Search Documents

By H. Tudeshki, A. Tayebi

"The large extent of global production and consumption of aggregates from quarries, grabs one´s attention and makes its substantial and essential standpoint in the world today pretty clear. A great amount of aggregates is utilized in civil engineering applications such as road construction, railway industry, concrete production, etc. Considering this fact that igneous rocks display a higher strength and abrasion resistance, this type of rock is preferred in the field of civil engineering. For all these applications, rock quality assurance is a key factor and certainly unavoidable, and it has great influence on the quality of constructions in civil engineering. One of the major problems encountered by both the producers and users of igneous rock is the fact that, with the passage of time, some specific rocks lose their strength, up to a complete loss of structure or in other words, their disintegration and degradation. In the last decades, different methods and procedures such as Glycol test, methylene blue dye test, as well as the Los Angeles test have been introduced to distinguish these rock properties, and to identify these problems. However, as these methods are time consuming, hard to perform, only to be applied to hand-piece samples, requiring special laboratory equipments, and only possible to be accomplished under laboratory conditions, their application has always been limited to some specific cases, and they are neither recommendable nor advantageous. In addition, these methods provide partially different results for the same rock. To address this widespread quality management problem of the quarry industry, a relatively quick, easy and user-friendly approach is necessary. It calls for a systematic solution with a device that can simply be used day to day in a mine for quality control of the quarry´s daily production. This scientific research is concentrated on developing a systematic method for early recognition and diagnosis of rock quality, in order to control and manage the quality of the quarry production in advance. This method was developed, based on the procedure of the magnetic susceptibility measurement. The obtained values can lead to valuable information regarding the quality of the rock and allows the quality control process to be accomplished and performed at the borehole location. This approach has been assessed through extensive field and laboratory studies. A detailed and comprehensive discussion will be made on the results of the experiments. The advantages and impacts of the application of this method, on increasing the reserves and environmental protection are also discussed."

Jan 1, 2011

By E. R. Weltevreden, C. Klauber, C. Vernon

"In this paper a review of the current status in recycling technologies for cathode ray tubes is given for both the glass and phosphors. Particular emphasis is placed on the opportunities for the recovery of the rare earth elements (REE) from the phosphor coatings. This is placed in the market context of alternative virgin sources and some of the advantages and disadvantages for REE waste recovery. Future opportunities are explored and also some experimental detail on a low cost leach system is presented. INTRODUCTIONThe disposal of cathode ray tube (CRT) based colour televisions has accelerated world-wide with the development of high definition flat screen panels. The total number of colour CRT televisions that have been sold in the United States in the mid-20th century is estimated to have been over 2 billion (U.S. Environmental Protection Agency, 2007), with high current rates of disposal. It is estimated that of the 20 million televisions annually discarded, 78% are send to landfill (Nnorom, Osibanjo & Ogwuegbu, 2011). However, this easily accessible item of electronics cannot only be turned into a valuable resource using the right recovery procedures, it can also prevent the substantial environmental contamination arising from improper disposal. In this review we focus on previous and current work performed on the recycling of CRT based televisions. Due to the increasing demand for rare earth metals, the main focus will be on the possibilities and challenges of recycling the fluorescent phosphor powders on the CRT’s panel glass.CATHODE RAY TUBE’S GLASS RECYCLINGConventional cathode ray tubes consist of three main parts, the panel, the funnel and the neck (Figure 1). To produce the different colours on the screen, the inside of the panel is coated with a matrix of hundreds of thousands of small phosphor dots. Each dot is one of three types of coloured phosphors, emitting either red, green or blue light. These emit light when excited by a beam of electrons generated by electron guns located in the neck of the CRT. These beams pass through holes in the shadow mask and excite the phosphor coating on the inside of the panel, to give light of variable RGB composition, see Figure 1."

Jan 1, 2012

By A. S. Murphy, E. V. Manlapig, C. Green, J. W. Parkinson

Historically in Australia and the United States many coal mines deposited raw wash plant fines into large slurry impoundments. At the time the technology and market economics did not exist to make it viable to recover coal from these tailings. Today better technology exist to dredge and clean the tailings and there are circumstances where government regulations and market forces have come together to make coal recovery from these old tailings impoundments economically viable. This paper discusses the processes and equipment being used in tailings impoundment reclamation operations in Australia and the United States, and discusses the economic forces driving these operations.

Jan 1, 2001

By Yves Dardel

THE literature concerning the remelting of aluminum and its alloys is very rich. Unfortunately the greater part of the papers about this subject have no scientific value, for the theories or explanations are too often in opposition to the laws of physical chemistry. Furthermore only a few of the methods of purification1,2 are considered in the literature. Hence it has seemed necessary to the author to sketch a general theory of the purification of secondary aluminum. The purpose of the purification is to eliminate the impurities that the charges and the atmosphere of the furnaces bring into the bath during the successive remeltings. Indeed scrap as well as metal can be used when soiled with oil, greases, water, .. , if it has been sufficiently dried and contains oxides. At the melting point of the metal, the oils and greases are decomposed into their constituent elements H2, 02, H2O, C02, CO, CH4, and others. These gases are added to the corresponding gases in the atmosphere of the furnace. The impurities introduced into the metal during the remelting will accordingly be the products resulting from the action of these gases on the liquid bath. The quantity of hydrogen that is soluble in aluminum and its alloys is given by the relation of Sieverts3 as a function of its partial pressure PH2 in the atmosphere [m = K _%/PH, [I]] where K is a constant, which depends only upon the temperature and increases with it. The experiments of Röntgen and Braun4, Röntgen and Möller5, Bircumshaw6 and Winterhager7 have rendered it possible to determine the value of K, when the temperature is inferior to 1.000°K. One obtains: [log K = - 4,702.5 + 0.238 [2]] Besides its usual signification, the term PH2 represents also the internal pressure of dissolved hydrogen, since in the equilibrium, that is, when no gas exchange occurs between the two phases, the pressures of hydrogen in the metal and in the atmosphere must be equal. Eq I shows that when the partial pressure of H2 increases the amount of dissolved hydrogen in equilibrium increases, and that, if the contrary occurs, the quantity of H2 should diminish. However, if for any reason the diffusion of hydrogen is hindered and the total amount of dissolved gas remains constant while the temperature lowers, the internal pressure of H2 increases until it reaches the value of the hydrostatic pressure. At this point, bubbles of hydrogen appear in the bath and escape out of it. The amount of hydrogen in the metal is then limited by a maximum depending on the hydrostatic pressure, which is practically equal to one atmosphere. Indeed hydrogen does not accumulate in the form of a hydride appearing as a separate solid phase. However, even the mechanism of the solubility is not yet elucidated. One does not know exactly as yet, whether the

Jan 1, 1947

By Luciano França Rocha

A medição online de umidade de finos de minério de ferro sempre foi uma informação muito desejada nas plantas de pelotização de minério de ferro. Controlar a umidade do pellet feed produzido pela unidade de filtragem além de possibilitar maximizar a produção deste setor da planta garante uma maior estabilidade no processo de pelotamento e de endurecimento. Para conseguir entregar esta medição à sala de controle, iniciamos um projeto utilizando a metodologia Design For Six Sigma para desenvolver uma forma de medição desta grandeza. Inicialmente foi feita uma revisão bibliográfica sobre o assunto. Posteriormente, foram realizadas visitas técnicas que eliminaram algumas possíveis tecnologias de medição. Finalmente, foram avaliadas as tecnologias de Absorção de RF e medição por um braço robótico para serem avaliadas. O primeiro teste industrial foi realizado com um medidor de absorção de RF que não apresentou bons resultados. A faixa de interesse de medição é muito estreita (9% a 11% de umidade). Esse fato exige uma boa precisão do equipamento para que a medida tomada do processo seja útil e sua incerteza não ocupe toda a faixa. Como nenhuma das tecnologias de medição online existentes no mercado se mostrou precisa suficiente para a aplicação, a alternativa foi utilizar um braço robótico para coletar, secar e medir a umidade através do método tradicional feito por um robô. Esta última alternativa se mostrou robusta e adequada ao controle de processo da unidade de filtragem, produzindo resultados confiáveis e precisos.

Jul 30, 2018

The association of deep well turbine type pumps with metal mining is by no means a new one, though undoubtedly each application has certain features of interest, conformable with attendant circumstances. Although all conditions pertaining to a particular operation in one mine are rarely, if ever, duplicated in another mine, it is felt that some aspects will be parallel, or in various ways comparable.Therefore the following descriptions of an installation of a deep well turbine pump as part of dewatering plant in connection with shaft sinking may be of general interest to metal mine operators.The Man and Supply shaft at Mount Isa Mines is designed as shown in plan by Fig. 1. It is the main entrance and service shaft for the entire property and hence is in constant use. Arrangements for sinking must be such as to cause little or no impediment to routinehoisting work. Also, being the main shaft, it has been essential to deepen it in step with successive level developments.During the period of operations at Mount Isa only a limited time has been available to complete succeeding levels down to the present No. 7 haulage level (895 ft.), and sinking operations in soft, broken, leached, and heavy water-bearing country have presented many features militating against reasonable speed and cost. Outstanding among these difficulties has been the large volume of water contained in the pervious brecciated country.

Jan 1, 1939

By P J. White, J V. Lawless

Low-sulphidation epithermal gold deposits, which form in quasi-hydrostatic convective hydrothermal systems, frequently contain chalcedony within high-grade ore, which has been interpreted to be a crystallisation product of amorphous silica. To deposit amorphous silica rather than another silica polymorph at elevated temperatures requires very high silica concentrations, because of its relatively high solubility. Only extreme boiling caused by decompression followed by wall rock heating upon structural dilation, can achieve this. As gold deposits with amorphous silica it must be produced by the same mechanism, particularly since extreme boiling is also a very effective mechanism for gold deposition. Recent developments support this view; the first is the detailed isotopic analysis of chalcedony-bearing high-grade veins reported from Hishikari, Japan, in which oxygen isotope results are indicative of extreme boiling and hydrogen isotopes indicate initial deposition of amorphous silica. The second is the finding of chalcedony within geothermal pipe work in the Rotokawa geothermal field in New Zealand. Rotokawa is a comparatively hot field (335¦C at depth); hence separation of the steam-water mixture produced by the wells is undertaken at a comparatively high temperature (220¦C) to minimise down-stream silica scaling. Even so, silica scale, some of which is chalcedony, does occur, under similar conditions to that in low-sulphidation epithermal deposits. Evidence of chalcedony forming under these conditions, reinforces the interpretation that decompressive boiling is the main deposition mechanism for gold in low-sulphidation epithermal deposits. It is possible that there is sufficient drop in temperature due to decompression that, at least initially, the silica deposits directly as chalcedony. Low-sulphidation epithermal gold deposits that do not contain chalcedony, such as those in the Philippines, may form at temperatures too high for chalcedony to directly form. The recognition of decompressive boiling as the main deposition mechanism in low-sulphidation epithermal deposits means that exploration can focus on zones where this has taken place by combining paleohydrological reconstruction and structural geology.

Jan 1, 2002

An efficient and portable mathematical model has been developed for simulating heat transfer in six-in-line slag-resistance-heating electric furnaces for smelting sulphide ores to produce base metals and platinum group metals. This model is a steady-state one relating furnace conditions and performances to various control and input parameters. Some transient effects occurring in electric furnaces are neglected for computation efficiency. This article describes the model development and modelling results. The present model is capable of predicting: (i) temperatures at various locations in a six-in-line furnace, such as slag bath, matte bath, solid charge, freeboard space, freeze lining, cooling water, and air gaps between solid material components, etc. (ii) freeze lining thickness, (iii)smelting rate, and (iv) heat loss rate, etc. A typical feature of the model is that it is easily portable to different application platforms and sufficiently efficient with execution times less than a few seconds. Therefore, it is possible to apply the model for online prediction and control of heat transfer and freeze lining thickness in industrial electric furnaces.

Jan 1, 2011

By Henry Kreisinger, WALTER T. RAY

This bulletin contains a statement of certain results that will be embodied in a report describing investigations of the combustion of fuel made by the United States Geological Survey and the Bureau of Mines in a specially constructed long furnace. The furnace forms part of the fuel-testing plant at Pittsburg, Pa., which was established and equipped by t.he Geological Survey, but passed under the control of the Bureau of Mines on July 1, 1910, when a t.ransfer of fuel-test.ing investjgations, authorized by act of Congress, became effective. The work discussed in this bulletin was done under the direction of the Geological Survey. The furnace was designed and built for an experimental study of the processes of combustiop, this study being part of a comprehensive plan for testing fuels to determine their heat value and the manner in which they can be used to best advantage. Although the main object of the researches made with the furnace by the Geological Survey was to examine critically the production of sensible heat by combustion along the path of the gases rising from the fuel, an interesting as well as important side problem developed in the study of the simultaneous dissipation of the heat through the walls and roof . of the furnace. Thus incidental data were collected on the temperature gradient through the walls at several places. These temperature data. (together with the heat conductivity of the material of the walls) formed the basis for calculating the heat dissipated through the walls. The object of this report is to present and discuss these temperature data. The discussion particularly concerns the air-space type of wall construction as compared with the solid brick wall or walls type, in which the air space is filled with some solid material of low heat conductivity. The conclusion of the authors, which perhaps will surprise some readers, is that, so far as loss of heat is concerned, a solid wall of brick or any ordinary material is preferable to a hollow wall of the same total thickness, especially if the air space in the hollow wall is near the furnace side. There is a general belief that l?ince air is a poor conductor of heat, air spaces built into the walls of a furnace will prevent or reduce heat dissipation through the wa.lls. Although there may be instances of furnace walls in which such construction reduces the rate of heat flow through them, yet as a rule the effect of the air space is just the opposite. While the heat does travel very slowly through the air by conduction, it leaps over the air space readily by radiation. Although this latter mode of heat propagation is common in nature, the laws governing it are not generall;y known and are seldom taken into consideration when furnace walls are being designed. It may be stated here that the quantity of heat passing through a. portion of a solid wall by conduction depends on the difference between the temperatures of the two planes limiting the portion of the wall. The quantity of heat that passes across the air space in the waH depends on the difference of the fourth powers of the absolute temperatUI: es of the surfaces inclosing Hie air space. It follows that, in case the heat. passes by conduction through the solid'portion of the wall, the loss remains approximately the same so long as the temperature of the two limiting planes remains constant, no matter what may be the temperature of the two planes. On the other hand, the heat passing across the air space by radiation increases rapidly with the temperatures of the inclosing surfaces, although the difference between these temperatures may remain constant. This feature will be shown by curves in the latter part of this paper and thoroughly discussed. The important point is that the air space, which is advantageous in the walls of a refrigerator because the temperatures are low, is objectionable in a furnace wall because the temperatures are high. It is customary to put air spaces in furnace walls between the firebrick linings and the common brick. Usually the fire-brick lining is only half a brick thick, which construction brings the air space too close to the furnace. The result is that the temperatures of the surfaces inclosing the air spaces are too high, and in consequence too much heat is radiated across the spaces. The heat passing through such walls would be much reduced if the air spaces were filled with brick, or, better, with some cheap nonconducting materials, such as ash, sand, mineral wool, etc. Even where the fire-brick lining is one brick thick (9 inches), the temperature in the furnace may be high enough to raise the temperatures of the air-space surfaces so much that the heat radiated across the space will amount to more than would the heat conducted through a filling, were the filling only common brick. This last statement is amply justified by the data here presented.

Jan 1, 1911

? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 1997

By W. M. Baldwin, C. R. Johns

Cobalt is reported1,2 to scale in accordance with the Pilling and Bed-worth3 parabolic law: where w = weight increase per unit surface area K = constant l = time The reported values of the parabolic oxidation constant, K, in the temperature range 600 to 1100°C follow an Arrhenius type of equation as inspection of Fig 1 shows. According to Valensi's theory5 on the scaling of metals where multiple-layered scales (for example, MeX, MeX2, and others) are possible, this fact could be construed as indicating that a single oxide only is formed on cobalt in this temperature range. Since the single straight line extends above 920°C where only CoO is stable in air (see Fig 2) it might be inferred that this is the only oxide formed on scaling. Arkharov and Voroshilova10 have studied the scales formed when cobalt is heated in air in the temperature range 385 to 800°C and report that CoO is indeed found in the scale but that CoO4 is also found as an overlay and in increasing amounts in the lower temperature ranges. No quantitative data regarding the relative proportions of the two oxides were reported. Again in the light of Valensi's theory this would indicate that the straight line in Fig 1 would be expected to undergo an inflection at some point in the temperature range 385 to 800°C. Chauvenet2 has studied the oxidation rates of CoO to Co3O4 and has found this reaction to proceed parabolically with time but reports parabolic scaling rates which are considerably (about ten times) larger than the scaling rates of cobalt metal itself. This is difficult to explain in terms of Valensi's theory although a full discussion of the possible discrepancy cannot be made in view of the lack of sufficient data. These points made an investigation of the scaling behavior of cobalt in air an attractive study. Discussion of Results Relatively large (approximately 95 sq cm of surface area) samples of 0.020 in. thick electrolytic cobalt strip,* sanded with 2/0 paper, were heated in air in a cyclone type furnace. The samples were weighed before and after the scaling treatment. The weight increases so observed obeyed the Pilling and Bedworth parabolic law at all temperatures studied. The parabolic scaling constants when plotted on a logarithmic scale as a function of absolute temperature are reproduced

Jan 1, 1950

The Ekati Diamond Mine is located on permafrost terrain in CanadaÆs Northwest Territories. The mine rock consists of: diamond-bearing and barren kimberlite; and surrounding waste rock such as granite. The kimberlite occurs in several vertical æpipesÆ that are, or will be, mined using open pits. Early predictions of drainage chemistry at Ekati identified the potential for ARD due to sulfide oxidation from both waste rock and kimberlite. This was surprising for the kimberlite, because neutralisation potentials (NP) are typically hundreds of kg CaCO3 equivalent/t. However, subsequent testwork showed that substantial portions of the NP ædisappearedÆ quickly, apparently due to the unusual non-carbonate mineralogy. In any case, additional predictive work concluded much of the rock was benign and there would be no ARD. Shortly after mining started, ARD appeared from both the waste rock and kimberlite, although a few years passed before the company and its consultants recognised that at least some of the acidic water was ARD. Numerous other processes have been put forward as possible explanations for the remaining acidic drainage, although none have been either confirmed or eliminated. Because: the causes of the ARD and acidity are not known; no causes have been eliminated and more have been added; drainage chemistry was not predicted accurately; and future mining will encounter similar rock. I believe the Ekati Diamond Mine needs high-level assistance to understand current chemistry and to avoid problems with future drainage. Organisations like INAP, MEND3, and universities could provide this assistance.

Jan 1, 2003

By Hudson S. B

With a particular electrode configuration, and a particular combination of electrode voltage and roll speed, a relatively small increase in electrode voltage, or a relatively small decrease in roll speed, resultsin a marked improvement in the separation of zircon from ilmenite. In general, fine minerals can be separated using a higher roll speed, or a lower electrode voltage, than is required to separate coarse minerals. The ionizing electrode should be reasonably close to the point at which mineral is fed on to the roll, and nearer to the roll than the non-ionizing electrode. The optimum conditions for the separation of zircon from ilmenite may not apply for the separation of other non-conductors from other conductors.INTRODUCTIONAlthough the high tension separators used in the Australian beach sand industry are efficient, this efficiency has been gained very largely by a process of trial and error, and not by a systematic study of the effects of changes in the operating variables. The optimum roll speed for a particular electrode position and electrode voltage, and the optimum electrode voltage for a particular roll speed and electrode position, can both be determined quite readily. It is not so simple to determine the optimum electrode position for a particular electrode voltage and roll speed. The reason for this is that the electrode used in high tension separators consists of two parts-an ionizing and a non-ionizing electrode respectively. The angular and radial positions of these electrodes, relative to the feed roll and to each other, affect the behaviour of conductors and non-conductors to varying degrees.

Jan 1, 1962

By S. S. Klima, D. E. Pollock, J. A. Organiscak

"Airborne respirable coal dust capture by water sprays or wet scrubbers has been studied and developed over many decades as an engineering control to reduce dust exposure in coal mines and combat coal worker pneumoconiosis. Empirical relationships and deterministic models for particular dust capture experiments have previously been devised to show the key parameters involved in airborne coal dust capture. Many of the results from these models show that the significant parameters related to airborne dust capture are water spray pressure, water quantity, water droplet size, relative water droplet-to-dust particle velocity, and total operating air pressure of the scrubber. However, many airborne dust capture efficiency relationships and models developed for particular experiments cannot be readily applied to forecast the dust collection efficiency of different spray and scrubber design configurations, which rely on several key dimensional engineering measures. This study examines engineering measures from previous water spray and wet scrubber experiments conducted by the U.S. National Institute for Occupational Safety and Health (NIOSH) and the U.S. Bureau of Mines (USBM) to develop empirical models for wet collection of airborne dusts. A dimensionless empirical model developed for predicting airborne dust capture efficiency of water sprays and wet scrubbers is presented. IntroductionWater sprays have been one of the earliest mainstay engineering controls used to suppress respirable dust in underground coal mines. Some of the earliest reports of water spray usage on continuous mining machines indicated respirable coal mine dust reductions of 20 to 60 percent (Kobrick, 1970). Not long after the enactment of the 1969 Coal Mine Health and Safety Act, the U.S. Bureau of Mines (USBM) and others conducted extensive research into water spray and wet scrubber systems to control respirable dust in coal mines. The primary aspects of water spray dust control included prewetting for dust prevention, localized ventilation redirection and airborne dust capture, which are summarized in handbooks or best-practices guides (Kost, Yingling and Mondics, 1981; Kissell, 2003; Colinet et al., 2010). Initially, underground studies were conducted to identify the primary sources of dust during the mining processes and effective dust controls (Courtney, Jayaraman and Behum, 1978; Jankowski and Organiscak, 1983). Laboratory research systematically studied ventilation and airborne dust capture effects of water sprays and scrubbers to improve their application in underground coal mines (Tomb, Emmerling and Kellner, 1972; Divers and Janosik, 1978, 1980; Grigal et al., 1982; Ruggieri et al., 1983; Jayaraman, Jankowski and Kissell, 1985; Volkwein, Ruggieri et al., 1985; Jayaraman, Schroeder and Kissell, 1986; Divers, Jankowski and Kelly, 1987; Jones and James, 1987)."

Jan 10, 2018

A subsurface study of the Maria Lode and associated hydrothermal alteration of andesites within the Karangahake epithermal gold-silver deposit defined the local evolutionary sequence in the once active geothermal system.   Some implications for mining of epithermal deposits arise as a result.

Jan 1, 1984

By Julian Malnic

Various natural, commercial, engineering and operational factors govern the evolution of approaches taken in the exploration for Seafloor Massive Sulphides (SMS) and in delineating the resource. These stages are prerequisites to the proposed mining of SMS deposits. This paper presents and analyses these factors from the view of an SMS exploration company that is pioneering the exploration of this rich alternative source of zinc, copper and gold. Current exploration practices developed by Marine Scientific Research (MSR) workers for SMS deposits are expected to give way to industry-generated methods as the SMS exploration industry gathers momentum. The exploration process falls into three phases that are described below: Prospecting (locating targets), Indicating Resources, and Measuring Mineral Resources Considerable streamlining of the SMS exploration process will accelerate the rate of discovery. The economics of SMS mining are projected to be superior to comparable terrestrial mining operations in both operating cash cost and capital terms.

Jan 1, 2001

Two small coral islands in the Pacific Ocean, situated close under the equator, and formerly classed among the Line Islands, have, during the last three or four years risen into prominence owing to the valuable deposits of phosphate of lime discovered on them.The deposits of Ocean and Pleasant Islands are under the control of the Pacific Islands Company (1902) Limited, of London and, Sydney, and the high grade of the phosphate, together with the exceptionally favourable facilities for mining this mineral, of which there are several millions of tons on these islands, give this company advantages which enable them to command the Australian and New Zealand markets, and also to make large contracts with Japan and other countries. Both islands, as far as surface indications are concerned, are entirely constructed of coral, with phosphate on the top from the highest points to the present sea level, there being no sign of volcanic rocks, with the exception of a few pieces of drift pumice on the coast.Banaba (Paanopa according to. the Admiralty charts), also known as Ocean Island, was discovered in 1804. It is situated in lat. 0° 52" S. and long. 169P 3[)" E.

Jan 1, 1904

The National Economic Viewpoint? Any substantial project undertaken by private enterprise would normally be subjected to a Discounted Cash Flow analysis of its commercial viability, and would proceed only if the rate of return was judged satisfactory. A 'national viewpoint' analysis attempts to do the same but from the viewpoint of the community as a whole. The objective is to ensure that those projects are undertaken which yield the best return, economic and social, to the nation as a whole.

Jan 1, 1984

By Maurice Bottiau

"Abstract When addressing the performance of deep foundations, many parameters play a role, from adequate soil investigation to performance monitoring and testing. The correct understanding of pile construction, though, remains crucial. After a long period of empirical design and regulations, the last decades have been the ones of theoretical considerations and extensive codes writing. The interaction between technology and design, however, still plays a determinant role. The introduction of hydraulics and the exponential increase in available power on one hand, the miniaturization and the introduction of electronics in control and monitoring systems on the other hand have exerted a major influence on new foundation systems or the evolution and control of existing systems. It appears important to try to take execution related parameters and their control during execution more deeply into account when assessing the final result of the deep foundations and the achieved level of safety and reliability. In this contribution, we will try to analyze how systems, equipment and pile production monitoring and testing can influence the pile performance, and if/how this influence could/should be translated in adapted safety or installation factors. This analysis will run through different categories of piles: driven, augercast and displacement auger piles and bored piles. INTRODUCTIONThe global performance of a deep foundation depends on different aspects (Poulos, 2003):1. Ground investigation2. Design and analysis3. Construction4. Testing5. Performance monitoring6. Remediation and performance enhancementThis paper intends to address the importance of pile construction and the control of it on the final performance of the pile-group of piles. There has been an increasing interest for theoretical analysis over the last 20 years, followed by an increasing impact of regulation and codes. Without denying the importance of the latter, the author wants to point out how installation procedure and project specific parameters can largely influence the reliability of the deep foundation. In this context, detailed and prescriptive standards can miss their objective of intended improvement of accuracy and reliability, but even worse they can adversely impact engineering judgment. In today’s construction world, it is possible to gather installation information which can be of outmost importance for the final deep foundations performance. Therefore, the increase or decrease of installation reliability through adequate pile testing and performance monitoring should be emphasized and should be taken into account in the codes. This is the case already in most advanced codes, but in a limited and insufficiently refined way. After reviewing how codes deal with this issue today, we will show some recent examples of unexpected results due to pile installation. We will try to put these examples into a broader perspective by highlighting some reference and/or recent literature considerations. Finally we will try to summarize how pile testing and installation documentation can increase reliability and attempt to open the debate on how codes could/should allow for more engineering judgment."

Jan 1, 2014

By Ana E. Bohé, Georgina De Micco, Gastón G. Fouga

"In this work the reaction between several manganese oxides and chlorine is investigated in the range of temperatures between 650 and 950ºC. The reaction path for the chlorination of MnO is established, which involves recrystallization of high valence manganese oxides (Mn3O4 and Mn2O3) followed by its chlorination. For this reason, to understand the reaction of MnO, the chlorination of Mn3O4 and Mn2O3 has also been studied. The starting temperature for the reaction of these oxides is determined by non isothermal thermogravimetric measurements. The effect of temperature is analyzed, under our experimental conditions the rate of reaction is mass transfer controlled. The activation energy for the volatilization of manganese chloride is obtained which is in good agreement with volatilization enthalpy of MnCl2.IntroductionMany oxide ores which have manganese in their composition undergo chlorination processes during the extraction of refractory metals such as Ti, Hf and Nb. Although several works related with chlorination of manganese oxides were reported, there is no information about the kinetics or mechanism of the manganese oxide chlorination reactions. Okahara et al. studied the chlorination of manganese oxides and established that they react easily above 250ºC. Furthermore, they observed that chlorination of high order oxides is more difficult when there is not a reducing agent [1]. Ivashentsev studied the chlorination of manganese oxides using Cl2(g), CO(g) + Cl2(g) and COCl2(g). He established that the reaction of MnO started at 130ºC with formation of MnCl2(s), he also observed recrystallization of manganese sexquioxide [2]. Finally, the chlorination of manganese nodules from the ocean was studied by Murthy and Reddy [3] with the aim of obtaining valuable metals such as Mn, Co, Ni and Cu. They studied the influence of several parameters like temperature, carbon percentage, particle size and chlorine flow rate in the extraction process."

Jan 1, 2008