Search Documents

At an early stage of the examination of most prospects, samples are taken; and the sample values obtained play an important part in determining the subsequent history of the prospect. It is, therefore, important that. eveJJy effort should be made to interpret asfully as possible the meaning of the observed results. In this connection, it is suggested that examination of the assay values of mine samples by simple statistical methods may bring to light information of considerable value, which might otherwise be missed.Although expert statisticians may derive more information from the available data, those who are, like the writer, less proficient mathematically, may also benefit by applying quite simple statistical methods. At least they will develop a useful habit of thought bywhich they become aware at all times that sampling results only provide estimates of the truth, but that an assessment of the precision of such results may be possible. The object of this paper is to provide some evidence of. the truth of these statements, by theuse of a few very elementary statistical calculations.General.The idea that any mine sample is subject to error from a variety of causes is a very familiar one. Doubt always exists with regard to the representativeness of a perfectly cut sample, and other errors may arise through imperfections of sample cutting, crushing, splitting and assaying. Some causes of error may give rise to "constant" errors, others may cause variable but one-sided "systematic" errors, and others again may bring about variable results without any tendency toward bias on the average. In statistical language, mine sample values are subject to errors which may have either assignable causes or chance causes. The former are those which can be isolated, or should be capable of isolation, while the latter are those remaining when all assignable causes have been removed. A single constant assignable cause brings about bias in all results, and one or more than one variable assignable cause brings about variation between individual results and perhaps an overall bias. The system of chance causes that would remain if all assignable causes were removed would cause variation between individual results but no overall bias. There is no sharp practical line of distinction between the two types of cause) of error; nor is it ever possible by any method of statistical analysis to be certain that there are no assign...

Jan 1, 1950

Standards And Laboratory Monitoring In Gold Assay Key Components Of Best Practice

Jan 1, 2005

By J. R. Piper

“Old Borate,” located in the Calico Mountains east of Barstow, California, lead domestic colemanite production from 1884 through 1907. Mineral exploration at “Old Borate” in the early 1980's, examined borate mineralization in Tertiary lacustrine strata. Surface sample and drill hole locations, geology and structure, were hand-drafted on paper maps. To re-evaluate this data, the information was digitized using Geographic Information Systems software. Digital Elevation Model based terrain modeling integrated surficial samples with drill hole data to locate favorable drilling targets. Structural relationships were used to identify hypothetical resources formed by the leaching of boron from surface exposures, redeposited at depth.

Jan 1, 2001

By G. H. Cady, L. C. McCabe, D. R. Mitchell

While running certain float-and-sink tests, unit coal calorific values were determined for gravity fractions of a series of Illinois coals from several districts in the southern part of the state. When these values were plotted against specific gravity what appear to be characteristic curves of somewhat different shape were obtained for each district represented. This in itself seems noteworthy. The shape of the curves seems to indicate that the lightest fraction of the coal, which inspection shows to be largely vitrain, suffers the least deterioration in storage. It was also observed that on dilution curves established with dry ash and B.t.u. values the fractions of 1.35, 1.40 and 1.50 sp. gr., which constitute the greater weight per cent of a given coal sample, fall more frequently on a straight dilution line than do the lighter or heavier fractions of the same sample. In most instances there is a marked steepening between the 1.35 and the fraction of lighter gravity. In general the curve increases in steepness between the fractions of 1.50 and 1.70 specific gravity. The variations in the unit coal-specific gravity curves as well as those observed in dilution curves which appear to be pertinent to this problem are: (I) variation in coal substance with change in specific gravity, (2) variation in kind and quantity of mineral matter with the specific gravity of the fraction, (3) factors of analytical procedure which tend to introduce error in analysis, particularly in high-ash and high-sulfur fractions. DISCUSSION (A. C. Callen presiding) E. Stansfield, ? Edmonton, A1ta.-—The necessity of avoiding oxidation in grinding and in drying should be emphasized. My assumptions as to pure coal coincide with t,he author's but most of my curves are nearly straight lines. The low sulfur content

Jan 1, 1934

Ore samples generally require preparation before analysis. Serious problems can occur with contamination degradation and particle size effects. Both grinding element contammation and sample cross contamination havebeen bound to be related to sample hardness and operator technique. For best results with minerals relevant to the steel industry, the use of Siebtechnik-type mills required a combination of careful planning, short grinding periods and intermediate sieving of the sample. The results may be extended to most mineral, rock, and refractory sample preparabons.

Jan 1, 1978

Electricity supply constraints in SA are increasingly challenging mines to operate more energy efficiently without reducing production output. Mining compressed air systems are well known to be operated inefficiently and are also a major power consumer. Two available and proven technologies can be applied on new and existing mines to replace or and optimise available compressed air facilities and achieve meaningful reductions in electrical power consumption; ? Hydro powered drilling and mining is significantly more energy efficient than compressed air and provides drilling rates that are twice as fast. ? Stope drilling systems using compressed-air or water drills allow further energy savings. The technologies are discussed and a broad strategy to selectively apply these them together is presented.

Jan 1, 2008

By John C. Stankus

To improve mine roof bolt performance, Jennmar Corporation commenced the design and development of a new roof control sys- tem. This new system designated "Insta'l Compression", not only improves safety, but is more cost efficient due to reduced amounts of resin needed per bolt installation. In this paper the research and development of this new system will be outlined. Much of the information presented will be actual test data from various underground operations in Alabama, Kentucky, and Pennsylvania. The development of this system will also cover the design of a new expansion shell, resin compression ring, anti- friction washer, and upgrading of material specifications.

Jan 1, 1990

By Antonio Raschillà

On the 2nd of June 2007 SELI S.p.A. started the excavation of Beles Tailrace Tunnel (Ethiopia). The new 8,07 m diameter DS Universal TBM utilized for the tunnel excavation was manufactured by SELI S.p.A. and allowed the installation of 30 cm thick concrete lining, contemporaneously with the excavation of 7,200 m of tunnel. The greatest part of the tunnel alignment was excavated in hard and sound basal-tic rocks. The paper describes the main steps of the tunnelling operations which led to a remarkably rapid excavation, with a peak production of 36 m / day and a final break-through achieved 46 days ahead of the contractual deadline. Furthermore the paper describes the work and logistic organization that was set up to efficiently perform the mechanized excavation in the very remote area of the project.

The amount of liquid retained in a porous bed is determined by weighing a column containing the bed.The column is attached to the free end of a cantilevered beam, and changes in weight are determined by calibrated strain gauges (which form a resistance bridge) attached near the fixed cnd of the beam. By coupling the output from the strain gauges to an amplifier and a recorder, a continuous record of changes in the drainage characteristics of the bed may be obtained.

Jan 1, 1968

By S. Kursunoglu

The aim of this study was to investigate the effectiveness of Ascorbic (C6H8O6) Acid (AA), Activated Carbon (AC) and Guar Meal (C6H12O6) (GM) as a reductant for the simultaneous complete dissolution of zinc (Zn) and manganese (Mn) from a spent and mixed Zinc-Carbon (Zn-C) and alkaline battery powders in sulphuric acid (H2SO4) leaching. AA was tested previously as a reductant by other researchers while AC and GM were tested as a reductant for the first time in battery recycling. The effects of H2SO4 concentration, AA/AC/GM dosages, reaction temperature and leaching time on the Zn and Mn dissolutions were investigated according to 2k full factorial experimental design and Central Composite Design (CCD) technique; then, a simple optimization study was carried out for comparing the reductants. The optimum reductive acid leaching conditions for AA were determined at 3 hours leaching time, 70°C leaching temperature, 0.5M H2SO4 concentration, 13 g/L AA dosage, 1/20 g/mL solid/liquid (S/L) ratio and 200 rpm stirring speed. Under these conditions, the dissolution efficiencies were 99.9% for Zn and 99.3% for Mn. The best reductive acid leaching conditions for AC were determined at 3h leaching time, 80oC leaching temperature, 1M H2SO4 concentration, 3 g/L AC dosage and 400 rpm mixing speed. Under above conditions, Zn and Mn dissolutions were not complete. At 2M H2SO4 concentration, 10 g GM dosage, 700C leaching temperature, 200 rpm stirring speed, 1/20 g/mL solid/liquid (S/L) ratio and 3 hours leaching time, full dissolution of both Zn and Mn was achieved. As a result, three different reductants were evaluated in this study for complete simultaneous Zn and Mn dissolutions. This paper also compared present test results with previous spent battery recycling studies for Zn and Mn dissolutions. Full valuable metals dissolutions from spent batteries were achieved at low H2SO4 concentrations with AA and high concentrations with GM. Selective precipitations of Zn and Mn from acid solutions were carried out using NaOH and KOH. Using 3M NaOH as precipitating agent at room temperature and at pH 8; 95.4% of Zn and at pH 10; 93.7% of Mn were precipitated from the leach solution. Under the same conditions, using 3 M KOH at pH 8; 91.6% of Zn and at pH 10, 96.4% of Mn were precipitated. Based on the experimental results obtained, an appropriate flow sheet was proposed to recover both Zn and Mn.

Aug 1, 2013

By E. R. Spencer, D. R. Babich, L. A. Alcorn, A. K. Smith

Noise is one of the most pervasive health hazards in mining. A compilation of Mine Safety and Health Administration (MSHA) noise survey data for fiscal year 1990 shows that approximately 40% of the total samples taken for longwall occupations exceeded the Permissible Exposure Limit (PEL) of 100% (Gigliotti et al., 1991). To effectively determine worker noise exposures on longwall coal mining systems, it is necessary to provide accurate baseline measurements for these mining systems. This research was designed to develop measurement methods and test procedures for identifying noise sources that are major contributors to the underground noise exposure of longwall coal mining system workers. The measurement system that was used to analyze the noise sources around a stageloader used stationary dosimeters in a documented repeatable pattern to record the sound pressure and dose levels. A time-motion study of the cutting cycle and stageloader operator’s work cycle was done to correlate the sound levels at measurement locations and the resulting operator’s daily dose with significant noise events. Results from the underground measurements show that the highest sound levels recorded were at the stageloader discharge segment and tailpiece controls, where sound levels remained about the same throughout the test.

By W. H. Dickinson

The performance of seven antiscalants spanning a range of chemistries was evaluated for control of calcium carbonate (CaCO3) formation in gold processing applications. Three preferred chemistries were identified which provided up to 100 percent inhibition in static jar tests when applied at 30 ppm dosage. The three products were further evaluated using a model carbon extraction circuit developed for this application. The test circuit enabled direct measurement of calcium carbonate formed on the carbon from a supersaturated solution under dynamic conditions. The antiscalants lowered CaCO3 buildup on the columns by 15 - 26 percent compared to untreated controls. Impact of the antiscalants on the rate and extent of gold loading onto a carbon adsorbent was evaluated in laboratory carbon-in-pulp (CIP) studies. The antiscalants generated a 25 - 35% increase in gold loading at gold extraction efficiencies up to 65%. On-site testing at a gold processing facility demonstrated that 10 ppm of the preferred antiscalant was able to fully suppressCaCO3formation in thickener overflow water.

Feb 27, 2013

By H. H. Dewing

The Bureau of Mines constructed a process research unit (PRU) to demonstrate new technology for extracting zinc from sphalerite concentrates. Up to 9 kg/hr of sphalerite (ZnS) concentrate was reacted at ambient pressure in the PRU with 80 pct sulfuric acid at 160° to 180° C to produce zinc sulfate and elemental sulfur. The PRU consisted of a three-stage glass reactor system: a 4-liter premix stage in which feed was slurried with 78 to 82 pct H2S04, a 40-liter stirred reactor, and a ISO-liter settling stage in which high reaction conversions were effected and excess H2S04 for recycle was separated from insoluble ZnS04 and sulfur. Evolution of sulfur-containing gases was minimized by sub-surface addition of acid feed slurry to the stirred reactor and by exclusion of air from the reactor to prevent the oxidation of elemental sulfur. Conversion of zinc to zinc sulfate averaged over 99 pct at the optimum acid concentration of 80 pct. Total sulfur losses (primarily S02) were less than 2 pct of the sulfur in the sphalerite. Elemental sulfur remained in the insoluble portion of the settled reactor product after leaching with simulated spent zinc electrolyte containing sulfuric acid. The sulfur residue contained 75 to 89 pct sulfur. Neutral zinc sulfate, required for zinc electrowinning processes, was separated from the sulfuric acid leach solution by crystallization at -15° C as zinc sulfate heptahydrate (ZnS04?7H20). The crystallization operation simultaneously effected a partial concentration of the recycled electrolyte solution by removing water.

Jan 1, 1982

By Juan Patricio Ibáñez

Separation of arsenic and copper from Cu-As-H2S04 electrolytes by electrodialysis has been investigated at room temperature. The effects of current density and pH were studied. An arsenic-free copper solution was obtained for all the tested conditions. The transport efficiency for copper ions was found to be higher than 98% after 3 hours' test. Transport of arsenic and copper through the ion exchange membranes was increased by increasing pH and current density. Solution pH was found to be a key parameter for the separation process, since it controls the speciation of the ions to be transported and the formation of unwanted precipitates which reduce the global efficiency of the electrodialysis process. The main conclusion is that electrodialysis is a promising technique to be used in separating and/or concentrating ions of interest in copper electrometallurgy.

Jan 1, 2003

By Djavid Mohammad

Over the next several years, the storage capacity of the Metropolitan Water Reclamation District of Greater Chicago?s Tunnel and Reservoir Plan will be increased by 14.8 billion gallons through the addition of two large off-line reservoirs: the McCook and Thornton Reservoirs. The Thornton Reservoir will be constructed at the terminus of Calumet TARP System. The constructed TARP system will be connected to the Thornton Reservoir via connecting tunnels and gates systems. The connecting tunnels will comprise of: an upgradient transition tunnel, steel lined bifurcated tunnel for conveyance and control of flow, downdradient transition tunnel, and energy diffuser at tunnel portal. A large, approximately 250-foot-long, 69-foot-wide, and 40-foot-high, rock cavern will be excavated at an average depth of 320 feet to house the bifurcated tunnel system and associated six large control gates, each 12.5-ft by 28-ft wheel gate. Presented in this article are discussions about the TARP system, the Connecting Tunnels and gates Project, regional rock conditions, evaluation of reservoir?s wall stability for evaluation of tunnel penetration, and design challenges facing during design of the: rock cavern hosting the bifurcated tunnel system and gates and associated tunnels and shaft.

Jan 1, 2008

By William A. Macaitis, Frank E. Dalton, Leo R. DiVita

The Metropolitan Water Reclamation District of Greater Chicago's Tunnel and Reservoir Plan (TARP) is a multi-purpose urban public works project with a total cost of $3.7 billion. Currently 51 miles of TARP tunnels are completed and operational and 34 miles are under construction. The excavated TARP tunnels have been constructed in rock utilizing 29 tunnel boring machines, ranging in size from 6.5 to 35.3 feet in diameter.

Jan 1, 1993

By R. L. Virta

Four companies mined ball clay in four states during 2005. They included H.C. Spinks Clay (owned by Franklin Minerals), Kentucky-Tennessee Clay (owned by Imerys), Old Hickory Clay and Unimin. Production was estimated to be 1.32 Mt (1.45 million st) valued at $53.3 million, based on the results of a preliminary survey of the ball clay industry. Production in 2004 was 1.22 Mt (1.34 million st) valued at $54.1 million. Tennessee was the leading ball clay producer state with 61 percent of domestic production, followed by Texas, Mississippi and Kentucky.

Jan 1, 2006

By M. L. Leblanc, J. F. Burzynski, D. J. Mossman

A strong heterogeneity in the distribution of Sb+/-Au deposits exists within the North Atlantic Acadian-Hercynian domain. This is reflected in the regional disparity in Sb production among the various producing countries. This work focuses on the nature and distribution of Sb+/-Au occurrences in the Acadian-Hercynian domain. A summary listing of the general features of Sb-Au deposits found in this area is given

Dec 1, 1991

By Niklas Frank

Ore and waste transports form an integral part of any mining operation and represents a substantial portion of the mine´s total operating cost. Mine layout, truck fleet and size, production rates, haulage distances, shift schedules, maintenance strategies etc. are all important and not at all static variables. They all change during the life of a mine and interact in a dynamic way. It is therefore essential for the successful mine management to constantly analyse and optimise the mine's transport systems. Önnerlöv has recently conducted a life-of-mine haulage simulation project for Zinkgruvan Mining, a medium sized, underground zinc producer, located approximately 60 kilometers south of Örebro, Sweden. The main objective of the project was to analyse and optimise the investments required to provide ore and waste haulage under changing conditions over an +10- years period: Deepening of the mine, increased production rates, changed mine layout, changed truck fleet etc. A large number of scenarios has been tested in the simulation model in order to identify the "lowest cost per ton" solution. This paper comprises an introduction of Zinkgruvan Mining and a brief background to the actual project, a description of the simulation model, project conclusions and some useful hands-on tips for mining engineers and project managers how to run a successful simulation project.

May 1, 2003

By Lynch A. J

Comminution within rod mills has been investigated by use of a matrix analysis of breakage processes. A parameter, the number of breakage stages, has been introduced and comminution within all rod mills has been expressed in terms of the number of grinding stages and a function which describes the feed rate, mill diameter, and mill speed. The effect of variation in feed rate, feed sizing analysis and mill speed on the number of breakage stages is discussed, but no general relation is proposed because more study is needed.INTRODUCTIONRod mills are normally used as the first unit of multi-unit systems for the grinding of metalliferous ores and the cost of operating rod mills may be considerable. For both economic and metallurgical reasons, it is therefore necessary that the mills should be operated efficiently and that a knowledge of the mechanism of the size reduction process within rod mills should be as complete as possible. While a qualitative assessment of the process may be of some value, a quantitative assessment gained by describing the process in mathematical terms can be of much greater use because it may also be used for design and control purposes.In this paper, an empirical mathematical model is postulated to describe the size reduction process within rod mills and it is used to analyse the effects of variations in both rates and size distributions of the feed to the mills.GRINDING CHARACTERISTICS OF ROD MILLSMyers (1953) discussed the grinding characteristics of rod mills and suggested that a pronounced screening effect, resulting in the preferential grinding of the coarser particles, occurs within the mills. This is illustrated in...

Jan 1, 1964