Search Documents

By A. D. Storrie

An underground wet shotcrete trial was completed last year to determine the effectiveness of wet shotcrete as an alternative support mechanism to dry shotcrete in the kimberlite environment. The wet shotcrete was manufactured at the underground batch plants, transported to site using an agiecar and transferred to the shotcrete pump. The wet shotcrete is pumped to the nozzle where compressed air at 7 bar and an accelerator, Meyco SA 160, is added and enables the shotcrete to be placed successfully onto the tunnel wall. No tunnel guard was previously placed on the sidewall and hangingwall. Geotechnical testing indicates that the Grace fibre performed extremely well with the energy absorption tests at 7 kg/m3and 8kg/m3where both achieved over the mine requirement of 750joules. The Grace fibre and wet shotcrete mix also achieved a compressive strength in excess of 55 MPa, well above the 45 MPa requirement for Premier Mine. The recommended wet shotcrete mix design is therefore based upon: [Material/ CriteriaQuantity/m3Units ?Lafarge 42.5 Duratech500kg ?Condensed silica fume40kg ?Rayton Sand1.558Ton ?Delvocrete stabilizer 103.6litres ?Glenium 27CH5.4litres ?Meyco TCC 7355litres ?Water230litres ?Meyco SA16025litres ?Fibre8kg ?Cement/Water Ratio2.35? ?Water/Cement Ratio0.43? ?Flow615 mm] If the wet shotcrete system is implemented there is a potential for Premier Mine to make major savings. In South Africa there are two suitable wet shotcrete machines available for the mining industry, the Spreymec, manufactured by Tamrock and the Fermel/Meyco wet shotcrete machine. The Spreymec is a fully imported machine. The Fermel component is manufactured in South Africa and the Meyco shotcrete components are imported and supported by MBT (Master Builder Technologists) in South Africa. The Fermel/Meyco machine is assembled in South Africa. Premier Mine has allocated some R2, 100,000 towards the implementation of the wet shotcrete system. If implementation is successful there should be an internal rate of return gain of 76% with regard to this project.

Jan 1, 2001

By Russel Delmar, Rick Everdell, Harry Charalambu, John Tait

Award of the Design/Build Agreement for construction of Ontario Power Generation’s (OPG’s) Niagara Tunnel Project was made after an intensive 8-month international procurement process. The 14.4-m diameter × 10.4-km long rock tunnel will divert 500 m3/s of water from the Niagara River to the Sir Adam Beck hydroelectric generating complex. The procurement process and Design/Build Agreement included features to address the owner’s requirements regarding risk allocation and cost and schedule certainty, while encouraging innovative ideas from the industry, both technically and commercially. The process included an international expression of interest and prequalification, followed by an invitation for design/build proposals to qualified proponents, and comprehensive proposal evaluations and negotiations with several respondent proponents. An honorarium was provided to the unsuccessful participants in the proposal stage. The resultant negotiated Design/Build Agreement includes Owner’s Mandatory Requirements, negotiated contract terms and conditions, performanceincentive bonuses and liquidated damages for schedule and water delivery performance, a multistaged Geotechnical Baseline Report, joint risk management, references to preexisting community impact agreements and measures to reduce impact on tourism. It also addresses regulatory approvals and permits, an owner controlled insurance policy that required reference to the International Tunneling Insurance Group (ITIG) Code of Practice for Risk Management as a condition of coverage, site specific safety, security and environmental plans, formal team building, a dispute review board, and escrow documentation.

Jan 1, 2007

By E. H. Rose

From the more distant members and some not so distant, the plaint is often heard that they cannot justify the expense and time required to attend the AIME Annual Meeting. Almost invariably, the reason given takes this form: "I just don't see that I would get enough out of it." Often the would-be clincher is added: "Besides, the meat of it all comes out in print anyway." Not long ago, a group of us who have seldom missed a meeting in recent years fell to discussing this phenomenon, and found ourselves in emphatic agreement that anyone holding such a belief indicates by his first remark that he does not know how to attend a convention, and by his second, proves it. He is, by and large, the man who has never been there, and of him, there are many.

Jan 1, 1949

By M. B. McClenaghan

"Abstract - The Matheson area of northeastern Ontario is of great interest for mineral explo­ ration because of its geological similarities with the adjacent Timmins, Kirkland Lake and Larder Lake gold camps. Exploration in the area, however, is hampered by the presence of an extensive and thick cover of glacial sediments. For this reason, till geochemistry has be­ come an important exploration method. The Ontario Geological Survey&apos;s Black River -Matheson (BRiM) reconnaissance till sampling project, carried out between 1984 and 1988, was designed to aid exploration in the Matheson area by documenting the Quaternary stratigraphy and providing a database of till geochemistry. Till samples were collected by backhoe trenching of surface pits in areas of thin drift ( < 5 m) and by sonic overburden drilling in areas of thicker drift. This paper summarizes the results from the shallow till sampling component of the BRiM project.Two hundred and eighty-two surface samples were collected from Matheson Till, the youngest till sheet in the area, which was deposited during the Late Wisconsinan. For each sample, the non-magnetic heavy mineral (>3.3 S.G.) and fine (-250 mesh) till fractions were analyzed geochemically. In addition, visible gold grains were recovered by panning the heavy mineral fraction. Five areas that display multi-element anomalies in both till fractions warrant further investigation: (1) western Egan Township, overlying the Bradley Lake Syenite; (2) around and south of the Munro and Croesus mines, in Munro and Guibord townships; (3) central Garrison Township overlying the Garrison Stock; (4) south of Ore Car Lake in northern Thackeray Township; and (5) southeastern Harker Township. In these areas, Matheson Till has a local provenance and the bedrock sources for these anomalies are nearby in the up-ice (north­ northwest) direction. Due to the fine-grained nature of gold in bedrock deposits in the BRiM area, the small size of most gold grains recovered from till samples (<50 1-1m) and the variable distribution of gold in the heavy mineral concentrate and fine fractions, the fine fraction in addition to the more commonly used heavy mineral concentrate should be used for gold exploration.Surface till samples have been affected by weathering to a depth of s3 m. Weathered till is characterized by a very low carbonate content in the matrix fraction, the absence of sulfide grains in the heavy mineral concentrate and higher concentrations of copper, nickel and zinc in the fine fraction than in the heavy mineral concentrate. As a result of the weathered/ oxidized nature of the surface till samples, the fine fraction is a better sampling medium for base metal exploration."

Jan 1, 1992

By Rapheal Trousselle

For over 5 years, Davey Bickford has been developing and testing an electronic detonator blasting system. These new-technology detonators provide more accurate timing than conventional systems that rely on the combustion speed of a pyrotechnic composition.

Jan 1, 1997

The Waimumu area, 12 km southwest of Gore, is underlain by the Gore Lignite Measures, an early Tertiary fluvial sequence approximately 500 m thick resting on Triassic-Jurassic argillitic basement. The Waimumu Quartz Gravels (Pliocene) have been deposited locally and are in part due to the localised reworking of the Gore Lignite Measures. Structurally the area is dominated by the Dunsdale Fault System, a steeply dipping series of NE trending reverse faults (Isaac and Lindqvist, 1990). The Belle-Brook, Hedgehope and Parker Road sites sampled are adjacent to the downthrown (east) side of the Hedgehope Fault.The authigenic gold-sulphide association at Belle-Brook was discovered in 1987 (Falconer, 1987: Clough and Craw, 1989). Despite a very limited amount of alluvial mining a significant quantity of authigenic marcasite has developed. Authigenic sulphide trace element analysis has shown anomalous amounts of As, Ni, Cr and to a lesser extent Zn, Pb and eu (Table 1). It has been established that the nickel occurs as a colloform banded Ni sulphide, possibly bravoite, within the marcasite (Figures 1 &amp; 2). Arsenic and nickel (re)mobilisation are well documented in the literature. Generally As and heavy metals are mobilised in the groundwater as a result of the oxidation of sulphides (ie as a result of mining). At Belle-Brook it is reasonable to assume the authigenic sulphide trace element composition reflects either localised groundwater contamination or hydrothermal mineralisation. This poster presents some preliminary findings.

Jan 1, 2001

By H. F. Niemand, C. J. Postma, P. L. Crouse

"SynopsisThe separation of zirconium and hafnium is essential in the nuclear industry, since zirconium alloys for this application require hafnium concentrations of less than 100 ppm. The separation is, however, very difficult due to the numerous similarities in the chemical and physical properties of these two elements.Traditional methods for separation of zirconium and hafnium rely predominantly on wet chemical techniques, e.g. solvent extraction. In contrast to the traditional aqueous chloride systems, the AMI zirconium metal process developed by Necsa focuses on dry fluoride-based processes. Dry processes have the advantage of producing much less hazardous chemical waste.In the proposed AMI process, separation is effected by selective sublimation of the two tetrafluorides in an inert atmosphere under controlled conditions, and subsequent selective desublimation. Estimates are made for the sublimation rates of the two tetrafluorides based on the equilibrium vapour pressures. A sublimation model, based on the sublimation rates, was developed to determine if the concept of separation by sublimation and subsequent desublimation is theoretically possible.IntroductionZirconium requires several purification steps to conform to nuclear-grade specifications. Little information is available on the sublimation separation of Zr and Hf compounds, especially in the fluoride form, the majority of which deals with sublimation under vacuum conditions. On the industrial scale, only vacuum sublimation of ZrF4 has been reported. No records were found for the sublimation of ZrF4 in an inert atmosphere. Information on the sublimation rate of ZrF4 or HfF4 in an inert atmosphere is also limited. The rate is assumed to be dependent on several factors, of which temperature, area, and composition are considered the most important."

Jan 1, 2015

By F. R. Cattoir

This report presents the results of preliminary studies for the evaluation of some fused-salt electrolytes for refining tungsten metal, and describes the equipment used. Some impurities could be eliminated with electrolytes composed of sodium chloride, sodium iodide, or sodium tetraborate in combination with tungstic oxide or sodium tungstate. Electrolytes composed entirely of chlorides were unusable because of the volatility of tungsten chloride. Refining 96-to 98-percent tungsten to produce a commercial grade was more successful than further refining of 99.9-percent tungsten. No electrolyte tested yielded a product pure in all respects. Electrolyte temperatures of about 900° C were necessary to maintain a good dissolution rate at the anode and acceptable cell operation. Cathode current densities at the beginning of a deposition cycle were limited to approximately 1 ampere per square inch. Higher current densities resulted in a finely divided product that frequently failed to adhere to the cathode. The most conspicuous impurities in the tungsten produced were carbon, iron, and molybdenum; the former two came from the iron cell and the graphite cell liner. Electrolytes com-posed of tungstic oxide or sodium tungstate in sodium iodide, or 2Na, 0.B203, were capable of producing tungsten carbide.

Jan 1, 1963

By C. G. Dunn

James, Jones, and Leak (JJL) conclude that growth-rate and orientation-distribution data obtained in a steep thermal gradient should be used with caution to account for isothermally produced recrystallization textures. I agree. However, it is not clear whether they conclude a) that the orientation dependence of rate of growth of secondaries in (commercial) silicon iron depends on both temperature and a temperature gradient or b) that, in applying rate data obtained in a steep thermal gradient, the isothermal annealing temperature must be close to the temperature for which the rate data apply. Also, it is not clear what tem-

Jan 1, 1967

By N. Fragen, H. H. Stroch

"INTRODUCTION A previous paper by H. H. Storch 4 described. three processes for the production of potassium sulphate from polyhalite (K2S01.MgSO1.2CaS04.2H2o), Since these processes depended upon calcination of polyhalite followed by leaching with water at 100°C., the fundamental reactions occurring in these steps were discussed in detail. This paper, which describes processes producing syngenite (K2S04.CaSO4.H2O) and potassium sulphate and gives data concerning the production of by-product magnesia, presents the results of work performed at the Non metallic Minerals Experiment Station of the U. S. Bureau of Mines, maintained at New Brunswick, N. J., in cooperation with Rutgers University.A study of the solubility relationships of the system 5 Ca++ -Mg++ -K+-SO4 = H20 at 25ºC. shows that syngenite is stable in the presence of a concentrated MgSO4 solution, the K2SO : equilibrium concentration being comparatively low (2.6 per cent), The processes described below, which involve the conversion of calcined polyhalite to syngenite, are based on the 25°C. equilibria. It has further been found that syngenite can be decomposed by water at 100ºC, yielding a 9 to 10 per cent K250 solution, the solid phase being potassium calcium pentasulphate (K2SO, 3CaSO.H2O, hereafter referred to as ""pentasulphate""). This latter compound is unstable in the presence of water at 25°C., its decomposition resulting in a solution containing about 3 per cent of K2SO4 and a solid phase consisting of gypsum. This behaviour of syngenite with water at 100°C. and of pentasulphate with water at 25ºC. constitutes the basis of processes for the production of K2SO4 by way of the conversion of calcined polyhalite to syngenite,Syngenite is a product which may be used as a fertilizer per se. As produced in the process to be described, it contains about 50 per cent of K2SO1, and will readily give up its potash content on treatment with water, although the limiting concentration at ordinary temperatures is approximately 3 per cent. This definite but limited solubility should make this product more desirable as a fertilizer then the more concentrated forms of potash salts which have higher solubilities and hence involve the danger or plant injury due to a high local concentration of potash."

Sep 1, 1931

By Daniel Hauer

Blocking. (5) The “blocking” of boulders is a much cheaper way of breaking them up than “mud capping.” It should always be used in preference to that method except when too much time will be consumed by a crew of men waiting for the drilling to be done, as shown in example of cost No. 1, as given under “mud capping.” Under such circumstances the time consumed would be a greater cost to the contractor than the extra amount of dynamite. Then, too, on large thin boulders to drill one hole would result only in breaking the stone into such pieces as would again have to be broken; and the many holes might equal the cost of extra dynamite. Under such circumstances if method (6) cannot be used, “mud capping” will have to be resorted to, to do the work economically.

Jan 1, 2006

By Paulo José Costa Couceiro Junior, Manuel Lopez Cano

The biggest Port of Latin America - the Santos Port in São Paulo, Brazil - has been drilled and blasted by controlled underwater techniques in order to remove around 40,000 m3 (52,318 cubic yard) of rock divided in two outcrop rocks: Teffé and Itapema. Underwater pumped explosive, in combination with small cartridges areas, was successfully used in order to reach a target depth of -15m (-49 ft) and a width of 220m (722 ft) in the navigation channel. It was the first time that a pumped explosive was used in underwater blasting in Brazil and it represents a historic benchmark for projects of this kind in this country. The main challenges faced in this project include the control of the ground vibration, due to the necessity to carry out detonations 40m (131 ft) away from the quay wall - where the passenger terminal and the 80 year-old warehouse were located – and the rush schedule available, in order to finish the underwater drilling and blasting phase before the coming cruise season. Therefore, the perfect combination of an ideal pumped product with an effective pumping system has permitted to carry out the project in a record of less time than 3 months (against to the original expected time of 18 months), with all vibration events under control as result of the special ground vibration program carried out.

Jan 1, 2016

By David A. Lipton

U.S. Bureau of Mines personnel examined mines, prospects, and mineralized areas to determine the mineral resources and potential of the Moses and Dennison Peak RARE II areas in Tulare County, California. These areas, along the west slope of the Sierra Nevada, are underlain by grarnitic rocks of the Sierra Nevada batholith and contain numerous metasedimentary roof pendants. Silver, copper, and zinc occur in contact-metasomatic deposits within the metasedimentary rocks. In the Moses area, the Powell Mine (fig. 1) contains an estimated 90,000 tons (82,000 t) of subeconomic silver, zinc, and copper resources. The King Solomon Prospect has 3,000 tons (2,700 t) of silicified phyllite containing zinc. On the Helen-Joyce Prospect, 44,000 tons (40,000 t) of gossan occur above a poorly exposed silver-zinc rich zone. Potential exists for additional mineral resources and occurrences at each of these properties.

Jan 1, 1983

By P. Tong-jiang

We studied mineralogical characteristics of the vermiculite samples from seven mines in China. We found three types of interstratified structures in the investigated samples: 1:1 regular interstratified structure, segregated interstratified structure, and random interstratified structure. The vermiculite samples from six mines are mainly composed of phlogopite?vermiculite interstratified minerals, and the samples from the other mine are composed of chlorite?vermiculite interstratified mineral. The samples with phlogopite?vermiculite structure have high contents of K2O, TiO2 and Na2O. The samples with chlorite?vermiculite structure have the highest contents of MgO and Al2O3. The cation exchange capacity of the samples is 17.3?99.0 mmol/100g.The exchangeable cations of phlogopite?vermiculite samples from Weili Mine mainly include Na+ and Ca2+, while those of phlogopite?vermiculite samples from Tongguan Mine mainly include Mg2+ and Ca2+. The thermal expansion ratio of the samples is between 9 and 32. The exfoliated vermiculite products from Weili Mine have the best mechanical strength.

Feb 27, 2013

By the use of flotation tests it was confirmed that there are two functions of oxygen in sulphide mineral flotation. Sized samples of galena and chalcopyrite were sulphidized, washed free of excess sulphide ion, and then contacted with air-saturated water for certain lengths of time. The mineral was then transferred to a sealed laboratory flotation cell containing water with a known concentration of dissolved oxygen. Xanthate and frother were added and flotation continued for 1 min.Both the extent of mineral oxidation and the concentration of dissolved oxygen markedly affected the flotation of galena and chalcopyrite. The response to a change in either variable is dependent on the level of the other, but generally best flotation occurs with the maximum degree of air saturation of the pulp. Galena flotation is hindered by oxidation of the mineral beyond a small threshold amount but a similar effect for chalcopyrite was not observed...

Jan 1, 1967

By Tracy Brettmann

Equipment ? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 2004

By J. F. Kemp

PAGE Introduction,............170 I. The Competence oF the Igneous Rocks to Supply the Materi als oF Veins,...........171 The Demonstrated Presence of the Metals in the Igneous Rocks,. . 171 The Presence of the Metals in the Sedimentary and Metamorphic Rocks, 173 Conclusions,...........175 The Abundance in Igneous Racks of Vapors or Dissociated Gases which will Yield Water on Emission and Cooling,. 175 The Sequence of Eruptions,. .. . 1 . • .. 78 The Sequence of Vein-Formations,.......1 79 Contact-Metamorphism,.........180 Pegmatites,............181 Frequency of Pneumatolitic Minerals in Veins,.. 183 Surface-Flows of Igneous Rock Unfavorable to Vein-Formation,. . 183

Jan 1, 1902

By S Adamson

Morphological analysis of alluvial gold recovered from the same segment of a placer by four common commercial methods indicates that gold shape and the presence of quartz intergrowths or sulphide overgrowths substantially influence the recovery efficiency of each method. The amount and types of gold saved by each method varies according to the different hydrodynamic conditions under which each of the methods operates. Reverse circulation drilling has the lowest efficiency and preferentially loses moderate-high flatness gold and intergrown or overgrown gold particles with relatively low density. Gravity riffle, hydraulic riffle, and jigcentrifugal concentrator systems respectively save progressively more of these problematic gold morphotypes, but still lose significant and sometimes substantial amounts (of profit) to the tailings. Because of the differences in recovery efficiency, reverse circulation drilling probably underestimates the grade of most placers and may have resulted in bypassing several economic deposits. Losses to tailings by commercial recovery plants arise from inadequacies in fundamental plant design features. These inadequacies compromise plant efficiency by limiting the ability of plants to simulate the wide range of hydrodynamic conditions necessary to operate effectively throughout placer systems. Incorporation of sand pumps and multiple recovery methods into the more sophisticated plants only partly overcomes these inadequacies. At best, efficiency will be maximised in a few segments of the placer determined by individual plant design, and will decrease progressively upstream and downstream of those segments. Without prior knowledge of the morphological characteristics of the gold to be mined, it is difficult to choose the most appropriate plant design, or to estimate what proportion of the gold will be recoverable by any given plant. If the relevant relationships are not considered beforehand, the recovery plant is likely to lose a significant proportion of the gold, and sacrifice maximum profit.

Jan 1, 2001

By Doug Anderson

Blast vibration seismograms are generally collected strictly for compliance with regulations. The peak levels (including dominant frequency) are typically all that are looked at. However, these records contain a lot more information about how a blast has performed. The seismogram is actually a record of explosive energy that was not used in fragmenting rock. The trick is to determine how to extract information that would be useful in analyzing blast performance.

Jan 1, 2013

By K. Lang

A case study is provided that highlights the successful use of high efficiency electrical submersible pumps (ESPs) adapted from the oil and gas industry for a large scale, open pit mine dewatering operation. In this case, the mine is Goldcorp?s Peñasquito Mine, Peñasco and Chile Colorado open pit development areas in Zacatecas, Mexico. At the time of publication (July 2012), there were 18 vertical bedrock dewatering wells producing an average flow rate of 350 liters per second (lps) from the Peñasco and Chile Colorado development areas. Average pumping rate per well was 18 lps, with a maximum of 44 lps. The depth of wells varies from 330 m to 500m, and includes both in-pit and perimeter (ex-pit) pumping centers. A network of 50 piezometers was used to monitor the response of groundwater levels to pumping. Since dewatering operations were initiated in 2007, groundwater elevations decreased overall, from approximately 1950 m above sea level (masl) to around 1625 masl, for a total of 340 m of drawdown. The pit floor elevation was approximately 1655 masl. All of the producing wells were constructed with 16-inch boreholes, completed with 10-inch diameter blank casing and louvered screen sections and equipped with ESPs. The application of ESPs has proven to be highly effective in the case of Peñasquito?s dewatering operations. Noted advantages include the following: ? Small diameter pump allows use of smaller diameter boreholes (16 inches) and casing / screens (10 inches) reducing well drilling and construction costs ? Greater application range for flow rate and total dynamic head ? Variable speed drive systems for greater energy efficiency and flow rate optimization ? Integration of downhole instrumentation into the motor and pump assembly The advantages and benefits of using high efficiency ESPs revolutionized the dewatering program at Peñasquito open pit mine as evidenced by the number of deep vertical well installations and high dewatering flow rates and total dynamic head requirements.

Feb 27, 2013