represent value in dollars per ton of solution discharged from the resvective thickeners. Equating Out of and Into Each Thickener 1. lOOVplus 400V = 500W plus (0.50 X $10 X 100) 2. 1OOWplus 600W= 500X plus lOOW plus (0.50 X $10 X 100) plus lOOV 3. lOOXplus 500X = 1OOWplus 500Y 4. 1OOY plus 500Y = 1002 plus 1OOX plus (400 X 0.02) 5. 100 Zplus l00Z = l00Y plus 100 tons of water (value $0.00) Simplifying: 1. v = W plus 1.00 2. W = X plus 1.20 3. X = Y plus 0.24 4. Y = 0.2Zvlus 0.064 5. 2Z= Y

Jan 1, 1951

By T. B. Counselman

"C" VERYONE who has to calculate cyanide circuits, -¦-' using either thickeners, filters or both, realizes the headaches involved in solving a set of simultaneous equations. When you calculate a large number of these, based on experimental data, trying to arrive at the best flowsheet, you can spend days at the task. T. B. COUNSELMAN, Member AIME, is Manager, FluoSolids Division, The Dorr CO., Stamford, Conn. AIME New York Meeting, Feb. 1950. TP 2783 B. Discussion (2 copies) may be sent to Transactions AIME before March 31, 1950. Manuscript received Aug. 23, 1949. Herewith is presented a short method, equally accurate with the standard simultaneous equation method, and much quicker. Here for instance is the standard simultaneous equation method, for 100 tons per day of $10 ore, with the conditions assumed as below (fig. 1). Conditions Assumed a. 100 tons of ore per day crushed in cyanide solution. b. Discharge from all thickeners with 50 pct moisture. c. $10 value dissolved per ton of ore. d. 50 pct in mill and 50 pct in agitators. e. 400 tons of solution from thickener V precipitated to $0.02. f. Agitation with a dilution of 2 of solution to 1 of solids. g. Let V, W, X, Y and Z represent value in dollars per ton of solution discharged from the resvective thickeners. Equating Out of and Into Each Thickener 1. lOOVplus 400V = 500W plus (0.50 X $10 X 100) 2. 1OOWplus 600W= 500X plus lOOW plus (0.50 X $10 X 100) plus lOOV 3. lOOXplus 500X = 1OOWplus 500Y 4. 1OOY plus 500Y = 1002 plus 1OOX plus (400 X 0.02) 5. 100 Zplus l00Z = l00Y plus 100 tons of water (value $0.00) Simplifying: 1. v = W plus 1.00 2. W = X plus 1.20 3. X = Y plus 0.24 4. Y = 0.2Zvlus 0.064 5. 2Z= Y

Jan 1, 1951

By Patrice Favreau

In 1990 the Noranda Technology Centre commenced a project to develop an interactive three-dimensional blast design system using a commerical computer-aided drafting and design package (CADD). The objective was to alleviate the blast engineer from the tedious and time consuming blast layout and design functions normally done by hand. This would allow more time for optimizing blast designs through assessing multiple options. Since several blast design software "tools" already existed at Noranda, the need arose to integrate all the applications into one overall system that shared one common database. The result is BLASTCAD.

Jan 1, 1992

By Robert Labbe

The final tunnel lining for this project involved pumping vast quantities of concrete over large distances under the extremely busy streets of lower Manhattan. Approximately 68,000 cubic meters (89,000 cubic yards) were pumped from various locations over 152 meters (500 feet) below ground (Figure 1) to create nearly 14.5 kilometers (9 miles) of 3.05 meter (10 foot) diameter tunnel. Total distances pumped exceeded 1,645 meters (5,400 feet) horizontally after a vertical difference of over 152 meters (500 feet). The urban setting of the operation, coupled with the long distances over which concrete was pumped, created many problems which had to be dealt with along the way. A three-shift labor operation was implemented to allow sequential pouring of tunnel sections nearly every day. The fine tuning of the mix design was critical to make this operation successful.

By J. R. Kyte, L. A. Rapoport

The material balance equation for partiai or complete 1:trter-drivc reser1,oir.s been re-arranged to include a pressure irrferferencr ternr. This pressure interfernce term was ohtained from the theory established hy Morinda. A .successful progranl deissed to solve the resrclritlg c,qrration in a few hours on a nleelitr .sizeti, digital compuier. No prior knowdelge of the properties of the eqrrifer is required in the solution. 7' ri~rl calculations areatle using various assumed con!binuiions of value of the constant expretsing the qquifer properties correspoinds to the best fit ohtained between observed and calculated field history. Details of the method of calculaion are illus trated by an example. INTKCDUCTICN A method 01' calculating the material balance equation for a partial water-drive reservoir completed in an aquifer has been described in the literature." Pressure interference i'rc,m other pools iocated in the same nquiucr is not taken into account in this solution. When present, the pres- sure interference effect must be included in order to make a complete performance analysis. A correction for this effect has been developed using the theory cstahlished by Mor-tada.' Manual calculation of the material balance for water-drive reservoirs is a formidable task. Such manual ca1culation when interference eflects are includcd would be impossible to completc in any reasonable time period. However, a medium-sized stored program, digltal conlputer can he used satisfactorily. The method is described in the following sections. THECKETICAL CONSIDEKATIOhS The material balance equation for a reservoir producing by partial or total water drive, as proposed by Van Everdingen, This relationship is linear for Z/a from which thc slopc, Z, and the intercept, N, can be obtained by the least-squares method from the data points. It is not necessary lo know the aquifer properties to uktain oplimum values tor 2nd IV. Various assumptions are made tor At,,: where 11 is production time, seconds (oilfield between the equal successive time intervals into which the history is divided. t,, h It, times the number of equal time periods from i.e.. the total dimen-sionless time interval from It is noted that the dinlensionless time interval, At,,, involves all the relevant aquifer properties. Accordingly, any assunlption of is an assumption of the combined aquifer properties which pertain to the solution of the equation. Deviations of the data points from a straight line arc calculated for each assumption of and the value of A, correspond ing to the minimunl deviation is chosen as the optimum solution. This method is described in Ref. 1 and 2. Thc material balance solution is usually made with an initial assumption that the reservoir being studied is located in an infinite aquifer from which there are no other withdrawals. Deviation of the points by amounts greater than can be attributed to inaccuracies in field data may be the result of: (1) boundary effects of a limited aquifer, (2) pressure interference from othcr pools completed in the .sarne aquifer, and (3) a combination of these effects. Differentiation of these effects can be made only on the basis of geologic data. Pressure interference from other fields will result in a pressure drop at the original oil-water boundary having an interference component, The measured instantaneous pressure drops at the oil-water

Whilst the wider community is both a large consumer of mineral products and relies on mineral exports for much of the wealth which sustains it, the community generally has a poor perception of the minerals industry.   The role of professionals and The AusIMM in the "New Economy" minerals industry is reviewed. The new structure of The Institute is vital as we move forward in times of globalisation, rationalism, increasing litigation, criminalisation of risk and increased focus on corporate governance. This address looks forward to ways The AusIMM and professionals of the future are positioning themselves for these and other challenges.

Jan 1, 2001

By Robert B. Fulton

The use of industrial minerals by the chemical industry as raw materials for manufacturing and in processing spans a wide assortment of minerals. This chapter aims to supplement rather than duplicate the commodity chapters. Its objective, to describe the uses of industrial minerals in the manufacture of chemicals, is attained by considering minerals used by the chemical industry in terms of the chemical element required and by giving particular emphasis to market factors. The mineral aspect, which is covered in the commodity chapters, is subordinated and attention is focused on the chemical and market aspects. Condensing this broad subject into a few pages permits treating only the most important elements derived from industrial minerals. The elements derived from petroleum, hydrogen and carbon, which quantitatively dominate as raw materials for the chemical industry, are omitted, as are the metallic elements and the minerals covered in other "use" chapters such as phosphorous, potash, and nitrogen for fertilizers and titanium dioxide for pigments. After eliminating on this basis, our definition leaves six elements of major importance: boron, bromine, chlorine, fluorine, sodium, and sulfur. These elements are treated individually under separate headings. Salt brines have particular importance as raw material sources for the chemical industry as shown in Table 1 "Salt Brine Derivatives" (Anon., 1967), which charts the chemical compounds derived from four types of brines: (1) Owens Lake type brines which are sources of boron and sodium compounds; (2) Midland type brines from which bromine, iodine, and chlorides of calcium, magnesium, potassium, and sodium are derived; (3) Searles Lake type yielding boron, bromine, lithium, magnesium, potassium, and sodium compounds; and (4) Silver Peak type produced mainly for lithium. Table 2 (Jones, 1973) affords an overview of the chief industrial minerals, the chemical products derived from them, and end uses of the products.

Jan 1, 1975

By Jerry B. F. Champlin

The successful injection of liquids into subsurface permeable formations for production stimulation, storage, or waste disposal requires a rapid, precise, and accurate method of determining the permeability of porous solids. This report describes a method and apparatus, developed by the Bureau of Mines, that use the principle of specific-volume permeametry. Calibration of the apparatus over a wide range of permeabilities and standardization of several apparatus constants have eliminated many of the tedious calculations and problems of manipulation common to some other methods. Improvements in reproducibility and accuracy have resulted from reducing experimental measurements to one parameter--time. Specific permeabilities of reservoir rock samples are determined directly from a chart that relates elapsed time to a permeability equivalent to that determined by bubble-tube measurements.

Jan 1, 1962

By H. J. Levinstein, H. J. Guggenheim, C. D. Capio

An optical incestigation of the phase transformations in RbFeF, has been conducted. Details of the ferromagwetic phase transition and the metamagnetic state are disczrssed. The three-dimensional magnetic domain structure existing in bulk crystals of RbFeF3 is described, as well as the effect of the magnitude and direction of the applied magnetic field on the domain struclure. The strong magnetoelastic interaction in RbFeF, is demonstrated. The results of the direct observation of the role of dislocation subboundaries and slip bands as nucleation sites and as pinning sites for magnetic domain walls are reported. THE perovskite compound RbFeF, has recently been shown to exhibit three magnetic states.''' Above 102°K it is paramagnetic, between 102" and 87°K it is antiferromagnetic. and below 87°K it is ferromagnetic (i.e., exhibiting remanence) with a modification of the magnetization occurring at 40°K. The changes in magnetic structure at 102o, 87°. and 40°K are accompanied by shear transformations to successively lower crystal symmetry classes.3 At 102°K a second-order phase transformation to a tetragonal crystal structure occurs. The c/o ratio increases with decreasing temperature to a value of 1.0034 at 87°K where the crystal undergoes another shear transformation to an ortho-rhombic crystal structure. The magnetic modification at 40 K is also accompanied by a shear transformation to a lower crystal symmetry. RbFeF3 is unique in that in the ferromagnetic state it is transparent in the bulk to visible light, has a low saturation magnetization, a large magnetic rotation. and has good optical properties.' All these features make it an ideal material for the investigation of magnetic domain structures in bulk crystals. In addition a dislocation etch has been developed which reveals the point of emergence of dislocations with the (100) surfaces of RbFeF3,5 making it possible to determine the dislocation arrays in the material. As a result domain wall dislocation interactions can be observed in the bulk crystal. In this paper we report on 1) the crystallography of the phase transformations in RbFeF3. 2) the domain configurations as a function of magnetic field and crystal orientation. 3) the interaction of dislocations and magnetic domain walls in RbFeF,. EXPERIMENTAL PROCEDURE Since the temperature range of interest is below room temperature the dewar shown in Fig. 1 was employed. It was designed to fit on the stage of a Leitz panphot metallograph, and permitted examination of the sample at a magnification up to 150 times. The dewar consists of a double-walled glass cylinder bent into an L shape. The space between the walls is evacuated. The viewing wirldows were made of four optically flat quartz discs aligned parallel to each other and sealed to the sides of the concentric cylinders. The specimens were mounted in a holder attached to a flexible plastic shaft. Various holder designs were employed depending upon the type of observations to be made. For studies of the phase transformation between the antiferromagnetic and ferromagnetic state the holder shown in Fig. 2(d) was employed. This holder permitted accurate temperature control at 82" to 88°K by balancing the heat input from the carbon resistance heater against the heat loss to a heat sink immersed in liquid N2. Magnetic field studies were conducted by employing the holders shown in Figs. 2(a) and (b). The holder shown in Fig. 2(n) has a solenoid imbedded in it. such that the magnetic field direction is in the same direction as the incident light. The magnetic field provided by the holder in Fig. 2(b) is perpendicular to the incident light direction. The holder in Fig. 2(r) was employed when observations of the specimen were desired while an elastic bending stress was applied to the sample. The stress was applied to the sample by pulling a wire from outside of the dewar. The wire was attached to a lever pivoted on the holder. which caused the knife edge of the lever to push against the sample. The crystal growth and the sample preparation were described previously.' PHASE TRANSFORMATIONS The first phase transformation in this system is from the cubic perovskite structure to n tetragonal

Jan 1, 1970

By Barnard Foo

Topics of Discussion ?Location ?Production & Mining Operation ?Mineralization ?Mining Method ?Rock Mechanics Issues ?Ground Control Problems ?Numerical Analysis ?RockmassBehaviour ?Conclusions & Recommendations ?Discussion

Feb 1, 2008

By Foster Fraas

The most important lithium resource in the United States is in the form of the feldspathoid mineral spodumene. This mineral has not been used to any important extent as a source of lithium salts or lithium metal, as other more easily decomposed minerals have b en available in sufficient quantity to supply the relatively small demand. The need for cheaper lithium salts for such promising new uses as air conditioning or dehumidification and of lithium feldspar for use in the glass and [ramic] trades has justified the recent work done by the Bureau of Mines on King available, through improved beneficiation and extractive processes, some of the lower grade but extensive spodumene deposits.

Jan 1, 1937

By Foster Fraas

The most important lithium resource in the United States is in the form of the feldspathoid mineral spodumene. This mineral has not been used to any important extent as a source of lithium salts or lithium metal, as other more easily decomposed minerals have been available in sufficient quantity to supply the relatively small demand. The need for cheaper lithium salts for such promising new uses as air conditioning or dehumidification and of lithium feldspar for use in the glass and [ramic] trades has justified the recent work done by the Bureau of Mines on [king] available, through improved beneficiation and extractive processes, some of the lower grade but extensive spodumene deposits.

Jan 1, 1937

By M A. Rhamdhani, K Avarmaa, A Putera, J Chen, G Brooks

Silicon-based photovoltaic cells are currently the most dominant types applied to convert solar energy to electricity. In solar-grade silicon (SG-Si), the control of boron (B) and phosphorus (P) is very critical. Generally, these elements are difficult to remove into acceptable sub-ppm levels from lower grade Si. This study investigates slag treatment as a process for Si refining, focusing on the behaviour of P and B. The experiments were conducted by equilibrating Si-B-P alloys with 43 wt per cent SiO2 – 47 wt per cent CaO – 10 wt per cent Al2O3 slag under inert atmosphere at 1500°C. Different crucible materials were used (Al2O3, SiO2 and MgO), which determined the primary saturation phase for the system and modified the final slag composition accordingly. The samples were equilibrated and analysed with microanalysis techniques (EPMA (electron probe microanalysis) and LA-ICP-MS (laser ablation inductively coupled plasma mass spectrometry)). New standards were prepared and applied in the LA-ICP-MS analyses. Experimental results show that silver is essentially fully dissolved in silicon, as well as most phosphorus with LP ( = wt per cent P in slag/wt per cent P in Si) between 0.1–0.3. The distribution coefficient of boron was measured to be between 1 and 2. The crucible material used had an influence on the phase compositions and slight influence on the distribution coefficients of boron and phosphorus. The experimental results provided new accurate data when considering applicability of slag treatment as a technique for Si refining and Si PV cell recycling.

Jun 19, 2024

By J. F. Papp

The microstructures of a CF2Br2-inhibited methane flame and its uninhibited analog have been determined using molecular beam-mass spectrometry. The slightly lean flames were stabilized on a cooled porous plug burner at reduced pressure. Composition profiles of stable, intermediate, and radical species and temperature profiles were obtained. Comparisons of the uninhibited and inhibited flame profiles revealed the following inhibition effects; a shift of the primary reaction zone to higher temperatures, a higher maximum flame temperature, an increase in the CH3 concentration, and a reduction in the H2CO, H, 0, and OH concentrations. Kinetic analyses of the data yielded rate coefficients at flame temperatures for the reactions H + CH4 ? CH3 + H2, H + O2 ? OH + O, CO + OH ? CO2 + H, and CH3 + O ? H2CO + H. CF2Br2 is judged to decay by thermal decomposition and abstraction reactions.

Jan 1, 1981

By Ramdane Bahar

"Abstract The design foundations can be performed using Menard pressuremeter rules that require a limit pressure and a pressuremeter modulus. In recent years, another trend of interpretation of this test is appeared. It consists of identifying the rheological soil parameters using analytical or numerical methods and then used to evaluate the bearing capacity and settlement of soil foundations using numerical software. This paper deals with the bearing capacity and settlement predictions of bored piles using two approaches. The first one is the method called ""Pressident"" which is a numerical program developed to analyse pressuremeter tests taking into account the Duncan and Chang model. The second approach is the method developed by Bahar and Olivari based on the generalised elastoplastic Prager’s model with the Von Mises criterion which is suitable to describe the behaviour of saturated clays under undrained conditions. The pressuremeter data, collected on various research and consulting projects are used to explore the relationship between limit pressure and undrained shear strength obtained by the two methods. Numerical calculations, by FLAC2D software taking into account the rheological parameters derived from these two methods, are performed in order to predict the behaviour of a single bored pile subjected to an axial vertical load. The predictions are comparedto the measured data.IntroductionThe Menard Pressuremeter test has been used extensively to measure in situ soil properties and for the design deep foundations in Algeria. These tests are an useful and economical way for obtaining reliable in situ properties of soils and provide the measurement of in situ stress-strain response of soils. From this test, the design foundations can be performed using pressuremeter rules that require a limit pressure, pl, and a pressuremeter modulus, EM. These two parameters are derived from the pressuremeter curve or deduced from existing correlations with undrained cohesion and internal angle friction (Ménard, 1957; Amar and Jézéquel, 1972), and are used to evaluate the bearing capacity of soil foundations and the expected settlements. But, they can also help to identify usual soil parameters required by simple constitutive models for soils in numerical calculations."

Jan 1, 2014