Search Documents

By Robert Bakish, William D. Robertson

AFTER more than fifty years of investigation and continuing failure in service, a satisfactory mechanism to explain stress corrosion cracking in homogeneous alloys is still lacking. The relative chemical activity of grain boundaries and adjacent grains, inferred from the boundary structure, has been used to explain intergranular cracking in a brass.' This concept is probably correct as a general hypothesis, but it requires much more extensive development in order to explain satisfactorily the observed phenomena. For example, the specific function of the solute in an alloy must be considered, because intergranular failure does not occur in pure metals,' which are structurally similar to homogeneous alloys. Also, in this connection, an inter crystalline fracture path in binary copper alloys can be changed to a transcrystalline path by relatively small ternary additions.' The fracture path in ß brass is predominantly transcrystalline,' in contrast with an inter crystalline path in a brass. Whether the two different fracture paths are the result of a difference in composition, crystal structure, or the state of long range order is unknown and cannot be determined with ß brass, because only the ordered state can be obtained at room temperature. The study of chemical activity at structural sites in the Cu-Zn system is restricted by the formation of opaque films in an ammonia environment in which stress corrosion cracking is generally observed. Furthermore, both components of the alloy are chemically active and the interpretation of observations is therefore relatively complicated. The Cu-Au system is a better choice for the purpose of studying structural factors. In particular, CuAu is very susceptible to cracking in ferric chloride and opaque films are not formed in this solution; it may be obtained in different states of long and short range order; and, finally, only copper is oxidized in dilute ferric chloride, which considerably simplifies the chemical problem. To provide information necessary for a more general explanation of stress corrosion cracking in homogeneous solid solutions, the following structural factors have been investigated in a Cu-Au alloy having a composition corresponding to Cu,Au: 1) the effect of long and short range order; 2) the structural sites from which copper is removed from the annealed and cold worked polycrystalline alloy; and 3) the effect of annealing time and temperature on structural reactions in the cold worked alloy. Experimental Procedure A Cu-Au alloy of nominal Cu3Au composition was cast from cathode copper and high purity gold and fabricated into sheet and wire. Chemical analysis for copper and gold indicated 48.92 wt pct Cu and 51.01 pct Au. Quantitative spectrographic analysis indicated 0.01 pct Ag, 0.002 pct Pd, 0.001 pct Pb, and 0.002 pct Fe, with traces of magnesium, silicon, and zinc. Presumably most of the remaining 0.055 pct corresponds to the limits of analytical precision. Heat treatments of wire and sheet were conducted in argon or vacuum. Wire specimens, 0.064 in. diam, were heated for 1 hr at 850 °C to establish a definite

Jan 1, 1957

By W. Greg Maybee

Separations, which form along stratigraphic boundaries in the roofs of potash mines, pose a serious safety concern. If these separations go undetected they can lead to falls of ground. The current method of identifying the location and extent of these separations is through manual scaling (sounding) using an aluminium rod. The potash mining companies would like to have a tool, which could quickly and reliably detect these separations and distinguish between them and clay seams. This paper presents the results of field trials undertaken at various potash mines in Saskatchewan belonging to the member companies of the Saskatchewan Potash Producers Association. A ground penetrating radar instrument from RST called SUSI (stepped frequency, ultra-wideband, synthetic aperture radar instrument) was used. SUSI has the ability of working over various frequency bandwidths. Four mines were chosen for these field trials, covering the different geological characteristics encountered in the Saskatchewan potash mines: Potash Corporation of Saskatchewan?s (PCS) Allan and Lanigan Divisions, Agrium?s Vanscoy Potash Operations and IMC Potash?s K2 Mine. These field trials indicated that stepped frequency ground penetrating radar technology could be ?tuned? to identify both separations and clay stratigraphy in the softrock, potash mine environment, based on the different spectral responses of the features.

May 1, 2004

By Raymond F. Farrell

A goal of the U.S. Department of the Interior, Bureau of Mines, is the advancement of minerals technology through the development of improved metals and minerals processing. In support of this goal, the Albany Metallurgy Research Center has developed atomic absorption spectrographic methods for the rapid analysis of A1203, CaO, Fe203, MgO, MnO, and Si02 in steelmaking slags. The application of these methods is discussed using an inexpensive pressure dissolution system. The overall coefficient of variation is 5 pct. The accuracy is the same as the reproducibility.

Jan 1, 1979

By C. Heckman, M. S. Moats, A. Luyima, W. Cui

"Chloride ions and their interactions with two organic smoothing additives – Cyquest® N-900 and HydroStar® 4208 – during copper electrodeposition were explored using cyclic voltammetry and electrochemical impedance spectroscopy. The results revealed that chloride ions, up to a concentration of 40 mg/L, depolarized the copper deposition reaction. A combination of chloride ions and Cyquest N-900 inhibited the depolarization reaction during copper electrodeposition. It is proposed that the chloride ions acted as bridging ligands between copper and Cyquest N-900. Addition of HydroStar at a concentration of 2.5 mg/L depolarized the copper deposition reaction when no chloride ions were present. This behavior did not change with the addition of chloride ions at the concentrations tested, indicating that chloride ions and the polysaccharide do not interact.IntroductionElectrowinning is a major production method used to obtain high-purity copper. In modern tankhouses, copper is electrodeposited onto stainless steel blanks and then stripped, washed and bundled for delivery. Significant improvements in the quality of electrowon copper have been made over the last few decades. Additives, temperature, current density, electrolyte concentrations and agitation are known to influence the quality of copper electrodeposits (Jenkins and Eamon, 1990).The influence of chloride and organic additives on copper electrodeposition has been the subject of considerable research. The addition of small quantities of chloride and organic additives has been recognized to significantly improve the properties of copper electrodeposits. These additives are critical in the prevention of dendrite growth and the production of smooth, dense cathode deposits.Chloride ions have been reported to catalyze the copper reduction reaction and assist in the production of uniform deposits (Lakshmanan et al., 1977; Sun and O’Keefe, 1992). Moreover, it is generally agreed that chloride ions depolarize the copper deposition process at low (several millimolar) chloride concentrations. This is because chloride ions catalyze the reduction of copper (II) ions to copper (I) ions (Cu2+ ? Cu+ + e-) in the rate-limiting step of this process (O’Keefe and Hurst, 1978; Ilgar and O’Keefe, 1997; Hebert, 2005; Shao, Pattanaik and Zangari, 2007)."

Jan 1, 2016

By César Beraun, Pablo Espinoza, Luis Loaiza

En la unidad Cerro de Pasco de Empresa Administradora Cerro SAC, existen varias fuentes de aguas ácidas de diversas características, con diferentes rangos de acidez y contenidos metálicos de hierro, zinc y cobre, que parcialmente han pasado de ser un pasivo, en términos económicos y ambientales, a ser una fuente de recursos. El tratamiento convencional que se aplicaba en la planta de neutralización consistía en neutralizar la acidez protónica y precipitar los metales disueltos utilizando lechada de cal y luego separar por sedimentación los sólidos formados para obtener un efluente tratado descargado por vertimiento y disposición de lodos formados en la relavera de la unidad. El cambio de pasivo a recurso para las aguas ácidas pasó por rehabilitar un proceso abandonado, identificando y separando en el interior de la mina subterránea un flujo que por su contenido de cobre ha sido separado en un circuito independiente del existente para las otras aguas ácidas de menores contenidos metálicos. Se desarrolló una secuencia de procesos de precipitación selectiva; inicialmente para recuperar cobre se implementó a escala industrial la cementación con chatarra de hierro. A escala piloto se han concluido tanto las pruebas para separar el hierro por oxidación y precipitación selectiva en medio ácido, como aquellas por las que, a partir de la solución pobre de la precipitación del hierro, se precipita el zinc en dos alternativas: precipitación alcalina como hidróxido de zinc o precipitación en medio ácido por sulfuración. A escala industrial, la recuperación de cobre en la cementación con chatarra de hierro alcanza el 75%, y 85% de contenido de cobre fino. A escala piloto, para el hierro se espera una recuperación sobre 95%, para un producto que alcanza 39% de fierro, mientras que para el zinc, la recuperación esperada es de 93% y un contenido de 35% de Zn en el precipitado de sulfuro.

Sep 20, 2019

By John R. Green

ROTARY kilns, varying in construction, are used in a variety of processes. Products differ and operating conditions vary according to economic requirements. All of these variables influence the degree of instrumentation and type of control necessary or profitable to install. Products fired in rotary kilns are the results of combined temperature and time treatment and the interrelation of these two factors should be kept constantly in mind in the perusal of this paper. MEASUREMENTS OF KILN TEMPERATURE The securing of proper temperatures within the rotary kiln, either of the charge or of the kiln lining in the high fire zone, are basic objectives of kiln operation; therefore the measurement of these high-temperature conditions merits first consideration.. For these measurements, radiation pyrometers, properly designed and protected, have proved adequate, particularly where records or automatic control are desired, while optical pyrometers may serve as portable indicators. Light-sensitive devices or photoelectric cells in this service are capable of producing records as well as certain forms of automatic control. High-temperature measuring devices for rotary-kiln work should have the measuring unit protected from dust, as a continued accumulation of deposit would lower the readings. Fig. I shows a typical application of radiation equipment to a rotary kiln, mounted far enough away from the sighting hole through the kiln hood to be protected from puffs or stingouts and with a sighting tube having a series of settling chambers, to prevent dust from reaching the lens. Although dust conditions inside the kiln itself usually fluctuate considerably and have their effect upon the readings at that moment, such effects are not cumulative and show as a continuous fluctuation in the temperature indicated, provided the radiation unit and recorder are responsive to such slight and rapid temperature fluctuations. The ambient temperature to which a measuring unit is subjected fluctuates from possibly o° to over 200°F., therefore these changes should have no effect upon the final reading or upon the life of the measuring unit. A very narrow sighting angle is desirable, so that measurement of temperature may be made as far as possible into the high fire zone without. effect of the flame temperature. There should be some sighting means on the measuring unit, so that the proper field may be viewed. Measurement of wall temperature taken at a point where the charge has just left the wall is less affected by dusting conditions than when taken elsewhere. Factors Influencing Temperature Table I gives an outline of the factors that produce kiln temperatures and com¬ments on the possibility of measurement and control. Of greater number and of varied influ¬ence are the factors that control when, where and how the heat is delivered to the kiln, the type of flame and the rate of

Jan 1, 1941

By J Williamson, M Griessmann

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Watershed tungsten deposit is located in the Hodgkinson Province of north Queensland, Australia. The deposit is hosted by Siluro-Devonian flysch-type meta-sediments of the Hodgkinson Formation, which were subjected to four major deformation events. Mineralisation has occurred syn- to post-D4 and is related to the intrusion of S-type granitoids of the Permian Whypalla Supersuite.Watershed is located within a regional NW–SE-striking melange zone composed of brecciated and intermixed arenites and shales. The major NW–SE-striking Tullah fault zone is situated in close proximity to the east of the deposit.The Watershed deposit occurs within a tightly folded upright anticline with NW-plunging fold axis. The anticline contains a major package of coarse-grained to conglomeratic arenite, which harbours the Watershed mineralisation. Several alteration styles occur within the arenites, of which Fe-poor calc-silicate alteration dominated by clinozoisite/epidote is the most significant. Less widespread but locally important alteration styles comprise garnet-dominated calc-silicate alteration, albitisation and sericitisation. The arenites are enveloped by unmineralised carbonaceous shales and shale breccias.Tungsten mineralisation occurs solely as molybdenum-poor scheelite and can be found as three styles: disseminated mineralisation in calc-silicate altered arenites, vein-style mineralisation with quartz-albite-scheelite veins and minor but high-grade mineralisation in albitised felsic dykes.Contact metamorphic rocks and geophysical data indicate the proximity of an underlying granitic body. It is believed that this granitic body was the main driver of the hydrothermal system generating the Watershed deposit. An early mineralisation stage caused the selective calc-silicate alteration of the arenites, while a second stage caused the vein-style high-grade mineralisation. The folded shales enveloping the arenites worked as an effective barrier that kept the mineralising fluids in a confined rock volume.The scheelite mineralisation at Watershed is open to depth, with a granite-hosted porphyry or greisen-style mineralisation anticipated below the current resource.CITATION:Griessmann, M and Williamson, J, 2015. The calc-silicate-hosted Watershed tungsten deposit, far north Queensland, Australia , in Proceedings PACRIM 2015 Congress, pp 545–550 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Alireza Javadi Nooshabadi, Kota Hanumantha Rao

Formation of hydrogen peroxide (H2O2), an oxidizing agent stronger than oxygen, by sulphide minerals during grinding was examined. It was found that pyrite (FeS2), chalcopyrite (CuFeS2), sphalerite ((Zn, Fe) S), and galena (PbS) generated H2O2 in pulp liquid during wet grinding and also when the freshly ground solids are placed in water immediately after dry grinding. Pyrite produced more H2O2 than other minerals and the order of H2O2 production by the minerals was found to be pyrite > chalcopyrite > sphalerite > galena. The pH of the water influenced the extent of hydrogen peroxide formation with greater amounts of H2O2 produced at highly acidic pH. Furthermore, the effect of mixed sulphide minerals, i.e., pyrite-chalcopyrite, pyrite-galena, chalcopyrite-galena and sphalerite-pyrite, sphalerite-chalcopyrite and sphalerite-galena on the formation of H2O2 showed increasing H2O2 formation with increasing pyrite fraction. There is clear correlation of the amount of H2O2 production with the rest potential of the sulphide minerals; the greater the rest potential of a mineral the greater the formation of H2O2. This study highlights the necessity of revisiting the electrochemical and/or galvanic interactions between sulphide minerals, and interaction mechanisms between pyrite and other sulphide minerals in terms of their flotation behavior in the context of inevitable H2O2 existence in the pulp liquid.

Jan 1, 2014

By C. M. Clapperton, K. E. Darke, A. J. Boyce, C. M. Rice, S. D. Redwood

"The Kori Kollo gold deposit is hosted by a c.15 Ma sericitized dacite stock in the LaJoya district on the Bolivian Altiplano. The mineralization is of the Bolivian polymetallic vein(BPV) type, with a signi?cant amount of the gold reserves contained in the oxide cap.Field and microscopic studies, K-Ar dating, ??34S values of pyrite, alunite and jarosite, and ??18O values of alunite and jarosite demonstrate that some of this gold is supergene. Two types of supergene gold are present: minute gold grains, 1 to 10 microns across, of high fineness and associated with jarosite and iron oxy-hydroxides; and ‘invisible’ gold, which is probably sorbed onto minerals such as jarosite and iron oxy-hydroxides.Pyrite ??34S values fall in the limited range -3.5 ± 0.6‰, consistent with a magmatic origin. Sulfate ??34S values are homogeneous and overlap closely with those of pyrite (-1.2 ± 2.1‰), which supports petrographic evidence that sulfates replaced pyrite. By contrast, sulfate ??18O values are inhomogeneous with a large range (alunite +2 to 26‰, jarosite -5 to +18‰). These data are interpreted as reflecting kinetically controlled reactions involving various proportions of atmospheric oxygen and local meteoric water. This is typical of supergene alteration and is due to the seasonally dry climate of the Altiplano.The oxide-zone mineralogy is dominated by sulfates and iron oxy-hydroxide minerals with some phosphates and halides, which indicates that the groundwaters were acidic, oxidizing and relatively saline. Under these conditions the most likely complexes responsible for gold mobilization are halides.Geological data and K-Ar ages indicate that oxidation of the BPV deposits began at least around 11 Ma and possibly up to 15 Ma ago, and that supergene alteration lasted until around 4 Ma. During this period, erosion was minimal. Although supergene processes have been active on the Bolivian Altiplano since the Middle Miocene, in contrast to Northern Chile, enrichment of gold has not occurred."

Jan 1, 1997

By James P. Bennett

The U.S. Bureau of Mines investigated the role of imported natural flake graphites in dolomite-carbon refractories used in steelmaking processes and evaluated carbon fibers as a potential substitute. Varying quantities (1.5-30 pct) of natural flake graphite and carbon fibers were added to test samples. The effect of the additions on modulus of rupture (75°-2,750° F), deformation under load (2,750° F), and air-slag-metal resistance (3,000° F) was studied. Carbon purity of natural flake graphite additions did not influence hot strength, deformation under load, or air-slag-metal resistance. When the quantity of 90-pct-carbon graphite addition varied between o and 30 wt pct, hot strength was highest, deformation under load lowest, and air-slag-metal wear the least at 10 wt pct. As test temperature increased from 500° to 2,750° F, the hot strength difference became less. Carbon fiber additions were limited to 1.5 pct in dolomite-carbon brick. At this level, physical properties were generally comparable to those obtained with natural flake graphite, but were below values obtained with 10-pet-f1ake graphite additions. Carbon fibers are not considered a satisfactory substitute for natural flake graphite.

Jan 1, 1989

Reliable and discriminating small, laboratory scale methods of study have been developed and used successfully in the critical evaluation and interpretation of the carbonization characteristics of a wide range of raw and prepared materials, the variable factors in the coking process, and' the mechanical properties of the carbonized products. The simple and highly economic technologies have been successfully and effectively integrated with detailed surface and subsurface geological exploration programmes (particularly in the coalfields of the .Central Bowen Basin of Queensland) as well as with quality and utilization studies of a nUII!ber of representative Australian and Japanese coals. Previously, only the results of comparatively large, laboratory scale studies have provided information reasonably indicative of those to be anticipated hi industrial practice, but these suffer serious disadvantages in terms of economy of material, time and resources; they have been difficult or even impossible to use as an essential part of any normal or comprehensive exploration programme. On the other hand, although previously developed smaller scale laboratory methods derive considerable advantage from their flexibility, amenity to critical control and inherent potential for speed and economy, they have hitherto permitted no effective or direct comparison with the results of industrial practice or full scale assessment. Comprehensive study results achieved through technologies developed recently at the University 'of Sydney demonstrate that carefully controlled small laboratory scale methods of evaluation quite suitable for use in exploration and, other programmes may be used to predict with considerable accuracy and reliability (in some cases exceedingthat of pilot scale study) the principal strength index of one of the established and internationally recognized full sc:ale tests-the Japanese Industrial-Standard Drum Test. It is probable that further study may establish satisfactory correlations with the results of other standard industrial procedures.

Jan 1, 1969

By C. M. Clapperton, K. E. Darke, A. J. Boyce, C. M. Rice, S. D. Redwood

"Abstract - The Kori Kollo gold deposit is hosted by a c.15 Ma sericitized dacite stock in the La Joya district on the Bolivian Altiplano. The mineralization is of the Bolivian polymetallic vein (BPV) type, with a significant amount of the gold reserves contained in the oxide cap. Field and microscopic studies, K-Ar dating, ??34S values of pyrite, alunite and jarosite, and ??18O values of alunite and jarosite demonstrate that some of this gold is supergene. Two types of supergene gold are present: minute gold grains, 1 to 10 microns across, of high fineness and associated with jarosite and iron oxy-hydroxides; and ‘invisible’ gold, which is probably sorbed onto minerals such as jarosite and iron oxy-hydroxides.Pyrite ??34S values fall in the limited range -3.5 ± 0.6‰, consistent with a magmatic origin. Sulfate ??34S values are homogeneous and overlap closely with those of pyrite (-1.2 ± 2.1‰), which supports petrographic evidence that sulfates replaced pyrite. By contrast, sulfate ??18O values are inhomogeneous with a large range (alunite +2 to 26‰, jarosite -5 to +18‰). These data are interpreted as reflecting kinetically controlled reactions involving various proportions of atmospheric oxygen and local meteoric water. This is typical of supergene alteration and is due to the seasonally dry climate of the Altiplano.The oxide-zone mineralogy is dominated by sulfates and iron oxy-hydroxide minerals with some phosphates and halides, which indicates that the groundwaters were acidic, oxidizing and relatively saline. Under these conditions the most likely complexes responsible for gold mobilization are halides.Geological data and K-Ar ages indicate that oxidation of the BPV deposits began at least around 11 Ma and possibly up to 15 Ma ago, and that supergene alteration lasted until around 4 Ma. During this period, erosion was minimal. Although supergene processes have been active on the Bolivian Altiplano since the Middle Miocene, in contrast to Northern Chile, enrichment of gold has not occurred."

Jan 1, 1997

By C. S. Spirakis, A. V. Heyl

Paper presented at the conference Economic geology in Europe and beyond II, models for mineral deposits in sedimentary basins, held in Keyworth, UK, 13-14 April 1994. The modified basinal brines, containing partly oxidised sulphur species, scavenged metals from basement rocks and sediments and transported them through the host rock, which contained local concentrations of organic matter. Reacting in various ways with the mineralising solution as temperatures at the sites of mineralisation changed, organic matter caused the precipitation and dissolution of a variety of minerals in the ore zones; it was organic matter that caused all of these reactions to occur at the same sites. Thus all components of the mineralising fluid - salt, water, heat, sulphur and metals - were obtained within the ore district. The siting of the mineral districts was related to the locations of faults through U- and Th-enriched granites beneath sediments containing basinal brines, and the locations of ore deposits within the districts were controlled by local concentrations of organic matter

Apr 1, 1995

By w. w. Milde

"Since its startup in 1975, the Rabbit Lake mill has been modified (0 process both increased tonnage and higher grade ore. Ore initially came from the Rabbit Lake pit . In 1985, a major mill expansion was commissioned to allow treatment of B-zone pit ore, which is mineralogically and metallurgically different fromRabbit Lake pit ore.Mill modifications, and the changing ore characteristics and processing targets which made them necessary, are described. Mill LocationThe mill complex, shown in Figure I, comprised of milling facilities, acid plant, power generation , warehouse and administration offices, is located approximately 1.5 Ian south of the Rabbit Lake pit, and about 8 Ian southwest of the B-zone open pit mine.Original Milling CircuitOre feed to the mill commenced June 10, 1975. The mill was designed to process 1500 tonnes per day , 483 000 tonnes per year with an average grade of O.44OJo Ups and an annual production of 2000 tonnes UPs' Run-of-mine ore was dumped directly onto a 60 em square opening grizzly. Oversize was broken with an Ingersoll-Rand hydrauli c rock breaker. Minus 60 cm ore was fed to a 6 m diameter by 1.8 m long Hardinge semi-autogenous (SAG) grate discharge mill. Mill discharge was screened over a Tyler double-deck vibrating screen, with screen oversize returned to the SAG mill feed chute via conveyor belt. Screen undersize (minus 2.4 mm) was pumped to 51 cm diameter Krebs cyclones in closed circuit with the SAG mill. Cyclone overflow (about 50% minus 74 micron) was thickened to 55% solids in a 30 m diameter neutral thickener .Thickened pulp was stored in two mechanically-agitated wood stave tanks (5.5 m diameter by 6 m high), to which sulphuric acid was added to obtain a pH range of 1.5 to 2.0. The fmalleaching was carried out in five more identical tanks. Sulphuric acid and sodium chlorate were used to maintain a pH of 1.5 and a terminal emf of -450 to -500 mV. Steam sparge was utilized to obtain a temperature of 45°C."

Jan 1, 1989

By T. B. Acton

There are two types of ore transportation systems in use at Newmont's Magma Copper Co. San Manuel mine in Arizona-rail-mounted, box-type rotary cars and the newer rail-mounted, bottom-dumping ASEA cars. Though the cost per car for the ASEA units greatly exceeds the cost per rotary car, the advantages of the ASEA units, including much faster dump times, have made the ASEA system a successful alternative at the San Manuel mine. The rotary system of ore transportation has been in use at San Manuel since production began in 1956. The system employs 7.9-m3 box-type cars to transport ore by rail to shaft pocket areas. A rotating dumping mechanism turns three cars at a time upside down to empty them, and returns them to an upright position. Trains of 15 cars each are dumped in about six minutes. Each 15-car train is pulled by an 18-t rated trolley locomotive. There are about 400 rotary cars in service at San Manuel and the system is used for the majority of ore haulage. This well-proven rotary method was instrumental in achieving the December 1977 world record of 272 Mt hoisted from an underground copper mine. Magma Copper Co. began using ASEA cars in late 1977. Designed by ASEA of Sweden, the cars are built for San Manuel by Kasper-Hall Manufacturing Co. in Tucson. The cars basic design feature is a hinged floor that opens at the side as the car is pulled through the dump. As it passes over the dump, a fifth wheel attached to the hinged floor (opposite the hinges) travels along a rail in the dump. This rail dips down into the pocket and then returns to track level. As the fifth wheel travels along the rail, the car floor opens, the car dumps, and the floor is then returned to track level. As the car is dumping, the body remains suspended over the pocket by wheel rollers attached to each side of the dump. Trains of 10 cars each are emptied in about 45-50 seconds. Each ASEA train is pulled by an 18-t rated trolley locomotive, adapted at San Manuel to allow it to pass through the ASEA dump. At minimal cost, "wings" are welded to each side of the locomotive. These wings suspend the locomotive over the pocket as the train passes through the dump. Advantages of the ASEA System Major design characteristics of the ASEA and rotary systems are shown in the accompanying table. The comparison points out some of the following advantages demonstrated by the ASEA system. • Faster dumping-An ASEA train dumps in 50 seconds, while a rotary train takes at least six minutes. There is no stopping or starting when dumping an ASEA train. The train enters the dump area, dumps, and leaves in one continuous motion-in contrast to rotary trains which must stop and start five times to dump. With the rotary system, three cars are spotted in the dump mechanism by remote control. When the cars are in place, the train operator activates the dump, the cars are turned over, and then returned to an upright position. This process is repeated until all 15 cars in the train are emptied.

Jan 4, 1980

By M. Leslar

Slope monitoring has been an important issue in static terrestrial lidar for some time. Several solutions for monitoring the progress of a slide have been devised over the years. All of these solutions have required users to be in the field operating the lidar equipment. This paper presents a new system developed using the Optech ILRIS-HD or ILRIS-LR lidar and the scripting language of PolyWorks to produce an autonomous slope monitoring system. This system has proven invaluable in detecting and alerting mine workers to potential danger within their mine sites. It has already been deployed in two mine sites and is scheduled to be installed at a third.

Feb 27, 2013

THE present article makes no claim to be exhaustive, since it cannot contain all the knowledge which scientists and manufacturers of the compounds of the rare earths have gained. The following notes are, therefore, simply an attempt to ascertain andclearly record the occurrence, properties, and uses of the more important of the rare earths, with a special reference to their commercial values and the industries based upon them.HISTORYIt was the mine manager, Gcyer, of Stockholm, who, in 1788, first drew attention to a black mineral which had been found in a quarry near Roslagen, in Sweden. In 1805 Klapproth received some specimens of this mineral, which he declared to be a newmineral. Subsequently Gadolin, professor of chemistry at Abo, analyzed the same mineral, and determined the presence of an unknown earth resembling alumina and lime. He named the mineral ytterbite, and afterwards gadolinite. Klapproth has alsothe merit of having detected (1804) another rare earth, which he named ochroit-earth, found in the Bastnas mine, near Riddarhyttan, in Wcstmannland, Sweden. Curiously enough, Hisinger and Berzelius simultaneously ascertained the existence of the same...

Jan 1, 1909

Coking coals are very much in demand on a world wide basis, particularly the higher rank coking coals, which form an important part of many coking blends and which represent the smallest portion of the world'scoking coal reserves. Conventional coke oven plants, using these coals, will predominate at least until the next century.Blending schemes for conventional coking require definition of the basic properties of coals so that the factors influencing the carbonization behaviour may be assessed. Several concepts, which are relatively simple, ate available to help promote a better understanding of the bask factors controlling -coke strength and are also useful in suggesting possible lines to follow in the blending of coals for coking.The interpretation of carbonization behaviour and coke structure in terms of petrographically defined coal rank and type provide a basis for planning and exploitation of coal Teserves. The optimum parameters for coking are suggested as follows.1. Type- Vitrinite content (% m.m.f. by volume) 55 ± 5%2. Rank- Mean maximum reflectance of vitrinite 1.30 ± O.10% Carbon content of vitrinite (% d.m.m.f.) 87·5 ± 1·0%The value of a coal should be assessed in relation to all its possible uses in blends. This is a more realistic and productive approach, as compared with considering coals only in relation to the results of blending with"good" coking coals. Blending schemes have been outlined to assist in the assessment of the blend potential of coals of all ranks and types.Reserves of higher rank coking coals in N.S.W. are very limited and should be conserved by blending with the low rank coking coals, of which there are large reserves.Examination of blending theories in relation to N.S.W. coals suggest that blends in the broad categories of minimal downgrading of the higher rank N.S.W. cok...

Jan 1, 1972

By William P. Blake

We are so familiar with water in its liquid and its solid form, that we seldom think of it as a mineral, and still less as a mineral product of any considerable industrial importance, though in the form of ice it is mined and stored up in enormous quantities yearly. The industry is peculiarly American, and in no other country has the business of cutting and storing ice been so well systematized and perfected. The interest has grown steadily from year to year, until it has attained large proportions, the annual production being counted in millions of tons, requiring, in the aggregate, a large investment of capital in all the Northern States. It gives employment, also, to thousands of men and horses, in the depth of winter, when farming work cannot be carried on. Ice is not only a luxury, but a necessity, in our climate, and is indispensable in many manufacturing operations: and finds constantly increasing applications and uses. As the industry has grown, so the necessity for suitable implements and tools has grown with it, and it has become necessary to systematize and cheapen the methods of handling such a large amount of material with rapidity and economy. As the industry is properly a branch of mining, and as our mining literature does not, to my knowledge, contain any description of the methods and appliances used in it, it seems desirable to place a brief description on record in our Transactions, and I therefore offer to the Institute the following outline description, based partly upon observations for several years past of the methods and processes employed, and partly upon the information obtained from prominent ice-miners and from the manufacturers of ice-tools. My acknowledgments are particularly due to the firm of W. T. Wood & Co., of Arlington, Massachusetts, for much information in detail, and also to the Knickerbocker Ice Company, of Philadelphia. The wood-cut blocks used in the illustration of this paper, have been kindly lent by both of these firms. The sequence of operations in getting ice is as follows : 1. Wetting down a light snow. 2. Scraping off an excess of snow, if present. 3. Marking out the field. 4. Ploughing and cross-ploughing. 5. Cutting the channel and detaching large floes.

Jan 1, 1883

By NILAMADHABA SAHU, Gajanan U. Kapure, Pankaj Kumar, Sunil Kumar Tripathy

Chromite ore processing tailings and low-grade manganese ores are typically considered waste due to their limited or negligible utility, leading to environmental and storage concerns. Researchers globally have explored various methods to utilize or upgrade these wastes, particularly because dumping chromite ore has been linked to severe health issues through Cr(VI) leaching. Individually, these ores lack economic value, and there has not been research on simultaneously reducing both low-grade ores. In this study, the focus lies on smelting these ores together, aiming to create a precursor alloy for 200 series stainless steel scrap. Initial research indicated the potential for scrap formation, validated through lab experiments with varying coke rate, basicity, and holding time. The investigation discovered that smelting this combination could yield a metal product comprising 59% Fe, 24.93% Cr, 7.56% Mn, 0.62% Ni, and 0.93% Si. The optimum basicity was found to be 0.6 with 80% recovery. Notably, this process eliminates intermediate steps in 200 series stainless steel production, potentially reducing overall CO2 emissions. This proposed method represents a cleaner, sustainable approach to repurpose these two waste ores, projecting a net profit of USD 330 per ton.

Jan 10, 2024